The desired operating mode of the USB interface to this device.
JetDirect normally uses the best interface the device supports.
Setting this object limits the device to a simpler interface when
the more complex interface does not work with JetDirect.
automatic = use best available protocol
unidirectional = limit to forward data only (USB class 7.1.1)
bidirectional = limit to simple forward and reverse data (7.1.2)
mlc = limit to HP-MLC protocol (USB class 7.1.2+)
Parsed from file jdMibCV5.mib.txt
Company: hp
Module: JETDIRECT3-MIB
Child arc 0 is used to translate between SNMPv1 and SNMPv2 notification parameters as explained in IETF RFC 2576, section 3.
npPortUsbDesiredMode OBJECT-TYPE SYNTAX INTEGER { automatic(1), unidirectional(2), bidirectional(3), mlc(4) } MAX-ACCESS read-write STATUS current DESCRIPTION "The desired operating mode of the USB interface to this device. JetDirect normally uses the best interface the device supports. Setting this object limits the device to a simpler interface when the more complex interface does not work with JetDirect. automatic = use best available protocol unidirectional = limit to forward data only (USB class 7.1.1) bidirectional = limit to simple forward and reverse data (7.1.2) mlc = limit to HP-MLC protocol (USB class 7.1.2+) " ::={ npPort 12 }
OID | Name | Sub children | Sub Nodes Total | Description |
---|---|---|---|---|
1.3.6.1.4.1.11.2.4.3.13.12.0 | npPortUsbDesiredMode | 0 | 0 | None |
OID | Name | Sub children | Sub Nodes Total | Description |
---|---|---|---|---|
1.3.6.1.4.1.11.2.4.3.13.1 | 1 | 1 | 1 | npPortNumPorts |
1.3.6.1.4.1.11.2.4.3.13.2 | 2 | 1 | 1 | npPortType |
1.3.6.1.4.1.11.2.4.3.13.3 | npPortDesiredMode | 1 | 1 | The desired (remotely specified) operating mode of the parallel port. The following map is used to determine mode availability a… |
1.3.6.1.4.1.11.2.4.3.13.4 | npPortCentronicsHandshaking | 1 | 1 | The handshaking to be used in sending data over the parallel port. |
1.3.6.1.4.1.11.2.4.3.13.5 | npPortStatusLines | 1 | 1 | The state of the centronics status lines from the peripheral. The value is a bit mask. Bit Value Signal 0 0x01 … |
1.3.6.1.4.1.11.2.4.3.13.6 | npPortMaxModeAvaliable | 1 | 1 | The maximum available parallel mode by which the print-server may connect to an attached peripheral. This is a function of the t… |
1.3.6.1.4.1.11.2.4.3.13.7 | npPortBidiPollRate | 1 | 1 | Poll rate for bi-directional data. Range is 10 to 100 seconds. Defaults to 40 seconds. |
1.3.6.1.4.1.11.2.4.3.13.8 | npPortSetCentronicsTiming | 1 | 1 | Takes the 16 bit value and applies it to the centronics timing register. The default value is 0 and is not applied to the centroni… |
1.3.6.1.4.1.11.2.4.3.13.9 | npPortSetIoFlags | 1 | 1 | Sets and/or disables IO flags. Reset value of 0. EX-ONLY |
1.3.6.1.4.1.11.2.4.3.13.10 | npPortSetEcpHostRecTimer | 1 | 1 | Takes the 16 bit value and applies it to the Host Recovery Time Register. The default value is 0. EX-ONLY |
1.3.6.1.4.1.11.2.4.3.13.11 | npPortSetIoFlags2 | 1 | 1 | Sets and/or disables IO flags. Reset value of 0. EX-ONLY |
1.3.6.1.4.1.11.2.4.3.13.13 | npPortUsbCurrentMode | 1 | 1 | The current operating mode of the USB interface to this device. unknown = unknown or no device connected unidirectional =… |
1.3.6.1.4.1.11.2.4.3.13.14 | npPortUsbProduct | 1 | 1 | The product string (if any) returned by the current USB device on this port. |
1.3.6.1.4.1.11.2.4.3.13.15 | npPortUsbManufacturer | 1 | 1 | The manufacturer string (if any) returned by the current USB device on this port. |
1.3.6.1.4.1.11.2.4.3.13.16 | npPortUsbSerialNumber | 1 | 1 | The serial number string (if any) returned by the current USB device on this port. |