The source of Transmit Clock.
'loopTiming' indicates that the recovered receive
clock is used as the transmit clock.
'SystemTiming' indicates that a system clock
source is used or when an external clock is
attached to the box containing the interface.
Parsed from file mariposa.mib.txt
Company: marconi
Module: MARIPOSA-MIB
Vendor: Marconi
Module: MARIPOSA-MIB (mariposa.mib)
Type: TABULAR
Access: read-write
Syntax: INTEGER
Automatically extracted from www.mibdepot.com
scesPhyTxClockSource OBJECT-TYPE SYNTAX INTEGER { loopTiming (1), systemTiming (2) } ACCESS read-write STATUS mandatory DESCRIPTION "The source of Transmit Clock. 'loopTiming' indicates that the recovered receive clock is used as the transmit clock. 'SystemTiming' indicates that a system clock source is used or when an external clock is attached to the box containing the interface." ::= { scesPhyEntry 9 }
| OID | Name | Sub children | Sub Nodes Total | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.2426.1.2.6.7.1.1.1.1.1 | scesPhyIfIndex | 0 | 0 | This value for this object is equal to the value of ifIndex from the Interfaces table of MIB II (RFC 1213). |
| 1.3.6.1.4.1.2426.1.2.6.7.1.1.1.1.2 | scesPhyCurrentLineType | 0 | 0 | This object indicates the type of the line implementing this circuit. It defines the link type that is currently active in the sy… |
| 1.3.6.1.4.1.2426.1.2.6.7.1.1.1.1.3 | scesPhyStoredLineType | 0 | 0 | This object indicates the type of the line implementing this circuit that is saved in the flash. When the value of this object … |
| 1.3.6.1.4.1.2426.1.2.6.7.1.1.1.1.4 | scesPhyCurrentFraming | 0 | 0 | This object indicates the framing type that is used for this circuit. It defines the framing type that is currently active in the… |
| 1.3.6.1.4.1.2426.1.2.6.7.1.1.1.1.5 | scesPhyStoredFraming | 0 | 0 | This object indicates the framing type that is used for this circuit. It defines the framing type. The values, in sequence, desc… |
| 1.3.6.1.4.1.2426.1.2.6.7.1.1.1.1.6 | scesPhyCurrentLineCoding | 0 | 0 | This variable describes the variety of Zero Code Suppression that is currently used on this interface, which in turn affects a nu… |
| 1.3.6.1.4.1.2426.1.2.6.7.1.1.1.1.7 | scesPhyStoredLineCoding | 0 | 0 | This variable describes the variety of Zero Code Suppression of this interface that is saved in the flash. When the value of this… |
| 1.3.6.1.4.1.2426.1.2.6.7.1.1.1.1.8 | scesPhyLineLength | 0 | 0 | The length of the ds1 line in meters. This objects provides information for line build out circuitry if it exists and can use thi… |
| 1.3.6.1.4.1.2426.1.2.6.7.1.1.1.1.10 | scesPhyLoopbackMode | 0 | 0 | This variable represents the desired loopback configuration of the interface. Agents supporting read/write access should return b… |
| 1.3.6.1.4.1.2426.1.2.6.7.1.1.1.1.11 | scesPhySignalingMode | 0 | 0 | This object specifies signaling mode for SCES link. This can have CCS mode, CAS mode, CES Basic mode or CES with CAS, CAS Without… |
| 1.3.6.1.4.1.2426.1.2.6.7.1.1.1.1.12 | scesPhyAlarmReporting | 0 | 0 | This object identifies the Alarm Reporting of the sces voice. |
| 1.3.6.1.4.1.2426.1.2.6.7.1.1.1.1.13 | scesPhyVoiceCompanding | 0 | 0 | This object specifies the channel the voice companding technique - either A-law or mode. |
| 1.3.6.1.4.1.2426.1.2.6.7.1.1.1.1.14 | scesPhySystemClockSource | 0 | 0 | This object identifies the System Clock Source. It can be 1.Internal 2.ATM 3.CBR |
| 1.3.6.1.4.1.2426.1.2.6.7.1.1.1.1.15 | scesPhySystemClockSourceStatus | 0 | 0 | This objects specifies whether the clock source defined by 'systemClockSource' is refering to a valid resource or not. If the spe… |
| 1.3.6.1.4.1.2426.1.2.6.7.1.1.1.1.16 | scesPhyLossOfSignalState | 0 | 0 | Near end Loss Of Signal. When cells are continuously lost the value is set to loss (2). When cells are no longer lost, the value … |
| 1.3.6.1.4.1.2426.1.2.6.7.1.1.1.1.17 | scesPhyLossOfFrameState | 0 | 0 | Near end LOF (a.k.a., Red Alarm). For DS1 links, the Loss Of Frame failure is declared when an OOF or LOS defect has persisted fo… |
| 1.3.6.1.4.1.2426.1.2.6.7.1.1.1.1.18 | scesPhyXmtFarEndLOFFState | 0 | 0 | Near End is sending the LOF indication. |
| 1.3.6.1.4.1.2426.1.2.6.7.1.1.1.1.19 | scesPhyRcvFarEndLOFFState | 0 | 0 | The Far End LOF failure Alarm is also known as Yellow Alarm in the DS1 case, and Distant Alarm in the E1 case. For D4 links, the F… |
| 1.3.6.1.4.1.2426.1.2.6.7.1.1.1.1.20 | scesPhyAISFState | 0 | 0 | Far end sending Alarm Indication Signal(AIS) a.k.a Remote Alarm Indication (RAI). For D4 and ESF links, the 'all ones' condition … |
| 1.3.6.1.4.1.2426.1.2.6.7.1.1.1.1.21 | scesPhyXmtAISFState | 0 | 0 | Near end sending Alarm Indication Signal(AIS). For D4 and ESF links, the 'all ones' condition is detected at a DS1 line interface… |