The MIB module to configure the Frame Relay
connection configuration.
Terminologies Used:
SIW - Frame-Relay-to ATM Service Interworking.
In SIW, the ATM port connected to a frame
relay port does not need to be aware that
it is connected to an interworking function.
This is explained in document FRF.8.
NIW - Frame-Relay-to ATM Network Interworking.
In NIW, the ATM port connected to a frame
relay port does need to be aware that
it is connected to an interworking function.
PVC - Permanent Virtual Circuit OR
Permanent Virtual Connection
A frame relay logical link, whose endpoints
and class of service are defined by network
management. A PVC consists of the originating
frame relay network element address, originating
DLCI, terminating frame relay network element
address and terminating DLCI.
This is controlled by PAR(Portable Auto Route)
controller.
SPVC - Soft Permanent Virtual Circuits.
This is a PVC controlled by PNNI Controller.
Frame Relay PVC/SPVC end-point/Channel is referred to as
frame Relay connection in this MIB.
Traffic shaping parameters:
CIR, EIR, Bc, Be, DE, Tc, AR corresponding to
rate of the physical interface.
CIR - Committed Information Rate.
This is the rate of traffic that the PVC
will support as 'comitted' traffic.
The committed rate(in bits per second) at which
the ingress access interface trunk interfaces,
and egress access interface of a frame relay
network transfer information to the destination
frame relay end system under normal conditions.
The rate is averaged over a minimum time interval
Tc.
AR - Access Rate
The maximum number of bits per second that an end
station can transmit into the network is
bounded by the acess rate of the user-network
interface. The line speed of the user network
connection limits the access rate.
Bc - Committed Burst Size
The maximum amount of data(in bits) that the
network agrees to transfer, under normal conditions
during a time interval Tc.
The data is in bytes in the current implementation.
Be - Excess Burst Size
The maximum amount of uncommitted data(in bits)
in excess of BC that a frame relay network can
attempt to deliver during a time interval Tc.
This data generally is delivered with a low
probability than Bc. The network treats Be
data as discard eligible.
The data is in bytes in the current implementation.
Tc - The committed rate measurement interval.
The time interval during which the user can send
only BC committed amount of data and BE excess
amount of data.
EIR - Excess Information Rate
This is the bandwidth in excess of CIR
the PVC will be allowed to burst on a
a given PVC.
The average rate at which excess traffic is
to be policed. This number is computed based
on Bc, Be, CIR and Tc.
DE - Discard Eligibility
Frame Forwarding Port: Frame Forwarding Ports are identified
by portType = frame-forward(3).
NOTE: The objects related to frame relay ports are
available in ifTable,if ifTable is implemented
in service module/card.
Following Service Modules support ifTable:
FRSM-12
Parsed from file CISCO-WAN-FR-CONN-MIB.mib
Module: CISCO-WAN-FR-CONN-MIB
The MIB module to configure the Frame Relay
connection configuration.
Terminologies Used:
SIW - Frame-Relay-to ATM Service Interworking.
In SIW, the ATM port connected to a frame
relay port does not need to be aware that
it is connected to an interworking function.
This is explained in document FRF.8.
NIW - Frame-Relay-to ATM Network Interworking.
In NIW, the ATM port connected to a frame
relay port does need to be aware that
it is connected to an interworking function.
PVC - Permanent Virtual Circuit OR
Permanent Virtual Connection
A frame relay logical link, whose endpoints
and class of service are defined by network
management. A PVC consists of the originating
frame relay network element address, originating
DLCI, terminating frame relay network element
address and terminating DLCI.
This is controlled by PAR(Portable Auto Route)
controller.
SPVC - Soft Permanent Virtual Circuits.
This is a PVC controlled by PNNI Controller.
Frame Relay PVC/SPVC end-point/Channel is referred to as
frame Relay connection in this MIB.
Traffic shaping parameters:
CIR, EIR, Bc, Be, DE, Tc, AR corresponding to
rate of the physical interface.
CIR - Committed Information Rate.
This is the rate of traffic that the PVC
will support as 'comitted' traffic.
The committed rate(in bits per second) at which
the ingress access interface trunk interfaces,
and egress access interface of a frame relay
network transfer information to the destination
frame relay end system under normal conditions.
The rate is averaged over a minimum time interval
Tc.
AR - Access Rate
The maximum number of bits per second that an end
station can transmit into the network is
bounded by the acess rate of the user-network
interface. The line speed of the user network
connection limits the access rate.
Bc - Committed Burst Size
The maximum amount of data(in bits) that the
network agrees to transfer, under normal conditions
during a time interval Tc.
The data is in bytes in the current implementation.
Be - Excess Burst Size
The maximum amount of uncommitted data(in bits)
in excess of BC that a frame relay network can
attempt to deliver during a time interval Tc.
This data generally is delivered with a low
probability than Bc. The network treats Be
data as discard eligible.
The data is in bytes in the current implementation.
Tc - The committed rate measurement interval.
The time interval during which the user can send
only BC committed amount of data and BE excess
amount of data.
EIR - Excess Information Rate
This is the bandwidth in excess of CIR
the PVC will be allowed to burst on a
a given PVC.
The average rate at which excess traffic is
to be policed. This number is computed based
on Bc, Be, CIR and Tc.
DE - Discard Eligibility
Frame Forwarding Port: Frame Forwarding Ports are identified
by portType = frame-forward(3).
NOTE: The objects related to frame relay ports are
available in ifTable,if ifTable is implemented
in service module/card.
Following Service Modules support ifTable:
FRSM-12
Parsed from file CISCO-WAN-FR-CONN-MIB.my.txt
Company: None
Module: CISCO-WAN-FR-CONN-MIB
The MIB module to configure the Frame Relay
connection configuration.
Terminologies Used:
SIW - Frame-Relay-to ATM Service Interworking.
In SIW, the ATM port connected to a frame
relay port does not need to be aware that
it is connected to an interworking function.
This is explained in document FRF.8.
NIW - Frame-Relay-to ATM Network Interworking.
In NIW, the ATM port connected to a frame
relay port does need to be aware that
it is connected to an interworking function.
PVC - Permanent Virtual Circuit OR
Permanent Virtual Connection
A frame relay logical link, whose endpoints
and class of service are defined by network
management. A PVC consists of the originating
frame relay network element address, originating
DLCI, terminating frame relay network element
address and terminating DLCI.
This is controlled by PAR(Portable Auto Route)
controller.
SPVC - Soft Permanent Virtual Circuits.
This is a PVC controlled by PNNI Controller.
Frame Relay PVC/SPVC end-point/Channel is referred to as
frame Relay connection in this MIB.
Traffic shaping parameters:
CIR, EIR, Bc, Be, DE, Tc, AR corresponding to
rate of the physical interface.
CIR - Committed Information Rate.
This is the rate of traffic that the PVC
will support as 'comitted' traffic.
The committed rate(in bits per second) at which
the ingress access interface trunk interfaces,
and egress access interface of a frame relay
network transfer information to the destination
frame relay end system under normal conditions.
The rate is averaged over a minimum time interval
Tc.
AR - Access Rate
The maximum number of bits per second that an end
station can transmit into the network is
bounded by the acess rate of the user-network
interface. The line speed of the user network
connection limits the access rate.
Bc - Committed Burst Size
The maximum amount of data(in bits) that the
network agrees to transfer, under normal conditions
during a time interval Tc.
The data is in bytes in the current implementation.
Be - Excess Burst Size
The maximum amount of uncommitted data(in bits)
in excess of BC that a frame relay network can
attempt to deliver during a time interval Tc.
This data generally is delivered with a low
probability than Bc. The network treats Be
data as discard eligible.
The data is in bytes in the current implementation.
Tc - The committed rate measurement interval.
The time interval during which the user can send
only BC committed amount of data and BE excess
amount of data.
EIR - Excess Information Rate
This is the bandwidth in excess of CIR
the PVC will be allowed to burst on a
a given PVC.
The average rate at which excess traffic is
to be policed. This number is computed based
on Bc, Be, CIR and Tc.
DE - Discard Eligibility
Frame Forwarding Port: Frame Forwarding Ports are identified
by portType = frame-forward(3).
NOTE: The objects related to frame relay ports are
available in ifTable,if ifTable is implemented
in service module/card.
Following Service Modules support ifTable:
FRSM-12
ciscoWanFrConnMIB MODULE-IDENTITY LAST-UPDATED "200209180000Z" ORGANIZATION "Cisco Systems, Inc." CONTACT-INFO " Cisco Systems Customer Service Postal: 170 W Tasman Drive San Jose, CA 95134 USA Tel: +1 800 553-NETS E-mail: [email protected]" DESCRIPTION "The MIB module to configure the Frame Relay connection configuration. Terminologies Used: SIW - Frame-Relay-to ATM Service Interworking. In SIW, the ATM port connected to a frame relay port does not need to be aware that it is connected to an interworking function. This is explained in document FRF.8. NIW - Frame-Relay-to ATM Network Interworking. In NIW, the ATM port connected to a frame relay port does need to be aware that it is connected to an interworking function. PVC - Permanent Virtual Circuit OR Permanent Virtual Connection A frame relay logical link, whose endpoints and class of service are defined by network management. A PVC consists of the originating frame relay network element address, originating DLCI, terminating frame relay network element address and terminating DLCI. This is controlled by PAR(Portable Auto Route) controller. SPVC - Soft Permanent Virtual Circuits. This is a PVC controlled by PNNI Controller. Frame Relay PVC/SPVC end-point/Channel is referred to as frame Relay connection in this MIB. Traffic shaping parameters: CIR, EIR, Bc, Be, DE, Tc, AR corresponding to rate of the physical interface. CIR - Committed Information Rate. This is the rate of traffic that the PVC will support as 'comitted' traffic. The committed rate(in bits per second) at which the ingress access interface trunk interfaces, and egress access interface of a frame relay network transfer information to the destination frame relay end system under normal conditions. The rate is averaged over a minimum time interval Tc. AR - Access Rate The maximum number of bits per second that an end station can transmit into the network is bounded by the acess rate of the user-network interface. The line speed of the user network connection limits the access rate. Bc - Committed Burst Size The maximum amount of data(in bits) that the network agrees to transfer, under normal conditions during a time interval Tc. The data is in bytes in the current implementation. Be - Excess Burst Size The maximum amount of uncommitted data(in bits) in excess of BC that a frame relay network can attempt to deliver during a time interval Tc. This data generally is delivered with a low probability than Bc. The network treats Be data as discard eligible. The data is in bytes in the current implementation. Tc - The committed rate measurement interval. The time interval during which the user can send only BC committed amount of data and BE excess amount of data. EIR - Excess Information Rate This is the bandwidth in excess of CIR the PVC will be allowed to burst on a a given PVC. The average rate at which excess traffic is to be policed. This number is computed based on Bc, Be, CIR and Tc. DE - Discard Eligibility Frame Forwarding Port: Frame Forwarding Ports are identified by portType = frame-forward(3). NOTE: The objects related to frame relay ports are available in ifTable,if ifTable is implemented in service module/card. Following Service Modules support ifTable: FRSM-12 " REVISION "200209180000Z" DESCRIPTION "Initial version of the MIB. The content of this MIB was originally available in CISCO-WAN-AXIPOP-MIB defined using SMIv1. The applicable objects from CISCO-WAN-AXIPOP-MIB are defined using SMIv2 in this MIB. Also the descriptions of some of the objects have been modified." ::= { ciscoWan 47 }
ciscoWanFrConnMIB OBJECT IDENTIFIER ::= { ciscoWan 47 }
Vendor: Stratacom
Module: CISCO-WAN-FR-CONN-MIB
[Automatically extracted from oidview.com]
ciscoWanFrConnMIB MODULE-IDENTITY LAST-UPDATED "200209180000Z" ORGANIZATION "Cisco Systems, Inc." CONTACT-INFO " Cisco Systems Customer Service Postal: 170 W Tasman Drive San Jose, CA 95134 USA Tel: +1 800 553-NETS E-mail: [email protected]" DESCRIPTION "The MIB module to configure the Frame Relay connection configuration. Terminologies Used: SIW - Frame-Relay-to ATM Service Interworking. In SIW, the ATM port connected to a frame relay port does not need to be aware that it is connected to an interworking function. This is explained in document FRF.8. NIW - Frame-Relay-to ATM Network Interworking. In NIW, the ATM port connected to a frame relay port does need to be aware that it is connected to an interworking function. PVC - Permanent Virtual Circuit OR Permanent Virtual Connection A frame relay logical link, whose endpoints and class of service are defined by network management. A PVC consists of the originating frame relay network element address, originating DLCI, terminating frame relay network element address and terminating DLCI. This is controlled by PAR(Portable Auto Route) controller. SPVC - Soft Permanent Virtual Circuits. This is a PVC controlled by PNNI Controller. Frame Relay PVC/SPVC end-point/Channel is referred to as frame Relay connection in this MIB. Traffic shaping parameters: CIR, EIR, Bc, Be, DE, Tc, AR corresponding to rate of the physical interface. CIR - Committed Information Rate. This is the rate of traffic that the PVC will support as 'comitted' traffic. The committed rate(in bits per second) at which the ingress access interface trunk interfaces, and egress access interface of a frame relay network transfer information to the destination frame relay end system under normal conditions. The rate is averaged over a minimum time interval Tc. AR - Access Rate The maximum number of bits per second that an end station can transmit into the network is bounded by the acess rate of the user-network interface. The line speed of the user network connection limits the access rate. Bc - Committed Burst Size The maximum amount of data(in bits) that the network agrees to transfer, under normal conditions during a time interval Tc. The data is in bytes in the current implementation. Be - Excess Burst Size The maximum amount of uncommitted data(in bits) in excess of BC that a frame relay network can attempt to deliver during a time interval Tc. This data generally is delivered with a low probability than Bc. The network treats Be data as discard eligible. The data is in bytes in the current implementation. Tc - The committed rate measurement interval. The time interval during which the user can send only BC committed amount of data and BE excess amount of data. EIR - Excess Information Rate This is the bandwidth in excess of CIR the PVC will be allowed to burst on a a given PVC. The average rate at which excess traffic is to be policed. This number is computed based on Bc, Be, CIR and Tc. DE - Discard Eligibility Frame Forwarding Port: Frame Forwarding Ports are identified by portType = frame-forward(3). NOTE: The objects related to frame relay ports are available in ifTable,if ifTable is implemented in service module/card. Following Service Modules support ifTable: FRSM-12 " REVISION "200209180000Z" DESCRIPTION "Initial version of the MIB. The content of this MIB was originally available in CISCO-WAN-AXIPOP-MIB defined using SMIv1. The applicable objects from CISCO-WAN-AXIPOP-MIB are defined using SMIv2 in this MIB. Also the descriptions of some of the objects have been modified." ::= { ciscoWan 47 }
ciscoWanFrConnMIB MODULE-IDENTITY LAST-UPDATED "200209180000Z" ORGANIZATION "Cisco Systems, Inc." CONTACT-INFO " Cisco Systems Customer Service Postal: 170 W Tasman Drive San Jose, CA 95134 USA Tel: +1 800 553-NETS E-mail: [email protected]" DESCRIPTION "The MIB module to configure the Frame Relay connection configuration. Terminologies Used: SIW - Frame-Relay-to ATM Service Interworking. In SIW, the ATM port connected to a frame relay port does not need to be aware that it is connected to an interworking function. This is explained in document FRF.8. NIW - Frame-Relay-to ATM Network Interworking. In NIW, the ATM port connected to a frame relay port does need to be aware that it is connected to an interworking function. PVC - Permanent Virtual Circuit OR Permanent Virtual Connection A frame relay logical link, whose endpoints and class of service are defined by network management. A PVC consists of the originating frame relay network element address, originating DLCI, terminating frame relay network element address and terminating DLCI. This is controlled by PAR(Portable Auto Route) controller. SPVC - Soft Permanent Virtual Circuits. This is a PVC controlled by PNNI Controller. Frame Relay PVC/SPVC end-point/Channel is referred to as frame Relay connection in this MIB. Traffic shaping parameters: CIR, EIR, Bc, Be, DE, Tc, AR corresponding to rate of the physical interface. CIR - Committed Information Rate. This is the rate of traffic that the PVC will support as 'comitted' traffic. The committed rate(in bits per second) at which the ingress access interface trunk interfaces, and egress access interface of a frame relay network transfer information to the destination frame relay end system under normal conditions. The rate is averaged over a minimum time interval Tc. AR - Access Rate The maximum number of bits per second that an end station can transmit into the network is bounded by the acess rate of the user-network interface. The line speed of the user network connection limits the access rate. Bc - Committed Burst Size The maximum amount of data(in bits) that the network agrees to transfer, under normal conditions during a time interval Tc. The data is in bytes in the current implementation. Be - Excess Burst Size The maximum amount of uncommitted data(in bits) in excess of BC that a frame relay network can attempt to deliver during a time interval Tc. This data generally is delivered with a low probability than Bc. The network treats Be data as discard eligible. The data is in bytes in the current implementation. Tc - The committed rate measurement interval. The time interval during which the user can send only BC committed amount of data and BE excess amount of data. EIR - Excess Information Rate This is the bandwidth in excess of CIR the PVC will be allowed to burst on a a given PVC. The average rate at which excess traffic is to be policed. This number is computed based on Bc, Be, CIR and Tc. DE - Discard Eligibility Frame Forwarding Port: Frame Forwarding Ports are identified by portType = frame-forward(3). NOTE: The objects related to frame relay ports are available in ifTable,if ifTable is implemented in service module/card. Following Service Modules support ifTable: FRSM-12 " REVISION "200209180000Z" DESCRIPTION "Initial version of the MIB. The content of this MIB was originally available in CISCO-WAN-AXIPOP-MIB defined using SMIv1. The applicable objects from CISCO-WAN-AXIPOP-MIB are defined using SMIv2 in this MIB. Also the descriptions of some of the objects have been modified." ::= { ciscoWan 47 }
| OID | Name | Sub children | Sub Nodes Total | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.351.150.47.2 | ciscoWanFrConnMIBConformance | 2 | 10 | None |
| OID | Name | Sub children | Sub Nodes Total | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.351.150.1 | ciscoWanAtmConnMIB | 2 | 103 | This MIB is used for configuring/provisioning SPVCs on the ATM interfaces. This is used for ATM switch connection management. Term… |
| 1.3.6.1.4.1.351.150.2 | ciscoWanAtmConnStatMIB | 3 | 155 | This module contains ATM switch connection related real time statistical counter objects. |
| 1.3.6.1.4.1.351.150.3 | ciscoWANSonetMIB | 2 | 106 | The MIB module to describe SONET/SDH interfaces objects. This is an extension to the standard SONET MIB(RFC 2558). |
| 1.3.6.1.4.1.351.150.5 | ciscoWanTrapVarsMIB | 2 | 51 | This MIB module is for Supporting Varbinds used only in trap defintions. The NMS applications should not depend on the implementa… |
| 1.3.6.1.4.1.351.150.7 | ciscoMGX8800IfMappingMIB | 2 | 13 | This MIB module is used for getting the ifIndex values given physical location and/or logical information. The physical informati… |
| 1.3.6.1.4.1.351.150.9 | ciscoWanRpmConnExtMIB | 2 | 19 | This MIB together with the CISCO-WAN-ATM-CONN-MIB support provisioning of PVC endpoints and SPVCs on the MGX's Route Processor Mo… |
| 1.3.6.1.4.1.351.150.10 | ciscoWanMgMIB | 2 | 85 | The MIB module for managing Media Gateways (MGs). Terms used: MG: Media Gateway MGC: Media Gateway Controller MGCP: Media Gatewa… |
| 1.3.6.1.4.1.351.150.11 | ciscoWanSrcpMIB | 2 | 51 | The MIB module for managing SRCP(Simple Resource Coordination Protocol) implementations. SRCP is a resource coordination protocol… |
| 1.3.6.1.4.1.351.150.15 | ciscoWanFeederMIB | 2 | 25 | This MIB is used for configuring a port on an ATM switch module to be aware of feeder connection information. Terminology: AR - Aut… |
| 1.3.6.1.4.1.351.150.16 | ciscoWanAtmCosbMIB | 2 | 29 | The MIB to manage CoS(Class of Service) queue/buffer related parameters. One or more virtual interfaces may exist on a physical in… |
| 1.3.6.1.4.1.351.150.17 | ciscoWanAal2ProfilesMIB | 2 | 17 | The MIB module for configuring AAL2 profile elements. This table will be used in AAL2 switching and trunking applications. |
| 1.3.6.1.4.1.351.150.18 | ciscoWanPersistentXgcpEventsMIB | 2 | 12 | The MIB module for managing CA(Call Agent) events. |
| 1.3.6.1.4.1.351.150.19 | ciscoWanT38FaxRelayMIB | 3 | 28 | The MIB module for configuring T.38 fax relay protocol parameters. This MIB will be used in VoIP(Voice over IP) applications. |
| 1.3.6.1.4.1.351.150.20 | ciscoWanRtpConnMIB | 3 | 46 | The MIB module is defined for establishing connection between an endpoint and another endpoint on a remote VISM in the case of Vo… |
| 1.3.6.1.4.1.351.150.21 | ciscoWanCodecGenParmMIB | 3 | 14 | This MIB provides configuration of Jitter buffer mode on a call and initial jitter delay value per Codec based. Prior to this, th… |
| 1.3.6.1.4.1.351.150.22 | ciscoWanMgcRedunMIB | 3 | 31 | The MIB module for Media Gateways (MGs) to allow multiple Media Gateway Controllers (MGCs) to be configured and managed on the Ga… |
| 1.3.6.1.4.1.351.150.23 | ciscoWanLapdTrunkMIB | 3 | 18 | The MIB module is defined for establishing a Trunk to transport PRI (Primary Rate Interface) signaling information over a RUDP (R… |
| 1.3.6.1.4.1.351.150.24 | vismTonePlanGrpMIB | 3 | 83 | The MIB module is defined to configure the programmable Tone Plan feature on VISM. |
| 1.3.6.1.4.1.351.150.25 | ciscoWanAnnouncementMIB | 3 | 31 | The MIB module is defined to configure the Announcements feature on the Media Gateway Card. The Media Gateway Card will have the … |
| 1.3.6.1.4.1.351.150.30 | ciscoWanSrmMIB | 1 | 6 | The MIB module for configuration of bulk distribution (de-multiplexing of traffic from higher-bandwidth to lower-bandwidth interf… |
| 1.3.6.1.4.1.351.150.31 | ciscoWanSrmBertMIB | 1 | 7 | The MIB Module for BERT(Bit Error Rate Testing) using Service Resource Module(SRM). This MIB module is used for BERT on FRSM, AUS… |
| 1.3.6.1.4.1.351.150.32 | ciscoWanBbifPortMIB | 1 | 8 | The MIB module for configuration of ATM logical ports in PXM1 Service module in MGX82xx series. This MIB contains information on … |
| 1.3.6.1.4.1.351.150.33 | ciscoWanBbifIlmiMIB | 1 | 6 | The MIB module for ILMI configuration and ILMI statistics for broad band interface ports in PXM1 service module. PXM1 service mod… |
| 1.3.6.1.4.1.351.150.35 | ciscoWanBbifAtmConnMIB | 1 | 7 | The MIB module to configure the ATM Connections on a broad band interface in PXM1 Service module. |
| 1.3.6.1.4.1.351.150.36 | ciscoWanBbifAtmConnStatMIB | 1 | 5 | This MIB module contains ATM Connection related real time statistical counter objects. The ATM connections are applicable to PXM1… |
| 1.3.6.1.4.1.351.150.38 | ciscoMgx82xxVirtualPortMIB | 1 | 8 | The MIB module for configuration ond reporting statistics of virtual ports in PXM1 Service module in MGX82xx series. |
| 1.3.6.1.4.1.351.150.39 | ciscoMgx82xxDsx3BertMIB | 1 | 5 | The MIB Module for BERT (Bit Error Rate Testing) on ds3 interfaces in some of the cards (Service Modules) in MGX products. This M… |
| 1.3.6.1.4.1.351.150.40 | ciscoWanCesPortMIB | 1 | 7 | The MIB module to configure the Circuit Emulation Service(CES) ports. |
| 1.3.6.1.4.1.351.150.41 | ciscoWanCesRsrcPartMIB | 1 | 5 | The mib module to configure the resource partition on Circuit Emulation Service(CES) ports. This is applicable for service module… |
| 1.3.6.1.4.1.351.150.42 | ciscoWanCesConnMIB | 1 | 7 | The MIB module to configure the Circuit Emulation connections in MGX82xx series products. Terminology: CES : Circui… |
| 1.3.6.1.4.1.351.150.43 | ciscoWanCesConnStatMIB | 1 | 6 | The MIB module to provide CES Connections statistics. This MIB is supported in Circuit Emulation Service Modules(CESM) in MGX82xx, … |
| 1.3.6.1.4.1.351.150.44 | ciscoWanFrPortMIB | 1 | 11 | The MIB module to create/configure frame relay ports/interfaces. This module contains tables related to frame relay port states a… |
| 1.3.6.1.4.1.351.150.45 | ciscoWanFrRsrcPartMIB | 1 | 5 | The MIB module to configure the resource partition on Frame Relay Ports. Terminlogies used: LCN : Logical Connection Number. DLCI … |
| 1.3.6.1.4.1.351.150.46 | ciscoWanFrSignalingMIB | 1 | 8 | The MIB module to configure LMI and CLLM on a frame relay ports. This mib module also contains objects to represent LMI and CLLM s… |
| 1.3.6.1.4.1.351.150.48 | ciscoWanFrConnStatMIB | 1 | 7 | The MIB module for frame relay connection statistics. Terminologies Used: SIW - Frame-Relay-to ATM Service Interworking FECN … |
| 1.3.6.1.4.1.351.150.49 | ciscoWanFrX21MIB | 1 | 8 | The MIB module to configure X.21/HSSI physical and logical interfaces. This MIB module also contains alarm configuration of X.21 i… |
| 1.3.6.1.4.1.351.150.58 | ciscoMgx82xxDsx1MIB | 1 | 9 | The MIB module to configure DS1/E1 interface objects. This mib also contains the alarm configuration of DS1/E1 interfaces. This m… |
| 1.3.6.1.4.1.351.150.59 | ciscoMgx82xxDsx3MIB | 1 | 19 | The MIB Module for DS3/E3 interface configuration , statistics and Alarm configuration. This MIB is supported in T3/E3 service mod… |
| 1.3.6.1.4.1.351.150.60 | ciscoMgx82xxRpmSubIfMIB | 1 | 5 | This MIB is used to provision backplane sub-interfaces on the MGX's Route Processor Module (RPM). This MIB is implemented on the… |
| 1.3.6.1.4.1.351.150.61 | ciscoMgx82xxRpmRsrcPartMIB | 1 | 5 | The MIB module to manage resource partition objects. A resource partition is configured on a RPM subinterface. An administrator c… |
| 1.3.6.1.4.1.351.150.62 | ciscoMgx82xxRpmConnMIB | 1 | 5 | The connection MIB module for RPM(Router Blade) service module in MGX8250/MGX8230 products. The 'channel' and 'connection' and 'c… |
| 1.3.6.1.4.1.351.150.63 | ciscoWanParMIB | 1 | 15 | The MIB module for configuring AutoRoute controller. The Portable AutoRoute(PAR) is a Controller providing routing capabilities i… |
| 1.3.6.1.4.1.351.150.67 | basisMIB | 0 | 0 | This MIB Contains OID subtrees used in some of the MIBs under 'stratacom' enterprise. |
| 1.3.6.1.4.1.351.150.69 | basisSerialMIB | 1 | 5 | The MIB module to configure serial ports in Processor Module and different Service Modules(cards) in MGX8850,MGX8250 and MGX8220 A… |
| 1.3.6.1.4.1.351.150.70 | ciscoMgx82xxEnvmonMIB | 1 | 6 | The MIB module to describe the status of the Environmental Monitoring devices in MGX82xx products. |
| 1.3.6.1.4.1.351.150.71 | ciscoMgx82xxAtmUniPortMIB | 1 | 6 | The MIB module containing objects related to user-side of the ATM UNI Port. The mib is applicable for MGX8250 and MGX8220 product… |
| 1.3.6.1.4.1.351.150.72 | ciscoMgx82xxPxmClockMIB | 1 | 8 | The MIB module to describe the clock configuration in Processor Switch Module(PXM) in MGX82xx product. Back cards supported for … |
| 1.3.6.1.4.1.351.150.73 | ciscoMgx82xxModuleRsrcPartMIB | 1 | 5 | The MIB module to configure the resource partition on service modules(cards) supported in MGX82xx and MGX88xx products. This MIB i… |
| 1.3.6.1.4.1.351.150.74 | ciscoMgx82xxCardFeatureMIB | 1 | 7 | The MIB module which describes the features supported in MGX82XX products. This MIB Module provides the features supported in Cont… |
| 1.3.6.1.4.1.351.150.79 | ciscoVismDsx1MIB | 1 | 18 | The MIB module to configure DS1/E1 interface objects in a Voice Interworking Service Module (VISM) module. This MIB is an extensi… |
| 1.3.6.1.4.1.351.150.80 | basisOnlineDiagMIB | 1 | 5 | This MIB contains information on the online diagnostics in MGX82xx(MGX8250, MGX8220, MGX8230 etc) products. |
| 1.3.6.1.4.1.351.150.81 | ciscoVismDsx0MIB | 1 | 12 | This MIB module contains ds0 configuration, Status and DS0 related information on a DS1 interface supported in VISM module. VISM i… |
| 1.3.6.1.4.1.351.150.82 | ciscoVismModuleMIB | 1 | 26 | This MIB module contains VISM Card specific attributes and call statistics information for VISM service module. |
| 1.3.6.1.4.1.351.150.86 | ciscoVismConnMIB | 1 | 8 | The MIB module to contains configuration and connection state information the VISM. For VoIP(Voice over IP) support, VISM needs o… |
| 1.3.6.1.4.1.351.150.87 | ciscoVismAtmTrunkMIB | 1 | 10 | The MIB module contain the Bearer and CID (Channel Identifier) connection information. |
| 1.3.6.1.4.1.351.150.88 | ciscoVismCasMIB | 1 | 7 | The MIB module contain the CAS backhaul feature in VISM |
| 1.3.6.1.4.1.351.150.89 | ciscoVismConnStatMIB | 1 | 11 | The MIB module contain VISM channel counters information. |
| 1.3.6.1.4.1.351.150.90 | ciscoVismSvcMIB | 1 | 8 | The MIB module containing SVC information for VISM service module. |
| 1.3.6.1.4.1.351.150.91 | ciscoVismHdlcMIB | 1 | 6 | The MIB module containing table for configurating and maintaining counters for the HDLC channel on VISM service module. |
| 1.3.6.1.4.1.351.150.92 | ciscoVismPortMIB | 1 | 5 | The MIB module containing Port information for VISM service module. |
| 1.3.6.1.4.1.351.150.93 | ciscoVismRsrcPartMIB | 1 | 5 | The MIB module containing Port Resource Partition information for VISM service module. |
| 1.3.6.1.4.1.351.150.94 | ciscoVismXgcpExtMIB | 1 | 8 | The MIB module contain the XGCP MIB feature in VISM |
| 1.3.6.1.4.1.351.150.95 | ciscoVismSessionMIB | 1 | 8 | The MIB module contain the RUDP session parameter. The relationship between session set, session group and RUDP session is that: … |
| 1.3.6.1.4.1.351.150.96 | ciscoVismCacMIB | 1 | 6 | The MIB module containing the CAC information for VISM service module. |
| 1.3.6.1.4.1.351.150.97 | ciscoVismCodecMIB | 1 | 8 | The MIB module contains tables for configurating and maintaining Codec on VISM service module. |