Sets the binary communications protocol (BCP) for
communicating over a serial interface to a PostScript
printer.
Choices
Normal: Enables standard, ASCII (7-bit) hex protocol.
Data is sent and received in ASCII format. This mode is
recommended if you do not print binary data. It was
designed for data in the printable ASCII range. Print
jobs can change this setting through PostScript
operators.
Normal Fixed: Enables standard, ASCII (7-bit) hex
protocol. Print jobs cannot change this setting
through PostScript operators.
Binary: Enables binary communications protocol
(BCP). Print jobs can change this setting through
PostScript operators. Data in the printable ASCII range
also prints.
Binary Fixed: Enables binary fixed communications
protocol (BCP). Print jobs cannot alter change this
setting through PostScript operators. Data in the
printable ASCII range also prints.
Default
Normal
Parsed from file QMS-MIB.mib
Module: QMS-MIB
Vendor: QMS, Inc.
Module: QMS-MIB
[Automatically extracted from oidview.com]
qmsSerPSProtocol OBJECT-TYPE SYNTAX INTEGER { normal(1), normalfixed(2), binary(3), binaryfixed(4) } ACCESS read-write STATUS mandatory DESCRIPTION "Sets the binary communications protocol (BCP) for communicating over a serial interface to a PostScript printer. Choices Normal: Enables standard, ASCII (7-bit) hex protocol. Data is sent and received in ASCII format. This mode is recommended if you do not print binary data. It was designed for data in the printable ASCII range. Print jobs can change this setting through PostScript operators. Normal Fixed: Enables standard, ASCII (7-bit) hex protocol. Print jobs cannot change this setting through PostScript operators. Binary: Enables binary communications protocol (BCP). Print jobs can change this setting through PostScript operators. Data in the printable ASCII range also prints. Binary Fixed: Enables binary fixed communications protocol (BCP). Print jobs cannot alter change this setting through PostScript operators. Data in the printable ASCII range also prints. Default Normal" ::= { qmsSerial 100 }
OID | Name | Sub children | Sub Nodes Total | Description |
---|---|---|---|---|
1.3.6.1.4.1.480.1.160.101 | qmsSerMode | 0 | 0 | Enables or disables the serial port. Choices Interactive: Establish two-way communication between the host and the printer. Noninte… |
1.3.6.1.4.1.480.1.160.102 | qmsSerEmulation | 0 | 0 | Sets the serial interface emulation. Choices PostScript, HPGL, HPPCL, HEXDUMP, LN03, QUIC2 CCITT, Line Printer, TIFF, CALS, CGM, E… |
1.3.6.1.4.1.480.1.160.103 | qmsSerPriority | 0 | 0 | Allows you to specify which jobs are printed first, according to the interface through which they are received, when jobs are re… |
1.3.6.1.4.1.480.1.160.104 | qmsSerBufferSize | 0 | 0 | Sets the minimum number of kilobytes of system memory allocated to the serial interface. Default 15 Notes This value must be less th… |
1.3.6.1.4.1.480.1.160.111 | qmsSerEndDocumentMode | 0 | 0 | Enables (and identifies an end-of-job sequence) or disables data stream sensing for the end-of-document (EOD) command. Choices None… |
1.3.6.1.4.1.480.1.160.112 | qmsSerSpoolTimeout | 0 | 0 | Sets the number of seconds the interface waits for data from the host before terminating a spooled print job. Choices 0-99999 Defau… |
1.3.6.1.4.1.480.1.160.201 | qmsSerBaudRate | 0 | 0 | Sets the rate data is transmitted (bits per second) over the serial interface. Choices 300, 600, 1200, 2400, 4800, 9600, 19200, 38… |
1.3.6.1.4.1.480.1.160.202 | qmsSerParity | 0 | 0 | Sets the check bit used to identify data transmission errors. Choices: None, Odd, Even Default: None Note: The printer's parity setti… |
1.3.6.1.4.1.480.1.160.203 | qmsSerIgnoreParity | 0 | 0 | Specifies how the printer should handle parity errors. Choices Off: Ignore parity errors. The printer prints its best interpretati… |
1.3.6.1.4.1.480.1.160.204 | qmsSerRxSWFlow | 0 | 0 | Sets the software communication protocol used by the printer to control communication from the host computer. Choices ETX/ACK, Rob… |
1.3.6.1.4.1.480.1.160.205 | qmsSerTxSWFlow | 0 | 0 | Sets the software communication protocol used by the host computer to control communication with the printer. Choices ETX/ACK, Non… |
1.3.6.1.4.1.480.1.160.206 | qmsSerDataBits | 0 | 0 | Sets the number of data bits transmitted per character. Choices 5 Bits, 6 Bits, 7 Bits, 8 Bits Default 8 Bits |
1.3.6.1.4.1.480.1.160.207 | qmsSerStopBits | 0 | 0 | Sets the number of stop bits transmitted per character. Choices 1 Bit, 2 Bits, 1 1/2 Bits Default One Bit |
1.3.6.1.4.1.480.1.160.208 | qmsSerHwCTS | 0 | 0 | Controls the flow of data between the printer and the host. Choices Off, On Default Off Notes If the host uses hardware flow control,… |
1.3.6.1.4.1.480.1.160.209 | qmsSerHwRTS | 0 | 0 | Controls the flow of data between the printer and the host. Choices Off, On Default Off Notes If the host uses hardware flow control,… |
1.3.6.1.4.1.480.1.160.210 | qmsSerHwDTR | 0 | 0 | Controls the flow of data between the printer and the host. Choices Off, On Default On Notes If the host uses hardware flow control, … |
1.3.6.1.4.1.480.1.160.211 | qmsSerHwDTRPOL | 0 | 0 | Controls the flow of data between the printer and the host. Choices Reverse, Normal Default Normal Notes If the host uses hardware fl… |
1.3.6.1.4.1.480.1.160.212 | qmsSerHwDSR | 0 | 0 | Controls the flow of data between the printer and the host. Choices Off, On Default Off Notes If the host uses hardware flow control,… |
1.3.6.1.4.1.480.1.160.213 | qmsSerHwDSRPOL | 0 | 0 | Controls the flow of data between the printer and the host. Choices Reverse, Normal Default Normal Notes If the host uses hardware f… |