Sets the serial interface emulation.
Choices
PostScript, HPGL, HPPCL, HEXDUMP, LN03, QUIC2
CCITT, Line Printer, TIFF, CALS, CGM, ESP
Default
ESP
Note: Only the installed emulations will be available to select
from.
Parsed from file QMS-MIB.mib
Module: QMS-MIB
Vendor: QMS, Inc.
Module: QMS-MIB
[Automatically extracted from oidview.com]
qmsSerEmulation OBJECT-TYPE SYNTAX INTEGER { postscript(1), hpgl(5), hppcl(6), hexdump(7), ln03(13), quic2(15), ccitt(19), lineprinter(20), tiff(22), cals(23), cgm(25), esp(201) } ACCESS read-write STATUS mandatory DESCRIPTION "Sets the serial interface emulation. Choices PostScript, HPGL, HPPCL, HEXDUMP, LN03, QUIC2 CCITT, Line Printer, TIFF, CALS, CGM, ESP Default ESP Note: Only the installed emulations will be available to select from." ::= { qmsSerial 102 }
OID | Name | Sub children | Sub Nodes Total | Description |
---|---|---|---|---|
1.3.6.1.4.1.480.1.160.100 | qmsSerPSProtocol | 0 | 0 | Sets the binary communications protocol (BCP) for communicating over a serial interface to a PostScript printer. Choices Normal: En… |
1.3.6.1.4.1.480.1.160.101 | qmsSerMode | 0 | 0 | Enables or disables the serial port. Choices Interactive: Establish two-way communication between the host and the printer. Noninte… |
1.3.6.1.4.1.480.1.160.103 | qmsSerPriority | 0 | 0 | Allows you to specify which jobs are printed first, according to the interface through which they are received, when jobs are re… |
1.3.6.1.4.1.480.1.160.104 | qmsSerBufferSize | 0 | 0 | Sets the minimum number of kilobytes of system memory allocated to the serial interface. Default 15 Notes This value must be less th… |
1.3.6.1.4.1.480.1.160.111 | qmsSerEndDocumentMode | 0 | 0 | Enables (and identifies an end-of-job sequence) or disables data stream sensing for the end-of-document (EOD) command. Choices None… |
1.3.6.1.4.1.480.1.160.112 | qmsSerSpoolTimeout | 0 | 0 | Sets the number of seconds the interface waits for data from the host before terminating a spooled print job. Choices 0-99999 Defau… |
1.3.6.1.4.1.480.1.160.201 | qmsSerBaudRate | 0 | 0 | Sets the rate data is transmitted (bits per second) over the serial interface. Choices 300, 600, 1200, 2400, 4800, 9600, 19200, 38… |
1.3.6.1.4.1.480.1.160.202 | qmsSerParity | 0 | 0 | Sets the check bit used to identify data transmission errors. Choices: None, Odd, Even Default: None Note: The printer's parity setti… |
1.3.6.1.4.1.480.1.160.203 | qmsSerIgnoreParity | 0 | 0 | Specifies how the printer should handle parity errors. Choices Off: Ignore parity errors. The printer prints its best interpretati… |
1.3.6.1.4.1.480.1.160.204 | qmsSerRxSWFlow | 0 | 0 | Sets the software communication protocol used by the printer to control communication from the host computer. Choices ETX/ACK, Rob… |
1.3.6.1.4.1.480.1.160.205 | qmsSerTxSWFlow | 0 | 0 | Sets the software communication protocol used by the host computer to control communication with the printer. Choices ETX/ACK, Non… |
1.3.6.1.4.1.480.1.160.206 | qmsSerDataBits | 0 | 0 | Sets the number of data bits transmitted per character. Choices 5 Bits, 6 Bits, 7 Bits, 8 Bits Default 8 Bits |
1.3.6.1.4.1.480.1.160.207 | qmsSerStopBits | 0 | 0 | Sets the number of stop bits transmitted per character. Choices 1 Bit, 2 Bits, 1 1/2 Bits Default One Bit |
1.3.6.1.4.1.480.1.160.208 | qmsSerHwCTS | 0 | 0 | Controls the flow of data between the printer and the host. Choices Off, On Default Off Notes If the host uses hardware flow control,… |
1.3.6.1.4.1.480.1.160.209 | qmsSerHwRTS | 0 | 0 | Controls the flow of data between the printer and the host. Choices Off, On Default Off Notes If the host uses hardware flow control,… |
1.3.6.1.4.1.480.1.160.210 | qmsSerHwDTR | 0 | 0 | Controls the flow of data between the printer and the host. Choices Off, On Default On Notes If the host uses hardware flow control, … |
1.3.6.1.4.1.480.1.160.211 | qmsSerHwDTRPOL | 0 | 0 | Controls the flow of data between the printer and the host. Choices Reverse, Normal Default Normal Notes If the host uses hardware fl… |
1.3.6.1.4.1.480.1.160.212 | qmsSerHwDSR | 0 | 0 | Controls the flow of data between the printer and the host. Choices Off, On Default Off Notes If the host uses hardware flow control,… |
1.3.6.1.4.1.480.1.160.213 | qmsSerHwDSRPOL | 0 | 0 | Controls the flow of data between the printer and the host. Choices Reverse, Normal Default Normal Notes If the host uses hardware f… |