This parameter specifies whether the unit will insert more
than one flag between frames. The range of this parameter is
yes and no.
The value is 'no'.
Parsed from file SYNC-RESEARCH-MIB.mib
Module: SYNC-RESEARCH-MIB
Vendor: Sync Research, Inc.
Module: SYNC-RESEARCH-MIB
[Automatically extracted from oidview.com]
frameRelayMultiflagSeparation OBJECT-TYPE SYNTAX INTEGER { yes(1), no(2) } ACCESS read-write STATUS mandatory DESCRIPTION "This parameter specifies whether the unit will insert more than one flag between frames. The range of this parameter is yes and no. The value is 'no'." ::= { frameRelayConfigEntry 34 }
OID | Name | Sub children | Sub Nodes Total | Description |
---|---|---|---|---|
1.3.6.1.4.1.485.3.5.5.1.1.1 | frameRelayConfigPortIndex | 0 | 0 | The port number that uniquely identifies this port. |
1.3.6.1.4.1.485.3.5.5.1.1.2 | frameRelayPortType | 0 | 0 | The Frame Relay port type. |
1.3.6.1.4.1.485.3.5.5.1.1.3 | frameRelayInitState | 0 | 0 | The initial state of the Frame Relay port. If configured for 'in-service', then the Frame Relay port will be brougt up automatica… |
1.3.6.1.4.1.485.3.5.5.1.1.4 | frameRelayClocking | 0 | 0 | Clocking source for this port. Setting 'internal' will cause the port to emulate a physical DCE, and setting external will cause t… |
1.3.6.1.4.1.485.3.5.5.1.1.5 | frameRelaySpeed | 0 | 0 | The ports speed in bits per second. The default value is 9600 bits per second. Speeds higher than 19200 are not supported on RS-23… |
1.3.6.1.4.1.485.3.5.5.1.1.6 | frameRelayLocalManagementProtocol | 0 | 0 | The ports management protocol type. Annex D = ANSI T1.617 Annex D LMI = Frame Relay Manufacturers LMI The default value is Annex D. |
1.3.6.1.4.1.485.3.5.5.1.1.7 | frameRelayLinkPollingTimer | 0 | 0 | Measured in seconds, intervals of 5 T391 - Annex D nT1 - LMI The default value for this field is 5 seconds. |
1.3.6.1.4.1.485.3.5.5.1.1.8 | frameRelayFullStatusPollingCount | 0 | 0 | The number of polls that a full status poll is issued. N391 - Annex D nT1 - LMI The default value for this field is 6. |
1.3.6.1.4.1.485.3.5.5.1.1.9 | frameRelayT1Timer | 0 | 0 | The default LLC T1 timer value in seconds. T1 should be greater than T2 and less than Ti. Currently supported values are 1 to 25 … |
1.3.6.1.4.1.485.3.5.5.1.1.10 | frameRelayT2Timer | 0 | 0 | The default LLC T2 timer value in tenths of seconds. If configured for 0 then the T2 timer is disabled and an RR frame will be se… |
1.3.6.1.4.1.485.3.5.5.1.1.11 | frameRelayTiTimer | 0 | 0 | The default LLC Ti (inactivity) timer value in seconds. Ti should be greater than T1. Currently supported values are 2 to 50 secon… |
1.3.6.1.4.1.485.3.5.5.1.1.12 | frameRelayRxWindowSize | 0 | 0 | The default LLC receive window (N3) size. Note that this is not the same receive window as defined in IEEE 802.2 LLC. This is N3… |
1.3.6.1.4.1.485.3.5.5.1.1.13 | frameRelayTxWindowSize | 0 | 0 | The defalut LLC transmit window size. Current allowable values are 1-7. The default value for this field is 7. |
1.3.6.1.4.1.485.3.5.5.1.1.14 | frameRelayMaxRetries | 0 | 0 | The default LLC maximum number of retries (N2 value). The default value for this field is 15. |
1.3.6.1.4.1.485.3.5.5.1.1.15 | frameRelayNAUName | 0 | 0 | The NAU name of this port. The default value for this field is all blank (filled with ASCII space 0x20 characters). |
1.3.6.1.4.1.485.3.5.5.1.1.16 | frameRelayVirtualMACAddress | 0 | 0 | The F/R WAN is treated as a token ring. This address is used for communication with other bridges in the network. |
1.3.6.1.4.1.485.3.5.5.1.1.17 | frameRelayVirtualRingNumber | 0 | 0 | The F/R WAN is treated as a token ring. This is the ring number for the F/R network to which the port is attached. It must be a u… |
1.3.6.1.4.1.485.3.5.5.1.1.18 | frameRelayVirtualBridgeNumber | 0 | 0 | The F/R WAN is treated as a token ring. This variable only has significance if more than 1 F/R port is configured. The default va… |
1.3.6.1.4.1.485.3.5.5.1.1.19 | frameRelayIPAddress | 0 | 0 | This is the IP Address of this interface. |
1.3.6.1.4.1.485.3.5.5.1.1.20 | frameRelayNetworkMask | 0 | 0 | This is the network mask to be used on this interface. |
1.3.6.1.4.1.485.3.5.5.1.1.21 | frameRelayDefaultGatewayAddress | 0 | 0 | Default gateway address to be used when sending responses on this interface. |
1.3.6.1.4.1.485.3.5.5.1.1.22 | frameRelaySessSwitchThreshold | 0 | 0 | frameRelaySessSwitchthreshold |
1.3.6.1.4.1.485.3.5.5.1.1.23 | frameRelaySwitchedBackup | 0 | 0 | Defines the switched backup protocol used for dial backup. The range of this parameter is NONE or RACAL DTR-initiated. The defa… |
1.3.6.1.4.1.485.3.5.5.1.1.24 | frameRelaySwitchedLineWaitTimer | 0 | 0 | This parameter defines the maximum amount of time the FrameNode waits for the DAP to establish a dial connection before switching… |
1.3.6.1.4.1.485.3.5.5.1.1.25 | frameRelayDedLineWaitTimer | 0 | 0 | The FCC regulation for Autodialers requires that an Autodialer waits between successive dial operations. This parameter satisfies… |
1.3.6.1.4.1.485.3.5.5.1.1.26 | frameRelayCommittedBurst | 0 | 0 | This parameter specifies the maximum number of bits, during time interval Tc, the network agrees to accept under normal conditio… |
1.3.6.1.4.1.485.3.5.5.1.1.27 | frameRelayExcessBurst | 0 | 0 | This is the maximum number of uncommitted bits, during time interval Tc, the network accepts above the committed burst size Bc. W… |
1.3.6.1.4.1.485.3.5.5.1.1.28 | frameRelayBridgingProtocol | 0 | 0 | This parameter specifies the bridging protocol to be used over Frame Relay link. This parameter has no effect if bridging is not… |
1.3.6.1.4.1.485.3.5.5.1.1.29 | frameRelayProxyARP | 0 | 0 | This parameter defines whether PROXY ARP is enabled for F/R attached devices or not. Range of this parameter is ENABLED or DISAB… |
1.3.6.1.4.1.485.3.5.5.1.1.30 | frameRelaySecondDefaultGatewayAddress | 0 | 0 | Second Default gateway address to be used when sending responses on this interface. |
1.3.6.1.4.1.485.3.5.5.1.1.31 | frameRelayAlternateIPAddress | 0 | 0 | This is the Alternate IP Address for single port dial up connection. |
1.3.6.1.4.1.485.3.5.5.1.1.32 | frameRelayAlternateNetmask | 0 | 0 | This is the Alternate network mask for IP for single port dial up connecton. |
1.3.6.1.4.1.485.3.5.5.1.1.33 | frameRelayLLC2FrameFormat | 0 | 0 | This parameter specifies the LLC2 frame format to be used over Frame Relay link. The range of this parameter is Token Ring, Ethe… |
1.3.6.1.4.1.485.3.5.5.1.1.35 | frameRelayRestrictTerminateSessUsage | 0 | 0 | This parameter specifies whether terminated sessions are to follow spanning tree states or not over Frame Relay Link. The range o… |
1.3.6.1.4.1.485.3.5.5.1.1.36 | frameRelayRIPUpdtTimer | 0 | 0 | Defines frequency at which the RIP packets are sent over this interface. The range of this parameter is from 10 seconds to 180 s… |
1.3.6.1.4.1.485.3.5.5.1.1.37 | frameRelayRIPAge | 0 | 0 | Defines frequency at which the learned RIP entries are removed if not corresponding RIP update is received. The range of this pa… |
1.3.6.1.4.1.485.3.5.5.1.1.38 | frameRelaySAPUpdtTimer | 0 | 0 | Defines frequency at which the SAP packets are sent over this interface. The range of this parameter is from 10 seconds to 180 s… |
1.3.6.1.4.1.485.3.5.5.1.1.39 | frameRelaySAPAge | 0 | 0 | Defines frequency at which the learned SAP entries are removed if not corresponding SAP update is received. The range of this pa… |
1.3.6.1.4.1.485.3.5.5.1.1.40 | frameRelayRSM | 0 | 0 | The Routing Summary Information parameter indicates whether the routing summary information should be generated in the RIP on tha… |
1.3.6.1.4.1.485.3.5.5.1.1.41 | frameRelayARP | 0 | 0 | The ARP parameter indicates what format of ARP should be generated. Default value is 'Auto' |
1.3.6.1.4.1.485.3.5.5.1.1.42 | frameRelayCTS | 0 | 0 | Defines whether CTS is an input signal used to determine the port status. This parameter is applicable if clocking is set to exte… |
1.3.6.1.4.1.485.3.5.5.1.1.43 | frameRelayDCD | 0 | 0 | Defines whether DCD is required as input signal or ignored. This parameter is applicable if the clocking is set to external. For… |
1.3.6.1.4.1.485.3.5.5.1.1.44 | frameRelayDSR | 0 | 0 | Defines whether DSR is required as input signal or ignored. This parameter is applicable if the clocking is set to external. For… |
1.3.6.1.4.1.485.3.5.5.1.1.45 | frameRelayDTR | 0 | 0 | Defines whether DTR is required as input signal or ignored. This parameter is applicable if the clocking is set to internal. For… |
1.3.6.1.4.1.485.3.5.5.1.1.46 | frameRelayRTS | 0 | 0 | Defines whether RTS is an input signal to determine the port status. This parameter is applicable if the clocking is set to inter… |
1.3.6.1.4.1.485.3.5.5.1.1.47 | frameRelayReturnClock | 0 | 0 | Defines whether Return Clock (SCTE) is available as input signal or ignored. This parameter is applicable if the clocking is set … |