Measured in seconds, intervals of 5
T391 - Annex D
nT1 - LMI
The default value for this field is 5 seconds.
Parsed from file 3Com-linkconv.mib.txt
Company: None
Module: SYNC-RESEARCH-MIB
Measured in seconds, intervals of 5
T391 - Annex D
nT1 - LMI
The default value for this field is 5 seconds.
Parsed from file SYNC-RESEARCH-MIB.mib
Module: SYNC-RESEARCH-MIB
Vendor: Sync Research, Inc.
Module: SYNC-RESEARCH-MIB
[Automatically extracted from oidview.com]
frameRelayLinkPollingTimer OBJECT-TYPE SYNTAX INTEGER (5..30) ACCESS read-only STATUS mandatory DESCRIPTION "Measured in seconds, intervals of 5 T391 - Annex D nT1 - LMI The default value for this field is 5 seconds." ::= { frameRelayConfigEntry 7 }
frameRelayLinkPollingTimer OBJECT-TYPE SYNTAX INTEGER (5..30) ACCESS read-only STATUS mandatory DESCRIPTION "Measured in seconds, intervals of 5 T391 - Annex D nT1 - LMI The default value for this field is 5 seconds." ::= { frameRelayConfigEntry 7 }
OID | Name | Sub children | Sub Nodes Total | Description |
---|---|---|---|---|
1.3.6.1.4.1.485.3.5.5.1.1.1 | frameRelayConfigPortIndex | 0 | 0 | The port number that uniquely identifies this port. |
1.3.6.1.4.1.485.3.5.5.1.1.2 | frameRelayPortType | 0 | 0 | The Frame Relay port type. |
1.3.6.1.4.1.485.3.5.5.1.1.3 | frameRelayInitState | 0 | 0 | The initial state of the Frame Relay port. If configured for 'in-service', then the Frame Relay port will be brougt up automatica… |
1.3.6.1.4.1.485.3.5.5.1.1.4 | frameRelayClocking | 0 | 0 | Clocking source for this port. Setting 'internal' will cause the port to emulate a physical DCE, and setting external will cause t… |
1.3.6.1.4.1.485.3.5.5.1.1.5 | frameRelaySpeed | 0 | 0 | The ports speed in bits per second. The default value is 9600 bits per second. Speeds higher than 19200 are not supported on RS-23… |
1.3.6.1.4.1.485.3.5.5.1.1.6 | frameRelayLocalManagementProtocol | 0 | 0 | The ports management protocol type. Annex D = ANSI T1.617 Annex D LMI = Frame Relay Manufacturers LMI The default value is Annex D. |
1.3.6.1.4.1.485.3.5.5.1.1.8 | frameRelayFullStatusPollingCount | 0 | 0 | The number of polls that a full status poll is issued. N391 - Annex D nT1 - LMI The default value for this field is 6. |
1.3.6.1.4.1.485.3.5.5.1.1.9 | frameRelayT1Timer | 0 | 0 | The default LLC T1 timer value in seconds. T1 should be greater than T2 and less than Ti. Currently supported values are 1 to 25 … |
1.3.6.1.4.1.485.3.5.5.1.1.10 | frameRelayT2Timer | 0 | 0 | The default LLC T2 timer value in tenths of seconds. If configured for 0 then the T2 timer is disabled and an RR frame will be se… |
1.3.6.1.4.1.485.3.5.5.1.1.11 | frameRelayTiTimer | 0 | 0 | The default LLC Ti (inactivity) timer value in seconds. Ti should be greater than T1. Currently supported values are 2 to 50 secon… |
1.3.6.1.4.1.485.3.5.5.1.1.12 | frameRelayRxWindowSize | 0 | 0 | The default LLC receive window (N3) size. Note that this is not the same receive window as defined in IEEE 802.2 LLC. This is N3… |
1.3.6.1.4.1.485.3.5.5.1.1.13 | frameRelayTxWindowSize | 0 | 0 | The defalut LLC transmit window size. Current allowable values are 1-7. The default value for this field is 7. |
1.3.6.1.4.1.485.3.5.5.1.1.14 | frameRelayMaxRetries | 0 | 0 | The default LLC maximum number of retries (N2 value). The default value for this field is 15. |
1.3.6.1.4.1.485.3.5.5.1.1.15 | frameRelayNAUName | 0 | 0 | The NAU name of this port. The default value for this field is all blank (filled with ASCII space 0x20 characters). |
1.3.6.1.4.1.485.3.5.5.1.1.16 | frameRelayVirtualMACAddress | 0 | 0 | The F/R WAN is treated as a token ring. This address is used for communication with other bridges in the network. |
1.3.6.1.4.1.485.3.5.5.1.1.17 | frameRelayVirtualRingNumber | 0 | 0 | The F/R WAN is treated as a token ring. This is the ring number for the F/R network to which the port is attached. It must be a u… |
1.3.6.1.4.1.485.3.5.5.1.1.18 | frameRelayVirtualBridgeNumber | 0 | 0 | The F/R WAN is treated as a token ring. This variable only has significance if more than 1 F/R port is configured. The default va… |
1.3.6.1.4.1.485.3.5.5.1.1.19 | frameRelayIPAddress | 0 | 0 | This is the IP Address of this interface. |
1.3.6.1.4.1.485.3.5.5.1.1.20 | frameRelayNetworkMask | 0 | 0 | This is the network mask to be used on this interface. |
1.3.6.1.4.1.485.3.5.5.1.1.21 | frameRelayDefaultGatewayAddress | 0 | 0 | Default gateway address to be used when sending responses on this interface. |
1.3.6.1.4.1.485.3.5.5.1.1.22 | frameRelaySessSwitchThreshold | 0 | 0 | frameRelaySessSwitchthreshold |
1.3.6.1.4.1.485.3.5.5.1.1.23 | frameRelaySwitchedBackup | 0 | 0 | Defines the switched backup protocol used for dial backup. The range of this parameter is NONE or RACAL DTR-initiated. The defa… |
1.3.6.1.4.1.485.3.5.5.1.1.24 | frameRelaySwitchedLineWaitTimer | 0 | 0 | This parameter defines the maximum amount of time the FrameNode waits for the DAP to establish a dial connection before switching… |
1.3.6.1.4.1.485.3.5.5.1.1.25 | frameRelayDedLineWaitTimer | 0 | 0 | The FCC regulation for Autodialers requires that an Autodialer waits between successive dial operations. This parameter satisfies… |
1.3.6.1.4.1.485.3.5.5.1.1.26 | frameRelayCommittedBurst | 0 | 0 | This parameter specifies the maximum number of bits, during time interval Tc, the network agrees to accept under normal conditio… |
1.3.6.1.4.1.485.3.5.5.1.1.27 | frameRelayExcessBurst | 0 | 0 | This is the maximum number of uncommitted bits, during time interval Tc, the network accepts above the committed burst size Bc. W… |
1.3.6.1.4.1.485.3.5.5.1.1.28 | frameRelayBridgingProtocol | 0 | 0 | This parameter specifies the bridging protocol to be used over Frame Relay link. This parameter has no effect if bridging is not… |
1.3.6.1.4.1.485.3.5.5.1.1.29 | frameRelayProxyARP | 0 | 0 | This parameter defines whether PROXY ARP is enabled for F/R attached devices or not. Range of this parameter is ENABLED or DISAB… |
1.3.6.1.4.1.485.3.5.5.1.1.30 | frameRelaySecondDefaultGatewayAddress | 0 | 0 | Second Default gateway address to be used when sending responses on this interface. |
1.3.6.1.4.1.485.3.5.5.1.1.31 | frameRelayAlternateIPAddress | 0 | 0 | This is the Alternate IP Address for single port dial up connection. |
1.3.6.1.4.1.485.3.5.5.1.1.32 | frameRelayAlternateNetmask | 0 | 0 | This is the Alternate network mask for IP for single port dial up connecton. |
1.3.6.1.4.1.485.3.5.5.1.1.33 | frameRelayLLC2FrameFormat | 0 | 0 | This parameter specifies the LLC2 frame format to be used over Frame Relay link. The range of this parameter is Token Ring, Ethe… |
1.3.6.1.4.1.485.3.5.5.1.1.34 | frameRelayMultiflagSeparation | 0 | 0 | This parameter specifies whether the unit will insert more than one flag between frames. The range of this parameter is yes and … |
1.3.6.1.4.1.485.3.5.5.1.1.35 | frameRelayRestrictTerminateSessUsage | 0 | 0 | This parameter specifies whether terminated sessions are to follow spanning tree states or not over Frame Relay Link. The range o… |
1.3.6.1.4.1.485.3.5.5.1.1.36 | frameRelayRIPUpdtTimer | 0 | 0 | Defines frequency at which the RIP packets are sent over this interface. The range of this parameter is from 10 seconds to 180 s… |
1.3.6.1.4.1.485.3.5.5.1.1.37 | frameRelayRIPAge | 0 | 0 | Defines frequency at which the learned RIP entries are removed if not corresponding RIP update is received. The range of this pa… |
1.3.6.1.4.1.485.3.5.5.1.1.38 | frameRelaySAPUpdtTimer | 0 | 0 | Defines frequency at which the SAP packets are sent over this interface. The range of this parameter is from 10 seconds to 180 s… |
1.3.6.1.4.1.485.3.5.5.1.1.39 | frameRelaySAPAge | 0 | 0 | Defines frequency at which the learned SAP entries are removed if not corresponding SAP update is received. The range of this pa… |
1.3.6.1.4.1.485.3.5.5.1.1.40 | frameRelayRSM | 0 | 0 | The Routing Summary Information parameter indicates whether the routing summary information should be generated in the RIP on tha… |
1.3.6.1.4.1.485.3.5.5.1.1.41 | frameRelayARP | 0 | 0 | The ARP parameter indicates what format of ARP should be generated. Default value is 'Auto' |
1.3.6.1.4.1.485.3.5.5.1.1.42 | frameRelayCTS | 0 | 0 | Defines whether CTS is an input signal used to determine the port status. This parameter is applicable if clocking is set to exte… |
1.3.6.1.4.1.485.3.5.5.1.1.43 | frameRelayDCD | 0 | 0 | Defines whether DCD is required as input signal or ignored. This parameter is applicable if the clocking is set to external. For… |
1.3.6.1.4.1.485.3.5.5.1.1.44 | frameRelayDSR | 0 | 0 | Defines whether DSR is required as input signal or ignored. This parameter is applicable if the clocking is set to external. For… |
1.3.6.1.4.1.485.3.5.5.1.1.45 | frameRelayDTR | 0 | 0 | Defines whether DTR is required as input signal or ignored. This parameter is applicable if the clocking is set to internal. For… |
1.3.6.1.4.1.485.3.5.5.1.1.46 | frameRelayRTS | 0 | 0 | Defines whether RTS is an input signal to determine the port status. This parameter is applicable if the clocking is set to inter… |
1.3.6.1.4.1.485.3.5.5.1.1.47 | frameRelayReturnClock | 0 | 0 | Defines whether Return Clock (SCTE) is available as input signal or ignored. This parameter is applicable if the clocking is set … |