Determines whether loopback is enabled and what kind of loopback is enabled.
Options:
n/a (0): object is not applicable
none (1): Loopback is not enabled
local (2): Local loopback is enabled (return outbound frames to the originating
software layer without transmitting them)
remote (3): Remote loopback is enabled (forces the port to return (transmit)
any frame received on the line, and causes the port to deny communication
with any upper layer that requests service)
both (4):Both local and remote loopbacks are enabled.
isdn-uif-uif (5): ISDN loopback is enabled at U-Interface (forces TB1Q signal
from a remote transmitter to pass through the entire U-Interface Transceiver
before being transmitted back to the remote receiver)
isdn-uif-idl2 (6): ISDN loopback is enabled at IDL2 Controller (forces IDL2
Controller to take in B and D channel data on IDL RX pin and send it out on
IDL2 TX pin)
isdn-uif-framer (7): ISDN loopback is enabled at framer (forces B and D
channel data in on D_in pin and M channel data in on SCP which together
undergo framing and deframing functions before B and D channel data go out
D_out pin and M channel data go out SCP)
isdn-uif-external (8): ISDN loopback is enabled at external line (forces TB1Q
signal coming in on D_in pin to pass through Tx Driver pins, the U-Interface
circuit and Rx input pins before recovering it and sending it out the D_out
pin)
Default Value: none
Parsed from file CXBOPIO.MIB.txt
Company: None
Module: CXBOPIO-MIB
Determines whether loopback is enabled and what kind of loopback is enabled.
Options:
n/a (0): object is not applicable
none (1): Loopback is not enabled
local (2): Local loopback is enabled (return outbound frames to the originating
software layer without transmitting them)
remote (3): Remote loopback is enabled (forces the port to return (transmit)
any frame received on the line, and causes the port to deny communication
with any upper layer that requests service)
both (4):Both local and remote loopbacks are enabled.
isdn-uif-uif (5): ISDN loopback is enabled at U-Interface (forces TB1Q signal
from a remote transmitter to pass through the entire U-Interface Transceiver
before being transmitted back to the remote receiver)
isdn-uif-idl2 (6): ISDN loopback is enabled at IDL2 Controller (forces IDL2
Controller to take in B and D channel data on IDL RX pin and send it out on
IDL2 TX pin)
isdn-uif-framer (7): ISDN loopback is enabled at framer (forces B and D
channel data in on D-in pin and M channel data in on SCP which together
undergo framing and deframing functions before B and D channel data go out
D-out pin and M channel data go out SCP)
isdn-uif-external (8): ISDN loopback is enabled at external line (forces TB1Q
signal coming in on D-in pin to pass through Tx Driver pins, the U-Interface
circuit and Rx input pins before recovering it and sending it out the D-out
pin)
Default Value: none
Parsed from file CXBOPIO-MIB.mib
Module: CXBOPIO-MIB
Vendor: Memotec Communications
Module: CXBOPIO-MIB
[Automatically extracted from oidview.com]
bopSapOprPortLoopback OBJECT-TYPE SYNTAX INTEGER { none (1), local (2), remote (3), both (4), isdn-uif-uif (5), isdn-uif-idl2 (6), isdn-uif-framer (7), isdn-uif-external (8) } ACCESS read-only STATUS mandatory DESCRIPTION "Determines whether loopback is enabled and what kind of loopback is enabled. Options: n/a (0): object is not applicable none (1): Loopback is not enabled local (2): Local loopback is enabled (return outbound frames to the originating software layer without transmitting them) remote (3): Remote loopback is enabled (forces the port to return (transmit) any frame received on the line, and causes the port to deny communication with any upper layer that requests service) both (4):Both local and remote loopbacks are enabled. isdn-uif-uif (5): ISDN loopback is enabled at U-Interface (forces TB1Q signal from a remote transmitter to pass through the entire U-Interface Transceiver before being transmitted back to the remote receiver) isdn-uif-idl2 (6): ISDN loopback is enabled at IDL2 Controller (forces IDL2 Controller to take in B and D channel data on IDL RX pin and send it out on IDL2 TX pin) isdn-uif-framer (7): ISDN loopback is enabled at framer (forces B and D channel data in on D_in pin and M channel data in on SCP which together undergo framing and deframing functions before B and D channel data go out D_out pin and M channel data go out SCP) isdn-uif-external (8): ISDN loopback is enabled at external line (forces TB1Q signal coming in on D_in pin to pass through Tx Driver pins, the U-Interface circuit and Rx input pins before recovering it and sending it out the D_out pin) Default Value: none" ::= { bopSapOprEntry 28 }
bopSapOprPortLoopback OBJECT-TYPE SYNTAX INTEGER { none (1), local (2), remote (3), both (4), isdn-uif-uif (5), isdn-uif-idl2 (6), isdn-uif-framer (7), isdn-uif-external (8) } ACCESS read-only STATUS mandatory DESCRIPTION "Determines whether loopback is enabled and what kind of loopback is enabled. Options: n/a (0): object is not applicable none (1): Loopback is not enabled local (2): Local loopback is enabled (return outbound frames to the originating software layer without transmitting them) remote (3): Remote loopback is enabled (forces the port to return (transmit) any frame received on the line, and causes the port to deny communication with any upper layer that requests service) both (4):Both local and remote loopbacks are enabled. isdn-uif-uif (5): ISDN loopback is enabled at U-Interface (forces TB1Q signal from a remote transmitter to pass through the entire U-Interface Transceiver before being transmitted back to the remote receiver) isdn-uif-idl2 (6): ISDN loopback is enabled at IDL2 Controller (forces IDL2 Controller to take in B and D channel data on IDL RX pin and send it out on IDL2 TX pin) isdn-uif-framer (7): ISDN loopback is enabled at framer (forces B and D channel data in on D-in pin and M channel data in on SCP which together undergo framing and deframing functions before B and D channel data go out D-out pin and M channel data go out SCP) isdn-uif-external (8): ISDN loopback is enabled at external line (forces TB1Q signal coming in on D-in pin to pass through Tx Driver pins, the U-Interface circuit and Rx input pins before recovering it and sending it out the D-out pin) Default Value: none" ::= { bopSapOprEntry 28 }
OID | Name | Sub children | Sub Nodes Total | Description |
---|---|---|---|---|
1.3.6.1.4.1.495.2.1.6.36.1.1.1 | bopSapOprNumber | 0 | 0 | Defines the SAP ID using 2,3 or 4 digits. The first digit (A) is the slot #, the second digit (B) is the port #, and the remaini… |
1.3.6.1.4.1.495.2.1.6.36.1.1.2 | bopSapOprAlias | 0 | 0 | Determines the active textual name uniquely identifying this port SAP. Range of Values: 0 - 16 alphanumeric characters beginning… |
1.3.6.1.4.1.495.2.1.6.36.1.1.3 | bopSapOprProtocol | 0 | 0 | Determines if the port is HDLC or Bisync. Only HDLC is supported by ISDN and T1/E1 ports. Indicates in the operative configuration… |
1.3.6.1.4.1.495.2.1.6.36.1.1.5 | bopSapOprPortClockSource | 0 | 0 | Determines the active data clock source for this port. Options: internal (1): Tx and Rx clocks are internally generated external (… |
1.3.6.1.4.1.495.2.1.6.36.1.1.6 | bopSapOprPortSpeed | 0 | 0 | Determines the input and output speed in bits per second for this port. Note: Meaningful only if 'bopSapOprPortClockSource' is '… |
1.3.6.1.4.1.495.2.1.6.36.1.1.7 | bopSapOprPortDuplex | 0 | 0 | Determines whether this port is communicating simultaneously in both directions (full-duplex) or alternates between directions (… |
1.3.6.1.4.1.495.2.1.6.36.1.1.8 | bopSapOprPortMaxFrameSize | 0 | 0 | Determines the active maximum frame size supported by this port. Ranges of Values: 32-9000 Default Value: 1,600 (512 for ISDN) |
1.3.6.1.4.1.495.2.1.6.36.1.1.9 | bopSapOprPortDataEncoding | 0 | 0 | Determines the active data formatting and encoding used by this port. Options: n/a (0): object is not applicable nrz (1): NRZ (loc… |
1.3.6.1.4.1.495.2.1.6.36.1.1.10 | bopSapOprPortIdleCondition | 0 | 0 | Determines the active idle line condition supported by this port. Options: flags (1): flags marks (2): marks as400 (3): AS400 Defaul… |
1.3.6.1.4.1.495.2.1.6.36.1.1.11 | bopSapOprPortPreAmbleLength | 0 | 0 | Determines the minimum number of flags or sync pairs that will be inserted between frames by the port's transmitter. For HDLC fra… |
1.3.6.1.4.1.495.2.1.6.36.1.1.12 | bopSapOprPortFlagSharing | 0 | 0 | Determines whether back-to-back Tx frames share opening and closing flag. This value is meaningful only if 'bopSapAdmPortPreAmbl… |
1.3.6.1.4.1.495.2.1.6.36.1.1.13 | bopSapOprPortFilterMask | 0 | 0 | Indicates which bits of the 8-bit HDLC address are being used for address filtering on this port (CX900 or USIO only). Note: When… |
1.3.6.1.4.1.495.2.1.6.36.1.1.14 | bopSapOprPortFilterAddress1 | 0 | 0 | Indicates one of four 8-bit addresses used for address filtering (CX900 or USIO only). Ranges of Values: 0 - 255 Default Value: 126 |
1.3.6.1.4.1.495.2.1.6.36.1.1.15 | bopSapOprPortFilterAddress2 | 0 | 0 | Indicates one of four 8-bit addresses used for address filtering (CX900 or USIO only). Ranges of Values: 0 - 255 Default Value: 126 |
1.3.6.1.4.1.495.2.1.6.36.1.1.16 | bopSapOprPortFilterAddress3 | 0 | 0 | Indicates one of four 8-bit addresses used for address filtering (CX900 or USIO only). Ranges of Values: 0 - 255 Default Value: 126 |
1.3.6.1.4.1.495.2.1.6.36.1.1.17 | bopSapOprPortFilterAddress4 | 0 | 0 | Indicates one of four 8-bit addresses used for address filtering (CX900 or USIO only). Ranges of Values: 0 - 255 Default Value: 126 |
1.3.6.1.4.1.495.2.1.6.36.1.1.18 | bopSapOprPortCrc | 0 | 0 | Determines which algorithm is being used for error detection. Options: crc-ccitt (1): CRC-ITU-T (uses X15+X12+X5+1 polynomial; IT… |
1.3.6.1.4.1.495.2.1.6.36.1.1.19 | bopSapOprPortDtrUpTimer | 0 | 0 | Determines the time in seconds that the port must wait for DCD (DTR if DCE) after raising DTR (DCD if DCE) to determine if a con… |
1.3.6.1.4.1.495.2.1.6.36.1.1.20 | bopSapOprPortTxWindow | 0 | 0 | Determines the active maximum number of buffers that may be queued onto the port driver (for transmission) by the associated upp… |
1.3.6.1.4.1.495.2.1.6.36.1.1.21 | bopSapOprPortDialMode | 0 | 0 | Identifies the operation mode when setting up connections. Options: n/a (0): object is not applicable dial-in-only (1): Only acce… |
1.3.6.1.4.1.495.2.1.6.36.1.1.29 | bopSapOprPortSignalSamplingPeriod | 0 | 0 | Determines the active sampling period in 100 millisecond increments that this port uses to sample signals. This object has no me… |
1.3.6.1.4.1.495.2.1.6.36.1.1.30 | bopSapOprPortDcdDtrSignalSamples | 0 | 0 | Determines the active number of sampling periods that this port must wait before validating DCD (DTR if DCE). This object has no … |
1.3.6.1.4.1.495.2.1.6.36.1.1.31 | bopSapOprPortCtsRtsSignalSamples | 0 | 0 | Determines the active number of sampling periods that this port must wait before validating CTS (RTS if DCE). This object has no … |
1.3.6.1.4.1.495.2.1.6.36.1.1.32 | bopSapOprPortDsrDrsSignalSamples | 0 | 0 | Determines the active number of sampling periods that this port must wait before validating DRS (DSR if DCE). This object has no … |
1.3.6.1.4.1.495.2.1.6.36.1.1.33 | bopSapOprPortTmLlSignalSamples | 0 | 0 | Determines the active number of sampling periods that this port must wait before validating TM (LL if DCE). This object has no me… |
1.3.6.1.4.1.495.2.1.6.36.1.1.34 | bopSapOprPortRiRlSignalSamples | 0 | 0 | Determines the active number of sampling periods that this port must wait before validating RI (RL if DCE). This object has no me… |
1.3.6.1.4.1.495.2.1.6.36.1.1.35 | bopSapOprPortStatisticsTimer | 0 | 0 | Determines the active period in seconds during which BOP performance statistics are measured. Note: If set to zero, BOP performan… |
1.3.6.1.4.1.495.2.1.6.36.1.1.36 | bopSapOprPortCarrierAction | 0 | 0 | Determines if the port driver informs it's associated upper layer that service is no longer available following loss of DCD if D… |
1.3.6.1.4.1.495.2.1.6.36.1.1.37 | bopSapOprPortDataGenerator | 0 | 0 | Determines whether this port acts as an internal data generator. Options: n/a (0): object is not applicable disabled (1): port is … |
1.3.6.1.4.1.495.2.1.6.36.1.1.38 | bopSapOprPortGenFrames | 0 | 0 | Determines the number of frames that the port configured as an internal data generator will generate at one time. Ranges of Value… |
1.3.6.1.4.1.495.2.1.6.36.1.1.39 | bopSapOprPortGenFrameSize | 0 | 0 | Determines the size in bytes of internally generated frames (excluding flags). Ranges of Values: 2 - 65,535 Note: When set to zer… |
1.3.6.1.4.1.495.2.1.6.36.1.1.40 | bopSapOprPortGenFrameHeader | 0 | 0 | Determines the 16-bit header that is inserted in the first two octets after the opening flag of each internally generated frame.… |
1.3.6.1.4.1.495.2.1.6.36.1.1.41 | bopSapOprPortThreshBandwidth | 0 | 0 | Determines the value of the minimum critical bandwidth that determines whether Frame Relay should filter certain restricted type… |
1.3.6.1.4.1.495.2.1.6.36.1.1.42 | bopSapOprPortActualSpeed | 0 | 0 | Determines the actual calculated output speed in bits per second of the port. Ranges of Values: 375 - 2,048,000 Default Value: 0 |
1.3.6.1.4.1.495.2.1.6.36.1.1.43 | bopSapOprCodeSet | 0 | 0 | Indicates the code used to communicate with the Bisync device. Options: (0) N/A: object is not applicable (1) EBCDIC code set (2) A… |
1.3.6.1.4.1.495.2.1.6.36.1.1.44 | bopSapOprParity | 0 | 0 | Indicates the parity used to communicate with the Bisync device Options: (0) N/A: Object is not applicable (1) none: No parity (… |
1.3.6.1.4.1.495.2.1.6.36.1.1.47 | bopOprPortTrap | 0 | 0 | Determines whether this port produces a 'bopPortStatusChange' trap which can be retrieved by SNMP network management. Options: dis… |
1.3.6.1.4.1.495.2.1.6.36.1.1.48 | bopOprTxClockTrap | 0 | 0 | Determines whether this port produces a 'bopTxClockStatusChange' trap which can be retrieved by SNMP network management. Options:… |
1.3.6.1.4.1.495.2.1.6.36.1.1.52 | bopOprControlLine | 0 | 0 | Controls the state of the port. Options: forceDown (1): forces the port into a 'down' state forceUp (2): forces the port into an '… |
1.3.6.1.4.1.495.2.1.6.36.1.1.53 | bopOprControlStats | 0 | 0 | Specifies that port statistics are to be cleared. Options: clearSapStats (1): clears port statistics Default Value: none |
1.3.6.1.4.1.495.2.1.6.36.1.1.55 | bopStatOprPortType | 0 | 0 | Indicates the type of hardware strapping for the port. Options: unknown (1): unknown strapping dte (2): DTE strapping dce (3): DC… |
1.3.6.1.4.1.495.2.1.6.36.1.1.56 | bopStatOprPortInterfaceType | 0 | 0 | Indicates the type of hardware interface of the port. Options: unknown (1) rs232d (2): V.24 v35 (3): V.35 x21(4): X.21 v34 (5): V.34 … |
1.3.6.1.4.1.495.2.1.6.36.1.1.57 | bopStatOprPortState | 0 | 0 | Indicates the state of availability of the port. Options: portUp (1): port is up portDown (2): port is down portShutDown (3): port … |
1.3.6.1.4.1.495.2.1.6.36.1.1.61 | bopStatOprTxClockState | 0 | 0 | Indicates the state availability of the transmit clock. Options: txClockDown (1): transmit clock is down txClockUp (2): transmit c… |
1.3.6.1.4.1.495.2.1.6.36.1.1.62 | bopStatOprDCDState | 0 | 0 | Indicates the state of the DCD signal. Options: unknown (1): DCD signal is in unknown state because hardware is not present inacti… |
1.3.6.1.4.1.495.2.1.6.36.1.1.63 | bopStatOprDTRState | 0 | 0 | Indicates the state of the DTR signal. Options: unknown (1): DTR signal is in unknown state because hardware is not present inacti… |
1.3.6.1.4.1.495.2.1.6.36.1.1.64 | bopStatOprRTSState | 0 | 0 | Indicates the state of the RTS signal. Options: unknown (1): RTS signal is in unknown state because hardware is not present inacti… |
1.3.6.1.4.1.495.2.1.6.36.1.1.65 | bopStatOprCTSState | 0 | 0 | Indicates the state of the CTS signal. Options: unknown (1): CTS signal is in unknown state because hardware is not present inacti… |
1.3.6.1.4.1.495.2.1.6.36.1.1.66 | bopStatOprDSRState | 0 | 0 | Indicates the state of the DSR signal. Options: unknown (1): DSR signal is in unknown state because hardware is not present inacti… |
1.3.6.1.4.1.495.2.1.6.36.1.1.67 | bopStatOprDRSState | 0 | 0 | Indicates the state of the DRS signal. Options: unknown (1): DRS signal is in unknown state because hardware is not present inacti… |
1.3.6.1.4.1.495.2.1.6.36.1.1.68 | bopStatOprTMState | 0 | 0 | Indicates the state of the TM signal. Options: unknown (1): TM signal is in unknown state because hardware is not present inactive… |
1.3.6.1.4.1.495.2.1.6.36.1.1.69 | bopStatOprLLState | 0 | 0 | Indicates the state of the LL signal. Options: unknown (1): LL signal is in unknown state because hardware is not present inactive… |
1.3.6.1.4.1.495.2.1.6.36.1.1.70 | bopStatOprRIState | 0 | 0 | Indicates the state of the RI signal. Options: unknown (1): RI signal is in unknown state because hardware is not present inactive… |
1.3.6.1.4.1.495.2.1.6.36.1.1.71 | bopStatOprRLState | 0 | 0 | Indicates the state of the RL signal. Options: unknown (1): RL signal is in unknown state because hardware is not present inactive… |
1.3.6.1.4.1.495.2.1.6.36.1.1.75 | bopStatOprTxFrames | 0 | 0 | Indicates the total number of Tx frames since statistics were last reset. Ranges of Values: 0 - 4,294,967,295 Default Value: none |
1.3.6.1.4.1.495.2.1.6.36.1.1.76 | bopStatOprRxFrames | 0 | 0 | Indicates the total number of Rx frames since statistics were last reset. Ranges of Values: 0 - 4,294,967,295 Default Value: none |
1.3.6.1.4.1.495.2.1.6.36.1.1.77 | bopStatOprLocalLoopbackFrames | 0 | 0 | Indicates the total number of frames locally looped back since statistics were last reset. Ranges of Values: 0 - 4,294,967,295 Def… |
1.3.6.1.4.1.495.2.1.6.36.1.1.78 | bopStatOprTxBps | 0 | 0 | Indicates the number of transmitted bits divided by the number of seconds set in 'bopSapOprPortStatisticsTimer'. Ranges of Values… |
1.3.6.1.4.1.495.2.1.6.36.1.1.79 | bopStatOprRxBps | 0 | 0 | Indicates the number of received bits divided by the number of seconds set in 'bopSapOprPortStatisticsTimer'. Ranges of Values: 0… |
1.3.6.1.4.1.495.2.1.6.36.1.1.80 | bopStatOprTxBpsMax | 0 | 0 | Indicates the highest number of bits per second transmitted since statistics were last reset. Ranges of Values: 0 - 4,294,967,295… |
1.3.6.1.4.1.495.2.1.6.36.1.1.81 | bopStatOprRxBpsMax | 0 | 0 | Indicates the highest number of bits per second received since statistics were last reset. Ranges of Values: 0 - 4,294,967,295 Def… |
1.3.6.1.4.1.495.2.1.6.36.1.1.82 | bopStatOprTxFps | 0 | 0 | Indicates the number of transmitted frames divided by the number of seconds set in 'bopSapOprPortStatisticsTimer'. Ranges of Valu… |
1.3.6.1.4.1.495.2.1.6.36.1.1.83 | bopStatOprRxFps | 0 | 0 | Indicates the number of received frames divided by the number of seconds set in 'bopSapOprPortStatisticsTimer'. Ranges of Values:… |
1.3.6.1.4.1.495.2.1.6.36.1.1.84 | bopStatOprTxFpsMax | 0 | 0 | Indicates the highest number of frames per second transmitted since statistics were last reset. Ranges of Values: 0 - 4,294,967,2… |
1.3.6.1.4.1.495.2.1.6.36.1.1.85 | bopStatOprRxFpsMax | 0 | 0 | Indicates the highest number of frames per second received since statistics were last reset. Ranges of Values: 0 - 4,294,967,295 D… |
1.3.6.1.4.1.495.2.1.6.36.1.1.86 | bopStatOprTxUnderrunFrames | 0 | 0 | Indicates the total number of underrun frames that have been unsuccessfully transmitted since statistics were last reset. Ranges … |
1.3.6.1.4.1.495.2.1.6.36.1.1.87 | bopStatOprTxCtsLostFrames | 0 | 0 | Indicates the total number of frames unsuccessfully transmitted in half-duplex because CTS was dropped during transmission. Range… |
1.3.6.1.4.1.495.2.1.6.36.1.1.88 | bopStatOprTxBadStateDiscards | 0 | 0 | Indicates the total number of frames discarded since statistics were last reset, due to a request for frame transmission while t… |
1.3.6.1.4.1.495.2.1.6.36.1.1.89 | bopStatOprTxResetDiscards | 0 | 0 | Indicates the total number of frames discarded since statistics were last reset, due to a management request for a line reset. Ra… |
1.3.6.1.4.1.495.2.1.6.36.1.1.90 | bopStatOprTxSysCongestionDiscards | 0 | 0 | Indicates the total number of frames discarded since statistics were last reset, due to system congestion. Ranges of Values: 0 - … |
1.3.6.1.4.1.495.2.1.6.36.1.1.91 | bopStatOprTxInvWinDiscards | 0 | 0 | Indicates the total number of frames discarded since statistics were last reset, due to the transmit window being exceeded. Range… |
1.3.6.1.4.1.495.2.1.6.36.1.1.92 | bopStatOprTxInvRLpbkWinDiscards | 0 | 0 | Indicates the total number of frames discarded since statistics were last reset, due to the transmit window being exceeded while… |
1.3.6.1.4.1.495.2.1.6.36.1.1.98 | bopStatOprRxBadCrcFrames | 0 | 0 | Indicates the total number of bad CRC frames received since statistics were last reset. Ranges of Values: 0 - 65,535 Default Value… |
1.3.6.1.4.1.495.2.1.6.36.1.1.99 | bopStatOprRxAbortedFrames | 0 | 0 | Indicates the total number of aborted frames received since statistics were last reset. Note: A frame is aborted when the port's … |
1.3.6.1.4.1.495.2.1.6.36.1.1.100 | bopStatOprRxNonIntegralBitFrames | 0 | 0 | Indicates the total number of frames received since statistics were last reset, that did not have eight bits per byte. Note: Non-… |
1.3.6.1.4.1.495.2.1.6.36.1.1.101 | bopStatOprRxLongFrames | 0 | 0 | Indicates the total number of long frames received since statistics were last reset. Note: A long frame is counted each time a re… |
1.3.6.1.4.1.495.2.1.6.36.1.1.102 | bopStatOprRxOverrunFrames | 0 | 0 | Indicates the total number of overrun frames received since statistics were last reset. Note: An overrun indicates that a frame's … |
1.3.6.1.4.1.495.2.1.6.36.1.1.103 | bopStatOprRxCdLostFrames | 0 | 0 | Indicates the total number of frames received with DCD loss in half-duplex by the port. Ranges of Values: 0 - 65, 535 Default Valu… |
1.3.6.1.4.1.495.2.1.6.36.1.1.104 | bopStatOprRxBadStateDiscards | 0 | 0 | Indicates the total number of frames discarded since statistics were last reset, because BOP software layer was not bound to oth… |
1.3.6.1.4.1.495.2.1.6.36.1.1.105 | bopStatOprRxBusyDiscards | 0 | 0 | Indicates the total number of frames discarded since statistics were last reset, due to a lack of receive buffers. Ranges of Valu… |
1.3.6.1.4.1.495.2.1.6.36.1.1.109 | bopStatOprPortStateChanges | 0 | 0 | Indicates the total number of times the port has moved from one state to another since statistics were last reset. Ranges of Valu… |
1.3.6.1.4.1.495.2.1.6.36.1.1.110 | bopStatOprTxClockStateChanges | 0 | 0 | Indicates the total number of times that 'bopStatOprTxClockState' has moved from one state to another since were last reset. Rang… |
1.3.6.1.4.1.495.2.1.6.36.1.1.111 | bopStatOprDCDStateChanges | 0 | 0 | Indicates the total number of times DCD has moved from one state to another since statistics were last reset. Ranges of Values: 0… |
1.3.6.1.4.1.495.2.1.6.36.1.1.112 | bopStatOprDTRStateChanges | 0 | 0 | Indicates the total number of times DTR has moved from one state to another since statistics were last reset. Ranges of Values: 0… |
1.3.6.1.4.1.495.2.1.6.36.1.1.113 | bopStatOprRTSStateChanges | 0 | 0 | Indicates the total number of times RTS has moved from one state to another since statistics were last reset. Ranges of Values: 0… |
1.3.6.1.4.1.495.2.1.6.36.1.1.114 | bopStatOprCTSStateChanges | 0 | 0 | Indicates the total number of times CTS has moved from one state to another since statistics were last reset. Ranges of Values: 0… |
1.3.6.1.4.1.495.2.1.6.36.1.1.115 | bopStatOprDSRStateChanges | 0 | 0 | Indicates the total number of times DSR has moved from one state to another since statistics were last reset. Ranges of Values: 0… |
1.3.6.1.4.1.495.2.1.6.36.1.1.116 | bopStatOprDRSStateChanges | 0 | 0 | Indicates the total number of times DRS has moved from one state to another since statistics were last reset. Ranges of Values: 0… |
1.3.6.1.4.1.495.2.1.6.36.1.1.117 | bopStatOprTMStateChanges | 0 | 0 | Indicates the total number of times TM has moved from one state to another since statistics were last reset. Ranges of Values: 0 … |
1.3.6.1.4.1.495.2.1.6.36.1.1.118 | bopStatOprLLStateChanges | 0 | 0 | Indicates the total number of times LL has moved from one state to another since statistics were last reset. Ranges of Values: 0 … |
1.3.6.1.4.1.495.2.1.6.36.1.1.119 | bopStatOprRIStateChanges | 0 | 0 | Indicates the total number of times RI has moved from one state to another since statistics were last reset. Ranges of Values: 0 … |
1.3.6.1.4.1.495.2.1.6.36.1.1.120 | bopStatOprRLStateChanges | 0 | 0 | Indicates the total number of times RL has moved from one state to another since statistics were last reset. Ranges of Values: 0 … |
1.3.6.1.4.1.495.2.1.6.36.1.1.121 | bopStatOprPortResets | 0 | 0 | Indicates the total number of port resets that have occurred at the port since statistics were last reset. Ranges of Values: 0 - … |
1.3.6.1.4.1.495.2.1.6.36.1.1.123 | bopStatOprRxGenError | 0 | 0 | Indicates the total number of frames received in error since statistics were last reset, while 'bopSapOprPortDataGenerator' was … |