Determines the active number of sampling periods that this port must wait
before validating TM (LL if DCE).
This object has no meaning in ISDN connections.
Ranges of Values: 1-30
Default Value: 3
Configuration Changed: administrative
Parsed from file CXBOPIO.MIB.txt
Company: None
Module: CXBOPIO-MIB
Determines the active number of sampling periods that this port must wait
before validating TM (LL if DCE).
This object has no meaning in ISDN connections.
Ranges of Values: 1-30
Default Value: 3
Configuration Changed: administrative
Parsed from file CXBOPIO-MIB.mib
Module: CXBOPIO-MIB
Vendor: Memotec Communications
Module: CXBOPIO-MIB
[Automatically extracted from oidview.com]
bopSapAdmPortTmLlSignalSamples OBJECT-TYPE SYNTAX INTEGER (1..30) ACCESS read-write STATUS mandatory DESCRIPTION "Determines the active number of sampling periods that this port must wait before validating TM (LL if DCE). This object has no meaning in ISDN connections. Ranges of Values: 1-30 Default Value: 3 Configuration Changed: administrative " DEFVAL { 3 } ::= { bopSapAdmEntry 33 }
bopSapAdmPortTmLlSignalSamples OBJECT-TYPE SYNTAX INTEGER (1..30) ACCESS read-write STATUS mandatory DESCRIPTION "Determines the active number of sampling periods that this port must wait before validating TM (LL if DCE). This object has no meaning in ISDN connections. Ranges of Values: 1-30 Default Value: 3 Configuration Changed: administrative " DEFVAL { 3 } ::= { bopSapAdmEntry 33 }
OID | Name | Sub children | Sub Nodes Total | Description |
---|---|---|---|---|
1.3.6.1.4.1.495.2.1.6.36.2.1.1 | bopSapAdmNumber | 0 | 0 | Defines the SAP ID using 2,3 or 4 digits. The first digit (A) is the slot #, the second digit (B) is the port #, and the remaini… |
1.3.6.1.4.1.495.2.1.6.36.2.1.2 | bopSapAdmAlias | 0 | 0 | Determines the textual name uniquely identifying this SAP in the BOP Driver software layer. Ranges of Values: 0-16 alphanumeric c… |
1.3.6.1.4.1.495.2.1.6.36.2.1.3 | bopSapAdmProtocol | 0 | 0 | Determines if the port is HDLC or Bisync. Only HDLC is supported by ISDN and T1/E1 ports. Indicates in the operative configuration… |
1.3.6.1.4.1.495.2.1.6.36.2.1.5 | bopSapAdmPortClockSource | 0 | 0 | Determines the bit-rate clock source of the port. Options: internal (1): Tx and Rx clocks are internally generated external (2): T… |
1.3.6.1.4.1.495.2.1.6.36.2.1.6 | bopSapAdmPortSpeed | 0 | 0 | Indicates the input and output speed in bits per second of the port. Note: This value is meaningful only if 'bopSapAdmPortClockSo… |
1.3.6.1.4.1.495.2.1.6.36.2.1.7 | bopSapAdmPortDuplex | 0 | 0 | Determines whether the port communicates simultaneously in both directions (full-duplex) or alternates between directions (half-… |
1.3.6.1.4.1.495.2.1.6.36.2.1.8 | bopSapAdmPortMaxFrameSize | 0 | 0 | Determines the maximum frame size supported by the port. Ranges of Values: 32-9000 Default Value: 1,600 (512 for ISDN) Configurati… |
1.3.6.1.4.1.495.2.1.6.36.2.1.9 | bopSapAdmPortDataEncoding | 0 | 0 | Determines the data formatting and encoding used by the port. Options: nrz (1): NRZ (locked for ISDN 'D' channel; ISDN 'B' channe… |
1.3.6.1.4.1.495.2.1.6.36.2.1.10 | bopSapAdmPortIdleCondition | 0 | 0 | Determines the idle line condition supported by the port. Options: flags (1): flags marks (2): marks as400 (3): AS400 Default Value:… |
1.3.6.1.4.1.495.2.1.6.36.2.1.11 | bopSapAdmPortPreAmbleLength | 0 | 0 | Determines the minimum number of flags or sync pairs that will be inserted between frames by the port's transmitter. For HDLC fra… |
1.3.6.1.4.1.495.2.1.6.36.2.1.12 | bopSapAdmPortFlagSharing | 0 | 0 | Determines whether back-to-back transmit frames will have a flag in common This value is meaningful only if 'bopSapAdmPortPreAmb… |
1.3.6.1.4.1.495.2.1.6.36.2.1.13 | bopSapAdmPortFilterMask | 0 | 0 | Determines which bits of the 8-bit HDLC address will be used for address filtering. Note: When a bit is set to '1', the position o… |
1.3.6.1.4.1.495.2.1.6.36.2.1.14 | bopSapAdmPortFilterAddress1 | 0 | 0 | Determines one of four 8-bit addresses used for address filtering. Ranges of Values: 0-255 Default Value: 126 Configuration Change… |
1.3.6.1.4.1.495.2.1.6.36.2.1.15 | bopSapAdmPortFilterAddress2 | 0 | 0 | Determines one of four 8-bit addresses used for address filtering. Ranges of Values: 0-255 Default Value: 126 Configuration Change… |
1.3.6.1.4.1.495.2.1.6.36.2.1.16 | bopSapAdmPortFilterAddress3 | 0 | 0 | Determines one of four 8-bit addresses used for address filtering. Ranges of Values: 0-255 Default Value: 126 Configuration Change… |
1.3.6.1.4.1.495.2.1.6.36.2.1.17 | bopSapAdmPortFilterAddress4 | 0 | 0 | Determines one of four 8-bit addresses used for address filtering. Ranges of Values: 0-255 Default Value: 126 Configuration Change… |
1.3.6.1.4.1.495.2.1.6.36.2.1.18 | bopSapAdmPortCrc | 0 | 0 | Determines which algorithm is used for error detection. Options: crc-ccitt (1): CRC-ITU-T (uses X15+X12+X5+1 polynomial; ITU-T fo… |
1.3.6.1.4.1.495.2.1.6.36.2.1.19 | bopSapAdmPortDtrUpTimer | 0 | 0 | Determines the time in seconds that the port must wait for DCD (DTR if DCE) after raising DTR (DCD if DCE) to determine if a con… |
1.3.6.1.4.1.495.2.1.6.36.2.1.20 | bopSapAdmPortTxWindow | 0 | 0 | Determines the maximum number of buffers that may be queued onto the port driver (for transmission) by the associated upper laye… |
1.3.6.1.4.1.495.2.1.6.36.2.1.21 | bopSapAdmPortThreshBandwidth | 0 | 0 | Determines the value of the minimum critical bandwidth that will determine whether Frame Relay should filter certain restricted … |
1.3.6.1.4.1.495.2.1.6.36.2.1.22 | bopSapAdmPortDialMode | 0 | 0 | Identifies the operation mode when setting up connections. Options: dial-in-only (1): Only accept incoming calls; Will not make… |
1.3.6.1.4.1.495.2.1.6.36.2.1.28 | bopSapAdmPortLoopback | 0 | 0 | Determines whether loopback is enabled and what kind of loopback is enabled. Options: none (1): Loopback is not enabled local (2)… |
1.3.6.1.4.1.495.2.1.6.36.2.1.29 | bopSapAdmPortSignalSamplingPeriod | 0 | 0 | Determines the sampling period in 100 millisecond increments used to sample detectable signals. Ranges of Values: 3-100 (locked a… |
1.3.6.1.4.1.495.2.1.6.36.2.1.30 | bopSapAdmPortDcdDtrSignalSamples | 0 | 0 | Determines the active number of sampling periods that this port must wait before validating DCD (DTR if DCE). This object has no … |
1.3.6.1.4.1.495.2.1.6.36.2.1.31 | bopSapAdmPortCtsRtsSignalSamples | 0 | 0 | Determines the active number of sampling periods that this port must wait before validating CTS (RTS if DCE). This object has no … |
1.3.6.1.4.1.495.2.1.6.36.2.1.32 | bopSapAdmPortDsrDrsSignalSamples | 0 | 0 | Determines the active number of sampling periods that this port must wait before validating DSR (DRS if DCE). This object has no … |
1.3.6.1.4.1.495.2.1.6.36.2.1.34 | bopSapAdmPortRiRlSignalSamples | 0 | 0 | Determines the active number of sampling periods that this port must wait before validating RI (RL if DCE). This object has no me… |
1.3.6.1.4.1.495.2.1.6.36.2.1.35 | bopSapAdmPortStatisticsTimer | 0 | 0 | Determines the period in seconds during which BOP performance statistics are measured. Note: If set to zero, BOP performance stat… |
1.3.6.1.4.1.495.2.1.6.36.2.1.36 | bopSapAdmPortCarrierAction | 0 | 0 | Determines if the port driver informs it's associated upper layer that service is no longer available following loss of DCD if D… |
1.3.6.1.4.1.495.2.1.6.36.2.1.37 | bopSapAdmPortDataGenerator | 0 | 0 | Determines whether the port will act as an internal data generator. Options: disabled (1): port is not a data generator enabled (… |
1.3.6.1.4.1.495.2.1.6.36.2.1.38 | bopSapAdmPortGenFrames | 0 | 0 | Determines the number of frames that the port configured as an internal data generator will generate at one time. Ranges of Value… |
1.3.6.1.4.1.495.2.1.6.36.2.1.39 | bopSapAdmPortGenFrameSize | 0 | 0 | Determines the size in bytes of internally generated frames (excluding flags). Ranges of Values: 2-65535 Note: When set to zero, … |
1.3.6.1.4.1.495.2.1.6.36.2.1.40 | bopSapAdmPortGenFrameHeader | 0 | 0 | Determines the 16-bit header that will be inserted in the first two octets after the opening flag of each internally generated f… |
1.3.6.1.4.1.495.2.1.6.36.2.1.45 | bopSapAdmCodeSet | 0 | 0 | Determines in the administrative configuration the code used by the port associated with this SAP to communicate to the Bisync dev… |
1.3.6.1.4.1.495.2.1.6.36.2.1.46 | bopSapAdmParity | 0 | 0 | Indicates the parity used to communicate with the Bisync device Options: (1) none: No parity (2) odd: Odd parity (3) even: Even… |
1.3.6.1.4.1.495.2.1.6.36.2.1.47 | bopAdmPortTrap | 0 | 0 | Determines whether this port produces a 'bopPortStatusChange' trap which can be retrieved by SNMP network management. Options: dis… |
1.3.6.1.4.1.495.2.1.6.36.2.1.48 | bopAdmTxClockTrap | 0 | 0 | Determines whether this port produces a 'bopTxClockStatusChange' trap which can be retrieved by SNMP network management. Options:… |