This attribute is not applicable and is ignored for CQC-based ATM
cards.
This attribute specifies the emission priority (EP) which is used to
transmit traffic of the CBR service category. A lower numerical
value for this attribute specifies a higher emission priority. 0 is the
highest EP and 7 is the lowest. Cells at a higher emission priority
receive higher preference for link bandwidth. EPs 0 and 1 are in the
absolute priority range, and are unaffected by any minimum
bandwidth guarantees. EPs 2 through 7 are in the guaranteed
bandwidth range. Minimum bandwidth guarantee is specified in the
AtmIf/n Ep/m component.
Emission priority setting must comply with all of the following
constraints:
1. The emission priority numbers must be in the following order:
CBR <= rt-VBR <= nrt-VBR <= ABR <= UBR
2. Two different ATM service categories may share the same EP
only if they are both shaped.
3. CBR and rt-VBR may be placed either in the absolute priority
range (EP 0 or 1) or in the guaranteed bandwidth range (EP 2
through 7).
4. If both CBR and rt-VBR are shaped, rt-VBR must share the
same EP with CBR or ABR. If either one of CBR or rt-VBR are
not shaped, then they cannot share the same EP.
5. ABR service category is always deemed to be shaped. If nrt-VBR
is shaped, it must share the same EP with ABR. If nrt-VBR is not
shaped it must have a higher EP than ABR.
6. If UBR is shaped, it must share the same EP with ABR. If UBR
is not shaped, it must have a lower EP than ABR.
This attribute does not apply to standard Vpt Vccs and basic Vpts.
Parsed from file nortelPP-atmCoreV1_BG00S4C.mib.txt
Company: None
Module: Nortel-Magellan-Passport-AtmCoreMIB
This attribute is not applicable and is ignored for CQC-based ATM
cards.
This attribute specifies the emission priority (EP) which is used to
transmit traffic of the CBR service category. A lower numerical
value for this attribute specifies a higher emission priority. 0 is the
highest EP and 7 is the lowest. Cells at a higher emission priority
receive higher preference for link bandwidth. EPs 0 and 1 are in the
absolute priority range, and are unaffected by any minimum
bandwidth guarantees. EPs 2 through 7 are in the guaranteed
bandwidth range. Minimum bandwidth guarantee is specified in the
AtmIf/n Ep/m component.
Emission priority setting must comply with all of the following
constraints:
1. The emission priority numbers must be in the following order:
CBR <= rt-VBR <= nrt-VBR <= ABR <= UBR
2. Two different ATM service categories may share the same EP
only if they are both shaped.
3. CBR and rt-VBR may be placed either in the absolute priority
range (EP 0 or 1) or in the guaranteed bandwidth range (EP 2
through 7).
4. If both CBR and rt-VBR are shaped, rt-VBR must share the
same EP with CBR or ABR. If either one of CBR or rt-VBR are
not shaped, then they cannot share the same EP.
5. ABR service category is always deemed to be shaped. If nrt-VBR
is shaped, it must share the same EP with ABR. If nrt-VBR is not
shaped it must have a higher EP than ABR.
6. If UBR is shaped, it must share the same EP with ABR. If UBR
is not shaped, it must have a lower EP than ABR.
This attribute does not apply to standard Vpt Vccs and basic Vpts.
Parsed from file Nortel-Magellan-Passport-AtmCoreMIB.mib
Module: Nortel-Magellan-Passport-AtmCoreMIB
Vendor: Northern Telecom, Ltd.
Module: Nortel-Magellan-Passport-AtmCoreMIB
[Automatically extracted from oidview.com]
atmIfCACbrEmissionPriority OBJECT-TYPE SYNTAX Unsigned32 (0..7) ACCESS read-write STATUS mandatory DESCRIPTION "This attribute is not applicable and is ignored for CQC-based ATM cards. This attribute specifies the emission priority (EP) which is used to transmit traffic of the CBR service category. A lower numerical value for this attribute specifies a higher emission priority. 0 is the highest EP and 7 is the lowest. Cells at a higher emission priority receive higher preference for link bandwidth. EPs 0 and 1 are in the absolute priority range, and are unaffected by any minimum bandwidth guarantees. EPs 2 through 7 are in the guaranteed bandwidth range. Minimum bandwidth guarantee is specified in the AtmIf/n Ep/m component. Emission priority setting must comply with all of the following constraints: 1. The emission priority numbers must be in the following order: CBR <= rt-VBR <= nrt-VBR <= ABR <= UBR 2. Two different ATM service categories may share the same EP only if they are both shaped. 3. CBR and rt-VBR may be placed either in the absolute priority range (EP 0 or 1) or in the guaranteed bandwidth range (EP 2 through 7). 4. If both CBR and rt-VBR are shaped, rt-VBR must share the same EP with CBR or ABR. If either one of CBR or rt-VBR are not shaped, then they cannot share the same EP. 5. ABR service category is always deemed to be shaped. If nrt-VBR is shaped, it must share the same EP with ABR. If nrt-VBR is not shaped it must have a higher EP than ABR. 6. If UBR is shaped, it must share the same EP with ABR. If UBR is not shaped, it must have a lower EP than ABR. This attribute does not apply to standard Vpt Vccs and basic Vpts." DEFVAL { 0 } ::= { atmIfCACbrProvEntry 100 }
atmIfCACbrEmissionPriority OBJECT-TYPE SYNTAX Unsigned32 (0..7) ACCESS read-write STATUS mandatory DESCRIPTION "This attribute is not applicable and is ignored for CQC-based ATM cards. This attribute specifies the emission priority (EP) which is used to transmit traffic of the CBR service category. A lower numerical value for this attribute specifies a higher emission priority. 0 is the highest EP and 7 is the lowest. Cells at a higher emission priority receive higher preference for link bandwidth. EPs 0 and 1 are in the absolute priority range, and are unaffected by any minimum bandwidth guarantees. EPs 2 through 7 are in the guaranteed bandwidth range. Minimum bandwidth guarantee is specified in the AtmIf/n Ep/m component. Emission priority setting must comply with all of the following constraints: 1. The emission priority numbers must be in the following order: CBR <= rt-VBR <= nrt-VBR <= ABR <= UBR 2. Two different ATM service categories may share the same EP only if they are both shaped. 3. CBR and rt-VBR may be placed either in the absolute priority range (EP 0 or 1) or in the guaranteed bandwidth range (EP 2 through 7). 4. If both CBR and rt-VBR are shaped, rt-VBR must share the same EP with CBR or ABR. If either one of CBR or rt-VBR are not shaped, then they cannot share the same EP. 5. ABR service category is always deemed to be shaped. If nrt-VBR is shaped, it must share the same EP with ABR. If nrt-VBR is not shaped it must have a higher EP than ABR. 6. If UBR is shaped, it must share the same EP with ABR. If UBR is not shaped, it must have a lower EP than ABR. This attribute does not apply to standard Vpt Vccs and basic Vpts." DEFVAL { 0 } ::= { atmIfCACbrProvEntry 100 }
| OID | Name | Sub children | Sub Nodes Total | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.562.2.4.1.114.3.2.100.1.10 | atmIfCACbrProvPool | 0 | 0 | This attribute specifies the bandwidth pool which is to be used to support the constant bit rate (CBR) service category except f… |
| 1.3.6.1.4.1.562.2.4.1.114.3.2.100.1.20 | atmIfCACbrProvCdvt | 0 | 0 | This attribute specifies the default cell delay variation tolerance (CDVT) for all connections of the CBR service category excep… |
| 1.3.6.1.4.1.562.2.4.1.114.3.2.100.1.30 | atmIfCACbrCdv | 0 | 0 | This attribute specifies the peak-to-peak cell delay variation (CDV) which is contributed to the entire ATM Interface for CBR tr… |
| 1.3.6.1.4.1.562.2.4.1.114.3.2.100.1.40 | atmIfCACbrMaxCtd | 0 | 0 | This attribute specifies the maximum cell transfer delay (MaxCTD) which is applied to the entire ATM Interface for CBR traffic. … |
| 1.3.6.1.4.1.562.2.4.1.114.3.2.100.1.50 | atmIfCACbrProvClr | 0 | 0 | This attribute specifies the tolerable cell loss ratio (CLR) for CBR traffic except for connections managed by a Vpt CA. The num… |
| 1.3.6.1.4.1.562.2.4.1.114.3.2.100.1.60 | atmIfCACbrTxQueueLimit | 0 | 0 | This attribute specifies the default maximum queue length for the emission queues used to buffer the traffic of the CBR service c… |
| 1.3.6.1.4.1.562.2.4.1.114.3.2.100.1.61 | atmIfCACbrHoldingPriority | 0 | 0 | This attribute specifies the holding priority which applies to SVP and SVC CBR connections. It takes a value from 0 (highest prio… |
| 1.3.6.1.4.1.562.2.4.1.114.3.2.100.1.70 | atmIfCACbrSvcHoldingPriority | 0 | 0 | This attribute specifies the default holding priority which applies to SVC CBR connections. It takes a value from 0 (highest pri… |
| 1.3.6.1.4.1.562.2.4.1.114.3.2.100.1.71 | atmIfCACbrSvcMpHoldingPriority | 0 | 0 | This attribute specifies the default holding priority which applies to SVC CBR point-to-multipoint connections. It takes a value… |
| 1.3.6.1.4.1.562.2.4.1.114.3.2.100.1.80 | atmIfCACbrMinPerVcQueueLimit | 0 | 0 | This attribute specifies the minimum queue limit for the per-VC queues of connections of the CBR service category. This attribut… |
| 1.3.6.1.4.1.562.2.4.1.114.3.2.100.1.90 | atmIfCACbrPerVcQueueLimitReferenceRate | 0 | 0 | This attribute specifies the shaping rate to be used in computing the tolerable delay for per-VC queues of connections of the CB… |
| 1.3.6.1.4.1.562.2.4.1.114.3.2.100.1.140 | atmIfCACbrTrafficShaping | 0 | 0 | This attribute specifies the default traffic shaping option for connections of the CBR service category. An override to this def… |
| 1.3.6.1.4.1.562.2.4.1.114.3.2.100.1.150 | atmIfCACbrShapeRecoupPolicy | 0 | 0 | This attribute specifies the shaping recoup policy for the CBR service category. This is the policy which is used to recoup shap… |
| 1.3.6.1.4.1.562.2.4.1.114.3.2.100.1.160 | atmIfCACbrUnshapedTransmitQueueing | 0 | 0 | This attribute specifies the default queuing option for unshaped connections of the CBR service category. On ATM IP cards, this a… |
| 1.3.6.1.4.1.562.2.4.1.114.3.2.100.1.165 | atmIfCACbrWeightPolicy | 0 | 0 | This attribute specifies the default policy which is applied when calculating the fairness weight for unshaped connections of th… |
| 1.3.6.1.4.1.562.2.4.1.114.3.2.100.1.169 | atmIfCACbrForceTagging | 0 | 0 | This attribute specifies the default of whether to force tagging (CLP=1) of all cells for all CBR connections. An override to th… |
| 1.3.6.1.4.1.562.2.4.1.114.3.2.100.1.170 | atmIfCACbrUsageParameterControl | 0 | 0 | This attribute specifies the default usage parameter control (UPC) option for connections of the CBR service category. This attr… |