This attribute specifies the default traffic shaping option for
connections of the CBR service category. An override to this default
may be specified for a provisioned connection under the Vcd Tm or
Vpd Tm component.
When this attribute is set to disabled, traffic shaping cannot be
enabled for any CBR connections.
For CQC-based ATM FPs, this attribute must be set to disabled.
Traffic shaping is not supported for CBR connections on CQC-
based ATM FPs.
If the Vcc Tm, Vpc Tm, or Vpt Tm txTrafficDescType indicates type
1 or 2, this attribute is ignored, and traffic shaping is not applicable
for that connection.
When this attribute is set to inverseUpc, traffic shaping for a
connection is enabled according to the value of the Vcc Tm, Vpc
Tm, or Vpt Tm txTrafficDescType.
If this attribute is set to inverseUpc, and the txTrafficDescType is 3,
4, or 5, linear traffic shaping is enabled. Linear traffic shaping uses
a single static traffic shaping rate.
If this attribute is set to inverseUpc, and the txTrafficDescType is 6,
7, or 8, inverse-UPC (also referred to as VBR or dual leaky bucket)
traffic shaping is enabled. Inverse-UPC traffic shaping can burst
above the sustained cell rate to the peak cell rate for the duration
defined by maximum burst size. Inverse-UPC traffic shaping exactly
conforms to the requirements of a dual leaky bucket UPC enforcer.
When this attribute is set to enabled and the txTrafficDescType is 3,
4, 5, 6, 7, or 8, traffic shaping for a connection is enabled using
linear shaping.
Enabling or disabling traffic shaping may require a matching
change to the emissionPriority attribute and
unshapedTransmitQueueing attribute for this service category.
Refer to those attributes for the complete description of the
interactions.
This attribute does not apply to standard Vpt Vccs and basic Vpts.
Parsed from file nortelPP-atmCoreV1_BG00S4C.mib.txt
Company: None
Module: Nortel-Magellan-Passport-AtmCoreMIB
This attribute specifies the default traffic shaping option for
connections of the CBR service category. An override to this default
may be specified for a provisioned connection under the Vcd Tm or
Vpd Tm component.
When this attribute is set to disabled, traffic shaping cannot be
enabled for any CBR connections.
For CQC-based ATM FPs, this attribute must be set to disabled.
Traffic shaping is not supported for CBR connections on CQC-
based ATM FPs.
If the Vcc Tm, Vpc Tm, or Vpt Tm txTrafficDescType indicates type
1 or 2, this attribute is ignored, and traffic shaping is not applicable
for that connection.
When this attribute is set to inverseUpc, traffic shaping for a
connection is enabled according to the value of the Vcc Tm, Vpc
Tm, or Vpt Tm txTrafficDescType.
If this attribute is set to inverseUpc, and the txTrafficDescType is 3,
4, or 5, linear traffic shaping is enabled. Linear traffic shaping uses
a single static traffic shaping rate.
If this attribute is set to inverseUpc, and the txTrafficDescType is 6,
7, or 8, inverse-UPC (also referred to as VBR or dual leaky bucket)
traffic shaping is enabled. Inverse-UPC traffic shaping can burst
above the sustained cell rate to the peak cell rate for the duration
defined by maximum burst size. Inverse-UPC traffic shaping exactly
conforms to the requirements of a dual leaky bucket UPC enforcer.
When this attribute is set to enabled and the txTrafficDescType is 3,
4, 5, 6, 7, or 8, traffic shaping for a connection is enabled using
linear shaping.
Enabling or disabling traffic shaping may require a matching
change to the emissionPriority attribute and
unshapedTransmitQueueing attribute for this service category.
Refer to those attributes for the complete description of the
interactions.
This attribute does not apply to standard Vpt Vccs and basic Vpts.
Parsed from file Nortel-Magellan-Passport-AtmCoreMIB.mib
Module: Nortel-Magellan-Passport-AtmCoreMIB
Vendor: Northern Telecom, Ltd.
Module: Nortel-Magellan-Passport-AtmCoreMIB
[Automatically extracted from oidview.com]
atmIfCACbrTrafficShaping OBJECT-TYPE SYNTAX INTEGER { disabled(1), enabled(5), inverseUpc(6) } ACCESS read-write STATUS mandatory DESCRIPTION "This attribute specifies the default traffic shaping option for connections of the CBR service category. An override to this default may be specified for a provisioned connection under the Vcd Tm or Vpd Tm component. When this attribute is set to disabled, traffic shaping cannot be enabled for any CBR connections. For CQC-based ATM FPs, this attribute must be set to disabled. Traffic shaping is not supported for CBR connections on CQC- based ATM FPs. If the Vcc Tm, Vpc Tm, or Vpt Tm txTrafficDescType indicates type 1 or 2, this attribute is ignored, and traffic shaping is not applicable for that connection. When this attribute is set to inverseUpc, traffic shaping for a connection is enabled according to the value of the Vcc Tm, Vpc Tm, or Vpt Tm txTrafficDescType. If this attribute is set to inverseUpc, and the txTrafficDescType is 3, 4, or 5, linear traffic shaping is enabled. Linear traffic shaping uses a single static traffic shaping rate. If this attribute is set to inverseUpc, and the txTrafficDescType is 6, 7, or 8, inverse-UPC (also referred to as VBR or dual leaky bucket) traffic shaping is enabled. Inverse-UPC traffic shaping can burst above the sustained cell rate to the peak cell rate for the duration defined by maximum burst size. Inverse-UPC traffic shaping exactly conforms to the requirements of a dual leaky bucket UPC enforcer. When this attribute is set to enabled and the txTrafficDescType is 3, 4, 5, 6, 7, or 8, traffic shaping for a connection is enabled using linear shaping. Enabling or disabling traffic shaping may require a matching change to the emissionPriority attribute and unshapedTransmitQueueing attribute for this service category. Refer to those attributes for the complete description of the interactions. This attribute does not apply to standard Vpt Vccs and basic Vpts." DEFVAL { disabled } ::= { atmIfCACbrProvEntry 140 }
atmIfCACbrTrafficShaping OBJECT-TYPE SYNTAX INTEGER { disabled(1), enabled(5), inverseUpc(6) } ACCESS read-write STATUS mandatory DESCRIPTION "This attribute specifies the default traffic shaping option for connections of the CBR service category. An override to this default may be specified for a provisioned connection under the Vcd Tm or Vpd Tm component. When this attribute is set to disabled, traffic shaping cannot be enabled for any CBR connections. For CQC-based ATM FPs, this attribute must be set to disabled. Traffic shaping is not supported for CBR connections on CQC- based ATM FPs. If the Vcc Tm, Vpc Tm, or Vpt Tm txTrafficDescType indicates type 1 or 2, this attribute is ignored, and traffic shaping is not applicable for that connection. When this attribute is set to inverseUpc, traffic shaping for a connection is enabled according to the value of the Vcc Tm, Vpc Tm, or Vpt Tm txTrafficDescType. If this attribute is set to inverseUpc, and the txTrafficDescType is 3, 4, or 5, linear traffic shaping is enabled. Linear traffic shaping uses a single static traffic shaping rate. If this attribute is set to inverseUpc, and the txTrafficDescType is 6, 7, or 8, inverse-UPC (also referred to as VBR or dual leaky bucket) traffic shaping is enabled. Inverse-UPC traffic shaping can burst above the sustained cell rate to the peak cell rate for the duration defined by maximum burst size. Inverse-UPC traffic shaping exactly conforms to the requirements of a dual leaky bucket UPC enforcer. When this attribute is set to enabled and the txTrafficDescType is 3, 4, 5, 6, 7, or 8, traffic shaping for a connection is enabled using linear shaping. Enabling or disabling traffic shaping may require a matching change to the emissionPriority attribute and unshapedTransmitQueueing attribute for this service category. Refer to those attributes for the complete description of the interactions. This attribute does not apply to standard Vpt Vccs and basic Vpts." DEFVAL { disabled } ::= { atmIfCACbrProvEntry 140 }
| OID | Name | Sub children | Sub Nodes Total | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.562.2.4.1.114.3.2.100.1.10 | atmIfCACbrProvPool | 0 | 0 | This attribute specifies the bandwidth pool which is to be used to support the constant bit rate (CBR) service category except f… |
| 1.3.6.1.4.1.562.2.4.1.114.3.2.100.1.20 | atmIfCACbrProvCdvt | 0 | 0 | This attribute specifies the default cell delay variation tolerance (CDVT) for all connections of the CBR service category excep… |
| 1.3.6.1.4.1.562.2.4.1.114.3.2.100.1.30 | atmIfCACbrCdv | 0 | 0 | This attribute specifies the peak-to-peak cell delay variation (CDV) which is contributed to the entire ATM Interface for CBR tr… |
| 1.3.6.1.4.1.562.2.4.1.114.3.2.100.1.40 | atmIfCACbrMaxCtd | 0 | 0 | This attribute specifies the maximum cell transfer delay (MaxCTD) which is applied to the entire ATM Interface for CBR traffic. … |
| 1.3.6.1.4.1.562.2.4.1.114.3.2.100.1.50 | atmIfCACbrProvClr | 0 | 0 | This attribute specifies the tolerable cell loss ratio (CLR) for CBR traffic except for connections managed by a Vpt CA. The num… |
| 1.3.6.1.4.1.562.2.4.1.114.3.2.100.1.60 | atmIfCACbrTxQueueLimit | 0 | 0 | This attribute specifies the default maximum queue length for the emission queues used to buffer the traffic of the CBR service c… |
| 1.3.6.1.4.1.562.2.4.1.114.3.2.100.1.61 | atmIfCACbrHoldingPriority | 0 | 0 | This attribute specifies the holding priority which applies to SVP and SVC CBR connections. It takes a value from 0 (highest prio… |
| 1.3.6.1.4.1.562.2.4.1.114.3.2.100.1.70 | atmIfCACbrSvcHoldingPriority | 0 | 0 | This attribute specifies the default holding priority which applies to SVC CBR connections. It takes a value from 0 (highest pri… |
| 1.3.6.1.4.1.562.2.4.1.114.3.2.100.1.71 | atmIfCACbrSvcMpHoldingPriority | 0 | 0 | This attribute specifies the default holding priority which applies to SVC CBR point-to-multipoint connections. It takes a value… |
| 1.3.6.1.4.1.562.2.4.1.114.3.2.100.1.80 | atmIfCACbrMinPerVcQueueLimit | 0 | 0 | This attribute specifies the minimum queue limit for the per-VC queues of connections of the CBR service category. This attribut… |
| 1.3.6.1.4.1.562.2.4.1.114.3.2.100.1.90 | atmIfCACbrPerVcQueueLimitReferenceRate | 0 | 0 | This attribute specifies the shaping rate to be used in computing the tolerable delay for per-VC queues of connections of the CB… |
| 1.3.6.1.4.1.562.2.4.1.114.3.2.100.1.100 | atmIfCACbrEmissionPriority | 0 | 0 | This attribute is not applicable and is ignored for CQC-based ATM cards. This attribute specifies the emission priority (EP) whi… |
| 1.3.6.1.4.1.562.2.4.1.114.3.2.100.1.150 | atmIfCACbrShapeRecoupPolicy | 0 | 0 | This attribute specifies the shaping recoup policy for the CBR service category. This is the policy which is used to recoup shap… |
| 1.3.6.1.4.1.562.2.4.1.114.3.2.100.1.160 | atmIfCACbrUnshapedTransmitQueueing | 0 | 0 | This attribute specifies the default queuing option for unshaped connections of the CBR service category. On ATM IP cards, this a… |
| 1.3.6.1.4.1.562.2.4.1.114.3.2.100.1.165 | atmIfCACbrWeightPolicy | 0 | 0 | This attribute specifies the default policy which is applied when calculating the fairness weight for unshaped connections of th… |
| 1.3.6.1.4.1.562.2.4.1.114.3.2.100.1.169 | atmIfCACbrForceTagging | 0 | 0 | This attribute specifies the default of whether to force tagging (CLP=1) of all cells for all CBR connections. An override to th… |
| 1.3.6.1.4.1.562.2.4.1.114.3.2.100.1.170 | atmIfCACbrUsageParameterControl | 0 | 0 | This attribute specifies the default usage parameter control (UPC) option for connections of the CBR service category. This attr… |