BSUWIRELESSIF-MIB DEFINITIONS ::= BEGIN IMPORTS OBJECT-TYPE, MODULE-IDENTITY, Integer32 FROM SNMPv2-SMI MacAddress, TruthValue, DisplayString FROM SNMPv2-TC bsu FROM ANIROOT-MIB; -- the BSU Wireless Interface group aniBsuWirelessIf MODULE-IDENTITY LAST-UPDATED "0302101530Z" -- Wed Feb 10 15:30:00 PDT 2003 ORGANIZATION "Aperto Networks" CONTACT-INFO " Postal: Aperto Networks Inc 1637 S Main Street Milpitas, California 95035 Tel: +1 408 719 9977 " DESCRIPTION "This group contains BSU Wireless Interface information. It shows parameters for each configured Wireless Port on the BSU. It displays the following tables: aniBsuWirelessPortTable - with basic wireless port information aniBsuChannelTable - with Channel related information aniBsuQosLinkTable - with QOS Link related information aniBsuPowerControlTable - with Power control related information aniBsuAntennaTable - with Antenna related information aniBsuSectorTable - with Sector related information aniBsuWirelessPtPConfGroup - PacketWave 620 Wireless Configuration group aniBsuWirelessPtpStatusGroup - PacketWave 620 Wireless Status information aniBsuWirelessFreqAdminTable - PacketWave 620/750/1000 FrequencyTable Configuration aniBsuWirelessFreqOperTable - PacketWave 620/750/1000 Current FrequencyTable display aniBsuWirelessSysConfGroup - PacketWave 1000/760 per system Configuration group aniBsuWirelessIfConfTable - PacketWave 1000/760 per port Wireless Configuration table aniBsuWirelessAFSTable - PacketWave 1000/760 per port AFS Configuration table " ::= { bsu 2 } aniBsuWirelessPortTable OBJECT-TYPE SYNTAX SEQUENCE OF AniBsuWirelessPortEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains entries with basic information about each BSU Wireless Port. " ::= { aniBsuWirelessIf 1 } aniBsuWirelessPortEntry OBJECT-TYPE SYNTAX AniBsuWirelessPortEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry containing basic information for this particular wireless port. " INDEX { aniBsuWirelessPort } ::= { aniBsuWirelessPortTable 1 } AniBsuWirelessPortEntry ::= SEQUENCE { aniBsuWirelessPort INTEGER, aniBsuPortMacAddr MacAddress, aniBsuPortState INTEGER, aniBsuPortReset TruthValue, aniBsuPortFlag INTEGER } aniBsuWirelessPort OBJECT-TYPE SYNTAX INTEGER { wireless-port1(1), wireless-port2(2), wireless-port3(3), wireless-port4(4), wireless-port5(5), wireless-port6(6) } MAX-ACCESS read-only STATUS current DESCRIPTION "The wireless port number. " ::= { aniBsuWirelessPortEntry 1 } aniBsuPortMacAddr OBJECT-TYPE SYNTAX MacAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The MAC Address of the wireless port. This field is not applicable when BSU is running as a bridge. The agent will display a blank string for this case. " ::= { aniBsuWirelessPortEntry 2 } aniBsuPortState OBJECT-TYPE SYNTAX INTEGER { unavailable(1), initial(2), unconfig(3), starting(4), configured-no-radio-detected(5), operational-radio(6), stopped(7), resetting(8), disabled(9) } MAX-ACCESS read-only STATUS current DESCRIPTION "The current state of the wireless port." ::= { aniBsuWirelessPortEntry 3 } aniBsuPortReset OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "This object is used to reset an individual wireless port. Setting this parameter to true(1) causes the port to reset. " ::= { aniBsuWirelessPortEntry 4 } aniBsuPortFlag OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "This flag is used to turn a particular wireless port on or off, that is, to selectively enable(1) or disable(2) a port. It is valid only for configured ports. By default, all configured ports are enabled unless explicitly disabled during configuration. The disabled ports may later be enabled dynamically(without reboot). " DEFVAL { 1 } ::= { aniBsuWirelessPortEntry 5 } aniBsuChannelTable OBJECT-TYPE SYNTAX SEQUENCE OF AniBsuChannelEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains Channel related information for each BSU Wireless interface. " ::= { aniBsuWirelessIf 4 } aniBsuChannelEntry OBJECT-TYPE SYNTAX AniBsuChannelEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry containing Channel attributes for this particular interface. " INDEX { aniBsuWirelessPort } ::= { aniBsuChannelTable 1 } AniBsuChannelEntry ::= SEQUENCE { aniBsuChannelFrequency DisplayString, aniBsuChannelWidth DisplayString, aniBsuFrequencyBand INTEGER, aniBsuNumServFlowsPerSu Integer32, aniBsuNumSusSupported Integer32, aniBsuSuRadioRegPowerLimit INTEGER, aniBsuTargetFrequency DisplayString } aniBsuChannelFrequency OBJECT-TYPE SYNTAX DisplayString UNITS "MHz" MAX-ACCESS read-only STATUS current DESCRIPTION "The Current Channel Center Frequency in MHz. If no radio is detected, this object will display a value of 0. When Frequency Band is FDD, both transmit and receive frequencies will be displayed in the format 'transmit frequency - receive frequency'. " ::= { aniBsuChannelEntry 2 } aniBsuFrequencyBand OBJECT-TYPE SYNTAX INTEGER { unii-5-3GHz(1), unii-5-8GHz(2), general-5-8GHz(3), ism-5-8GHz(10), mmds-2-6GHz(4), general-2-6GHz(5), general-3-5GHz(6), etsi-3-5GHz-50(7), etsi-3-5GHz-100(8), fdd-3-5GHz(11), general-5-3GHz(12) } MAX-ACCESS read-only STATUS current DESCRIPTION "The Frequency Band to which the Channel Center Frequency belongs. Valid Range: 1 - 5.3 GHz UNII Band (5250 - 5350 MHz) 12 - 5.3 GHz General Band (5150 - 5350 MHz) 2 - 5.8 GHz UNII Band (5725 - 5825 MHz) 3 - 5.8 GHz General (5725 - 5925 MHz) 10 - 5.8 GHz ISM Band (5725 - 5850 MHz) 4 - 2.6 GHz MMDS Band (2500 - 2689 MHz) 5 - 2.6 GHz General (2500 - 2700 MHz) 6 - 3.5 GHz General (3300 - 3800 MHz) 7 - 3.5 GHz ETSI Band - 50 MHz duplexing Scheme (3410 - 3800 MHz) 8 - 3.5 GHz ETSI Band - 100 MHz duplexing Scheme (3410 - 3800 MHz) 11 - 3.5 GHz FDD Band " ::= { aniBsuChannelEntry 3 } aniBsuChannelWidth OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "The Width of frequency channel in MHz. " ::= { aniBsuChannelEntry 4 } aniBsuNumServFlowsPerSu OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of Service Flows supported per SU. " ::= { aniBsuChannelEntry 6 } aniBsuNumSusSupported OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of SUs supported by this wireless port. " ::= { aniBsuChannelEntry 7 } aniBsuSuRadioRegPowerLimit OBJECT-TYPE SYNTAX INTEGER UNITS "dBm" MAX-ACCESS read-only STATUS current DESCRIPTION "This parameter constraints the maximum power at which a SU radio can transmit. This information is conveyed to all the SUs within a WSS via the CD packet. It is equal to the EIRP (Effective Incidental Radiated Power) specified by the Regulatory Body. Note: If you are using an older version of the Configuration Manager, this object is not defined in dBm. Instead, the following values will be displayed: nominal(1), one-level-above-nominal(2), two-levels-above-nominal(3), three-levels-above-nominal(4), one-level-below-nominal(5), two-levels-below-nominal(6) " ::= { aniBsuChannelEntry 9 } aniBsuTargetFrequency OBJECT-TYPE SYNTAX DisplayString UNITS "MHz" MAX-ACCESS read-only STATUS current DESCRIPTION "The Current Target Frequency in MHz. To change the configuration of this value, use the object aniBsuWirelessIfConfTargetFrequency for PW1000 (or aniBsuWirelessPtPConfTargetFrequency for PW620). When Frequency Band is FDD, both transmit and receive frequencies will be displayed in the format 'transmit frequency - receive frequency'. Target frequency cannot be modified for FDD band. " ::= { aniBsuChannelEntry 10 } aniBsuQosLinkTable OBJECT-TYPE SYNTAX SEQUENCE OF AniBsuQosLinkEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains QOS Link related information for each BSU Wireless port. The total sum of BE, CIR, CBR bandwidths should be 100%. " ::= { aniBsuWirelessIf 6 } aniBsuQosLinkEntry OBJECT-TYPE SYNTAX AniBsuQosLinkEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry containing QOS Link attributes for this particular port. " INDEX { aniBsuWirelessPort } ::= { aniBsuQosLinkTable 1 } AniBsuQosLinkEntry ::= SEQUENCE { aniBsuBEBandwidth Integer32, aniBsuCIRBandwidth Integer32, aniBsuCBRBandwidth Integer32 } aniBsuBEBandwidth OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The BE Bandwidth as a percentage of total bandwidth. " ::= { aniBsuQosLinkEntry 1 } aniBsuCIRBandwidth OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The CIR Bandwidth as a percentage of total bandwidth. " ::= { aniBsuQosLinkEntry 2 } aniBsuCBRBandwidth OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The CBR Bandwidth as a percentage of total bandwidth. " ::= { aniBsuQosLinkEntry 3 } aniBsuPowerControlTable OBJECT-TYPE SYNTAX SEQUENCE OF AniBsuPowerControlEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains Power Control related information for each BSU Wireless port. " ::= { aniBsuWirelessIf 7 } aniBsuPowerControlEntry OBJECT-TYPE SYNTAX AniBsuPowerControlEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry containing Power Control attributes for this particular port. " INDEX { aniBsuWirelessPort } ::= { aniBsuPowerControlTable 1 } AniBsuPowerControlEntry ::= SEQUENCE { aniBsuReceivePower Integer32, aniBsuWssRadioRegPowerLimit INTEGER } aniBsuReceivePower OBJECT-TYPE SYNTAX Integer32 (-90..-60) UNITS "dBm" MAX-ACCESS read-write STATUS current DESCRIPTION "This parameter sets the upstream receiver power on the WSS. The range is between -60 to -90 (dBm) It cannot be modified when BSU is in point to point mode. " ::= { aniBsuPowerControlEntry 2 } aniBsuWssRadioRegPowerLimit OBJECT-TYPE SYNTAX INTEGER UNITS "dBm" MAX-ACCESS read-only STATUS current DESCRIPTION "This parameter constraints the maximum power at which the radio for this WSS can transmit. It is equal to the EIRP (Effective Incidental Radiated Power) specified by the Regulatory Body. Note: If you are using an older version of the Configuration Manager, this object is not defined in dBm. Instead, the following values will be displayed: nominal(1), one-level-above-nominal(2), two-levels-above-nominal(3), three-levels-above-nominal(4), one-level-below-nominal(5), two-levels-below-nominal(6) " ::= { aniBsuPowerControlEntry 3 } aniBsuAntennaTable OBJECT-TYPE SYNTAX SEQUENCE OF AniBsuAntennaEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains Antenna related information for each BSU Wireless port. " ::= { aniBsuWirelessIf 8 } aniBsuAntennaEntry OBJECT-TYPE SYNTAX AniBsuAntennaEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry containing Antenna attributes for this particular port. " INDEX { aniBsuWirelessPort } ::= { aniBsuAntennaTable 1 } AniBsuAntennaEntry ::= SEQUENCE { aniBsuAntennaDiversityFlag INTEGER, aniBsuAntennaDiversityMode INTEGER, aniBsuBcastAntennaPolarization INTEGER } aniBsuAntennaDiversityFlag OBJECT-TYPE SYNTAX INTEGER { enable (1), disable (2) } MAX-ACCESS read-only STATUS current DESCRIPTION "This flag shows whether antenna diversity has been enabled (1) or disabled (2) for this SU. " ::= { aniBsuAntennaEntry 1 } aniBsuAntennaDiversityMode OBJECT-TYPE SYNTAX INTEGER { sync-based (1), training-seq-based (2) } MAX-ACCESS read-only STATUS current DESCRIPTION "This shows whether diversity is Sync Based (1) or Training Sequence Based (2) " ::= { aniBsuAntennaEntry 2 } aniBsuBcastAntennaPolarization OBJECT-TYPE SYNTAX INTEGER { horizontal(1), vertical(2), horizontal-and-vertical(3) } MAX-ACCESS read-only STATUS current DESCRIPTION "The default broadcast antenna polarization. " ::= { aniBsuAntennaEntry 4 } aniBsuSectorTable OBJECT-TYPE SYNTAX SEQUENCE OF AniBsuSectorEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains Sector related information for each BSU Wireless port. " ::= { aniBsuWirelessIf 9 } aniBsuSectorEntry OBJECT-TYPE SYNTAX AniBsuSectorEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry containing Sector attributes for this particular port. " INDEX { aniBsuWirelessPort } ::= { aniBsuSectorTable 1 } AniBsuSectorEntry ::= SEQUENCE { aniBsuSectorName DisplayString } aniBsuSectorName OBJECT-TYPE SYNTAX DisplayString (SIZE (0..80)) MAX-ACCESS read-only STATUS current DESCRIPTION "The descriptive name of the sector identified by aniBsuSectorId. " ::= { aniBsuSectorEntry 2 } -- Configuration for PW620 (Point to Point): -- The aniBsuWirelessPtPConfGroup contains configurable wireless -- paramters for each AP. aniBsuWirelessPtPConfGroup OBJECT IDENTIFIER ::= { aniBsuWirelessIf 10 } aniBsuWirelessPtPConfFrequencyBand OBJECT-TYPE SYNTAX INTEGER { unii-5-3GHz(1), unii-5-8GHz(2), general-5-8GHz(3), ism-5-8GHz(10), mmds-2-6GHz(4), general-2-6GHz(5), general-3-5GHz(6), etsi-3-5GHz-50(7), etsi-3-5GHz-100(8) } MAX-ACCESS read-only STATUS current DESCRIPTION "The Frequency Band to which the Channel Center Frequency belongs. Valid Range: 1 - 5.3 GHz UNII Band (5250 - 5350 MHz) 12 - 5.3 GHz General Band (5150 - 5350 MHz) 2 - 5.8 GHz UNII Band (5725 - 5825 MHz) 3 - 5.8 GHz General (5650 - 5925 MHz) 10 - 5.8 GHz ISM Band (5725 - 5850 MHz) 4 - 2.6 GHz MMDS Band (2500 - 2689 MHz) 5 - 2.6 GHz General (2500 - 2700 MHz) 6 - 3.5 GHz General (3300 - 3800 MHz) 7 - 3.5 GHz ETSI Band - 50 MHz duplexing Scheme (3410 - 3800 MHz) 8 - 3.5 GHz ETSI Band - 100 MHz duplexing Scheme (3410 - 3800 MHz) " ::= { aniBsuWirelessPtPConfGroup 1 } aniBsuWirelessPtPConfChannelWidth OBJECT-TYPE SYNTAX INTEGER { width-2(2000), width-3(3000), width-4(4000), width-5(5000), width-6(6000), width-7(7000), width-3-5(3500) } MAX-ACCESS read-write STATUS current DESCRIPTION "The Channel Width. width-2 refers to 2MHz, width-3 refers to 3MHz width-4 refers to 4MHz, width-5 refers to 5MHz,width-6 refers to 6MHz width-7 refers to 7MHz, width-1-75 refers to 1.75MHz, width-3-5 refers to 3.5MHz Channel Width depends on Frequency Band. The valid range is as follows: 3.5 GHz (ETSI) should allow channel width 3.5, 7; the rest of bands should allow channel width 2,3, 4, 5 and 6 The Channel Width, Frame size, Downstream/Upstream ratio and cell radius are dependent on each other and the following restrictions should be taken into account when configuring the system: Low Latency Mode Channel Width = 1.75, 2, 3, 3.5 or 4 Not supported Channel Width = 5, distance must be <= 30km Percentage downstream bandwidth must be >= 50 Channel Width = 6 or 7, distance must be <= 40km Percentage downstream bandwidth must be >= 50 Normal Mode Channel Width = 1.75 Not supported Channel Width = 2, if DS/US is 50/50 then distance must be <100km Channel Width = 2, if DS/US is 60/40 then distance must be <90km Channel Width = 2, if DS/US is 70/30 then distance must be <50km Channel Width = 3, if DS/US is 50/50 then distance must be <100km Channel Width = 3, if DS/US is 60/40 then distance must be <100km Channel Width = 3, if DS/US is 70/30 then distance must be <90km Channel Width = 3.5, 4,5, 6 and 7, DS/US must be >= 50 Note: It is required to upload the configuration and then reboot the device for the changes to take effect. " ::= { aniBsuWirelessPtPConfGroup 2 } aniBsuWirelessPtPConfTDDFrameSize OBJECT-TYPE SYNTAX INTEGER { low-latency(1), normal-mode(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "The total size of the TDD Frame. For PW620, only low-latency and normal-mode are allowed. Also refer to the constraints listed under aniBsuWirelessPtPConfChannelWidth description. Note: When this object is changed through SNMP agent, it is required to upload the configuration (set aniDevControlStartUpload in the device_control.mib to true) and then reboot the device for the changes to take effect. " ::= { aniBsuWirelessPtPConfGroup 3 } aniBsuWirelessPtPConfCellRadius OBJECT-TYPE SYNTAX INTEGER { radius10km(10000), radius20km(20000), radius30km(30000), radius40km(40000), radius50km(50000), radius60km(60000), radius70km(70000), radius80km(80000), radius90km(90000), radius100km(100000) } MAX-ACCESS read-write STATUS current DESCRIPTION "The cell radius or link distance Refer to the constraints listed under aniBsuWirelessPtPConfChannelWidth description. Note: When this object is changed through SNMP agent, it is required to upload the configuration (set aniDevControlStartUpload in the device_control.mib to true) and then reboot the device for the changes to take effect. " ::= { aniBsuWirelessPtPConfGroup 4 } aniBsuWirelessPtPConfDSUSRatio OBJECT-TYPE SYNTAX INTEGER { ds70-us30(70), ds60-us40(60), ds50-us50(50), ds40-us60(40), ds30-us70(30) } MAX-ACCESS read-write STATUS current DESCRIPTION "The Downstream upstream ratio (DS/US ratio). This allows the user to configure how the total available bandwidth is split between downstream and upsteam. ds70-us30 is 70/30 ds60-us40 is 60/40 ds50-us50 is 50/50 ds40-us60 is 40/60 ds30-us70 is 30/70 Also refer to the constraints listed under aniBsuWirelessPtPConfChannelWidth description. Note: When this object is changed through SNMP agent, it is required to upload the configuration (set aniDevControlStartUpload in the device_control.mib to true) and then reboot the device for the changes to take effect. " ::= { aniBsuWirelessPtPConfGroup 5 } aniBsuWirelessPtPConfPolarization OBJECT-TYPE SYNTAX INTEGER { vertical(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "The antenna polarization. " ::= { aniBsuWirelessPtPConfGroup 6 } aniBsuWirelessPtPConfTargetFrequency OBJECT-TYPE SYNTAX DisplayString UNITS "MHz" MAX-ACCESS read-write STATUS current DESCRIPTION "The Target Frequency in MHz. Its range depends on Channel Width. 1) 5.3 GHz UNII Band (5250 - 5350 MHz). The center frequencies in this band are within 5250 + Half of Channel Width MHz and 5350 - Half of Channel Width MHz and can have any integer value (in MHz) 2) 5.8 GHz UNII Band (5725 - 5825 MHz). The center frequencies in this band are within 5725 + Half of Channel Width MHz and 5825 - Half of Channel Width MHz and can have any integer value (in MHz). 3) 5.8 GHz General (5650 - 5925 MHz). The center frequencies in this band are within 5650 + Half of Channel Width MHz and 5925 - Half of Channel Width MHz and can have any integer value (in MHz). 4) 2.6 GHz MMDS Band (2500 - 2689 MHz). The center frequencies in this band are 2503 + 6N MHz where N = 0,1,2,.,30 5) 2.6 GHz General (2500 - 2700 MHz). The center frequencies in this band are within 2500 + Half of Channel Width MHz and 2700 - Half of Channel Width MHz and can have any integer value (in MHz). 6) 3.5 GHz General (3300 - 3800 MHz). The center frequencies in this band are within 3300 + Half of Channel Width MHz and 3800 - Half of Channel Width MHz and can have any integer value (in MHz). 7) 3.5 GHz ETSI Band - 50 MHz duplexing Scheme (3410 - 3800 MHz). 8) 3.5 GHz ETSI Band - 100 MHz duplexing scheme (3410 - 3800 MHz). 10) 5.8 GHz ISM Band (5725 - 5850 MHz). The center frequencies in this band are within 5725 + Half of Channel Width MHz and 5850 - Half of Channel Width MHz and can have any integer value (in MHz). 11) 5.3 GHz General Band (5150 - 5350 MHz). The center frequencies in this band are within 5150 + Half of Channel Width MHz and 5350 - Half of Channel Width MHz and can have any integer value (in MHz) Note: The term Half of Channel Width in all the descriptions above, is a rounded off value (with 0.5 rounded to 1). Note: When this object is changed through SNMP agent, the value could take effect immediately depending on the current channel center frequency value. If aniBsuWirelessPtPConfTargetFrequency is modified, but the current aniBsuChannelFrequency value is still one of the entries in aniBsuWirelessFreqOperTable, then the target frequency will not take effect immediately. However it could take effect later on when the current frequency entry is deleted from the frequency table. " ::= { aniBsuWirelessPtPConfGroup 7 } aniBsuWirelessPtPConfBsuRadioRegPowerLimit OBJECT-TYPE SYNTAX INTEGER UNITS "dBm" MAX-ACCESS read-write STATUS current DESCRIPTION "It is the maximum power at which the BSU radio is allowed to transmit. Antenna Gain is added to this maximum power to get EIRP (Effective Incidental Radiated Power) Valid Range - For 5.3GHz radios: 8 to 20 dBm For 5.8GHz radios: 8 to 20 dBm For 3.5GHz radios: 10 to 23 dBm For 2.6GHz radios: 10 to 23 dBm " ::= { aniBsuWirelessPtPConfGroup 8 } aniBsuWirelessPtPConfSuRadioRegPowerLimit OBJECT-TYPE SYNTAX INTEGER UNITS "dBm" MAX-ACCESS read-write STATUS current DESCRIPTION "It is the maximum power at which a SU radio is allowed to transmit. This information is conveyed to all the SUs via the CD packet. Antenna Gain is added to this maximum power to get EIRP (Effective Incidental Radiated Power) Valid Range - For 5.3GHz radios: 8 to 20 dBm For 5.8GHz radios: 8 to 20 dBm For 3.5GHz radios: 10 to 23 dBm For 2.6GHz radios: 10 to 23 dBm " ::= { aniBsuWirelessPtPConfGroup 9 } aniBsuWirelessPtPConfModify OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "This flag is used to modify and commit the changes of the dependent parameters from this group: aniBsuWirelessPtPConfChannelWidth aniBsuWirelessPtPConfTDDFrameSize aniBsuWirelessPtPConfCellRadius aniBsuWirelessPtPConfDSUSRatio aniBsuWirelessPtPConfPolarization aniBsuWirelessPtPConfTargetFrequency aniBsuWirelessPtPConfBsuRadioRegPowerLimit aniBsuWirelessPtPConfSuRadioRegPowerLimit aniBsuWirelessFreqAdminTable Setting this object to true(1) causes the agent to validate the entire set of parameters. If these set of values are acceptable, then the new values are changed on the device. However, for the changes to take effect, it is required to upload the configuration (set aniDevControlStartUpload in the device_control.mib to true) and then reboot the device. If the validation fails when aniBsuWirelessPtPConfModify is set to true(1), the changes are not commited and an error is returned. In that case, the modified parameters in this group may not reflect the correct values. They will display the values last configured by the user, rather than the current values on the device. To view the current values for aniBsuWirelessPtPConfChannelWidth refer to aniBsuChannelWidth aniBsuWirelessPtPConfTDDFrameSize refer to aniBsuTDDFrameSize aniBsuWirelessPtPConfCellRadius refer to aniBsuStatusCellRadius (bsu_status.mib) aniBsuWirelessPtPConfTargetFrequency refer to aniBsuTargetFrequency aniBsuWirelessPtPConfBsuRadioRegPowerLimit refer to aniBsuWssRadioRegPowerLimit aniBsuWirelessPtPConfSuRadioRegPowerLimit refer to aniBsuSuRadioRegPowerLimit aniBsuWirelessFreqAdminTable refer to aniBsuWirelessFreqOperTable A Get request on this object will always return false(2). " ::= { aniBsuWirelessPtPConfGroup 10 } aniBsuWirelessPtPConfBsuId OBJECT-TYPE SYNTAX DisplayString (SIZE (0..14)) MAX-ACCESS read-write STATUS current DESCRIPTION "The unique AP/BSU identifier. This is the AP ID required for generating seed for frequency reuse support. Note: When this object is changed through SNMP agent, it is required to upload the configuration (set aniDevControlStartUpload in the device_control.mib to true) and then reboot the device for the changes to take effect. " ::= { aniBsuWirelessPtPConfGroup 11 } aniBsuWirelessPtPConfVerifyAllSu OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "This flag is used to verify if the current set of BSU wireless parameters, that is, aniBsuWirelessPtPConfChannelWidth, aniBsuWirelessPtPConfTargetFrequency, aniBsuWirelessPtPConfBsuId are correctly configured on all the SUs connected. The values are compared against all the SUs connected to this BSU. Sending a Get request on this object causes the agent to verify the above set of parameters. If these set of values are incorrect, an error string is returned indicating that some values are not in sync. If the current set of values are correct, then the string 'No error' is displayed. This object might require upto 10 seconds to respond if multiple SUs are connected. Therefore, to ensure that it does not timeout before getting the complete results, the SNMP Manager tool should increase it's timeout value for this object to more than 10 seconds. " ::= { aniBsuWirelessPtPConfGroup 12 } aniBsuWirelessPtPConfSwitchToFrequency OBJECT-TYPE SYNTAX DisplayString UNITS "MHz" MAX-ACCESS read-write STATUS current DESCRIPTION "The Frequency selected to be switched. This frequency should be either one of the frequency entries in the aniBsuWirelessFreqOperTable or the current target frequency aniBsuTargetFrequency. A get request on this object will display the current frequency, aniBsuChannelFrequency and if no radio is detected, it will display 0.00. " ::= { aniBsuWirelessPtPConfGroup 13 } aniBsuWirelessPtPConfSuAFSTimeout OBJECT-TYPE SYNTAX INTEGER (1..300) MAX-ACCESS read-write STATUS current DESCRIPTION "Configure AFS SU Timeout (second) " ::= { aniBsuWirelessPtPConfGroup 14 } aniBsuWirelessPtPStatusGroup OBJECT IDENTIFIER ::= { aniBsuWirelessIf 11 } aniBsuWirelessPtPStatusMaxDSAvailBW OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "The maximum Downstream available bandwidth in kbps based on the current wireless configuration. " ::= { aniBsuWirelessPtPStatusGroup 1 } aniBsuWirelessPtPStatusMaxUSAvailBW OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "The maximum Upstream available bandwidth in kbps based on the current wireless configuration. " ::= { aniBsuWirelessPtPStatusGroup 2 } aniBsuWirelessPtPStatusTDDFrameSize OBJECT-TYPE SYNTAX INTEGER { low-latency(1), normal-mode(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "The total size of the TDD Frame low-latency is 2000 ticks normal-mode is 5000 ticks or 2500 ticks For PW620, only low-latency and normal-mode are allowed. Also refer to the constraints listed under aniBsuWirelessPtPConfChannelWidth description. " ::= { aniBsuWirelessPtPStatusGroup 3 } -- Frequency Related Configuration and Status aniBsuWirelessFreqAdminTable OBJECT-TYPE SYNTAX SEQUENCE OF AniBsuWirelessFreqAdminEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table is used to configure the BSU frequency table. " ::= { aniBsuWirelessIf 12 } aniBsuWirelessFreqAdminEntry OBJECT-TYPE SYNTAX AniBsuWirelessFreqAdminEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry containing the frequncy for this particular index. " INDEX { aniBsuWirelessPort, aniBsuWirelessFreqAdminIndex } ::= { aniBsuWirelessFreqAdminTable 1 } AniBsuWirelessFreqAdminEntry ::= SEQUENCE { aniBsuWirelessFreqAdminIndex INTEGER, aniBsuWirelessFreqAdminFreqValue DisplayString } aniBsuWirelessFreqAdminIndex OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "The index for this table. " ::= { aniBsuWirelessFreqAdminEntry 1 } aniBsuWirelessFreqAdminFreqValue OBJECT-TYPE SYNTAX DisplayString UNITS "MHz" MAX-ACCESS read-write STATUS current DESCRIPTION "This object is used to configure the desired frequency values for the frequency table. Upto 19 frequency values can be added to the table. All frequencies should belong to the same frequency band. For range and validation, refer to aniBsuWirelessIfConfTargetFrequency description. Once the values are all added/modified, the object aniBsuWirelessIfConfModify (defined in the aniBsuWirelessIfConfTable) needs to be set to true(1). The aniBsuWirelessIfConfModify flag is used to modify and commit the changes of the dependent wireless parameters including all the entries of the aniBsuWirelessFreqAdminTable. If the validation fails when aniBsuWirelessIfConfModify is set to true(1), these changes are not commited and an error is returned. In that case, the modified parameters in this table may not reflect the correct values. They will display the values last configured by the user, rather than the actual values on the device. To view the current values, refer to the aniBsuWirelessFreqOperTable. Each entry in this aniBsuWirelessFreqAdminTable has a corresponding entry displaying the actual values in the aniBsuWirelessFreqOperTable. " ::= { aniBsuWirelessFreqAdminEntry 2 } aniBsuWirelessFreqOperTable OBJECT-TYPE SYNTAX SEQUENCE OF AniBsuWirelessFreqOperEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table is used to view the current frequency table. Each entry in the aniBsuWirelessFreqAdminTable has a corresponding entry in this table. All parameters within this aniBsuWirelessFreqOperTable have read-only access. These objects reflect the actual frequency table values. " ::= { aniBsuWirelessIf 13 } aniBsuWirelessFreqOperEntry OBJECT-TYPE SYNTAX AniBsuWirelessFreqOperEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry containing the frequncy for this particular index. " INDEX { aniBsuWirelessPort, aniBsuWirelessFreqOperIndex } ::= { aniBsuWirelessFreqOperTable 1 } AniBsuWirelessFreqOperEntry ::= SEQUENCE { aniBsuWirelessFreqOperIndex INTEGER, aniBsuWirelessFreqOperFreqValue DisplayString } aniBsuWirelessFreqOperIndex OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "The index for this table. " ::= { aniBsuWirelessFreqOperEntry 1 } aniBsuWirelessFreqOperFreqValue OBJECT-TYPE SYNTAX DisplayString UNITS "MHz" MAX-ACCESS read-only STATUS current DESCRIPTION "This object displays the current frequency value within the frequency table. To change the configuration of the frequency table, use the aniBsuWirelessFreqAdminTable. The correspoding entry with a read-write access for this object is aniBsuWirelessFreqAdminFreqValue. " ::= { aniBsuWirelessFreqOperEntry 2 } -- System level Wireless Parameters (configured per BSU) aniBsuWirelessSysConfGroup OBJECT IDENTIFIER ::= { aniBsuWirelessIf 14 } aniBsuWirelessSysConfBsuId OBJECT-TYPE SYNTAX DisplayString (SIZE (0..38)) MAX-ACCESS read-write STATUS current DESCRIPTION "The unique BSU identifier. This is the BSU ID required for generating seed for frequency reuse support. Note: When this object is changed through SNMP agent, it is required to upload the configuration (set aniDevControlStartUpload in the device_control.mib to true) and then reboot the device for the changes to take effect. " ::= { aniBsuWirelessSysConfGroup 1 } aniBsuWirelessSysConfFrameSize OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total size of the Frame in ticks. " ::= { aniBsuWirelessSysConfGroup 2 } aniBsuWirelessSysConfFrameDownstreamSize OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of ticks in the Downstream portion of the frame. " ::= { aniBsuWirelessSysConfGroup 3 } aniBsuWirelessSysConfFrameUpstreamSize OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of ticks in the Upstream portion of the frame. " ::= { aniBsuWirelessSysConfGroup 4 } aniBsuWirelessSysConfDSUSRatio OBJECT-TYPE SYNTAX INTEGER { ds70-us30(70), ds60-us40(60), ds50-us50(50), ds40-us60(40), ds30-us70(30) } MAX-ACCESS read-only STATUS current DESCRIPTION "The Downstream upstream ratio (DS/US ratio). ds70-us30 is 70/30 ds60-us40 is 60/40 ds50-us50 is 50/50 ds40-us60 is 40/60 ds30-us70 is 30/70 " ::= { aniBsuWirelessSysConfGroup 5 } aniBsuWirelessIfConfTable OBJECT-TYPE SYNTAX SEQUENCE OF AniBsuWirelessIfConfEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table is used to configure the BSU wireless parameters per wireless port. " ::= { aniBsuWirelessIf 15 } aniBsuWirelessIfConfEntry OBJECT-TYPE SYNTAX AniBsuWirelessIfConfEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry for this particular wireless port. " INDEX { aniBsuWirelessPort } ::= { aniBsuWirelessIfConfTable 1 } AniBsuWirelessIfConfEntry ::= SEQUENCE { aniBsuWirelessIfConfTargetFrequency DisplayString, aniBsuWirelessIfConfVerifyAllSu DisplayString, aniBsuWirelessIfConfSwitchToFrequency DisplayString, aniBsuWirelessIfConfModify TruthValue } aniBsuWirelessIfConfTargetFrequency OBJECT-TYPE SYNTAX DisplayString UNITS "MHz" MAX-ACCESS read-write STATUS current DESCRIPTION "The Target Frequency in MHz. Its range depends on Channel Width. 1) 5.3 GHz UNII Band (5250 - 5350 MHz). The center frequencies in this band are within 5250 + Half of Channel Width MHz and 5350 - Half of Channel Width MHz and can have any integer value (in MHz) 2) 5.8 GHz UNII Band (5725 - 5825 MHz). The center frequencies in this band are within 5725 + Half of Channel Width MHz and 5825 - Half of Channel Width MHz and can have any integer value (in MHz). 3) 5.8 GHz General (5650 - 5925 MHz). The center frequencies in this band are within 5650 + Half of Channel Width MHz and 5925 - Half of Channel Width MHz and can have any integer value (in MHz). 4) 2.6 GHz MMDS Band (2500 - 2689 MHz). The center frequencies in this band are 2503 + 6N MHz where N = 0,1,2,.,30 5) 2.6 GHz General (2500 - 2700 MHz). The center frequencies in this band are within 2500 + Half of Channel Width MHz and 2700 - Half of Channel Width MHz and can have any integer value (in MHz). 6) 3.5 GHz General (3300 - 3800 MHz). The center frequencies in this band are within 3300 + Half of Channel Width MHz and 3800 - Half of Channel Width MHz and can have any integer value (in MHz). 7) 3.5 GHz ETSI Band - 50 MHz duplexing Scheme (3410 - 3800 MHz). 8) 3.5 GHz ETSI Band - 100 MHz duplexing scheme (3410 - 3800 MHz). 10) 5.8 GHz ISM Band (5725 - 5850 MHz). The center frequencies in this band are within 5725 + Half of Channel Width MHz and 5850 - Half of Channel Width MHz and can have any integer value (in MHz). 11) 5.3 GHz General Band (5150 - 5350 MHz). The center frequencies in this band are within 5150 + Half of Channel Width MHz and 5350 - Half of Channel Width MHz and can have any integer value (in MHz) Note: The term Half of Channel Width in all the descriptions above, is a rounded off value (with 0.5 rounded to 1). Note: When this object is changed through SNMP agent, the value could take effect immediately depending on the current channel center frequency value. If aniBsuWirelessIfConfTargetFrequency is modified, but the current aniBsuChannelFrequency value is still one of the entries in aniBsuWirelessFreqOperTable, then the target frequency will not take effect immediately. However it could take effect later on when the current frequency entry is deleted from the frequency table. " ::= { aniBsuWirelessIfConfEntry 1 } aniBsuWirelessIfConfVerifyAllSu OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "This flag is used to verify if the current set of BSU wireless parameters, that is, aniBsuWirelessPtPConfChannelWidth, aniBsuWirelessPtPConfTargetFrequency, aniBsuWirelessPtPConfBsuId are correctly configured on all the SUs connected. The values are compared against all the SUs connected to this BSU. Sending a Get request on this object causes the agent to verify the above set of parameters. If these set of values are incorrect, an error string is returned indicating that some values are not in sync. If the current set of values are correct, then the string 'No error' is displayed. This object might require upto 10 seconds to respond if multiple SUs are connected. Therefore, to ensure that it does not timeout before getting the complete results, the SNMP Manager tool should increase it's timeout value for this object to more than 10 seconds. " ::= { aniBsuWirelessIfConfEntry 2 } aniBsuWirelessIfConfSwitchToFrequency OBJECT-TYPE SYNTAX DisplayString UNITS "MHz" MAX-ACCESS read-write STATUS current DESCRIPTION "The Frequency selected to be switched. This frequency should be either one of the frequency entries in the aniBsuWirelessFreqOperTable or the current target frequency aniBsuTargetFrequency. A get request on this object will display the current frequency, aniBsuChannelFrequency and if no radio is detected, it will display 0.00. " ::= { aniBsuWirelessIfConfEntry 3 } aniBsuWirelessIfConfModify OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "This flag is used to modify and commit the changes of the dependent parameters from this group: aniBsuWirelessIfConfTargetFrequency aniBsuWirelessFreqAdminTable Setting this object to true(1) causes the agent to validate the entire set of parameters. If these set of values are acceptable, then the new values are changed on the device. However, for the changes to take effect, it is required to upload the configuration (set aniDevControlStartUpload in the device_control.mib to true) and then reboot the device. If the validation fails when aniBsuWirelessIfConfModify is set to true(1), the changes are not commited and an error is returned. In that case, the modified parameters in this group may not reflect the correct values. They will display the values last configured by the user, rather than the current values on the device. To view the current values for aniBsuWirelessIfConfTargetFrequency refer to aniBsuTargetFrequency aniBsuWirelessFreqAdminTable refer to aniBsuWirelessFreqOperTable A Get request on this object will always return false(2). " ::= { aniBsuWirelessIfConfEntry 50 } aniBsuWirelessAFSTable OBJECT-TYPE SYNTAX SEQUENCE OF AniBsuWirelessAFSConfEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table is used to configure the BSU wireless AFS parameters per wireless port. " ::= { aniBsuWirelessIf 16 } aniBsuWirelessAFSConfEntry OBJECT-TYPE SYNTAX AniBsuWirelessAFSConfEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry for this particular wireless port. " INDEX { aniBsuWirelessPort } ::= { aniBsuWirelessAFSTable 1 } AniBsuWirelessAFSConfEntry ::= SEQUENCE { aniBsuWirelessAFSFlag INTEGER, aniBsuWirelessAFSMinSwitchDuration INTEGER, aniBsuWirelessAFSMinNotificationDuration INTEGER, aniBsuWirelessAFSErrPercentage INTEGER, aniBsuWirelessAFSMinSwitchBytes INTEGER } aniBsuWirelessAFSFlag OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Enable or disable AFS. " ::= { aniBsuWirelessAFSConfEntry 1 } aniBsuWirelessAFSMinSwitchDuration OBJECT-TYPE SYNTAX INTEGER (1..600) MAX-ACCESS read-write STATUS current DESCRIPTION "Configure AFS minimum switch duration in database (second) " ::= { aniBsuWirelessAFSConfEntry 2 } aniBsuWirelessAFSMinNotificationDuration OBJECT-TYPE SYNTAX INTEGER (1..540) MAX-ACCESS read-write STATUS current DESCRIPTION "Configure AFS minimum notification duration (second) " ::= { aniBsuWirelessAFSConfEntry 3 } aniBsuWirelessAFSErrPercentage OBJECT-TYPE SYNTAX INTEGER (1..100) MAX-ACCESS read-write STATUS current DESCRIPTION "Configure AFS minimum error percentage. " ::= { aniBsuWirelessAFSConfEntry 4 } aniBsuWirelessAFSMinSwitchBytes OBJECT-TYPE SYNTAX INTEGER (1000..20000) MAX-ACCESS read-write STATUS current DESCRIPTION "Configure AFS minimum switch bytes. " ::= { aniBsuWirelessAFSConfEntry 5 } END