-- ***************************************************************** -- BSTUN-MIB.my: Blocked Serial Tunnel MIB file -- -- Nov 1994, Derek Bolton -- Jan 1995, Sandy Logie -- -- Copyright (c) 1995-1997, 2001, 2003 by cisco Systems, Inc. -- Prepared by Metaplex -- All rights reserved. -- -- ***************************************************************** CISCO-BSTUN-MIB DEFINITIONS ::= BEGIN IMPORTS MODULE-IDENTITY, OBJECT-TYPE, NOTIFICATION-TYPE, Counter32, Integer32, IpAddress FROM SNMPv2-SMI MODULE-COMPLIANCE, OBJECT-GROUP, NOTIFICATION-GROUP FROM SNMPv2-CONF ifIndex, InterfaceIndex FROM IF-MIB TruthValue FROM SNMPv2-TC ciscoMgmt FROM CISCO-SMI; ciscoBstunMIB MODULE-IDENTITY LAST-UPDATED "200302100000Z" ORGANIZATION "Cisco Systems, Inc." CONTACT-INFO " Cisco Systems Customer Service Postal: 170 W. Tasman Drive San Jose, CA 95134 USA Tel: +1 800 553-NETS E-mail: cs-bisync@cisco.com" DESCRIPTION "The MIB module for Block Serial Tunneling. Overview of BSTUN MIB MIB description The BSTUN MIB provides the configuration and operational information on Cisco's blocked serial tunnelling implementation. The following entities are managed: 1) Global BSTUN information 2) BSTUN groups 3) BSTUN ports 4) BSTUN routes The following example configuration shows how the BSTUN MIB returns BSTUN information, from either CISCO A or CISCO B. HOST == BSC == Cisco A == IP Network == Cisco B == BSC == BSC line line device 1) The BSTUN global entry identifies the IP address by which the router is known to other BSTUN peers, a configurable SAP value on which to listen to LLC2 peers, and keepalive values to maintain a session between TCP/IP peers. 2) The BSTUN group table identifies the BSTUN group number and protocol type that Cisco A and Cisco B use to route BSC traffic over the IP network. The table contains an entry for each BSTUN group defined on the router. (The group number must be the same in Cisco A and Cisco B, for traffic to flow from one router to the other.) 3) The BSTUN port table identifies the serial interface to the BSC line for which the router is doing serial tunnelling. The MIB also identifies the BSTUN group this interface is defined for, and identifies the default routing for unrecognized BSC addresses. There is a port entry for each BSTUN-enabled interface on the router. 4) The BSTUN route table has an entry for each address defined for routing within the BSTUN group, and an entry for the default routing if the 'bstun route all' command is configured. The route entry includes identification of the BSTUN peer, priority, state, and packet and byte counters. " REVISION "200302100000Z" DESCRIPTION "Added Asynchronous POS to IP conversion support" REVISION "200106190000Z" DESCRIPTION "Added Bisync to IP conversion peer support" REVISION "9701220000Z" DESCRIPTION "Added frame-relay and other support" REVISION "9508210000Z" DESCRIPTION "Minor cleanups to pacify mib compiler." ::= { ciscoMgmt 35 } bstunObjects OBJECT IDENTIFIER ::= { ciscoBstunMIB 1} bstunGlobal OBJECT IDENTIFIER ::= { bstunObjects 1} bstunGroups OBJECT IDENTIFIER ::= { bstunObjects 2} bstunPorts OBJECT IDENTIFIER ::= { bstunObjects 3} bstunRoutes OBJECT IDENTIFIER ::= { bstunObjects 4} -- ********************************************************************* -- * global values for router -- ********************************************************************* bstunIPAddr OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The configured IP address used by the BSTUN component in this router." ::= { bstunGlobal 1 } bstunLisnSap OBJECT-TYPE SYNTAX Integer32 (1..255) MAX-ACCESS read-only STATUS current DESCRIPTION "The configured Listening SAP address used by the BSTUN component when routed via frame-relay local-ack in this router." ::= { bstunGlobal 2 } bstunPeerKeepaliveInterval OBJECT-TYPE SYNTAX Integer32 (1..300) UNITS "deciseconds" MAX-ACCESS read-only STATUS current DESCRIPTION "The time interval between keepalives in this router." ::= { bstunGlobal 3 } bstunPeerKeepaliveLimit OBJECT-TYPE SYNTAX Integer32 (2..10) MAX-ACCESS read-only STATUS current DESCRIPTION "The number of keepalives which can be missed in a continuous interval before session declared down in this router." ::= { bstunGlobal 4 } -- ********************************************************************* -- * bstun Group Table -- ********************************************************************* bstunGroupTable OBJECT-TYPE SYNTAX SEQUENCE OF BstunGroupEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table of entries representing BSTUN groups configured on the router. Each BSTUN-enabled interface is assigned to a BSTUN group, and packets can only travel between BSTUN-enabled interfaces in the same group." ::= { bstunGroups 1 } bstunGroupEntry OBJECT-TYPE SYNTAX BstunGroupEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Status and parameter values for a group." INDEX { bstunGroupIndex } ::= { bstunGroupTable 1 } BstunGroupEntry ::= SEQUENCE { bstunGroupIndex INTEGER, bstunProtocolType INTEGER, bstunLocalAck TruthValue, bstunGroupUnroutableTransmit Counter32, bstunGroupUnroutableReceive Counter32 } bstunGroupIndex OBJECT-TYPE SYNTAX INTEGER (1..255) MAX-ACCESS not-accessible STATUS current DESCRIPTION "The configured BSTUN group number. The significance of this number is that it must match the BSTUN group number configured in the router at the other end of the BSTUN tunnel." ::= { bstunGroupEntry 1 } bstunProtocolType OBJECT-TYPE SYNTAX INTEGER { bsc(1), -- Binary Synchronous Communications adtVariPoll(2), adtPollSelect(3), adplex(4), diebold(5), asyncGeneric(6), mdi(7), mosec(8), gddb(9), apos(10) } MAX-ACCESS read-only STATUS current DESCRIPTION "The protocol type for this BSTUN group." ::= { bstunGroupEntry 2 } bstunLocalAck OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates if the BSTUN connection is locally acknowledged. TRUE-> BSTUN connection is locally acknowledged FALSE-> BSTUN connection is not locally acknowledged " ::= { bstunGroupEntry 3 } bstunGroupUnroutableTransmit OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of unroutable frames received by this group from the remote partner. They were unroutable because the address was not recognized; that is there is no bstun route command configured for this address. This indicates that the configuration in this router is incompatible with the peer router." ::= { bstunGroupEntry 4 } bstunGroupUnroutableReceive OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Count of frames received from a serial interface with an unsupported poll address. Note that there may be several ports configured within this bstun group; a non-zero value in this field indicates that a least one of these ports is receiving frames for which there are no bstun route commands configured. This indicates that the configuration in this router is incompatible with the configuration in at least one of the attached devices." ::= { bstunGroupEntry 5 } -- ********************************************************************* -- * bstun Port Table -- ********************************************************************* bstunPortTable OBJECT-TYPE SYNTAX SEQUENCE OF BstunPortEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A list of BSTUN-enabled interfaces (ports)." ::= { bstunPorts 1 } bstunPortEntry OBJECT-TYPE SYNTAX BstunPortEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Status and parameter values for a BSTUN port." INDEX { ifIndex } ::= { bstunPortTable 1 } BstunPortEntry ::= SEQUENCE { bstunPortGroupNumber INTEGER, bstunPortDefaultPeerType INTEGER, bstunPortDefaultPeerIP IpAddress, bstunPortDefaultPeerSerial InterfaceIndex } bstunPortGroupNumber OBJECT-TYPE SYNTAX INTEGER (1..255) MAX-ACCESS read-only STATUS current DESCRIPTION "The group number to which the bstun port belongs. Frames will only be routed to other ports (on this or another router) in the same bstun group. This group should match a bstunGroupIndex in the bstunGroupTable." ::= { bstunPortEntry 1 } bstunPortDefaultPeerType OBJECT-TYPE SYNTAX INTEGER { none(1), ip(2), serial(3), serialDirect(4), serialFrameRelay(5), serialLLC2(6) } MAX-ACCESS read-only STATUS current DESCRIPTION "The type of identification of the remote default partner. (This is as configured with the 'route all' command.) If ip then the value is in bstunPortDefaultPeerIP; if serial or serialDirect then the value is in bstunPortDefaultPeerSerial." ::= { bstunPortEntry 2 } bstunPortDefaultPeerIP OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The ip address of the remote default BSTUN partner, for unrecognized addresses. 0.0.0.0 if partner address type is not ip." ::= { bstunPortEntry 3 } bstunPortDefaultPeerSerial OBJECT-TYPE SYNTAX InterfaceIndex MAX-ACCESS read-only STATUS current DESCRIPTION "If bstunRouteType is serial then this is the serial interface index of the point-to-point link to the remote partner; if bstunRouteType is serialDirect then the partner is in the local BSTUN. if bstunRouteType is ip then this field is 0." ::= { bstunPortEntry 4 } -- ********************************************************************* -- * Route Table -- ********************************************************************* bstunRouteTable OBJECT-TYPE SYNTAX SEQUENCE OF BstunRouteEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table containing information about specific poll addresses. There is one table entry for each address configured by the BSTUN ROUTE command." ::= { bstunRoutes 1 } bstunRouteEntry OBJECT-TYPE SYNTAX BstunRouteEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The information regarding a single poll address." INDEX { bstunRouteGroupIndex, bstunRouteStationAddress } ::= { bstunRouteTable 1 } BstunRouteEntry ::= SEQUENCE { bstunRouteGroupIndex INTEGER, bstunRouteStationAddress INTEGER, bstunRouteType INTEGER, bstunRouteIP IpAddress, bstunRouteSerial InterfaceIndex, bstunRoutePriority INTEGER, bstunRoutePeerState INTEGER, bstunRouteRxPackets Counter32, bstunRouteTxPackets Counter32, bstunRouteRxBytes Counter32, bstunRouteTxBytes Counter32, bstunRouteDLCI Integer32, bstunRouteRSAP Integer32, bstunLLC2Priority Integer32, bstunRouteBIPPassive TruthValue, bstunRouteBIPLocalPort Integer32, bstunRouteBIPForeignPort Integer32, bstunRouteBIPDeviceStatus BITS, bstunRouteAPIPHeaderVersion INTEGER } bstunRouteGroupIndex OBJECT-TYPE SYNTAX INTEGER (1..255) MAX-ACCESS not-accessible STATUS current DESCRIPTION "The index of the BSTUN Group owning this station." ::= { bstunRouteEntry 1 } bstunRouteStationAddress OBJECT-TYPE SYNTAX INTEGER (1..256) MAX-ACCESS not-accessible STATUS current DESCRIPTION "The poll address of the station. 256 indicates the ALL parameter on the STUN ROUTE command, which is the route for all unrecognized addresses." ::= { bstunRouteEntry 2 } bstunRouteType OBJECT-TYPE SYNTAX INTEGER { none(1), ip(2), serial(3), serialDirect(4), serialFrameRelay(5), serialLLC2(6), bip(7), apip(8) } MAX-ACCESS read-only STATUS current DESCRIPTION "The type of identification of the remote partner. If ip then the value is in bstunRouteIP; if serial or serialDirect then the value is in bstunRouteSerial; if bip or apip then the value is in bstunRouteIP, bstunRouteBIPLocalPort and bstunRouteBIPForeignPort." ::= { bstunRouteEntry 3 } bstunRouteIP OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The ip address of the remote BSTUN partner. 0.0.0.0 if partner address type is not ip." ::= { bstunRouteEntry 4 } bstunRouteSerial OBJECT-TYPE SYNTAX InterfaceIndex MAX-ACCESS read-only STATUS current DESCRIPTION "If bstunRouteType is serial then this is the serial interface index of the point-to-point link to the remote partner; if bstunRouteType is serialDirect then the partner is in the local BSTUN. if bstunRouteType is ip then this field is 0." ::= { bstunRouteEntry 5 } bstunRoutePriority OBJECT-TYPE SYNTAX INTEGER {low(1), normal(2), medium(3), high(4)} MAX-ACCESS read-only STATUS current DESCRIPTION "The priority with which this station's traffic will be routed across the network." ::= { bstunRouteEntry 6 } bstunRoutePeerState OBJECT-TYPE SYNTAX INTEGER {dead(1), closed(2), opening(3), openWait(4), connected(5), direct(6)} MAX-ACCESS read-only STATUS current DESCRIPTION "The state of the peer connection through the BSTUN tunnel." ::= { bstunRouteEntry 7 } bstunRouteRxPackets OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Count of frames received from the serial interface with this station's address." ::= { bstunRouteEntry 8 } bstunRouteTxPackets OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Count of frames transmitted at the serial interface with this station's address." ::= { bstunRouteEntry 9 } bstunRouteRxBytes OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Count of bytes received from the serial interface with this station's address." ::= { bstunRouteEntry 10 } bstunRouteTxBytes OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Count of bytes transmitted at the serial interface with this station's address." ::= { bstunRouteEntry 11 } bstunRouteDLCI OBJECT-TYPE SYNTAX Integer32 (16..1007) MAX-ACCESS read-only STATUS current DESCRIPTION "If bstunRouteType is serialFrameRelay or serialLLC2 then this is the frame relay dlci circuit used for the point-to-point link to the remote partner; if bstunRouteType is ip or serial then this field is 0." ::= { bstunRouteEntry 12 } bstunRouteRSAP OBJECT-TYPE SYNTAX Integer32 (1..255) MAX-ACCESS read-only STATUS current DESCRIPTION "If bstunRouteType is serialLLC2 then this is the llc2 sap value used for the point-to-point link to the remote partner; if bstunRouteType is ip or serial or serialFrameRelay then this field is 0." ::= { bstunRouteEntry 13 } bstunLLC2Priority OBJECT-TYPE SYNTAX Integer32 (1..10) MAX-ACCESS read-only STATUS current DESCRIPTION "If bstunRouteType is serialLLC2 then this is the llc2 priority used for the point-to-point link to the remote partner; if bstunRouteType is ip or serial or serialFrameRelay then this field is 0." ::= { bstunRouteEntry 14 } bstunRouteBIPPassive OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION "Specifies whether the bip peer will wait for an inbound connection or actively connect to the remote peer." DEFVAL { false } ::= { bstunRouteEntry 15 } bstunRouteBIPLocalPort OBJECT-TYPE SYNTAX Integer32 (1025..32000) MAX-ACCESS read-only STATUS current DESCRIPTION "If bstunRouteType is bip then this is the local port used when connecting to the remote peer." ::= { bstunRouteEntry 16 } bstunRouteBIPForeignPort OBJECT-TYPE SYNTAX Integer32 (1025..32000) MAX-ACCESS read-only STATUS current DESCRIPTION "If bstunRouteType is bip then this is the for port used to connect to the remote peer." ::= { bstunRouteEntry 17 } bstunRouteBIPDeviceStatus OBJECT-TYPE SYNTAX BITS { operationcheck(0), reservedBit1(1), datacheck(2), equipmentcheck(3), interventionrequired(4), commandreject(5), deviceinactive(6), deviceactive(7), reservedBit8(8), deviceend(9), unitspecify(10), devicebusy(11) } MAX-ACCESS read-only STATUS current DESCRIPTION "If bstunRouteType is bip then this indicates the OR bit mask status of the mapped bisync device: if no bits are set, indicates that the bisync device is up and operational. Bit 0, if set, indicates that the bisync device is reporting an operation check error. Bit 2, if set, indicates that the bisync device is reporting a data check error. Bit 3, if set, indicates that the bisync device is reporting an equipment check error. Bit 4, if set, indicates that the bisync device is reporting that intervention is required. Bit 5, if set, indicates that the bisync device is reporting that a command has been rejected. Bit 6, if set, indicates that the bisync device is not responding to polls. Bit 7, if set, indicates that the bisync device is now responding to polls and is operational. Bit 9, if set, indicates that the bisync device is reporting that is no longer busy. Bit 10, if set, indicates that the bisync device is reporting a device unit specify. Bit 11, if set, indicates that the bisync device is reporting a busy condition." ::= { bstunRouteEntry 18 } bstunRouteAPIPHeaderVersion OBJECT-TYPE SYNTAX INTEGER {v0(1), v1(2), v2(3)} MAX-ACCESS read-only STATUS current DESCRIPTION "Specifies the tunneling header format to use for APIP: v0, if set, indicates a 2 byte encapsulation header. The length of the header is included in the size of the sent packet. v1, if set, indicates a 2 byte encapsulation header. The length of the header is excluded from the size of the sent packet. v2, if set, indicates a 4 byte encapsulation header. The length of the header is excluded from the size of the sent packet." ::= { bstunRouteEntry 19 } -- ************************************************************************* -- * BSTUN notifications -- ************************************************************************* bstunNotificationPrefix OBJECT IDENTIFIER ::= { ciscoBstunMIB 2 } bstunNotifications OBJECT IDENTIFIER ::= { bstunNotificationPrefix 0 } bstunPeerStateChangeNotification NOTIFICATION-TYPE OBJECTS { bstunRoutePeerState } STATUS deprecated DESCRIPTION "This notification indicates that the state of a BSTUN route has transitioned to active (connected) or inactive (dead or closed)." ::= { bstunNotifications 1 } bstunPeerStateChangeNotification2 NOTIFICATION-TYPE OBJECTS { bstunRoutePeerState, bstunRouteType, bstunRouteRxPackets, bstunRouteTxPackets } STATUS current DESCRIPTION "This notification indicates that the state of a BSTUN route has transitioned to active (connected) or inactive (dead or closed)." ::= { bstunNotifications 2 } bstunCUStatusChangeNotification NOTIFICATION-TYPE OBJECTS { bstunRouteIP, bstunRouteBIPForeignPort, bstunRouteBIPLocalPort, bstunRouteBIPDeviceStatus } STATUS current DESCRIPTION "This notification is generated when a mapped BIP bisync device state has changed." ::= { bstunNotifications 3 } -- ************************************************************************* -- * Conformance Information -- ************************************************************************* -- bstunMibConformance OBJECT IDENTIFIER ::= { ciscoBstunMIB 3 } bstunMibCompliances OBJECT IDENTIFIER ::= { bstunMibConformance 1 } bstunMibGroups OBJECT IDENTIFIER ::= { bstunMibConformance 2 } -- -- ************************************************************************* -- * Compliance Statements -- ************************************************************************* bstunMibCompliance MODULE-COMPLIANCE STATUS obsolete -- superceded by bstunMibComplianceRev1 DESCRIPTION "The compliance statement for BSTUN." MODULE -- this module MANDATORY-GROUPS { bstunGlobalGroup, bstunGroupGroup, bstunPortGroup, bstunRouteGroup } ::= { bstunMibCompliances 1 } bstunMibComplianceRev1 MODULE-COMPLIANCE STATUS obsolete DESCRIPTION "The compliance statement for all Cisco systems that implement BSTUN functions." MODULE -- this module MANDATORY-GROUPS { bstunGlobalGroupRev1, bstunGroupGroup, bstunPortGroup, bstunRouteGroupRev1 } ::= { bstunMibCompliances 2 } bstunMibComplianceRev2 MODULE-COMPLIANCE STATUS deprecated DESCRIPTION "The compliance statement for all Cisco systems that implement BSTUN functions." MODULE -- this module MANDATORY-GROUPS { bstunGlobalGroupRev1, bstunGroupGroup, bstunPortGroup, bstunRouteGroupRev2, bstunNotificationGroupRev1 } ::= { bstunMibCompliances 3 } bstunMibComplianceRev3 MODULE-COMPLIANCE STATUS current DESCRIPTION "The compliance statement for all Cisco systems that implement BSTUN functions." MODULE -- this module MANDATORY-GROUPS { bstunGlobalGroupRev1, bstunGroupGroup, bstunPortGroup, bstunRouteGroupRev1, bstunNotificationGroupRev1 } GROUP bstunRouteBipGroup DESCRIPTION "This group is mandatory when implementing the bip route type." GROUP bstunRoutePortsGroup DESCRIPTION "This group is mandatory when implementing the bip or apip route types." GROUP bstunRouteApipGroup DESCRIPTION "This group is mandatory when implementing the apip route type." ::= { bstunMibCompliances 4 } bstunGlobalGroup OBJECT-GROUP OBJECTS { bstunIPAddr } STATUS obsolete -- superceded by bstunGlobalGroupRev1 DESCRIPTION "A collection of objects providing global BSTUN information." ::= { bstunMibGroups 1} bstunGroupGroup OBJECT-GROUP OBJECTS { bstunProtocolType, bstunLocalAck, bstunGroupUnroutableTransmit, bstunGroupUnroutableReceive } STATUS current DESCRIPTION "A collection of objects providing information about BSTUN groups ." ::= { bstunMibGroups 2 } bstunPortGroup OBJECT-GROUP OBJECTS { bstunPortGroupNumber, bstunPortDefaultPeerType, bstunPortDefaultPeerIP, bstunPortDefaultPeerSerial } STATUS current DESCRIPTION "A collection of objects providing information about BSTUN enabled interfaces." ::= { bstunMibGroups 3} bstunRouteGroup OBJECT-GROUP OBJECTS { bstunRouteType, bstunRouteIP, bstunRouteSerial, bstunRoutePriority, bstunRoutePeerState, bstunRouteRxPackets, bstunRouteTxPackets, bstunRouteRxBytes, bstunRouteTxBytes } STATUS obsolete -- superceded by bstunRouteGroupRev1 DESCRIPTION "A collection of objects providing information about BSTUN defined routes." ::= { bstunMibGroups 4} bstunGlobalGroupRev1 OBJECT-GROUP OBJECTS { bstunIPAddr, bstunLisnSap, bstunPeerKeepaliveInterval, bstunPeerKeepaliveLimit } STATUS current DESCRIPTION "A collection of objects providing global BSTUN information." ::= { bstunMibGroups 5} bstunRouteGroupRev1 OBJECT-GROUP OBJECTS { bstunRouteType, bstunRouteIP, bstunRouteSerial, bstunRoutePriority, bstunRoutePeerState, bstunRouteRxPackets, bstunRouteTxPackets, bstunRouteRxBytes, bstunRouteTxBytes, bstunRouteDLCI, bstunRouteRSAP, bstunLLC2Priority } STATUS current DESCRIPTION "A collection of objects providing information about BSTUN defined routes." ::= { bstunMibGroups 6} bstunRouteGroupRev2 OBJECT-GROUP OBJECTS { bstunRouteType, bstunRouteIP, bstunRouteSerial, bstunRoutePriority, bstunRoutePeerState, bstunRouteRxPackets, bstunRouteTxPackets, bstunRouteRxBytes, bstunRouteTxBytes, bstunRouteDLCI, bstunRouteRSAP, bstunLLC2Priority, bstunRouteBIPPassive, bstunRouteBIPLocalPort, bstunRouteBIPForeignPort, bstunRouteBIPDeviceStatus } STATUS deprecated DESCRIPTION "A collection of objects providing information about BSTUN defined routes." ::= { bstunMibGroups 7} bstunNotificationGroup NOTIFICATION-GROUP NOTIFICATIONS { bstunPeerStateChangeNotification } STATUS deprecated DESCRIPTION "A collection of notifications. " ::= { bstunMibGroups 8 } bstunNotificationGroupRev1 NOTIFICATION-GROUP NOTIFICATIONS { bstunPeerStateChangeNotification2, bstunCUStatusChangeNotification } STATUS current DESCRIPTION "A collection of notifications. " ::= { bstunMibGroups 9 } bstunRouteBipGroup OBJECT-GROUP OBJECTS { bstunRouteBIPPassive, bstunRouteBIPDeviceStatus } STATUS current DESCRIPTION "A objects providing information about BSTUN defined routes for BIP protocol." ::= { bstunMibGroups 10} bstunRoutePortsGroup OBJECT-GROUP OBJECTS { bstunRouteBIPLocalPort, bstunRouteBIPForeignPort } STATUS current DESCRIPTION "A objects providing port number informaton information about BSTUN defined routes for BIP and APIP protocols." ::= { bstunMibGroups 11} bstunRouteApipGroup OBJECT-GROUP OBJECTS { bstunRouteAPIPHeaderVersion } STATUS current DESCRIPTION "A objects providing information about BSTUN defined routes for APIP protocol." ::= { bstunMibGroups 12} END