-- ***************************************************************** -- CISCO-MEMORY-POOL-MIB -- -- February 1996, Jeffrey T. Johnson -- -- July 2001, Seth Wang -- -- Copyright (c) 2001 by cisco Systems, Inc. -- All rights reserved. -- ***************************************************************** CISCO-MEMORY-POOL-MIB DEFINITIONS ::= BEGIN IMPORTS MODULE-IDENTITY, OBJECT-TYPE, Integer32, Gauge32 FROM SNMPv2-SMI TEXTUAL-CONVENTION, DisplayString, TruthValue FROM SNMPv2-TC MODULE-COMPLIANCE, OBJECT-GROUP FROM SNMPv2-CONF ciscoMgmt FROM CISCO-SMI Percent FROM CISCO-QOS-PIB-MIB; ciscoMemoryPoolMIB MODULE-IDENTITY LAST-UPDATED "200107310000Z" ORGANIZATION "Cisco Systems, Inc." CONTACT-INFO "Postal: Cisco Systems, Inc. 170 West Tasman Drive San Jose, CA 95134-1706 USA Tel: +1 408 526 4000 E-mail: cs-snmp@cisco.com" DESCRIPTION "MIB module for monitoring memory pools" REVISION "200107310000Z" DESCRIPTION "Added a new table, ciscoMemoryPoolUtilizationTable, which provides information about memory utilization." REVISION "199602010000Z" DESCRIPTION "Initial version of this MIB module." ::= { ciscoMgmt 48 } CiscoMemoryPoolTypes ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "Represents the different types of memory pools that may be present in a managed device. Memory pools can be roughly categorized into two groups, predefined pools and dynamic pools. The following pool types are currently predefined: 1: processor memory 2: i/o memory 3: pci memory 4: fast memory 5: multibus memory Dynamic pools will have a pool type value greater than any of the predefined types listed above. Note that only the processor pool is required to be supported by all devices. Support for other pool types is dependent on the device being managed." SYNTAX Integer32 (1..65535) ciscoMemoryPoolObjects OBJECT IDENTIFIER ::= { ciscoMemoryPoolMIB 1 } ciscoMemoryPoolTable OBJECT-TYPE SYNTAX SEQUENCE OF CiscoMemoryPoolEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table of memory pool monitoring entries." ::= { ciscoMemoryPoolObjects 1 } ciscoMemoryPoolEntry OBJECT-TYPE SYNTAX CiscoMemoryPoolEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in the memory pool monitoring table." INDEX { ciscoMemoryPoolType } ::= { ciscoMemoryPoolTable 1 } CiscoMemoryPoolEntry ::= SEQUENCE { ciscoMemoryPoolType CiscoMemoryPoolTypes, ciscoMemoryPoolName DisplayString, ciscoMemoryPoolAlternate Integer32, ciscoMemoryPoolValid TruthValue, ciscoMemoryPoolUsed Gauge32, ciscoMemoryPoolFree Gauge32, ciscoMemoryPoolLargestFree Gauge32 } ciscoMemoryPoolType OBJECT-TYPE SYNTAX CiscoMemoryPoolTypes MAX-ACCESS not-accessible STATUS current DESCRIPTION "The type of memory pool for which this entry contains information." ::= { ciscoMemoryPoolEntry 1 } ciscoMemoryPoolName OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "A textual name assigned to the memory pool. This object is suitable for output to a human operator, and may also be used to distinguish among the various pool types, especially among dynamic pools." ::= { ciscoMemoryPoolEntry 2 } ciscoMemoryPoolAlternate OBJECT-TYPE SYNTAX Integer32 (0..65535) MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates whether or not this memory pool has an alternate pool configured. Alternate pools are used for fallback when the current pool runs out of memory. If an instance of this object has a value of zero, then this pool does not have an alternate. Otherwise the value of this object is the same as the value of ciscoMemoryPoolType of the alternate pool." ::= { ciscoMemoryPoolEntry 3 } ciscoMemoryPoolValid OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates whether or not the remaining objects in this entry contain accurate data. If an instance of this object has the value false (which in and of itself indicates an internal error condition), the values of the remaining objects in the conceptual row may contain inaccurate information (specifically, the reported values may be less than the actual values)." ::= { ciscoMemoryPoolEntry 4 } ciscoMemoryPoolUsed OBJECT-TYPE SYNTAX Gauge32 UNITS "bytes" MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates the number of bytes from the memory pool that are currently in use by applications on the managed device." ::= { ciscoMemoryPoolEntry 5 } ciscoMemoryPoolFree OBJECT-TYPE SYNTAX Gauge32 UNITS "bytes" MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates the number of bytes from the memory pool that are currently unused on the managed device. Note that the sum of ciscoMemoryPoolUsed and ciscoMemoryPoolFree is the total amount of memory in the pool" ::= { ciscoMemoryPoolEntry 6 } ciscoMemoryPoolLargestFree OBJECT-TYPE SYNTAX Gauge32 UNITS "bytes" MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates the largest number of contiguous bytes from the memory pool that are currently unused on the managed device." ::= { ciscoMemoryPoolEntry 7 } ciscoMemoryPoolUtilizationTable OBJECT-TYPE SYNTAX SEQUENCE OF CiscoMemoryPoolUtilizationEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table of memory pool utilization entries. Each of the objects provides a general idea of how much of the memory pool has been used over a given period of time. It is determined as a weighted decaying average." ::= { ciscoMemoryPoolObjects 2 } ciscoMemoryPoolUtilizationEntry OBJECT-TYPE SYNTAX CiscoMemoryPoolUtilizationEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in the memory pool utilization table." AUGMENTS { ciscoMemoryPoolEntry } ::= { ciscoMemoryPoolUtilizationTable 1 } CiscoMemoryPoolUtilizationEntry ::= SEQUENCE { ciscoMemoryPoolUtilization1Min Percent, ciscoMemoryPoolUtilization5Min Percent, ciscoMemoryPoolUtilization10Min Percent } ciscoMemoryPoolUtilization1Min OBJECT-TYPE SYNTAX Percent MAX-ACCESS read-only STATUS current DESCRIPTION "This is the memory pool utilization for 1 minute." ::= { ciscoMemoryPoolUtilizationEntry 1 } ciscoMemoryPoolUtilization5Min OBJECT-TYPE SYNTAX Percent MAX-ACCESS read-only STATUS current DESCRIPTION "This is the memory pool utilization for 5 minutes." ::= { ciscoMemoryPoolUtilizationEntry 2 } ciscoMemoryPoolUtilization10Min OBJECT-TYPE SYNTAX Percent MAX-ACCESS read-only STATUS current DESCRIPTION "This is the memory pool utilization for 10 minutes." ::= { ciscoMemoryPoolUtilizationEntry 3 } -- notifications ciscoMemoryPoolNotifications OBJECT IDENTIFIER ::= { ciscoMemoryPoolMIB 2 } -- (no notifications are currently defined) -- conformance information ciscoMemoryPoolConformance OBJECT IDENTIFIER ::= { ciscoMemoryPoolMIB 3 } ciscoMemoryPoolCompliances OBJECT IDENTIFIER ::= { ciscoMemoryPoolConformance 1 } ciscoMemoryPoolGroups OBJECT IDENTIFIER ::= { ciscoMemoryPoolConformance 2 } -- compliance statements ciscoMemoryPoolCompliance MODULE-COMPLIANCE STATUS deprecated -- superceded by ciscoMemoryPoolComplianceRev1 DESCRIPTION "The compliance statement for entities which implement the Cisco Memory Pool MIB" MODULE -- this module MANDATORY-GROUPS { ciscoMemoryPoolGroup } ::= { ciscoMemoryPoolCompliances 1 } ciscoMemoryPoolComplianceRev1 MODULE-COMPLIANCE STATUS current DESCRIPTION "The compliance statement for entities which implement the Cisco Memory Pool MIB" MODULE -- this module MANDATORY-GROUPS { ciscoMemoryPoolGroup } GROUP ciscoMemoryPoolUtilizationGroup DESCRIPTION "Per memory pool utilization statistics is mandatory for the managed system that supports memory pool utilization." ::= { ciscoMemoryPoolCompliances 2 } -- units of conformance ciscoMemoryPoolGroup OBJECT-GROUP OBJECTS { ciscoMemoryPoolName, ciscoMemoryPoolAlternate, ciscoMemoryPoolValid, ciscoMemoryPoolUsed, ciscoMemoryPoolFree, ciscoMemoryPoolLargestFree } STATUS current DESCRIPTION "A collection of objects providing memory pool monitoring." ::= { ciscoMemoryPoolGroups 1 } ciscoMemoryPoolUtilizationGroup OBJECT-GROUP OBJECTS { ciscoMemoryPoolUtilization1Min, ciscoMemoryPoolUtilization5Min, ciscoMemoryPoolUtilization10Min } STATUS current DESCRIPTION "An optional group providing a collection of memory pool utilization objects." ::= { ciscoMemoryPoolGroups 2 } END