EXTREME-WIRELESS-MIB DEFINITIONS ::= BEGIN IMPORTS ifIndex FROM IF-MIB InterfaceIndex FROM IF-MIB MODULE-IDENTITY FROM SNMPv2-SMI OBJECT-TYPE FROM SNMPv2-SMI NOTIFICATION-TYPE FROM SNMPv2-SMI RowStatus FROM SNMPv2-TC Unsigned32 FROM SNMPv2-SMI IpAddress FROM SNMPv2-SMI TimeTicks FROM SNMPv2-SMI Counter32 FROM SNMPv2-SMI Counter64 FROM SNMPv2-SMI Integer32 FROM SNMPv2-SMI TruthValue FROM SNMPv2-TC MacAddress FROM SNMPv2-TC DisplayString FROM RFC1213-MIB extremeAgent FROM EXTREME-BASE-MIB ExtremeDeviceId FROM EXTREME-BASE-MIB extremeV2Traps FROM EXTREME-BASE-MIB ClientAuthType FROM EXTREME-BASE-MIB WPACipherSet FROM EXTREME-BASE-MIB WPAKeyMgmtSet FROM EXTREME-BASE-MIB WirelessRemoteConnectBindingType FROM EXTREME-BASE-MIB InetAddressType FROM INET-ADDRESS-MIB InetAddress FROM INET-ADDRESS-MIB extremeAP FROM EXTREME-BASE-MIB extremeLAC FROM EXTREME-BASE-MIB TEXTUAL-CONVENTION FROM SNMPv2-TC; extremeWireless MODULE-IDENTITY LAST-UPDATED "0211230000Z" ORGANIZATION "Extreme Networks, Inc." CONTACT-INFO "www.extremenetworks.com" DESCRIPTION "Extreme Wireless Access Tables" ::= { extremeAgent 25 } extremeAPTraps OBJECT IDENTIFIER ::= { extremeV2Traps 5 } extremeAPTrapsPrefix OBJECT IDENTIFIER ::= { extremeAPTraps 0 } extremeLACGeneral OBJECT IDENTIFIER ::= { extremeLAC 1 } extremeProfile OBJECT IDENTIFIER ::= { extremeLAC 2 } -- *************************************************************** -- -- *************************************************************** -- Dot11Type ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "The current standard supports A, B, G interfaces." SYNTAX INTEGER { a(1), b(2), g(3), bg(4) } Dot11Speed ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "Specifies the speed in Mbps to use for the interface. A value of 0 indicates auto." SYNTAX BITS { speed1(0), speed2(1), speed5(2), speed11(3), speed6(4), speed9(5), speed12(6), speed18(7), speed24(8), speed36(9), speed48(10), speed54(11)} -- Added for DFS support. To be used for listing channels on -- which Radar interference was detected. Dot11AChannel ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "Specifies the channel number for 802.11A interface." SYNTAX BITS { channel36(0), channel40(1), channel44(2), channel52(3), channel56(4), channel60(5), channel64(6), channel100(7), channel104(8), channel108(9), channel112(10), channel116(11), channel120(12), channel124(13), channel128(14), channel132(15), channel140(16) } Dot11AuthMode ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "Specifies the allowed authentication type." SYNTAX INTEGER { open(0), shared(1)} NetworkAuthMode ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "Specifies the allowed authentication type." SYNTAX INTEGER { none(0), webNetlogin(1), macRadius(2), wpaPlusLegacy(3), wpaOnly(4), wpa2PlusWPA(5), wpa2Only(6)} ExtremeWirelessCountryCode ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "Specifies the country code the AP operates in." SYNTAX INTEGER { unitedStates(840), japan(392), taiwan(158), newZealand(554), albania ( 8), algeria ( 12), argentina ( 32), armenia ( 51), australia ( 36), austria ( 40), azerbaijan ( 31), bahrain ( 48), belarus ( 112), belgium ( 56), belize ( 84), bolivia ( 68), brazil ( 76), bruneiDarussalam ( 96), bulgaria ( 100), canada ( 124), chile ( 152), china ( 156), colombia ( 170), costaRica ( 188), croatia ( 191), cyprus ( 196), czech ( 203), denmark ( 208), dominicanRepublic ( 214), ecuador ( 218), egypt ( 818), elSalvador ( 222), estonia ( 233), faeroeIslands ( 234), finland ( 246), france ( 250), georgia ( 268), germany ( 276), greece ( 300), guatemala ( 320), honduras ( 340), hongKong ( 344), hungary ( 348), iceland ( 352), india ( 356), indonesia ( 360), iran ( 364), iraq ( 368), ireland ( 372), israel ( 376), italy ( 380), jamaica ( 388), japan1 ( 393), japan2 ( 394), japan3 ( 395), jordan ( 400), kazakhstan ( 398), kenya ( 404), koreaNorth ( 408), koreaRoc ( 410), koreaRoc2 ( 411), kuwait ( 414), latvia ( 428), lebanon ( 422), libya ( 434), liechtenstein ( 438), lithuania ( 440), luxembourg ( 442), macau ( 446), macedonia ( 807), malaysia ( 458), mexico ( 484), monaco ( 492), morocco ( 504), netherlands ( 528), nicaragua ( 558), norway ( 578), oman ( 512), pakistan ( 586), panama ( 591), paraguay ( 600), peru ( 604), philippines ( 608), poland ( 616), portugal ( 620), puertoRico ( 630), qatar ( 634), romania ( 642), russia ( 643), saudiArabia ( 682), singapore ( 702), slovakia ( 703), slovenia ( 705), southAfrica ( 710), spain ( 724), sweden ( 752), switzerland ( 756), syria ( 760), thailand ( 764), trinidadTYobago ( 780), tunisia ( 788), turkey ( 792), uae ( 784), ukraine ( 804), unitedKingdom ( 826), uruguay ( 858), uzbekistan ( 860), venezuela ( 862), vietNam ( 704), yemen ( 887), zimbabwe ( 716), restOfTheWorld ( 0), extremeDefault ( 998), unknown ( 999) } ExtremeWirelessAntennaType ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "Specifies Antenna type attached to the access-point. The integrated antenna is specified by CTL table on PCI eeprom. The detachable model 15901 is an omni-directional antenna. The detachable model 15902 is a directional antenna." SYNTAX INTEGER { integrated(0), detachable15901(1), detachable15902(2) } ExtremeWirelessAntennaLocation ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "Specifies whether the antenna is an indoor or outdoor antenna" SYNTAX INTEGER { indoor(0), outdoor(1) } ExtremeWirelessPhysInterfaceIndex ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "The value of a physical interface number. Each radio on an AP corresponds to a physical interface. There can be multiple virtual interface on each physical interface. The format for the physical interface is xxxxyy where xxxx is the port IF index to which the AP is connected. YY is the interface index within that AP." SYNTAX Integer32(1..2147483647) ExtremeWirelessVirtInterfaceIndex ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "The value of a virtual interface number. Each radio on an AP corresponds to a physical interface. There can be multiple virtual interface on each physical interface. The format for the virtual interface is xxxxyyzz where xxxx is the port IF index to which the AP is connected. YY is the physical interface index within that AP and ZZ is the index of the virtual interface within that physical interface." SYNTAX Integer32(1..2147483647) ExtremeWirelessChannelAutoSelectStatus ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "Specifies the status of the channel auto-selection process." SYNTAX BITS { notApplicable(0), inProgress(1), success(2), radarInterferenceDuringScan(3), radarInterferenceDuringOperation(4), restartedDueToInterference(5)} -- *************************************************************** -- -- Device wide Properties -- -- *************************************************************** -- extremeAPTotalAuthFailures OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "This variable gives the total number of Authentication failures that have been seen by all the wireless ports." ::= { extremeLACGeneral 1 } extremeAPTotalDetectedStations OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "This variable gives the total number of detected stations on all the wireless ports." ::= { extremeLACGeneral 2 } extremeAPTotalAssociatedStations OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "This variable gives the total number of associated stations on all the wireless ports." ::= { extremeLACGeneral 3 } extremeAPTotalAuthenticatedStations OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "This variable gives the total number of authenticated stations on all the wireless ports." ::= { extremeLACGeneral 4 } extremeWirelessCfgMgmtVLAN OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION "This value indicates the VLAN tag that should be applied to all control traffic between the AP and the platform." ::= { extremeLACGeneral 5 } extremeWirelessCfgNetmask OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-write STATUS current DESCRIPTION "This value is the subnet of the Mgmt Vlan" ::= { extremeLACGeneral 6 } extremeWirelessCfgGateway OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-write STATUS current DESCRIPTION "This value is assigned to the APs as the gateway for the management vlan." ::= { extremeLACGeneral 7 } extremeWirelessCfgEnableWirelessTraps OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "If set to TRUE the wireless port will send traps for Authentication and association events. If set to FALSE no traps will be generated. Note: We always generate the wireless port status traps." ::= { extremeLACGeneral 8 } extremeWirelessCfgCountryCode OBJECT-TYPE SYNTAX ExtremeWirelessCountryCode MAX-ACCESS read-write STATUS current DESCRIPTION "This variable allows configuration of the country code in which the AP will operate. Setting this value will enable the AP to range check frequency and other regulatory settings." ::= { extremeLACGeneral 10 } -- *************************************************************** -- -- Wireless Port Configuration Table -- -- -- -- The configuration table contains one entry for each port on the -- -- device which can host wireless function. Configuration of the -- -- port is done without regard to the presence or absence of an AP -- -- on that port. -- -- -- -- *************************************************************** -- extremeWirelessPortCfgTable OBJECT-TYPE SYNTAX SEQUENCE OF ExtremeWirelessPortCfgEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains one entry per wireless port that the user has configured. The AP does not have to be plugged in for the user to configure it via this table." ::= { extremeLAC 3 } extremeWirelessPortCfgEntry OBJECT-TYPE SYNTAX ExtremeWirelessPortCfgEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "" INDEX { extremeWirelessPortIfIndex } ::= { extremeWirelessPortCfgTable 1 } ExtremeWirelessPortCfgEntry ::= SEQUENCE { extremeWirelessPortIfIndex InterfaceIndex, extremeWirelessPortCfgIpAddress IpAddress, extremeWirelessPortCfgLocation DisplayString, extremeWirelessPortCfgDetectedTimeout TimeTicks, extremeWirelessPortCfgClientWatchdog TruthValue, extremeWirelessPortLastChange TimeTicks, extremeWirelessPortState INTEGER, extremeWirelessPortAntennaType ExtremeWirelessAntennaType, extremeWirelessPortAntennaLocation ExtremeWirelessAntennaLocation } extremeWirelessPortIfIndex OBJECT-TYPE SYNTAX InterfaceIndex MAX-ACCESS read-only STATUS current DESCRIPTION "This is the MIB-II ifIndex of the port this entry describes." ::= { extremeWirelessPortCfgEntry 1 } extremeWirelessPortCfgIpAddress OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-write STATUS current DESCRIPTION "This value is assigned to the port for external management." ::= { extremeWirelessPortCfgEntry 2 } extremeWirelessPortCfgLocation OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-write STATUS current DESCRIPTION "This describes the physical location of the wireless port." ::= { extremeWirelessPortCfgEntry 3 } extremeWirelessPortCfgDetectedTimeout OBJECT-TYPE SYNTAX TimeTicks MAX-ACCESS read-write STATUS current DESCRIPTION "This is the number of seconds a station can stay in the detected station table without authenticating." ::= { extremeWirelessPortCfgEntry 4 } extremeWirelessPortCfgClientWatchdog OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "Setting this value to true will force the AP to run a watch-dog process for system health." ::= { extremeWirelessPortCfgEntry 5 } extremeWirelessPortLastChange OBJECT-TYPE SYNTAX TimeTicks MAX-ACCESS read-only STATUS current DESCRIPTION "The value of sysUpTime when the port entered its last state" ::= { extremeWirelessPortCfgEntry 6 } extremeWirelessPortState OBJECT-TYPE SYNTAX INTEGER { disabled(1), enabled(2), reset(3), addressing(4), register(5), syncing(6), online(7), error(8) } MAX-ACCESS read-only STATUS current DESCRIPTION "The current state of the wireless part of this port. enabled : Port is actively looking for wireless interfaces. disabled : Port is administratively unable to detect new interfaces. reset : Interfaces have been detected and are being brought up (access point is booting). addressing : IP Address is being assigned. register : Interfaces are registering for service syncing : Interfaces are retrieving their configuration and updating their state. online : Interfaces are operational. If an error occurs the wireless port will transistion to the error state." ::= { extremeWirelessPortCfgEntry 7 } -- TODO: What is the meaning of this variable? extremeWirelessPortAntennaType OBJECT-TYPE SYNTAX ExtremeWirelessAntennaType MAX-ACCESS read-write STATUS current DESCRIPTION "This is the type of the Antenna for Detachable product. For Altitude-2d series, further selection is available through this variable." ::= { extremeWirelessPortCfgEntry 8 } extremeWirelessPortAntennaLocation OBJECT-TYPE SYNTAX ExtremeWirelessAntennaLocation MAX-ACCESS read-write STATUS current DESCRIPTION "This specifies the location the detachable antenna." ::= { extremeWirelessPortCfgEntry 9 } -- *************************************************************** -- -- Wireless Port Status Table -- -- -- -- Status table has one entry for every attached AP. Each entry -- -- contains a duplicate of the values which are configured in the -- -- configuration table, as well as status and other information -- -- learned from the device. -- -- *************************************************************** -- extremeWirelessPortStatusTable OBJECT-TYPE SYNTAX SEQUENCE OF ExtremeWirelessPortStatusEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains one entry per detected AP." ::= { extremeAP 1 } extremeWirelessPortStatusEntry OBJECT-TYPE SYNTAX ExtremeWirelessPortStatusEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "" INDEX { extremeWirelessPortIfIndex } ::= { extremeWirelessPortStatusTable 1 } ExtremeWirelessPortStatusEntry ::= SEQUENCE { extremeWirelessPortIpAddress IpAddress, extremeWirelessPortNetmask IpAddress, extremeWirelessPortGateway IpAddress, extremeWirelessPortManagementIP IpAddress, extremeWirelessPortEnableWirelessTraps TruthValue, extremeWirelessPortLocation DisplayString, extremeWirelessPortDetectedMaxAge TimeTicks, extremeWirelessPortMgmtVLAN INTEGER, extremeWirelessPortBootromVersion DisplayString, extremeWirelessPortSWVersion DisplayString, extremeWirelessPortSysDescr DisplayString, extremeWirelessPortManufacturerName DisplayString, extremeWirelessPortProductName DisplayString, extremeWirelessPortSerialNumber DisplayString, extremeWirelessPortEdpNeighborId ExtremeDeviceId, extremeWirelessPortClearCounters TruthValue, extremeWirelessPortClearLog TruthValue, extremeWirelessPortWatchdogReset TruthValue, extremeWirelessPortNumPhysInterfaces INTEGER, extremeWirelessPortHWVersion DisplayString, extremeWirelessPortMacAddress MacAddress, extremeWirelessPortRadiusPortID DisplayString, extremeWirelessPortBootUpTime TimeTicks, extremeWirelessPortCountryCode ExtremeWirelessCountryCode, extremeWirelessPortWallclockTime INTEGER, extremeWirelessPortPartNumber DisplayString, extremeWirelessPortPartRevision DisplayString, extremeWirelessPortUpTime TimeTicks, extremeWirelessPortStatusAntennaType ExtremeWirelessAntennaType, extremeWirelessPortStatusAntennaLocation ExtremeWirelessAntennaLocation, extremeWirelessPortStatusAntenna2point4GHZGain INTEGER, extremeWirelessPortStatusAntenna5GHZGain INTEGER, extremeWirelessPortPrimaryBootloaderVersion DisplayString, extremeWirelessPortSecondaryBootloaderVersion DisplayString, extremeWirelessPortCurrentBootloaderInUse INTEGER } extremeWirelessPortIpAddress OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-write STATUS current DESCRIPTION "This value is assigned to the port for external management." ::= { extremeWirelessPortStatusEntry 1 } extremeWirelessPortNetmask OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-write STATUS current DESCRIPTION "This value is assigned to the AP for external management." ::= { extremeWirelessPortStatusEntry 2 } extremeWirelessPortGateway OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-write STATUS current DESCRIPTION "This value is assigned to the AP for external management." ::= { extremeWirelessPortStatusEntry 3 } extremeWirelessPortManagementIP OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-write STATUS current DESCRIPTION "This value is used by the AP when sending out Management packets to the external world. This IP is used as src-ip address in Syslog messages, as NAS-Identifier in Radius requests, and as Agent-Addr in SNMP trap pdu's." ::= { extremeWirelessPortStatusEntry 4 } extremeWirelessPortEnableWirelessTraps OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "If set to TRUE the wireless port will send traps for Authentication and association successful events. If set to FALSE no traps will be generated. Note: We always generate the wireless port status traps." ::= { extremeWirelessPortStatusEntry 5 } extremeWirelessPortLocation OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-write STATUS current DESCRIPTION "This describes the physical location of the wireless port." ::= { extremeWirelessPortStatusEntry 6 } extremeWirelessPortDetectedMaxAge OBJECT-TYPE SYNTAX TimeTicks MAX-ACCESS read-write STATUS current DESCRIPTION "This is the number of seconds a station can stay in the detected station table without authenticating." ::= { extremeWirelessPortStatusEntry 7 } extremeWirelessPortMgmtVLAN OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "This value indicates the VLAN tag that should be applied to all control traffic between the AP and the platform." ::= { extremeWirelessPortStatusEntry 8 } extremeWirelessPortBootromVersion OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "This is the current version of the bootrom on this AP." ::= { extremeWirelessPortStatusEntry 9 } extremeWirelessPortSWVersion OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "This is the current software version of this AP." ::= { extremeWirelessPortStatusEntry 10 } extremeWirelessPortSysDescr OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "This is the equivalent value of sysDescr from the AP." ::= { extremeWirelessPortStatusEntry 11 } extremeWirelessPortManufacturerName OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION " " REFERENCE "dot11ManufacturerName" ::= { extremeWirelessPortStatusEntry 12 } extremeWirelessPortProductName OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION " " REFERENCE "dot11ProductName" ::= { extremeWirelessPortStatusEntry 13 } extremeWirelessPortSerialNumber OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "This is the unique serial number for this device." ::= { extremeWirelessPortStatusEntry 14 } extremeWirelessPortEdpNeighborId OBJECT-TYPE SYNTAX ExtremeDeviceId MAX-ACCESS read-only STATUS current DESCRIPTION "EDP assigns a unique ID to each neighbor to disambiguate references. This can be used to index into the extremeEdpTable." ::= { extremeWirelessPortStatusEntry 15 } extremeWirelessPortClearCounters OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "This value can be set to true to force the device to reset it's counters. A read will return false." ::= { extremeWirelessPortStatusEntry 16 } extremeWirelessPortClearLog OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "This value can be set to true to force the device to clear its local log store. A read will return false." ::= { extremeWirelessPortStatusEntry 17 } extremeWirelessPortWatchdogReset OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "This is to enable/disable watchdog timer reset on timeout. Default is enable. If it is enabled, system should reset when the watchdog kicks in. On next bootup, it should send out an syslog message to syslog server. If it is disabled, it should record the error and not reset the system." ::= { extremeWirelessPortStatusEntry 18 } extremeWirelessPortNumPhysInterfaces OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "Each wireless port has a set of physical interface which are numbered 1-N. This variable gives the number of physical interfaces on this AP." ::= { extremeWirelessPortStatusEntry 19 } extremeWirelessPortHWVersion OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "This is the current hardware version of this AP." ::= { extremeWirelessPortStatusEntry 20 } extremeWirelessPortMacAddress OBJECT-TYPE SYNTAX MacAddress MAX-ACCESS read-only STATUS current DESCRIPTION "Unique MAC Address assigned to the ethernet interface on the AP." ::= { extremeWirelessPortStatusEntry 21 } extremeWirelessPortRadiusPortID OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-write STATUS current DESCRIPTION "A string value that should be sent by the AP to the radius server as the Port-ID radius attribute in authentication requests" ::= { extremeWirelessPortStatusEntry 22 } extremeWirelessPortBootUpTime OBJECT-TYPE SYNTAX TimeTicks MAX-ACCESS read-write STATUS current DESCRIPTION "The sysUpTime of the LAC when the port was booted up. Should be set only during the AP boot up." ::= { extremeWirelessPortStatusEntry 23 } extremeWirelessPortCountryCode OBJECT-TYPE SYNTAX ExtremeWirelessCountryCode MAX-ACCESS read-write STATUS current DESCRIPTION "The country code that the AP is programmed to operate in." ::= { extremeWirelessPortStatusEntry 24 } extremeWirelessPortWallclockTime OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION "The wall clock time as known to the LAC. Expressed in number of seconds since Jan 1, 1970" ::= { extremeWirelessPortStatusEntry 25 } extremeWirelessPortPartNumber OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-write STATUS current DESCRIPTION "This describes the part number of the AP." ::= { extremeWirelessPortStatusEntry 26 } extremeWirelessPortPartRevision OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-write STATUS current DESCRIPTION "This describes the revision of the AP." ::= { extremeWirelessPortStatusEntry 27 } extremeWirelessPortUpTime OBJECT-TYPE SYNTAX TimeTicks MAX-ACCESS read-write STATUS current DESCRIPTION "The number of seconds the port has been in the online state." ::= { extremeWirelessPortStatusEntry 28 } extremeWirelessPortStatusAntennaType OBJECT-TYPE SYNTAX ExtremeWirelessAntennaType MAX-ACCESS read-write STATUS current DESCRIPTION "This is the type of the Antenna for Detachable product. For Altitude-2d series, further selection is available through this variable." ::= { extremeWirelessPortStatusEntry 29 } extremeWirelessPortStatusAntennaLocation OBJECT-TYPE SYNTAX ExtremeWirelessAntennaLocation MAX-ACCESS read-write STATUS current DESCRIPTION "This specifies the location the detachable antenna." ::= { extremeWirelessPortStatusEntry 30 } extremeWirelessPortStatusAntenna2point4GHZGain OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-create STATUS current DESCRIPTION "This specifies 2.4GHz gain value for detachable antenna in dbi" ::= { extremeWirelessPortStatusEntry 31 } extremeWirelessPortStatusAntenna5GHZGain OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-create STATUS current DESCRIPTION "This specifies 5GHz gain value for detachable antenna in dbi" ::= { extremeWirelessPortStatusEntry 32 } extremeWirelessPortPrimaryBootloaderVersion OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "This is the version of the primary bootloader on this AP." ::= { extremeWirelessPortStatusEntry 33 } extremeWirelessPortSecondaryBootloaderVersion OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "This is the version of the Secondary bootloader on this AP." ::= { extremeWirelessPortStatusEntry 34 } extremeWirelessPortCurrentBootloaderInUse OBJECT-TYPE SYNTAX INTEGER { primary(1), secondary(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "This specifies if the bootloader booted is primary or secondary one." ::= { extremeWirelessPortStatusEntry 35 } -- *************************************************************** -- -- Wireless Port Syslog Status Table -- -- *************************************************************** -- extremeWirelessPortLogStatusTable OBJECT-TYPE SYNTAX SEQUENCE OF ExtremeWirelessPortLogStatusEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains one entry for each wireless port which is configured via the configuration table." ::= { extremeAP 2 } extremeWirelessPortLogStatusEntry OBJECT-TYPE SYNTAX ExtremeWirelessPortLogStatusEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "" INDEX { extremeWirelessPortIfIndex, extremeWirelessPortLogStatusIndex } ::= { extremeWirelessPortLogStatusTable 1 } ExtremeWirelessPortLogStatusEntry ::= SEQUENCE { extremeWirelessPortLogStatusIndex INTEGER, extremeWirelessPortLogStatusDestIp InetAddress, extremeWirelessPortLogStatusDestIpType InetAddressType, extremeWirelessPortLogStatusPort INTEGER, extremeWirelessPortLogStatusFacility INTEGER, extremeWirelessPortLogStatusSeverity INTEGER, extremeWirelessPortLogStatusStatus TruthValue } extremeWirelessPortLogStatusIndex OBJECT-TYPE SYNTAX INTEGER(1..9) MAX-ACCESS not-accessible STATUS current DESCRIPTION "There are 9 entries in this table to correspond to the 8 entries configured in the cfg table plus one for the LAC." ::= { extremeWirelessPortLogStatusEntry 1 } extremeWirelessPortLogStatusDestIp OBJECT-TYPE SYNTAX InetAddress MAX-ACCESS read-write STATUS current DESCRIPTION "This is the IP address to which syslog messsages will be sent. A value of 0.0.0.0 indicates that this entry is disabled. The source IP for every syslog message comes from the ManagementIP field in extremeWirelessPortStatusTable" ::= { extremeWirelessPortLogStatusEntry 2 } extremeWirelessPortLogStatusDestIpType OBJECT-TYPE SYNTAX InetAddressType MAX-ACCESS read-write STATUS current DESCRIPTION "The type of address specified in the object 'extremeWirelessPortLogStatusDestIp. Currently, only 'ipv4' and 'dns' are supported." DEFVAL { ipv4 } ::= { extremeWirelessPortLogStatusEntry 3 } extremeWirelessPortLogStatusPort OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION "This is the port to which syslog messages will be sent." ::= { extremeWirelessPortLogStatusEntry 4 } extremeWirelessPortLogStatusFacility OBJECT-TYPE SYNTAX INTEGER(0..7) MAX-ACCESS read-write STATUS current DESCRIPTION "Optional value for syslog facility local0-7." ::= { extremeWirelessPortLogStatusEntry 5 } extremeWirelessPortLogStatusSeverity OBJECT-TYPE SYNTAX INTEGER { critical (0), error (1), warning (2), notice (3), info (4), debugSummary (5), debugVerbose (6), debugData (7) } MAX-ACCESS read-write STATUS current DESCRIPTION "The syslog message severity. All syslog messages that have a severity >= specified severity, will be sent to this syslog server." DEFVAL { debugData } ::= { extremeWirelessPortLogStatusEntry 6 } extremeWirelessPortLogStatusStatus OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "Specifies whether the log server is enabled or not." ::= { extremeWirelessPortLogStatusEntry 7 } -- *************************************************************** -- -- Wireless Port Log Table -- -- *************************************************************** -- extremeWirelessPortLogTable OBJECT-TYPE SYNTAX SEQUENCE OF ExtremeWirelessPortLogEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table allows access to the syslog entries on particular wireless ports." ::= { extremeAP 3 } extremeWirelessPortLogEntry OBJECT-TYPE SYNTAX ExtremeWirelessPortLogEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "" INDEX { extremeWirelessPortIfIndex, extremeWirelessPortLogIndex } ::= { extremeWirelessPortLogTable 1 } ExtremeWirelessPortLogEntry ::= SEQUENCE { extremeWirelessPortLogIndex INTEGER, extremeWirelessPortLogMessage DisplayString } extremeWirelessPortLogIndex OBJECT-TYPE SYNTAX INTEGER(0..65535) MAX-ACCESS not-accessible STATUS current DESCRIPTION "This is an arbitrary integer which is assinged to entries in order of their insertion." ::= { extremeWirelessPortLogEntry 1 } extremeWirelessPortLogMessage OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "This is the formatted syslog message which was sent." ::= { extremeWirelessPortLogEntry 2 } -- *************************************************************** -- -- Wireless Physical Interface Ctl Table -- -- This table allows for the configuration of parameters that deal -- -- with physical interfaces. Each radio on the AP is represented by-- -- a physical interface. Each physical interface can have multiple -- -- (upto 8) virtual interfaces. RF properties are configured on the-- -- physical interface using the extremeWirelessInterfaceRFCtlTable -- -- Security parameters are configured on the virtual interface -- -- using the extremeWirelessInterfaceSecurityCtlTable -- -- *************************************************************** -- extremeWirelessPhysInterfaceCtlTable OBJECT-TYPE SYNTAX SEQUENCE OF ExtremeWirelessPhysInterfaceCtlEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table provides configuration of per-physical interface values." ::= { extremeAP 4 } ExtremeWirelessPhysInterfaceCtlEntry ::= SEQUENCE { extremeWirelessPhysInterfaceIndex ExtremeWirelessPhysInterfaceIndex, extremeWirelessPhysInterfacePHYChannel INTEGER, extremeWirelessPhysInterfaceSpeed Dot11Speed, extremeWirelessPhysInterfaceNumVirtInterfaces INTEGER, extremeWirelessPhysInterfaceChannelAutoSelectStatus ExtremeWirelessChannelAutoSelectStatus, extremeWirelessPhysInterfaceRadarInterfaceChannelList Dot11AChannel } extremeWirelessPhysInterfaceCtlEntry OBJECT-TYPE SYNTAX ExtremeWirelessPhysInterfaceCtlEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Each entry is indexed by the wirelessInterfaceIndex, and represents a wireless interface." INDEX { extremeWirelessPhysInterfaceIndex } ::= { extremeWirelessPhysInterfaceCtlTable 1 } extremeWirelessPhysInterfaceIndex OBJECT-TYPE SYNTAX ExtremeWirelessPhysInterfaceIndex MAX-ACCESS accessible-for-notify STATUS current DESCRIPTION "This is the ifIndex of an individual physical interface on an AP. Each radio will have a unique value." ::= { extremeWirelessPhysInterfaceCtlEntry 1 } extremeWirelessPhysInterfacePHYChannel OBJECT-TYPE SYNTAX INTEGER (0..99) MAX-ACCESS read-write STATUS current DESCRIPTION "This is the RF channel which will be used by this transmitter. Range should be established by configuration of RegDomain and PHYType." ::= { extremeWirelessPhysInterfaceCtlEntry 2 } extremeWirelessPhysInterfaceSpeed OBJECT-TYPE SYNTAX Dot11Speed MAX-ACCESS read-write STATUS current DESCRIPTION "This value indicates the current setting for Tx speed for the interface. Only one of thebits of this bit set can be set. If all bits are unset (ie a 0 is passed as a value) then it means that the interface should choose a speed based on some algorithm." ::= { extremeWirelessPhysInterfaceCtlEntry 3 } extremeWirelessPhysInterfaceNumVirtInterfaces OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION "Each physical interface has a number of virtual interfaces This specifies the number of virt interfaces." ::= { extremeWirelessPhysInterfaceCtlEntry 4 } -- Added for DFS extremeWirelessPhysInterfaceChannelAutoSelectStatus OBJECT-TYPE SYNTAX ExtremeWirelessChannelAutoSelectStatus MAX-ACCESS read-only STATUS current DESCRIPTION "This OID reflects the status of the channel auto selection process." ::= { extremeWirelessPhysInterfaceCtlEntry 5 } -- Added for DFS extremeWirelessPhysInterfaceRadarInterfaceChannelList OBJECT-TYPE SYNTAX Dot11AChannel MAX-ACCESS read-only STATUS current DESCRIPTION "This OID reflects the list oc 802.11(a) channels on which radar interference was detected." ::= { extremeWirelessPhysInterfaceCtlEntry 6 } -- *************************************************************** -- -- Wireless Virtual Interface Ctl Table -- -- This table allows for the configuration of parameters that deal -- -- with virtual interfaces. Each radio on the AP is represented by-- -- a physical interface. Each physical interface can have multiple -- -- (upto 8) virtual interfaces. RF properties are configured on the-- -- physical interface using the extremeWirelessInterfaceRFCtlTable -- -- Security parameters are configured on the virtual interface -- -- using the extremeWirelessInterfaceSecurityCtlTable -- -- *************************************************************** -- extremeWirelessVirtInterfaceCtlTable OBJECT-TYPE SYNTAX SEQUENCE OF ExtremeWirelessVirtInterfaceCtlEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table provides configuration of per-physical-interface values." ::= { extremeAP 6 } ExtremeWirelessVirtInterfaceCtlEntry ::= SEQUENCE { extremeWirelessVirtInterfaceIndex ExtremeWirelessVirtInterfaceIndex, extremeWirelessVirtInterfaceMacAddress MacAddress, extremeWirelessVirtInterfaceMaxClients INTEGER, extremeWirelessVirtInterfaceWirelessBridging TruthValue, extremeWirelessVirtInterfaceLastStateChange TimeTicks, extremeWirelessVirtInterfaceState INTEGER, extremeWirelessVirtInterfaceIappEnabled TruthValue, extremeWirelessVirtInterfaceSvpEnabled TruthValue } extremeWirelessVirtInterfaceCtlEntry OBJECT-TYPE SYNTAX ExtremeWirelessVirtInterfaceCtlEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Each entry is indexed by the wirelessInterfaceIndex, and represents a virtual wireless interface." INDEX { extremeWirelessVirtInterfaceIndex } ::= { extremeWirelessVirtInterfaceCtlTable 1 } extremeWirelessVirtInterfaceIndex OBJECT-TYPE SYNTAX ExtremeWirelessVirtInterfaceIndex MAX-ACCESS accessible-for-notify STATUS current DESCRIPTION "This is the ifIndex of an individual interface on an AP. Each virtual interface will have a unique value." ::= { extremeWirelessVirtInterfaceCtlEntry 1 } extremeWirelessVirtInterfaceMacAddress OBJECT-TYPE SYNTAX MacAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The maximum number of clients that can associate with this virtual interface." ::= { extremeWirelessVirtInterfaceCtlEntry 2 } extremeWirelessVirtInterfaceMaxClients OBJECT-TYPE SYNTAX INTEGER (1..128) MAX-ACCESS read-write STATUS current DESCRIPTION "The maximum number of clients that can associate with this virtual interface." ::= { extremeWirelessVirtInterfaceCtlEntry 3 } extremeWirelessVirtInterfaceWirelessBridging OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "This specifies whether wireless bridging is enabled on this interface. If wireless bridging is enabled then traffic originating from a client on this interface will be bridged to clients on the same VLAN on this or other virtual interfaces that have wireless bridging enabled. So basically wireless bridging should be enabled on both the source and the destination virtual interface for traffic to be bridged." ::= { extremeWirelessVirtInterfaceCtlEntry 4 } extremeWirelessVirtInterfaceLastStateChange OBJECT-TYPE SYNTAX TimeTicks MAX-ACCESS read-only STATUS current DESCRIPTION "The value of sysUpTime when the virtual interface entered its current state" ::= { extremeWirelessVirtInterfaceCtlEntry 5 } extremeWirelessVirtInterfaceState OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "This value specifies whether the virtual interface is active or not" ::= { extremeWirelessVirtInterfaceCtlEntry 6 } extremeWirelessVirtInterfaceIappEnabled OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "IAPP status. A value of TRUE indicates IAPP is enabled on the interface." ::= { extremeWirelessVirtInterfaceCtlEntry 7 } extremeWirelessVirtInterfaceSvpEnabled OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "SVP status. A value of TRUE indicates SVP is enabled on the interface." ::= { extremeWirelessVirtInterfaceCtlEntry 8 } -- *************************************************************** -- -- Wireless Interface Security Ctl Table -- -- This table allows for the configuration of per-wireless-intf -- -- security parameters. Each Wireless interface is represented in -- -- ifTable, and is represented by extremeWirelessInterfaceIfIndex. -- -- *************************************************************** -- extremeWirelessVirtInterfaceSecurityCtlTable OBJECT-TYPE SYNTAX SEQUENCE OF ExtremeWirelessVirtInterfaceSecurityCtlEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table provides configuration of per-interface values." ::= { extremeAP 7 } extremeWirelessVirtInterfaceSecurityCtlEntry OBJECT-TYPE SYNTAX ExtremeWirelessVirtInterfaceSecurityCtlEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Each entry is indexed by the wirelessInterfaceIndex, and represents a wireless interface." INDEX { extremeWirelessVirtInterfaceIndex } ::= { extremeWirelessVirtInterfaceSecurityCtlTable 1 } ExtremeWirelessVirtInterfaceSecurityCtlEntry ::= SEQUENCE { extremeWirelessVirtInterfaceESSName OCTET STRING, extremeWirelessVirtInterfaceSSIDInBeacon TruthValue, extremeWirelessVirtInterfaceDot11AuthMode Dot11AuthMode, extremeWirelessVirtInterfaceNetworkAuthMode NetworkAuthMode, extremeWirelessVirtInterfaceDataVlan INTEGER, extremeWirelessVirtInterfaceIgnoreVSAVlan TruthValue, extremeWirelessVirtInterfaceWEPDefaultKey INTEGER, extremeWirelessVirtInterfaceEncryptionLength INTEGER } extremeWirelessVirtInterfaceESSName OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-write STATUS current DESCRIPTION "The ESS ID of this interface." ::= { extremeWirelessVirtInterfaceSecurityCtlEntry 1 } extremeWirelessVirtInterfaceSSIDInBeacon OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "Does this interface generate a beacon with the SSID in it?" ::= { extremeWirelessVirtInterfaceSecurityCtlEntry 2 } extremeWirelessVirtInterfaceDot11AuthMode OBJECT-TYPE SYNTAX Dot11AuthMode MAX-ACCESS read-write STATUS current DESCRIPTION "Setting this to true indicates whether to use open or shared authentication" ::= { extremeWirelessVirtInterfaceSecurityCtlEntry 3 } extremeWirelessVirtInterfaceNetworkAuthMode OBJECT-TYPE SYNTAX NetworkAuthMode MAX-ACCESS read-write STATUS current DESCRIPTION "This specifies the authentication mode to use on top of dot11 MAC authentication" ::= { extremeWirelessVirtInterfaceSecurityCtlEntry 4 } extremeWirelessVirtInterfaceDataVlan OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION "This is the VLAN to use for client data in case of the VLAN is not received as a VSA. This VLAN is also used for authentication types like PSK, WEP, etc" ::= { extremeWirelessVirtInterfaceSecurityCtlEntry 5 } extremeWirelessVirtInterfaceIgnoreVSAVlan OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "If this is set then the VLAN returned as a VSA will be ignored and the Data Vlan specified above will be used instead" ::= { extremeWirelessVirtInterfaceSecurityCtlEntry 6 } extremeWirelessVirtInterfaceWEPDefaultKey OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION "This value indicates the index in dot11WEPDefaultKeyTable that identifies the key this interface will use to decrypt packets." ::= { extremeWirelessVirtInterfaceSecurityCtlEntry 7 } extremeWirelessVirtInterfaceEncryptionLength OBJECT-TYPE SYNTAX INTEGER { none(0), sixtyfour(64), onetwentyeight(128) } MAX-ACCESS read-write STATUS current DESCRIPTION "This is the length of the encryption key to use in case of dot1x legacy mode and WEP. If this length is 0 then no WEP encryption." ::= { extremeWirelessVirtInterfaceSecurityCtlEntry 8 } -- *************************************************************** -- -- Wireless Interface Dot1x Ctl Table -- -- This table allows for the configuration of per-wireless-intf -- -- dot1x parameters. Each Wireless interface is represented in -- -- ifTable, and is represented by extremeWirelessVirtInterfaceIfIndex. -- -- *************************************************************** -- extremeWirelessVirtInterfaceDot1xCtlTable OBJECT-TYPE SYNTAX SEQUENCE OF ExtremeWirelessVirtInterfaceDot1xCtlEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "There is one entry in this table for each virtual interface It reflects the dot1x security config" ::= { extremeAP 8 } extremeWirelessVirtInterfaceDot1xCtlEntry OBJECT-TYPE SYNTAX ExtremeWirelessVirtInterfaceDot1xCtlEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "" INDEX { extremeWirelessVirtInterfaceIndex } ::= { extremeWirelessVirtInterfaceDot1xCtlTable 1 } ExtremeWirelessVirtInterfaceDot1xCtlEntry ::= SEQUENCE { extremeWirelessVirtInterfaceKeyMgmtSuite WPAKeyMgmtSet, extremeWirelessVirtInterfaceMcastCipherSuite WPACipherSet, extremeWirelessVirtInterfaceDot1xPSKValue OCTET STRING, extremeWirelessVirtInterfaceDot1xPSKPassPhrase DisplayString, extremeWirelessVirtInterfaceDot1xReAuthPeriod INTEGER, extremeWirelessVirtInterfaceGroupUpdateTimeOut Unsigned32, extremeWirelessVirtInterfacePairwiseUpdateTimeOut Unsigned32, extremeWirelessVirtInterfaceDot11iPreauthEnable TruthValue } extremeWirelessVirtInterfaceKeyMgmtSuite OBJECT-TYPE SYNTAX WPAKeyMgmtSet MAX-ACCESS read-write STATUS current DESCRIPTION "This bitmask configures the authentication suites to be used." ::= { extremeWirelessVirtInterfaceDot1xCtlEntry 1 } extremeWirelessVirtInterfaceMcastCipherSuite OBJECT-TYPE SYNTAX WPACipherSet MAX-ACCESS read-write STATUS current DESCRIPTION "This configures the cipher suite to use for mcast traffic. The cipher suite to use for unicast traffic is derived from this using the following algorithm: Mcast cipher = WEP (64/128), Unicast cipher = TKIP Mcast cipher = TKIP, Unicast cipher = TKIP Mcast cipher = AES, Unicast cipher = AES. This therefore determines the max unicast cipher suite the client can use to associate with this interface." ::= { extremeWirelessVirtInterfaceDot1xCtlEntry 2 } extremeWirelessVirtInterfaceDot1xPSKValue OBJECT-TYPE SYNTAX OCTET STRING (SIZE(32)) MAX-ACCESS read-write STATUS current DESCRIPTION "The Pre-Shared Key (PSK) for when WPA in PSK mode is the selected authentication suite." REFERENCE "dot11RSNConfigPSKValue" ::= { extremeWirelessVirtInterfaceDot1xCtlEntry 3 } extremeWirelessVirtInterfaceDot1xPSKPassPhrase OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-write STATUS current DESCRIPTION "The PSK, for when WPA in PSK mode is the selected authentication suite, is configured by extremeWirelessVirtInterfaceKeyMgmtSuite. An alternative manner of setting the PSK uses the password-to-key algorithm defined in section XXX. This variable provides a means to enter a pass phrase. When this object is written, the RSN entity shall use the password-to-key algorithm specified in section XXX to derive a pre-shared and populate extremeWirelessVirtInerfaceDot1xPSKValue with this key. This object is logically write-only. Reading this variable shall return unsuccessful status or null or zero." ::= { extremeWirelessVirtInterfaceDot1xCtlEntry 4 } extremeWirelessVirtInterfaceDot1xReAuthPeriod OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION "Number of seconds a clients authentication will last before the AP automatically issues a reauthentication request." ::= { extremeWirelessVirtInterfaceDot1xCtlEntry 5 } extremeWirelessVirtInterfaceGroupUpdateTimeOut OBJECT-TYPE SYNTAX Unsigned32 (1..1440) UNITS "minutes" MAX-ACCESS read-write STATUS current DESCRIPTION "The time in minutes after which the RSN group update handshake will be retried. The timer shall start at the moment the group update message is sent." REFERENCE "dot11RSNConfigGroupUpdateTimeOut" DEFVAL { 100 } -- ::= { extremeWirelessVirtInterfaceDot1xCtlEntry 6 } extremeWirelessVirtInterfacePairwiseUpdateTimeOut OBJECT-TYPE SYNTAX Unsigned32 (1..1440) UNITS "minutes" MAX-ACCESS read-write STATUS current DESCRIPTION "The time in minutes after which the RSN 4-way handshake will be retried. The timer shall start at the moment a 4-way message is sent." REFERENCE "dot11RSNConfigPairwiseUpdateTimeOut" DEFVAL { 100 } -- ::= { extremeWirelessVirtInterfaceDot1xCtlEntry 7 } extremeWirelessVirtInterfaceDot11iPreauthEnable OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "Enables/Disable 802.11i pre-authentication." ::= { extremeWirelessVirtInterfaceDot1xCtlEntry 8 } -- *************************************************************** -- -- Default WEP Key Table -- -- *************************************************************** -- extremeWirelessVirtInterfaceWEPKeyTable OBJECT-TYPE SYNTAX SEQUENCE OF ExtremeWirelessVirtInterfaceWEPKeyEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains per-profile WEP keys. Reference ieee802dot11.1.2.3." ::= { extremeAP 9 } extremeWirelessVirtInterfaceWEPKeyEntry OBJECT-TYPE SYNTAX ExtremeWirelessVirtInterfaceWEPKeyEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION " " INDEX { extremeWirelessVirtInterfaceIndex, extremeWirelessVirtInterfaceWEPKeyIndex } ::= { extremeWirelessVirtInterfaceWEPKeyTable 1 } ExtremeWirelessVirtInterfaceWEPKeyEntry ::= SEQUENCE { extremeWirelessVirtInterfaceWEPKeyIndex INTEGER, extremeWirelessVirtInterfaceWEPKey OCTET STRING, extremeWirelessVirtInterfaceWEPKeyStatus TruthValue } extremeWirelessVirtInterfaceWEPKeyIndex OBJECT-TYPE SYNTAX INTEGER(1..4) MAX-ACCESS not-accessible STATUS current DESCRIPTION "There can be upto 4 wep keys for any wireless interface. Four of the keys are to be used with WEP Authentication, and the other four with MAC Auth." ::= { extremeWirelessVirtInterfaceWEPKeyEntry 1 } extremeWirelessVirtInterfaceWEPKey OBJECT-TYPE SYNTAX OCTET STRING (SIZE(1..19)) MAX-ACCESS read-create STATUS current DESCRIPTION "This is a write-only wep key." ::= { extremeWirelessVirtInterfaceWEPKeyEntry 2 } extremeWirelessVirtInterfaceWEPKeyStatus OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-create STATUS current DESCRIPTION "Specifies whether the key is present or not." ::= { extremeWirelessVirtInterfaceWEPKeyEntry 3 } -- *************************************************************** -- -- Wireless Interface RF Ctl Table -- -- This table allows for the configuration of per-wireless-intf -- -- RF parameters. Each Wireless interface is represented in -- -- ifTable, and is represented by extremeWirelessPhysInterfaceIfIndex. -- -- *************************************************************** -- extremeWirelessPhysInterfaceRFCtlTable OBJECT-TYPE SYNTAX SEQUENCE OF ExtremeWirelessPhysInterfaceRFCtlEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table provides configuration of per-interface values." ::= { extremeAP 10 } extremeWirelessPhysInterfaceRFCtlEntry OBJECT-TYPE SYNTAX ExtremeWirelessPhysInterfaceRFCtlEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Each entry is indexed by the wirelessInterfaceIndex, and represents a wireless interface." INDEX { extremeWirelessPhysInterfaceIndex } ::= { extremeWirelessPhysInterfaceRFCtlTable 1 } ExtremeWirelessPhysInterfaceRFCtlEntry ::= SEQUENCE { extremeWirelessPhysInterfaceBeaconPeriod INTEGER, extremeWirelessPhysInterfaceTxPowerLevel INTEGER, extremeWirelessPhysInterfaceDTIMPeriod INTEGER, extremeWirelessPhysInterfaceFragLength INTEGER, extremeWirelessPhysInterfaceLongRetry INTEGER, extremeWirelessPhysInterfaceShortRetry INTEGER, extremeWirelessPhysInterfaceRTSThreshold INTEGER, extremeWirelessPhysInterfaceSupportedDataRatesRxValue Dot11Speed, extremeWirelessPhysInterfaceSupportedDataRatesTxValue Dot11Speed, extremeWirelessPhysInterfacePHYType Dot11Type, extremeWirelessPhysInterfacePHYSupportedTypes BITS, extremeWirelessPhysInterfacePreamble INTEGER, extremeWirelessPhysInterfaceAbsTxPowerLevel INTEGER } extremeWirelessPhysInterfaceBeaconPeriod OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION "This is the beacon interval to use" ::= { extremeWirelessPhysInterfaceRFCtlEntry 1 } extremeWirelessPhysInterfaceTxPowerLevel OBJECT-TYPE SYNTAX INTEGER (1..100) MAX-ACCESS read-write STATUS current DESCRIPTION "This is the % of max power to transmit at." ::= { extremeWirelessPhysInterfaceRFCtlEntry 2 } extremeWirelessPhysInterfaceDTIMPeriod OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION "This is the DTIM period." ::= { extremeWirelessPhysInterfaceRFCtlEntry 3 } extremeWirelessPhysInterfaceFragLength OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION " " REFERENCE "ieee802dot11.2.1.1.5." ::= { extremeWirelessPhysInterfaceRFCtlEntry 4 } extremeWirelessPhysInterfaceLongRetry OBJECT-TYPE SYNTAX INTEGER (1..255) MAX-ACCESS read-write STATUS current DESCRIPTION "Attribute indicates the maximum number of transmission attempts of a frame whose size is > RTS." REFERENCE "dot11LongRetryLimit" ::= { extremeWirelessPhysInterfaceRFCtlEntry 5 } extremeWirelessPhysInterfaceShortRetry OBJECT-TYPE SYNTAX INTEGER (1..255) MAX-ACCESS read-write STATUS current DESCRIPTION "Attribute indicates the maximum number of transmission attempts of a frame whose size is <= RTS." REFERENCE "dot11ShortRetryLimit" ::= { extremeWirelessPhysInterfaceRFCtlEntry 6 } extremeWirelessPhysInterfaceRTSThreshold OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION " " REFERENCE "ieee802dot11.2.1.1.2." ::= { extremeWirelessPhysInterfaceRFCtlEntry 7 } extremeWirelessPhysInterfaceSupportedDataRatesRxValue OBJECT-TYPE SYNTAX Dot11Speed MAX-ACCESS read-only STATUS current DESCRIPTION "A bitmask of all supported datarates for Rx." ::= { extremeWirelessPhysInterfaceRFCtlEntry 8 } extremeWirelessPhysInterfaceSupportedDataRatesTxValue OBJECT-TYPE SYNTAX Dot11Speed MAX-ACCESS read-only STATUS current DESCRIPTION "A bitmask of all supported datarates for Tx." ::= { extremeWirelessPhysInterfaceRFCtlEntry 9 } extremeWirelessPhysInterfacePHYType OBJECT-TYPE SYNTAX Dot11Type MAX-ACCESS read-write STATUS current DESCRIPTION "This variable selects between 802.11 a/b/g for this transmitter. It should be used by ap to range check frequency, etc." ::= { extremeWirelessPhysInterfaceRFCtlEntry 10 } extremeWirelessPhysInterfacePHYSupportedTypes OBJECT-TYPE SYNTAX BITS { bsupported(0), asupported(1), gsupported(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "This is the 802.11 standard supported by this interface as a bitmask" ::= { extremeWirelessPhysInterfaceRFCtlEntry 11 } extremeWirelessPhysInterfacePreamble OBJECT-TYPE SYNTAX INTEGER { short(0), long(1) } MAX-ACCESS read-write STATUS current DESCRIPTION "This changes the 802 preamble expected by the interface." ::= { extremeWirelessPhysInterfaceRFCtlEntry 12 } extremeWirelessPhysInterfaceAbsTxPowerLevel OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "This is the absolute value of max power to transmit level in dBm." ::= { extremeWirelessPhysInterfaceRFCtlEntry 13 } -- *************************************************************** -- -- Wireless Interface Status Table -- *************************************************************** -- extremeWirelessInterfaceStatusTable OBJECT-TYPE SYNTAX SEQUENCE OF ExtremeWirelessInterfaceStatusEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table provides statistics and information on the current condition of each wireless interace. There is one entry per virtual and physical wireless interface in this table. The values for the physical interfaces represent the sum of the values for all sub interfaces." ::= { extremeAP 5 } extremeWirelessInterfaceStatusEntry OBJECT-TYPE SYNTAX ExtremeWirelessInterfaceStatusEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Each entry in this table is indexed by either a virtual or a physical ifIndex." INDEX { ifIndex } ::= { extremeWirelessInterfaceStatusTable 1 } ExtremeWirelessInterfaceStatusEntry ::= SEQUENCE { extremeWirelessIntfTotalDetected Unsigned32, extremeWirelessIntfTotalAuthed Unsigned32, extremeWirelessIntfTotalAuthFailed Unsigned32, extremeWirelessIntfTotalAssoc Unsigned32, extremeWirelessIntfTotalAssocFailed Unsigned32, extremeWirelessIntfRateDetected Unsigned32, extremeWirelessIntfRateAuthed Unsigned32, extremeWirelessIntfRateAuthFailed Unsigned32, extremeWirelessIntfRateAssoc Unsigned32, extremeWirelessIntfRateAssocFailed Unsigned32, extremeWirelessIntfBlockTime Unsigned32, extremeWirelessIntfCurrentDetected Unsigned32, extremeWirelessIntfCurrentAuthed Unsigned32, extremeWirelessIntfCurrentAssoc Unsigned32, extremeWirelessIntfCurrentForwarding Unsigned32} extremeWirelessIntfTotalDetected OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This gives the total number of stations which have entered the detected state on this wireless interface since the last time the counters were cleared." ::= { extremeWirelessInterfaceStatusEntry 1 } extremeWirelessIntfTotalAuthed OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This gives the total number of stations which have entered the authenticated state on this wireless interface since the last time the counters were cleared. Note that this is equal to the number of stations which have entered the forwarding state. This is not necessaryly equivalent to the number of stations which have succeeded in MAC-level authentication." ::= { extremeWirelessInterfaceStatusEntry 2 } extremeWirelessIntfTotalAuthFailed OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This gives the total number of stations which have failed to authenticate on this wireless interface. Note that no distinction is made between a MAC-layer or higher-layer authentication failure." ::= { extremeWirelessInterfaceStatusEntry 3 } extremeWirelessIntfTotalAssoc OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This gives the total number of stations which have entered the associated state on this wireless interface since the last time the counters were cleared." ::= { extremeWirelessInterfaceStatusEntry 4 } extremeWirelessIntfTotalAssocFailed OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This gives the total number of stations which have failed the association on this wireless interface since the last time the counters were cleared." ::= { extremeWirelessInterfaceStatusEntry 5 } extremeWirelessIntfRateDetected OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This gives the rate of clients being detected on this interface over a 5 second period using EMWA averaging." ::= { extremeWirelessInterfaceStatusEntry 6 } extremeWirelessIntfRateAuthed OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This gives teh rate of clients being authenticated on this interface over a 5 second period using EMWA averaging." ::= { extremeWirelessInterfaceStatusEntry 7 } extremeWirelessIntfRateAuthFailed OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This gives the rate of clients failed authentication on this interface over a 5 second period using EMWA averaging." ::= { extremeWirelessInterfaceStatusEntry 8 } extremeWirelessIntfRateAssoc OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This gives the rate of clients being associated on this interface over a 5 second period using EMWA averaging." ::= { extremeWirelessInterfaceStatusEntry 9 } extremeWirelessIntfRateAssocFailed OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This gives the rate of clients failing association on this interface over a 5 second period using EMWA averaging." ::= { extremeWirelessInterfaceStatusEntry 10 } extremeWirelessIntfBlockTime OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This value specifies the number of ticks until traffic will be allowed back on this interface. A non-zero value indicates that traffic has been blocked, most likely due to countermeasures." ::= { extremeWirelessInterfaceStatusEntry 11 } extremeWirelessIntfCurrentDetected OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This gives the current number of stations which are in the detected state on this wireless interface." ::= { extremeWirelessInterfaceStatusEntry 12 } extremeWirelessIntfCurrentAuthed OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This gives the current number of stations which are in the authenticated state on this wireless interface." ::= { extremeWirelessInterfaceStatusEntry 13 } extremeWirelessIntfCurrentAssoc OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This gives the current number of stations which are in the associated state on this wireless interface." ::= { extremeWirelessInterfaceStatusEntry 14 } extremeWirelessIntfCurrentForwarding OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This gives the current number of stations which are in the forwarding state on this wireless interface." ::= { extremeWirelessInterfaceStatusEntry 15 } --TODO: Do we need to fix this table -- *************************************************************** -- -- AP Wireless Client Table -- -- *************************************************************** -- extremeWirelessClientTable OBJECT-TYPE SYNTAX SEQUENCE OF ExtremeWirelessClientEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table augments the Dot11AccessPointAddressTableEntry to add a per-client VLAN entry." ::= { extremeAP 11 } extremeWirelessClientEntry OBJECT-TYPE SYNTAX ExtremeWirelessClientEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in the extremeWirelessClientTable. It is possible for there to be multiple IEEE 802.11 interfaces on one agent, each with its unique MAC address. The relationship between an IEEE 802.11 interface and an interface in the context of the Internet-standard MIB is one-to-one. As such, the value of an ifIndex object instance can be directly used to identify corresponding instances of the objects defined herein. by ifIndex." INDEX {ifIndex, extremeWirelessClientID} ::= { extremeWirelessClientTable 1 } ExtremeWirelessClientEntry ::= SEQUENCE { extremeWirelessClientID MacAddress, extremeWirelessClientState INTEGER, extremeWirelessClientEncryption WPACipherSet, extremeWirelessClientSignalStrength INTEGER, extremeWirelessClientLinkQuality INTEGER, extremeWirelessClientVLAN INTEGER, extremeWirelessClientPriority INTEGER, extremeWirelessClientAuthType ClientAuthType, extremeWirelessClientLastStateChangeTime TimeTicks, extremeWirelessClientTxFrames Counter32, extremeWirelessClientRxFrames Counter32, extremeWirelessClientTxBytes Counter64, extremeWirelessClientRxBytes Counter64, extremeWirelessClientLastPacketType INTEGER, extremeWirelessClientSSID OCTET STRING, extremeWirelessClientStatus RowStatus, extremeWirelessClientIP IpAddress, extremeWirelessClientUsername DisplayString, extremeWirelessClientDecryptionFailures Counter32, extremeWirelessClientMICFailures Counter32} extremeWirelessClientID OBJECT-TYPE SYNTAX MacAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The Unique MAC Address of the station for which this address table entry pertains." ::= { extremeWirelessClientEntry 1 } extremeWirelessClientState OBJECT-TYPE SYNTAX INTEGER { detected (1), authenticated (2), associated (3) , data-forwarding (4)} MAX-ACCESS read-only STATUS current DESCRIPTION "This attribute shall indicate the current state of the connection between a wireless station and the AP. The attribute is enumerated as follows: 1 - Detected - station has been detected, but not is communicating with AP 2 - Authenticated - station is authenticated but not currently associated. 3 - Associated - station is authenticated and associated 4 - Data-forwarding - station is on the network It is assumed that if an station is deauthenticated, or disassociated then it no longer has an entry the AP's Address Table." ::= { extremeWirelessClientEntry 2 } extremeWirelessClientEncryption OBJECT-TYPE SYNTAX WPACipherSet MAX-ACCESS read-only STATUS current DESCRIPTION "This attribute is contains the encryption mechanism being used by the station in an AP that allows mixed encryption modes." ::= { extremeWirelessClientEntry 3 } extremeWirelessClientSignalStrength OBJECT-TYPE SYNTAX INTEGER (1..100) MAX-ACCESS read-only STATUS current DESCRIPTION "This attribute shall specify the signal strength of the last frame received from the station in - dBm. e.g. a value of 50 implies -50 dBm." ::= { extremeWirelessClientEntry 4 } extremeWirelessClientLinkQuality OBJECT-TYPE SYNTAX INTEGER (1..100) MAX-ACCESS read-only STATUS current DESCRIPTION "This attribute shall contain an indication of the quality of the signal as measured in the last frame received from the station. TBD format of this attribute" ::= { extremeWirelessClientEntry 5 } extremeWirelessClientVLAN OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "This is the per-client VLAN which was pushed over by a RADIUS server or other mechanism." ::= { extremeWirelessClientEntry 6 } extremeWirelessClientPriority OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "This is a per-client 802.1p value which was either configured by the RADIUS server or statically through the port configuration table." ::= { extremeWirelessClientEntry 7 } extremeWirelessClientAuthType OBJECT-TYPE SYNTAX ClientAuthType MAX-ACCESS read-only STATUS current DESCRIPTION "This is an indication of what access method was used to authenticated the client. The strongest mechanism used should be listed here, in case more than one was used. For example, if a combination of mac-based shared-key and dot1x were used, this value should indicated dot1x." ::= { extremeWirelessClientEntry 8 } extremeWirelessClientLastStateChangeTime OBJECT-TYPE SYNTAX TimeTicks MAX-ACCESS read-only STATUS current DESCRIPTION "This is the sysUpTime of the switch when the clients state changed last" ::= { extremeWirelessClientEntry 9 } extremeWirelessClientTxFrames OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "This is the number of packets transmitted to the client" ::= { extremeWirelessClientEntry 10 } extremeWirelessClientRxFrames OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "This is the number of packets transmitted by the client" ::= { extremeWirelessClientEntry 11 } extremeWirelessClientTxBytes OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "This is the number of bytes transmitted to the client" ::= { extremeWirelessClientEntry 12 } extremeWirelessClientRxBytes OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "This is the number of bytes transmitted by the client" ::= { extremeWirelessClientEntry 13 } extremeWirelessClientLastPacketType OBJECT-TYPE SYNTAX INTEGER { data (0), psPoll (1), probeRequest (2), disassociation (3), deauthentication (4), association (5), reassociation (6), authentication (7) } -- inf-beacon (8), -- adhoc-beacon (9) } MAX-ACCESS read-only STATUS current DESCRIPTION "This the the last packet type seen from the specific client" ::= { extremeWirelessClientEntry 14 } extremeWirelessClientSSID OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-only STATUS current DESCRIPTION "The SSID that this client was using" ::= { extremeWirelessClientEntry 15 } extremeWirelessClientStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-write STATUS current DESCRIPTION "This variable is used to delete an entry from the table. The only value this can be set to, is delete (6). If an entry is deleted, that is already in Associated or data-forwarding state, then the AP should dis-associate the particular client by sending a disassociate message. If an entry is in Authenticated state, and is deleted, then the AP should 'deAuthenticate' that client. If an entry is in 'detected' state and is deleted, then the entry should just be removed from the table." ::= { extremeWirelessClientEntry 16 } extremeWirelessClientIP OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "IP Address of the wireless client." ::= { extremeWirelessClientEntry 17 } extremeWirelessClientUsername OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "Username (if any) of the wireless client." ::= { extremeWirelessClientEntry 18 } extremeWirelessClientDecryptionFailures OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "This is the number of failures during decrypting packets from this client." ::= { extremeWirelessClientEntry 19 } extremeWirelessClientMICFailures OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "This is the number of MIC failures for this client." ::= { extremeWirelessClientEntry 20 } -- *************************************************************** -- -- RF Profile Table -- -- *************************************************************** -- extremeRFProfile OBJECT IDENTIFIER ::= { extremeProfile 1 } extremeRFProfileTable OBJECT-TYPE SYNTAX SEQUENCE OF ExtremeRFProfileEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "There is one entry in this table for each RF profile defined on the LAC. Configuration for wireless intf. should only be done by manipulating these variables. Changes here will be reflected in the corresponding 802dot11 MIB variables (see references below). On bootup this table should be populated with one default entry for each supported type (A, G, etc)." ::= { extremeRFProfile 1 } extremeRFProfileEntry OBJECT-TYPE SYNTAX ExtremeRFProfileEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "" INDEX { extremeRFProfileIndex } ::= { extremeRFProfileTable 1 } ExtremeRFProfileEntry ::= SEQUENCE { extremeRFProfileIndex INTEGER, extremeRFProfileName DisplayString, extremeRFProfileType Dot11Type, extremeRFProfileBeaconInterval INTEGER, extremeRFProfileDTIM INTEGER, extremeRFProfileFragLength INTEGER, extremeRFProfileRTSThresh INTEGER, extremeRFProfilePreamble INTEGER, extremeRFProfileShortRetry INTEGER, extremeRFProfileLongRetry INTEGER, extremeRFProfileStatus RowStatus } extremeRFProfileIndex OBJECT-TYPE SYNTAX INTEGER(1..34) MAX-ACCESS not-accessible STATUS current DESCRIPTION "Integer index for this table. This is here to avoid having to index into the table via the string name." ::= { extremeRFProfileEntry 1 } extremeRFProfileName OBJECT-TYPE SYNTAX DisplayString (SIZE(1..32)) MAX-ACCESS read-create STATUS current DESCRIPTION "String name of this profile. The value |default| is a special token and should not be allowed." ::= { extremeRFProfileEntry 2 } extremeRFProfileType OBJECT-TYPE SYNTAX Dot11Type MAX-ACCESS read-create STATUS current DESCRIPTION "This is the type of this RF profile. This will decide the ranges of some of the values (i.e. channel)." ::= { extremeRFProfileEntry 3 } extremeRFProfileBeaconInterval OBJECT-TYPE SYNTAX INTEGER(1..65535) MAX-ACCESS read-create STATUS current DESCRIPTION "This is the number of TU between beacon frames." REFERENCE "ieee802dot11.1.1.1.12." ::= { extremeRFProfileEntry 5 } extremeRFProfileDTIM OBJECT-TYPE SYNTAX INTEGER(1..255) MAX-ACCESS read-create STATUS current DESCRIPTION " " REFERENCE "ieee802dot11.1.1.1.13." ::= { extremeRFProfileEntry 6 } extremeRFProfileFragLength OBJECT-TYPE SYNTAX INTEGER(256..2345) MAX-ACCESS read-create STATUS current DESCRIPTION " " REFERENCE "ieee802dot11.2.1.1.5." ::= { extremeRFProfileEntry 7 } extremeRFProfileRTSThresh OBJECT-TYPE SYNTAX INTEGER(0..2347) MAX-ACCESS read-create STATUS current DESCRIPTION " " REFERENCE "ieee802dot11.2.1.1.2." ::= { extremeRFProfileEntry 8 } extremeRFProfilePreamble OBJECT-TYPE SYNTAX INTEGER { short(0), long(1) } MAX-ACCESS read-create STATUS current DESCRIPTION "This changes the 802 preamble expected by the interface." ::= { extremeRFProfileEntry 9 } extremeRFProfileShortRetry OBJECT-TYPE SYNTAX INTEGER (1..255) MAX-ACCESS read-create STATUS current DESCRIPTION "Attribute indicates the maximum number of transmission attempts of a frame whose size is <= RTS." REFERENCE "dot11ShortRetryLimit" ::= { extremeRFProfileEntry 11 } extremeRFProfileLongRetry OBJECT-TYPE SYNTAX INTEGER (1..255) MAX-ACCESS read-create STATUS current DESCRIPTION "Attribute indicates the maximum number of transmission attempts of a frame whose size is > RTS." REFERENCE "dot11LongRetryLimit" ::= { extremeRFProfileEntry 12 } extremeRFProfileStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "Standard row-status semantics." ::= { extremeRFProfileEntry 13 } -- *************************************************************** -- -- Security Profile Table -- -- *************************************************************** -- extremeSecurityProfile OBJECT IDENTIFIER ::= { extremeProfile 2 } extremeSecurityProfileTable OBJECT-TYPE SYNTAX SEQUENCE OF ExtremeSecurityProfileEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "There is one entry in this table per security profile on the LAC. Each profile is identified by a string name." ::= { extremeSecurityProfile 1 } extremeSecurityProfileEntry OBJECT-TYPE SYNTAX ExtremeSecurityProfileEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "" INDEX { extremeSecurityProfileIndex } ::= { extremeSecurityProfileTable 1 } ExtremeSecurityProfileEntry ::= SEQUENCE { extremeSecurityProfileIndex INTEGER, extremeSecurityProfileName DisplayString, extremeSecurityProfileESSName OCTET STRING, extremeSecurityProfileSSIDInBeacon TruthValue, extremeSecurityProfileDot11AuthMode Dot11AuthMode, extremeSecurityProfileNetworkAuthMode NetworkAuthMode, extremeSecurityProfileDataVlan INTEGER, extremeSecurityProfileIgnoreVSAVlan TruthValue, extremeSecurityWEPDefaultKey INTEGER, extremeSecurityProfileEncryptionLength INTEGER, extremeSecurityProfileStatus RowStatus } extremeSecurityProfileIndex OBJECT-TYPE SYNTAX INTEGER(1..32) MAX-ACCESS not-accessible STATUS current DESCRIPTION "This is an integer index used instead of string name." ::= { extremeSecurityProfileEntry 1 } extremeSecurityProfileName OBJECT-TYPE SYNTAX DisplayString (SIZE(1..32)) MAX-ACCESS read-create STATUS current DESCRIPTION "This is a unique string name which identifies this profile. The token |default| is special and should not be allowed." ::= { extremeSecurityProfileEntry 2 } extremeSecurityProfileESSName OBJECT-TYPE SYNTAX OCTET STRING (SIZE(0..32)) MAX-ACCESS read-create STATUS current DESCRIPTION "This is the desired ESS name." REFERENCE "ieee802dot11.1.1.1.9" ::= { extremeSecurityProfileEntry 3 } extremeSecurityProfileSSIDInBeacon OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-create STATUS current DESCRIPTION "Setting this value to true will have the channel place the ssid in the beacon frame." ::= { extremeSecurityProfileEntry 4 } extremeSecurityProfileDot11AuthMode OBJECT-TYPE SYNTAX Dot11AuthMode MAX-ACCESS not-accessible STATUS current DESCRIPTION "Specified whether to use open or shared authentication" ::= { extremeSecurityProfileEntry 5 } extremeSecurityProfileNetworkAuthMode OBJECT-TYPE SYNTAX NetworkAuthMode MAX-ACCESS not-accessible STATUS current DESCRIPTION "This specifies the authentication to use on top of dot11 mac authentication" ::= { extremeSecurityProfileEntry 6 } extremeSecurityProfileDataVlan OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS not-accessible STATUS current DESCRIPTION "This specifies the VLAN to use in case it does not come back as a VSA or in case the IgnoreVSAVlan is set to true" ::= { extremeSecurityProfileEntry 7 } extremeSecurityProfileIgnoreVSAVlan OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-create STATUS current DESCRIPTION "This specifies if Vlan associations in VSAs from the radius server has to be ignored or not" ::= { extremeSecurityProfileEntry 8 } extremeSecurityWEPDefaultKey OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-create STATUS current DESCRIPTION "This value indicates the index in extremeWEPKeyTable that identifies the key this interface will use to decrypt packets." ::= { extremeSecurityProfileEntry 9 } extremeSecurityProfileEncryptionLength OBJECT-TYPE SYNTAX INTEGER { none(0), sixtyfour(64), onetwentyeight(128) } MAX-ACCESS read-create STATUS current DESCRIPTION "This gives the size in bits of the key. This variable defines the length of all WEP keys and also the encryption to use in case of legacy dot1x. If the encryption is set to none then no WEP encryption is set." ::= { extremeSecurityProfileEntry 10 } -- extremeSecurityEnableWebNetlogin OBJECT-TYPE -- SYNTAX TruthValue -- MAX-ACCESS read-create -- STATUS current -- DESCRIPTION -- "Enable disable netlogin on the wireless interface where -- security profile is applied." -- ::= { extremeSecurityProfileEntry 11 } extremeSecurityProfileStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "Standard row-creation semantics." ::= { extremeSecurityProfileEntry 11 } extremeSecurityDot1xConfigTable OBJECT-TYPE SYNTAX SEQUENCE OF ExtremeSecurityDot1xConfigEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "There is one entry in this table per security profile on the LAC. It reflects the dot1x security config" ::= { extremeSecurityProfile 2 } extremeSecurityDot1xConfigEntry OBJECT-TYPE SYNTAX ExtremeSecurityDot1xConfigEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "" INDEX { extremeSecurityProfileIndex } ::= { extremeSecurityDot1xConfigTable 1 } ExtremeSecurityDot1xConfigEntry ::= SEQUENCE { extremeSecurityKeyMgmtSuite WPAKeyMgmtSet, extremeSecurityMcastCipherSuite WPACipherSet, extremeSecurityDot1xPSKValue OCTET STRING, extremeSecurityDot1xPSKPassPhrase DisplayString, extremeSecurityDot1xReAuthPeriod INTEGER, extremeSecurityGroupUpdateTimeOut Unsigned32, extremeSecurityPairwiseUpdateTimeOut Unsigned32, extremeSecurityDot11iPreauthEnabled TruthValue } extremeSecurityKeyMgmtSuite OBJECT-TYPE SYNTAX WPAKeyMgmtSet MAX-ACCESS read-write STATUS current DESCRIPTION "This bitmask configures the authentication suites to be used." ::= { extremeSecurityDot1xConfigEntry 1 } extremeSecurityMcastCipherSuite OBJECT-TYPE SYNTAX WPACipherSet MAX-ACCESS read-write STATUS current DESCRIPTION "This configures the cipher suite to use for mcast traffic. The cipher suite to use for unicast traffic is derived from this using the following algorithm: Mcast cipher = WEP (64/128), Unicast cipher = TKIP Mcast cipher = TKIP, Unicast cipher = TKIP Mcast cipher = AES, Unicast cipher = AES. This therefore determines the max unicast cipher suite the client can use to associate with this interface." ::= { extremeSecurityDot1xConfigEntry 2 } extremeSecurityDot1xPSKValue OBJECT-TYPE SYNTAX OCTET STRING (SIZE(32)) MAX-ACCESS read-write STATUS current DESCRIPTION "The Pre-Shared Key (PSK) for when RSN in PSK mode is the selected authentication suite." REFERENCE "dot11RSNConfigPSKValue" ::= { extremeSecurityDot1xConfigEntry 3 } extremeSecurityDot1xPSKPassPhrase OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-write STATUS current DESCRIPTION "The PSK, for when WPA in PSK mode is the selected authentication suite, is configured by extremeSecurityKeyMgmtSuite. An alternative manner of setting the PSK uses the password-to-key algorithm defined in section XXX. This variable provides a means to enter a pass phrase. When this object is written, the RSN entity shall use the password-to-key algorithm specified in section XXX to derive a pre-shared and populate extremeSecurityDot1xPSKValue with this key. This object is logically write-only. Reading this variable shall return unsuccessful status or null or zero." ::= { extremeSecurityDot1xConfigEntry 4 } extremeSecurityDot1xReAuthPeriod OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION "Number of seconds a clients authentication will last before the AP automatically issues a reauthentication request." ::= { extremeSecurityDot1xConfigEntry 5 } extremeSecurityGroupUpdateTimeOut OBJECT-TYPE SYNTAX Unsigned32 (1..1440) UNITS "minutes" MAX-ACCESS read-write STATUS current DESCRIPTION "The time in minutes after which the RSN group update handshake will be retried. The timer shall start at the moment the group update message is sent." REFERENCE "dot11RSNConfigGroupUpdateTimeOut" DEFVAL { 100 } -- ::= { extremeSecurityDot1xConfigEntry 6 } extremeSecurityPairwiseUpdateTimeOut OBJECT-TYPE SYNTAX Unsigned32 (1..1440) UNITS "minutes" MAX-ACCESS read-write STATUS current DESCRIPTION "The time in minutes after which the RSN 4-way handshake will be retried. The timer shall start at the moment a 4-way message is sent." REFERENCE "dot11RSNConfigPairwiseUpdateTimeOut" DEFVAL { 100 } -- ::= { extremeSecurityDot1xConfigEntry 7 } extremeSecurityDot11iPreauthEnabled OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "Whether preauth is enabled or not" ::= { extremeSecurityDot1xConfigEntry 8 } -- *************************************************************** -- -- Default WEP Key Table -- -- *************************************************************** -- extremeWEPKeyTable OBJECT-TYPE SYNTAX SEQUENCE OF ExtremeWEPKeyEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains per-profile WEP keys. Reference ieee802dot11.1.2.3." ::= { extremeSecurityProfile 4 } extremeWEPKeyEntry OBJECT-TYPE SYNTAX ExtremeWEPKeyEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION " " INDEX { extremeSecurityProfileIndex, extremeWEPKeyIndex } ::= { extremeWEPKeyTable 1 } ExtremeWEPKeyEntry ::= SEQUENCE { extremeWEPKeyIndex INTEGER, extremeWEPKey OCTET STRING, extremeWEPKeyStatus RowStatus } extremeWEPKeyIndex OBJECT-TYPE SYNTAX INTEGER(0..8) MAX-ACCESS not-accessible STATUS current DESCRIPTION "There can be upto 8 wep keys for any wireless interface. Four of the keys are to be used with WEP Authentication, and the other four with MAC Auth." ::= { extremeWEPKeyEntry 1 } extremeWEPKey OBJECT-TYPE SYNTAX OCTET STRING (SIZE(1..19)) MAX-ACCESS read-create STATUS current DESCRIPTION "This is a write-only wep key." ::= { extremeWEPKeyEntry 2 } extremeWEPKeyStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "Standard row-creation semantics." ::= { extremeWEPKeyEntry 3 } -- *************************************************************** -- -- Wireless Physical Interface Config Table -- -- *************************************************************** -- extremeWirelessPhysInterfaceConfigTable OBJECT-TYPE SYNTAX SEQUENCE OF ExtremeWirelessPhysInterfaceConfigEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains the configured bindings between physical wireless interfaces and RF profiles and other RF properties. There is one instance of a physical wireless interface per radio on the AP. Entries in this table have a duration that exceeds the lifetime of entries in the wirelessPhysInterfaceCtlTable. A configured binding spans the reset or removal of a wireless interface. Entries can be removed from this table by the user. If there is a mismatch between a new wireless port and a previously configured profile, the default profile will be applied and this table will be updated." ::= { extremeProfile 3 } extremeWirelessPhysInterfaceConfigEntry OBJECT-TYPE SYNTAX ExtremeWirelessPhysInterfaceConfigEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION " " INDEX { extremeWirelessPhysInterfaceIndex } ::= { extremeWirelessPhysInterfaceConfigTable 1 } ExtremeWirelessPhysInterfaceConfigEntry ::= SEQUENCE { extremeWirelessPhysInterfaceConfigRFProfile INTEGER, extremeWirelessPhysInterfaceConfigRFChannel INTEGER, extremeWirelessPhysInterfaceConfigSpeed Dot11Speed, extremeWirelessPhysInterfaceConfigPowerLevel INTEGER } extremeWirelessPhysInterfaceConfigRFProfile OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-create STATUS current DESCRIPTION "This is the index into the extremeRFProfileTable for the RF profile that this wireless interface is bound to. The default value is equivalent to the profile index for the interface-appropriate default in the table." ::= { extremeWirelessPhysInterfaceConfigEntry 1 } extremeWirelessPhysInterfaceConfigRFChannel OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-create STATUS current DESCRIPTION "This is the RF channel which has been selected for this wireless interface. It should be one of the supported channels as given by the phy tables in the dot11 mib." ::= { extremeWirelessPhysInterfaceConfigEntry 2 } extremeWirelessPhysInterfaceConfigSpeed OBJECT-TYPE SYNTAX Dot11Speed MAX-ACCESS read-create STATUS current DESCRIPTION "This is the speed to configure the interface at. A value of 0 indicates automatic speed detection." ::= { extremeWirelessPhysInterfaceConfigEntry 3 } extremeWirelessPhysInterfaceConfigPowerLevel OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-create STATUS current DESCRIPTION "This value specifies the tx power (in % of max power) to use." ::= { extremeWirelessPhysInterfaceConfigEntry 4 } -- *************************************************************** -- -- Wireless Virtual Interface Config Table -- -- *************************************************************** -- extremeWirelessVirtInterfaceConfigTable OBJECT-TYPE SYNTAX SEQUENCE OF ExtremeWirelessVirtInterfaceConfigEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains the configured bindings between virtual wireless interfaces and security profiles and other security properties. There are upto 8 virtual interface for each physical interface. Entries in this table have a duration that exceeds the lifetime of entries in the wirelessVirtInterfaceCtlTable. A configured binding spans the reset or removal of a wireless interface. Entries can be removed from this table by the user." ::= { extremeProfile 4 } extremeWirelessVirtInterfaceConfigEntry OBJECT-TYPE SYNTAX ExtremeWirelessVirtInterfaceConfigEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION " " INDEX { extremeWirelessVirtInterfaceIndex } ::= { extremeWirelessVirtInterfaceConfigTable 1 } ExtremeWirelessVirtInterfaceConfigEntry ::= SEQUENCE { extremeWirelessVirtInterfaceConfigSecurityProfile INTEGER, extremeWirelessVirtInterfaceConfigMaxClients INTEGER, extremeWirelessVirtInterfaceConfigWirelessBridging TruthValue, extremeWirelessVirtInterfaceConfigState INTEGER } extremeWirelessVirtInterfaceConfigSecurityProfile OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION "This is the index into the extremeSecurityProfileTable for the security profile that this wireless interface is bound to. The default value is equivalent to the profile index for the interface-appropriate default in the table." ::= { extremeWirelessVirtInterfaceConfigEntry 1 } extremeWirelessVirtInterfaceConfigMaxClients OBJECT-TYPE SYNTAX INTEGER (1..128) MAX-ACCESS read-only STATUS current DESCRIPTION "The maximum number of clients that can associate with this virtual interface." ::= { extremeWirelessVirtInterfaceConfigEntry 2 } extremeWirelessVirtInterfaceConfigWirelessBridging OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "This specifies whether wireless bridging is enabled on this interface. If wireless bridging is enabled then traffic originating from a client on this interface will be bridged to clients on the same VLAN on this or other virtual interfaces that have wireless bridging enabled. So basically wireless bridging should be enabled on both the source and the destination virtual interface for traffic to be bridged." ::= { extremeWirelessVirtInterfaceConfigEntry 3 } extremeWirelessVirtInterfaceConfigState OBJECT-TYPE SYNTAX INTEGER { enabled(0), disabled(1) } MAX-ACCESS read-write STATUS current DESCRIPTION "This value specifies whether the virtual interface is active or not" ::= { extremeWirelessVirtInterfaceConfigEntry 4 } -- *************************************************************** -- -- Antenna Profile Table -- -- *************************************************************** -- extremeAntennaProfile OBJECT IDENTIFIER ::= { extremeProfile 5 } extremeAntennaProfileTable OBJECT-TYPE SYNTAX SEQUENCE OF ExtremeAntennaProfileEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "There is one entry in this table per antenna profile on the LAC. Each profile is identified by a string name." ::= { extremeAntennaProfile 1 } extremeAntennaProfileEntry OBJECT-TYPE SYNTAX ExtremeAntennaProfileEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "" INDEX { extremeAntennaProfileIndex } ::= { extremeAntennaProfileTable 1 } ExtremeAntennaProfileEntry ::= SEQUENCE { extremeAntennaProfileIndex INTEGER, extremeAntennaProfileName DisplayString, extremeAntennaProfile2point4GHZGain INTEGER, extremeAntennaProfile5GHZGain INTEGER, extremeAntennaProfileStatus RowStatus } extremeAntennaProfileIndex OBJECT-TYPE SYNTAX INTEGER(1..32) MAX-ACCESS not-accessible STATUS current DESCRIPTION "This is an integer index used instead of string name." ::= { extremeAntennaProfileEntry 1 } extremeAntennaProfileName OBJECT-TYPE SYNTAX DisplayString (SIZE(1..32)) MAX-ACCESS read-create STATUS current DESCRIPTION "This is a unique string name which identifies this profile. The token |default| is special and should not be allowed." ::= { extremeAntennaProfileEntry 2 } extremeAntennaProfile2point4GHZGain OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-create STATUS current DESCRIPTION "This specifies 2.4GHz gain value for detachable antenna in dbi" ::= { extremeAntennaProfileEntry 3 } extremeAntennaProfile5GHZGain OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-create STATUS current DESCRIPTION "This specifies 5GHz gain value for detachable antenna in dbi" ::= { extremeAntennaProfileEntry 4 } extremeAntennaProfileStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "Standard row-creation semantics." ::= { extremeAntennaProfileEntry 5 } -- *************************************************************** -- -- RemoteConnect configuration -- -- *************************************************************** -- extremeWirelessRemoteConnectGlobalCfgGroup OBJECT IDENTIFIER ::= { extremeProfile 6 } extremeWirelessRemoteConnectGlobalBindingType OBJECT-TYPE SYNTAX WirelessRemoteConnectBindingType MAX-ACCESS read-write STATUS current DESCRIPTION "Global Binding Tye" ::= { extremeWirelessRemoteConnectGlobalCfgGroup 1 } extremeWirelessRemoteConnectBindingTable OBJECT-TYPE SYNTAX SEQUENCE OF ExtremeWirelessRemoteConnectBindingEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table specifies the RemoteConnect binding configuration for various ports." ::= { extremeProfile 7 } extremeWirelessRemoteConnectBindingEntry OBJECT-TYPE SYNTAX ExtremeWirelessRemoteConnectBindingEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION " " INDEX { extremeWirelessRemoteConnectBindingPortIndex } ::= { extremeWirelessRemoteConnectBindingTable 1 } ExtremeWirelessRemoteConnectBindingEntry ::= SEQUENCE { extremeWirelessRemoteConnectBindingPortIndex INTEGER, extremeWirelessRemoteConnectBindingIfIndex Integer32, extremeWirelessRemoteConnectBindingType WirelessRemoteConnectBindingType, extremeWirelessRemoteConnectBindingMAC MacAddress, extremeWirelessRemoteConnectBindingSerial OCTET STRING, extremeWirelessRemoteConnectBindingIPAddressType InetAddressType, extremeWirelessRemoteConnectBindingIPAddress InetAddress, extremeWirelessRemoteConnectBindingEnabled TruthValue, extremeWirelessRemoteConnectBindingBound TruthValue, extremeWirelessRemoteConnectBindingRowStatus RowStatus} extremeWirelessRemoteConnectBindingPortIndex OBJECT-TYPE SYNTAX INTEGER(1..48) MAX-ACCESS not-accessible STATUS current DESCRIPTION "The index of this binding. This maps one-to-one with the value specified in the CLI. For example, if you say v:1 in the CLI, then this value should be 1." ::= { extremeWirelessRemoteConnectBindingEntry 1} extremeWirelessRemoteConnectBindingIfIndex OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "This is the IF index that is used in the extremeWirelessPortConfigTable etc to refer to this RemoteConnect port." ::= { extremeWirelessRemoteConnectBindingEntry 2} extremeWirelessRemoteConnectBindingType OBJECT-TYPE SYNTAX WirelessRemoteConnectBindingType MAX-ACCESS read-create STATUS current DESCRIPTION "This is the type of binding. Based on this, one of the following columns will be valid." ::= { extremeWirelessRemoteConnectBindingEntry 3 } extremeWirelessRemoteConnectBindingMAC OBJECT-TYPE SYNTAX MacAddress MAX-ACCESS read-create STATUS current DESCRIPTION "The MAC address of the AP that is bound to this virtual port. This is valid only if the extremeWirelessRemoteConnectBindingType is set to mac-address" ::= { extremeWirelessRemoteConnectBindingEntry 4} extremeWirelessRemoteConnectBindingSerial OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-create STATUS current DESCRIPTION "The serial number of the AP that is bound to this virtual port. This is valid only if the extremeWirelessRemoteConnectBindingType is set to serial-number" ::= { extremeWirelessRemoteConnectBindingEntry 5} extremeWirelessRemoteConnectBindingIPAddressType OBJECT-TYPE SYNTAX InetAddressType MAX-ACCESS read-create STATUS current DESCRIPTION "The IP address type of the AP that is bound to this virtual port. This is valid only if the extremeWirelessRemoteConnectBindingType is set to ip-address" ::= { extremeWirelessRemoteConnectBindingEntry 6} extremeWirelessRemoteConnectBindingIPAddress OBJECT-TYPE SYNTAX InetAddress MAX-ACCESS read-create STATUS current DESCRIPTION "The IP address of the AP that is bound to this virtual port. This is valid only if the extremeWirelessRemoteConnectBindingType is set to ip-address" ::= { extremeWirelessRemoteConnectBindingEntry 7} extremeWirelessRemoteConnectBindingEnabled OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "An entry in this table can be created but left as disabled. If you set this variable to True then the RemoteConnect controller will consider this binding when trying to map APs to RemoteConnect ports. Else, it will ignore it." ::= {extremeWirelessRemoteConnectBindingEntry 8} extremeWirelessRemoteConnectBindingBound OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "Specifies if an AP has come up and has been matched to this binding. If this is true, then the extremeWirelessPortStatus table will have an entry for this RemoteConnect port." ::= {extremeWirelessRemoteConnectBindingEntry 9} extremeWirelessRemoteConnectBindingRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "RowStatus attribute. When this row is deleted, the binding goes away" ::= {extremeWirelessRemoteConnectBindingEntry 10} -- *************************************************************************************** -- This table specifies how the controller should choose to redirect certain APs to other -- controllers -- *************************************************************************************** extremeWirelessRemoteConnectRedirectBindingTable OBJECT-TYPE SYNTAX SEQUENCE OF ExtremeWirelessRemoteConnectRedirectBindingEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table specifies the RemoteConnect redirection configuration for various ports." ::= { extremeProfile 8 } extremeWirelessRemoteConnectRedirectBindingEntry OBJECT-TYPE SYNTAX ExtremeWirelessRemoteConnectRedirectBindingEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION " " INDEX { extremeWirelessRemoteConnectRedirectBindingIndex } ::= { extremeWirelessRemoteConnectRedirectBindingTable 1 } ExtremeWirelessRemoteConnectRedirectBindingEntry ::= SEQUENCE { extremeWirelessRemoteConnectRedirectBindingIndex INTEGER, extremeWirelessRemoteConnectRedirectBindingType WirelessRemoteConnectBindingType, extremeWirelessRemoteConnectRedirectBindingMAC MacAddress, extremeWirelessRemoteConnectRedirectBindingSerial OCTET STRING, extremeWirelessRemoteConnectRedirectBindingIPAddressType InetAddressType, extremeWirelessRemoteConnectRedirectBindingIPAddress InetAddress, extremeWirelessRemoteConnectRedirectBindAttachSwitchIPAddrType InetAddressType, extremeWirelessRemoteConnectRedirectBindAttachSwitchIPAddr InetAddress, extremeWirelessRemoteConnectRedirectBindingEnabled TruthValue, extremeWirelessRemoteConnectRedirectBindingNumRedirects Counter32, extremeWirelessRemoteConnectRedirectBindingRowStatus RowStatus} extremeWirelessRemoteConnectRedirectBindingIndex OBJECT-TYPE SYNTAX INTEGER(1..255) MAX-ACCESS not-accessible STATUS current DESCRIPTION "The index of this RedirectBinding." ::= { extremeWirelessRemoteConnectRedirectBindingEntry 1} extremeWirelessRemoteConnectRedirectBindingType OBJECT-TYPE SYNTAX WirelessRemoteConnectBindingType MAX-ACCESS read-create STATUS current DESCRIPTION "This is the type of RedirectBinding. Based on this, one of the following columns will be valid." ::= { extremeWirelessRemoteConnectRedirectBindingEntry 2 } extremeWirelessRemoteConnectRedirectBindingMAC OBJECT-TYPE SYNTAX MacAddress MAX-ACCESS read-create STATUS current DESCRIPTION "The MAC address of the AP that will be redirected. This is valid only if the extremeWirelessRemoteConnectRedirectBindingType is set to mac-address" ::= { extremeWirelessRemoteConnectRedirectBindingEntry 3} extremeWirelessRemoteConnectRedirectBindingSerial OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-create STATUS current DESCRIPTION "The serial number of the AP that is bound to this virtual port. This is valid only if the extremeWirelessRemoteConnectRedirectBindingType is set to serial-number" ::= { extremeWirelessRemoteConnectRedirectBindingEntry 4} extremeWirelessRemoteConnectRedirectBindingIPAddressType OBJECT-TYPE SYNTAX InetAddressType MAX-ACCESS read-create STATUS current DESCRIPTION "The IP address type of the AP that will be redirected. This is valid only if the extremeWirelessRemoteConnectRedirectBindingType is set to ip-address" ::= { extremeWirelessRemoteConnectRedirectBindingEntry 5} extremeWirelessRemoteConnectRedirectBindingIPAddress OBJECT-TYPE SYNTAX InetAddress MAX-ACCESS read-create STATUS current DESCRIPTION "The IP address of the AP that will be redirected. This is valid only if the extremeWirelessRemoteConnectRedirectBindingType is set to ip-address" ::= { extremeWirelessRemoteConnectRedirectBindingEntry 6} extremeWirelessRemoteConnectRedirectBindAttachSwitchIPAddrType OBJECT-TYPE SYNTAX InetAddressType MAX-ACCESS read-create STATUS current DESCRIPTION "The IP address type of the slave " ::= { extremeWirelessRemoteConnectRedirectBindingEntry 7} extremeWirelessRemoteConnectRedirectBindAttachSwitchIPAddr OBJECT-TYPE SYNTAX InetAddress MAX-ACCESS read-create STATUS current DESCRIPTION "The IP address of the slave" ::= { extremeWirelessRemoteConnectRedirectBindingEntry 8} extremeWirelessRemoteConnectRedirectBindingEnabled OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "An entry in this table can be created but left as disabled. If you set this variable to True then the RemoteConnect controller will consider this RedirectBinding when trying to redirect APs. Else, it will ignore it." ::= {extremeWirelessRemoteConnectRedirectBindingEntry 9} extremeWirelessRemoteConnectRedirectBindingNumRedirects OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of times this redirect has been invoked." ::= {extremeWirelessRemoteConnectRedirectBindingEntry 10} extremeWirelessRemoteConnectRedirectBindingRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-write STATUS current DESCRIPTION "Standard row status semantics." ::= {extremeWirelessRemoteConnectRedirectBindingEntry 11} -- *************************************************************************************** -- This table specifies the list of APs that could not be bound or redirected due to -- a lack of mapping on this controller -- *************************************************************************************** extremeWirelessRemoteConnectDeviceDBGroup OBJECT IDENTIFIER ::= { extremeProfile 9 } extremeWirelessRemoteConnectDeviceDBTimeOut OBJECT-TYPE SYNTAX INTEGER (0 | 30..3600) MAX-ACCESS read-write STATUS current DESCRIPTION "Timeout value for unbound APs entry in seconds. 0 for disable" ::= { extremeWirelessRemoteConnectDeviceDBGroup 1 } extremeWirelessRemoteConnectUnboundAPsTable OBJECT-TYPE SYNTAX SEQUENCE OF ExtremeWirelessRemoteConnectUnboundAPsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains the list of APs that could not be bound or redirected." ::= { extremeProfile 10 } extremeWirelessRemoteConnectUnboundAPsEntry OBJECT-TYPE SYNTAX ExtremeWirelessRemoteConnectUnboundAPsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION " " INDEX { extremeWirelessRemoteConnectUnboundAPsIndex } ::= { extremeWirelessRemoteConnectUnboundAPsTable 1 } ExtremeWirelessRemoteConnectUnboundAPsEntry ::= SEQUENCE { extremeWirelessRemoteConnectUnboundAPsIndex INTEGER, extremeWirelessRemoteConnectUnboundAPsMAC MacAddress, extremeWirelessRemoteConnectUnboundAPsSerial OCTET STRING, extremeWirelessRemoteConnectUnboundAPsIPAddressType InetAddressType, extremeWirelessRemoteConnectUnboundAPsIPAddress InetAddress, extremeWirelessRemoteConnectUnboundAPsNumAttempts Counter32, extremeWirelessRemoteConnectUnboundAPsRowStatus RowStatus} extremeWirelessRemoteConnectUnboundAPsIndex OBJECT-TYPE SYNTAX INTEGER(0..65535) MAX-ACCESS not-accessible STATUS current DESCRIPTION "The index of this table." ::= { extremeWirelessRemoteConnectUnboundAPsEntry 1} extremeWirelessRemoteConnectUnboundAPsMAC OBJECT-TYPE SYNTAX MacAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The MAC address of the unbound AP." ::= { extremeWirelessRemoteConnectUnboundAPsEntry 2} extremeWirelessRemoteConnectUnboundAPsSerial OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-only STATUS current DESCRIPTION "The serial number of the unbound AP" ::= { extremeWirelessRemoteConnectUnboundAPsEntry 3} extremeWirelessRemoteConnectUnboundAPsIPAddressType OBJECT-TYPE SYNTAX InetAddressType MAX-ACCESS read-only STATUS current DESCRIPTION "The IP address type of the unbound AP" ::= { extremeWirelessRemoteConnectUnboundAPsEntry 4} extremeWirelessRemoteConnectUnboundAPsIPAddress OBJECT-TYPE SYNTAX InetAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The IP address of the unbound AP" ::= { extremeWirelessRemoteConnectUnboundAPsEntry 5} extremeWirelessRemoteConnectUnboundAPsNumAttempts OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of times this AP contacted this controller." ::= {extremeWirelessRemoteConnectUnboundAPsEntry 6} extremeWirelessRemoteConnectUnboundAPsRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "Standard row status semantics. Only valid value to set is destroy (6)." ::= {extremeWirelessRemoteConnectUnboundAPsEntry 7} -- *************************************************************** -- -- RADIUS Server Configuration -- -- The Radius Server Table on the Ethernet switch is implemented -- -- using the extremeAuthServerTable, defines under extremeServices -- -- -- -- The extremeAPAuthServerTable is implemented per wireless port. -- -- Each AP will have to implement this table to allow the LAC to -- -- propogate configuration information. -- -- *************************************************************** -- extremeAPAuthServerTable OBJECT-TYPE SYNTAX SEQUENCE OF ExtremeAPAuthServerEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table is proxied by the wireless APs. It allows the wireless concentrator to configure the APs security settings." ::= { extremeAP 12 } extremeAPAuthServerEntry OBJECT-TYPE SYNTAX ExtremeAPAuthServerEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION " " INDEX { extremeWirelessPortIfIndex, extremeAPAuthServerIndex } ::= { extremeAPAuthServerTable 1 } ExtremeAPAuthServerEntry ::= SEQUENCE { extremeAPAuthServerIndex INTEGER, extremeAPAuthServerAddressType InetAddressType, extremeAPAuthServerAddress InetAddress, extremeAPAuthServerPort INTEGER, extremeAPAuthServerSecret OCTET STRING, extremeAPAuthServerReTransmit INTEGER, extremeAPAuthServerStatus TruthValue} extremeAPAuthServerIndex OBJECT-TYPE SYNTAX INTEGER (1..2) MAX-ACCESS not-accessible STATUS current DESCRIPTION "Integer representing either primary (1) or backup (2) server." ::= { extremeAPAuthServerEntry 1 } extremeAPAuthServerAddressType OBJECT-TYPE SYNTAX InetAddressType MAX-ACCESS read-only STATUS current DESCRIPTION "The type of address specified in the object 'extremeAuthServerAddress'. Currently, only 'ipv4' and 'dns' are supported." DEFVAL { ipv4 } ::= { extremeAPAuthServerEntry 2 } extremeAPAuthServerAddress OBJECT-TYPE SYNTAX InetAddress MAX-ACCESS read-write STATUS current DESCRIPTION "IP address of the radius server. The act of assigning an IP address enables the client to use the server. Setting this value to 0.0.0.0 disables this entry." ::= { extremeAPAuthServerEntry 3 } extremeAPAuthServerPort OBJECT-TYPE SYNTAX INTEGER (0..65535) MAX-ACCESS read-only STATUS current DESCRIPTION "The UDP port number of the remote syslog server to which syslog messages will be sent." ::= { extremeAPAuthServerEntry 4 } extremeAPAuthServerSecret OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-write STATUS current DESCRIPTION "This is the shared secret between the Authenticator and radius server. This is logically write-only." ::= { extremeAPAuthServerEntry 5 } extremeAPAuthServerReTransmit OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION "This is the timeout in seconds after which the Authenticator will re transmit requests to the radius server." ::= { extremeAPAuthServerEntry 6 } extremeAPAuthServerStatus OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "Specifies whether the DNS entry is in use or not" ::= { extremeAPAuthServerEntry 7 } -- *************************************************************** -- -- Scan Configuration Table : This table provides the ability to -- -- configure the parameters associated with ON-Channel scanning -- -- for other access points. -- -- *************************************************************** -- extremeWirelessScanCfgTable OBJECT-TYPE SYNTAX SEQUENCE OF ExtremeWirelessScanCfgEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains one entry per wireless interface. It allows for configuration of active and passive scan parameters." ::= { extremeAP 24 } extremeWirelessScanCfgEntry OBJECT-TYPE SYNTAX ExtremeWirelessScanCfgEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "" INDEX { ifIndex } ::= { extremeWirelessScanCfgTable 1 } ExtremeWirelessScanCfgEntry ::= SEQUENCE { extremeWirelessScanEnable TruthValue, extremeWirelessScanSendProbe TruthValue, extremeWirelessScanProbeInterval Unsigned32, extremeWirelessScanResultTableSize Unsigned32, extremeWirelessScanResultTimeout Unsigned32, extremeWirelessScanResetStats TruthValue, extremeWirelessScanClearTable TruthValue, extremeWirelessScanSendAPAddedTrap TruthValue, extremeWirelessScanSendAPRemovedTrap TruthValue, extremeWirelessScanSendAPUpdatedTrap TruthValue } extremeWirelessScanEnable OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "By setting this to true the wireless interface will collect information from beacons and (possible) probe responses. If this value is set to false this information will not be collected." DEFVAL { true } ::= { extremeWirelessScanCfgEntry 1 } extremeWirelessScanSendProbe OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "If this value is set to TRUE the wireless interface will send probe requests to the broadcast SSID every ProbeInterval. The results of these probes will be recorded in the scan results table. If this is false, the AP will only collect information from beacon frames." DEFVAL { false } ::= { extremeWirelessScanCfgEntry 2 } extremeWirelessScanProbeInterval OBJECT-TYPE SYNTAX Unsigned32 UNITS "milliseconds" MAX-ACCESS read-write STATUS current DESCRIPTION "This allows for the configuration of the interval over which probe requests will be sent." DEFVAL { 100 } ::= { extremeWirelessScanCfgEntry 3 } extremeWirelessScanResultTableSize OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-write STATUS current DESCRIPTION "This parameter permits the configuration of the result table size. If there are more entries discovered than there are room for the new entry will replace the oldest entry in the table. In this case a new entry trap will be sent with the OverFlow value set to TRUE." DEFVAL { 1024 } ::= { extremeWirelessScanCfgEntry 4 } extremeWirelessScanResultTimeout OBJECT-TYPE SYNTAX Unsigned32 UNITS "seconds" MAX-ACCESS read-write STATUS current DESCRIPTION "By default the scan result table will age out entries which haven't been updated for some time. When an entry is aged out of the table a scanResultAgeOut trap is generated. Setting this value to 0 will disable the aging out of entries." DEFVAL { 3600 } ::= { extremeWirelessScanCfgEntry 5 } extremeWirelessScanResetStats OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "Setting this to TRUE will cause the scan module to reset its internal statistics, as well as the packet counts for each entry in the scan results table. It will *not* remove any entries in the scan table." ::= { extremeWirelessScanCfgEntry 6 } extremeWirelessScanClearTable OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "Setting this to TRUE will cause the scan module to reset its internal table. All currently detected stations will be removed. Scan statistics (i.e. watermark) will not be reset." ::= { extremeWirelessScanCfgEntry 7 } extremeWirelessScanSendAPAddedTrap OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "Setting this to TRUE will cause the scan module to send a trap whenever a new entry is added to the scan results table. If this value is false the scan module will suppress the trap." DEFVAL { true } ::= { extremeWirelessScanCfgEntry 8 } extremeWirelessScanSendAPRemovedTrap OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "Setting this to TRUE will cause the scan module to send a trap whenever an entry is removed from the scan results table." DEFVAL { true } ::= { extremeWirelessScanCfgEntry 9 } extremeWirelessScanSendAPUpdatedTrap OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "Setting this to TRUE will cause the scan module to send a trap whenever an entry is updated in the scan results table. This will happen if the list of IEs sent from a particular MAC address changes." DEFVAL { true } ::= { extremeWirelessScanCfgEntry 10 } -- *************************************************************** -- -- Off-Channel AP Scan : This table provides the ability to confi -- -- ure and start an off-channel scan for other APs. -- -- *************************************************************** -- extremeWirelessOffChannelScanCfgTable OBJECT-TYPE SYNTAX SEQUENCE OF ExtremeWirelessOffChannelScanCfgEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains one entry per wireless interface. It allows for configuration of off-channel scan. To start an off-channel scan the management station should write values for channel list, min and max wait. Toggling the start value at this point will start an off-channel scan, unless one is already running. Results of the off-channel scan are reported to the scan results table together with the results of passive scan." ::= { extremeAP 25 } extremeWirelessOffChannelScanCfgEntry OBJECT-TYPE SYNTAX ExtremeWirelessOffChannelScanCfgEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "" INDEX { ifIndex } ::= { extremeWirelessOffChannelScanCfgTable 1 } ExtremeWirelessOffChannelScanCfgEntry ::= SEQUENCE { extremeWirelessOffChannelScanStart TruthValue, extremeWirelessOffChannelScanList BITS, extremeWirelessOffChannelScanMinWait Unsigned32, extremeWirelessOffChannelScanMaxWait Unsigned32, extremeWirelessOffChannelContinuous TruthValue } extremeWirelessOffChannelScanStart OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "Setting this to TRUE will cause the scan module to start an off-channel scan. The radio will be disabled for the duration of the scan. The scan module will change to each of the specified channels in order. It will then conduct passive (and perhaps active) scans on that channel for the configured intervals. When the scan is finished the radio will be re-enabled. The scan will wait on each channel for at least MinWait milliseconds even if it sees no traffic on the channel. It will wait for at most MaxWait msecs even if it sees traffic. As a result the best case time for the scan is given by: # Of Channels * extremeWirelessOffChannelScanMinWait The worst case completion time is given by: # Of Channels * extremeWirelessOffChannelScanMaxWait Results of the off-channnel scan a reported to the scan results table." ::= { extremeWirelessOffChannelScanCfgEntry 1 } extremeWirelessOffChannelScanList OBJECT-TYPE SYNTAX BITS { scanAll(0), scanEvery(1), scanChannel1(2), scanChannel2(3), scanChannel3(4), scanChannel4(5), scanChannel5(6), scanChannel6(7), scanChannel7(8), scanChannel8(9), scanChannel9(10), scanChannel10(11), scanChannel11(12), scanChannel12(13), scanChannel13(14), scanChannel14(15), scanChannel34(16), scanChannel36(17), scanChannel40(18), scanChannel44(19), scanChannel48(20), scanChannel52(21), scanChannel56(22), scanChannel60(23), scanChannel64(24), scanChannel100(25), scanChannel104(26), scanChannel108(27), scanChannel113(28), scanChannel116(29), scanChannel120(30), scanChannel124(31), scanChannel128(32), scanChannel132(33), scanChannel140(34), scanChannel149(35), scanChannel153(36), scanChannel157(37), scanChannel161(38), scanChannel165(39) } MAX-ACCESS read-write STATUS current DESCRIPTION "This value controls the channels which will be scanned during the off-channel scan. Two special values should be noted: all - causes the radio to scan all channels supported by the configured country code. While on each channel the radio will send out probe requests if the value of extremeWirelessScanSendProbeRequest is true. every - causes the radio to scan all channels, even those which are restricted by the country code. The radio will only send probe request on channels that are legal for that country code." ::= { extremeWirelessOffChannelScanCfgEntry 2 } extremeWirelessOffChannelScanMinWait OBJECT-TYPE SYNTAX Unsigned32 UNITS "milliseconds" MAX-ACCESS read-write STATUS current DESCRIPTION "This value controls the minimum time the off-channel scan will wait on a particular channel if it doesn't see any traffic." DEFVAL { 1 } ::= { extremeWirelessOffChannelScanCfgEntry 3 } extremeWirelessOffChannelScanMaxWait OBJECT-TYPE SYNTAX Unsigned32 UNITS "milliseconds" MAX-ACCESS read-write STATUS current DESCRIPTION "This value controls the maximum time the off-channel scan will wait on a particular channel even if it is receiving beacons etc." DEFVAL { 10 } ::= { extremeWirelessOffChannelScanCfgEntry 4 } extremeWirelessOffChannelContinuous OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "Setting this value to true results in the off-channel scan looping on the configured values until the channel scan is disabled." DEFVAL { false } ::= { extremeWirelessOffChannelScanCfgEntry 5 } -- *************************************************************** -- -- Scan Status Table : This table contains information about the -- -- current status of the scan feature. -- -- *************************************************************** -- extremeWirelessScanStatusTable OBJECT-TYPE SYNTAX SEQUENCE OF ExtremeWirelessScanStatusEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains one entry per wireless interface. It provides status and statistics information for the scan feature operating on that wireless interface." ::= { extremeAP 26 } extremeWirelessScanStatusEntry OBJECT-TYPE SYNTAX ExtremeWirelessScanStatusEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "" INDEX { ifIndex } ::= { extremeWirelessScanStatusTable 1 } ExtremeWirelessScanStatusEntry ::= SEQUENCE { extremeWirelessScanCurrentTableSize Unsigned32, extremeWirelessScanTableWatermark Unsigned32, extremeWirelessScanTotalOverflows Unsigned32, extremeWirelessScanTotalTimeouts Unsigned32, extremeWirelessScanOffChannelRunning TruthValue, extremeWirelessScanCurrentChannel Unsigned32, extremeWirelessScanLastElement TimeTicks, extremeWirelessScanNumProbes Unsigned32 } extremeWirelessScanCurrentTableSize OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This indicates the current number of entries in the scan results table." ::= { extremeWirelessScanStatusEntry 1 } extremeWirelessScanTableWatermark OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This indicates the largest size the results table has reached since the status values have been reset, or the system has booted." ::= { extremeWirelessScanStatusEntry 2 } extremeWirelessScanTotalOverflows OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This gives the total number of entries which have been removed to make room for a newer entry. This should be equal to the number of AP added traps the system has generated with the overflow value set to true." ::= { extremeWirelessScanStatusEntry 3 } extremeWirelessScanTotalTimeouts OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This gives the total number of entries which have been removed because they have become stale. This should be equal to the number of AP removed traps sent by the system." ::= { extremeWirelessScanStatusEntry 4 } extremeWirelessScanOffChannelRunning OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION "If this value is true it indicates that an off-channel scan is currently running. This implies that the radio is current disabled." ::= { extremeWirelessScanStatusEntry 5 } extremeWirelessScanCurrentChannel OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "If the value of extremeWirelessScanOffChannelRunning is true this variable give the value of the current channel the AP is scanning on. If a scan is not running, the value of this variable is undefined." ::= { extremeWirelessScanStatusEntry 6 } extremeWirelessScanLastElement OBJECT-TYPE SYNTAX TimeTicks MAX-ACCESS read-only STATUS current DESCRIPTION "This gives the sysUpTime when the last new station was inserted in the results table." ::= { extremeWirelessScanStatusEntry 7 } extremeWirelessScanNumProbes OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This gives the number of probe requests sent by this wireless interface." ::= { extremeWirelessScanStatusEntry 8 } -- *************************************************************** -- -- Scan Results Table : This table provides information collected -- -- during on and off-channel scans about the APs discovered. -- -- *************************************************************** -- extremeWirelessScanResultsTable OBJECT-TYPE SYNTAX SEQUENCE OF ExtremeWirelessScanResultsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains one entry per wireless interface. It provides status and statistics information for the scan feature operating on that wireless interface." ::= { extremeAP 27 } extremeWirelessScanResultsEntry OBJECT-TYPE SYNTAX ExtremeWirelessScanResultsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "" INDEX { ifIndex, extremeWirelessScanResultsStationId } ::= { extremeWirelessScanResultsTable 1 } ExtremeWirelessScanResultsEntry ::= SEQUENCE { extremeWirelessScanResultsStationId MacAddress, extremeWirelessScanResultsFirstSeen TimeTicks, extremeWirelessScanResultsLastChange TimeTicks, extremeWirelessScanResultsPacketTime INTEGER, extremeWirelessScanResultsPacketRate INTEGER, extremeWirelessScanResultsChannel INTEGER, extremeWirelessScanResultsMinRSS INTEGER, extremeWirelessScanResultsMaxRSS INTEGER, extremeWirelessScanResultsAvgRSS INTEGER, extremeWirelessScanResultsTotalBeacons Unsigned32, extremeWirelessScanResultsTotalProbes Unsigned32, extremeWirelessScanResultsDiscoveredBy INTEGER, extremeWirelessScanResultsDSSOFDM TruthValue, extremeWirelessScanResultsRSNEnabled TruthValue, extremeWirelessScanResultsGShortSlot TruthValue, extremeWirelessScanResultsChannelAgility TruthValue, extremeWirelessScanResultsPBCC TruthValue, extremeWirelessScanResultsPreamble TruthValue, extremeWirelessScanResultsPrivacy TruthValue, extremeWirelessScanResultsCFPollReq TruthValue, extremeWirelessScanResultsCFPollable TruthValue, extremeWirelessScanResultsNetworkType INTEGER, extremeWirelessScanResultsSSID OCTET STRING, extremeWirelessScanResultsRateSet OCTET STRING, extremeWirelessScanResultsExtRateSet OCTET STRING, extremeWirelessScanResultsDSSParameter INTEGER, extremeWirelessScanResultsTIMCount INTEGER, extremeWirelessScanResultsTIMPeriod INTEGER, extremeWirelessScanResultsTIMTrafficInd TruthValue, extremeWirelessScanResultsCountryCode OCTET STRING, extremeWirelessScanWPAIEPresent TruthValue, extremeWirelessScanWPAVersion Unsigned32, extremeWirelessScanWPAIEMcastCipher WPACipherSet, extremeWirelessScanWPAUcastCipherCount Unsigned32, extremeWirelessScanWPAUcastCipher WPACipherSet, extremeWirelessScanWPAKeyMgmtCount Unsigned32, extremeWirelessScanWPAKeyMgmtSuite WPAKeyMgmtSet, extremeWirelessScanResultsIEBlob OCTET STRING } extremeWirelessScanResultsStationId OBJECT-TYPE SYNTAX MacAddress MAX-ACCESS read-only STATUS current DESCRIPTION "This is the MAC address of the detected station." ::= { extremeWirelessScanResultsEntry 1 } extremeWirelessScanResultsFirstSeen OBJECT-TYPE SYNTAX TimeTicks MAX-ACCESS read-only STATUS current DESCRIPTION "This gives the sysUpTime when this station entry was created." ::= { extremeWirelessScanResultsEntry 2 } extremeWirelessScanResultsLastChange OBJECT-TYPE SYNTAX TimeTicks MAX-ACCESS read-only STATUS current DESCRIPTION "This gives the sysUpTime of the station entry the last time it was updated (i.e. a beacon etc was received)." ::= { extremeWirelessScanResultsEntry 3 } extremeWirelessScanResultsPacketTime OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "This gives the timestamp field from the last beacon/probe response received from this station." ::= { extremeWirelessScanResultsEntry 4 } extremeWirelessScanResultsPacketRate OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "This gives the rate at which the last packet was sent by the station. TODO: What are the units here on rate?" ::= { extremeWirelessScanResultsEntry 5 } extremeWirelessScanResultsChannel OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "This gives the channel the last packet received by this station was recieved on." ::= { extremeWirelessScanResultsEntry 6 } extremeWirelessScanResultsMinRSS OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "This is the smallest RSS value of any packet recieved from this station." ::= { extremeWirelessScanResultsEntry 7 } extremeWirelessScanResultsMaxRSS OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "This is the largest RSS value of any packet recieved from this station." ::= { extremeWirelessScanResultsEntry 8 } extremeWirelessScanResultsAvgRSS OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "This is a running average of RSS values of all the packets received from this station." ::= { extremeWirelessScanResultsEntry 9 } extremeWirelessScanResultsTotalBeacons OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This counter gives the total number of beacons received from this station." ::= { extremeWirelessScanResultsEntry 10 } extremeWirelessScanResultsTotalProbes OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This counter gives the total number of probe responses received from this station." ::= { extremeWirelessScanResultsEntry 11 } extremeWirelessScanResultsDiscoveredBy OBJECT-TYPE SYNTAX INTEGER { probe (1), beacon (2) } MAX-ACCESS read-only STATUS current DESCRIPTION "This gives the type of packet which cause this results entry to be created." ::= { extremeWirelessScanResultsEntry 12 } extremeWirelessScanResultsDSSOFDM OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION "TODO : What is this?" ::= { extremeWirelessScanResultsEntry 13 } extremeWirelessScanResultsRSNEnabled OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates if RSN capabilities are enabled on the sending station." ::= { extremeWirelessScanResultsEntry 14 } extremeWirelessScanResultsGShortSlot OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION "TODO : What is this?" ::= { extremeWirelessScanResultsEntry 15 } extremeWirelessScanResultsChannelAgility OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION "TODO : What is this?" ::= { extremeWirelessScanResultsEntry 16 } extremeWirelessScanResultsPBCC OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION "TODO : What is this?" ::= { extremeWirelessScanResultsEntry 17 } extremeWirelessScanResultsPreamble OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION "TODO : What is this?" ::= { extremeWirelessScanResultsEntry 18 } extremeWirelessScanResultsPrivacy OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION "This is true if MAC-based privacy is invoked on the sending station." ::= { extremeWirelessScanResultsEntry 19 } extremeWirelessScanResultsCFPollReq OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION "TODO: What is this?" ::= { extremeWirelessScanResultsEntry 20 } extremeWirelessScanResultsCFPollable OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION "TODO: What is this?" ::= { extremeWirelessScanResultsEntry 21 } extremeWirelessScanResultsNetworkType OBJECT-TYPE SYNTAX INTEGER { ibss (1), bss (2) } MAX-ACCESS read-only STATUS current DESCRIPTION "This indicates what type of network it is. If this value is IBSS the last beacon/probe response was sent by a host operating in ad-hoc mode." ::= { extremeWirelessScanResultsEntry 22 } extremeWirelessScanResultsSSID OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-only STATUS current DESCRIPTION "This provides the value of the SSID value as is was recieved in the beacon or probe response. If no SSID was sent in the probe this value is NULL." ::= { extremeWirelessScanResultsEntry 23 } extremeWirelessScanResultsRateSet OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-only STATUS current DESCRIPTION "This provides the value of the rate set IE as it was received in the beacon or probe response. If no rate set was recieved then this value is NULL." ::= { extremeWirelessScanResultsEntry 24 } extremeWirelessScanResultsExtRateSet OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-only STATUS current DESCRIPTION "This provides the value of the extended rate set IE as it was received in the beacon or probe response. If no rate set was recieved then this value is NULL." ::= { extremeWirelessScanResultsEntry 25 } extremeWirelessScanResultsDSSParameter OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "Provides the value of the DSS parameter IE, which is the channel." ::= { extremeWirelessScanResultsEntry 26 } extremeWirelessScanResultsTIMCount OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "TODO: What is this?" ::= { extremeWirelessScanResultsEntry 27 } extremeWirelessScanResultsTIMPeriod OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "TODO: What is this?" ::= { extremeWirelessScanResultsEntry 28 } extremeWirelessScanResultsTIMTrafficInd OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION "TODO: What is this?" ::= { extremeWirelessScanResultsEntry 29 } extremeWirelessScanResultsCountryCode OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-only STATUS current DESCRIPTION "Value of country code supplied by the IE" ::= { extremeWirelessScanResultsEntry 30 } extremeWirelessScanWPAIEPresent OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION "If this value is true it indicates that WPA information was gathered from this AP in the last beacon. It implies that the WPA variables below are valid. If this value is false it indicates that this AP did not send a WPA IE in its last beacon, and the values below are meaningless." ::= { extremeWirelessScanResultsEntry 31 } extremeWirelessScanWPAVersion OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This value gives the version of WPA supported by this AP. See IEEE 802.11i Draft 3.0 section 7 for meaning of various values." ::= { extremeWirelessScanResultsEntry 32 } extremeWirelessScanWPAIEMcastCipher OBJECT-TYPE SYNTAX WPACipherSet MAX-ACCESS read-only STATUS current DESCRIPTION "This value gives the single multicast cipher supported by this AP." ::= { extremeWirelessScanResultsEntry 33 } extremeWirelessScanWPAUcastCipherCount OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This value gives the total number of unicast ciphers supported by this AP. It corresponds to the number of bits set in the extremeWirelessScanWPAUcastCipher variable." ::= { extremeWirelessScanResultsEntry 34 } extremeWirelessScanWPAUcastCipher OBJECT-TYPE SYNTAX WPACipherSet MAX-ACCESS read-only STATUS current DESCRIPTION "This gives the list of cipher suites which are supported by this AP." ::= { extremeWirelessScanResultsEntry 35 } extremeWirelessScanWPAKeyMgmtCount OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This gives the number of key-management schemes supported by this AP. It corresponds to the number of bits set in the extremeWirelessScanWPAKeyMgmtSuite variable." ::= { extremeWirelessScanResultsEntry 36 } extremeWirelessScanWPAKeyMgmtSuite OBJECT-TYPE SYNTAX WPAKeyMgmtSet MAX-ACCESS read-only STATUS current DESCRIPTION "This indicates the supported key-management suites supported by this AP." ::= { extremeWirelessScanResultsEntry 37 } extremeWirelessScanResultsIEBlob OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-only STATUS current DESCRIPTION "All the IEs received in the last packet encoded as a blob of Type, Length, Value tuples." ::= { extremeWirelessScanResultsEntry 38 } -- *************************************************************** -- -- Probe Info Configuration Table : This table allows for config -- -- for the collection of probe request packets. The AP uses this -- -- to populate the client information tables. -- -- *************************************************************** -- extremeWirelessProbeInfoCfgTable OBJECT-TYPE SYNTAX SEQUENCE OF ExtremeWirelessProbeInfoCfgEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains one entry per physical and virtual interface. It controls the collection of client information via PROBE REQ packets." ::= { extremeAP 28 } extremeWirelessProbeInfoCfgEntry OBJECT-TYPE SYNTAX ExtremeWirelessProbeInfoCfgEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Note that the ifIndex here can be either a physical or virtual wireless interface index." INDEX { ifIndex } ::= { extremeWirelessProbeInfoCfgTable 1 } ExtremeWirelessProbeInfoCfgEntry ::= SEQUENCE { extremeWirelessProbeInfoEnable TruthValue, extremeWirelessProbeInfoKeepIEs TruthValue, extremeWirelessProbeInfoTableSize Unsigned32, extremeWirelessProbeInfoTimeout Unsigned32, extremeWirelessProbeInfoTableClear TruthValue, extremeWirelessProbeInfoSourceClear MacAddress, extremeWirelessProbeInfoTableStatsClear TruthValue, extremeWirelessProbeInfoSourceStatsClear MacAddress, extremeWirelessProbeInfoSendAddedTrap TruthValue, extremeWirelessProbeInfoSendRemovedTrap TruthValue } extremeWirelessProbeInfoEnable OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "If this is set to TRUE then this virtual or physical interface will register with the MAC layer to receive notification of PROBE REQ packets. In the case of a virtual interface this implies the receipt of directed PROBE REQ packets. If set to FALSE no PROBE REQ packets will be received, and current entries will eventually timeout." DEFVAL { true } ::= { extremeWirelessProbeInfoCfgEntry 1 } extremeWirelessProbeInfoKeepIEs OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "If this value is set to TRUE then the rate IE which is carried in the PROBE REQ packet will be recorded. If FALSE, no rate information will be kept." DEFVAL { false } ::= { extremeWirelessProbeInfoCfgEntry 2 } extremeWirelessProbeInfoTableSize OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-write STATUS current DESCRIPTION "This value sets the maximum size of the probe info results table, which limits the number of clients this AP can record PROBE REQ information from." DEFVAL { 128 } ::= { extremeWirelessProbeInfoCfgEntry 3 } extremeWirelessProbeInfoTimeout OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-write STATUS current DESCRIPTION "This is the timeout, in seconds, for an entry in the probe info table. Once a PROBE REQ has not been heard from a client in this time period, it's entry is removed. The value 0 is a sentinel, indicating no timeout." DEFVAL { 3600 } ::= { extremeWirelessProbeInfoCfgEntry 4 } extremeWirelessProbeInfoTableClear OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "Setting this value to TRUE causes all entries in the probe info table to be removed. Reading this value has no meaning." ::= { extremeWirelessProbeInfoCfgEntry 5 } extremeWirelessProbeInfoSourceClear OBJECT-TYPE SYNTAX MacAddress MAX-ACCESS read-write STATUS current DESCRIPTION "Setting this to the value of some MAC address results in any matching MAC address in the probe info table being removed. Reading this value has no meaning." ::= { extremeWirelessProbeInfoCfgEntry 6 } extremeWirelessProbeInfoTableStatsClear OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "Setting this to TRUE results in all historical statistics in the probe info table being set to 0. No entries will be removed. Reading this has no meaning." ::= { extremeWirelessProbeInfoCfgEntry 7 } extremeWirelessProbeInfoSourceStatsClear OBJECT-TYPE SYNTAX MacAddress MAX-ACCESS read-write STATUS current DESCRIPTION "Setting this to a MAC address will clear the historical stats associated with the matching MAC address in the probe info table. Reading this has no meaning." ::= { extremeWirelessProbeInfoCfgEntry 8 } extremeWirelessProbeInfoSendAddedTrap OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "Setting this to TRUE will cause the management module to send a trap whenever a new PROBE REQ source is added to the probe info table. Setting this to FALSE will suppress the trap." DEFVAL { false } ::= { extremeWirelessProbeInfoCfgEntry 9 } extremeWirelessProbeInfoSendRemovedTrap OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "Setting this to TRUE will cause the management module to send a trap whenever a PROBE REQ source is removed from the probe info table. Setting this to false will suppress the trap." DEFVAL { false } ::= { extremeWirelessProbeInfoCfgEntry 10 } -- *************************************************************** -- -- Probe Info Status Table : This table gives current status of -- -- the probe request storage feature. -- -- *************************************************************** -- extremeWirelessProbeInfoStatusTable OBJECT-TYPE SYNTAX SEQUENCE OF ExtremeWirelessProbeInfoStatusEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains one entry per physical and virtual interface. It gives debugging and status information for the operation of the probe info feature on that interface." ::= { extremeAP 29 } extremeWirelessProbeInfoStatusEntry OBJECT-TYPE SYNTAX ExtremeWirelessProbeInfoStatusEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Note that the ifIndex here can be either a physical or virtual wireless interface index." INDEX { ifIndex } ::= { extremeWirelessProbeInfoStatusTable 1 } ExtremeWirelessProbeInfoStatusEntry ::= SEQUENCE { extremeWirelessProbeInfoStatusCurrentTableSize Unsigned32, extremeWirelessProbeInfoStatusWatermark Unsigned32, extremeWirelessProbeInfoStatusTotalOverflows Unsigned32, extremeWirelessProbeInfoStatusTotalTimeouts Unsigned32, extremeWirelessProbeInfoStatusLastElement TimeTicks, extremeWirelessProbeInfoStatusTotalProbes Unsigned32 } extremeWirelessProbeInfoStatusCurrentTableSize OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This gives the current number of entries in the probe info table for this interface." ::= { extremeWirelessProbeInfoStatusEntry 1 } extremeWirelessProbeInfoStatusWatermark OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This is the maximum size the probe info table has been since the statistics have been reset." ::= { extremeWirelessProbeInfoStatusEntry 2 } extremeWirelessProbeInfoStatusTotalOverflows OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This gives the number of times an entry in the probe info table was overwritten because the table was full." ::= { extremeWirelessProbeInfoStatusEntry 3 } extremeWirelessProbeInfoStatusTotalTimeouts OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This gives the number of times an entry in the probe info table was timed out." ::= { extremeWirelessProbeInfoStatusEntry 4 } extremeWirelessProbeInfoStatusLastElement OBJECT-TYPE SYNTAX TimeTicks MAX-ACCESS read-only STATUS current DESCRIPTION "This gives the sysUpTime the last time an entry was added to the probe info table (or modified)." ::= { extremeWirelessProbeInfoStatusEntry 5 } extremeWirelessProbeInfoStatusTotalProbes OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This gives the total number of PROBE REQ packets that this interface has gotten." ::= { extremeWirelessProbeInfoStatusEntry 6 } -- *************************************************************** -- -- Probe Info Table : This table contains information on the probe -- -- request packets recieved from particular hosts. -- -- *************************************************************** -- extremeWirelessProbeInfoTable OBJECT-TYPE SYNTAX SEQUENCE OF ExtremeWirelessProbeInfoEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains one entry for each source MAC from which a PROBE REQ packet has been received. Entries are added when a packet is recieved from a new source mac. Entries are removed via management action, or by timeout or overflow." ::= { extremeAP 30 } extremeWirelessProbeInfoEntry OBJECT-TYPE SYNTAX ExtremeWirelessProbeInfoEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Note that the ifIndex here can be either a physical or virtual wireless interface index. In addition, this table is indexed by the MAC address of the PROBE REQ source." INDEX { ifIndex, extremeWirelessProbeInfoSource } ::= { extremeWirelessProbeInfoTable 1 } ExtremeWirelessProbeInfoEntry ::= SEQUENCE { extremeWirelessProbeInfoSource MacAddress, extremeWirelessProbeInfoTotalProbes Unsigned32, extremeWirelessProbeInfoTotalProbeResp Unsigned32, extremeWirelessProbeInfoRateIESize Unsigned32, extremeWirelessProbeInfoRateIE OCTET STRING, extremeWirelessProbeInfoFirstSeen TimeTicks, extremeWirelessProbeInfoLastChange TimeTicks, extremeWirelessProbeInfoLastRSS INTEGER, extremeWirelessProbeInfoLastRate INTEGER, extremeWirelessProbeInfoLastChannel INTEGER } extremeWirelessProbeInfoSource OBJECT-TYPE SYNTAX MacAddress MAX-ACCESS read-only STATUS current DESCRIPTION "This is the MAC address of the source which sent us the PROBE REQ packets described by this entry." ::= { extremeWirelessProbeInfoEntry 1 } extremeWirelessProbeInfoTotalProbes OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This gives the total number of PROBE REQ packets we have received from this source since the last time the stats were cleared." ::= { extremeWirelessProbeInfoEntry 2 } extremeWirelessProbeInfoTotalProbeResp OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This gives the total number of PROBE RESP packets we have sent to this source. This may not be equal to PROBE REQ based on rxmit, misses, etc." ::= { extremeWirelessProbeInfoEntry 3 } extremeWirelessProbeInfoRateIESize OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This gives the size of the rate-ie field in bytes. This may be 0, at which point there is no rate-ie." ::= { extremeWirelessProbeInfoEntry 4 } extremeWirelessProbeInfoRateIE OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-only STATUS current DESCRIPTION "This gives the rate IE as recieved in the last PROBE REQ packet. It is encoded as a TLV exactly as it was in the frame. This field may return NULL if storing of rate IE fields is disabled." ::= { extremeWirelessProbeInfoEntry 5 } extremeWirelessProbeInfoFirstSeen OBJECT-TYPE SYNTAX TimeTicks MAX-ACCESS read-only STATUS current DESCRIPTION "This gives the sysUpTime the first time a PROBE REQ was seen from this source." ::= { extremeWirelessProbeInfoEntry 6 } extremeWirelessProbeInfoLastChange OBJECT-TYPE SYNTAX TimeTicks MAX-ACCESS read-only STATUS current DESCRIPTION "This gives the sysUpTime the last time a PROBE REQ was seen from this source." ::= { extremeWirelessProbeInfoEntry 7 } extremeWirelessProbeInfoLastRSS OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "This gives the RSSI from the last PROBE REQ packet received from this station." ::= { extremeWirelessProbeInfoEntry 8 } extremeWirelessProbeInfoLastRate OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "This gives the rate at which the last packet was received from this station." ::= { extremeWirelessProbeInfoEntry 9 } extremeWirelessProbeInfoLastChannel OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "This gives the channel on which the last PROBE REQ from this station was heard. PROBE REQs may be heard during an off-channel scan, at which point this may not be equal to the current channel." ::= { extremeWirelessProbeInfoEntry 10 } -- *************************************************************** -- -- Per Client Historical Diagnostic Table : This table allows for -- -- configuration of diagnostic information collection. -- -- *************************************************************** -- extremeWirelessClientDiagCfgTable OBJECT-TYPE SYNTAX SEQUENCE OF ExtremeWirelessClientDiagCfgEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains one row per wireless interface. Each row contains configuration values for collection of per-client diagnostic information." ::= { extremeAP 31 } extremeWirelessClientDiagCfgEntry OBJECT-TYPE SYNTAX ExtremeWirelessClientDiagCfgEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "There is one entry in this table per virtual interface (SSID)." INDEX { ifIndex } ::= { extremeWirelessClientDiagCfgTable 1 } ExtremeWirelessClientDiagCfgEntry ::= SEQUENCE { extremeWirelessClientDiagCfgEnable TruthValue, extremeWirelessClientDiagCfgClearClient MacAddress, extremeWirelessClientDiagCfgTableSize Unsigned32, extremeWirelessClientDiagCfgTimeout Unsigned32 } extremeWirelessClientDiagCfgEnable OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "Setting this to TRUE enables the collection of historical information on this virtual interface. This implies that stations which send ASSOC or AUTH packets will have new entries created in the table for this interface." DEFVAL { true } ::= { extremeWirelessClientDiagCfgEntry 1 } extremeWirelessClientDiagCfgClearClient OBJECT-TYPE SYNTAX MacAddress MAX-ACCESS read-write STATUS current DESCRIPTION "Setting this to the MAC address of a client in the diag tables will clear the counters for that client. The entry will not be removed from the table, but all summation counters will be cleared." ::= { extremeWirelessClientDiagCfgEntry 2 } extremeWirelessClientDiagCfgTableSize OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-write STATUS current DESCRIPTION "This value will configure the maximum size of the diag table. The value is specified in number of entries. A value of 0 implies no upper limit." DEFVAL { 128 } ::= { extremeWirelessClientDiagCfgEntry 3 } extremeWirelessClientDiagCfgTimeout OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-write STATUS current DESCRIPTION "This value will configure the timeout of an entry from the diagnostics tables. The value is given in seconds. A value of 0 implies no timeout." DEFVAL { 3600 } ::= { extremeWirelessClientDiagCfgEntry 4 } -- *************************************************************** -- -- Per client historical feature status -- -- *************************************************************** -- extremeWirelessClientDiagStatusTable OBJECT-TYPE SYNTAX SEQUENCE OF ExtremeWirelessClientDiagStatusEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains one entry per virtual interface. Values stored here give current status of the historical client diag feature." ::= { extremeAP 32 } extremeWirelessClientDiagStatusEntry OBJECT-TYPE SYNTAX ExtremeWirelessClientDiagStatusEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Note that ifIndex here is virtual ifIndex (SSID)." INDEX { ifIndex } ::= { extremeWirelessClientDiagStatusTable 1 } ExtremeWirelessClientDiagStatusEntry ::= SEQUENCE { extremeWirelessClientDiagCurrentTableSize Unsigned32, extremeWirelessClientDiagTableWatermark Unsigned32, extremeWirelessClientDiagTotalOverflows Unsigned32, extremeWirelessClientDiagTotalTimeouts Unsigned32, extremeWirelessClientDiagLastElement TimeTicks, extremeWirelessClientDiagSupportsSizeCounters TruthValue, extremeWirelessClientDiagSupportsSpeedCounters TruthValue, extremeWirelessClientDiagSupportsPacketCounters TruthValue } extremeWirelessClientDiagCurrentTableSize OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This is the current size, in entries of the client diag tables." ::= { extremeWirelessClientDiagStatusEntry 1 } extremeWirelessClientDiagTableWatermark OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This is the maximum size the client diag table has been since the last time the statistics were cleared." ::= { extremeWirelessClientDiagStatusEntry 2 } extremeWirelessClientDiagTotalOverflows OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This is the total number of times an entry has been replaced by a newer entry because there was no room left in the table." ::= { extremeWirelessClientDiagStatusEntry 3 } extremeWirelessClientDiagTotalTimeouts OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This is the total number of times an entry has been aged-out of the table." ::= { extremeWirelessClientDiagStatusEntry 4 } extremeWirelessClientDiagLastElement OBJECT-TYPE SYNTAX TimeTicks MAX-ACCESS read-only STATUS current DESCRIPTION "This is sysUpTime when the last entry was added to the table." ::= { extremeWirelessClientDiagStatusEntry 5 } extremeWirelessClientDiagSupportsSpeedCounters OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION "This value indicates if this AP supports the speed-based counters from the extremeWirelessClientSpeedCountersTable." ::= { extremeWirelessClientDiagStatusEntry 6 } extremeWirelessClientDiagSupportsSizeCounters OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION "This value indicates if this AP supports the size-based counters from the extremeWirelessClientMACSizeCounterTable." ::= { extremeWirelessClientDiagStatusEntry 7 } extremeWirelessClientDiagSupportsPacketCounters OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION "This value indicates if this AP supports the packet-based counters from the extremeWirelessClientPacketCountersTable." ::= { extremeWirelessClientDiagStatusEntry 8 } -- *************************************************************** -- -- Per Client Historical Diagnostics : This table contains info -- -- about state transitions for each client. -- *************************************************************** -- extremeWirelessClientDiagTable OBJECT-TYPE SYNTAX SEQUENCE OF ExtremeWirelessClientDiagEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains information on a per-client basis. Rows are indexed first by virtual interface, then by client MAC." ::= { extremeAP 33 } extremeWirelessClientDiagEntry OBJECT-TYPE SYNTAX ExtremeWirelessClientDiagEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Note that ifIndex here is virtual ifIndex (SSID)." INDEX { ifIndex, extremeWirelessClientDiagMac } ::= { extremeWirelessClientDiagTable 1 } ExtremeWirelessClientDiagEntry ::= SEQUENCE { extremeWirelessClientDiagMac MacAddress, extremeWirelessClientDiagStateWatermark INTEGER, extremeWirelessClientDiagEntersInDetected Unsigned32, extremeWirelessClientDiagErrorsInDetected Unsigned32, extremeWirelessClientDiagAuthReqInDetected Unsigned32, extremeWirelessClientDiagOtherReqInDetected Unsigned32, extremeWirelessClientDiagMgmtActionInDetected Unsigned32, extremeWirelessClientDiagTimeOutInDetected Unsigned32, extremeWirelessClientDiagEntersInAuth Unsigned32, extremeWirelessClientDiagErrorsInAuth Unsigned32, extremeWirelessClientDiagAssocReqInAuth Unsigned32, extremeWirelessClientDiagOtherReqInAuth Unsigned32, extremeWirelessClientDiagMgmtActionInAuth Unsigned32, extremeWirelessClientDiagTimeOutInAuth Unsigned32, extremeWirelessClientDiagEntersInAssoc Unsigned32, extremeWirelessClientDiagErrorsInAssoc Unsigned32, extremeWirelessClientDiagMgmtActionInAssoc Unsigned32, extremeWirelessClientDiagTimeOutInAssoc Unsigned32, extremeWirelessClientDiagEntersInForward Unsigned32, extremeWirelessClientDiagMgmtActionInForward Unsigned32, extremeWirelessClientDiagTimeOutInForward Unsigned32, extremeWirelessClientDiagTotal802Auths Unsigned32, extremeWirelessClientDiagTotalNetLoginAuths Unsigned32 } extremeWirelessClientDiagMac OBJECT-TYPE SYNTAX MacAddress MAX-ACCESS read-only STATUS current DESCRIPTION "This is the MAC address of the station this entry describes." ::= { extremeWirelessClientDiagEntry 1 } extremeWirelessClientDiagStateWatermark OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "This is the highest state this client has been in." ::= { extremeWirelessClientDiagEntry 2 } extremeWirelessClientDiagEntersInDetected OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This is the total number of times the client has entered the detected state." ::= { extremeWirelessClientDiagEntry 3 } extremeWirelessClientDiagErrorsInDetected OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This is the total number of errors this client has experienced since the counters were cleared." ::= { extremeWirelessClientDiagEntry 4 } extremeWirelessClientDiagAuthReqInDetected OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This is the total number of AUTH REQ packets received from this client while it was in the detected state." ::= { extremeWirelessClientDiagEntry 5 } extremeWirelessClientDiagOtherReqInDetected OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This is the total number of REQ packets received from this client while it was in detected state that were not AUTH REQ packets." ::= { extremeWirelessClientDiagEntry 6 } extremeWirelessClientDiagMgmtActionInDetected OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This is the total number of times management initiated action (i.e. force-disassociate) was received for this client in the detected state." ::= { extremeWirelessClientDiagEntry 7 } extremeWirelessClientDiagTimeOutInDetected OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This is the total number of timeouts which happened to this client in the detected state." ::= { extremeWirelessClientDiagEntry 8 } extremeWirelessClientDiagEntersInAuth OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This is the total number of times the client has entered the AUTHED state." ::= { extremeWirelessClientDiagEntry 9 } extremeWirelessClientDiagErrorsInAuth OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This is the total number of times the client has had errors in the AUTHED state." ::= { extremeWirelessClientDiagEntry 10 } extremeWirelessClientDiagAssocReqInAuth OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This is the total number of ASSOC REQ or REASSOC REQ packets received from this client while in the AUTHED state." ::= { extremeWirelessClientDiagEntry 11 } extremeWirelessClientDiagOtherReqInAuth OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This is the total number of non-ASSOC/REASSOC packets received from this client while in the AUTHED state." ::= { extremeWirelessClientDiagEntry 12 } extremeWirelessClientDiagMgmtActionInAuth OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This is the total number of management initiated action which this client experienced while in the AUTHED state." ::= { extremeWirelessClientDiagEntry 13 } extremeWirelessClientDiagTimeOutInAuth OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This is the total number of times this client timed out while in the authed state." ::= { extremeWirelessClientDiagEntry 14 } extremeWirelessClientDiagEntersInAssoc OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This is the total number of times this client has entered the associated state." ::= { extremeWirelessClientDiagEntry 15 } extremeWirelessClientDiagErrorsInAssoc OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This is the total number of errors this client has had in the associated state." ::= { extremeWirelessClientDiagEntry 16 } extremeWirelessClientDiagMgmtActionInAssoc OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This is the total number of management actions which have happened to this client in the associated state." ::= { extremeWirelessClientDiagEntry 17 } extremeWirelessClientDiagTimeOutInAssoc OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This is the total number of times this station has been timed-out in the associated state." ::= { extremeWirelessClientDiagEntry 18 } extremeWirelessClientDiagEntersInForward OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This is the total number of times this client has entered the forwarding state." ::= { extremeWirelessClientDiagEntry 19 } extremeWirelessClientDiagMgmtActionInForward OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This is the total number of times this client has experience a management action while in forwarding." ::= { extremeWirelessClientDiagEntry 20 } extremeWirelessClientDiagTimeOutInForward OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This is the total number of timeouts this client has experienced while in forwarding." ::= { extremeWirelessClientDiagEntry 21 } extremeWirelessClientDiagTotal802Auths OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This is the total number of times this client has tried to authenticate using 802.1x." ::= { extremeWirelessClientDiagEntry 22 } extremeWirelessClientDiagTotalNetLoginAuths OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This is the total number of times this client has tried to authenticate using NetLogin." ::= { extremeWirelessClientDiagEntry 23 } -- *************************************************************** -- -- Per Client Association Information : This table gives history -- -- on the association packets sent by each client on the AP. -- -- *************************************************************** -- extremeWirelessClientAssocInfoTable OBJECT-TYPE SYNTAX SEQUENCE OF ExtremeWirelessClientAssocInfoEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains one row per client on a wireless interface. It gives information about the association history and parameters of that client." ::= { extremeAP 34 } extremeWirelessClientAssocInfoEntry OBJECT-TYPE SYNTAX ExtremeWirelessClientAssocInfoEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Note that ifIndex here is virtual ifIndex (SSID)." INDEX { ifIndex, extremeWirelessClientDiagMac } ::= { extremeWirelessClientAssocInfoTable 1 } ExtremeWirelessClientAssocInfoEntry ::= SEQUENCE { extremeWirelessClientAssocInfoAssociated TruthValue, extremeWirelessClientAssocInfoTotalAssocReq Unsigned32, extremeWirelessClientAssocInfoTotalReAssocReq Unsigned32, extremeWirelessClientAssocInfoTotalAssocResp Unsigned32, extremeWirelessClientAssocInfoTotalAssocOK Unsigned32, extremeWirelessClientAssocInfoTotalAssocFail Unsigned32, extremeWirelessClientAssocInfoTotalDisassocReq Unsigned32, extremeWirelessClientAssocInfoTotalDisassocResp Unsigned32, extremeWirelessClientAssocInfoRateIE OCTET STRING, extremeWirelessClientAssocInfoLastAssoc TimeTicks, extremeWirelessClientAssocInfoLastError TimeTicks, extremeWirelessClientAssocInfoLastErrorType INTEGER, extremeWirelessClientAssocInfoErrorRateMismatch Unsigned32, extremeWirelessClientAssocInfoErrorBadState Unsigned32, extremeWirelessClientAssocInfoErrorBadCapability Unsigned32, extremeWirelessClientAssocInfoErrorCounterMeasure Unsigned32, extremeWirelessClientAssocInfoErrorMcastCipher Unsigned32, extremeWirelessClientAssocInfoErrorMaxAssoc Unsigned32, extremeWirelessClientAssocInfoErrorRSNRequired Unsigned32, extremeWirelessClientAssocInfoErrorRSNMismatch Unsigned32, extremeWirelessClientAssocInfoErrorOther Unsigned32, extremeWirelessClientAssocInfoWPAIEPresent TruthValue, extremeWirelessClientAssocInfoWPAVersion Unsigned32, extremeWirelessClientAssocInfoWPAIEMcastCipher WPACipherSet, extremeWirelessClientAssocInfoWPAUcastCipherCount Unsigned32, extremeWirelessClientAssocInfoWPAUcastCipher WPACipherSet, extremeWirelessClientAssocInfoWPAKeyMgmtCount Unsigned32, extremeWirelessClientAssocInfoWPAKeyMgmtSuite WPAKeyMgmtSet, extremeWirelessClientAssocIEBlob OCTET STRING } extremeWirelessClientAssocInfoAssociated OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION "This gives the current MAC-layer association status of this client." ::= { extremeWirelessClientAssocInfoEntry 1 } extremeWirelessClientAssocInfoTotalAssocReq OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This gives the total number of ASSOC REQ pdus recieved from this client since the last time the counters were cleared." ::= { extremeWirelessClientAssocInfoEntry 2 } extremeWirelessClientAssocInfoTotalReAssocReq OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This gives the total number of REASSOC REQ PDUs received from this client since the last time the counters were cleared." ::= { extremeWirelessClientAssocInfoEntry 3 } extremeWirelessClientAssocInfoTotalAssocResp OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This gives the total number of ASSOC RESP pdus sent to this client since the last time the counters were cleared." ::= { extremeWirelessClientAssocInfoEntry 4 } extremeWirelessClientAssocInfoTotalAssocOK OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This gives the total number of ASSOC RESP PDUs which carried a status = ok response." ::= { extremeWirelessClientAssocInfoEntry 5 } extremeWirelessClientAssocInfoTotalAssocFail OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This gives the total number of ASSOC RESP PDUs which carried a status = failed response." ::= { extremeWirelessClientAssocInfoEntry 6 } extremeWirelessClientAssocInfoTotalDisassocReq OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This gives the total number of ASSOC RESP PDUs which carried a status = failed response." ::= { extremeWirelessClientAssocInfoEntry 7 } extremeWirelessClientAssocInfoTotalDisassocResp OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This gives the total number of ASSOC RESP PDUs which carried a status = failed response." ::= { extremeWirelessClientAssocInfoEntry 8 } extremeWirelessClientAssocInfoRateIE OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-only STATUS current DESCRIPTION "This is the value of the rate IE carried in the last ASSOC REQ packet if this wireless interface is configured to keep IEs. If it's not, this will be NULL. The IE is encoded as a series of bytes exactly as the value portion of the IE in the PDU." ::= { extremeWirelessClientAssocInfoEntry 9 } extremeWirelessClientAssocInfoLastAssoc OBJECT-TYPE SYNTAX TimeTicks MAX-ACCESS read-only STATUS current DESCRIPTION "This is sysUpTime when the last ASSOC REQ was received from this client." ::= { extremeWirelessClientAssocInfoEntry 10 } extremeWirelessClientAssocInfoLastError OBJECT-TYPE SYNTAX TimeTicks MAX-ACCESS read-only STATUS current DESCRIPTION "This is sysUpTime when the last ASSOC RESP was sent to this client with a failure status." ::= { extremeWirelessClientAssocInfoEntry 11 } extremeWirelessClientAssocInfoLastErrorType OBJECT-TYPE SYNTAX INTEGER { noError(0), rateMismatch(1), badState(2), badCapability(3), couterMeasure(4), mcastCipher(5), maxAssoc(6), rsnRequired(7), rsnMismatch(8), otherError(9) } MAX-ACCESS read-only STATUS current DESCRIPTION "This is an enumerated type which indicates which was the last error this client experienced during association." ::= { extremeWirelessClientAssocInfoEntry 12 } extremeWirelessClientAssocInfoErrorRateMismatch OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This is the total number of failed associations due to a mismatch of the rate IEs." ::= { extremeWirelessClientAssocInfoEntry 13 } extremeWirelessClientAssocInfoErrorBadState OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This is the total number of failed associations due to the client being in the wrong state." ::= { extremeWirelessClientAssocInfoEntry 14 } extremeWirelessClientAssocInfoErrorBadCapability OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This is the total number of failed associations due to the client having a capability mismatch with the AP." ::= { extremeWirelessClientAssocInfoEntry 15 } extremeWirelessClientAssocInfoErrorCounterMeasure OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This is the total number of failed associations due to the client being subject to a counter measure." ::= { extremeWirelessClientAssocInfoEntry 16 } extremeWirelessClientAssocInfoErrorMcastCipher OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This is the total number of failed associations due to the client not supporting the current multicast cipher." ::= { extremeWirelessClientAssocInfoEntry 17 } extremeWirelessClientAssocInfoErrorMaxAssoc OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This is the total number of failed associations due to the AP having too many associations already." ::= { extremeWirelessClientAssocInfoEntry 18 } extremeWirelessClientAssocInfoErrorRSNRequired OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This is the total number of failed associations due to the client not supplying the (required) RSN IE." ::= { extremeWirelessClientAssocInfoEntry 19 } extremeWirelessClientAssocInfoErrorRSNMismatch OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This is the total number of failed associations due to the client's RSN IE not matching supported features on the AP." ::= { extremeWirelessClientAssocInfoEntry 20 } extremeWirelessClientAssocInfoErrorOther OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This is the total number of failed associations due to the client's RSN IE not matching supported features on the AP." ::= { extremeWirelessClientAssocInfoEntry 21 } extremeWirelessClientAssocInfoWPAIEPresent OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION "If this value is true it indicates that WPA information was gathered from this station in the last association request. If true, it implies the values of the WPA variables below are valid. If false, it indicates that this station did not send a WPA IE in its last association." ::= { extremeWirelessClientAssocInfoEntry 22 } extremeWirelessClientAssocInfoWPAVersion OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This value gives the version of WPA supported by this station. See IEEE 802.11i Draft 3.0 section 7 for meaning of various values." ::= { extremeWirelessClientAssocInfoEntry 23 } extremeWirelessClientAssocInfoWPAIEMcastCipher OBJECT-TYPE SYNTAX WPACipherSet MAX-ACCESS read-only STATUS current DESCRIPTION "This value gives the single multicast cipher supported by this client." ::= { extremeWirelessClientAssocInfoEntry 24 } extremeWirelessClientAssocInfoWPAUcastCipherCount OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This gives the number of set bits in the ucast cipher variable below. In this case this number should always be 1." ::= { extremeWirelessClientAssocInfoEntry 25 } extremeWirelessClientAssocInfoWPAUcastCipher OBJECT-TYPE SYNTAX WPACipherSet MAX-ACCESS read-only STATUS current DESCRIPTION "This gives the cipher suites which was requested by this client during its last assoc req." ::= { extremeWirelessClientAssocInfoEntry 26 } extremeWirelessClientAssocInfoWPAKeyMgmtCount OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This value gives the number of key management suites requested by this client in the last assoc. req message. It indicates the number of set bits in the mgmt suite variable below." ::= { extremeWirelessClientAssocInfoEntry 27 } extremeWirelessClientAssocInfoWPAKeyMgmtSuite OBJECT-TYPE SYNTAX WPAKeyMgmtSet MAX-ACCESS read-only STATUS current DESCRIPTION "Gives the key management suite requested by this client during its last association request." ::= { extremeWirelessClientAssocInfoEntry 28 } extremeWirelessClientAssocIEBlob OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-only STATUS current DESCRIPTION "This is the IE list sent in the association frame encoded as a series of TLVs." ::= { extremeWirelessClientAssocInfoEntry 29 } -- *************************************************************** -- -- Authentication Information Table : This table contains infor on -- -- the MAC-layer authentication of each client which has tried to -- -- authenticate with this AP. -- *************************************************************** -- extremeWirelessClientAuthInfoTable OBJECT-TYPE SYNTAX SEQUENCE OF ExtremeWirelessClientAuthInfoEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains one row per client on a wireless interface. It gives information about the authentication history and params of that client." ::= { extremeAP 35 } extremeWirelessClientAuthInfoEntry OBJECT-TYPE SYNTAX ExtremeWirelessClientAuthInfoEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Note that ifIndex here is virtual ifIndex (SSID)." INDEX { ifIndex, extremeWirelessClientDiagMac } ::= { extremeWirelessClientAuthInfoTable 1 } ExtremeWirelessClientAuthInfoEntry ::= SEQUENCE { extremeWirelessClientAuthInfoCurrentAuth TruthValue, extremeWirelessClientAuthInfoTotalAuths Unsigned32, extremeWirelessClientAuthInfoTotalAuthResp Unsigned32, extremeWirelessClientAuthInfoTotalAuthsOK Unsigned32, extremeWirelessClientAuthInfoTotalAuthsFailed Unsigned32, extremeWirelessClientAuthInfoTotalDeauthReq Unsigned32, extremeWirelessClientAuthInfoTotalDeauthResp Unsigned32, extremeWirelessClientAuthInfoTotalOpen Unsigned32, extremeWirelessClientAuthInfoTotalShared Unsigned32, extremeWirelessClientAuthInfoLastAuth TimeTicks, extremeWirelessClientAuthInfoLastAuthType INTEGER, extremeWirelessClientAuthInfoLastError TimeTicks, extremeWirelessClientAuthInfoLastErrorType INTEGER, extremeWirelessClientAuthInfoErrorResourceFailure Unsigned32, extremeWirelessClientAuthInfoErrorSequenceNum Unsigned32, extremeWirelessClientAuthInfoErrorChallengeText Unsigned32, extremeWirelessClientAuthInfoErrorTypeMismatch Unsigned32, extremeWirelessClientAuthInfoErrorKeyIndex Unsigned32, extremeWirelessClientAuthInfoErrorOther Unsigned32 } extremeWirelessClientAuthInfoCurrentAuth OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION "This gives the current MAC-layer authentication status of the client." ::= { extremeWirelessClientAuthInfoEntry 1 } extremeWirelessClientAuthInfoTotalAuths OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This is the total number of AUTH REQ packets received from this client since the last time the counters were cleared." ::= { extremeWirelessClientAuthInfoEntry 2 } extremeWirelessClientAuthInfoTotalAuthResp OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This is the total number of AUTH RESP packets sent to this client since the last time the counters were cleared." ::= { extremeWirelessClientAuthInfoEntry 3 } extremeWirelessClientAuthInfoTotalAuthsOK OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This is the total number of AUTH RESP packets sent to this client which carried a STATUS = OK message." ::= { extremeWirelessClientAuthInfoEntry 4 } extremeWirelessClientAuthInfoTotalAuthsFailed OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This is the total number of AUTH RESP packets sent to this client which carried a STATUS = Failed message." ::= { extremeWirelessClientAuthInfoEntry 5 } extremeWirelessClientAuthInfoTotalDeauthReq OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This is the total number of DEAUTH REQ packets sent from this client." ::= { extremeWirelessClientAuthInfoEntry 6 } extremeWirelessClientAuthInfoTotalDeauthResp OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This is the total number of DEAUTH RESP packets sent to this client." ::= { extremeWirelessClientAuthInfoEntry 7 } extremeWirelessClientAuthInfoTotalOpen OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This is the total number of AUTH REQ packets which requested open authentication from the AP." ::= { extremeWirelessClientAuthInfoEntry 8 } extremeWirelessClientAuthInfoTotalShared OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This is the total number of AUTH REQ packets which requested shared authentication from the AP." ::= { extremeWirelessClientAuthInfoEntry 9 } extremeWirelessClientAuthInfoLastAuth OBJECT-TYPE SYNTAX TimeTicks MAX-ACCESS read-only STATUS current DESCRIPTION "This is the sysUpTime the last time this client sent a request for authentication." ::= { extremeWirelessClientAuthInfoEntry 10 } extremeWirelessClientAuthInfoLastAuthType OBJECT-TYPE SYNTAX INTEGER { open(1), shared(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "This is the last type of authentication requested by this client." ::= { extremeWirelessClientAuthInfoEntry 11 } extremeWirelessClientAuthInfoLastError OBJECT-TYPE SYNTAX TimeTicks MAX-ACCESS read-only STATUS current DESCRIPTION "This is the sysUpTime of the last authentication failure for this client." ::= { extremeWirelessClientAuthInfoEntry 12 } extremeWirelessClientAuthInfoLastErrorType OBJECT-TYPE SYNTAX INTEGER { noError(0), resourceFailure(1), sequenceNumber(2), challengeText(3), algorithmMismatch(4), keyIndex(5), otherError(6) } MAX-ACCESS read-only STATUS current DESCRIPTION "This is the OID of the last error counter that was incremented for this client." ::= { extremeWirelessClientAuthInfoEntry 13 } extremeWirelessClientAuthInfoErrorResourceFailure OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This is the total number of authentication failures which have resulted from resource failures." ::= { extremeWirelessClientAuthInfoEntry 14 } extremeWirelessClientAuthInfoErrorSequenceNum OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This is the total number of authentication failures which have resulted from bad packet sequence numbers." ::= { extremeWirelessClientAuthInfoEntry 15 } extremeWirelessClientAuthInfoErrorChallengeText OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This is the total number of authentication failures which have resutled from challenge text mismatch." ::= { extremeWirelessClientAuthInfoEntry 16 } extremeWirelessClientAuthInfoErrorTypeMismatch OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This is the total number of authentication failures which have resutled from the requested authentication type (i.e. open/shared) not matching what this virutal interface is configured for." ::= { extremeWirelessClientAuthInfoEntry 17 } extremeWirelessClientAuthInfoErrorKeyIndex OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This is the total number of authentication failures which have resulted from key index mismatches." ::= { extremeWirelessClientAuthInfoEntry 18 } extremeWirelessClientAuthInfoErrorOther OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This is the total number of authentication failures which have resulted from unspecified errors." ::= { extremeWirelessClientAuthInfoEntry 19 } -- *************************************************************** -- -- Client MAC information : This table contains statistics and -- -- information on each client which has tried to authenticate with -- -- this virtual interface. -- *************************************************************** -- extremeWirelessClientMACInfoTable OBJECT-TYPE SYNTAX SEQUENCE OF ExtremeWirelessClientMACInfoEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains one entry per source MAC which has tried to authenticate with this virtual interface (SSID). Entries are created when AUTH or REATH REQ packets are received from new clients. Entries can be aged out, removed by management action, or overwritten by an overflow." ::= { extremeAP 36 } extremeWirelessClientMACInfoEntry OBJECT-TYPE SYNTAX ExtremeWirelessClientMACInfoEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "" INDEX { ifIndex, extremeWirelessClientDiagMac } ::= { extremeWirelessClientMACInfoTable 1 } ExtremeWirelessClientMACInfoEntry ::= SEQUENCE { extremeWirelessClientMACInfoMinRSS INTEGER, extremeWirelessClientMACInfoMaxRSS INTEGER, extremeWirelessClientMACInfoAvgRSS INTEGER, extremeWirelessClientMACInfoTotalProbeReq Unsigned32, extremeWirelessClientMACInfoTotalAuthReq Unsigned32, extremeWirelessClientMACInfoTotalAssocReq Unsigned32, extremeWirelessClientMACInfoTotalReAssocReq Unsigned32, extremeWirelessClientMACInfoTotalDeAssocReq Unsigned32, extremeWirelessClientMACInfoTotalDeAuthReq Unsigned32, extremeWirelessClientMACInfoTotalPsPoll Unsigned32, extremeWirelessClientMACInfoTotalData Unsigned32, extremeWirelessClientMACInfoNavValue Unsigned32 } extremeWirelessClientMACInfoMinRSS OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "This gives the minimum RSS indication of any packet we have seen from this client. A value of 0 indicates that RSSI has been unavailable." ::= { extremeWirelessClientMACInfoEntry 1 } extremeWirelessClientMACInfoMaxRSS OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "This gives the maximum RSS indication of any packet we have seen from this client. A value of 0 indicates that RSSI has been unavailable." ::= { extremeWirelessClientMACInfoEntry 2 } extremeWirelessClientMACInfoAvgRSS OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "This gives the average RSS indication of any packet we have seen from this client. A value of 0 indicates that RSSI has been unavailable." ::= { extremeWirelessClientMACInfoEntry 3 } extremeWirelessClientMACInfoTotalProbeReq OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This gives the total number of PROBE REQ packets recieved from this client since the counters have been cleared." ::= { extremeWirelessClientMACInfoEntry 4 } extremeWirelessClientMACInfoTotalAuthReq OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This gives the total number of AUTH REQ packets recieved from this client since the counters have been cleared." ::= { extremeWirelessClientMACInfoEntry 5 } extremeWirelessClientMACInfoTotalAssocReq OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This gives the total number of ASSOC REQ packets recieved from this client since the counters have been cleared." ::= { extremeWirelessClientMACInfoEntry 6 } extremeWirelessClientMACInfoTotalReAssocReq OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This gives the total number of REASSOC REQ packets recieved from this client since the counters have been cleared." ::= { extremeWirelessClientMACInfoEntry 7 } extremeWirelessClientMACInfoTotalDeAssocReq OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This gives the total number of DEASSOC REQ packets recieved from this client since the counters have been cleared." ::= { extremeWirelessClientMACInfoEntry 8 } extremeWirelessClientMACInfoTotalDeAuthReq OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This gives the total number of DEAUTH REQ packets recieved from this client since the counters have been cleared." ::= { extremeWirelessClientMACInfoEntry 9 } extremeWirelessClientMACInfoTotalPsPoll OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This gives the total number of PS POLL packets recieved from this client since the counters have been cleared." ::= { extremeWirelessClientMACInfoEntry 10 } extremeWirelessClientMACInfoTotalData OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This gives the total number of data frames received from this client since the counters have been cleared." ::= { extremeWirelessClientMACInfoEntry 11 } extremeWirelessClientMACInfoNavValue OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "TODO: Is this an average, total, what?" ::= { extremeWirelessClientMACInfoEntry 12 } -- *************************************************************** -- -- Size Based Counters : This table gives per-client histogram -- -- counters based on the size of received packets/fragments. -- -- *************************************************************** -- extremeWirelessClientSizeCounterTable OBJECT-TYPE SYNTAX SEQUENCE OF ExtremeWirelessClientSizeCounterEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "There is one entry in this table for each client which has tried to authenticate with this virtual interface. A new entry is created when an AUTH or REATH REQ packet is received from a new station. Entries are removed by management action, timeout or overwritten due to overflow. Entries in this table are also indexed by virtual interface. A client which has tried to authenticate to multiple virtual interfaces may have more than one entry in this table." ::= { extremeAP 37 } extremeWirelessClientSizeCounterEntry OBJECT-TYPE SYNTAX ExtremeWirelessClientSizeCounterEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "" INDEX { ifIndex, extremeWirelessClientDiagMac } ::= { extremeWirelessClientSizeCounterTable 1 } ExtremeWirelessClientSizeCounterEntry ::= SEQUENCE { extremeWirelessClientFrameSizeReXmit64 Unsigned32, extremeWirelessClientFrameSizeReXmit128 Unsigned32, extremeWirelessClientFrameSizeReXmit256 Unsigned32, extremeWirelessClientFrameSizeReXmit512 Unsigned32, extremeWirelessClientFrameSizeReXmit1024 Unsigned32, extremeWirelessClientFrameSizeReXmit2048 Unsigned32, extremeWirelessClientFrameSizeTX64 Unsigned32, extremeWirelessClientFrameSizeTX128 Unsigned32, extremeWirelessClientFrameSizeTX256 Unsigned32, extremeWirelessClientFrameSizeTX512 Unsigned32, extremeWirelessClientFrameSizeTX1024 Unsigned32, extremeWirelessClientFrameSizeTX2048 Unsigned32, extremeWirelessClientFrameSizeRX64 Unsigned32, extremeWirelessClientFrameSizeRX128 Unsigned32, extremeWirelessClientFrameSizeRX256 Unsigned32, extremeWirelessClientFrameSizeRX512 Unsigned32, extremeWirelessClientFrameSizeRX1024 Unsigned32, extremeWirelessClientFrameSizeRX2048 Unsigned32, extremeWirelessClientFrameSizeErrorTX64 Unsigned32, extremeWirelessClientFrameSizeErrorTX128 Unsigned32, extremeWirelessClientFrameSizeErrorTX256 Unsigned32, extremeWirelessClientFrameSizeErrorTX512 Unsigned32, extremeWirelessClientFrameSizeErrorTX1024 Unsigned32, extremeWirelessClientFrameSizeErrorTX2048 Unsigned32, extremeWirelessClientFrameSizeErrorRX64 Unsigned32, extremeWirelessClientFrameSizeErrorRX128 Unsigned32, extremeWirelessClientFrameSizeErrorRX256 Unsigned32, extremeWirelessClientFrameSizeErrorRX512 Unsigned32, extremeWirelessClientFrameSizeErrorRX1024 Unsigned32, extremeWirelessClientFrameSizeErrorRX2048 Unsigned32, extremeWirelessClientPacketSizeTX64 Unsigned32, extremeWirelessClientPacketSizeTX128 Unsigned32, extremeWirelessClientPacketSizeTX256 Unsigned32, extremeWirelessClientPacketSizeTX512 Unsigned32, extremeWirelessClientPacketSizeTX1024 Unsigned32, extremeWirelessClientPacketSizeTX2048 Unsigned32, extremeWirelessClientPacketSizeRX64 Unsigned32, extremeWirelessClientPacketSizeRX128 Unsigned32, extremeWirelessClientPacketSizeRX256 Unsigned32, extremeWirelessClientPacketSizeRX512 Unsigned32, extremeWirelessClientPacketSizeRX1024 Unsigned32, extremeWirelessClientPacketSizeRX2048 Unsigned32 } extremeWirelessClientFrameSizeReXmit64 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This gives the number of frags retransmitted to this client which were less than or equal to 64 bytes in length." ::= { extremeWirelessClientSizeCounterEntry 1 } extremeWirelessClientFrameSizeReXmit128 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This gives the number of frags retransmitted to this client which were between 64 and 128 bytes in length." ::= { extremeWirelessClientSizeCounterEntry 2 } extremeWirelessClientFrameSizeReXmit256 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This gives the number of frags retransmitted to this client which were between 128 and 256 bytes in length." ::= { extremeWirelessClientSizeCounterEntry 3 } extremeWirelessClientFrameSizeReXmit512 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This gives the number of frags retransmitted to this client which were between 256 and 512 bytes in length." ::= { extremeWirelessClientSizeCounterEntry 4 } extremeWirelessClientFrameSizeReXmit1024 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This gives the number of frags retransmitted to this client which were between 512 and 1024 bytes in length." ::= { extremeWirelessClientSizeCounterEntry 5 } extremeWirelessClientFrameSizeReXmit2048 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This gives the number of frags retransmitted to this client which were between 1024 and 2048 bytes in length." ::= { extremeWirelessClientSizeCounterEntry 6 } extremeWirelessClientFrameSizeTX64 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This gives the number of frags transmitted to this client which were less than or equal to 64 bytes in length." ::= { extremeWirelessClientSizeCounterEntry 7 } extremeWirelessClientFrameSizeTX128 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This gives the number of frags transmitted to this client which were between 64 and 128 bytes in length." ::= { extremeWirelessClientSizeCounterEntry 8 } extremeWirelessClientFrameSizeTX256 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This gives the number of frags transmitted to this client which were between 128 and 256 bytes in length." ::= { extremeWirelessClientSizeCounterEntry 9 } extremeWirelessClientFrameSizeTX512 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This gives the number of frags transmitted to this client which were between 256 and 512 bytes in length." ::= { extremeWirelessClientSizeCounterEntry 10 } extremeWirelessClientFrameSizeTX1024 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This gives the number of frags transmitted to this client which were between 512 and 1024 bytes in length." ::= { extremeWirelessClientSizeCounterEntry 11 } extremeWirelessClientFrameSizeTX2048 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This gives the number of frags transmitted to this client which were between 1024 and 2048 bytes in length." ::= { extremeWirelessClientSizeCounterEntry 12 } extremeWirelessClientFrameSizeRX64 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This gives the number of frags received from this client which were less than or equal to 64 bytes in length." ::= { extremeWirelessClientSizeCounterEntry 13 } extremeWirelessClientFrameSizeRX128 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This gives the number of frags received from this client which were between 64 and 128 bytes in length." ::= { extremeWirelessClientSizeCounterEntry 14 } extremeWirelessClientFrameSizeRX256 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This gives the number of frags received from this client which were between 128 and 256 bytes in length." ::= { extremeWirelessClientSizeCounterEntry 15 } extremeWirelessClientFrameSizeRX512 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This gives the number of frags received from this client which were between 256 and 512 bytes in length." ::= { extremeWirelessClientSizeCounterEntry 16 } extremeWirelessClientFrameSizeRX1024 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This gives the number of frags received from this client which were between 512 and 1024 bytes in length." ::= { extremeWirelessClientSizeCounterEntry 17 } extremeWirelessClientFrameSizeRX2048 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This gives the number of frags received from this client which were between 1024 and 2048 bytes in length." ::= { extremeWirelessClientSizeCounterEntry 18 } extremeWirelessClientFrameSizeErrorTX64 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This gives the number of frags which failed to be sent from this client with a length between 0 and 64 bytes." ::= { extremeWirelessClientSizeCounterEntry 19 } extremeWirelessClientFrameSizeErrorTX128 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This gives the number of frags which failed to be sent from this client with a length between 65 and 128 bytes." ::= { extremeWirelessClientSizeCounterEntry 20 } extremeWirelessClientFrameSizeErrorTX256 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This gives the number of frags which failed to be sent from this client with a length between 129 and 256 bytes." ::= { extremeWirelessClientSizeCounterEntry 21 } extremeWirelessClientFrameSizeErrorTX512 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This gives the number of frags which failed to be sent from this client with a length between 257 and 512 bytes." ::= { extremeWirelessClientSizeCounterEntry 22 } extremeWirelessClientFrameSizeErrorTX1024 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This gives the number of frags which failed to be sent from this client with a length between 513 and 1024 bytes." ::= { extremeWirelessClientSizeCounterEntry 23 } extremeWirelessClientFrameSizeErrorTX2048 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This gives the number of frags which failed to be sent from this client with a length between 1025 and 2048 bytes." ::= { extremeWirelessClientSizeCounterEntry 24 } extremeWirelessClientFrameSizeErrorRX64 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This gives the number of frags which were received with an FCS or other error and a length between 0 and 64 bytes." ::= { extremeWirelessClientSizeCounterEntry 25 } extremeWirelessClientFrameSizeErrorRX128 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This gives the number of frags which were received with an FCS or other error and a length between 65 and 128 bytes." ::= { extremeWirelessClientSizeCounterEntry 26 } extremeWirelessClientFrameSizeErrorRX256 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This gives the number of frags which were received with an FCS or other error and a length between 129 and 256 bytes." ::= { extremeWirelessClientSizeCounterEntry 27 } extremeWirelessClientFrameSizeErrorRX512 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This gives the number of frags which were received with an FCS or other error and a length between 257 and 512 bytes." ::= { extremeWirelessClientSizeCounterEntry 28 } extremeWirelessClientFrameSizeErrorRX1024 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This gives the number of frags which were received with an FCS or other error and a length between 513 and 1024 bytes." ::= { extremeWirelessClientSizeCounterEntry 29 } extremeWirelessClientFrameSizeErrorRX2048 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This gives the number of frags which were received with an FCS or other error and a length between 1025 and 2048 bytes." ::= { extremeWirelessClientSizeCounterEntry 30 } extremeWirelessClientPacketSizeTX64 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This gives the number of packets transmitted to this client which were less than or equal to 64 bytes in length." ::= { extremeWirelessClientSizeCounterEntry 31 } extremeWirelessClientPacketSizeTX128 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This gives the number of packets transmitted to this client which were between 64 and 128 bytes in length." ::= { extremeWirelessClientSizeCounterEntry 32 } extremeWirelessClientPacketSizeTX256 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This gives the number of packets transmitted to this client which were between 128 and 256 bytes in length." ::= { extremeWirelessClientSizeCounterEntry 33 } extremeWirelessClientPacketSizeTX512 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This gives the number of packets transmitted to this client which were between 256 and 512 bytes in length." ::= { extremeWirelessClientSizeCounterEntry 34 } extremeWirelessClientPacketSizeTX1024 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This gives the number of packets transmitted to this client which were between 512 and 1024 bytes in length." ::= { extremeWirelessClientSizeCounterEntry 35 } extremeWirelessClientPacketSizeTX2048 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This gives the number of packets transmitted to this client which were between 1024 and 2048 bytes in length." ::= { extremeWirelessClientSizeCounterEntry 36 } extremeWirelessClientPacketSizeRX64 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This gives the number of packets received from this client which were less than or equal to 64 bytes in length." ::= { extremeWirelessClientSizeCounterEntry 37 } extremeWirelessClientPacketSizeRX128 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This gives the number of packets received from this client which were between 64 and 128 bytes in length." ::= { extremeWirelessClientSizeCounterEntry 38 } extremeWirelessClientPacketSizeRX256 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This gives the number of packets received from this client which were between 128 and 256 bytes in length." ::= { extremeWirelessClientSizeCounterEntry 39 } extremeWirelessClientPacketSizeRX512 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This gives the number of packets received from this client which were between 256 and 512 bytes in length." ::= { extremeWirelessClientSizeCounterEntry 40 } extremeWirelessClientPacketSizeRX1024 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This gives the number of packets received from this client which were between 512 and 1024 bytes in length." ::= { extremeWirelessClientSizeCounterEntry 41 } extremeWirelessClientPacketSizeRX2048 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This gives the number of packets received from this client which were between 1024 and 2048 bytes in length." ::= { extremeWirelessClientSizeCounterEntry 42 } -- *************************************************************** -- -- Per Client Speed : This table gives a histogram of statistics -- -- based on the speed of transmission/reception of packets on a -- -- virtual interface. -- -- *************************************************************** -- extremeWirelessClientSpeedCounterTable OBJECT-TYPE SYNTAX SEQUENCE OF ExtremeWirelessClientSpeedCounterEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table is indexed by wireless interface index. These are the virtual interfaces corresponding to the SSID. Support for this table is optional, indicated by the value of the variable extremeWirelessClientDiagSupportsSpeedCounters in the status table." ::= { extremeAP 38 } extremeWirelessClientSpeedCounterEntry OBJECT-TYPE SYNTAX ExtremeWirelessClientSpeedCounterEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The ifIndex here is the wireless interface (SSID). It is expected that an entry will be created in this table only after a client sends a AUTH or REATH packet to the SSID." INDEX { ifIndex, extremeWirelessClientDiagMac } ::= { extremeWirelessClientSpeedCounterTable 1 } ExtremeWirelessClientSpeedCounterEntry ::= SEQUENCE { extremeWirelessClientSpeedReXmit1 Unsigned32, extremeWirelessClientSpeedReXmit2 Unsigned32, extremeWirelessClientSpeedReXmit5p5 Unsigned32, extremeWirelessClientSpeedReXmit6 Unsigned32, extremeWirelessClientSpeedReXmit9 Unsigned32, extremeWirelessClientSpeedReXmit12 Unsigned32, extremeWirelessClientSpeedReXmit18 Unsigned32, extremeWirelessClientSpeedReXmit24 Unsigned32, extremeWirelessClientSpeedReXmit36 Unsigned32, extremeWirelessClientSpeedReXmit48 Unsigned32, extremeWirelessClientSpeedReXmit54 Unsigned32, extremeWirelessClientSpeedTX1 Unsigned32, extremeWirelessClientSpeedTX2 Unsigned32, extremeWirelessClientSpeedTX5p5 Unsigned32, extremeWirelessClientSpeedTX6 Unsigned32, extremeWirelessClientSpeedTX9 Unsigned32, extremeWirelessClientSpeedTX12 Unsigned32, extremeWirelessClientSpeedTX18 Unsigned32, extremeWirelessClientSpeedTX24 Unsigned32, extremeWirelessClientSpeedTX36 Unsigned32, extremeWirelessClientSpeedTX48 Unsigned32, extremeWirelessClientSpeedTX54 Unsigned32, extremeWirelessClientSpeedRX1 Unsigned32, extremeWirelessClientSpeedRX2 Unsigned32, extremeWirelessClientSpeedRX5p5 Unsigned32, extremeWirelessClientSpeedRX6 Unsigned32, extremeWirelessClientSpeedRX9 Unsigned32, extremeWirelessClientSpeedRX12 Unsigned32, extremeWirelessClientSpeedRX18 Unsigned32, extremeWirelessClientSpeedRX24 Unsigned32, extremeWirelessClientSpeedRX36 Unsigned32, extremeWirelessClientSpeedRX48 Unsigned32, extremeWirelessClientSpeedRX54 Unsigned32 } extremeWirelessClientSpeedReXmit1 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This gives the number of frags which were retransmitted to the given client at 1 Mbps." ::= { extremeWirelessClientSpeedCounterEntry 1 } extremeWirelessClientSpeedReXmit2 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This gives the number of frags which were retransmitted to the given client at 2 Mbps." ::= { extremeWirelessClientSpeedCounterEntry 2 } extremeWirelessClientSpeedReXmit5p5 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This gives the number of frags which were retransmitted to the given client at 5 Mbps." ::= { extremeWirelessClientSpeedCounterEntry 3 } extremeWirelessClientSpeedReXmit6 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This gives the number of frags which were retransmitted to the given client at 6 Mbps." ::= { extremeWirelessClientSpeedCounterEntry 4 } extremeWirelessClientSpeedReXmit9 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This gives the number of frags which were retransmitted to the given client at 9 Mbps." ::= { extremeWirelessClientSpeedCounterEntry 5 } extremeWirelessClientSpeedReXmit12 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This gives the number of frags which were retransmitted to the given client at 12 Mbps." ::= { extremeWirelessClientSpeedCounterEntry 6 } extremeWirelessClientSpeedReXmit18 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This gives the number of frags which were retransmitted to the given client at 18 Mbps." ::= { extremeWirelessClientSpeedCounterEntry 7 } extremeWirelessClientSpeedReXmit24 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This gives the number of frags which were retransmitted to the given client at 24 Mbps." ::= { extremeWirelessClientSpeedCounterEntry 8 } extremeWirelessClientSpeedReXmit36 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This gives the number of frags which were retransmitted to the given client at 36 Mbps." ::= { extremeWirelessClientSpeedCounterEntry 9 } extremeWirelessClientSpeedReXmit48 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This gives the number of frags which were retransmitted to the given client at 48 Mbps." ::= { extremeWirelessClientSpeedCounterEntry 10 } extremeWirelessClientSpeedReXmit54 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This gives the number of frags which were retransmitted to the given client at 54 Mbps." ::= { extremeWirelessClientSpeedCounterEntry 11 } extremeWirelessClientSpeedTX1 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This gives the number of frags which were transmitted to the given client at 1 Mbps." ::= { extremeWirelessClientSpeedCounterEntry 12 } extremeWirelessClientSpeedTX2 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This gives the number of frags which were transmitted to the given client at 2 Mbps." ::= { extremeWirelessClientSpeedCounterEntry 13 } extremeWirelessClientSpeedTX5p5 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This gives the number of frags which were transmitted to the given client at 5 Mbps." ::= { extremeWirelessClientSpeedCounterEntry 14 } extremeWirelessClientSpeedTX6 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This gives the number of frags which were transmitted to the given client at 6 Mbps." ::= { extremeWirelessClientSpeedCounterEntry 15 } extremeWirelessClientSpeedTX9 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This gives the number of frags which were transmitted to the given client at 9 Mbps." ::= { extremeWirelessClientSpeedCounterEntry 16 } extremeWirelessClientSpeedTX12 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This gives the number of frags which were transmitted to the given client at 12 Mbps." ::= { extremeWirelessClientSpeedCounterEntry 17 } extremeWirelessClientSpeedTX18 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This gives the number of frags which were transmitted to the given client at 18 Mbps." ::= { extremeWirelessClientSpeedCounterEntry 18 } extremeWirelessClientSpeedTX24 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This gives the number of frags which were transmitted to the given client at 24 Mbps." ::= { extremeWirelessClientSpeedCounterEntry 19 } extremeWirelessClientSpeedTX36 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This gives the number of frags which were transmitted to the given client at 36 Mbps." ::= { extremeWirelessClientSpeedCounterEntry 20 } extremeWirelessClientSpeedTX48 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This gives the number of frags which were transmitted to the given client at 48 Mbps." ::= { extremeWirelessClientSpeedCounterEntry 21 } extremeWirelessClientSpeedTX54 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This gives the number of frags which were transmitted to the given client at 54 Mbps." ::= { extremeWirelessClientSpeedCounterEntry 22 } extremeWirelessClientSpeedRX1 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This gives the number of frags which were received from the given client at 1 Mbps." ::= { extremeWirelessClientSpeedCounterEntry 23 } extremeWirelessClientSpeedRX2 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This gives the number of frags which were received from the given client at 2 Mbps." ::= { extremeWirelessClientSpeedCounterEntry 24 } extremeWirelessClientSpeedRX5p5 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This gives the number of frags which were received from the given client at 5 Mbps." ::= { extremeWirelessClientSpeedCounterEntry 25 } extremeWirelessClientSpeedRX6 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This gives the number of frags which were received from the given client at 6 Mbps." ::= { extremeWirelessClientSpeedCounterEntry 26 } extremeWirelessClientSpeedRX9 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This gives the number of frags which were received from the given client at 9 Mbps." ::= { extremeWirelessClientSpeedCounterEntry 27 } extremeWirelessClientSpeedRX12 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This gives the number of frags which were received from the given client at 12 Mbps." ::= { extremeWirelessClientSpeedCounterEntry 28 } extremeWirelessClientSpeedRX18 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This gives the number of frags which were received from the given client at 18 Mbps." ::= { extremeWirelessClientSpeedCounterEntry 29 } extremeWirelessClientSpeedRX24 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This gives the number of frags which were received from the given client at 24 Mbps." ::= { extremeWirelessClientSpeedCounterEntry 30 } extremeWirelessClientSpeedRX36 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This gives the number of frags which were received from the given client at 36 Mbps." ::= { extremeWirelessClientSpeedCounterEntry 31 } extremeWirelessClientSpeedRX48 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This gives the number of frags which were received from the given client at 48 Mbps." ::= { extremeWirelessClientSpeedCounterEntry 32 } extremeWirelessClientSpeedRX54 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This gives the number of frags which were received from the given client at 54 Mbps." ::= { extremeWirelessClientSpeedCounterEntry 33 } -- *************************************************************** -- -- Frame Size Table : This table presents a historgram of frames -- -- based on type and size. -- -- *************************************************************** -- extremeWirelessIntfFrameSizeTable OBJECT-TYPE SYNTAX SEQUENCE OF ExtremeWirelessIntfFrameSizeEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "There is one entry in this table for each virtual and physical interface. Values for physical interfaces are summations of the values for the constituent virtual interfaces." ::= { extremeAP 39 } extremeWirelessIntfFrameSizeEntry OBJECT-TYPE SYNTAX ExtremeWirelessIntfFrameSizeEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "" INDEX { ifIndex } ::= { extremeWirelessIntfFrameSizeTable 1 } ExtremeWirelessIntfFrameSizeEntry ::= SEQUENCE { extremeWirelessIntfFrameSizeMgmtTX64 Unsigned32, extremeWirelessIntfFrameSizeMgmtTX128 Unsigned32, extremeWirelessIntfFrameSizeMgmtTX256 Unsigned32, extremeWirelessIntfFrameSizeMgmtTX512 Unsigned32, extremeWirelessIntfFrameSizeMgmtTX1024 Unsigned32, extremeWirelessIntfFrameSizeMgmtTX2048 Unsigned32, extremeWirelessIntfFrameSizeMgmtRX64 Unsigned32, extremeWirelessIntfFrameSizeMgmtRX128 Unsigned32, extremeWirelessIntfFrameSizeMgmtRX256 Unsigned32, extremeWirelessIntfFrameSizeMgmtRX512 Unsigned32, extremeWirelessIntfFrameSizeMgmtRX1024 Unsigned32, extremeWirelessIntfFrameSizeMgmtRX2048 Unsigned32, extremeWirelessIntfFrameSizeCtlTX64 Unsigned32, extremeWirelessIntfFrameSizeCtlTX128 Unsigned32, extremeWirelessIntfFrameSizeCtlTX256 Unsigned32, extremeWirelessIntfFrameSizeCtlTX512 Unsigned32, extremeWirelessIntfFrameSizeCtlTX1024 Unsigned32, extremeWirelessIntfFrameSizeCtlTX2048 Unsigned32, extremeWirelessIntfFrameSizeCtlRX64 Unsigned32, extremeWirelessIntfFrameSizeCtlRX128 Unsigned32, extremeWirelessIntfFrameSizeCtlRX256 Unsigned32, extremeWirelessIntfFrameSizeCtlRX512 Unsigned32, extremeWirelessIntfFrameSizeCtlRX1024 Unsigned32, extremeWirelessIntfFrameSizeCtlRX2048 Unsigned32, extremeWirelessIntfFrameSizeDataTX64 Unsigned32, extremeWirelessIntfFrameSizeDataTX128 Unsigned32, extremeWirelessIntfFrameSizeDataTX256 Unsigned32, extremeWirelessIntfFrameSizeDataTX512 Unsigned32, extremeWirelessIntfFrameSizeDataTX1024 Unsigned32, extremeWirelessIntfFrameSizeDataTX2048 Unsigned32, extremeWirelessIntfFrameSizeDataRX64 Unsigned32, extremeWirelessIntfFrameSizeDataRX128 Unsigned32, extremeWirelessIntfFrameSizeDataRX256 Unsigned32, extremeWirelessIntfFrameSizeDataRX512 Unsigned32, extremeWirelessIntfFrameSizeDataRX1024 Unsigned32, extremeWirelessIntfFrameSizeDataRX2048 Unsigned32 } extremeWirelessIntfFrameSizeMgmtTX64 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This gives the number of management-type frames transmitted on this interface which were less than or equal to 64 bytes in length." ::= { extremeWirelessIntfFrameSizeEntry 1 } extremeWirelessIntfFrameSizeMgmtTX128 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This gives the number of management-type frames transmitted on this interface which were between 65 and 128 bytes in length." ::= { extremeWirelessIntfFrameSizeEntry 2 } extremeWirelessIntfFrameSizeMgmtTX256 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This gives the number of management-type frames transmitted on this interface which were between 129 and 256 bytes in length." ::= { extremeWirelessIntfFrameSizeEntry 3 } extremeWirelessIntfFrameSizeMgmtTX512 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This gives the number of management-type frames transmitted on this interface which were between 257 and 512 bytes in length." ::= { extremeWirelessIntfFrameSizeEntry 4 } extremeWirelessIntfFrameSizeMgmtTX1024 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This gives the number of management-type frames transmitted on this interface which were between 513 and 1024 bytes in length." ::= { extremeWirelessIntfFrameSizeEntry 5 } extremeWirelessIntfFrameSizeMgmtTX2048 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This gives the number of management-type frames transmitted on this interface which were between 1025 and 2048 bytes in length." ::= { extremeWirelessIntfFrameSizeEntry 6 } extremeWirelessIntfFrameSizeMgmtRX64 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This gives the number of management-type frames received on this interface which were less than or equal to 64 bytes in length." ::= { extremeWirelessIntfFrameSizeEntry 7 } extremeWirelessIntfFrameSizeMgmtRX128 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This gives the number of management-type frames received on this interface which were between 65 and 128 bytes in length." ::= { extremeWirelessIntfFrameSizeEntry 8 } extremeWirelessIntfFrameSizeMgmtRX256 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This gives the number of management-type frames received on this interface which were between 129 and 256 bytes in length." ::= { extremeWirelessIntfFrameSizeEntry 9 } extremeWirelessIntfFrameSizeMgmtRX512 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This gives the number of management-type frames received on this interface which were between 257 and 512 bytes in length." ::= { extremeWirelessIntfFrameSizeEntry 10 } extremeWirelessIntfFrameSizeMgmtRX1024 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This gives the number of management-type frames received on this interface which were between 513 and 1024 bytes in length." ::= { extremeWirelessIntfFrameSizeEntry 11 } extremeWirelessIntfFrameSizeMgmtRX2048 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This gives the number of management-type frames received on this interface which were between 1025 and 2048 bytes in length." ::= { extremeWirelessIntfFrameSizeEntry 12 } extremeWirelessIntfFrameSizeCtlTX64 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This gives the number of control-type frames transmitted on this interface which were less than or equal to 64 bytes in length." ::= { extremeWirelessIntfFrameSizeEntry 13 } extremeWirelessIntfFrameSizeCtlTX128 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This gives the number of control-type frames transmitted on this interface which were between 65 and 128 bytes in length." ::= { extremeWirelessIntfFrameSizeEntry 14 } extremeWirelessIntfFrameSizeCtlTX256 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This gives the number of control-type frames transmitted on this interface which were between 129 and 256 bytes in length." ::= { extremeWirelessIntfFrameSizeEntry 15 } extremeWirelessIntfFrameSizeCtlTX512 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This gives the number of control-type frames transmitted on this interface which were between 257 and 512 bytes in length." ::= { extremeWirelessIntfFrameSizeEntry 16 } extremeWirelessIntfFrameSizeCtlTX1024 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This gives the number of control-type frames transmitted on this interface which were between 513 and 1024 bytes in length." ::= { extremeWirelessIntfFrameSizeEntry 17 } extremeWirelessIntfFrameSizeCtlTX2048 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This gives the number of control-type frames transmitted on this interface which were between 1025 and 2048 bytes in length." ::= { extremeWirelessIntfFrameSizeEntry 18 } extremeWirelessIntfFrameSizeCtlRX64 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This gives the number of control-type frames received on this interface which were less than or equal to 64 bytes in length." ::= { extremeWirelessIntfFrameSizeEntry 19 } extremeWirelessIntfFrameSizeCtlRX128 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This gives the number of control-type frames received on this interface which were between 65 and 128 bytes in length." ::= { extremeWirelessIntfFrameSizeEntry 20 } extremeWirelessIntfFrameSizeCtlRX256 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This gives the number of control-type frames received on this interface which were between 129 and 256 bytes in length." ::= { extremeWirelessIntfFrameSizeEntry 21 } extremeWirelessIntfFrameSizeCtlRX512 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This gives the number of control-type frames received on this interface which were between 257 and 512 bytes in length." ::= { extremeWirelessIntfFrameSizeEntry 22 } extremeWirelessIntfFrameSizeCtlRX1024 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This gives the number of control-type frames received on this interface which were between 513 and 1024 bytes in length." ::= { extremeWirelessIntfFrameSizeEntry 23 } extremeWirelessIntfFrameSizeCtlRX2048 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This gives the number of control-type frames received on this interface which were between 1025 and 2048 bytes in length." ::= { extremeWirelessIntfFrameSizeEntry 24 } extremeWirelessIntfFrameSizeDataTX64 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This gives the number of data-type frames transmitted on this interface which were less than or equal to 64 bytes in length." ::= { extremeWirelessIntfFrameSizeEntry 25 } extremeWirelessIntfFrameSizeDataTX128 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This gives the number of data-type frames transmitted on this interface which were between 65 and 128 bytes in length." ::= { extremeWirelessIntfFrameSizeEntry 26 } extremeWirelessIntfFrameSizeDataTX256 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This gives the number of data-type frames transmitted on this interface which were between 129 and 256 bytes in length." ::= { extremeWirelessIntfFrameSizeEntry 27 } extremeWirelessIntfFrameSizeDataTX512 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This gives the number of data-type frames transmitted on this interface which were between 257 and 512 bytes in length." ::= { extremeWirelessIntfFrameSizeEntry 28 } extremeWirelessIntfFrameSizeDataTX1024 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This gives the number of data-type frames transmitted on this interface which were between 513 and 1024 bytes in length." ::= { extremeWirelessIntfFrameSizeEntry 29 } extremeWirelessIntfFrameSizeDataTX2048 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This gives the number of data-type frames transmitted on this interface which were between 1025 and 2048 bytes in length." ::= { extremeWirelessIntfFrameSizeEntry 30 } extremeWirelessIntfFrameSizeDataRX64 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This gives the number of data-type frames received on this interface which were less than or equal to 64 bytes in length." ::= { extremeWirelessIntfFrameSizeEntry 31 } extremeWirelessIntfFrameSizeDataRX128 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This gives the number of data-type frames received on this interface which were between 65 and 128 bytes in length." ::= { extremeWirelessIntfFrameSizeEntry 32 } extremeWirelessIntfFrameSizeDataRX256 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This gives the number of data-type frames received on this interface which were between 129 and 256 bytes in length." ::= { extremeWirelessIntfFrameSizeEntry 33 } extremeWirelessIntfFrameSizeDataRX512 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This gives the number of data-type frames received on this interface which were between 257 and 512 bytes in length." ::= { extremeWirelessIntfFrameSizeEntry 34 } extremeWirelessIntfFrameSizeDataRX1024 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This gives the number of data-type frames received on this interface which were between 513 and 1024 bytes in length." ::= { extremeWirelessIntfFrameSizeEntry 35 } extremeWirelessIntfFrameSizeDataRX2048 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This gives the number of data-type frames received on this interface which were between 1025 and 2048 bytes in length." ::= { extremeWirelessIntfFrameSizeEntry 36 } -- *************************************************************** -- -- Frame errors by size. -- -- *************************************************************** -- extremeWirelessIntfFrameSizeErrorTable OBJECT-TYPE SYNTAX SEQUENCE OF ExtremeWirelessIntfFrameSizeErrorEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "There is one entry in this table for each virtual and physical interface. Values for physical interfaces are summations of the values for the constituent virtual interfaces." ::= { extremeAP 40 } extremeWirelessIntfFrameSizeErrorEntry OBJECT-TYPE SYNTAX ExtremeWirelessIntfFrameSizeErrorEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "" INDEX { ifIndex } ::= { extremeWirelessIntfFrameSizeErrorTable 1 } ExtremeWirelessIntfFrameSizeErrorEntry ::= SEQUENCE { extremeWirelessIntfFrameSizeReXmit64 Unsigned32, extremeWirelessIntfFrameSizeReXmit128 Unsigned32, extremeWirelessIntfFrameSizeReXmit256 Unsigned32, extremeWirelessIntfFrameSizeReXmit512 Unsigned32, extremeWirelessIntfFrameSizeReXmit1024 Unsigned32, extremeWirelessIntfFrameSizeReXmit2048 Unsigned32, extremeWirelessIntfFrameSizeErrorTX64 Unsigned32, extremeWirelessIntfFrameSizeErrorTX128 Unsigned32, extremeWirelessIntfFrameSizeErrorTX256 Unsigned32, extremeWirelessIntfFrameSizeErrorTX512 Unsigned32, extremeWirelessIntfFrameSizeErrorTX1024 Unsigned32, extremeWirelessIntfFrameSizeErrorTX2048 Unsigned32, extremeWirelessIntfFrameSizeErrorRX64 Unsigned32, extremeWirelessIntfFrameSizeErrorRX128 Unsigned32, extremeWirelessIntfFrameSizeErrorRX256 Unsigned32, extremeWirelessIntfFrameSizeErrorRX512 Unsigned32, extremeWirelessIntfFrameSizeErrorRX1024 Unsigned32, extremeWirelessIntfFrameSizeErrorRX2048 Unsigned32 } extremeWirelessIntfFrameSizeReXmit64 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This gives the number of frames retransmitted on this interface which were less than or equal to 64 bytes in length." ::= { extremeWirelessIntfFrameSizeErrorEntry 1 } extremeWirelessIntfFrameSizeReXmit128 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This gives the number of frames retransmitted on this interface which were between 65 and 128 bytes in length." ::= { extremeWirelessIntfFrameSizeErrorEntry 2 } extremeWirelessIntfFrameSizeReXmit256 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This gives the number of frames retransmitted on this interface which were between 129 and 256 bytes in length." ::= { extremeWirelessIntfFrameSizeErrorEntry 3 } extremeWirelessIntfFrameSizeReXmit512 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This gives the number of frames retransmitted on this interface which were between 257 and 512 bytes in length." ::= { extremeWirelessIntfFrameSizeErrorEntry 4 } extremeWirelessIntfFrameSizeReXmit1024 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This gives the number of frames retransmitted on this interface which were between 513 and 1024 bytes in length." ::= { extremeWirelessIntfFrameSizeErrorEntry 5 } extremeWirelessIntfFrameSizeReXmit2048 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This gives the number of frames retransmitted on this interface which were between 1025 and 2048 bytes in length." ::= { extremeWirelessIntfFrameSizeErrorEntry 6 } extremeWirelessIntfFrameSizeErrorTX64 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This gives the number of frames which failed to be transmitted interface which were less than or equal to 64 bytes in length." ::= { extremeWirelessIntfFrameSizeErrorEntry 7 } extremeWirelessIntfFrameSizeErrorTX128 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This gives the number of frames which failed to be transmitted interface which were between 65 and 128 bytes in length." ::= { extremeWirelessIntfFrameSizeErrorEntry 8 } extremeWirelessIntfFrameSizeErrorTX256 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This gives the number of frames which failed to be transmitted interface which were between 129 and 256 bytes in length." ::= { extremeWirelessIntfFrameSizeErrorEntry 9 } extremeWirelessIntfFrameSizeErrorTX512 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This gives the number of frames which failed to be transmitted interface which were between 257 and 512 bytes in length." ::= { extremeWirelessIntfFrameSizeErrorEntry 10 } extremeWirelessIntfFrameSizeErrorTX1024 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This gives the number of frames which failed to be transmitted interface which were between 513 and 1024 bytes in length." ::= { extremeWirelessIntfFrameSizeErrorEntry 11 } extremeWirelessIntfFrameSizeErrorTX2048 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This gives the number of frames which failed to be transmitted interface which were between 1025 and 2048 bytes in length." ::= { extremeWirelessIntfFrameSizeErrorEntry 12 } extremeWirelessIntfFrameSizeErrorRX64 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This gives the number of frames which had errors on receive on this interface which were less than or equal to 64 bytes in length." ::= { extremeWirelessIntfFrameSizeErrorEntry 13 } extremeWirelessIntfFrameSizeErrorRX128 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This gives the number of frames which had errors on receive on this interface which were between 65 and 128 bytes in length." ::= { extremeWirelessIntfFrameSizeErrorEntry 14 } extremeWirelessIntfFrameSizeErrorRX256 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This gives the number of frames which had errors on receive on this interface which were between 129 and 256 bytes in length." ::= { extremeWirelessIntfFrameSizeErrorEntry 15 } extremeWirelessIntfFrameSizeErrorRX512 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This gives the number of frames which had errors on receive on this interface which were between 257 and 512 bytes in length." ::= { extremeWirelessIntfFrameSizeErrorEntry 16 } extremeWirelessIntfFrameSizeErrorRX1024 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This gives the number of frames which had errors on receive on this interface which were between 513 and 1024 bytes in length." ::= { extremeWirelessIntfFrameSizeErrorEntry 17 } extremeWirelessIntfFrameSizeErrorRX2048 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This gives the number of frames which had errors on receive on this interface which were between 1025 and 2048 bytes in length." ::= { extremeWirelessIntfFrameSizeErrorEntry 18 } -- *************************************************************** -- -- TX/RX Histogram based on speed. -- *************************************************************** -- extremeWirelessIntfFrameSpeedTable OBJECT-TYPE SYNTAX SEQUENCE OF ExtremeWirelessIntfFrameSpeedEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "There is one entry in this table for each virtual and physical interface. Values for physical interfaces are summations of the values for the constituent virtual interfaces." ::= { extremeAP 41 } extremeWirelessIntfFrameSpeedEntry OBJECT-TYPE SYNTAX ExtremeWirelessIntfFrameSpeedEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "" INDEX { ifIndex } ::= { extremeWirelessIntfFrameSpeedTable 1 } ExtremeWirelessIntfFrameSpeedEntry ::= SEQUENCE { extremeWirelessIntfSpeedMgmtTX1 Unsigned32, extremeWirelessIntfSpeedMgmtTX2 Unsigned32, extremeWirelessIntfSpeedMgmtTX5p5 Unsigned32, extremeWirelessIntfSpeedMgmtTX6 Unsigned32, extremeWirelessIntfSpeedMgmtTX9 Unsigned32, extremeWirelessIntfSpeedMgmtTX11 Unsigned32, extremeWirelessIntfSpeedMgmtTX12 Unsigned32, extremeWirelessIntfSpeedMgmtTX18 Unsigned32, extremeWirelessIntfSpeedMgmtTX24 Unsigned32, extremeWirelessIntfSpeedMgmtTX36 Unsigned32, extremeWirelessIntfSpeedMgmtTX48 Unsigned32, extremeWirelessIntfSpeedMgmtTX54 Unsigned32, extremeWirelessIntfSpeedMgmtRX1 Unsigned32, extremeWirelessIntfSpeedMgmtRX2 Unsigned32, extremeWirelessIntfSpeedMgmtRX5p5 Unsigned32, extremeWirelessIntfSpeedMgmtRX6 Unsigned32, extremeWirelessIntfSpeedMgmtRX9 Unsigned32, extremeWirelessIntfSpeedMgmtRX11 Unsigned32, extremeWirelessIntfSpeedMgmtRX12 Unsigned32, extremeWirelessIntfSpeedMgmtRX18 Unsigned32, extremeWirelessIntfSpeedMgmtRX24 Unsigned32, extremeWirelessIntfSpeedMgmtRX36 Unsigned32, extremeWirelessIntfSpeedMgmtRX48 Unsigned32, extremeWirelessIntfSpeedMgmtRX54 Unsigned32, extremeWirelessIntfSpeedCtlTX1 Unsigned32, extremeWirelessIntfSpeedCtlTX2 Unsigned32, extremeWirelessIntfSpeedCtlTX5p5 Unsigned32, extremeWirelessIntfSpeedCtlTX6 Unsigned32, extremeWirelessIntfSpeedCtlTX9 Unsigned32, extremeWirelessIntfSpeedCtlTX11 Unsigned32, extremeWirelessIntfSpeedCtlTX12 Unsigned32, extremeWirelessIntfSpeedCtlTX18 Unsigned32, extremeWirelessIntfSpeedCtlTX24 Unsigned32, extremeWirelessIntfSpeedCtlTX36 Unsigned32, extremeWirelessIntfSpeedCtlTX48 Unsigned32, extremeWirelessIntfSpeedCtlTX54 Unsigned32, extremeWirelessIntfSpeedCtlRX1 Unsigned32, extremeWirelessIntfSpeedCtlRX2 Unsigned32, extremeWirelessIntfSpeedCtlRX5p5 Unsigned32, extremeWirelessIntfSpeedCtlRX6 Unsigned32, extremeWirelessIntfSpeedCtlRX9 Unsigned32, extremeWirelessIntfSpeedCtlRX11 Unsigned32, extremeWirelessIntfSpeedCtlRX12 Unsigned32, extremeWirelessIntfSpeedCtlRX18 Unsigned32, extremeWirelessIntfSpeedCtlRX24 Unsigned32, extremeWirelessIntfSpeedCtlRX36 Unsigned32, extremeWirelessIntfSpeedCtlRX48 Unsigned32, extremeWirelessIntfSpeedCtlRX54 Unsigned32, extremeWirelessIntfSpeedDataTX1 Unsigned32, extremeWirelessIntfSpeedDataTX2 Unsigned32, extremeWirelessIntfSpeedDataTX5p5 Unsigned32, extremeWirelessIntfSpeedDataTX6 Unsigned32, extremeWirelessIntfSpeedDataTX9 Unsigned32, extremeWirelessIntfSpeedDataTX11 Unsigned32, extremeWirelessIntfSpeedDataTX12 Unsigned32, extremeWirelessIntfSpeedDataTX18 Unsigned32, extremeWirelessIntfSpeedDataTX24 Unsigned32, extremeWirelessIntfSpeedDataTX36 Unsigned32, extremeWirelessIntfSpeedDataTX48 Unsigned32, extremeWirelessIntfSpeedDataTX54 Unsigned32, extremeWirelessIntfSpeedDataRX1 Unsigned32, extremeWirelessIntfSpeedDataRX2 Unsigned32, extremeWirelessIntfSpeedDataRX5p5 Unsigned32, extremeWirelessIntfSpeedDataRX6 Unsigned32, extremeWirelessIntfSpeedDataRX9 Unsigned32, extremeWirelessIntfSpeedDataRX11 Unsigned32, extremeWirelessIntfSpeedDataRX12 Unsigned32, extremeWirelessIntfSpeedDataRX18 Unsigned32, extremeWirelessIntfSpeedDataRX24 Unsigned32, extremeWirelessIntfSpeedDataRX36 Unsigned32, extremeWirelessIntfSpeedDataRX48 Unsigned32, extremeWirelessIntfSpeedDataRX54 Unsigned32 } extremeWirelessIntfSpeedMgmtTX1 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This gives the number of management-type frames transmitted on this interface at 1Mbps." ::= { extremeWirelessIntfFrameSpeedEntry 1 } extremeWirelessIntfSpeedMgmtTX2 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This gives the number of management-type frames transmitted on this interface at 2Mbps." ::= { extremeWirelessIntfFrameSpeedEntry 2 } extremeWirelessIntfSpeedMgmtTX5p5 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This gives the number of management-type frames transmitted on this interface at 5.5Mbps." ::= { extremeWirelessIntfFrameSpeedEntry 3 } extremeWirelessIntfSpeedMgmtTX6 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This gives the number of management-type frames transmitted on this interface at 6Mbps." ::= { extremeWirelessIntfFrameSpeedEntry 4 } extremeWirelessIntfSpeedMgmtTX9 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This gives the number of management-type frames transmitted on this interface at 9Mbps." ::= { extremeWirelessIntfFrameSpeedEntry 5 } extremeWirelessIntfSpeedMgmtTX11 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This gives the number of management-type frames transmitted on this interface at 11Mbps." ::= { extremeWirelessIntfFrameSpeedEntry 6 } extremeWirelessIntfSpeedMgmtTX12 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This gives the number of management-type frames transmitted on this interface at 12Mbps." ::= { extremeWirelessIntfFrameSpeedEntry 7 } extremeWirelessIntfSpeedMgmtTX18 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This gives the number of management-type frames transmitted on this interface at 18Mbps." ::= { extremeWirelessIntfFrameSpeedEntry 8 } extremeWirelessIntfSpeedMgmtTX24 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This gives the number of management-type frames transmitted on this interface at 24Mbps." ::= { extremeWirelessIntfFrameSpeedEntry 9 } extremeWirelessIntfSpeedMgmtTX36 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This gives the number of management-type frames transmitted on this interface at 36Mbps." ::= { extremeWirelessIntfFrameSpeedEntry 10 } extremeWirelessIntfSpeedMgmtTX48 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This gives the number of management-type frames transmitted on this interface at 48Mbps." ::= { extremeWirelessIntfFrameSpeedEntry 11 } extremeWirelessIntfSpeedMgmtTX54 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This gives the number of management-type frames transmitted on this interface at 54Mbps." ::= { extremeWirelessIntfFrameSpeedEntry 12 } extremeWirelessIntfSpeedMgmtRX1 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This gives the number of management-type frames recieved on this interface at 1Mbps." ::= { extremeWirelessIntfFrameSpeedEntry 13 } extremeWirelessIntfSpeedMgmtRX2 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This gives the number of management-type frames recieved on this interface at 2Mbps." ::= { extremeWirelessIntfFrameSpeedEntry 14 } extremeWirelessIntfSpeedMgmtRX5p5 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This gives the number of management-type frames recieved on this interface at 5.5Mbps." ::= { extremeWirelessIntfFrameSpeedEntry 15 } extremeWirelessIntfSpeedMgmtRX6 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This gives the number of management-type frames recieved on this interface at 6Mbps." ::= { extremeWirelessIntfFrameSpeedEntry 16 } extremeWirelessIntfSpeedMgmtRX9 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This gives the number of management-type frames recieved on this interface at 9Mbps." ::= { extremeWirelessIntfFrameSpeedEntry 17 } extremeWirelessIntfSpeedMgmtRX11 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This gives the number of management-type frames recieved on this interface at 11Mbps." ::= { extremeWirelessIntfFrameSpeedEntry 18 } extremeWirelessIntfSpeedMgmtRX12 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This gives the number of management-type frames recieved on this interface at 12Mbps." ::= { extremeWirelessIntfFrameSpeedEntry 19 } extremeWirelessIntfSpeedMgmtRX18 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This gives the number of management-type frames recieved on this interface at 18Mbps." ::= { extremeWirelessIntfFrameSpeedEntry 20 } extremeWirelessIntfSpeedMgmtRX24 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This gives the number of management-type frames recieved on this interface at 24Mbps." ::= { extremeWirelessIntfFrameSpeedEntry 21 } extremeWirelessIntfSpeedMgmtRX36 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This gives the number of management-type frames recieved on this interface at 36Mbps." ::= { extremeWirelessIntfFrameSpeedEntry 22 } extremeWirelessIntfSpeedMgmtRX48 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This gives the number of management-type frames recieved on this interface at 48Mbps." ::= { extremeWirelessIntfFrameSpeedEntry 23 } extremeWirelessIntfSpeedMgmtRX54 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This gives the number of management-type frames recieved on this interface at 54Mbps." ::= { extremeWirelessIntfFrameSpeedEntry 24 } extremeWirelessIntfSpeedCtlTX1 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This gives the number of control-type frames transmitted on this interface at 1Mbps." ::= { extremeWirelessIntfFrameSpeedEntry 25 } extremeWirelessIntfSpeedCtlTX2 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This gives the number of control-type frames transmitted on this interface at 2Mbps." ::= { extremeWirelessIntfFrameSpeedEntry 26 } extremeWirelessIntfSpeedCtlTX5p5 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This gives the number of control-type frames transmitted on this interface at 5.5Mbps." ::= { extremeWirelessIntfFrameSpeedEntry 27 } extremeWirelessIntfSpeedCtlTX6 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This gives the number of control-type frames transmitted on this interface at 6Mbps." ::= { extremeWirelessIntfFrameSpeedEntry 28 } extremeWirelessIntfSpeedCtlTX9 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This gives the number of control-type frames transmitted on this interface at 9Mbps." ::= { extremeWirelessIntfFrameSpeedEntry 29 } extremeWirelessIntfSpeedCtlTX11 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This gives the number of control-type frames transmitted on this interface at 11Mbps." ::= { extremeWirelessIntfFrameSpeedEntry 30 } extremeWirelessIntfSpeedCtlTX12 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This gives the number of control-type frames transmitted on this interface at 12Mbps." ::= { extremeWirelessIntfFrameSpeedEntry 31 } extremeWirelessIntfSpeedCtlTX18 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This gives the number of control-type frames transmitted on this interface at 18Mbps." ::= { extremeWirelessIntfFrameSpeedEntry 32 } extremeWirelessIntfSpeedCtlTX24 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This gives the number of control-type frames transmitted on this interface at 24Mbps." ::= { extremeWirelessIntfFrameSpeedEntry 33 } extremeWirelessIntfSpeedCtlTX36 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This gives the number of control-type frames transmitted on this interface at 36Mbps." ::= { extremeWirelessIntfFrameSpeedEntry 34 } extremeWirelessIntfSpeedCtlTX48 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This gives the number of control-type frames transmitted on this interface at 48Mbps." ::= { extremeWirelessIntfFrameSpeedEntry 35 } extremeWirelessIntfSpeedCtlTX54 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This gives the number of control-type frames transmitted on this interface at 54Mbps." ::= { extremeWirelessIntfFrameSpeedEntry 36 } extremeWirelessIntfSpeedCtlRX1 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This gives the number of control-type frames recieved on this interface at 1Mbps." ::= { extremeWirelessIntfFrameSpeedEntry 37 } extremeWirelessIntfSpeedCtlRX2 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This gives the number of control-type frames recieved on this interface at 2Mbps." ::= { extremeWirelessIntfFrameSpeedEntry 38 } extremeWirelessIntfSpeedCtlRX5p5 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This gives the number of control-type frames recieved on this interface at 5.5Mbps." ::= { extremeWirelessIntfFrameSpeedEntry 39 } extremeWirelessIntfSpeedCtlRX6 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This gives the number of control-type frames recieved on this interface at 6Mbps." ::= { extremeWirelessIntfFrameSpeedEntry 40 } extremeWirelessIntfSpeedCtlRX9 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This gives the number of control-type frames recieved on this interface at 9Mbps." ::= { extremeWirelessIntfFrameSpeedEntry 41 } extremeWirelessIntfSpeedCtlRX11 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This gives the number of control-type frames recieved on this interface at 11Mbps." ::= { extremeWirelessIntfFrameSpeedEntry 42 } extremeWirelessIntfSpeedCtlRX12 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This gives the number of control-type frames recieved on this interface at 12Mbps." ::= { extremeWirelessIntfFrameSpeedEntry 43 } extremeWirelessIntfSpeedCtlRX18 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This gives the number of control-type frames recieved on this interface at 18Mbps." ::= { extremeWirelessIntfFrameSpeedEntry 44 } extremeWirelessIntfSpeedCtlRX24 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This gives the number of control-type frames recieved on this interface at 24Mbps." ::= { extremeWirelessIntfFrameSpeedEntry 45 } extremeWirelessIntfSpeedCtlRX36 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This gives the number of control-type frames recieved on this interface at 36Mbps." ::= { extremeWirelessIntfFrameSpeedEntry 46 } extremeWirelessIntfSpeedCtlRX48 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This gives the number of control-type frames recieved on this interface at 48Mbps." ::= { extremeWirelessIntfFrameSpeedEntry 47 } extremeWirelessIntfSpeedCtlRX54 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This gives the number of control-type frames recieved on this interface at 54Mbps." ::= { extremeWirelessIntfFrameSpeedEntry 48 } extremeWirelessIntfSpeedDataTX1 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This gives the number of data-type frames transmitted on this interface at 1Mbps." ::= { extremeWirelessIntfFrameSpeedEntry 49 } extremeWirelessIntfSpeedDataTX2 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This gives the number of data-type frames transmitted on this interface at 2Mbps." ::= { extremeWirelessIntfFrameSpeedEntry 50 } extremeWirelessIntfSpeedDataTX5p5 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This gives the number of data-type frames transmitted on this interface at 5.5Mbps." ::= { extremeWirelessIntfFrameSpeedEntry 51 } extremeWirelessIntfSpeedDataTX6 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This gives the number of data-type frames transmitted on this interface at 6Mbps." ::= { extremeWirelessIntfFrameSpeedEntry 52 } extremeWirelessIntfSpeedDataTX9 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This gives the number of data-type frames transmitted on this interface at 9Mbps." ::= { extremeWirelessIntfFrameSpeedEntry 53 } extremeWirelessIntfSpeedDataTX11 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This gives the number of data-type frames transmitted on this interface at 11Mbps." ::= { extremeWirelessIntfFrameSpeedEntry 54 } extremeWirelessIntfSpeedDataTX12 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This gives the number of data-type frames transmitted on this interface at 12Mbps." ::= { extremeWirelessIntfFrameSpeedEntry 55 } extremeWirelessIntfSpeedDataTX18 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This gives the number of data-type frames transmitted on this interface at 18Mbps." ::= { extremeWirelessIntfFrameSpeedEntry 56 } extremeWirelessIntfSpeedDataTX24 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This gives the number of data-type frames transmitted on this interface at 24Mbps." ::= { extremeWirelessIntfFrameSpeedEntry 57 } extremeWirelessIntfSpeedDataTX36 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This gives the number of data-type frames transmitted on this interface at 36Mbps." ::= { extremeWirelessIntfFrameSpeedEntry 58 } extremeWirelessIntfSpeedDataTX48 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This gives the number of data-type frames transmitted on this interface at 48Mbps." ::= { extremeWirelessIntfFrameSpeedEntry 59 } extremeWirelessIntfSpeedDataTX54 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This gives the number of data-type frames transmitted on this interface at 54Mbps." ::= { extremeWirelessIntfFrameSpeedEntry 60 } extremeWirelessIntfSpeedDataRX1 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This gives the number of data-type frames recieved on this interface at 1Mbps." ::= { extremeWirelessIntfFrameSpeedEntry 61 } extremeWirelessIntfSpeedDataRX2 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This gives the number of data-type frames recieved on this interface at 2Mbps." ::= { extremeWirelessIntfFrameSpeedEntry 62 } extremeWirelessIntfSpeedDataRX5p5 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This gives the number of data-type frames recieved on this interface at 5.5Mbps." ::= { extremeWirelessIntfFrameSpeedEntry 63 } extremeWirelessIntfSpeedDataRX6 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This gives the number of data-type frames recieved on this interface at 6Mbps." ::= { extremeWirelessIntfFrameSpeedEntry 64 } extremeWirelessIntfSpeedDataRX9 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This gives the number of data-type frames recieved on this interface at 9Mbps." ::= { extremeWirelessIntfFrameSpeedEntry 65 } extremeWirelessIntfSpeedDataRX11 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This gives the number of data-type frames recieved on this interface at 11Mbps." ::= { extremeWirelessIntfFrameSpeedEntry 66 } extremeWirelessIntfSpeedDataRX12 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This gives the number of data-type frames recieved on this interface at 12Mbps." ::= { extremeWirelessIntfFrameSpeedEntry 67 } extremeWirelessIntfSpeedDataRX18 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This gives the number of data-type frames recieved on this interface at 18Mbps." ::= { extremeWirelessIntfFrameSpeedEntry 68 } extremeWirelessIntfSpeedDataRX24 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This gives the number of data-type frames recieved on this interface at 24Mbps." ::= { extremeWirelessIntfFrameSpeedEntry 69 } extremeWirelessIntfSpeedDataRX36 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This gives the number of data-type frames recieved on this interface at 36Mbps." ::= { extremeWirelessIntfFrameSpeedEntry 70 } extremeWirelessIntfSpeedDataRX48 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This gives the number of data-type frames recieved on this interface at 48Mbps." ::= { extremeWirelessIntfFrameSpeedEntry 71 } extremeWirelessIntfSpeedDataRX54 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This gives the number of data-type frames recieved on this interface at 54Mbps." ::= { extremeWirelessIntfFrameSpeedEntry 72 } -- *************************************************************** -- -- Error Histograms of retransmission by frame speed. -- -- *************************************************************** -- extremeWirelessIntfFrameSpeedErrorTable OBJECT-TYPE SYNTAX SEQUENCE OF ExtremeWirelessIntfFrameSpeedErrorEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "There is one entry in this table for each virtual and physical interface. Values for physical interfaces are summations of the values for the constituent virtual interfaces." ::= { extremeAP 42 } extremeWirelessIntfFrameSpeedErrorEntry OBJECT-TYPE SYNTAX ExtremeWirelessIntfFrameSpeedErrorEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "" INDEX { ifIndex } ::= { extremeWirelessIntfFrameSpeedErrorTable 1 } ExtremeWirelessIntfFrameSpeedErrorEntry ::= SEQUENCE { extremeWirelessIntfSpeedReXmit1 Unsigned32, extremeWirelessIntfSpeedReXmit2 Unsigned32, extremeWirelessIntfSpeedReXmit5p5 Unsigned32, extremeWirelessIntfSpeedReXmit6 Unsigned32, extremeWirelessIntfSpeedReXmit9 Unsigned32, extremeWirelessIntfSpeedReXmit11 Unsigned32, extremeWirelessIntfSpeedReXmit12 Unsigned32, extremeWirelessIntfSpeedReXmit18 Unsigned32, extremeWirelessIntfSpeedReXmit24 Unsigned32, extremeWirelessIntfSpeedReXmit36 Unsigned32, extremeWirelessIntfSpeedReXmit48 Unsigned32, extremeWirelessIntfSpeedReXmit54 Unsigned32, extremeWirelessIntfSpeedErrorTX1 Unsigned32, extremeWirelessIntfSpeedErrorTX2 Unsigned32, extremeWirelessIntfSpeedErrorTX5p5 Unsigned32, extremeWirelessIntfSpeedErrorTX6 Unsigned32, extremeWirelessIntfSpeedErrorTX9 Unsigned32, extremeWirelessIntfSpeedErrorTX11 Unsigned32, extremeWirelessIntfSpeedErrorTX12 Unsigned32, extremeWirelessIntfSpeedErrorTX18 Unsigned32, extremeWirelessIntfSpeedErrorTX24 Unsigned32, extremeWirelessIntfSpeedErrorTX36 Unsigned32, extremeWirelessIntfSpeedErrorTX48 Unsigned32, extremeWirelessIntfSpeedErrorTX54 Unsigned32, extremeWirelessIntfSpeedErrorRX1 Unsigned32, extremeWirelessIntfSpeedErrorRX2 Unsigned32, extremeWirelessIntfSpeedErrorRX5p5 Unsigned32, extremeWirelessIntfSpeedErrorRX6 Unsigned32, extremeWirelessIntfSpeedErrorRX9 Unsigned32, extremeWirelessIntfSpeedErrorRX11 Unsigned32, extremeWirelessIntfSpeedErrorRX12 Unsigned32, extremeWirelessIntfSpeedErrorRX18 Unsigned32, extremeWirelessIntfSpeedErrorRX24 Unsigned32, extremeWirelessIntfSpeedErrorRX36 Unsigned32, extremeWirelessIntfSpeedErrorRX48 Unsigned32, extremeWirelessIntfSpeedErrorRX54 Unsigned32 } extremeWirelessIntfSpeedReXmit1 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This gives the number of frames which were retransmitted on this interface at 1 Mbps." ::= { extremeWirelessIntfFrameSpeedErrorEntry 1 } extremeWirelessIntfSpeedReXmit2 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This gives the number of frames which were retransmitted on this interface at 2 Mbps." ::= { extremeWirelessIntfFrameSpeedErrorEntry 2 } extremeWirelessIntfSpeedReXmit5p5 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This gives the number of frames which were retransmitted on this interface at 5 Mbps." ::= { extremeWirelessIntfFrameSpeedErrorEntry 3 } extremeWirelessIntfSpeedReXmit6 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This gives the number of frames which were retransmitted on this interface at 6 Mbps." ::= { extremeWirelessIntfFrameSpeedErrorEntry 4 } extremeWirelessIntfSpeedReXmit9 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This gives the number of frames which were retransmitted on this interface at 9 Mbps." ::= { extremeWirelessIntfFrameSpeedErrorEntry 5 } extremeWirelessIntfSpeedReXmit11 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This gives the number of frames which were retransmitted on this interface at 11 Mbps." ::= { extremeWirelessIntfFrameSpeedErrorEntry 6 } extremeWirelessIntfSpeedReXmit12 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This gives the number of frames which were retransmitted on this interface at 12 Mbps." ::= { extremeWirelessIntfFrameSpeedErrorEntry 7 } extremeWirelessIntfSpeedReXmit18 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This gives the number of frames which were retransmitted on this interface at 18 Mbps." ::= { extremeWirelessIntfFrameSpeedErrorEntry 8 } extremeWirelessIntfSpeedReXmit24 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This gives the number of frames which were retransmitted on this interface at 24 Mbps." ::= { extremeWirelessIntfFrameSpeedErrorEntry 9 } extremeWirelessIntfSpeedReXmit36 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This gives the number of frames which were retransmitted on this interface at 36 Mbps." ::= { extremeWirelessIntfFrameSpeedErrorEntry 10 } extremeWirelessIntfSpeedReXmit48 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This gives the number of frames which were retransmitted on this interface at 48 Mbps." ::= { extremeWirelessIntfFrameSpeedErrorEntry 11 } extremeWirelessIntfSpeedReXmit54 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This gives the number of frames which were retransmitted on this interface at 54 Mbps." ::= { extremeWirelessIntfFrameSpeedErrorEntry 12 } extremeWirelessIntfSpeedErrorTX1 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This gives the number of frames which were transmited with errors on this interface at 1Mbps." ::= { extremeWirelessIntfFrameSpeedErrorEntry 13 } extremeWirelessIntfSpeedErrorTX2 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This gives the number of frames which were transmited with errors on this interface at 2Mbps." ::= { extremeWirelessIntfFrameSpeedErrorEntry 14 } extremeWirelessIntfSpeedErrorTX5p5 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This gives the number of frames which were transmited with errors on this interface at 5.5Mbps." ::= { extremeWirelessIntfFrameSpeedErrorEntry 15 } extremeWirelessIntfSpeedErrorTX6 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This gives the number of frames which were transmited with errors on this interface at 6Mbps." ::= { extremeWirelessIntfFrameSpeedErrorEntry 16 } extremeWirelessIntfSpeedErrorTX9 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This gives the number of frames which were transmited with errors on this interface at 9Mbps." ::= { extremeWirelessIntfFrameSpeedErrorEntry 17 } extremeWirelessIntfSpeedErrorTX11 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This gives the number of frames which were transmited with errors on this interface at 11Mbps." ::= { extremeWirelessIntfFrameSpeedErrorEntry 18 } extremeWirelessIntfSpeedErrorTX12 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This gives the number of frames which were transmited with errors on this interface at 12Mbps." ::= { extremeWirelessIntfFrameSpeedErrorEntry 19 } extremeWirelessIntfSpeedErrorTX18 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This gives the number of frames which were transmited with errors on this interface at 18Mbps." ::= { extremeWirelessIntfFrameSpeedErrorEntry 20 } extremeWirelessIntfSpeedErrorTX24 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This gives the number of frames which were transmited with errors on this interface at 24Mbps." ::= { extremeWirelessIntfFrameSpeedErrorEntry 21 } extremeWirelessIntfSpeedErrorTX36 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This gives the number of frames which were transmited with errors on this interface at 36Mbps." ::= { extremeWirelessIntfFrameSpeedErrorEntry 22 } extremeWirelessIntfSpeedErrorTX48 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This gives the number of frames which were transmited with errors on this interface at 48Mbps." ::= { extremeWirelessIntfFrameSpeedErrorEntry 23 } extremeWirelessIntfSpeedErrorTX54 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This gives the number of frames which were transmited with errors on this interface at 54Mbps." ::= { extremeWirelessIntfFrameSpeedErrorEntry 24 } extremeWirelessIntfSpeedErrorRX1 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This gives the number of frames which were received with errors on this interface at 1Mbps." ::= { extremeWirelessIntfFrameSpeedErrorEntry 25 } extremeWirelessIntfSpeedErrorRX2 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This gives the number of frames which were received with errors on this interface at 2Mbps." ::= { extremeWirelessIntfFrameSpeedErrorEntry 26 } extremeWirelessIntfSpeedErrorRX5p5 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This gives the number of frames which were received with errors on this interface at 5.5Mbps." ::= { extremeWirelessIntfFrameSpeedErrorEntry 27 } extremeWirelessIntfSpeedErrorRX6 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This gives the number of frames which were received with errors on this interface at 6Mbps." ::= { extremeWirelessIntfFrameSpeedErrorEntry 28 } extremeWirelessIntfSpeedErrorRX9 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This gives the number of frames which were received with errors on this interface at 9Mbps." ::= { extremeWirelessIntfFrameSpeedErrorEntry 29 } extremeWirelessIntfSpeedErrorRX11 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This gives the number of frames which were received with errors on this interface at 11Mbps." ::= { extremeWirelessIntfFrameSpeedErrorEntry 30 } extremeWirelessIntfSpeedErrorRX12 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This gives the number of frames which were received with errors on this interface at 12Mbps." ::= { extremeWirelessIntfFrameSpeedErrorEntry 31 } extremeWirelessIntfSpeedErrorRX18 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This gives the number of frames which were received with errors on this interface at 18Mbps." ::= { extremeWirelessIntfFrameSpeedErrorEntry 32 } extremeWirelessIntfSpeedErrorRX24 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This gives the number of frames which were received with errors on this interface at 24Mbps." ::= { extremeWirelessIntfFrameSpeedErrorEntry 33 } extremeWirelessIntfSpeedErrorRX36 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This gives the number of frames which were received with errors on this interface at 36Mbps." ::= { extremeWirelessIntfFrameSpeedErrorEntry 34 } extremeWirelessIntfSpeedErrorRX48 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This gives the number of frames which were received with errors on this interface at 48Mbps." ::= { extremeWirelessIntfFrameSpeedErrorEntry 35 } extremeWirelessIntfSpeedErrorRX54 OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This gives the number of frames which were received with errors on this interface at 54Mbps." ::= { extremeWirelessIntfFrameSpeedErrorEntry 36 } -- *************************************************************** -- -- Interface utilization/noise. -- -- *************************************************************** -- extremeWirelessIntfUtilizationTable OBJECT-TYPE SYNTAX SEQUENCE OF ExtremeWirelessIntfUtilizationEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "There is one entry in this table for each virtual and physical interface. Values for physical interfaces are summations of the values for the constituent virtual interfaces." ::= { extremeAP 43 } extremeWirelessIntfUtilizationEntry OBJECT-TYPE SYNTAX ExtremeWirelessIntfUtilizationEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "" INDEX { ifIndex } ::= { extremeWirelessIntfUtilizationTable 1 } ExtremeWirelessIntfUtilizationEntry ::= SEQUENCE { extremeWirelessIntfUtilizationNav Unsigned32, extremeWirelessIntfUtilizationNoiseFloor Unsigned32 } extremeWirelessIntfUtilizationNav OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This gives the instantaneous NAV value on this interface, or some increasing-metric of utilization." ::= { extremeWirelessIntfUtilizationEntry 1 } extremeWirelessIntfUtilizationNoiseFloor OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This gives the noise floor in dBm for this interface." ::= { extremeWirelessIntfUtilizationEntry 2 } -- *************************************************************** -- -- Opaque client MIBs. These mibs are provided as a performance -- -- gain for the LAC management of the switch. -- -- -- -- Some of the items in this table are encoded as a series of TLVs.-- -- In this case, they are encoded as: -- -- -- -- | Type (8 bits) | length (8 bits) | value (variable) | -- -- -- -- type - equal to the index field of the element -- -- in the table this value corresponds to. -- -- -- -- length - equal to the length in bytes of the value -- -- -- -- value - this is the value. Integer value are NBO, -- -- strings are non-null terminated ASCII. -- -- -- -- *************************************************************** -- extremeWirelessOpaqueTable OBJECT-TYPE SYNTAX SEQUENCE OF ExtremeWirelessOpaqueEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION " " ::= { extremeAP 99 } extremeWirelessOpaqueEntry OBJECT-TYPE SYNTAX ExtremeWirelessOpaqueEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION " " INDEX { ifIndex } ::= { extremeWirelessOpaqueTable 1 } ExtremeWirelessOpaqueEntry ::= SEQUENCE { extremeWirelessClientData OCTET STRING, extremeWirelessPAEStatsData OCTET STRING, extremeWirelessPAEDiagData OCTET STRING, extremeWirelessScanResultsData OCTET STRING, extremeWirelessProbeInfoData OCTET STRING, extremeWirelessClientDiagData OCTET STRING, extremeWirelessClientAssocData OCTET STRING, extremeWirelessClientAuthData OCTET STRING, extremeWirelessClientMACInfoData OCTET STRING, extremeWirelessSizeCounterData OCTET STRING, extremeWirelessSpeedCounterData OCTET STRING } extremeWirelessClientData OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-only STATUS current DESCRIPTION "" ::= { extremeWirelessOpaqueEntry 1 } extremeWirelessPAEStatsData OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-only STATUS current DESCRIPTION "" ::= { extremeWirelessOpaqueEntry 2 } extremeWirelessPAEDiagData OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-only STATUS current DESCRIPTION "" ::= { extremeWirelessOpaqueEntry 3 } extremeWirelessScanResultsData OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-only STATUS current DESCRIPTION "This is the contents of the scan results table encoded as a series of TLVs." ::= { extremeWirelessOpaqueEntry 4 } extremeWirelessProbeInfoData OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-only STATUS current DESCRIPTION "This is the contents of the probe info table encoded as a series of TLVs. Each item is encoded as the entry above." ::= { extremeWirelessOpaqueEntry 5 } extremeWirelessClientDiagData OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-only STATUS current DESCRIPTION "This is the contents of the client diag table encoded as a series of TLVs. Each item is encoded as the entry above." ::= { extremeWirelessOpaqueEntry 6 } extremeWirelessClientAssocData OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-only STATUS current DESCRIPTION "This is the contents of the client assoc table encoded as a series of TLVs. Each item is encoded as the entry above. Note that since the MAC address is not a member of the table (it is an index) it will be encoded as type = 0." ::= { extremeWirelessOpaqueEntry 7 } extremeWirelessClientAuthData OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-only STATUS current DESCRIPTION "This is the contents of the client auth table encoded as a series of TLVs. Each item is encoded as the entry above. Note that since the MAC address is not a member of the table (it is an index) it will be encoded as type = 0." ::= { extremeWirelessOpaqueEntry 8 } extremeWirelessClientMACInfoData OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-only STATUS current DESCRIPTION "This is the contents of the client MAC info table encoded as a series of TLVs. Each item is encoded as the entry above. Note that since the MAC address is not a member of the table (it is an index) it will be encoded as type = 0." ::= { extremeWirelessOpaqueEntry 9 } extremeWirelessSizeCounterData OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-only STATUS current DESCRIPTION "This is the contents of the client size counter table encoded as a series of TLVs. Each item is encoded as the entry above. Note that since the MAC address is not a member of the table (it is an index) it will be encoded as type = 0." ::= { extremeWirelessOpaqueEntry 10 } extremeWirelessSpeedCounterData OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-only STATUS current DESCRIPTION "This is the contents of the client speed counter table encoded as a series of TLVs. Each item is encoded as the entry above. Note that since the MAC address is not a member of the table (it is an index) it will be encoded as type = 0." ::= { extremeWirelessOpaqueEntry 11 } -- *************************************************************** -- -- TRACE MIBS -- -- -- -- These mibs are provided on a per-wireless port basis to support -- -- configurable tracing. Each subsystem associated with a -- -- wireless port has an entry in the trace module table. These -- -- entries allow for configuration of the current trace level. -- -- statistics on each modules tracing output are also kept. At -- -- a global level several statistics are available from the trace -- -- table. -- -- *************************************************************** -- extremeWirelessTraceTable OBJECT-TYPE SYNTAX SEQUENCE OF ExtremeWirelessTraceTableEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains one entry per wireless port. This allows access to various stastics about the tracing mod -- ule on that wireless port." ::= { extremeAP 100 } extremeWirelessTraceEntry OBJECT-TYPE SYNTAX ExtremeWirelessTraceTableEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "" INDEX { ifIndex } ::= { extremeWirelessTraceTable 1 } ExtremeWirelessTraceTableEntry ::= SEQUENCE { extremeWirelessTraceMsgsOut INTEGER, extremeWirelessTraceBytesOut INTEGER, extremeWirelessTraceSuppressed INTEGER, extremeWirelessTraceOtherErr INTEGER, extremeWirelessTraceOpaque OCTET STRING } extremeWirelessTraceMsgsOut OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "This gives the number of trace messages the system has sent out to the syslog server. Suppressed messages are not counted toward this total." ::= { extremeWirelessTraceEntry 1 } extremeWirelessTraceBytesOut OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "This give the number of bytes total sent out by the trace system. This is a simple sum of the string lengths of all messages sent out." ::= { extremeWirelessTraceEntry 2 } extremeWirelessTraceSuppressed OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "This variable is incremented whenever a message is not sent out because the trace level of that system is lower than the message level." ::= { extremeWirelessTraceEntry 3 } extremeWirelessTraceOtherErr OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "This variable is incremented when a message is not sent out due to internal errors (i.e. out of memory)." ::= { extremeWirelessTraceEntry 4 } extremeWirelessTraceOpaque OBJECT-TYPE SYNTAX OCTET STRING MAX-ACCESS read-only STATUS current DESCRIPTION "This is the opaque representation of the module table to optimize retreival." ::= { extremeWirelessTraceEntry 5 } extremeWirelessTraceModuleTable OBJECT-TYPE SYNTAX SEQUENCE OF ExtremeWirelessTraceModuleEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains one entry per trace module. Each entry is indexed by an arbitrary integer value." ::= { extremeAP 101 } extremeWirelessTraceModuleEntry OBJECT-TYPE SYNTAX ExtremeWirelessTraceModuleEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "" INDEX { ifIndex, extremeWirelessTraceModuleId } ::= { extremeWirelessTraceModuleTable 1 } ExtremeWirelessTraceModuleEntry ::= SEQUENCE { extremeWirelessTraceModuleId INTEGER, extremeWirelessTraceModuleDesc DisplayString, extremeWirelessTraceModuleHeader DisplayString, extremeWirelessTraceModuleLevel INTEGER, extremeWirelessTraceModuleSuppressed INTEGER, extremeWirelessTraceModuleMsgsOut INTEGER, extremeWirelessTraceModuleBytesOut INTEGER } extremeWirelessTraceModuleId OBJECT-TYPE SYNTAX INTEGER(0..65535) MAX-ACCESS not-accessible STATUS current DESCRIPTION "This is an arbitrary integer index which is assigned to each trace module." ::= { extremeWirelessTraceModuleEntry 1 } extremeWirelessTraceModuleDesc OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "This is a string which briefly describes the purpose of this debug trace. It may include whitespace. An example is: 802.1x State Machine" ::= { extremeWirelessTraceModuleEntry 2 } extremeWirelessTraceModuleHeader OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "This is a string which is prepended to the syslog messages sent out by this debug level. It is short (5-6 characters) and does not contain white space. (i.e. DOT1X)" ::= { extremeWirelessTraceModuleEntry 3 } extremeWirelessTraceModuleLevel OBJECT-TYPE SYNTAX INTEGER(0..5) MAX-ACCESS read-write STATUS current DESCRIPTION "This value is the current debug level for this module. A lower value indicates that fewer messages will be generated by the component. A write on this value will update the current debug level." ::= { extremeWirelessTraceModuleEntry 4 } extremeWirelessTraceModuleSuppressed OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "This value indicates the number of messages logged by this module which have not been sent out because the current log level is less than the level at which the message should be logged." ::= { extremeWirelessTraceModuleEntry 5 } extremeWirelessTraceModuleMsgsOut OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "This value indicates the number messages which have been logged by this component." ::= { extremeWirelessTraceModuleEntry 6 } extremeWirelessTraceModuleBytesOut OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "This value indicates the number of bytes which have been logged by this component. This count includes the header specified in extremeWirelessTraceModuleHeader." ::= { extremeWirelessTraceModuleEntry 7 } -- *************************************************************** -- -- Log Diagnostic Counters -- -- -- -- The logging subsystem uses the following division : the event -- -- logging system recieves all messages. These message are then -- -- passed to the syslog facility for remote logging, and then msgs -- -- may be stored in the NVRAM in the case where the log level is -- -- greater than the log threshold. -- -- *************************************************************** -- extremeWirelessLogDiagTable OBJECT-TYPE SYNTAX SEQUENCE OF ExtremeWirelessLogDiagEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains counters per-log level for the event log, syslog and NVRAM subsystems for logging." ::= { extremeAP 102 } extremeWirelessLogDiagEntry OBJECT-TYPE SYNTAX ExtremeWirelessLogDiagEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "There is one entry in this table per physical port." INDEX { ifIndex } ::= { extremeWirelessLogDiagTable 1 } ExtremeWirelessLogDiagEntry ::= SEQUENCE { extremeWirelessLogDiagEventLogTotalCount Unsigned32, extremeWirelessLogDiagEventLogTotalEmergCount Unsigned32, extremeWirelessLogDiagEventLogTotalAlertCount Unsigned32, extremeWirelessLogDiagEventLogTotalCritCount Unsigned32, extremeWirelessLogDiagEventLogTotalErrorCount Unsigned32, extremeWirelessLogDiagEventLogTotalWarnCount Unsigned32, extremeWirelessLogDiagEventLogTotalNoticeCount Unsigned32, extremeWirelessLogDiagEventLogTotalInfoCount Unsigned32, extremeWirelessLogDiagEventLogTotalDebugCount Unsigned32, extremeWirelessLogDiagEventLogTotalSuppressedCount Unsigned32, extremeWirelessLogDiagEventLogTotalByteCount Unsigned32, extremeWirelessLogDiagSyslogTotalEventCount Unsigned32, extremeWirelessLogDiagSyslogTotalSuppressedCount Unsigned32, extremeWirelessLogDiagSyslogTotalByteCount Unsigned32, extremeWirelessLogDiagNVRAMTotalEventCount Unsigned32, extremeWirelessLogDiagNVRAMTotalSuppressedCount Unsigned32, extremeWirelessLogDiagNVRAMTotalDroppedCount Unsigned32, extremeWirelessLogDiagNVRAMTotalByteCount Unsigned32, extremeWirelessLogDiagClearStats TruthValue } extremeWirelessLogDiagEventLogTotalCount OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This gives the total number of messages logged since the last time the statistics were cleared." ::= { extremeWirelessLogDiagEntry 1 } extremeWirelessLogDiagEventLogTotalEmergCount OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This gives the total number of messages logged at the EMERG level." ::= { extremeWirelessLogDiagEntry 2 } extremeWirelessLogDiagEventLogTotalAlertCount OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This gives the total number of messages logged at the ALERT level." ::= { extremeWirelessLogDiagEntry 3 } extremeWirelessLogDiagEventLogTotalCritCount OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This gives the total number of messages logged at the CRIT level." ::= { extremeWirelessLogDiagEntry 4 } extremeWirelessLogDiagEventLogTotalErrorCount OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This gives the total number of messages logged at the ERROR level." ::= { extremeWirelessLogDiagEntry 5 } extremeWirelessLogDiagEventLogTotalWarnCount OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This gives the total number of messages logged at the WARN level." ::= { extremeWirelessLogDiagEntry 6 } extremeWirelessLogDiagEventLogTotalNoticeCount OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This gives the total number of messages logged at the NOTICE level." ::= { extremeWirelessLogDiagEntry 7 } extremeWirelessLogDiagEventLogTotalInfoCount OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This gives the total number of messages logged at the INFO level." ::= { extremeWirelessLogDiagEntry 8 } extremeWirelessLogDiagEventLogTotalDebugCount OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This gives the total number of messages logged at the DEBUG level." ::= { extremeWirelessLogDiagEntry 9 } extremeWirelessLogDiagEventLogTotalSuppressedCount OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This gives the total number of messages which were suppressed due to log level." ::= { extremeWirelessLogDiagEntry 10 } extremeWirelessLogDiagEventLogTotalByteCount OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This gives the total number of bytes logged by the logging subsystem." ::= { extremeWirelessLogDiagEntry 11 } extremeWirelessLogDiagSyslogTotalEventCount OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This gives the total number of messages which have been sent out to remote syslog servers." ::= { extremeWirelessLogDiagEntry 12 } extremeWirelessLogDiagSyslogTotalSuppressedCount OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This gives the total number of syslog messages which have been suppressed due to log level." ::= { extremeWirelessLogDiagEntry 13 } extremeWirelessLogDiagSyslogTotalByteCount OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This gives the total number of bytes of syslog messages which have been logged." ::= { extremeWirelessLogDiagEntry 14 } extremeWirelessLogDiagNVRAMTotalEventCount OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "Total number of messages which have been logged to NVRAM." ::= { extremeWirelessLogDiagEntry 15 } extremeWirelessLogDiagNVRAMTotalSuppressedCount OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "Total number of messages which have been suppressed by NVRAM due to NVRAM threashold." ::= { extremeWirelessLogDiagEntry 16 } extremeWirelessLogDiagNVRAMTotalDroppedCount OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "Total number of messages which have been dropped by the NVRAM." ::= { extremeWirelessLogDiagEntry 17 } extremeWirelessLogDiagNVRAMTotalByteCount OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "Total number of bytes which have been written to the NVRAM." ::= { extremeWirelessLogDiagEntry 18 } extremeWirelessLogDiagClearStats OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "Setting this value to TRUE causes the statistics to be reset to 0. Reading this value has no meaning." ::= { extremeWirelessLogDiagEntry 19 } -- *************************************************************** -- -- TRAPS -- -- -- -- NOTE: We define client Authentication and association traps but -- -- performance may dictate that this not be done. In that -- -- case we have already provided the Authentication and -- -- association totals which can be watched from RMON. -- -- -- -- NOTE: The MAP State Change trap is not sent when the MAP is -- -- first discovered. The first trap is sent by EDP. -- -- *************************************************************** -- extremeWirelessPortStateChange NOTIFICATION-TYPE OBJECTS { ifIndex, extremeWirelessPortState } STATUS current DESCRIPTION "This trap is generated when a wireless port moves into enabled, disabled or online." ::= { extremeAPTrapsPrefix 1 } extremeWirelessPortBootFailure NOTIFICATION-TYPE OBJECTS { extremeWirelessPortIfIndex } STATUS current DESCRIPTION "This trap is sent by the platform if a wireless port fails to boot too many times." ::= { extremeAPTrapsPrefix 2 } extremeWirelessClientStationAgedOut NOTIFICATION-TYPE OBJECTS { ifIndex, extremeWirelessClientID } STATUS current DESCRIPTION "This trap is generated when a client is aged out of the table." ::= { extremeAPTrapsPrefix 3 } extremeWirelessNetloginClientAssociated NOTIFICATION-TYPE OBJECTS { ifIndex, extremeWirelessClientID } STATUS current DESCRIPTION "This trap is generated when a client has associated to an interface that is web based network login enabled." ::= { extremeAPTrapsPrefix 4 } extremeWirelessAPAdded NOTIFICATION-TYPE OBJECTS { ifIndex, extremeWirelessScanResultsStationId, extremeWirelessScanResultsFirstSeen, extremeWirelessScanResultsLastChange, extremeWirelessScanResultsPacketRate, extremeWirelessScanResultsChannel, extremeWirelessScanResultsAvgRSS, extremeWirelessScanResultsSSID, extremeWirelessScanResultsRSNEnabled, extremeWirelessScanResultsPrivacy, extremeWirelessScanResultsNetworkType, extremeWirelessScanWPAIEMcastCipher, extremeWirelessScanWPAUcastCipherCount, extremeWirelessScanWPAUcastCipher, extremeWirelessScanWPAKeyMgmtCount, extremeWirelessScanWPAKeyMgmtSuite, extremeWirelessScanResultsRateSet, extremeWirelessScanResultsExtRateSet } STATUS current DESCRIPTION "This is generated when a new AP is added to the scan results table. It will ony be generated if the value of extremeWirelessScanSendAPAddedTrap is true." ::= { extremeAPTrapsPrefix 5 } extremeWirelessAPRemoved NOTIFICATION-TYPE OBJECTS { ifIndex, extremeWirelessScanResultsStationId } STATUS current DESCRIPTION "This is generated when an AP is removed from the scan results table. It will ony be generated if the value of extremeWirelessScanSendAPRemovedTrap is true." ::= { extremeAPTrapsPrefix 6 } extremeWirelessAPUpdated NOTIFICATION-TYPE OBJECTS { ifIndex, extremeWirelessScanResultsStationId, extremeWirelessScanResultsFirstSeen, extremeWirelessScanResultsLastChange, extremeWirelessScanResultsPacketRate, extremeWirelessScanResultsChannel, extremeWirelessScanResultsAvgRSS, extremeWirelessScanResultsSSID, extremeWirelessScanResultsRSNEnabled, extremeWirelessScanResultsPrivacy, extremeWirelessScanResultsNetworkType, extremeWirelessScanWPAIEMcastCipher, extremeWirelessScanWPAUcastCipherCount, extremeWirelessScanWPAUcastCipher, extremeWirelessScanWPAKeyMgmtCount, extremeWirelessScanWPAKeyMgmtSuite, extremeWirelessScanResultsRateSet, extremeWirelessScanResultsExtRateSet } STATUS current DESCRIPTION "This is generated when the IEs recorded for an AP in the scan results table change. It will only be generated if the value of SendAPUpdatedTrap is true." ::= { extremeAPTrapsPrefix 7 } extremeWirelessProbeInfoAdded NOTIFICATION-TYPE OBJECTS { ifIndex, extremeWirelessProbeInfoSource } STATUS current DESCRIPTION "This is generated when a new station is added to the probe info table. It will only be generated if the value of extremeWirelessProbeInfoSendAddedTrap is true." ::= { extremeAPTrapsPrefix 8 } extremeWirelessProbeInfoRemoved NOTIFICATION-TYPE OBJECTS { ifIndex, extremeWirelessProbeInfoSource } STATUS current DESCRIPTION "This is generated when a station is removed from the probe info table. It will only be generated if the value of extremeWirelessProbeInfoSendRemovedTrap is true." ::= { extremeAPTrapsPrefix 9 } extremeWirelessOffChannelScanStarted NOTIFICATION-TYPE OBJECTS { ifIndex, extremeWirelessOffChannelScanList } STATUS current DESCRIPTION "This is generated when an off-channel scan starts running." ::= { extremeAPTrapsPrefix 10 } extremeWirelessOffChannelScanFinished NOTIFICATION-TYPE OBJECTS { ifIndex, extremeWirelessOffChannelScanList } STATUS current DESCRIPTION "This is generated when an off-channel scan finishes running." ::= { extremeAPTrapsPrefix 11 } extremeWirelessCounterMeasureStarted NOTIFICATION-TYPE OBJECTS { ifIndex, extremeWirelessCounterMeasureSource } STATUS current DESCRIPTION "This trap is generated when counter measures are started on a wireless interface." ::= { extremeAPTrapsPrefix 12 } extremeWirelessCounterMeasureStopped NOTIFICATION-TYPE OBJECTS { ifIndex } STATUS current DESCRIPTION "This trap is generated when counter measures are stopped on a wireless interface." ::= { extremeAPTrapsPrefix 13 } --DFS related extremeWirelessInterfaceChannelRescan NOTIFICATION-TYPE OBJECTS { ifIndex, extremeWirelessPhysInterfacePHYChannel, extremeWirelessPhysInterfaceChannelAutoSelectStatus } STATUS current DESCRIPTION "This trap is generated when a wireless interface tries to autoselect a channel. It indicates whether a particular channel scan was successful, or if it failed then the reason for the failure." ::= { extremeAPTrapsPrefix 14 } -- -- TODO: Should we move this somewhere else? -- extremeWirelessCounterMeasureSource OBJECT-TYPE SYNTAX INTEGER { clientReport(1), micFailure(2) } MAX-ACCESS accessible-for-notify STATUS current DESCRIPTION "This value is used in the counter measure traps to indicate the reason that counter measures have been invoked." ::= { extremeAP 44 } extremeWirelessClientWPAStatsTable OBJECT-TYPE SYNTAX SEQUENCE OF ExtremeWirelessClientWPAStatsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains information of the WPA state transitions on a per-client basis. Rows are indexed first by virtual interface, then by client MAC." ::= { extremeAP 47 } extremeWirelessClientWPAStatsEntry OBJECT-TYPE SYNTAX ExtremeWirelessClientWPAStatsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Note that ifIndex here is virtual ifIndex (SSID)." INDEX { ifIndex, extremeWirelessClientDiagMac } ::= { extremeWirelessClientWPAStatsTable 1 } ExtremeWirelessClientWPAStatsEntry ::= SEQUENCE { extremeWirelessClientWPAStatsStarts Counter32, extremeWirelessClientWPAStatsPairwiseKeySuccesses Counter32, extremeWirelessClientWPAStatsPairwiseKeyFailures Counter32, extremeWirelessClientWPAStatsGroupKeySuccesses Counter32, extremeWirelessClientWPAStatsGroupKeyFailures Counter32, extremeWirelessClientWPAStatsPairwiseKey1Sends Counter32, extremeWirelessClientWPAStatsPairwiseKey3Sends Counter32, extremeWirelessClientWPAStatsGroupKeySends Counter32, extremeWirelessClientWPAStatsEAPOLKeyReceivedInPairwise1Key Counter32, extremeWirelessClientWPAStatsEAPOLKeyReceivedInPairwise3Key Counter32, extremeWirelessClientWPAStatsEAPOLKeyReceivedInGroupKey Counter32, extremeWirelessClientWPAStatsDoubleEAPOLKeyReceived Counter32, extremeWirelessClientWPAStatsEAPOLKeyIgnores Counter32, extremeWirelessClientWPAStatsEAPOLKeyErrors Counter32, extremeWirelessClientWPAStatsEAPOLKeyAborts Counter32, extremeWirelessClientWPAStatsEAPOLKeyVerificationSuccesses Counter32 } extremeWirelessClientWPAStatsStarts OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of starts of the WPA key exchange process" ::= { extremeWirelessClientWPAStatsEntry 1 } extremeWirelessClientWPAStatsPairwiseKeySuccesses OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of successes in the pairwise key handshake" ::= { extremeWirelessClientWPAStatsEntry 2 } extremeWirelessClientWPAStatsPairwiseKeyFailures OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of failures the pairwise key handshake" ::= { extremeWirelessClientWPAStatsEntry 3 } extremeWirelessClientWPAStatsGroupKeySuccesses OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of successes of the group key exchange" ::= { extremeWirelessClientWPAStatsEntry 4 } extremeWirelessClientWPAStatsGroupKeyFailures OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of failures of the group key handshake" ::= { extremeWirelessClientWPAStatsEntry 5 } extremeWirelessClientWPAStatsPairwiseKey1Sends OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of times the first packet of the pairwise key exchange was sent." ::= { extremeWirelessClientWPAStatsEntry 6 } extremeWirelessClientWPAStatsPairwiseKey3Sends OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of times the third packet of the pairwise key exchange was sent." ::= { extremeWirelessClientWPAStatsEntry 7 } extremeWirelessClientWPAStatsGroupKeySends OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of times the group key packet was sent." ::= { extremeWirelessClientWPAStatsEntry 8 } extremeWirelessClientWPAStatsEAPOLKeyReceivedInPairwise1Key OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of times an EAPOL Key packet was recieved after sending the 1st pairwise key exchange packet" ::= { extremeWirelessClientWPAStatsEntry 9 } extremeWirelessClientWPAStatsEAPOLKeyReceivedInPairwise3Key OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of times an EAPOL Key packet was recieved after sending the 3rd pairwise key exchange packet" ::= { extremeWirelessClientWPAStatsEntry 10 } extremeWirelessClientWPAStatsEAPOLKeyReceivedInGroupKey OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of times an EAPOL Key packet was recieved after sending the group key packet" ::= { extremeWirelessClientWPAStatsEntry 11 } extremeWirelessClientWPAStatsDoubleEAPOLKeyReceived OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of times an EAPOL Key packet was recieved when already processing a previous key packet." ::= { extremeWirelessClientWPAStatsEntry 12 } extremeWirelessClientWPAStatsEAPOLKeyIgnores OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of times an EAPOL Key packet was ignored." ::= { extremeWirelessClientWPAStatsEntry 13 } extremeWirelessClientWPAStatsEAPOLKeyErrors OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of times an EAPOL Key packet was errored." ::= { extremeWirelessClientWPAStatsEntry 14 } extremeWirelessClientWPAStatsEAPOLKeyAborts OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of times an EAPOL Key packet caused the WPA state machine to abort." ::= { extremeWirelessClientWPAStatsEntry 15 } extremeWirelessClientWPAStatsEAPOLKeyVerificationSuccesses OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of times an EAPOL Key packet was verified correctly." ::= { extremeWirelessClientWPAStatsEntry 16 } END -- ********************************************************************** -- * Extreme 802.11f MIB. Based on IEEE MIB with addition of ifIndex for -- * demux. -- **********************************************************************