WATCHGUARD-IPSEC-TUNNEL-MIB DEFINITIONS ::= BEGIN IMPORTS MODULE-IDENTITY, OBJECT-TYPE, Unsigned32, Counter64, OBJECT-IDENTITY, enterprises, Counter32, Integer32, IpAddress, TimeTicks FROM SNMPv2-SMI DateAndTime FROM SNMPv2-TC watchguard FROM WATCHGUARD-MIB; wgInfoModule MODULE-IDENTITY LAST-UPDATED "200701251200Z" ORGANIZATION "WatchGuard Technologies, Inc." CONTACT-INFO " Ella Yu WatchGuard Technologies, Inc. 1841 Zanker Road San Jose, CA 95112 USA 408-519-4888 ella.yu@watchguard.com " DESCRIPTION "The MIB module describes various tunnel objects of WatchGuard system." REVISION "200701251200Z" DESCRIPTION "Initial revision." ::= { watchguard 6 } wgIpsecTunnelMIB OBJECT-IDENTITY STATUS current DESCRIPTION "This is the base object identifier for all tunnel branches." ::= { wgInfoModule 5 } wgIpsecTunnel OBJECT-IDENTITY STATUS current DESCRIPTION "This is the base object identifier for all tunnel information." ::= { wgIpsecTunnelMIB 1 } wgIpsecTunnelNum OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of entries in the wgIpsecTunnelTable. " ::= { wgIpsecTunnel 1 } wgIpsecTunnelTable OBJECT-TYPE SYNTAX SEQUENCE OF WGIpsecTunnelEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This is the connection table describing all current tunnels exist on this entity." ::= { wgIpsecTunnel 2 } wgIpsecTunnelEntry OBJECT-TYPE SYNTAX WGIpsecTunnelEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry (conceptual row) containing the information on a tunnel between two security gateways." INDEX{ wgIpsecTunnelID } ::= { wgIpsecTunnelTable 1 } WGIpsecTunnelEntry ::= SEQUENCE { wgIpsecTunnelID Integer32, wgIpsecTunnelLocalAddr IpAddress, wgIpsecTunnelPeerAddr IpAddress, wgIpsecTunnelInSpi Integer32, wgIpsecTunnelOutSpi Integer32, wgIpsecTunnelCreateTime DateAndTime, wgIpsecTunnelDeviceID Unsigned32, wgIpsecTunnelEspEncryptAlg INTEGER, wgIpsecTunnelEspAuthAlg INTEGER, wgIpsecTunnelAhAuthAlg INTEGER, wgIpsecTunnelMode INTEGER, wgIpsecTunnelKeyMode INTEGER, wgIpsecTunnelLifeTime TimeTicks, wgIpsecTunnelLifeLength Counter32, wgIpsecTunnelInSaBytes Counter32, wgIpsecTunnelOutSaBytes Counter32, wgIpsecTunnelAccSecs Counter32, wgIpsecTunnelSelectorProtocol INTEGER, wgIpsecTunnelSelectorRemoteIPType INTEGER, wgIpsecTunnelSelectorRemoteIPOne IpAddress, wgIpsecTunnelSelectorRemoteIPTwo IpAddress, wgIpsecTunnelSelectorRemotePort INTEGER, wgIpsecTunnelSelectorLocalIPType INTEGER, wgIpsecTunnelSelectorLocalIPOne IpAddress, wgIpsecTunnelSelectorLocalIPTwo IpAddress, wgIpsecTunnelSelectorLocalPort INTEGER, wgIpsecTunnelNumRekey Counter32, wgIpsecTunnelInKbytes Counter32, wgIpsecTunnelOutKbytes Counter32, wgIpsecTunnelInPackets Counter32, wgIpsecTunnelOutPackets Counter32, wgIpsecTunnelInDecryptErrors Counter32, wgIpsecTunnelInAuthErrors Counter32, wgIpsecTunnelInReplayErrors Counter32, wgIpsecTunnelInOtherErrors Counter32, wgIpsecTunnelOutDecryptErrors Counter32, wgIpsecTunnelOutAuthErrors Counter32, wgIpsecTunnelOutReplayErrors Counter32, wgIpsecTunnelOutOtherErrors Counter32, wgIpsecTunnelUdpEncap INTEGER, wgIpsecTunnelPeerUdpPort INTEGER, wgIpsecTunnelOrigPeerAddr IpAddress } wgIpsecTunnelID OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The running index of this tunnel." ::= { wgIpsecTunnelEntry 1 } wgIpsecTunnelLocalAddr OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The local IP address of the current tunnel." ::= { wgIpsecTunnelEntry 2 } wgIpsecTunnelPeerAddr OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The remote IP address of the current tunnel." ::= { wgIpsecTunnelEntry 3 } wgIpsecTunnelInSpi OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The security parameters index of inbound SA's within this tunnel." ::= { wgIpsecTunnelEntry 4 } wgIpsecTunnelOutSpi OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The security parameters index of outbound SA's within this tunnel." ::= { wgIpsecTunnelEntry 5 } wgIpsecTunnelCreateTime OBJECT-TYPE SYNTAX DateAndTime MAX-ACCESS read-only STATUS current DESCRIPTION "The date and time when the tunnel is created." ::= { wgIpsecTunnelEntry 6 } wgIpsecTunnelDeviceID OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "The identifier of target device where the SA resides." ::= { wgIpsecTunnelEntry 7 } wgIpsecTunnelEspEncryptAlg OBJECT-TYPE SYNTAX INTEGER { unknown(0), des(2), three-des(3) } MAX-ACCESS read-only STATUS current DESCRIPTION "The encryption algorithm used in the tunnel. It's 0 if ESP is not used." ::= { wgIpsecTunnelEntry 8 } wgIpsecTunnelEspAuthAlg OBJECT-TYPE SYNTAX INTEGER { unknown(0), md5(2), sha(3) } MAX-ACCESS read-only STATUS current DESCRIPTION "The authentication algorithm used in the tunnel. It's 0 if ESP is not used." ::= { wgIpsecTunnelEntry 9 } wgIpsecTunnelAhAuthAlg OBJECT-TYPE SYNTAX INTEGER { unknown(0), md5(2), sha(3) } MAX-ACCESS read-only STATUS current DESCRIPTION "The AH authentication algorithm used in the tunnel. It's 0 if AH is not used." ::= { wgIpsecTunnelEntry 10 } wgIpsecTunnelMode OBJECT-TYPE SYNTAX INTEGER { unknown(0), tunnel(1), transport(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "The tunnel/transport mode of the tunnel." ::= { wgIpsecTunnelEntry 11 } wgIpsecTunnelKeyMode OBJECT-TYPE SYNTAX INTEGER { unknown(0), manual(1), auto-ike(2), other(3) } MAX-ACCESS read-only STATUS current DESCRIPTION "The key mode of the tunnel." ::= { wgIpsecTunnelEntry 12 } wgIpsecTunnelLifeTime OBJECT-TYPE SYNTAX TimeTicks MAX-ACCESS read-only STATUS current DESCRIPTION "The life time (in hundredths of a second) of the tunnel." ::= { wgIpsecTunnelEntry 13 } wgIpsecTunnelLifeLength OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The maximum traffic in bytes that the tunnel is allowed to support." ::= { wgIpsecTunnelEntry 14 } wgIpsecTunnelInSaBytes OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Current active inbound SA bytes of the tunnel." ::= { wgIpsecTunnelEntry 15 } wgIpsecTunnelOutSaBytes OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Current active outbound SA bytes of the tunnel." ::= { wgIpsecTunnelEntry 16 } wgIpsecTunnelAccSecs OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of seconds that the tunnel has existed." ::= { wgIpsecTunnelEntry 17 } wgIpsecTunnelSelectorProtocol OBJECT-TYPE SYNTAX INTEGER { any(0), icmp(1), igmp(2), ipip(4), tcp(6), egp(8), pup(12), udp(17), idp(22), tp(29), ipv6(41), ipv6-routing(43), ipv6-fragmentation(44), rsvp(46), gre(47), esp(50), ah(51), icmpv6(58), none(59), dstopts(60), mtp(92), encap(98), pim(103), raw(255) } MAX-ACCESS read-only STATUS current DESCRIPTION "The ip protocol number that this SA selector carries, or 0 if it carries any protocol." ::= { wgIpsecTunnelEntry 18 } wgIpsecTunnelSelectorRemoteIPType OBJECT-TYPE SYNTAX INTEGER { ip-addr-single(1), ip-addr-subnet(2), ip-addr-range(3) } MAX-ACCESS read-only STATUS current DESCRIPTION "The type of remote IP address of the SA selector in the entity." ::= { wgIpsecTunnelEntry 19 } wgIpsecTunnelSelectorRemoteIPOne OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The first remote IP address of the SA selector in the entity. It's IP address if remote IP of this selector only has one address. It's IP address of subnet if the remote IP of this selector is IP subnet. It's the start IP address if the remote IP of this selector has a range of addresses." ::= { wgIpsecTunnelEntry 20 } wgIpsecTunnelSelectorRemoteIPTwo OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The second remote IP address of the SA selector in the entity. It's 0 if remote IP of this selector only has one address. It's netmask of subnet if the remote IP of this selector is IP subnet. It's the end IP address if the remote IP of this selector has a range of addresses." ::= { wgIpsecTunnelEntry 21 } wgIpsecTunnelSelectorRemotePort OBJECT-TYPE SYNTAX INTEGER (0..65535) MAX-ACCESS read-only STATUS current DESCRIPTION "The remote port used by this selector in the entity." ::= { wgIpsecTunnelEntry 22 } wgIpsecTunnelSelectorLocalIPType OBJECT-TYPE SYNTAX INTEGER { ip-addr-single(1), ip-addr-subnet(2), ip-addr-range(3) } MAX-ACCESS read-only STATUS current DESCRIPTION "The type of local IP address of the SA selector in the entity." ::= { wgIpsecTunnelEntry 23 } wgIpsecTunnelSelectorLocalIPOne OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The first local IP address of the SA selector in the entity. It's IP address if local IP of this selector only has one address. It's IP address of subnet if the local IP of this selector is IP subnet. It's the start IP address if the local IP of this selector has a range of IP addresses." ::= { wgIpsecTunnelEntry 24 } wgIpsecTunnelSelectorLocalIPTwo OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The second local IP address of the SA selector in the entity. It's 0 if local IP of this selector only has one address. It's netmask of subnet if the local IP of this selector is IP subnet. It's the end IP address if the local IP of this selector has a range of IP addresses." ::= { wgIpsecTunnelEntry 25 } wgIpsecTunnelSelectorLocalPort OBJECT-TYPE SYNTAX INTEGER (0..65535) MAX-ACCESS read-only STATUS current DESCRIPTION "The local port used by this selector in the entity." ::= { wgIpsecTunnelEntry 26 } wgIpsecTunnelNumRekey OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of rekeys of the tunnel." ::= { wgIpsecTunnelEntry 27 } wgIpsecTunnelInKbytes OBJECT-TYPE SYNTAX Counter32 UNITS "Kbytes" MAX-ACCESS read-only STATUS current DESCRIPTION "Total inbound traffic in Kbytes since the establish of this tunnel." ::= { wgIpsecTunnelEntry 28 } wgIpsecTunnelOutKbytes OBJECT-TYPE SYNTAX Counter32 UNITS "Kbytes" MAX-ACCESS read-only STATUS current DESCRIPTION "Total outound traffic in Kbytes since the establish of this connection." ::= { wgIpsecTunnelEntry 29 } wgIpsecTunnelInPackets OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Total number of inbound packets since the establish of this connection." ::= { wgIpsecTunnelEntry 30 } wgIpsecTunnelOutPackets OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Total number of outound packets since the establish of this connection." ::= { wgIpsecTunnelEntry 31 } wgIpsecTunnelInDecryptErrors OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Total number of packets discarded due to decryption error since the establish of this connection." ::= { wgIpsecTunnelEntry 32 } wgIpsecTunnelInAuthErrors OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Total number of packets discarded due to authentication error since the establish of this connection." ::= { wgIpsecTunnelEntry 33 } wgIpsecTunnelInReplayErrors OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Total number of packets discarded due to replay error since the establish of this connection." ::= { wgIpsecTunnelEntry 34} wgIpsecTunnelInOtherErrors OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of packets discarded due to errors other than decryption, authentication or replay errors. This may include packets dropped due to a lack of receive buffers, and may include packets dropped due to congestion at the decryption element." ::= { wgIpsecTunnelEntry 35 } wgIpsecTunnelOutDecryptErrors OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Total number of packets discarded due to decryption error since the establish of this connection." ::= { wgIpsecTunnelEntry 36 } wgIpsecTunnelOutAuthErrors OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Total number of packets discarded due to authentication error since the establish of this connection." ::= { wgIpsecTunnelEntry 37 } wgIpsecTunnelOutReplayErrors OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Total number of packets discarded due to replay error since the establish of this connection." ::= { wgIpsecTunnelEntry 38 } wgIpsecTunnelOutOtherErrors OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of packets discarded due to errors other than decryption, authentication or replay errors. This may include packets dropped due to a lack of receive buffers, and may include packets dropped due to congestion at the decryption element." ::= { wgIpsecTunnelEntry 39 } wgIpsecTunnelUdpEncap OBJECT-TYPE SYNTAX INTEGER { disabled(0), enabled(1) } MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates whether if UDP encapsulated IPSec has been enabled." ::= { wgIpsecTunnelEntry 40 } wgIpsecTunnelPeerUdpPort OBJECT-TYPE SYNTAX INTEGER (0..65535) MAX-ACCESS read-only STATUS current DESCRIPTION "The peer's UDP port of current tunnel when UDP encapsulated IPSec is enabled." ::= { wgIpsecTunnelEntry 41 } wgIpsecTunnelOrigPeerAddr OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The original peer ip address of current tunnel when UDP encapsulated IPSec is enabled" ::= { wgIpsecTunnelEntry 42 } END