Wellfleet-DLS-MIB DEFINITIONS ::= BEGIN -- Created by mdl2asn version 3.1 -- Creation date: Wed Aug 30 16:39:40 EDT 1995 IMPORTS IpAddress, Counter, Gauge FROM RFC1155-SMI OBJECT-TYPE FROM RFC-1212 DisplayString FROM RFC1213-MIB wfDlsGroup FROM Wellfleet-COMMON-MIB; wfDls OBJECT IDENTIFIER ::= { wfDlsGroup 1 } wfDlsDelete OBJECT-TYPE SYNTAX INTEGER { created(1), deleted(2) } ACCESS read-write STATUS mandatory DESCRIPTION "Create/Delete parameter. Default is created. Users perform an SNMP SET operation on this object in order to create/delete DLSw" DEFVAL { created } ::= { wfDls 1 } wfDlsDisable OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } ACCESS read-write STATUS mandatory DESCRIPTION "Enable/Disable parameter. Default is enabled. Users perform an SNMP SET operation on this object in order to enable/disable DLSw" DEFVAL { enabled } ::= { wfDls 2 } wfDlsState OBJECT-TYPE SYNTAX INTEGER { up(1), down(2), init(3), notpresent(4) } ACCESS read-only STATUS mandatory DESCRIPTION "The current state of DLSw" DEFVAL { down } ::= { wfDls 3 } wfDlsTcpWindowSize OBJECT-TYPE SYNTAX INTEGER(5000..64000) ACCESS read-write STATUS mandatory DESCRIPTION "The size in bytes of the windows used for the DLSw TCP connections" DEFVAL { 8000 } ::= { wfDls 4 } wfDlsVirtualRing OBJECT-TYPE SYNTAX INTEGER ACCESS read-write STATUS mandatory DESCRIPTION "The virtual ring number for the TCP/IP cloud. Valid values (1-4095)" ::= { wfDls 5 } wfDlsInternalLanId OBJECT-TYPE SYNTAX INTEGER ACCESS read-write STATUS mandatory DESCRIPTION "The source routing internal lan id. Valid Values (1-4095)" ::= { wfDls 6 } wfDlsBridgeId OBJECT-TYPE SYNTAX INTEGER ACCESS read-write STATUS mandatory DESCRIPTION "The source routing base bridge number. Valid Values (1-15)" ::= { wfDls 7 } wfDlsMaxSlotSessions OBJECT-TYPE SYNTAX INTEGER(1..10000) ACCESS read-write STATUS mandatory DESCRIPTION "The maximum number of LLC2 sessions to support per slot" DEFVAL { 200 } ::= { wfDls 8 } wfDlsTotalCircuits OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "A current count of the total number of DLSw circuits established" ::= { wfDls 9 } wfDlsVirtualRingMtu OBJECT-TYPE SYNTAX INTEGER(1..16383) ACCESS read-write STATUS mandatory DESCRIPTION "The MTU to use in explorers generated by this DLSw. It should reflect the minimum MTU size of the entire network including the remote LANs. Valid values (> 0)" DEFVAL { 1500 } ::= { wfDls 10 } wfDlsMacAgeTime OBJECT-TYPE SYNTAX Gauge(0..4294967295) ACCESS read-write STATUS mandatory DESCRIPTION "The time in seconds before inactive MAC addresses will be aged out of the cache. Valid values (> 20)" DEFVAL { 300 } ::= { wfDls 11 } wfDlsNbAgeTime OBJECT-TYPE SYNTAX Gauge(21..4294967295) ACCESS read-write STATUS mandatory DESCRIPTION "The time in seconds before inactive NetBIOS names will be aged out of the cache. Valid values (> 20)" DEFVAL { 300 } ::= { wfDls 12 } wfDlsUnconfPeerReject OBJECT-TYPE SYNTAX INTEGER { accepted(1), rejected(2) } ACCESS read-write STATUS mandatory DESCRIPTION "Allow establishment of TCP connections from peers not in the Peer Table" DEFVAL { accepted } ::= { wfDls 13 } wfDlsDebugLevel1 OBJECT-TYPE SYNTAX Gauge ACCESS read-write STATUS mandatory DESCRIPTION "First Level debug flag. Cannot be configured with Site Manager. When this flag is set to Zero, no debug messages will be logged. Each bit of this flag represents certain functionality in DLSw. When this bit is set, all level2 elements that are part of this functionality that have their bits set will be allowed to log debug messages." DEFVAL { 4294967295 } ::= { wfDls 14 } wfDlsDebugLevel2 OBJECT-TYPE SYNTAX Gauge ACCESS read-write STATUS mandatory DESCRIPTION "Second Level debug flag. Cannot be configured with Site Manager. When this flag is set to Zero, no debug messages will be logged. Each bit of this flag represents a sub-functional element. When this bit is set, all debug messages in this element will be logged, as long as the related level1 functionality is set." DEFVAL { 0 } ::= { wfDls 15 } wfDlsWanKeepaliveTime OBJECT-TYPE SYNTAX INTEGER(0..2147483647) ACCESS read-write STATUS mandatory DESCRIPTION "Keepalive packets will be sent into inactive, established TCP connections after this time interval (in seconds). A time of zero disables this keepalive feature." DEFVAL { 60 } ::= { wfDls 16 } wfDlsPPriDisable OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } ACCESS read-write STATUS mandatory DESCRIPTION "Protocol Prioritization Enable/Disable parameter. Default is disabled. Users perform an SNMP SET operation to enable/disable this feature." DEFVAL { disabled } ::= { wfDls 17 } wfDlsPPriDefaultNumQueues OBJECT-TYPE SYNTAX INTEGER(1..10) ACCESS read-write STATUS mandatory DESCRIPTION "DLSw Prioritization Default number of Queues. The number of queues to be created when establishing a Peer connection if none have been previously defined. The default is two queues: queue number 0 and 1." DEFVAL { 2 } ::= { wfDls 18 } wfDlsPPriDefaultQBandwidth OBJECT-TYPE SYNTAX OCTET STRING ACCESS read-write STATUS mandatory DESCRIPTION "DLSw Prioritization Default Queues Bandwidth. The bandwidth for each default queue. Default of: 60% queue 0, 40% queue 1 via site manager." ::= { wfDls 19 } wfDlsPPriUnconfPeerDisable OBJECT-TYPE SYNTAX INTEGER { enable(1), disable(2) } ACCESS read-write STATUS mandatory DESCRIPTION "DLSw Prioritization enabled/disabled for peers not in Peer Table." DEFVAL { disable } ::= { wfDls 20 } wfDlsPPriUnconfPeerMaxQBuf OBJECT-TYPE SYNTAX INTEGER { default(50) } ACCESS read-write STATUS mandatory DESCRIPTION "DLSw Prioritization enabled/disabled for peers not in Peer Table." DEFVAL { default } ::= { wfDls 21 } wfDlsPPriUnconfPeerMaxQSize OBJECT-TYPE SYNTAX INTEGER { default(16000) } ACCESS read-write STATUS mandatory DESCRIPTION "DLSw Prioritization enabled/disabled for peers not in Peer Table." DEFVAL { default } ::= { wfDls 22 } wfDlsPkgMaxSize OBJECT-TYPE SYNTAX INTEGER(0..2147483647) ACCESS read-write STATUS mandatory DESCRIPTION "Maximum size of frame to sended over the WAN. Used when packaging multiple DLS frames into a single TCP frame. The value specified must be smaller than the wfDlsTcpWindowSize and should be no greater than the MTU for the WAN minus the size of the TCP/IP/MAC headers." DEFVAL { 1532 } ::= { wfDls 23 } wfDlsPkgTO OBJECT-TYPE SYNTAX INTEGER(0..2147483647) ACCESS read-write STATUS mandatory DESCRIPTION "DLSw packaging Time-out. Number of msec to delay a package before sending to TCP. This value should be based on the WAN speed wfDlsPkgWinPercent (defined below). This value should be no greater than the amount of time it takes to send the number of outstanding bytes before packaging begins: number bytes / (number bytes per msec) Default of 10 msec. " DEFVAL { 10 } ::= { wfDls 24 } wfDlsPkgWinPercent OBJECT-TYPE SYNTAX INTEGER(0..100) ACCESS read-write STATUS mandatory DESCRIPTION "DLSw Packaging threshold. What percent of the DLS TCP window must be outstanding inorder to delay the sending of a package being built. Default: 20% of TCP window. Range: 0 - 100, with 0 meaning no delay." DEFVAL { 20 } ::= { wfDls 25 } wfDlsMultislotBcasts OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } ACCESS read-write STATUS mandatory DESCRIPTION "Allow broadcasts inbound from the WAN to be broadcast to all active DLSw slots." DEFVAL { enabled } ::= { wfDls 26 } wfDlsInitialPacingWindow OBJECT-TYPE SYNTAX INTEGER(5..100) ACCESS read-write STATUS mandatory DESCRIPTION "Initial pacing window to be advertised in Capabilities Exchange messages. Adaptive pacing will begin with this value and use the state of the network to find the proper pacing window size." DEFVAL { 5 } ::= { wfDls 27 } wfDlsRfc OBJECT-TYPE SYNTAX INTEGER { rfc1434(1), rfc1795(2), v20unicast(3), rfc2166(4) } ACCESS read-write STATUS mandatory DESCRIPTION "DLSw RFC mode selection. - RFC1434 is the original implementation - RFC1795 provides improved interoperability and flow control - v20_unicast supports Canureach Exploring via unicast UDP frames and provides single TCP connections - RFC2166 additionally supports Multicast Canureach Exploring" DEFVAL { rfc1434 } ::= { wfDls 28 } wfDlsNetbiosSessionAliveFilter OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } ACCESS read-write STATUS mandatory DESCRIPTION "Netbios session alive filter." DEFVAL { disabled } ::= { wfDls 29 } wfDlsWanKeepaliveRetryTimer OBJECT-TYPE SYNTAX INTEGER(0..600) ACCESS read-write STATUS mandatory DESCRIPTION "KEEPALIVE retransmit timeout period, in seconds. This is the interval at which unacknowledged KEEPALIVE messages will be retransmitted. If the Idle Timer is set to zero, this timer ignored. If the Idle Timer is non-zero and this timer IS zero, no KEEPALIVEs are sent and the session is terminated upon expiration of the Idle Timer." DEFVAL { 60 } ::= { wfDls 30 } wfDlsWanKeepaliveRetries OBJECT-TYPE SYNTAX INTEGER(0..99) ACCESS read-write STATUS mandatory DESCRIPTION "Number of unacknowledged KEEPALIVE messages retransmitted before the TCP session is terminated. If this count is set to zero, only one KEEPALIVE message will be sent." DEFVAL { 4 } ::= { wfDls 31 } wfDlsSnaFallbackAttempts OBJECT-TYPE SYNTAX INTEGER(0..2147483647) ACCESS read-write STATUS mandatory DESCRIPTION "Number of times CANUREACH_ex will be sent (for SNA based connections) before attempting to fall back. Used for peers configured as wfDlsPeerTransportType = unknown to attempt connecting via RFC 1795." DEFVAL { 5 } ::= { wfDls 32 } wfDlsNetbiosFallbackTime OBJECT-TYPE SYNTAX INTEGER(0..2147483647) ACCESS read-write STATUS mandatory DESCRIPTION "Amount of time in sec before falling back to RFC 1795 for the peers configured with wfDlsPeerTransportType = unknown, if NETBIOS_NQ does not get answered." DEFVAL { 180 } ::= { wfDls 33 } wfDlsTcpInactTime OBJECT-TYPE SYNTAX INTEGER(0..2147483647) ACCESS read-write STATUS mandatory DESCRIPTION "Amount of time in sec after the last active DLSw circuit has terminated or there was no data transfered over TCP pipe, before bringing down TCP connection. Used in conjunction with wfDlsTcpInactMethod." DEFVAL { 300 } ::= { wfDls 34 } wfDlsTcpInactMethod OBJECT-TYPE SYNTAX INTEGER { never (1), circuits(2), data(3) } ACCESS read-write STATUS mandatory DESCRIPTION "Determines when tcp connections may be brought down. Could be due to no DLS circuits on a peer, no data passing over the TCP link, or leave the TCP connection up. Used in conjunction with wfDlsTcpInactTime." DEFVAL { circuits } ::= { wfDls 35 } wfDlsMslotDLCBcasts OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } ACCESS read-write STATUS mandatory DESCRIPTION "Allow broadcast messages inbound from the DLC to be sent to all active DLSw slots." DEFVAL { enabled } ::= { wfDls 36 } wfDlsRsvpSupport OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } ACCESS read-write STATUS mandatory DESCRIPTION "Enables/Disables use of RSVP by DLSw" DEFVAL { disabled } ::= { wfDls 37 } wfDlsOutBandwidth OBJECT-TYPE SYNTAX INTEGER(0..2147483647) ACCESS read-write STATUS mandatory DESCRIPTION "Bandwidth amount for the outgoing DLSw traffic, to use in RSVP reservations for unconfigured peers" DEFVAL { 0 } ::= { wfDls 38 } wfDlsOutBurstSize OBJECT-TYPE SYNTAX INTEGER(0..2147483647) ACCESS read-write STATUS mandatory DESCRIPTION "Burst Size amount for the outgoing DLSw traffic, to use in RSVP reservations for unconfigured peers" DEFVAL { 0 } ::= { wfDls 39 } wfDlsInBandwidth OBJECT-TYPE SYNTAX INTEGER(0..2147483647) ACCESS read-write STATUS mandatory DESCRIPTION "Bandwidth amount for the incoming DLSw traffic, to use in RSVP reservations for unconfigured peers" DEFVAL { 0 } ::= { wfDls 40 } wfDlsInBurstSize OBJECT-TYPE SYNTAX INTEGER(0..2147483647) ACCESS read-write STATUS mandatory DESCRIPTION "Burst Size amount for the incoming DLSw traffic, to use in RSVP reservations for unconfigured peers" DEFVAL { 0 } ::= { wfDls 41 } wfDlsNonPeakOutBandwidth OBJECT-TYPE SYNTAX INTEGER(0..2147483647) ACCESS read-write STATUS mandatory DESCRIPTION "Bandwidth amount for the outgoing DLSw traffic, to use in RSVP reservations for unconfigured peers during non-peak hours" DEFVAL { 0 } ::= { wfDls 42 } wfDlsNonPeakOutBurstSize OBJECT-TYPE SYNTAX INTEGER(0..2147483647) ACCESS read-write STATUS mandatory DESCRIPTION "Burst Size amount for the outgoing DLSw traffic, to use in RSVP reservations for unconfigured peers during non-peak hours" DEFVAL { 0 } ::= { wfDls 43 } wfDlsNonPeakInBandwidth OBJECT-TYPE SYNTAX INTEGER(0..2147483647) ACCESS read-write STATUS mandatory DESCRIPTION "Bandwidth amount for the incoming DLSw traffic, to use in RSVP reservations for unconfigured peers during non-peak hours" DEFVAL { 0 } ::= { wfDls 44 } wfDlsNonPeakInBurstSize OBJECT-TYPE SYNTAX INTEGER(0..2147483647) ACCESS read-write STATUS mandatory DESCRIPTION "Burst Size amount for the incoming DLSw traffic, to use in RSVP reservations for unconfigured peers during non-peak hours" DEFVAL { 0 } ::= { wfDls 45 } wfDlsNonPeakStartTime OBJECT-TYPE SYNTAX INTEGER(0..2400) ACCESS read-write STATUS mandatory DESCRIPTION "Start time of the non-peak hours in hhmm format and 24 hour clock. If start time is greater in value than end time, non-peak hours ends the next day." DEFVAL { 0 } ::= { wfDls 46 } wfDlsNonPeakEndTime OBJECT-TYPE SYNTAX INTEGER(0..2400) ACCESS read-write STATUS mandatory DESCRIPTION "End time of the non-peak hours in hhmm 24 hour clock format" DEFVAL { 0 } ::= { wfDls 47 } wfDlsNonPeakStartDays OBJECT-TYPE SYNTAX Counter ACCESS read-write STATUS mandatory DESCRIPTION "Bitmap of the starting days of the week for a non-peak reservations. The MSBit represents Sunday, the next most significant bit represents Monday, and so on... Default is 0 - non-peak parameters are not used." ::= { wfDls 48 } wfDlsMultislotCacheUpdate OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } ACCESS read-write STATUS mandatory DESCRIPTION "Allow learned MAC-IP cache resolutions to be promulgated to all other DLSw slots." DEFVAL { enabled } ::= { wfDls 49 } wfDlsMacAddrTranslation OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } ACCESS read-write STATUS mandatory DESCRIPTION "Enables/Disables use of Mac Address Translation by DLSw" DEFVAL { disabled } ::= { wfDls 50 } wfDlsBan2Support OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } ACCESS read-write STATUS mandatory DESCRIPTION "Enables/Disables BAN-2 local termination between SRB interfaces in single DLS switch configs" DEFVAL { disabled } ::= { wfDls 51 } wfDlsVirtualRingBridgeCheck OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } ACCESS read-write STATUS mandatory DESCRIPTION " DLSw Virtual Ring ID and SRB Bridge ID will be checked." DEFVAL { disabled } ::= { wfDls 52 } wfDlsAcceptBadVendorSpecificCapex OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } ACCESS read-write STATUS mandatory DESCRIPTION "Accept a capex request containing a Vendor Specific Control Vector but no Vendor Context. The Control Vector will be ignored" DEFVAL { disabled } ::= { wfDls 53 } wfDlsDiagSwitch OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } ACCESS read-write STATUS mandatory DESCRIPTION "Available MIB for diagnostic workspaces. Allows optional conditional debugging" DEFVAL { disabled } ::= { wfDls 54 } wfDlsAllowSpecAddrNbDatagram OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } ACCESS read-write STATUS mandatory DESCRIPTION "Allows acceptance of NETBIOS Datagrams sent to other than the NETBIOS Group address as the destination MAC address. This is an override MIB. When enabled, DLS will bypass its check for that group address and allow the packet." DEFVAL { disabled } ::= { wfDls 55 } wfDlsInterfaceTable OBJECT-TYPE SYNTAX SEQUENCE OF WfDlsInterfaceEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "A table that contains information about every interface that is associated with DLSw inst_id[1] = wfDlsInterfaceCircuit" ::= { wfDlsGroup 2 } wfDlsInterfaceEntry OBJECT-TYPE SYNTAX WfDlsInterfaceEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "An entry in wfDlsInterface" INDEX { wfDlsInterfaceCircuit } ::= { wfDlsInterfaceTable 1 } WfDlsInterfaceEntry ::= SEQUENCE { wfDlsInterfaceDelete INTEGER, wfDlsInterfaceDisable INTEGER, wfDlsInterfaceState INTEGER, wfDlsInterfaceCircuit INTEGER, wfDlsInterfaceBridgeId INTEGER, wfDlsInterfaceLanId INTEGER, wfDlsInterfaceDlcType INTEGER, wfDlsInterfaceSdlcMode INTEGER, wfDlsInterfaceNbBcastDgramReduce INTEGER, wfDlsInterfaceExplorerType INTEGER, wfDlsInterfaceNbBcastDgramCache INTEGER, wfDlsInterfaceClrCallEnable INTEGER } wfDlsInterfaceDelete OBJECT-TYPE SYNTAX INTEGER { created(1), deleted(2) } ACCESS read-write STATUS mandatory DESCRIPTION "Create/Delete parameter. Default is created. Users perform an SNMP SET operation on this object in order to create/delete an interface" DEFVAL { created } ::= { wfDlsInterfaceEntry 1 } wfDlsInterfaceDisable OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } ACCESS read-write STATUS mandatory DESCRIPTION "Enable/Disable parameter. Default is enabled. Users perform an SNMP SET operation on this object in order to enable/disable an interface" DEFVAL { enabled } ::= { wfDlsInterfaceEntry 2 } wfDlsInterfaceState OBJECT-TYPE SYNTAX INTEGER { up(1), down(2), init(3), notpresent(4) } ACCESS read-only STATUS mandatory DESCRIPTION "The current state of the interface" DEFVAL { down } ::= { wfDlsInterfaceEntry 3 } wfDlsInterfaceCircuit OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The circuit that this interface runs over" ::= { wfDlsInterfaceEntry 4 } wfDlsInterfaceBridgeId OBJECT-TYPE SYNTAX INTEGER(1..15) ACCESS read-write STATUS mandatory DESCRIPTION "The Bridge Id of the 'bridge' from the internal Lan to the TCP/IP ring. This must be a non-Wellfleet bridge number. Valid Values (1-15)" ::= { wfDlsInterfaceEntry 5 } wfDlsInterfaceLanId OBJECT-TYPE SYNTAX INTEGER(1..4095) ACCESS read-write STATUS mandatory DESCRIPTION "The Lan Id of the interface. Valid Values (1-4095)" ::= { wfDlsInterfaceEntry 6 } wfDlsInterfaceDlcType OBJECT-TYPE SYNTAX INTEGER { sync(1), srb(2), tb(3), encaps(4), fr(5), token(6) } ACCESS read-write STATUS mandatory DESCRIPTION "The Data Link Control Type on this interface." DEFVAL { srb } ::= { wfDlsInterfaceEntry 7 } wfDlsInterfaceSdlcMode OBJECT-TYPE SYNTAX INTEGER { primary(1), pp(2), mp(3), negot(4) } ACCESS read-write STATUS mandatory DESCRIPTION "The SDLC Mode on this interface." DEFVAL { primary } ::= { wfDlsInterfaceEntry 8 } wfDlsInterfaceNbBcastDgramReduce OBJECT-TYPE SYNTAX INTEGER { on(1), off(2) } ACCESS read-write STATUS mandatory DESCRIPTION "This allows the NetBios Broadcast dgram reduction code built into dls to be turned off." DEFVAL { on } ::= { wfDlsInterfaceEntry 9 } wfDlsInterfaceExplorerType OBJECT-TYPE SYNTAX INTEGER { ste(1), are(2) } ACCESS read-write STATUS mandatory DESCRIPTION "This allows CANUREACH test frames to be sent as single-route or all-routes explorer frames." DEFVAL { ste } ::= { wfDlsInterfaceEntry 10 } wfDlsInterfaceNbBcastDgramCache OBJECT-TYPE SYNTAX INTEGER { off(1), forward(2), drop(3) } ACCESS read-write STATUS mandatory DESCRIPTION "This allows Netbios Broadcast datagram frames to be cached along with allowing these same frames to utilize the netbios caching mechanism. Value 1 means feature not on. Value 2 means if frame is not in cache then forward it. Value 3 means if frame is not in cache then drop it." DEFVAL { off } ::= { wfDlsInterfaceEntry 11 } wfDlsInterfaceClrCallEnable OBJECT-TYPE SYNTAX INTEGER { on(1), off(2) } ACCESS read-write STATUS mandatory DESCRIPTION "This allows a generic (e.g. QLLC/X25) call to be cleared when the DLS connection enters a DISCONNECTED state." DEFVAL { off } ::= { wfDlsInterfaceEntry 12 } wfDlsSlotTable OBJECT-TYPE SYNTAX SEQUENCE OF WfDlsSlotEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "A table that contains the IP interfaces each slot must use for the TCP connections to non-Wellfleet switches. The IP interface may exist anywhere on the box. inst_id[1] = wfDlsSlotNumber" ::= { wfDlsGroup 3 } wfDlsSlotEntry OBJECT-TYPE SYNTAX WfDlsSlotEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "An entry in wfDlsSlot" INDEX { wfDlsSlotNumber } ::= { wfDlsSlotTable 1 } WfDlsSlotEntry ::= SEQUENCE { wfDlsSlotDelete INTEGER, wfDlsSlotNumber INTEGER, wfDlsSlotIpAddr IpAddress, wfDlsCurrentMemory INTEGER, wfDlsMaxAllowedMemory Gauge, wfDlsHiWaterMark INTEGER, wfDlsSlotGenDestination INTEGER, wfDlsSlotGenSessions INTEGER, wfDlsSlotGenUpperMAC INTEGER, wfDlsSlotCurrentSessions INTEGER, wfDlsSlotHiWaterSessions INTEGER, wfDlsSlotHiWaterReset INTEGER } wfDlsSlotDelete OBJECT-TYPE SYNTAX INTEGER { created(1), deleted(2) } ACCESS read-write STATUS mandatory DESCRIPTION "Create/Delete parameter. Default is created. Users perform an SNMP SET operation on this object in order to create/delete a DLSw slot IP record" DEFVAL { created } ::= { wfDlsSlotEntry 1 } wfDlsSlotNumber OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The slot that uses this IP interface" ::= { wfDlsSlotEntry 2 } wfDlsSlotIpAddr OBJECT-TYPE SYNTAX IpAddress ACCESS read-write STATUS mandatory DESCRIPTION "The IP interface to use for TCP connections based on this slot" ::= { wfDlsSlotEntry 3 } wfDlsCurrentMemory OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Memory currently available on this slot" ::= { wfDlsSlotEntry 4 } wfDlsMaxAllowedMemory OBJECT-TYPE SYNTAX Gauge ACCESS read-write STATUS mandatory DESCRIPTION "Maximum amount of memory allowed to be allocated for DLS on this slot. 4294967295 = 0xFFFFFFFF stands for infinite. (i.e. all available memory)" DEFVAL { 4294967295 } ::= { wfDlsSlotEntry 5 } wfDlsHiWaterMark OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "This is the maximum amount of memory ever allocated by DLS on this slot since the last boot" ::= { wfDlsSlotEntry 6 } wfDlsSlotGenDestination OBJECT-TYPE SYNTAX INTEGER(0..14) ACCESS read-write STATUS mandatory DESCRIPTION "This is a destination slot of the GEN tool if the value is 0. For any non-zero number, the slot is a GEN source and the value of wfDlsSlotGenDestination is its destination slot." DEFVAL { 0 } ::= { wfDlsSlotEntry 7 } wfDlsSlotGenSessions OBJECT-TYPE SYNTAX INTEGER(0..10000) ACCESS read-write STATUS mandatory DESCRIPTION "The maximum number of Generator sessions to support per slot" DEFVAL { 0 } ::= { wfDlsSlotEntry 8 } wfDlsSlotGenUpperMAC OBJECT-TYPE SYNTAX INTEGER(0..2147418112) ACCESS read-write STATUS mandatory DESCRIPTION "The upper MAC address for this slot." DEFVAL { 0 } ::= { wfDlsSlotEntry 9 } wfDlsSlotCurrentSessions OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The number of sessions connected on this slot." DEFVAL { 0 } ::= { wfDlsSlotEntry 10} wfDlsSlotHiWaterSessions OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The highest number of sessions connected at one time on this slot." DEFVAL { 0 } ::= { wfDlsSlotEntry 11 } wfDlsSlotHiWaterReset OBJECT-TYPE SYNTAX INTEGER { normal(1), reset(2) } ACCESS read-write STATUS mandatory DESCRIPTION "Setting to 2 (reset) sets HiWaterSessions to CurrentSessions." DEFVAL { normal } ::= { wfDlsSlotEntry 12} wfDlsSapTable OBJECT-TYPE SYNTAX SEQUENCE OF WfDlsSapEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "A table that contains the SAPS to be terminated by DLSw. inst_id[1] = wfDlsSapAddr" ::= { wfDlsGroup 4 } wfDlsSapEntry OBJECT-TYPE SYNTAX WfDlsSapEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "An entry in wfDlsSap" INDEX { wfDlsSapAddr } ::= { wfDlsSapTable 1 } WfDlsSapEntry ::= SEQUENCE { wfDlsSapDelete INTEGER, wfDlsSapAddr INTEGER, wfDlsSapCredit INTEGER } wfDlsSapDelete OBJECT-TYPE SYNTAX INTEGER { created(1), deleted(2) } ACCESS read-write STATUS mandatory DESCRIPTION "Create/Delete parameter. Default is created. Users perform an SNMP SET operation on this object in order to create/delete a DLSw SAP record" DEFVAL { created } ::= { wfDlsSapEntry 1 } wfDlsSapAddr OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The SAP to be terminated by DLSw" ::= { wfDlsSapEntry 2 } wfDlsSapCredit OBJECT-TYPE SYNTAX INTEGER(6..200) ACCESS read-write STATUS mandatory DESCRIPTION "The LLC2 flow control credit size for this SAP. Flow control procedures will be invoked based on this parameter" DEFVAL { 10 } ::= { wfDlsSapEntry 3 } wfDlsPeerTable OBJECT-TYPE SYNTAX SEQUENCE OF WfDlsPeerEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "A table that contains the IP addresses of the DLSw peers with which we will establish TCP connections. inst_id[4] = wfDlsPeerAddr" ::= { wfDlsGroup 5 } wfDlsPeerEntry OBJECT-TYPE SYNTAX WfDlsPeerEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "An entry in wfDlsPeer" INDEX { wfDlsPeerIpAddr } ::= { wfDlsPeerTable 1 } WfDlsPeerEntry ::= SEQUENCE { wfDlsPeerDelete INTEGER, wfDlsPeerState INTEGER, wfDlsPeerIpAddr IpAddress, wfDlsPeerDefinedBy INTEGER, wfDlsPeerPPriDisable INTEGER, wfDlsPeerPPriMaxQBuf INTEGER, wfDlsPeerPPriMaxQSize INTEGER, wfDlsPeerPPriClearStats INTEGER, wfDlsPeerType INTEGER, wfDlsPeerTransportType INTEGER, wfDlsPeerBackupConfig INTEGER, wfDlsPeerBackupIpAddr IpAddress, wfDlsPeerBackupMaxUpTime INTEGER, wfDlsPeerBackupHoldDownTime INTEGER, wfDlsPeerBackupStartTime INTEGER, wfDlsPeerBackupEndTime INTEGER, wfDlsPeerInteroperability INTEGER, wfDlsPeerBackupType INTEGER, wfDlsPeerRsvpMode INTEGER, wfDlsPeerRsvpSlots Counter, wfDlsPeerOutBandwidth INTEGER, wfDlsPeerOutBurstSize INTEGER, wfDlsPeerInBandwidth INTEGER, wfDlsPeerInBurstSize INTEGER, wfDlsPeerNonPeakOutBandwidth INTEGER, wfDlsPeerNonPeakOutBurstSize INTEGER, wfDlsPeerNonPeakInBandwidth INTEGER, wfDlsPeerNonPeakInBurstSize INTEGER, wfDlsPeerNonPeakStartTime INTEGER, wfDlsPeerNonPeakEndTime INTEGER, wfDlsPeerNonPeakStartDays Counter, wfDlsPeerBackupOutBandwidth INTEGER, wfDlsPeerBackupOutBurstSize INTEGER, wfDlsPeerBackupInBandwidth INTEGER, wfDlsPeerBackupInBurstSize INTEGER } wfDlsPeerDelete OBJECT-TYPE SYNTAX INTEGER { created(1), deleted(2) } ACCESS read-write STATUS mandatory DESCRIPTION "Create/Delete parameter. Default is created. Users perform an SNMP SET operation on this object in order to create/delete a DLSw peer record" DEFVAL { created } ::= { wfDlsPeerEntry 1 } wfDlsPeerState OBJECT-TYPE SYNTAX INTEGER { connect(1), backup(2), notconn(3), invalid(4) } ACCESS read-only STATUS mandatory DESCRIPTION "The current state of the TCP connection with this DLSw peer" DEFVAL { notconn } ::= { wfDlsPeerEntry 2 } wfDlsPeerIpAddr OBJECT-TYPE SYNTAX IpAddress ACCESS read-only STATUS mandatory DESCRIPTION "The IP address of the DLSw peer" ::= { wfDlsPeerEntry 3 } wfDlsPeerDefinedBy OBJECT-TYPE SYNTAX INTEGER { configured(1), learned(2) } ACCESS read-only STATUS mandatory DESCRIPTION "The method by which this peer was defined" DEFVAL { configured } ::= { wfDlsPeerEntry 4 } wfDlsPeerPPriDisable OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } ACCESS read-write STATUS mandatory DESCRIPTION "DLSw Protocol Priority enabled/disabled for this Peer. The default is to use the value specified in the DLS Base record (wfDlsPPriDisable). Site Manager handles the setting of the default." DEFVAL { disabled } ::= { wfDlsPeerEntry 5 } wfDlsPeerPPriMaxQBuf OBJECT-TYPE SYNTAX INTEGER { default(50) } ACCESS read-write STATUS mandatory DESCRIPTION "Protocol Priority Queue Maximum number of allocated buffers queued." DEFVAL { default } ::= { wfDlsPeerEntry 6 } wfDlsPeerPPriMaxQSize OBJECT-TYPE SYNTAX INTEGER { default(16000) } ACCESS read-write STATUS mandatory DESCRIPTION "Protocol Priority Queue Maximum number of octets queued." DEFVAL { default } ::= { wfDlsPeerEntry 7 } wfDlsPeerPPriClearStats OBJECT-TYPE SYNTAX INTEGER ACCESS read-write STATUS mandatory DESCRIPTION "Clear Protocol Priority Statistics. If prioritization is enabled for this Peer, then modifying this attribute will cause all Statistics kept (Queue's, CC, etc) to be cleared." ::= { wfDlsPeerEntry 8 } wfDlsPeerType OBJECT-TYPE SYNTAX INTEGER { rfc1795(1), rfc1434(2), local(3), v20unicast(4), rfc2166(5), unknown(6) } ACCESS read-only STATUS mandatory DESCRIPTION "The protocol type of this DLSw peer" DEFVAL { unknown } ::= { wfDlsPeerEntry 9 } wfDlsPeerTransportType OBJECT-TYPE SYNTAX INTEGER { tcp(1), udp(2), unknown(3) } ACCESS read-write STATUS mandatory DESCRIPTION "The transport type of this DLSw peer" DEFVAL { unknown } ::= { wfDlsPeerEntry 10 } wfDlsPeerBackupConfig OBJECT-TYPE SYNTAX INTEGER { yes(1), no(2) } ACCESS read-write STATUS mandatory DESCRIPTION "The indication of whether or not a backup peer is to be configured for the primary peer. The default is no which means that there is no backup peer configured by default. A backup peer can only be configured for a RFC1434 or RFC1795 peer." DEFVAL { no } ::= { wfDlsPeerEntry 11 } wfDlsPeerBackupIpAddr OBJECT-TYPE SYNTAX IpAddress ACCESS read-write STATUS mandatory DESCRIPTION "The IP Address of the backup DLSw peer." ::= { wfDlsPeerEntry 12 } wfDlsPeerBackupMaxUpTime OBJECT-TYPE SYNTAX INTEGER(0..999999) ACCESS read-write STATUS mandatory DESCRIPTION "The maximum amount of time (in seconds) allowed for a TCP connection to stay established to the backup DLSw peer. If set to zero, this feature is disabled. Set to anything greater than zero to enable the feature." DEFVAL { 0 } ::= { wfDlsPeerEntry 13 } wfDlsPeerBackupHoldDownTime OBJECT-TYPE SYNTAX INTEGER(0..2147483647) ACCESS read-write STATUS mandatory DESCRIPTION "The amount of time (in seconds) to wait before starting a new TCP connection to the backup DLSw peer." DEFVAL { 120 } ::= { wfDlsPeerEntry 14 } wfDlsPeerBackupStartTime OBJECT-TYPE SYNTAX INTEGER(0..2400) ACCESS read-write STATUS mandatory DESCRIPTION "Used in conjunction with the EndTime attribute. Together these define a time interval for when a backup peer can be active. The start time is the beginning time of day that a backup peer can be established. (HHMM format)" DEFVAL { 0001 } ::= { wfDlsPeerEntry 15 } wfDlsPeerBackupEndTime OBJECT-TYPE SYNTAX INTEGER(1..2400) ACCESS read-write STATUS mandatory DESCRIPTION "Used in conjunction with the StartTime attribute. Together these define a time interval for when a backup peer can be active. The end time is the end time of day that a backup peer can be established. If a backup peer is active and the current time is after this end time, the backup peer will be brought down. (HHMM format)" DEFVAL { 2400 } ::= { wfDlsPeerEntry 16 } wfDlsPeerInteroperability OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } ACCESS read-write STATUS mandatory DESCRIPTION "If enabled, open write to read tcp connection for 1434 and 1795 type of peers. Let the other side to open the other connection." DEFVAL { enabled } ::= { wfDlsPeerEntry 17 } wfDlsPeerBackupType OBJECT-TYPE SYNTAX INTEGER { multicast(1), v20udp(2), v20unknown(3), v20tcp(4), tcp1795(5) } ACCESS read-write STATUS mandatory DESCRIPTION "The type of this DLSw backup peer" DEFVAL { v20unknown } ::= { wfDlsPeerEntry 18 } wfDlsPeerRsvpMode OBJECT-TYPE SYNTAX INTEGER { usePeerCfgParams(1), noRsvpForPeer(2), useGlobalCfgParams(3) } ACCESS read-write STATUS mandatory DESCRIPTION "Defines rsvp mode of operation for the peer: - 1 use rsvp parameters configured in the peer; - 2 do NOT use rsvp for this peer; - 3 use rsvp parameters configures in wfDls object." DEFVAL { useGlobalCfgParams } ::= { wfDlsPeerEntry 19 } wfDlsPeerRsvpSlots OBJECT-TYPE SYNTAX Counter ACCESS read-write STATUS mandatory DESCRIPTION "Bit mask field representing the slots, that may make RSVP resevations for this peer. The MSBit represents slot 1, the next most significant bit represents slot 2, and so on... Slots can be 1-14. Default is all slots on a BCN." ::= { wfDlsPeerEntry 20 } wfDlsPeerOutBandwidth OBJECT-TYPE SYNTAX INTEGER ACCESS read-write STATUS mandatory DESCRIPTION "Bandwidth amount for the outgoing DLSw traffic, to use in RSVP reservations for this peer" DEFVAL { 0 } ::= { wfDlsPeerEntry 21 } wfDlsPeerOutBurstSize OBJECT-TYPE SYNTAX INTEGER ACCESS read-write STATUS mandatory DESCRIPTION "Burst Size amount for the outgoing DLSw traffic, to use in RSVP reservations for this peer" DEFVAL { 0 } ::= { wfDlsPeerEntry 22 } wfDlsPeerInBandwidth OBJECT-TYPE SYNTAX INTEGER ACCESS read-write STATUS mandatory DESCRIPTION "Bandwidth amount for the incoming DLSw traffic, to use in RSVP reservations for this peer" DEFVAL { 0 } ::= { wfDlsPeerEntry 23 } wfDlsPeerInBurstSize OBJECT-TYPE SYNTAX INTEGER ACCESS read-write STATUS mandatory DESCRIPTION "Burst Size amount for the incoming DLSw traffic, to use in RSVP reservations for this peer" DEFVAL { 0 } ::= { wfDlsPeerEntry 24 } wfDlsPeerNonPeakOutBandwidth OBJECT-TYPE SYNTAX INTEGER ACCESS read-write STATUS mandatory DESCRIPTION "Bandwidth amount for the outgoing DLSw traffic, to use in RSVP reservations for this peer during non-peak hours" DEFVAL { 0 } ::= { wfDlsPeerEntry 25 } wfDlsPeerNonPeakOutBurstSize OBJECT-TYPE SYNTAX INTEGER ACCESS read-write STATUS mandatory DESCRIPTION "Burst Size amount for the outgoing DLSw traffic, to use in RSVP reservations for this peer during non-peak hours" DEFVAL { 0 } ::= { wfDlsPeerEntry 26 } wfDlsPeerNonPeakInBandwidth OBJECT-TYPE SYNTAX INTEGER ACCESS read-write STATUS mandatory DESCRIPTION "Bandwidth amount for the incoming DLSw traffic, to use in RSVP reservations for this peer during non-peak hours" DEFVAL { 0 } ::= { wfDlsPeerEntry 27 } wfDlsPeerNonPeakInBurstSize OBJECT-TYPE SYNTAX INTEGER ACCESS read-write STATUS mandatory DESCRIPTION "Burst Size amount for the incoming DLSw traffic, to use in RSVP reservations for this peer during non-peak hours" DEFVAL { 0 } ::= { wfDlsPeerEntry 28 } wfDlsPeerNonPeakStartTime OBJECT-TYPE SYNTAX INTEGER ACCESS read-write STATUS mandatory DESCRIPTION "Start time of the non-peak hours in hhmm format and 24 hour clock. If start time is greater in value than end time, non-peak hours ends the next day." DEFVAL { 0 } ::= { wfDlsPeerEntry 29 } wfDlsPeerNonPeakEndTime OBJECT-TYPE SYNTAX INTEGER ACCESS read-write STATUS mandatory DESCRIPTION "End time of the non-peak hours in hhmm 24 hour clock format" DEFVAL { 0 } ::= { wfDlsPeerEntry 30 } wfDlsPeerNonPeakStartDays OBJECT-TYPE SYNTAX Counter ACCESS read-write STATUS mandatory DESCRIPTION "Bitmap of the starting days of the week for a non-peak reservations. The MSBit represents Sunday, the next most significant bit represents Monday, and so on... Default is 0 - non-peak parameters are not used." ::= { wfDlsPeerEntry 31 } wfDlsPeerBackupOutBandwidth OBJECT-TYPE SYNTAX INTEGER(0..2147483647) ACCESS read-write STATUS mandatory DESCRIPTION "Bandwidth amount for the outgoing DLSw traffic, to use in RSVP reservations for the backup peer" DEFVAL { 0 } ::= { wfDlsPeerEntry 32 } wfDlsPeerBackupOutBurstSize OBJECT-TYPE SYNTAX INTEGER(0..2147483647) ACCESS read-write STATUS mandatory DESCRIPTION "Burst Size amount for the outgoing DLSw traffic, to use in RSVP reservations for the backup peer" DEFVAL { 0 } ::= { wfDlsPeerEntry 33 } wfDlsPeerBackupInBandwidth OBJECT-TYPE SYNTAX INTEGER(0..2147483647) ACCESS read-write STATUS mandatory DESCRIPTION "Bandwidth amount for the incoming DLSw traffic, to use in RSVP reservations for the backup peer" DEFVAL { 0 } ::= { wfDlsPeerEntry 34 } wfDlsPeerBackupInBurstSize OBJECT-TYPE SYNTAX INTEGER(0..2147483647) ACCESS read-write STATUS mandatory DESCRIPTION "Burst Size amount for the incoming DLSw traffic, to use in RSVP reservations for the backup peer" DEFVAL { 0 } ::= { wfDlsPeerEntry 35 } wfDlsConnectionTable OBJECT-TYPE SYNTAX SEQUENCE OF WfDlsConnectionEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "A table that contains the information about the current DLSw connections in progress. inst_id[15] = wfDlsConnectionCct wfDlsConnectionSrcMac wfDlsConnectionDstMac wfDlsConnectionSaps" ::= { wfDlsGroup 6 } wfDlsConnectionEntry OBJECT-TYPE SYNTAX WfDlsConnectionEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "An entry in wfDlsConnection" INDEX { wfDlsConnectionCct, wfDlsConnectionDstMac, wfDlsConnectionSrcMac, wfDlsConnectionSaps } ::= { wfDlsConnectionTable 1 } WfDlsConnectionEntry ::= SEQUENCE { wfDlsConnectionCct INTEGER, wfDlsConnectionDstMac OCTET STRING, wfDlsConnectionSrcMac OCTET STRING, wfDlsConnectionSaps OCTET STRING, wfDlsConnectionState INTEGER, wfDlsConnectionRemoteIpAddr IpAddress, wfDlsConnectionRemoteRxPort INTEGER, wfDlsConnectionLocalIpAddr IpAddress, wfDlsConnectionLocalTxPort INTEGER, wfDlsConnectionTxIFrames Counter, wfDlsConnectionRxIFrames Counter, wfDlsConnectionTxRnrs Counter, wfDlsConnectionRxRnrs Counter, wfDlsConnectionLocalBlockNum DisplayString, wfDlsConnectionLocalIdNum DisplayString, wfDlsConnectionLocalCpName DisplayString, wfDlsConnectionRif OCTET STRING, wfDlsConnectionRemoteBlockNum DisplayString, wfDlsConnectionRemoteIdNum DisplayString, wfDlsConnectionRemoteCpName DisplayString, wfDlsConnectionLocalDLCorr OCTET STRING, wfDlsConnectionKilled INTEGER, wfDlsConnectionRemoteDLCorr OCTET STRING } wfDlsConnectionCct OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The circuit this from which this connection originated" ::= { wfDlsConnectionEntry 1 } wfDlsConnectionDstMac OBJECT-TYPE SYNTAX OCTET STRING (SIZE (6)) ACCESS read-only STATUS mandatory DESCRIPTION "The Destination MAC address (the LLC session target)" ::= { wfDlsConnectionEntry 2 } wfDlsConnectionSrcMac OBJECT-TYPE SYNTAX OCTET STRING (SIZE (6)) ACCESS read-only STATUS mandatory DESCRIPTION "The Source MAC address (the LLC session originator)" ::= { wfDlsConnectionEntry 3 } wfDlsConnectionSaps OBJECT-TYPE SYNTAX OCTET STRING (SIZE (2)) ACCESS read-only STATUS mandatory DESCRIPTION "The SAPs for this connection (DSAP, SSAP)" ::= { wfDlsConnectionEntry 4 } wfDlsConnectionState OBJECT-TYPE SYNTAX INTEGER { connect(1), ccestab(2), notconn(3) } ACCESS read-only STATUS mandatory DESCRIPTION "The DLSw state of this connection. These are the steady states of the DLSw state machine. Transition states are not reflected" DEFVAL { notconn } ::= { wfDlsConnectionEntry 5 } wfDlsConnectionRemoteIpAddr OBJECT-TYPE SYNTAX IpAddress ACCESS read-only STATUS mandatory DESCRIPTION "The IP address of the remote DLSw peer over which this connection is established" ::= { wfDlsConnectionEntry 6 } wfDlsConnectionRemoteRxPort OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The TCP receive port number of the remote DLSw peer over which this connection is established" ::= { wfDlsConnectionEntry 7 } wfDlsConnectionLocalIpAddr OBJECT-TYPE SYNTAX IpAddress ACCESS read-only STATUS mandatory DESCRIPTION "The IP address of the local DLSw peer over which this connection is established" ::= { wfDlsConnectionEntry 8 } wfDlsConnectionLocalTxPort OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The TCP transmit port number of the local DLSw peer over which this connection is established" ::= { wfDlsConnectionEntry 9 } wfDlsConnectionTxIFrames OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The number of Information frames transmitted from this switch to the remote DLSw switch" ::= { wfDlsConnectionEntry 10 } wfDlsConnectionRxIFrames OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The number of Information frames received at this switch from the remote DLSw switch" ::= { wfDlsConnectionEntry 11 } wfDlsConnectionTxRnrs OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The number of RNR frames transmitted from this switch to the remote DLSw switch" ::= { wfDlsConnectionEntry 12 } wfDlsConnectionRxRnrs OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The number of RNR frames received at this switch from the remote DLSw switch" ::= { wfDlsConnectionEntry 13 } wfDlsConnectionLocalBlockNum OBJECT-TYPE SYNTAX DisplayString ACCESS read-only STATUS mandatory DESCRIPTION "The block number is the first 3 hexadecimal digits of node identification field of local XID" ::= { wfDlsConnectionEntry 14 } wfDlsConnectionLocalIdNum OBJECT-TYPE SYNTAX DisplayString ACCESS read-only STATUS mandatory DESCRIPTION "The ID number is the last 5 hexadecimal digits of node identification field of local XID" ::= { wfDlsConnectionEntry 15 } wfDlsConnectionLocalCpName OBJECT-TYPE SYNTAX DisplayString ACCESS read-only STATUS mandatory DESCRIPTION "The local CP name" ::= { wfDlsConnectionEntry 16 } wfDlsConnectionRif OBJECT-TYPE SYNTAX OCTET STRING ACCESS read-only STATUS mandatory DESCRIPTION "The Rif information" ::= { wfDlsConnectionEntry 17 } wfDlsConnectionRemoteBlockNum OBJECT-TYPE SYNTAX DisplayString ACCESS read-only STATUS mandatory DESCRIPTION "The block number is the first 3 hexadecimal digits of node identification field of remote XID" ::= { wfDlsConnectionEntry 18 } wfDlsConnectionRemoteIdNum OBJECT-TYPE SYNTAX DisplayString ACCESS read-only STATUS mandatory DESCRIPTION "The ID number is the last 5 hexadecimal digits of node identification field of remote XID" ::= { wfDlsConnectionEntry 19 } wfDlsConnectionRemoteCpName OBJECT-TYPE SYNTAX DisplayString ACCESS read-only STATUS mandatory DESCRIPTION "The remote CP name" ::= { wfDlsConnectionEntry 20 } wfDlsConnectionLocalDLCorr OBJECT-TYPE SYNTAX OCTET STRING (SIZE (4)) ACCESS read-only STATUS mandatory DESCRIPTION "The local Data Link Correlator for this DLSw circuit" ::= { wfDlsConnectionEntry 21 } wfDlsConnectionKilled OBJECT-TYPE SYNTAX INTEGER { alive(1), dead(2) } ACCESS read-write STATUS mandatory DESCRIPTION "Set to Dead to delete a connection" DEFVAL { alive } ::= { wfDlsConnectionEntry 22 } wfDlsConnectionRemoteDLCorr OBJECT-TYPE SYNTAX OCTET STRING (SIZE (4)) ACCESS read-only STATUS mandatory DESCRIPTION "The remote Data Link Correlator for this DLSw circuit" ::= { wfDlsConnectionEntry 23 } wfDlsNbTable OBJECT-TYPE SYNTAX SEQUENCE OF WfDlsNbEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "The DLSw NetBIOS name cache table. inst_id[16] = wfDlsNbName" ::= { wfDlsGroup 7 } wfDlsNbEntry OBJECT-TYPE SYNTAX WfDlsNbEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "An entry in wfDlsNb" INDEX { wfDlsNbName } ::= { wfDlsNbTable 1 } WfDlsNbEntry ::= SEQUENCE { wfDlsNbName OCTET STRING, wfDlsNbPeerIpAddr IpAddress, wfDlsNbCapablePeerIpAddr IpAddress, wfDlsNbQueries Counter } wfDlsNbName OBJECT-TYPE SYNTAX OCTET STRING (SIZE (16)) ACCESS read-only STATUS mandatory DESCRIPTION "The NetBIOS name of the remote station. Names that are shorter than 16 characters are padded with ASCII spaces (0x20)" ::= { wfDlsNbEntry 1 } wfDlsNbPeerIpAddr OBJECT-TYPE SYNTAX IpAddress ACCESS read-only STATUS mandatory DESCRIPTION "The IP address of the DLSw peer for this NetBIOS name" ::= { wfDlsNbEntry 2 } wfDlsNbCapablePeerIpAddr OBJECT-TYPE SYNTAX IpAddress ACCESS read-only STATUS mandatory DESCRIPTION "The IP address of the DLSw peer for a capable NetBIOS name" ::= { wfDlsNbEntry 3 } wfDlsNbQueries OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The number of NETBIOS_NQ queries sent for this name" ::= { wfDlsNbEntry 4 } wfDlsMacTable OBJECT-TYPE SYNTAX SEQUENCE OF WfDlsMacEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "The DLSw MAC address cache table. inst_id[6] = wfDlsMacAddr" ::= { wfDlsGroup 8 } wfDlsMacEntry OBJECT-TYPE SYNTAX WfDlsMacEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "An entry in wfDlsMac" INDEX { wfDlsMacAddr } ::= { wfDlsMacTable 1 } WfDlsMacEntry ::= SEQUENCE { wfDlsMacAddr OCTET STRING, wfDlsMacPeerIpAddr IpAddress, wfDlsMacCapablePeerIpAddr IpAddress, wfDlsMacQueries Counter } wfDlsMacAddr OBJECT-TYPE SYNTAX OCTET STRING (SIZE (6)) ACCESS read-only STATUS mandatory DESCRIPTION "The MAC address of the remote station" ::= { wfDlsMacEntry 1 } wfDlsMacPeerIpAddr OBJECT-TYPE SYNTAX IpAddress ACCESS read-only STATUS mandatory DESCRIPTION "The IP address of the DLSw peer for this MAC address" ::= { wfDlsMacEntry 2 } wfDlsMacCapablePeerIpAddr OBJECT-TYPE SYNTAX IpAddress ACCESS read-only STATUS mandatory DESCRIPTION "The IP address of the DLSw peer for a capable MAC address" ::= { wfDlsMacEntry 3 } wfDlsMacQueries OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The number of CANUREACH queries sent for this name" ::= { wfDlsMacEntry 4 } wfDlsTrafficFilterTable OBJECT-TYPE SYNTAX SEQUENCE OF WfDlsTrafficFilterEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "DLSw Traffic Filters" ::= { wfDlsGroup 9 } wfDlsTrafficFilterEntry OBJECT-TYPE SYNTAX WfDlsTrafficFilterEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "An entry in WfDlsTrafficFilterTable" INDEX { wfDlsTrafficFilterCircuit, wfDlsTrafficFilterRuleNumber, wfDlsTrafficFilterFragment } ::= { wfDlsTrafficFilterTable 1 } WfDlsTrafficFilterEntry ::= SEQUENCE { wfDlsTrafficFilterCreate INTEGER, wfDlsTrafficFilterEnable INTEGER, wfDlsTrafficFilterStatus INTEGER, wfDlsTrafficFilterCounter Counter, wfDlsTrafficFilterDefinition OCTET STRING, wfDlsTrafficFilterReserved INTEGER, wfDlsTrafficFilterCircuit INTEGER, wfDlsTrafficFilterRuleNumber INTEGER, wfDlsTrafficFilterFragment INTEGER, wfDlsTrafficFilterName DisplayString } wfDlsTrafficFilterCreate OBJECT-TYPE SYNTAX INTEGER { created(1), deleted(2) } ACCESS read-write STATUS mandatory DESCRIPTION "Defines the existence of the traffic filter rule: created - traffic filter exists delete - traffic filter does not exist and can be deleted" DEFVAL { created } ::= { wfDlsTrafficFilterEntry 1 } wfDlsTrafficFilterEnable OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } ACCESS read-write STATUS mandatory DESCRIPTION "Defines whether or not the traffic filter rule should be used: enabled - activate the rule. disabled - inactivate the rule" DEFVAL { enabled } ::= { wfDlsTrafficFilterEntry 2 } wfDlsTrafficFilterStatus OBJECT-TYPE SYNTAX INTEGER { active(1), error(2), inactive(3) } ACCESS read-only STATUS mandatory DESCRIPTION "Defines the current status of the traffic filter: inactive - the rule is not in use. active - the rule is being used. error - the application detected an error in the rule" DEFVAL { inactive } ::= { wfDlsTrafficFilterEntry 3 } wfDlsTrafficFilterCounter OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The number of received packets that have matched this rule" ::= { wfDlsTrafficFilterEntry 4 } wfDlsTrafficFilterDefinition OBJECT-TYPE SYNTAX OCTET STRING ACCESS read-write STATUS mandatory DESCRIPTION "The filter rule definition" ::= { wfDlsTrafficFilterEntry 5 } wfDlsTrafficFilterReserved OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Reserved field" ::= { wfDlsTrafficFilterEntry 6 } wfDlsTrafficFilterCircuit OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The ID of the Bridge Circuit to which the filter is applied" ::= { wfDlsTrafficFilterEntry 7 } wfDlsTrafficFilterRuleNumber OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "ID for the rule" ::= { wfDlsTrafficFilterEntry 8 } wfDlsTrafficFilterFragment OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Fragment number - for large rules" ::= { wfDlsTrafficFilterEntry 9 } wfDlsTrafficFilterName OBJECT-TYPE SYNTAX DisplayString ACCESS read-write STATUS mandatory DESCRIPTION "name of the rule number" ::= { wfDlsTrafficFilterEntry 10 } wfDlsDefaultMacTable OBJECT-TYPE SYNTAX SEQUENCE OF WfDlsDefaultMacEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "A table that contains DLSw Peer IP addresses for statically defined remote MAC addresses. The IP address in this table will always be used for CANUREACH messages to the remote MAC address. inst_id[6] = wfDlsDefaultMacAddr" ::= { wfDlsGroup 10 } wfDlsDefaultMacEntry OBJECT-TYPE SYNTAX WfDlsDefaultMacEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "An entry in wfDlsNbName" INDEX { wfDlsDefaultMacAddr } ::= { wfDlsDefaultMacTable 1 } WfDlsDefaultMacEntry ::= SEQUENCE { wfDlsDefaultMacDelete INTEGER, wfDlsDefaultMacAddr OCTET STRING, wfDlsDefaultMacPeerIp IpAddress } wfDlsDefaultMacDelete OBJECT-TYPE SYNTAX INTEGER { created(1), deleted(2) } ACCESS read-write STATUS mandatory DESCRIPTION "Create/Delete parameter. Default is created. Users perform an SNMP SET operation on this object in order to create/delete a DLSw Default MAC record" DEFVAL { created } ::= { wfDlsDefaultMacEntry 1 } wfDlsDefaultMacAddr OBJECT-TYPE SYNTAX OCTET STRING (SIZE (6)) ACCESS read-only STATUS mandatory DESCRIPTION "The MAC address of the destination station" ::= { wfDlsDefaultMacEntry 2 } wfDlsDefaultMacPeerIp OBJECT-TYPE SYNTAX IpAddress ACCESS read-write STATUS mandatory DESCRIPTION "The peer IP address to use for this MAC address" ::= { wfDlsDefaultMacEntry 3 } wfDlsDefaultNbTable OBJECT-TYPE SYNTAX SEQUENCE OF WfDlsDefaultNbEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "A table that contains DLSw Peer IP addresses for statically defined remote NetBIOS names. The IP address in this table will always be used for CANUREACH messages to the remote NetBIOS name. inst_id[16] = wfDlsDefaultNbName" ::= { wfDlsGroup 11 } wfDlsDefaultNbEntry OBJECT-TYPE SYNTAX WfDlsDefaultNbEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "An entry in wfDlsDefaultNb" INDEX { wfDlsDefaultNbName } ::= { wfDlsDefaultNbTable 1 } WfDlsDefaultNbEntry ::= SEQUENCE { wfDlsDefaultNbDelete INTEGER, wfDlsDefaultNbName OCTET STRING, wfDlsDefaultNbPeerIp IpAddress } wfDlsDefaultNbDelete OBJECT-TYPE SYNTAX INTEGER { created(1), deleted(2) } ACCESS read-write STATUS mandatory DESCRIPTION "Create/Delete parameter. Default is created. Users perform an SNMP SET operation on this object in order to create/delete a DLSw Default NetBIOS record" DEFVAL { created } ::= { wfDlsDefaultNbEntry 1 } wfDlsDefaultNbName OBJECT-TYPE SYNTAX OCTET STRING (SIZE (16)) ACCESS read-only STATUS mandatory DESCRIPTION "The NetBIOS name of the destination station" ::= { wfDlsDefaultNbEntry 2 } wfDlsDefaultNbPeerIp OBJECT-TYPE SYNTAX IpAddress ACCESS read-write STATUS mandatory DESCRIPTION "The peer IP address to use for this NetBIOS name" ::= { wfDlsDefaultNbEntry 3 } wfDlsLocalDeviceTable OBJECT-TYPE SYNTAX SEQUENCE OF WfDlsLocalDeviceEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "The configuration table for devices locally terminated through DLSw" ::= { wfDlsGroup 12 } wfDlsLocalDeviceEntry OBJECT-TYPE SYNTAX WfDlsLocalDeviceEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "An entry in the DLSw Local Device table" INDEX { wfDlsLocalDeviceCct, wfDlsLocalDeviceAddr } ::= { wfDlsLocalDeviceTable 1 } WfDlsLocalDeviceEntry ::= SEQUENCE { wfDlsLocalDeviceDelete INTEGER, wfDlsLocalDeviceDisable INTEGER, wfDlsLocalDeviceState INTEGER, wfDlsLocalDeviceCct INTEGER, wfDlsLocalDeviceAddr INTEGER, wfDlsLocalDeviceSourceMac OCTET STRING, wfDlsLocalDeviceSourceSap INTEGER, wfDlsLocalDeviceDestMac OCTET STRING, wfDlsLocalDeviceDestSap INTEGER, wfDlsLocalDeviceXidValue OCTET STRING, wfDlsLocalDeviceCanureachTimer INTEGER, wfDlsLocalDeviceCanureachRetries Gauge, wfDlsLocalDeviceLSTimer INTEGER, wfDlsLocalDeviceLSRetries Gauge, wfDlsLocalDeviceRcvCredit INTEGER, wfDlsLocalDeviceTxCredit INTEGER, wfDlsLocalDeviceCurTimer2 INTEGER, wfDlsLocalDeviceCurRetries2 Gauge, wfDlsLocalDeviceEnableXidPassthru INTEGER, wfDlsLocalDeviceActivationSequence INTEGER } wfDlsLocalDeviceDelete OBJECT-TYPE SYNTAX INTEGER { created(1), deleted(2) } ACCESS read-write STATUS mandatory DESCRIPTION "Create/Delete parameter. Default is created. Users perform an SNMP SET operation on this object in order to create/delete a DLSw Local Device" DEFVAL { created } ::= { wfDlsLocalDeviceEntry 1 } wfDlsLocalDeviceDisable OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } ACCESS read-write STATUS mandatory DESCRIPTION "Enable/Disable parameter. Default is enabled. Users perform an SNMP SET operation on this object in order to enable/disable a DLSw Local Device" DEFVAL { enabled } ::= { wfDlsLocalDeviceEntry 2 } wfDlsLocalDeviceState OBJECT-TYPE SYNTAX INTEGER { up(1), down(2), init(3), notpresent(4) } ACCESS read-only STATUS mandatory DESCRIPTION "The current state of DLSw" DEFVAL { notpresent } ::= { wfDlsLocalDeviceEntry 3 } wfDlsLocalDeviceCct OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The circuit on which this device is configured. Valid range (1-1023)" ::= { wfDlsLocalDeviceEntry 4 } wfDlsLocalDeviceAddr OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The physical address for this device. Valid range is based on media" ::= { wfDlsLocalDeviceEntry 5 } wfDlsLocalDeviceSourceMac OBJECT-TYPE SYNTAX OCTET STRING ACCESS read-write STATUS mandatory DESCRIPTION "The source MAC address of an emulated Token Ring end station for this device. Values are standard MSB Token Ring MAC addresses" ::= { wfDlsLocalDeviceEntry 6 } wfDlsLocalDeviceSourceSap OBJECT-TYPE SYNTAX INTEGER(0..254) ACCESS read-write STATUS mandatory DESCRIPTION "The source SAP of an emulated Token Ring end station for this device. Values are standard SNA SAPs" DEFVAL { 4 } ::= { wfDlsLocalDeviceEntry 7 } wfDlsLocalDeviceDestMac OBJECT-TYPE SYNTAX OCTET STRING ACCESS read-write STATUS mandatory DESCRIPTION "The destination MAC address for this device. Values are standard MSB Token Ring MAC addresses" ::= { wfDlsLocalDeviceEntry 8 } wfDlsLocalDeviceDestSap OBJECT-TYPE SYNTAX INTEGER(0..254) ACCESS read-write STATUS mandatory DESCRIPTION "The destination SAP for this device. Values are standard SNA SAPs" DEFVAL { 4 } ::= { wfDlsLocalDeviceEntry 9 } wfDlsLocalDeviceXidValue OBJECT-TYPE SYNTAX OCTET STRING ACCESS read-write STATUS mandatory DESCRIPTION "The station XID value. Value must match the IDBLK and IDNUM on the host" ::= { wfDlsLocalDeviceEntry 10 } wfDlsLocalDeviceCanureachTimer OBJECT-TYPE SYNTAX INTEGER(0..3600) ACCESS read-write STATUS mandatory DESCRIPTION "The time interval in seconds that a canureach is sent to the remote DLS peer to establish a session. A minimum value of 1 means that a canureach will be transmitted once a second, a maximum value of 3600 means that a canureach will be transmitted once an hour, and a value of 0 means that no canureach will be transmitted" DEFVAL { 30 } ::= { wfDlsLocalDeviceEntry 11 } wfDlsLocalDeviceCanureachRetries OBJECT-TYPE SYNTAX Gauge(0..4294967295) ACCESS read-write STATUS mandatory DESCRIPTION "The maximum number of times a canureach is sent to the remote DLS peer to establish a session. A minimum value of 0 means that no canureach messages will be transmitted, a maximum value of 0xFFFFFFFF means that an infinite number of canureach messages will be transmitted for this connection. The default is set to 10" DEFVAL { 10 } ::= { wfDlsLocalDeviceEntry 12 } wfDlsLocalDeviceLSTimer OBJECT-TYPE SYNTAX INTEGER(0..3600) ACCESS read-write STATUS mandatory DESCRIPTION "The time interval in seconds that a connect request is sent to the local SDLC device to establish a session. A minimum value of 1 means that a connect request will be sent once a second, a maximum value of 3600 means that a connect request will be sent once an hour, and a value of 0 means that no connect requests will be sent" DEFVAL { 30 } ::= { wfDlsLocalDeviceEntry 13 } wfDlsLocalDeviceLSRetries OBJECT-TYPE SYNTAX Gauge(0..4294967295) ACCESS read-write STATUS mandatory DESCRIPTION "The maximum number of times a connect request is sent to the local SDLC device to establish a session. A minimum value of 0 means that no connect requests will be sent, a maximum value of 0xFFFFFFFF means that an infinite number of connect requests will be sent for this connection. The default is set to 10" DEFVAL { 10 } ::= { wfDlsLocalDeviceEntry 14 } wfDlsLocalDeviceRcvCredit OBJECT-TYPE SYNTAX INTEGER(0..200) ACCESS read-write STATUS mandatory DESCRIPTION "Receive credit count. Maximum number of frames SDLC is allowed to send to DLS. A minimum value of 1 means that DLS will only accept up to 1 frame from SDLC before it updates SDLCs credit. A value of 0 means that DLS can receive an infinite number of frames from SDLC without the need to update SDLC's credit" DEFVAL { 10 } ::= { wfDlsLocalDeviceEntry 15 } wfDlsLocalDeviceTxCredit OBJECT-TYPE SYNTAX INTEGER(0..200) ACCESS read-write STATUS mandatory DESCRIPTION "Transmit credit count. Maximum number of frames DLS is allowed to send to SDLC. A minimum value of 1 means that DLS can only send one frame to SDLC until it receives credit update from SDLC. A value of 0 means that DLS can send an infinite number of frames to SDLC without the need to update SDLC's credit" DEFVAL { 10 } ::= { wfDlsLocalDeviceEntry 16 } wfDlsLocalDeviceCurTimer2 OBJECT-TYPE SYNTAX INTEGER(0..2147483647) ACCESS read-write STATUS mandatory DESCRIPTION "The time interval in seconds that a canureach is sent to the remote DLS peer to establish a session. A minimum value of 1 means that a canureach will be transmitted once a second, a maximum value means that a canureach will be transmitted once every timer2 seconds, and a value of 0 means that no canureach will be transmitted" DEFVAL { 30 } ::= { wfDlsLocalDeviceEntry 17 } wfDlsLocalDeviceCurRetries2 OBJECT-TYPE SYNTAX Gauge(0..4294967295) ACCESS read-write STATUS mandatory DESCRIPTION "The maximum number of times a canureach is sent to the remote DLS peer to establish a session. A minimum value of 0 means that no canureach messages will be transmitted, a maximum value of 0xFFFFFFFF means that an infinite number of canureach messages will be transmitted for this connection. The default is set to infinite: 4294967295 = 0xFFFFFFFF" DEFVAL { 4294967295 } ::= { wfDlsLocalDeviceEntry 18 } wfDlsLocalDeviceEnableXidPassthru OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } ACCESS read-write STATUS mandatory DESCRIPTION "XID passthru Enable/Disable parameter. Default is enabled. Used for pu2.1 circuits to allow the XID to be passed thru to SDLC when host is connected to token ring and remote is SDLC." DEFVAL { disabled } ::= { wfDlsLocalDeviceEntry 19 } wfDlsLocalDeviceActivationSequence OBJECT-TYPE SYNTAX INTEGER { localdevicefirst(1), peerfirst(2) } ACCESS read-write STATUS mandatory DESCRIPTION "Sequence of activation for SDLC PU2.0 fixed format primary devices. LocalDeviceFirst specifies that DLS establishes a connection with the SDLC End Station first. Once the Local Device successfully responds, DLS then starts up the SSP connection to the peer. PeerFirst specifies that DLS starts the SSP connection first, and contacts the SDLC End Station only after receiving a CONTACT message from the peer. " DEFVAL { localdevicefirst } ::= { wfDlsLocalDeviceEntry 20 } wfDlsLocalCircuitTable OBJECT-TYPE SYNTAX SEQUENCE OF WfDlsLocalCircuitEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "communicate with each other via a virtual circuit gate" ::= { wfDlsGroup 13 } wfDlsLocalCircuitEntry OBJECT-TYPE SYNTAX WfDlsLocalCircuitEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "An entry in the DLSw Local Circuit table" INDEX { wfDlsLocalCircuitCct } ::= { wfDlsLocalCircuitTable 1 } WfDlsLocalCircuitEntry ::= SEQUENCE { wfDlsLocalCircuitDelete INTEGER, wfDlsLocalCircuitDisable INTEGER, wfDlsLocalCircuitState INTEGER, wfDlsLocalCircuitCct INTEGER, wfDlsLocalCircuitClientCount INTEGER, wfDlsLocalCircuitFrameCount INTEGER, wfDlsLocalCircuitSlot INTEGER, wfDlsLocalCctDefaultMac OCTET STRING } wfDlsLocalCircuitDelete OBJECT-TYPE SYNTAX INTEGER { created(1), deleted(2) } ACCESS read-write STATUS mandatory DESCRIPTION "Create/Delete parameter" DEFVAL { created } ::= { wfDlsLocalCircuitEntry 1 } wfDlsLocalCircuitDisable OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } ACCESS read-write STATUS mandatory DESCRIPTION "Disable parameter" DEFVAL { enabled } ::= { wfDlsLocalCircuitEntry 2 } wfDlsLocalCircuitState OBJECT-TYPE SYNTAX INTEGER { up(1), down(2) } ACCESS read-only STATUS mandatory DESCRIPTION "Circuit state" DEFVAL { down } ::= { wfDlsLocalCircuitEntry 3 } wfDlsLocalCircuitCct OBJECT-TYPE SYNTAX INTEGER ACCESS read-write STATUS mandatory DESCRIPTION "Local Circuit ID" ::= { wfDlsLocalCircuitEntry 4 } wfDlsLocalCircuitClientCount OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Number of clients registerd" ::= { wfDlsLocalCircuitEntry 5 } wfDlsLocalCircuitFrameCount OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Total number of frames passed" ::= { wfDlsLocalCircuitEntry 6 } wfDlsLocalCircuitSlot OBJECT-TYPE SYNTAX INTEGER ACCESS read-write STATUS mandatory DESCRIPTION "Slot on which this cct resides" ::= { wfDlsLocalCircuitEntry 7 } wfDlsLocalCctDefaultMac OBJECT-TYPE SYNTAX OCTET STRING ACCESS read-write STATUS mandatory DESCRIPTION "Default Mac address associated with this circuit" ::= { wfDlsLocalCircuitEntry 8 } wfDlsGenToolTable OBJECT-TYPE SYNTAX SEQUENCE OF WfDlsGenToolEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "A table that contains the Gen Tool characteristics to be used on Bay Network Routers. inst_id[1] = wfDlsSlotNumber" ::= { wfDlsGroup 14 } wfDlsGenToolEntry OBJECT-TYPE SYNTAX WfDlsGenToolEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "An characteristics for wfDlsGenTool" INDEX { wfDlsSlotNumber } ::= { wfDlsGenToolTable 1 } WfDlsGenToolEntry ::= SEQUENCE { wfDlsGenDelete INTEGER, wfDlsGenDisable INTEGER, wfDlsGenDefaultSessions INTEGER, wfDlsGenStartupTime INTEGER, wfDlsGenIFramePerSec INTEGER, wfDlsGenMacAddrOffset INTEGER, wfDlsGenVariableDstMAC INTEGER, wfDlsGenDefaultUpperMAC INTEGER, wfDlsGenDataLength INTEGER, wfDlsGenNumSapPerMac INTEGER, wfDlsGenSapIncrement INTEGER } wfDlsGenDelete OBJECT-TYPE SYNTAX INTEGER { created(1), deleted(2) } ACCESS read-write STATUS mandatory DESCRIPTION "Create/Delete parameter. Default is created." DEFVAL { created } ::= { wfDlsGenToolEntry 1 } wfDlsGenDisable OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } ACCESS read-write STATUS mandatory DESCRIPTION "Enable/Disable parameter. Default is disabled. Users perform an SNMP SET operation on this object in order to enable/disable DLSw Generat or " DEFVAL { disabled } ::= { wfDlsGenToolEntry 2 } wfDlsGenDefaultSessions OBJECT-TYPE SYNTAX INTEGER(5..10000) ACCESS read-write STATUS mandatory DESCRIPTION "Number of DLSw Generator Sessions to be brought up if specific numbers are not configured per slot." DEFVAL { 250 } ::= { wfDlsGenToolEntry 3 } wfDlsGenStartupTime OBJECT-TYPE SYNTAX INTEGER(50..100000) ACCESS read-write STATUS mandatory DESCRIPTION "Time between connection setup requests in milliseconds." DEFVAL { 1000 } ::= { wfDlsGenToolEntry 4 } wfDlsGenIFramePerSec OBJECT-TYPE SYNTAX INTEGER(0..5000) ACCESS read-write STATUS mandatory DESCRIPTION "Number of I frames to be sent per second." DEFVAL { 256 } ::= { wfDlsGenToolEntry 5 } wfDlsGenMacAddrOffset OBJECT-TYPE SYNTAX INTEGER(0..5000) ACCESS read-write STATUS mandatory DESCRIPTION "Offset for MAC addresses to be created for GEN." DEFVAL { 0 } ::= { wfDlsGenToolEntry 6 } wfDlsGenVariableDstMAC OBJECT-TYPE SYNTAX INTEGER{ enabled(1), disabled(2) } ACCESS read-write STATUS mandatory DESCRIPTION "Allows varying destination MAC address." DEFVAL { disabled } ::= { wfDlsGenToolEntry 7 } wfDlsGenDefaultUpperMAC OBJECT-TYPE SYNTAX INTEGER(0..2147418112) ACCESS read-write STATUS mandatory DESCRIPTION "Allows varying upper MAC address." DEFVAL { 1079705600 } ::= {wfDlsGenToolEntry 8 } wfDlsGenDataLength OBJECT-TYPE SYNTAX INTEGER(0..2052) ACCESS read-write STATUS mandatory DESCRIPTION "Gen data frame size" DEFVAL { 250 } ::= { wfDlsGenToolEntry 9 } wfDlsGenNumSapPerMac OBJECT-TYPE SYNTAX INTEGER(1..255) ACCESS read-write STATUS mandatory DESCRIPTION "Gen number of saps for each mac" DEFVAL { 1 } ::= { wfDlsGenToolEntry 10 } wfDlsGenSapIncrement OBJECT-TYPE SYNTAX INTEGER(1..100) ACCESS read-write STATUS mandatory DESCRIPTION "Gen sap incremental value" DEFVAL { 4 } ::= { wfDlsGenToolEntry 11 } wfDlsMcastIpTable OBJECT-TYPE SYNTAX SEQUENCE OF WfDlsMcastIpEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "A table that contains the Multicast IP addresses that will be used by DLSw ro send and receive explorer traffic." ::= { wfDlsGroup 15 } wfDlsMcastIpEntry OBJECT-TYPE SYNTAX WfDlsMcastIpEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "An entry in the wfDlsMcastIpTable" INDEX { wfDlsMcastIpAddr } ::= { wfDlsMcastIpTable 1 } WfDlsMcastIpEntry ::= SEQUENCE { wfDlsMcastIpDelete INTEGER, wfDlsMcastIpState INTEGER, wfDlsMcastIpAddr IpAddress, wfDlsMcastIpSlots Gauge, wfDlsMcastIpBackupConfig INTEGER, wfDlsMcastIpBackupIpAddr IpAddress, wfDlsMcastIpBackupMaxUpTime INTEGER, wfDlsMcastIpBackupHoldDownTime INTEGER, wfDlsMcastIpBackupStartTime INTEGER, wfDlsMcastIpBackupEndTime INTEGER, wfDlsMcastIpBackupType INTEGER } wfDlsMcastIpDelete OBJECT-TYPE SYNTAX INTEGER { created(1), deleted(2) } ACCESS read-write STATUS mandatory DESCRIPTION "Create/Delete parameter. Default is created. Users perform an SNMP SET operation on this object in order to create/delete a DLSw multicast IP record" DEFVAL { created } ::= { wfDlsMcastIpEntry 1 } wfDlsMcastIpState OBJECT-TYPE SYNTAX INTEGER { active(1), inactive(2), notpresent(3) } ACCESS read-only STATUS mandatory DESCRIPTION "The current state of this DLSw McastIpEntry. Active indicates that it is possible to accept or sent CURs to/from the multicast IP group address specified in this entry. Inactive indicates that DLSw in not a member of this multicast IP group. The initial state is notpresent and this state will be maintained until this mib record has been read." DEFVAL { notpresent } ::= { wfDlsMcastIpEntry 2 } wfDlsMcastIpAddr OBJECT-TYPE SYNTAX IpAddress ACCESS read-only STATUS mandatory DESCRIPTION "The Multicast IP address of this entry" ::= { wfDlsMcastIpEntry 3 } wfDlsMcastIpSlots OBJECT-TYPE SYNTAX Gauge(0..4294967295) ACCESS read-write STATUS mandatory DESCRIPTION "Bit mask field representing the slots upon which this DlsMcastIpEntry can receive and transmit multicast data. The MSBit represents slot 1, the next most significant bit represents slot 2, and so on... Slots can be 1-14. Default is all slots on a BCN." DEFVAL { 4294705152 } ::= { wfDlsMcastIpEntry 4 } wfDlsMcastIpBackupConfig OBJECT-TYPE SYNTAX INTEGER { yes(1), no(2) } ACCESS read-write STATUS mandatory DESCRIPTION "The indication of whether or not a backup peer is to be configured for the primary peer. The default is no which means that there is no backup peer configured by default." DEFVAL { no } ::= { wfDlsMcastIpEntry 5 } wfDlsMcastIpBackupIpAddr OBJECT-TYPE SYNTAX IpAddress ACCESS read-write STATUS mandatory DESCRIPTION "The IP Address of the backup DLSw peer." ::= { wfDlsMcastIpEntry 6 } wfDlsMcastIpBackupMaxUpTime OBJECT-TYPE SYNTAX INTEGER(0..999999) ACCESS read-write STATUS mandatory DESCRIPTION "The maximum amount of time (in seconds) allowed for a TCP connection to stay established to the backup DLSw peer. If set to zero, this feature is disabled. Set to anything greater than zero to enable the feature." DEFVAL { 0 } ::= { wfDlsMcastIpEntry 7 } wfDlsMcastIpBackupHoldDownTime OBJECT-TYPE SYNTAX INTEGER(0..2147483647) ACCESS read-write STATUS mandatory DESCRIPTION "The amount of time (in seconds) to wait before starting a new TCP connection to the backup DLSw peer." DEFVAL { 120 } ::= { wfDlsMcastIpEntry 8 } wfDlsMcastIpBackupStartTime OBJECT-TYPE SYNTAX INTEGER(0..2400) ACCESS read-write STATUS mandatory DESCRIPTION "Used in conjunction with the EndTime attribute. Together these define a time interval for when a backup peer can be active. The start time is the beginning time of day that a backup peer can be established. (HHMM format)" DEFVAL { 0001 } ::= { wfDlsMcastIpEntry 9 } wfDlsMcastIpBackupEndTime OBJECT-TYPE SYNTAX INTEGER(1..2400) ACCESS read-write STATUS mandatory DESCRIPTION "Used in conjunction with the StartTime attribute. Together these define a time interval for when a backup peer can be active. The end time is the end time of day that a backup peer can be established. If a backup peer is active and the current time is after this end time, the backup peer will be brought down. (HHMM format)" DEFVAL { 2400 } ::= { wfDlsMcastIpEntry 10 } wfDlsMcastIpBackupType OBJECT-TYPE SYNTAX INTEGER { multicast(1), v20udp(2), v20unknown(3), v20tcp(4), tcp1795(5) } ACCESS read-write STATUS mandatory DESCRIPTION "The type of this DLSw backup peer" DEFVAL { v20unknown } ::= { wfDlsMcastIpEntry 11 } wfDlsTranslateMacTable OBJECT-TYPE SYNTAX SEQUENCE OF WfDlsTranslateMacEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "A table that contains destination MAC addresses which can be replaced with another remote MAC addresses. These new MAC addresses will be used to establish SNA sessions instead of previously configured on end nodes." ::= { wfDlsGroup 16 } wfDlsTranslateMacEntry OBJECT-TYPE SYNTAX WfDlsTranslateMacEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "An entry in wfDlsTranslateMacTable" INDEX { wfDlsOriginDestMacAddr } ::= { wfDlsTranslateMacTable 1 } WfDlsTranslateMacEntry ::= SEQUENCE { wfDlsTranslateMacDelete INTEGER, wfDlsOriginDestMacAddr OCTET STRING, wfDlsTranslateDestMacAddr OCTET STRING } wfDlsTranslateMacDelete OBJECT-TYPE SYNTAX INTEGER { created(1), deleted(2) } ACCESS read-write STATUS mandatory DESCRIPTION "Create/Delete parameter. Translate is created." DEFVAL { created } ::= { wfDlsTranslateMacEntry 1 } wfDlsOriginDestMacAddr OBJECT-TYPE SYNTAX OCTET STRING (SIZE (6)) ACCESS read-only STATUS mandatory DESCRIPTION "The originally configured MAC address of the destination station" ::= { wfDlsTranslateMacEntry 2 } wfDlsTranslateDestMacAddr OBJECT-TYPE SYNTAX OCTET STRING (SIZE (6)) ACCESS read-write STATUS mandatory DESCRIPTION "The translated MAC address of the destination station" ::= { wfDlsTranslateMacEntry 3 } END -- Wellfleet-DLS-MIB