-- This file is corresponding to Release 6.3.1.100 from 2003/03/10 00:00:00 -- (C)opyright 1991-1999 BinTec Communications AG, All Rights Reserved -- $RCSfile: mibx21,v $ -- $Revision: 1.12 $ BIANCA-BRICK-X21-MIB DEFINITIONS ::= BEGIN IMPORTS Counter FROM RFC1155-SMI OBJECT-TYPE FROM RFC-1212; org OBJECT IDENTIFIER ::= { iso 3 } dod OBJECT IDENTIFIER ::= { org 6 } internet OBJECT IDENTIFIER ::= { dod 1 } private OBJECT IDENTIFIER ::= { internet 4 } enterprises OBJECT IDENTIFIER ::= { private 1 } bintec OBJECT IDENTIFIER ::= { enterprises 272 } bibo OBJECT IDENTIFIER ::= { bintec 4 } x21 OBJECT IDENTIFIER ::= { bibo 10 } -- Interfaces Group -- Management Information for the X21 Subsystem of the BIANCA/BRICK Date ::= INTEGER HexValue ::= INTEGER x21IfTable OBJECT-TYPE SYNTAX SEQUENCE OF X21IfEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "The x21IfTable contains information relating to the interfaces found on the system. Each entry corresponds to a connected X21 interface. Entries can only be added or deleted by the system. Creating entries: Entries are created by the system only when a new X21 module is installed. Deleting entries: Entries are removed by the system after the appropriate X21 module is removed." ::= { x21 1 } x21IfEntry OBJECT-TYPE SYNTAX X21IfEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "" INDEX { x21IfIndex } ::= { x21IfTable 1 } X21IfEntry ::= SEQUENCE { x21IfIndex INTEGER, x21IfL1State INTEGER, x21IfL1Mode INTEGER, x21IfIfLeads INTEGER, x21IfSpeed INTEGER, x21IfL2Mode INTEGER, x21IfBundle INTEGER, -- Statistics x21IfSpeedReal Counter, x21IfRxPackets Counter, x21IfRxOctets Counter, x21IfTxPackets Counter, x21IfTxOctets Counter, x21IfRxResets Counter, x21IfRxAborts Counter, x21IfRxOverruns Counter, x21IfRxCRCErrors Counter, x21IfRxGiantFrames Counter, x21IfTxResets Counter, x21IfTxAborts Counter, x21IfTxUnderruns Counter, x21IfTxGiantFrames Counter, x21IfIfReSyncs Counter } x21IfIndex OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Unique index of the X21 interface." ::= { x21IfEntry 1 } x21IfL1State OBJECT-TYPE SYNTAX INTEGER { dn(1), -- inactive up(2) -- active } ACCESS read-only STATUS mandatory DESCRIPTION "The X21 physical layer state dn(1) physical layer is inactive; up(2) physical layer is active;" ::= { x21IfEntry 2 } x21IfL1Mode OBJECT-TYPE SYNTAX INTEGER { dte(1), dce(2) } ACCESS read-write STATUS mandatory DESCRIPTION "The physical layer (layer 1) mode. When configured as DCE(2) the X21 interface provides the clock." ::= { x21IfEntry 3 } x21IfIfLeads OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } ACCESS read-write STATUS mandatory DESCRIPTION "The value of IfLeads has influence on the state of the physical layer (L1State). When configured as IfLeads=enabled(1), the state of the physical layer depends on the signals of the X.21 interface pins `Indication' and `Control'. When configured as IfLeads=disabled(2), the state of the physical layer stays always up." ::= { x21IfEntry 4 } x21IfSpeed OBJECT-TYPE SYNTAX INTEGER { s2048k(1), s1024k(2), s512k(3), s256k(4), s128k(5), s64000(6), s38400(7), s19200(8), s14400(9), s9600(10), s2400(11) } ACCESS read-write STATUS mandatory DESCRIPTION "The X21 interface speed in bits per second. The range can be configured between 2Mbits and 2400 Bits per second." ::= { x21IfEntry 5 } x21IfL2Mode OBJECT-TYPE SYNTAX INTEGER { dte(1), dce(2), auto(3) } ACCESS read-write STATUS mandatory DESCRIPTION "The layer 2 mode. This value has influence on the HDLC address field (first byte of a HDCL frame). When configured as DTE(1) the address in a command frame is 0x01, when configured as DCE(2) it is 0x03. For response frames it is vice versa. When configured as AUTO(3), layer 2 is set to the same mode like L1Mode is set." ::= { x21IfEntry 6 } x21IfSpeedReal OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "The measured X21 interface speed in bits per second." ::= { x21IfEntry 7 } x21IfRxPackets OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Count of received valid Frames." ::= { x21IfEntry 8 } x21IfRxOctets OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Count of received bytes." ::= { x21IfEntry 9 } x21IfTxPackets OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Count of transmitted valid Frames." ::= { x21IfEntry 10 } x21IfTxOctets OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Count of transmitted bytes." ::= { x21IfEntry 11 } x21IfRxResets OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Count of receiver resets. Under rare circumstances it might be necessary to reset the receiver to work properly." ::= { x21IfEntry 12 } x21IfRxAborts OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Count of receiver aborts. The sender of a frame can indicate a frame as aborted with a special Abort sequence." ::= { x21IfEntry 13 } x21IfRxOverruns OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Count of receiver overruns. If the X21 card is unable to grant sufficiently soon/often the bus, the 32-character RxFIFO may fill up. This leads to loss of data." ::= { x21IfEntry 14 } x21IfRxCRCErrors OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Count of corrupted frames. Errors due to interference on the X21 cable." ::= { x21IfEntry 15 } x21IfRxGiantFrames OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Count of received frames with illegal framesize. This can occur if a frame delimiter is destroyed." ::= { x21IfEntry 16 } x21IfTxResets OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Count of transmitter resets. Under rare circumstances it might be necessary to reset the transmitter to work properly." ::= { x21IfEntry 17 } x21IfTxAborts OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Count of transmitter aborts. While sending a frame it might be necessary to indicate this frame as aborted. In this case the receiver regards this frame as illegal." ::= { x21IfEntry 18 } x21IfTxUnderruns OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Count of transmitter underruns. The serial data for the X21 card is supplied too slowly." ::= { x21IfEntry 19 } x21IfTxGiantFrames OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Count of transmitted frames with illegal framesize. This can occur if an upper module creates packets with more than the maximum allowed packet size." ::= { x21IfEntry 20 } x21IfIfReSyncs OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Count of interface resynchronization. Under rare circumstances it might be necessary to resynchronize the physical interface to work properly." ::= { x21IfEntry 21 } x21IfBundle OBJECT-TYPE SYNTAX INTEGER (0..255) ACCESS read-write STATUS mandatory DESCRIPTION "Index of the bundle to aggregate multiple Channels to one interface." ::= { x21IfEntry 22 } END -- of BIANCA-BRICK definitions