-- ***************************************************************** -- Cisco VTP MIB -- -- February, 1997 Chris Young -- -- Copyright (c) 1996-2000 by cisco Systems, Inc. -- All rights reserved. -- ***************************************************************** CISCO-VTP-MIB DEFINITIONS ::= BEGIN IMPORTS MODULE-IDENTITY, OBJECT-TYPE, NOTIFICATION-TYPE, Counter32, IpAddress, Gauge32 FROM SNMPv2-SMI TEXTUAL-CONVENTION, RowStatus, DisplayString, DateAndTime, TruthValue, TestAndIncr FROM SNMPv2-TC InterfaceIndex, ifIndex FROM IF-MIB ciscoMgmt FROM CISCO-SMI -- MODULE-COMPLIANCE, OBJECT-GROUP, NOTIFICATION-GROUP MODULE-COMPLIANCE, OBJECT-GROUP FROM SNMPv2-CONF; ciscoVtpMIB MODULE-IDENTITY LAST-UPDATED "200004100000Z" ORGANIZATION "Cisco Systems, Inc." CONTACT-INFO "Cisco Systems Customer Service Postal: 170 W Tasman Drive San Jose, CA 95134 USA Tel: +1 800 553-NETS E-mail: cs-wbu@cisco.com" DESCRIPTION "The MIB module for entities implementing the VTP protocol." REVISION "200004100000Z" DESCRIPTION "Added 4k VLAN editing and Dot1qTunnel support" REVISION "200001060000Z" DESCRIPTION "Added 4k VLAN support" REVISION "9902251130Z" DESCRIPTION "Added import of NOTIFICATION-GROUP" REVISION "9901051130Z" DESCRIPTION "Added support for encapsulation type notApplicable" REVISION "9805191130Z" DESCRIPTION "Added support for encapsulation type negotiation" REVISION "9708081138Z" DESCRIPTION "Added Backup CRF object" REVISION "9705091130Z" DESCRIPTION "Added ARE and STE hop counts." REVISION "9702241115Z" DESCRIPTION "Added support for turning on VTP for Trunk cards." REVISION "9701271730Z" DESCRIPTION "Added support for version 2 features." REVISION "9609161230Z" DESCRIPTION "Updated the Token-Ring support." REVISION "9607171230Z" DESCRIPTION "Updated to include objects in support of VTP pruning." REVISION "9601181820Z" DESCRIPTION "Initial version of this MIB module." ::= { ciscoMgmt 46 } vtpMIBObjects OBJECT IDENTIFIER ::= { ciscoVtpMIB 1 } -- Textual Conventions VlanIndex ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "The VLAN-id of a VLAN on ISL trunks. Modification of default parameters is allowed. Implementations are allowed to restrict the range of VLANs. For entities support up to 1024 VLANS. VLANs above 1000 are reserved for default VLANs and future use. Modification of default parameters is allowed. Creation or deletion of VLANs above 1000 is not allowed." SYNTAX INTEGER (0..4095) ManagementDomainIndex ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "An arbitrary integer-value to uniquely identify a management domain on the local system." SYNTAX INTEGER (1..255) OwnerString ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "This data type is used to model an administratively assigned name of the owner of a resource. This information is taken from the NVT ASCII character set. It is suggested that this name contain one or more of the following: IP address, management station name, network manager's name, location, or phone number. In some cases the agent itself will be the owner of an entry. In these cases, this string shall be set to a string starting with 'monitor'. This definition is identical to that contained in RFC 1271." SYNTAX OCTET STRING VlanType ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "The type of a VLAN. Note that the 'ethernet' type, is used for any ethernet or 802.3 VLAN, including an ATM Ethernet ELAN; and the 'tokenRing' ('trCrf') type is used for each VLAN representing a single logical 802.5 ring including an ATM Token-Ring ELAN. The 'trCrf' type is used for token ring VLANs made up of (at most) one transparently bridged LAN segment. The 'trBrf' type is used for VLANs which represent the scope of many 'trCrf' VLANs all connected together via source route bridging. The token ring 'trBrf' can be said to represent the bridged broadcast domain." SYNTAX INTEGER { ethernet(1), fddi(2), tokenRing(3), -- also known as trCrf fddiNet(4), trNet(5), -- also known as trBrf deprecated(6) } VlanTypeExt ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "The additional type information of VLAN. vtpmanageable(0) An user defined VLAN which is manageable through VTP protocol. internal(1) An internal VLAN created by the device. Internal VLAN can not be created or deleted. Configuration of an internal VLAN is read only. reserved(2) A VLAN reserved by the device. Reserved VLAN can not be created or deleted. Configuration of an reserved VLAN is read only. " SYNTAX OCTET STRING(SIZE(1)) -- BITS { -- vtpmanageable(0), -- internal(1), -- reserved(2) -- } -- -- VTP status -- vtpStatus OBJECT IDENTIFIER ::= { vtpMIBObjects 1 } vtpVersion OBJECT-TYPE SYNTAX INTEGER { one(1), two(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "The version of VTP in use on the local system. A device will report its version capability and not any particular version in use on the device." ::= { vtpStatus 1 } vtpMaxVlanStorage OBJECT-TYPE SYNTAX INTEGER (-1..1023) MAX-ACCESS read-only STATUS current DESCRIPTION "An estimate of the maximum number of VLANs about which the local system can recover complete VTP information after a reboot. If the number of defined VLANs is greater than this value, then the system can not act as a VTP Server. For a device which has no means to calculate the estimated number, this value is -1." ::= { vtpStatus 2 } vtpNotificationsEnabled OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "An indication of whether the notifications/traps defined by the vtpConfigNotificationsGroup are enabled." ::= { vtpStatus 3 } -- -- VTP Management Domains -- vlanManagementDomains OBJECT IDENTIFIER ::= { vtpMIBObjects 2 } managementDomainTable OBJECT-TYPE SYNTAX SEQUENCE OF ManagementDomainEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table containing information on the management domains in which the local system is participating. Devices which support only one management domain will support just one row in this table, and will not let it be deleted nor let other rows be created. Devices which support multiple management domains will allow rows to be created and deleted, but will not allow the last row to be deleted." ::= { vlanManagementDomains 1 } managementDomainEntry OBJECT-TYPE SYNTAX ManagementDomainEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Information about the status of one management domain." INDEX { managementDomainIndex } ::= { managementDomainTable 1 } ManagementDomainEntry ::= SEQUENCE { managementDomainIndex ManagementDomainIndex, managementDomainName DisplayString, managementDomainLocalMode INTEGER, managementDomainConfigRevNumber Gauge32, managementDomainLastUpdater IpAddress, managementDomainLastChange DateAndTime, managementDomainRowStatus RowStatus, managementDomainTftpServer IpAddress, managementDomainTftpPathname DisplayString, managementDomainPruningState INTEGER, managementDomainVersionInUse INTEGER } managementDomainIndex OBJECT-TYPE SYNTAX ManagementDomainIndex MAX-ACCESS not-accessible STATUS current DESCRIPTION "An arbitrary value to uniquely identify the management domain on the local system." ::= { managementDomainEntry 1 } managementDomainName OBJECT-TYPE SYNTAX DisplayString (SIZE (0..32)) MAX-ACCESS read-create STATUS current DESCRIPTION "The management name of a domain in which the local system is participating. The zero-length name corresponds to the 'no management-domain' state which is the initial value at installation-time if not configured otherwise. Note that the zero-length name does not correspond to an operational management domain, and a device does not send VTP advertisements while in the 'no management-domain' state. A device leaves the 'no management-domain' state when it obtains a management-domain name, either through configuration or through inheriting the management-domain name from a received VTP advertisement. When the value of an existing instance of this object is modified by network management, the local system should re- initialize its VLAN information (for the given management domain) as if it had just been configured with a management domain name at installation time." ::= { managementDomainEntry 2 } managementDomainLocalMode OBJECT-TYPE SYNTAX INTEGER { client(1), server(2), transparent(3) } MAX-ACCESS read-create STATUS current DESCRIPTION "An indication of whether the local system is acting as a VTP Client or as a VTP Server in this management domain. The value 'transparent' is a read-only indication that a device is not supporting VTP for this VTP management domain, e.g., because the amount of VLAN information is too large for it to hold in DRAM." ::= { managementDomainEntry 3 } managementDomainConfigRevNumber OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "The current Configuration Revision Number as known by the local device for this management domain. This value is updated (if necessary) whenever a VTP advertisement is received or generated. When in the 'no management-domain' state, this value is 0." ::= { managementDomainEntry 4 } managementDomainLastUpdater OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The IP-address (or one of them) of the VTP Server which last updated the Configuration Revision Number, as indicated in the most recently received VTP advertisement for this management domain. Before an advertisement has been received, this value is 0.0.0.0." ::= { managementDomainEntry 5 } managementDomainLastChange OBJECT-TYPE SYNTAX DateAndTime MAX-ACCESS read-only STATUS current DESCRIPTION "The time at which the Configuration Revision Number was (last) increased to its current value, as indicated in the most recently received VTP advertisement for this management domain. The value 0x0000010100000000 indicates that the device which last increased the Configuration Revision Number had no idea of the date/time, or that no advertisement has been received." ::= { managementDomainEntry 6 } managementDomainRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "The status of this conceptual row." ::= { managementDomainEntry 7 } managementDomainTftpServer OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-create STATUS current DESCRIPTION "The IP address of a TFTP Server in/from which VTP VLAN information for this management domain is to be stored/retrieved. If the information is being locally stored in NVRAM, this object should take the value 0.0.0.0." ::= { managementDomainEntry 8 } managementDomainTftpPathname OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-create STATUS current DESCRIPTION "The complete pathname of the file at the TFTP Server identified by the value of managementDomainTftpServer in/from which VTP VLAN information for this management domain is to be stored/retrieved. If the value of corresponding instance of managementDomainTftpServer is 0.0.0.0, the value of this object is ignored." ::= { managementDomainEntry 9 } managementDomainPruningState OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-create STATUS current DESCRIPTION "An indication of whether VTP pruning is enabled or disabled in this managament domain. This value can only be modified by local/network management when the value of the corresponding instance of managementDomainLocalMode is 'server'." ::= { managementDomainEntry 10 } managementDomainVersionInUse OBJECT-TYPE SYNTAX INTEGER { version1 (1), version2 (2) } MAX-ACCESS read-create STATUS current DESCRIPTION "The current version of the VTP that is in use by the designated management domain. This value can only be modified by local/network managment when the value of the corresponding instance of managementDomainLocalMode is 'server'." ::= { managementDomainEntry 11 } -- -- VLAN information -- vlanInfo OBJECT IDENTIFIER ::= { vtpMIBObjects 3 } -- Global information on current VLANs -- -- This information is maintained by VTP Clients and VTP Servers vtpVlanTable OBJECT-TYPE SYNTAX SEQUENCE OF VtpVlanEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains information on the VLANs which currently exist. The creation, deletion or modification of entries occurs through: a) the receipt of VTP messages in VTP Clients and in VTP Servers, or, b) in VTP Servers (or in VTP transparent mode), through management operations acting upon entries in the vtpVlanEditTable and then issuing an 'apply' command via the vtpVlanEditOperation object." ::= { vlanInfo 1 } vtpVlanEntry OBJECT-TYPE SYNTAX VtpVlanEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Information about one current VLAN. The managementDomainIndex value in the INDEX clause indicates which management domain the VLAN is in." INDEX { managementDomainIndex, vtpVlanIndex } ::= { vtpVlanTable 1 } VtpVlanEntry ::= SEQUENCE { vtpVlanIndex VlanIndex, vtpVlanState INTEGER, vtpVlanType VlanType, vtpVlanName DisplayString, vtpVlanMtu INTEGER, vtpVlanDot10Said OCTET STRING, vtpVlanRingNumber INTEGER, vtpVlanBridgeNumber INTEGER, vtpVlanStpType INTEGER, vtpVlanParentVlan VlanIndex, vtpVlanTranslationalVlan1 VlanIndex, vtpVlanTranslationalVlan2 VlanIndex, vtpVlanBridgeType INTEGER, vtpVlanAreHopCount INTEGER, vtpVlanSteHopCount INTEGER, vtpVlanIsCRFBackup TruthValue, vtpVlanTypeExt VlanTypeExt } vtpVlanIndex OBJECT-TYPE SYNTAX VlanIndex MAX-ACCESS not-accessible STATUS current DESCRIPTION "The VLAN-id of this VLAN on ISL trunks." ::= { vtpVlanEntry 1 } vtpVlanState OBJECT-TYPE SYNTAX INTEGER { operational(1), suspended(2), mtuTooBigForDevice(3), mtuTooBigForTrunk(4) } MAX-ACCESS read-only STATUS current DESCRIPTION "The state of this VLAN. The state 'mtuTooBigForDevice' indicates that this device cannot participate in this VLAN because the VLAN's MTU is larger than the device can support. The state 'mtuTooBigForTrunk' indicates that while this VLAN's MTU is supported by this device, it is too large for one or more of the device's trunk ports." ::= { vtpVlanEntry 2 } vtpVlanType OBJECT-TYPE SYNTAX VlanType MAX-ACCESS read-only STATUS current DESCRIPTION "The type of this VLAN." ::= { vtpVlanEntry 3 } vtpVlanName OBJECT-TYPE SYNTAX DisplayString (SIZE (1..32)) MAX-ACCESS read-only STATUS current DESCRIPTION "The name of this VLAN. This name is used as the ELAN-name for an ATM LAN-Emulation segment of this VLAN." ::= { vtpVlanEntry 4 } vtpVlanMtu OBJECT-TYPE SYNTAX INTEGER (1500..18190) MAX-ACCESS read-only STATUS current DESCRIPTION "The MTU size on this VLAN, defined as the size of largest MAC-layer (information field portion of the) data frame which can be transmitted on the VLAN." ::= { vtpVlanEntry 5 } vtpVlanDot10Said OBJECT-TYPE SYNTAX OCTET STRING (SIZE (4)) MAX-ACCESS read-only STATUS current DESCRIPTION "The value of the 802.10 SAID field for this VLAN." ::= { vtpVlanEntry 6 } vtpVlanRingNumber OBJECT-TYPE SYNTAX INTEGER (0..4095) MAX-ACCESS read-only STATUS current DESCRIPTION "The ring number of this VLAN. This object is only instantiated when the value of the corresponding instance of vtpVlanType has a value of 'fddi' or 'tokenRing' and Source Routing (SRB) is configured for use on this VLAN." ::= { vtpVlanEntry 7 } vtpVlanBridgeNumber OBJECT-TYPE SYNTAX INTEGER (0..15) MAX-ACCESS read-only STATUS current DESCRIPTION "The bridge number of the VTP-capable switches for this VLAN. This object is only instantiated for VLANs that are involved with emulating token ring segments." ::= { vtpVlanEntry 8 } vtpVlanStpType OBJECT-TYPE SYNTAX INTEGER { ieee(1), ibm(2), hybrid(3) } MAX-ACCESS read-only STATUS current DESCRIPTION " The type of the Spanning Tree Protocol (STP) running on this VLAN. This object is only instanciated when the value of the corresponding instance of vtpVlanType has a value of 'fddiNet' or 'trNet'. The value returned by this object depends upon the value of the corresponding instance of vtpVlanEditStpType. - 'ieee' indicates IEEE STP is running exclusively. - 'ibm' indicates IBM STP is running exclusively. - 'hybrid' indicates a STP that allows a combination of IEEE and IBM is running. The 'hybrid' STP type results from tokenRing/fddi VLANs that are children of this trNet/fddiNet parent VLAN being configured in a combination of SRT and SRB vtpVlanBridgeTypes while the instance of vtpVlanEditStpType that corresponds to this object is set to 'auto'." ::= { vtpVlanEntry 9 } vtpVlanParentVlan OBJECT-TYPE SYNTAX VlanIndex MAX-ACCESS read-only STATUS current DESCRIPTION "The parent VLAN for this VLAN. This object is only instantiated when the value of the corresponding instance of vtpVlanType has a value of 'fddi' or 'tokenRing' and Source Routing (SRB) is configured for use on this VLAN. The parent VLAN must have a vtpVlanType value of fddiNet(4) or trNet(5), respectively." ::= { vtpVlanEntry 10 } vtpVlanTranslationalVlan1 OBJECT-TYPE SYNTAX VlanIndex MAX-ACCESS read-only STATUS current DESCRIPTION "A VLAN to which this VLAN is being translational-bridged. If this value and the corresponding instance of vtpVlanTranslationalVlan2 are both zero, then this VLAN is not being translational-bridged." ::= { vtpVlanEntry 11 } vtpVlanTranslationalVlan2 OBJECT-TYPE SYNTAX VlanIndex MAX-ACCESS read-only STATUS current DESCRIPTION "Another VLAN, i.e., other than that indicated by vtpVlanTranslationalVlan1, to which this VLAN is being translational-bridged. If this value and the corresponding instance of vtpVlanTranslationalVlan1 are both zero, then this VLAN is not being translational-bridged." ::= { vtpVlanEntry 12 } vtpVlanBridgeType OBJECT-TYPE SYNTAX INTEGER { srt(1), srb(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "The type of the bridging mode in use on this VLAN. This object is only instantiated when the value of the corresponding instance of vtpVlanType has a value of fddi(2) or tokenRing(3)." ::= { vtpVlanEntry 13 } vtpVlanAreHopCount OBJECT-TYPE SYNTAX INTEGER (1..13) MAX-ACCESS read-only STATUS current DESCRIPTION "The maximum number of bridge hops allowed in All Routes Explorer frames on this VLAN. This object is only instantiated when the value of the corresponding instance of vtpVlanType has a value of fddi(2) or tokenRing(3)." ::= { vtpVlanEntry 14 } vtpVlanSteHopCount OBJECT-TYPE SYNTAX INTEGER (1..13) MAX-ACCESS read-only STATUS current DESCRIPTION "The maximum number of bridge hops allowed in Spanning Tree Explorer frames on this VLAN. This object is only instantiated when the value of the corresponding instance of vtpVlanType has a value of fddi(2) or tokenRing(3)." ::= { vtpVlanEntry 15 } vtpVlanIsCRFBackup OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION " True if this VLAN is of type trCrf and also is acting as a backup trCrf for the ISL distributed BRF" ::= { vtpVlanEntry 16 } vtpVlanTypeExt OBJECT-TYPE SYNTAX VlanTypeExt MAX-ACCESS read-only STATUS current DESCRIPTION "The additional type information of this VLAN." ::= { vtpVlanEntry 17 } -- Modification of Global VLAN Information -- -- To change the global information on current VLANs, including -- creating, modifying or deleting them, -- . the current VLAN information is copied to the "Edit buffer", -- . the information in the Edit buffer is modified as appropriate, -- . an 'apply' is invoked to attempt to instanciate the modified -- contents of the Edit Buffer as the new global VLAN information. -- -- Only one manager can edit the Edit Buffer at a time. So, a -- request to copy the current VLAN information into the Edit Buffer -- must fail if the Edit Buffer is already in use (i.e., is not empty). -- Thus, concurrent attempts by multiple managers to gain use of the -- Edit Buffer are resolved according to whichever of them succeeds -- in performing a successful copy. An OwnerString object provides -- information on which manager currently has access. -- -- Ownership of the Edit Buffer terminates when a NMS explicitly -- releases it, or when a deadman-timer expires. The deadman-timer -- has a fixed expiry interval of 5 minutes. The deadman-timer is -- automatically started on a successful copy operation. The -- restartTimer operation allows an NMS to restart the deadman-timer -- if it wishes to retain ownership of the Edit Buffer for longer -- than 5 minutes. The deadman-timer ceases when the apply operation -- is invoked, and is restarted when the apply operation terminates. -- Restarting the deadman-timer after termination of the apply -- operation allows the results of the apply operation to be retained -- until the requesting manager has retrieved them, but for only a -- limited amount of time. vlanEdit OBJECT IDENTIFIER ::= { vtpMIBObjects 4 } vtpEditControlTable OBJECT-TYPE SYNTAX SEQUENCE OF VtpEditControlEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table provides the means to control the editing of the VLANs for a particular management domain. Each and every entry in this table augments its corresponding entry in the managementDomainTable; thus, an entry in this table is created/deleted only as a by-product of creating/deleting an entry in the managementDomainTable." ::= { vlanEdit 1 } vtpEditControlEntry OBJECT-TYPE SYNTAX VtpEditControlEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Control information for editing the VLANs in one management domain." AUGMENTS { managementDomainEntry } ::= { vtpEditControlTable 1 } VtpEditControlEntry ::= SEQUENCE { vtpVlanEditOperation INTEGER, vtpVlanApplyStatus INTEGER, vtpVlanEditBufferOwner OwnerString, vtpVlanEditConfigRevNumber Gauge32 } vtpVlanEditOperation OBJECT-TYPE SYNTAX INTEGER { none(1), copy(2), apply(3), release(4), restartTimer(5) } MAX-ACCESS read-create STATUS current DESCRIPTION "This object always has the value 'none' when read. When written, each value causes the appropriate action: 'copy' - causes the creation of rows in the vtpVlanEditTable exactly corresponding to the current global VLAN information for this management domain. If the Edit Buffer (for this management domain) is not currently empty, a copy operation fails. A successful copy operation starts the deadman-timer. 'apply' - first performs a consistent check on the the modified information contained in the Edit Buffer, and if consistent, then tries to instanciate the modified information as the new global VLAN information. Note that an empty Edit Buffer (for the management domain) would always result in an inconsistency since the default VLANs are required to be present. 'release' - flushes the Edit Buffer (for this management domain), clears the Owner information, and aborts the deadman-timer. A release is generated automatically if the deadman-timer ever expires. 'restartTimer' - restarts the deadman-timer. 'none' - no operation is performed." ::= { vtpEditControlEntry 1 } vtpVlanApplyStatus OBJECT-TYPE SYNTAX INTEGER { inProgress(1), succeeded(2), configNumberError(3), inconsistentEdit(4), tooBig(5), localNVStoreFail(6), remoteNVStoreFail(7), editBufferEmpty(8), someOtherError(9) } MAX-ACCESS read-only STATUS current DESCRIPTION "The current status of an 'apply' operation to instanciate the Edit Buffer as the new global VLAN information (for this management domain). If no apply is currently active, the status represented is that of the most recently completed apply. The possible values are: inProgress - 'apply' operation in progress; succeeded - the 'apply' was successful (this value is also used when no apply has been invoked since the last time the local system restarted); configNumberError - the apply failed because the value of vtpVlanEditConfigRevNumber was less or equal to the value of current value of vtpConfigRevNumber; inconsistentEdit - the apply failed because the modified information was not self-consistent; tooBig - the apply failed because the modified information was too large to fit in this VTP Server's non-volatile storage location; localNVStoreFail - the apply failed in trying to store the new information in a local non-volatile storage location; remoteNVStoreFail - the apply failed in trying to store the new information in a remote non-volatile storage location; editBufferEmpty - the apply failed because the Edit Buffer was empty (for this management domain). someOtherError - the apply failed for some other reason (e.g., insufficient memory)." ::= { vtpEditControlEntry 2 } vtpVlanEditBufferOwner OBJECT-TYPE SYNTAX OwnerString MAX-ACCESS read-create STATUS current DESCRIPTION "The management station which is currently using the Edit Buffer for this management domain. When the Edit Buffer for a management domain is not currently in use, the value of this object is the zero-length string. Note that it is also the zero-length string if a manager fails to set this object when invoking a copy operation." ::= { vtpEditControlEntry 3 } vtpVlanEditConfigRevNumber OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-create STATUS current DESCRIPTION "The Configuration Revision Number to be used for the next apply operation. This value is initialized (by the agent) on a copy operation to be one greater than the value of vtpConfigRevNumber. On an apply, if the number is less or equal to the value of vtpConfigRevNumber, then the apply fails. The value can be modified (increased) by network management before an apply to ensure than an apply does not fail for this reason. This object is used to allow management control over whether a configuration revision received via a VTP advertisement after a copy operation but before the succeeding apply operation is lost by being overwritten by the (local) edit operation. By default, the apply operation will fail in this situation. By increasing this object's value after the copy but before the apply, management can control whether the apply is to succeed (with the update via VTP advertisement being lost)." ::= { vtpEditControlEntry 4 } vtpVlanEditTable OBJECT-TYPE SYNTAX SEQUENCE OF VtpVlanEditEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table which contains the information in the Edit Buffers, one Edit Buffer per management domain. The information for a particular management domain is initialized, by a 'copy' operation, to be the current global VLAN information for that management domain. After initialization, editing can be performed to add VLANs, delete VLANs, or modify their global parameters. The information as modified through editing is local to this Edit Buffer. An apply operation using the vtpVlanEditOperation object is necessary to instanciate the modified information as the new global VLAN information for that management domain. To use the Edit Buffer, a manager acts as follows: 1. ensures the Edit Buffer for a management domain is empty, i.e., there are no rows in this table for this management domain. 2. issues a SNMP set operation which sets vtpVlanEditOperation to 'copy', and vtpVlanEditBufferOwner to its own identifier (e.g., its own IP address). 3. if this set operation is successful, proceeds to edit the information in the vtpVlanEditTable. 4. if and when the edited information is to be instantiated, issues a SNMP set operation which sets vtpVlanEditOperation to 'apply'. 5. issues retrieval requests to obtain the value of vtpVlanApplyStatus, until the result of the apply is determined. 6. releases the Edit Buffer by issuing a SNMP set operation which sets vtpVlanEditOperation to 'release'. Note that the information contained in this table is not saved across agent reboots." ::= { vlanEdit 2 } vtpVlanEditEntry OBJECT-TYPE SYNTAX VtpVlanEditEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Information about one VLAN in the Edit Buffer for a particular management domain." INDEX { managementDomainIndex, vtpVlanEditIndex } ::= { vtpVlanEditTable 1 } VtpVlanEditEntry ::= SEQUENCE { vtpVlanEditIndex VlanIndex, vtpVlanEditState INTEGER, vtpVlanEditType VlanType, vtpVlanEditName DisplayString, vtpVlanEditMtu INTEGER, vtpVlanEditDot10Said OCTET STRING, vtpVlanEditRingNumber INTEGER, vtpVlanEditBridgeNumber INTEGER, vtpVlanEditStpType INTEGER, vtpVlanEditParentVlan VlanIndex, vtpVlanEditRowStatus RowStatus, vtpVlanEditTranslationalVlan1 VlanIndex, vtpVlanEditTranslationalVlan2 VlanIndex, vtpVlanEditBridgeType INTEGER, vtpVlanEditAreHopCount INTEGER, vtpVlanEditSteHopCount INTEGER, vtpVlanEditIsCRFBackup TruthValue, vtpVlanEditTypeExt VlanTypeExt } vtpVlanEditIndex OBJECT-TYPE SYNTAX VlanIndex MAX-ACCESS not-accessible STATUS current DESCRIPTION "The VLAN-id which this VLAN would have on ISL trunks." ::= { vtpVlanEditEntry 1 } vtpVlanEditState OBJECT-TYPE SYNTAX INTEGER { operational(1), suspended(2) } MAX-ACCESS read-create STATUS current DESCRIPTION "The state which this VLAN would have." DEFVAL { operational } ::= { vtpVlanEditEntry 2 } vtpVlanEditType OBJECT-TYPE SYNTAX VlanType MAX-ACCESS read-create STATUS current DESCRIPTION "The type which this VLAN would have. An implementation may restrict access to this object." DEFVAL { ethernet } ::= { vtpVlanEditEntry 3 } vtpVlanEditName OBJECT-TYPE SYNTAX DisplayString (SIZE (1..32)) MAX-ACCESS read-create STATUS current DESCRIPTION "The name which this VLAN would have. This name would be used as the ELAN-name for an ATM LAN-Emulation segment of this VLAN. An implementation may restrict access to this object." ::= { vtpVlanEditEntry 4 } vtpVlanEditMtu OBJECT-TYPE SYNTAX INTEGER (1500..18190) MAX-ACCESS read-create STATUS current DESCRIPTION "The MTU size which this VLAN would have, defined as the size of largest MAC-layer (information field portion of the) data frame which can be transmitted on the VLAN. An implementation may restrict access to this object." DEFVAL { 1500 } ::= { vtpVlanEditEntry 5 } vtpVlanEditDot10Said OBJECT-TYPE SYNTAX OCTET STRING (SIZE (4)) MAX-ACCESS read-create STATUS current DESCRIPTION "The value of the 802.10 SAID field which would be used for this VLAN. An implementation may restrict access to this object." ::= { vtpVlanEditEntry 6 } vtpVlanEditRingNumber OBJECT-TYPE SYNTAX INTEGER (0..4095) MAX-ACCESS read-create STATUS current DESCRIPTION "The ring number which would be used for this VLAN. This object is only instantiated when the value of the corresponding instance of vtpVlanEditType has a value of 'fddi' or 'tokenRing' and Source Routing (SRB) is configured for use on this VLAN." ::= { vtpVlanEditEntry 7 } vtpVlanEditBridgeNumber OBJECT-TYPE SYNTAX INTEGER (0..15) MAX-ACCESS read-create STATUS current DESCRIPTION "The bridge number of the VTP-capable switches which would be used for this VLAN. This object is only instantiated when the value of the corresponding instance of vtpVlanEditType has a value of fddiNet(4) or trNet(5)." ::= { vtpVlanEditEntry 8 } vtpVlanEditStpType OBJECT-TYPE SYNTAX INTEGER { ieee(1), ibm(2), auto(3) } MAX-ACCESS read-create STATUS current DESCRIPTION "The type of the Spanning Tree Protocol which would be running on this VLAN. This object is only instantiated when the value of the corresponding instance of vtpVlanEditType has a value of fddiNet(4) or trNet(5). If 'ieee' is selected, the STP that runs will be IEEE. If 'ibm' is selected, the STP that runs will be IBM. If 'auto' is selected, the STP that runs will be dependant on the values of vtpVlanEditBridgeType for all children tokenRing/fddi type VLANs. This will result in a 'hybrid' STP (see vtpVlanStpType)." ::= { vtpVlanEditEntry 9 } vtpVlanEditParentVlan OBJECT-TYPE SYNTAX VlanIndex MAX-ACCESS read-create STATUS current DESCRIPTION "The VLAN index of the VLAN which would be the parent for this VLAN. This object is only instantiated when the value of the corresponding instance of vtpVlanEditType has a value of 'fddi' or 'tokenRing' and Source Routing (SRB) is configured for use on this VLAN. The parent VLAN must have a vtpVlanEditType value of fddiNet(4) or trNet(5), respectively." ::= { vtpVlanEditEntry 10 } vtpVlanEditRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "The status of this row. Any and all columnar objects in an existing row can be modified irrespective of the status of the row. A row is not qualified for activation until instances of at least its vtpVlanEditType, vtpVlanEditName and vtpVlanEditDot10Said columns have appropriate values. The management station should endeavor to make all rows consistent in the table before 'apply'ing the buffer. An inconsistent entry in the table will cause the entire buffer to be rejected with the vtpVlanApplyStatus object set to the appropriate error value." ::= { vtpVlanEditEntry 11 } vtpVlanEditTranslationalVlan1 OBJECT-TYPE SYNTAX VlanIndex MAX-ACCESS read-create STATUS current DESCRIPTION "A VLAN to which this VLAN would be translational-bridged. If this value and the corresponding instance of vtpVlanTranslationalVlan2 are both zero, then this VLAN would not be translational-bridged. An implementation may restrict access to this object." DEFVAL { 0 } ::= { vtpVlanEditEntry 12 } vtpVlanEditTranslationalVlan2 OBJECT-TYPE SYNTAX VlanIndex MAX-ACCESS read-create STATUS current DESCRIPTION "Another VLAN, i.e., other than that indicated by vtpVlanEditTranslationalVlan1, to which this VLAN would be translational-bridged. If this value and the corresponding instance of vtpVlanTranslationalVlan1 are both zero, then this VLAN would not be translational-bridged. An implementation may restrict access to this object." DEFVAL { 0 } ::= { vtpVlanEditEntry 13 } vtpVlanEditBridgeType OBJECT-TYPE SYNTAX INTEGER { srt(1), srb(2) } MAX-ACCESS read-create STATUS current DESCRIPTION "The type of bridging mode which would be in use on this VLAN. This object is only instantiated when the value of the corresponding instance of vtpVlanEditType has a value of fddi(2) or tokenRing(3)." ::= { vtpVlanEditEntry 14 } vtpVlanEditAreHopCount OBJECT-TYPE SYNTAX INTEGER (1..13) MAX-ACCESS read-create STATUS current DESCRIPTION "The maximum number of bridge hops allowed in All Routes Explorer frames on this VLAN. This object is only instantiated when the value of the corresponding instance of vtpVlanType has a value of fddi(2) or tokenRing(3)." ::= { vtpVlanEditEntry 15 } vtpVlanEditSteHopCount OBJECT-TYPE SYNTAX INTEGER (1..13) MAX-ACCESS read-create STATUS current DESCRIPTION "The maximum number of bridge hops allowed in Spanning Tree Explorer frames on this VLAN. This object is only instantiated when the value of the corresponding instance of vtpVlanType has a value of fddi(2) or tokenRing(3)." ::= { vtpVlanEditEntry 16} vtpVlanEditIsCRFBackup OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-create STATUS current DESCRIPTION " True if this VLAN is of type trCrf and also is acting as a backup trCrf for the ISL distributed BRF. This object is only instantiated when the value of the corresponding instance of vtpVlanEditType has a value of tokenRing(3)." ::= { vtpVlanEditEntry 17 } vtpVlanEditTypeExt OBJECT-TYPE SYNTAX VlanTypeExt MAX-ACCESS read-only STATUS current DESCRIPTION "The additional type information of this VLAN." ::= { vtpVlanEditEntry 18 } -- -- VTP Statistics -- vtpStats OBJECT IDENTIFIER ::= { vtpMIBObjects 5 } vtpStatsTable OBJECT-TYPE SYNTAX SEQUENCE OF VtpStatsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table of VTP statistics." ::= { vtpStats 1 } vtpStatsEntry OBJECT-TYPE SYNTAX VtpStatsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "VTP statistics for one management domain." AUGMENTS { managementDomainEntry } ::= { vtpStatsTable 1 } VtpStatsEntry ::= SEQUENCE { vtpInSummaryAdverts Counter32, vtpInSubsetAdverts Counter32, vtpInAdvertRequests Counter32, vtpOutSummaryAdverts Counter32, vtpOutSubsetAdverts Counter32, vtpOutAdvertRequests Counter32, vtpConfigRevNumberErrors Counter32, vtpConfigDigestErrors Counter32 } vtpInSummaryAdverts OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of VTP Summary Adverts received for this management domain." ::= { vtpStatsEntry 1 } vtpInSubsetAdverts OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of VTP Subset Adverts received for this management domain." ::= { vtpStatsEntry 2 } vtpInAdvertRequests OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of VTP Advert Requests received for this management domain." ::= { vtpStatsEntry 3 } vtpOutSummaryAdverts OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of VTP Summary Adverts sent for this management domain." ::= { vtpStatsEntry 4 } vtpOutSubsetAdverts OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of VTP Subset Adverts sent for this management domain." ::= { vtpStatsEntry 5 } vtpOutAdvertRequests OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of VTP Advert Requests sent for this management domain." ::= { vtpStatsEntry 6 } vtpConfigRevNumberErrors OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of occurrences of configuration revision number errors for this management domain. A configuration revision number error occurs when a device receives a VTP advertisement for which: - the advertisement's Configuration Revision Number is the same as the current locally-held value, and - the advertisement's digest value is different from the current locally-held value." ::= { vtpStatsEntry 7 } vtpConfigDigestErrors OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of occurrences of configuration digest errors for this management domain. A configuration digest error occurs when a device receives a VTP advertisement for which: - the advertisement's Configuration Revision Number is greater than the current locally-held value, and - the advertisement's digest value does not match the VLAN information assumed by the receiver of the advertisement, where the infomation assumed is the combination of the information explicitly contained in the advertisement plus any omitted information as currently known by the receiving device." ::= { vtpStatsEntry 8 } -- Trunk Ports vlanTrunkPorts OBJECT IDENTIFIER ::= { vtpMIBObjects 6 } vlanTrunkPortTable OBJECT-TYPE SYNTAX SEQUENCE OF VlanTrunkPortEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table containing information on the local system's VLAN trunk ports." ::= { vlanTrunkPorts 1 } vlanTrunkPortEntry OBJECT-TYPE SYNTAX VlanTrunkPortEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Information about one trunk port." INDEX { vlanTrunkPortIfIndex } ::= { vlanTrunkPortTable 1 } VlanTrunkPortEntry ::= SEQUENCE { vlanTrunkPortIfIndex InterfaceIndex, vlanTrunkPortManagementDomain ManagementDomainIndex, vlanTrunkPortEncapsulationType INTEGER, vlanTrunkPortVlansEnabled OCTET STRING, vlanTrunkPortNativeVlan VlanIndex, vlanTrunkPortRowStatus RowStatus, vlanTrunkPortInJoins Counter32, vlanTrunkPortOutJoins Counter32, vlanTrunkPortOldAdverts Counter32, vlanTrunkPortVlansPruningEligible OCTET STRING, vlanTrunkPortVlansXmitJoined OCTET STRING, vlanTrunkPortVlansRcvJoined OCTET STRING, vlanTrunkPortDynamicState INTEGER, vlanTrunkPortDynamicStatus INTEGER, vlanTrunkPortVtpEnabled TruthValue, vlanTrunkPortEncapsulationOperType INTEGER, vlanTrunkPortVlansEnabled2k OCTET STRING, vlanTrunkPortVlansEnabled3k OCTET STRING, vlanTrunkPortVlansEnabled4k OCTET STRING, vtpVlansPruningEligible2k OCTET STRING, vtpVlansPruningEligible3k OCTET STRING, vtpVlansPruningEligible4k OCTET STRING, vlanTrunkPortVlansXmitJoined2k OCTET STRING, vlanTrunkPortVlansXmitJoined3k OCTET STRING, vlanTrunkPortVlansXmitJoined4k OCTET STRING, vlanTrunkPortVlansRcvJoined2k OCTET STRING, vlanTrunkPortVlansRcvJoined3k OCTET STRING, vlanTrunkPortVlansRcvJoined4k OCTET STRING, vlanTrunkPortDot1qTunnel INTEGER } vlanTrunkPortIfIndex OBJECT-TYPE SYNTAX InterfaceIndex MAX-ACCESS not-accessible STATUS current DESCRIPTION "The value of ifIndex for the interface corresponding to this trunk port." ::= { vlanTrunkPortEntry 1 } vlanTrunkPortManagementDomain OBJECT-TYPE SYNTAX ManagementDomainIndex MAX-ACCESS read-create STATUS current DESCRIPTION "The value of managementDomainIndex for the management domain on this trunk port. Devices which support only one management domain will support this object read-only." ::= { vlanTrunkPortEntry 2 } vlanTrunkPortEncapsulationType OBJECT-TYPE SYNTAX INTEGER { isl(1), dot10(2), lane(3), dot1Q(4), negotiate(5) } MAX-ACCESS read-create STATUS current DESCRIPTION "The type of VLAN encapsulation desired to be used on this trunk port. It is either a particular type, or 'negotiate' meaning whatever type results from the negotiation. negotiate(5) is not allowed if the port does not support negotiation or if its vlanTrunkPortDynamicState is set to on(1) or onNoNegotiate(5). Whether writing to this object in order to modify the encapsulation is supported is both device and interface specific." ::= { vlanTrunkPortEntry 3 } vlanTrunkPortVlansEnabled OBJECT-TYPE SYNTAX OCTET STRING (SIZE (128)) MAX-ACCESS read-create STATUS current DESCRIPTION "A string of octets containing one bit per VLAN in the management domain on this trunk port. The first octet corresponds to VLANs with VlanIndex values of 0 through 7; the second octet to VLANs 8 through 15; etc. The most significant bit of each octet corresponds to the lowest value VlanIndex in that octet. If the bit corresponding to a VLAN is set to '1', then the local system is enabled for sending and receiving frames on that VLAN; if the bit is set to '0', then the system is disabled from sending and receiving frames on that VLAN. To avoid conflicts between overlapping partial updates by multiple managers, i.e., updates which modify only a portion of an instance of this object (e.g., enable/disable a single VLAN on the trunk port), any SNMP Set operation accessing an instance of this object should also write the value of vlanTrunkPortSetSerialNo." ::= { vlanTrunkPortEntry 4 } vlanTrunkPortNativeVlan OBJECT-TYPE SYNTAX VlanIndex MAX-ACCESS read-create STATUS current DESCRIPTION "The VlanIndex of the VLAN which is represented by native frames on this trunk port. For trunk ports not supporting the sending and receiving of native frames, this value should be set to zero." ::= { vlanTrunkPortEntry 5 } vlanTrunkPortRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "The status of this row. In some circumstances, the creation of a row in this table is needed to enable the appropriate trunking/tagging protocol on the port, to enable the use of VTP on the port, and to assign the port to the appropriate management domain. In other circumstances, rows in this table will be created as a by-product of other operations." ::= { vlanTrunkPortEntry 6 } vlanTrunkPortInJoins OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of VTP Join messages received on this trunk port." ::= { vlanTrunkPortEntry 7 } vlanTrunkPortOutJoins OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of VTP Join messages sent on this trunk port." ::= { vlanTrunkPortEntry 8 } vlanTrunkPortOldAdverts OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of VTP Advertisement messages which indicated the sender does not support VLAN-pruning received on this trunk port." ::= { vlanTrunkPortEntry 9 } vlanTrunkPortVlansPruningEligible OBJECT-TYPE SYNTAX OCTET STRING (SIZE (128)) MAX-ACCESS read-create STATUS current DESCRIPTION "A string of octets containing one bit per VLAN in the management domain on this trunk port. The first octet corresponds to VLANs with VlanIndex values of 0 through 7; the second octet to VLANs 8 through 15; etc. The most significant bit of each octet corresponds to the lowest value VlanIndex in that octet. If the bit corresponding to a VLAN is set to '1', then the local system is permitted to prune that VLAN on this trunk port; if the bit is set to '0', then the system must not prune that VLAN on this trunk port. To avoid conflicts between overlapping partial updates by multiple managers, i.e., updates which modify only a portion of an instance of this object (e.g., enable/disable a single VLAN on the trunk port), any SNMP Set operation accessing an instance of this object should also write the value of vlanTrunkPortSetSerialNo." ::= { vlanTrunkPortEntry 10 } vlanTrunkPortVlansXmitJoined OBJECT-TYPE SYNTAX OCTET STRING (SIZE (128)) MAX-ACCESS read-only STATUS current DESCRIPTION "A string of octets containing one bit per VLAN in the management domain on this trunk port. The first octet corresponds to VLANs with VlanIndex values of 0 through 7; the second octet to VLANs 8 through 15; etc. The most significant bit of each octet corresponds to the lowest value VlanIndex in that octet. If the bit corresponding to a VLAN is set to '1', then this VLAN is presently being forwarded on this trunk port, i.e., it is not pruned; if the bit is set to '0', then this VLAN is presently not being forwarded on this trunk port, either because it is pruned or for some other reason." ::= { vlanTrunkPortEntry 11 } vlanTrunkPortVlansRcvJoined OBJECT-TYPE SYNTAX OCTET STRING (SIZE (128)) MAX-ACCESS read-only STATUS current DESCRIPTION "A string of octets containing one bit per VLAN in the management domain on this trunk port. The first octet corresponds to VLANs with VlanIndex values of 0 through 7; the second octet to VLANs 8 through 15; etc. The most significant bit of each octet corresponds to the lowest value VlanIndex in that octet. If the bit corresponding to a VLAN is set to '1', then the local switch is currently sending joins for this VLAN on this trunk port, i.e., it is asking to receive frames for this VLAN; if the bit is set to '0', then the local switch is not currently sending joins for this VLAN on this trunk port." ::= { vlanTrunkPortEntry 12 } vlanTrunkPortDynamicState OBJECT-TYPE SYNTAX INTEGER { on(1), off(2), desirable(3), auto(4), onNoNegotiate(5) } MAX-ACCESS read-create STATUS current DESCRIPTION "For devices that allows dynamic determination of whether a link between two switches should be a trunk or not, this object allows the operator to mandate the behavior of that dynamic mechanism. on(1) dictates that the interface will always be a trunk. This is the value for static entries (those that show no dynamic behavior). If the negotiation is supported on this port, negotiation will take place with the far end to attempt to bring the far end into trunking state. off(2) allows an operator to specify that the specified interface is never to be trunk, regardless of any dynamic mechanisms to the contrary. This value is useful for overriding the default behavior of some switches. If the negotiation is supported on this port, negotiation will take place with the far end to attempt on the link to bring the far end into non-trunking state. desirable(3) is used to indicate that it is desirable for the interface to become a trunk. The device will initiate any negotiation necessary to become a trunk but will not become a trunk unless it receives confirmation from the far end on the link. auto(4) is used to indicate that the interface is capable and willing to become a trunk but will not initiate trunking negotiations. The far end on the link are required to either start negotiations or start sending encapsulated packets, on which event the specified interface will become a trunk. onNoNegotiate(5) is used to indicate that the interface is permanently set to be a trunk, and no negotiation takes place with the far end on the link to ensure consistent operation. This is similar to on(1) except no negotiation takes place with the far end. If the port does not support negotiation or its vlanTrunkPortEncapsulationType is set to negotiate(5), onNoNegotiate(5) is not allowed. Devices that do no support dynamic determination (for just a particular interface, encapsulation or for the whole device) need only support the 'on', and 'off' values." ::= { vlanTrunkPortEntry 13 } vlanTrunkPortDynamicStatus OBJECT-TYPE SYNTAX INTEGER { trunking(1), notTrunking(2) } MAX-ACCESS read-only STATUS current DESCRIPTION " Indicates whether the specified interface is either acting as a trunk or not. This is a result of the vlanTrunkPortDynamicState and the ifOperStatus of the trunk port itself." ::= { vlanTrunkPortEntry 14 } vlanTrunkPortVtpEnabled OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-create STATUS current DESCRIPTION " Some trunk interface modules allow VTP to be enabled/disabled seperately from that of the central device. In such a case this object provides management a way to remotely enable VTP on that module. If a module does not support a seperate VTP enabled state then this object shall always return 'true' and will accept no other value during a SET operation." ::= { vlanTrunkPortEntry 15 } vlanTrunkPortEncapsulationOperType OBJECT-TYPE SYNTAX INTEGER { isl(1), dot10(2), lane(3), dot1Q(4), negotiating(5), notApplicable(6) } MAX-ACCESS read-only STATUS current DESCRIPTION "The type of VLAN encapsulation in use on this trunk port. For intefaces with vlanTrunkPortDynamicStatus of notTrunking(2) the vlanTrunkPortEncapsulationOperType shall be notApplicable(6). " ::= { vlanTrunkPortEntry 16 } vlanTrunkPortVlansEnabled2k OBJECT-TYPE SYNTAX OCTET STRING (SIZE (0..128)) MAX-ACCESS read-create STATUS current DESCRIPTION "A string of octets containing one bit per VLAN for VLANS with VlanIndex values of 1024 through 2047 in the management domain on this trunk port. The first octet corresponds to VLANs with VlanIndex values of 1024 through 1031; the second octet to VLANs 1032 through 1039; etc. The most significant bit of each octet corresponds to the lowest value VlanIndex in that octet. If the bit corresponding to a VLAN is set to '1', then the local system is enabled for sending and receiving frames on that VLAN; if the bit is set to '0', then the system is disabled from sending and receiving frames on that VLAN. The default value is zero length string. To avoid conflicts between overlapping partial updates by multiple managers, i.e., updates which modify only a portion of an instance of this object (e.g., enable/disable a single VLAN on the trunk port), any SNMP Set operation accessing an instance of this object should also write the value of vlanTrunkPortSetSerialNo." ::= { vlanTrunkPortEntry 17 } vlanTrunkPortVlansEnabled3k OBJECT-TYPE SYNTAX OCTET STRING (SIZE (0..128)) MAX-ACCESS read-create STATUS current DESCRIPTION "A string of octets containing one bit per VLAN for VLANS with VlanIndex values of 2048 through 3071 in the management domain on this trunk port. The first octet corresponds to VLANs with VlanIndex values of 2048 through 2055; the second octet to VLANs 2056 through 2063; etc. The most significant bit of each octet corresponds to the lowest value VlanIndex in that octet. If the bit corresponding to a VLAN is set to '1', then the local system is enabled for sending and receiving frames on that VLAN; if the bit is set to '0', then the system is disabled from sending and receiving frames on that VLAN. The default value is zero length string. To avoid conflicts between overlapping partial updates by multiple managers, i.e., updates which modify only a portion of an instance of this object (e.g., enable/disable a single VLAN on the trunk port), any SNMP Set operation accessing an instance of this object should also write the value of vlanTrunkPortSetSerialNo." ::= { vlanTrunkPortEntry 18 } vlanTrunkPortVlansEnabled4k OBJECT-TYPE SYNTAX OCTET STRING (SIZE (0..128)) MAX-ACCESS read-create STATUS current DESCRIPTION "A string of octets containing one bit per VLAN for VLANS with VlanIndex values of 3072 through 4095 in the management domain on this trunk port. The first octet corresponds to VLANs with VlanIndex values of 3072 through 3079; the second octet to VLANs 3080 through 3087; etc. The most significant bit of each octet corresponds to the lowest value VlanIndex in that octet. If the bit corresponding to a VLAN is set to '1', then the local system is enabled for sending and receiving frames on that VLAN; if the bit is set to '0', then the system is disabled from sending and receiving frames on that VLAN. The default value is zero length string. To avoid conflicts between overlapping partial updates by multiple managers, i.e., updates which modify only a portion of an instance of this object (e.g., enable/disable a single VLAN on the trunk port), any SNMP Set operation accessing an instance of this object should also write the value of vlanTrunkPortSetSerialNo." ::= { vlanTrunkPortEntry 19 } vtpVlansPruningEligible2k OBJECT-TYPE SYNTAX OCTET STRING (SIZE (0..128)) MAX-ACCESS read-create STATUS current DESCRIPTION "A string of octets containing one bit per VLAN for VLANS with VlanIndex values of 1024 through 2047 in the management domain on this trunk port. The first octet corresponds to VLANs with VlanIndex values of 1024 through 1031; the second octet to VLANs 1032 through 1039; etc. The most significant bit of each octet corresponds to the lowest value VlanIndex in that octet. If the bit corresponding to a VLAN is set to '1', then the local system is permitted to prune that VLAN on this trunk port; if the bit is set to '0', then the system must not prune that VLAN on this trunk port. The default value is zero length string. To avoid conflicts between overlapping partial updates by multiple managers, i.e., updates which modify only a portion of an instance of this object (e.g., enable/disable a single VLAN on the trunk port), any SNMP Set operation accessing an instance of this object should also write the value of vlanTrunkPortSetSerialNo." ::= { vlanTrunkPortEntry 20 } vtpVlansPruningEligible3k OBJECT-TYPE SYNTAX OCTET STRING (SIZE (0..128)) MAX-ACCESS read-create STATUS current DESCRIPTION "A string of octets containing one bit per VLAN for VLANS with VlanIndex values of 2048 through 3071 in the management domain on this trunk port. The first octet corresponds to VLANs with VlanIndex values of 2048 through 2055; the second octet to VLANs 2056 through 2063; etc. The most significant bit of each octet corresponds to the lowest value VlanIndex in that octet. If the bit corresponding to a VLAN is set to '1', then the local system is permitted to prune that VLAN on this trunk port; if the bit is set to '0', then the system must not prune that VLAN on this trunk port. The default value is zero length string. To avoid conflicts between overlapping partial updates by multiple managers, i.e., updates which modify only a portion of an instance of this object (e.g., enable/disable a single VLAN on the trunk port), any SNMP Set operation accessing an instance of this object should also write the value of vlanTrunkPortSetSerialNo." ::= { vlanTrunkPortEntry 21 } vtpVlansPruningEligible4k OBJECT-TYPE SYNTAX OCTET STRING (SIZE (0..128)) MAX-ACCESS read-create STATUS current DESCRIPTION "A string of octets containing one bit per VLAN for VLANS with VlanIndex values of 3072 through 4095 in the management domain on this trunk port. The first octet corresponds to VLANs with VlanIndex values of 3072 through 3079; the second octet to VLANs 3080 through 3087; etc. The most significant bit of each octet corresponds to the lowest value VlanIndex in that octet. If the bit corresponding to a VLAN is set to '1', then the local system is permitted to prune that VLAN on this trunk port; if the bit is set to '0', then the system must not prune that VLAN on this trunk port. The default value is zero length string. To avoid conflicts between overlapping partial updates by multiple managers, i.e., updates which modify only a portion of an instance of this object (e.g., enable/disable a single VLAN on the trunk port), any SNMP Set operation accessing an instance of this object should also write the value of vlanTrunkPortSetSerialNo." ::= { vlanTrunkPortEntry 22 } vlanTrunkPortVlansXmitJoined2k OBJECT-TYPE SYNTAX OCTET STRING (SIZE (0..128)) MAX-ACCESS read-only STATUS current DESCRIPTION "A string of octets containing one bit per VLAN for VLANS with VlanIndex values of 1024 through 2047 in the management domain on this trunk port. The first octet corresponds to VLANs with VlanIndex values of 1024 through 1031; the second octet to VLANs 1032 through 1039; etc. The most significant bit of each octet corresponds to the lowest value VlanIndex in that octet. If the bit corresponding to a VLAN is set to '1', then this VLAN is presently being forwarded on this trunk port, i.e., it is not pruned; if the bit is set to '0', then this VLAN is presently not being forwarded on this trunk port, either because it is pruned or for some other reason." ::= { vlanTrunkPortEntry 23 } vlanTrunkPortVlansXmitJoined3k OBJECT-TYPE SYNTAX OCTET STRING (SIZE (0..128)) MAX-ACCESS read-only STATUS current DESCRIPTION "A string of octets containing one bit per VLAN for VLANS with VlanIndex values of 2048 through 3071 in the management domain on this trunk port. The first octet corresponds to VLANs with VlanIndex values of 2048 through 2055; the second octet to VLANs 2056 through 2063; etc. The most significant bit of each octet corresponds to the lowest value VlanIndex in that octet. If the bit corresponding to a VLAN is set to '1', then this VLAN is presently being forwarded on this trunk port, i.e., it is not pruned; if the bit is set to '0', then this VLAN is presently not being forwarded on this trunk port, either because it is pruned or for some other reason." ::= { vlanTrunkPortEntry 24 } vlanTrunkPortVlansXmitJoined4k OBJECT-TYPE SYNTAX OCTET STRING (SIZE (0..128)) MAX-ACCESS read-only STATUS current DESCRIPTION "A string of octets containing one bit per VLAN for VLANS with VlanIndex values of 3072 through 4095 in the management domain on this trunk port. The first octet corresponds to VLANs with VlanIndex values of 3072 through 3079; the second octet to VLANs 3080 through 3087; etc. The most significant bit of each octet corresponds to the lowest value VlanIndex in that octet. If the bit corresponding to a VLAN is set to '1', then this VLAN is presently being forwarded on this trunk port, i.e., it is not pruned; if the bit is set to '0', then this VLAN is presently not being forwarded on this trunk port, either because it is pruned or for some other reason." ::= { vlanTrunkPortEntry 25 } vlanTrunkPortVlansRcvJoined2k OBJECT-TYPE SYNTAX OCTET STRING (SIZE (0..128)) MAX-ACCESS read-only STATUS current DESCRIPTION "A string of octets containing one bit per VLAN for VLANS with VlanIndex values of 1024 through 2047 in the management domain on this trunk port. The first octet corresponds to VLANs with VlanIndex values of 1024 through 1031; the second octet to VLANs 1032 through 1039; etc. The most significant bit of each octet corresponds to the lowest value VlanIndex in that octet. If the bit corresponding to a VLAN is set to '1', then the local switch is currently sending joins for this VLAN on this trunk port, i.e., it is asking to receive frames for this VLAN; if the bit is set to '0', then the local switch is not currently sending joins for this VLAN on this trunk port." ::= { vlanTrunkPortEntry 26 } vlanTrunkPortVlansRcvJoined3k OBJECT-TYPE SYNTAX OCTET STRING (SIZE (0..128)) MAX-ACCESS read-only STATUS current DESCRIPTION "A string of octets containing one bit per VLAN for VLANS with VlanIndex values of 2048 through 3071 in the management domain on this trunk port. The first octet corresponds to VLANs with VlanIndex values of 2048 through 2055; the second octet to VLANs 2056 through 2063; etc. The most significant bit of each octet corresponds to the lowest value VlanIndex in that octet. If the bit corresponding to a VLAN is set to '1', then the local switch is currently sending joins for this VLAN on this trunk port, i.e., it is asking to receive frames for this VLAN; if the bit is set to '0', then the local switch is not currently sending joins for this VLAN on this trunk port." ::= { vlanTrunkPortEntry 27 } vlanTrunkPortVlansRcvJoined4k OBJECT-TYPE SYNTAX OCTET STRING (SIZE (0..128)) MAX-ACCESS read-only STATUS current DESCRIPTION "A string of octets containing one bit per VLAN for VLANS with VlanIndex values of 3072 through 4095 in the management domain on this trunk port. The first octet corresponds to VLANs with VlanIndex values of 3072 through 3079; the second octet to VLANs 3080 through 3087; etc. The most significant bit of each octet corresponds to the lowest value VlanIndex in that octet. If the bit corresponding to a VLAN is set to '1', then the local switch is currently sending joins for this VLAN on this trunk port, i.e., it is asking to receive frames for this VLAN; if the bit is set to '0', then the local switch is not currently sending joins for this VLAN on this trunk port." ::= { vlanTrunkPortEntry 28 } vlanTrunkPortDot1qTunnel OBJECT-TYPE SYNTAX INTEGER { trunk(1), access(2), disabled(3) } MAX-ACCESS read-create STATUS current DESCRIPTION "Indicates dot1qtunnel mode of the port. If the portDot1qTunnel is set to 'trunk' mode, the port's vlanTrunkPortDynamicState will be changed to 'onNoNegotiate' and the vlanTrunkPortEncapsulationType will be set to 'dot1Q'. These values cannot be changed unless dot1q tunnel is disabled on this port. If the portDot1qTunnel mode is set to 'access' mode, the port's vlanTrunkPortDynamicState will be set to 'off'.And the value of vlanTrunkPortDynamicState cannot be changed unless dot1q tunnel is disabled on this port. 1Q packets received on this access port will remain. Setting the port to dot1q tunnel 'disabled' mode causes the dot1q tunnel feature to be disabled on this port. This object can't be set to 'trunk' or 'access' mode, when vlanTrunkPortsDot1qTag object is set to 'false'." DEFVAL { disabled } ::= { vlanTrunkPortEntry 29 } vlanTrunkPortSetSerialNo OBJECT-TYPE SYNTAX TestAndIncr MAX-ACCESS read-write STATUS current DESCRIPTION "An advisory lock used to allow several cooperating SNMPv2 managers to coordinate their use of the SNMPv2 set operation acting upon any instance of vlanTrunkPortVlansEnabled." ::= { vlanTrunkPorts 2 } vlanTrunkPortsDot1qTag OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "An indication of whether the tagging on all VLANs including native VLAN for all 802.1q trunks is enabled. If this object has a value of true(1) then all VLANs including native VLAN are tagged. If the value is false(2) then all VLANs excluding native VLAN are tagged." DEFVAL { false } ::= { vlanTrunkPorts 3 } -- VTP notifications vtpNotifications OBJECT IDENTIFIER ::= { ciscoVtpMIB 2 } vtpNotificationsPrefix OBJECT IDENTIFIER ::= { vtpNotifications 0 } vtpNotificationsObjects OBJECT IDENTIFIER ::= { vtpNotifications 1 } vtpConfigRevNumberError NOTIFICATION-TYPE OBJECTS { managementDomainConfigRevNumber } STATUS current DESCRIPTION "A configuration revision number error notification signifies that a device has incremented its vtpConfigRevNumberErrors counter. Generation of this notification is suppressed if the vtpNotificationsEnabled has the value 'false'. The device must throttle the generation of consecutive vtpConfigRevNumberError notifications so that there is at least a five-second gap between notification of this type. When notification are throttled, they are dropped, not queued for sending at a future time. (Note that 'generating' a notification means sending to all configured recipients.)" ::= { vtpNotificationsPrefix 1 } vtpConfigDigestError NOTIFICATION-TYPE OBJECTS { managementDomainConfigRevNumber } STATUS current DESCRIPTION "A configuration digest error notification signifies that a device has incremented its vtpConfigDigestErrors counter. Generation of this notification is suppressed if the vtpNotificationsEnabled has the value 'false'. The device must throttle the generation of consecutive vtpConfigDigestError notifications so that there is at least a five-second gap between notification of this type. When notification are throttled, they are dropped, not queued for sending at a future time. (Note that 'generating' a notification means sending to all configured recipients.)" ::= { vtpNotificationsPrefix 2 } vtpServerDisabled NOTIFICATION-TYPE OBJECTS { managementDomainConfigRevNumber, vtpMaxVlanStorage } STATUS current DESCRIPTION "A VTP Server disabled notification is generated when the local system is no longer able to function as a VTP Server because the number of defined VLANs is greater than vtpMaxVlanStorage. Generation of this notification is suppressed if the vtpNotificationsEnabled has the value 'false'." ::= { vtpNotificationsPrefix 3 } vtpMtuTooBig NOTIFICATION-TYPE OBJECTS { vlanTrunkPortManagementDomain, vtpVlanState } STATUS current DESCRIPTION "A VTP MTU tooBig notification is generated when a VLAN's MTU size is larger than can be supported either: - by one or more of its trunk ports: the included vtpVlanState has the value 'mtuTooBigForTrunk' and the included vlanTrunkPortManagementDomain is for the first (or only) trunk port, or - by the device itself: vtpVlanState has the value 'mtuTooBigForDevice' and any instance of vlanTrunkPortManagementDomain is included. Devices which have no trunk ports do not send vtpMtuTooBig notifications. Generation of this notification is suppressed if the vtpNotificationsEnabled has the value 'false'." ::= { vtpNotificationsPrefix 4 } vtpVlanRingNumberConfigConflict NOTIFICATION-TYPE OBJECTS { vtpVlanIndex, vtpVlanRingNumber, ifIndex, vtpVlanPortLocalSegment } STATUS current DESCRIPTION "A VTP ring number configuration conflict notification is generated if, and only at the time when, a device learns of a conflict between: a) the ring number (vtpVlanPortLocalSegment) being used on a token ring segment attached to the port identified by ifIndex, and b) the VTP-obtained ring number (vtpVlanRingNumber) for the VLAN identified by vtpVlanIndex. When such a conflict occurs, the bridge port is put into an administrative down position until the conflict is resolved through local/network management intervention. This notification is only applicable to VLANs of type 'tokenRing'." ::= { vtpNotificationsPrefix 5 } vtpVersionOneDeviceDetected NOTIFICATION-TYPE OBJECTS { vlanTrunkPortManagementDomain } STATUS current DESCRIPTION "A VTP version one device detected notification is generated by a device when: a) a management domain has been put into version 2 mode (as accessed by managementDomainVersionInUse). b) 15 minutes has passed since a). c) a version 1 PDU is detected on a trunk on the device that is in that management domain which has a lower revision number than the current configuration." ::= { vtpNotificationsPrefix 6 } vlanTrunkPortDynamicStatusChange NOTIFICATION-TYPE OBJECTS {vlanTrunkPortDynamicStatus} STATUS current DESCRIPTION "A vlanTrunkPortDynamicStatusChange notification is generated by a device when the value of vlanTrunkPortDynamicStatus object has been changed." ::= { vtpNotificationsPrefix 7 } vtpVlanPortLocalSegment OBJECT-TYPE SYNTAX INTEGER (0..65535) MAX-ACCESS read-only STATUS current DESCRIPTION "The ring (segment) number in use on a 802.5 ring. For bridges supporting RFC 1525, this value is the same as given by dot1dSrPortLocalSegment for the bridge port attached to that ring. When tokenRing VLANs are in use, each 'trNet' VLAN can/does have a different instance of dot1dSrPortLocalSegment for each physical port. Note that access to the particuler instance of dot1dSrPortLocalSegment requires knowledge of how the agent supports the multiple 'contexts' required to implement RFC 1525 for multiple VLANs; also note that the assignment of ifIndex values may be different in different 'contexts'." ::= { vtpNotificationsObjects 1 } -- Conformance Information vtpMIBConformance OBJECT IDENTIFIER ::= { ciscoVtpMIB 3 } vtpMIBCompliances OBJECT IDENTIFIER ::= { vtpMIBConformance 1 } vtpMIBGroups OBJECT IDENTIFIER ::= { vtpMIBConformance 2 } -- compliance statements vtpMIBCompliance MODULE-COMPLIANCE STATUS deprecated DESCRIPTION "The compliance statement for VTP implementations." MODULE -- this module MANDATORY-GROUPS { vtpBasicGroup, vtpVlanInfoGroup, -- vtpConfigNotificationsGroup, vtpStatsGroup, vtpTrunkPortGroup } OBJECT managementDomainRowStatus SYNTAX INTEGER { active(1)} -- subset of RowStatus MIN-ACCESS read-only DESCRIPTION "Write access is not required, and only one of the six enumerated values for the RowStatus textual convention need be supported, specifically: active(1)." OBJECT vlanTrunkPortRowStatus SYNTAX INTEGER { active(1)} -- subset of RowStatus MIN-ACCESS read-only DESCRIPTION "Write access is not required, and only one of the six enumerated values for the RowStatus textual convention need be supported, specifically: active(1)." OBJECT vlanTrunkPortManagementDomain MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT vlanTrunkPortEncapsulationType MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT vlanTrunkPortNativeVlan MIN-ACCESS read-only DESCRIPTION "Write access is not required." GROUP vtpVlanInfoEditGroup DESCRIPTION "This group must be implemented by VTP Servers. VTP Clients need not implement these objects, and must not allow VLANs to be created, modified, or destroyed using these objects." ::= { vtpMIBCompliances 1 } vtpMIBCompliance2 MODULE-COMPLIANCE STATUS deprecated DESCRIPTION "The compliance statement for VTP implementations." MODULE -- this module MANDATORY-GROUPS { vtpBasicGroup, vtpVlanInfoGroup, -- vtpConfigNotificationsGroup, vtpStatsGroup, vtpTrunkPortGroup } OBJECT managementDomainRowStatus SYNTAX INTEGER { active(1)} -- subset of RowStatus MIN-ACCESS read-only DESCRIPTION "Write access is not required, and only one of the six enumerated values for the RowStatus textual convention need be supported, specifically: active(1)." OBJECT vlanTrunkPortRowStatus SYNTAX INTEGER { active(1)} -- subset of RowStatus MIN-ACCESS read-only DESCRIPTION "Write access is not required, and only one of the six enumerated values for the RowStatus textual convention need be supported, specifically: active(1)." OBJECT vlanTrunkPortManagementDomain MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT vlanTrunkPortEncapsulationType MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT vlanTrunkPortNativeVlan MIN-ACCESS read-only DESCRIPTION "Write access is not required." GROUP vtpVlanInfoEditGroup DESCRIPTION "This group must be implemented by VTP Servers. VTP Clients need not implement these objects, and must not allow VLANs to be created, modified, or destroyed using these objects." GROUP vtp4kVlanGroup DESCRIPTION "This group must be implemented by the VTP Servers which support the range of VlanIndex between 1024 and 4095." ::= { vtpMIBCompliances 2 } vtpMIBCompliance3 MODULE-COMPLIANCE STATUS current DESCRIPTION "The compliance statement for VTP implementations." MODULE -- this module MANDATORY-GROUPS { vtpBasicGroup, vtpVlanInfoGroup, -- vtpConfigNotificationsGroup, vtpStatsGroup, vtpTrunkPortGroup } OBJECT managementDomainRowStatus SYNTAX INTEGER { active(1)} -- subset of RowStatus MIN-ACCESS read-only DESCRIPTION "Write access is not required, and only one of the six enumerated values for the RowStatus textual convention need be supported, specifically: active(1)." OBJECT vlanTrunkPortRowStatus SYNTAX INTEGER { active(1)} -- subset of RowStatus MIN-ACCESS read-only DESCRIPTION "Write access is not required, and only one of the six enumerated values for the RowStatus textual convention need be supported, specifically: active(1)." OBJECT vlanTrunkPortManagementDomain MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT vlanTrunkPortEncapsulationType MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT vlanTrunkPortNativeVlan MIN-ACCESS read-only DESCRIPTION "Write access is not required." GROUP vtpVlanInfoEditGroup DESCRIPTION "This group must be implemented by VTP Servers. VTP Clients need not implement these objects, and must not allow VLANs to be created, modified, or destroyed using these objects." GROUP vtp4kVlanGroup DESCRIPTION "This group must be implemented by the VTP Servers which support the range of VlanIndex between 1024 and 4095." GROUP vtpDot1qTunnelGroup DESCRIPTION "This group is mandatory for all the ports which implement dot1qtunnel feature." OBJECT vlanTrunkPortDot1qTunnel MIN-ACCESS read-only DESCRIPTION "This object is read-only for interface which doesn't support dot1q tunnel feature." ::= { vtpMIBCompliances 3 } -- units of conformance vtpBasicGroup OBJECT-GROUP OBJECTS { vtpVersion, vtpMaxVlanStorage, vtpNotificationsEnabled, managementDomainName, managementDomainLocalMode, managementDomainConfigRevNumber, managementDomainLastUpdater, managementDomainLastChange, managementDomainTftpServer, managementDomainTftpPathname, managementDomainRowStatus } STATUS current DESCRIPTION "A collection of objects providing basic status and control of a VTP implementation." ::= { vtpMIBGroups 1 } vtpVlanInfoGroup OBJECT-GROUP OBJECTS { vtpVlanState, vtpVlanType, vtpVlanName, vtpVlanMtu, vtpVlanDot10Said, vtpVlanRingNumber, vtpVlanBridgeNumber, vtpVlanStpType, vtpVlanParentVlan, vtpVlanTranslationalVlan1, vtpVlanTranslationalVlan2, vtpVlanBridgeType, vtpVlanAreHopCount, vtpVlanSteHopCount, vtpVlanIsCRFBackup } STATUS current DESCRIPTION "A collection of objects for monitoring VLAN information." ::= { vtpMIBGroups 13 } vtpVlanInfoEditGroup OBJECT-GROUP OBJECTS { vtpVlanEditOperation, vtpVlanApplyStatus, vtpVlanEditBufferOwner, vtpVlanEditConfigRevNumber, vtpVlanEditState, vtpVlanEditType, vtpVlanEditName, vtpVlanEditMtu, vtpVlanEditDot10Said, vtpVlanEditRingNumber, vtpVlanEditBridgeNumber, vtpVlanEditStpType, vtpVlanEditParentVlan, vtpVlanEditRowStatus, vtpVlanEditTranslationalVlan1, vtpVlanEditTranslationalVlan2, vtpVlanEditBridgeType, vtpVlanEditAreHopCount, vtpVlanEditSteHopCount, vtpVlanEditIsCRFBackup } STATUS current DESCRIPTION "A collection of objects for editing VLAN information in VTP Servers." ::= { vtpMIBGroups 14 } vtpStatsGroup OBJECT-GROUP OBJECTS { vtpInSummaryAdverts, vtpInSubsetAdverts, vtpInAdvertRequests, vtpOutSummaryAdverts, vtpOutSubsetAdverts, vtpOutAdvertRequests, vtpConfigRevNumberErrors, vtpConfigDigestErrors } STATUS current DESCRIPTION "A collection of objects providing VTP statistics." ::= { vtpMIBGroups 4 } vtpTrunkPortGroup OBJECT-GROUP OBJECTS { vlanTrunkPortManagementDomain, vlanTrunkPortEncapsulationType, vlanTrunkPortVlansEnabled, vlanTrunkPortNativeVlan, vlanTrunkPortRowStatus, vlanTrunkPortSetSerialNo } STATUS current DESCRIPTION "A collection of objects providing information on trunk ports." ::= { vtpMIBGroups 5 } vtpTrunkPortGroup2 OBJECT-GROUP OBJECTS { vlanTrunkPortDynamicState, vlanTrunkPortDynamicStatus, vlanTrunkPortVtpEnabled } STATUS current DESCRIPTION " Additional functionality added to the vlanTrunkPortTable. " ::= { vtpMIBGroups 11 } vtpTrunkPortGroup3 OBJECT-GROUP OBJECTS { vlanTrunkPortEncapsulationOperType } STATUS current DESCRIPTION " Additional functionality added to the vlanTrunkPortTable. " ::= { vtpMIBGroups 15 } vtpTrunkPruningGroup OBJECT-GROUP OBJECTS { vlanTrunkPortInJoins, vlanTrunkPortOutJoins, vlanTrunkPortOldAdverts, vlanTrunkPortVlansPruningEligible, vlanTrunkPortVlansXmitJoined, vlanTrunkPortVlansRcvJoined } STATUS current DESCRIPTION "A collection of objects providing information on VLAN pruning." ::= { vtpMIBGroups 7 } vtpTrunkPruningGroup2 OBJECT-GROUP OBJECTS { managementDomainPruningState } STATUS current DESCRIPTION "A collection of object providing information on whether VLAN pruning is enabled." ::= { vtpMIBGroups 10 } vtpVersion2BasicGroup OBJECT-GROUP OBJECTS { managementDomainVersionInUse } STATUS current DESCRIPTION " The object required to indicate the version of VTP in use by a management domain." ::= { vtpMIBGroups 12 } -- vtpConfigNotificationsGroup NOTIFICATION-GROUP -- NOTIFICATIONS { vtpConfigDigestError, -- vtpConfigRevNumberError, -- vtpServerDisabled, -- vtpMtuTooBig, -- vtpVlanRingNumberConfigConflict, -- vtpVersionOneDeviceDetected, -- vlanTrunkPortDynamicStatusChange, -- vtpVlanPortLocalSegment } -- STATUS current -- DESCRIPTION -- "The notifications which a VTP implementation is -- required to implement." -- ::= { vtpMIBGroups 6 } vtp4kVlanGroup OBJECT-GROUP OBJECTS { vtpVlanTypeExt, vtpVlanEditTypeExt, vlanTrunkPortVlansEnabled2k, vlanTrunkPortVlansEnabled3k, vlanTrunkPortVlansEnabled4k, vtpVlansPruningEligible2k, vtpVlansPruningEligible3k, vtpVlansPruningEligible4k, vlanTrunkPortVlansXmitJoined2k, vlanTrunkPortVlansXmitJoined3k, vlanTrunkPortVlansXmitJoined4k, vlanTrunkPortVlansRcvJoined2k, vlanTrunkPortVlansRcvJoined3k, vlanTrunkPortVlansRcvJoined4k } STATUS current DESCRIPTION "A collection of objects providing information for VLANS with VlanIndex from 1024 to 4095." ::= { vtpMIBGroups 16 } vtpDot1qTunnelGroup OBJECT-GROUP OBJECTS { vlanTrunkPortsDot1qTag, vlanTrunkPortDot1qTunnel} STATUS current DESCRIPTION "A collection of objects providing information for dot1qtunnel feature." ::= { vtpMIBGroups 17 } END