-- ============================================================================ -- Copyright (C) by HUAWEI TECHNOLOGIES. All rights reserved. -- -- Description: -- Reference: -- Version: V1.0 -- History: -- Created by hexingjian 61140 2008-12-30 -- modified by xuxuguang 00107864 2009-12-10 -- ============================================================================ HUAWEI-L2MULTICAST-MIB DEFINITIONS ::= BEGIN IMPORTS MODULE-IDENTITY,OBJECT-TYPE, Counter32,Integer32,Unsigned32,IpAddress,Counter64 FROM SNMPv2-SMI TruthValue,TEXTUAL-CONVENTION, RowStatus,MacAddress,DisplayString FROM SNMPv2-TC MODULE-COMPLIANCE, OBJECT-GROUP FROM SNMPv2-CONF EnabledStatus FROM P-BRIDGE-MIB VlanIdOrAny FROM Q-BRIDGE-MIB InterfaceIndex,InterfaceIndexOrZero FROM IF-MIB hwDatacomm FROM HUAWEI-MIB; VlanIdOrAnyOrNone ::= TEXTUAL-CONVENTION DISPLAY-HINT "d" STATUS current DESCRIPTION "The VLAN-ID that uniquely identifies a specific VLAN, any VLAN, or no VLAN. The special values 0 and 4095 have the same meaning as described in the VlanIdOrAny and VlanIdOrNone TEXTUAL-CONVENTIONs. Note that a MIB object that is defined using this TEXTUAL-CONVENTION should clarify the meaning of 'any VLAN' and 'no VLAN' (i.e., the special values 0 and 4095)." SYNTAX Integer32 (0 | 1..4094 | 4095) hwL2MultiCastMIB MODULE-IDENTITY LAST-UPDATED "200812300000Z" ORGANIZATION "Huawei Technologies co.,Ltd." CONTACT-INFO " R&D BeiJing, Huawei Technologies co.,Ltd. Huawei Bld.,NO.3 Xinxi Rd., Shang-Di Information Industry Base, Hai-Dian District Beijing P.R. China Zip:100085 Http://www.huawei.com E-mail:support@huawei.com " DESCRIPTION "The MIB module for IGMP Snooping feature. Internet Group Management Protocol (IGMP) is the protocol used by IPv4 end hosts to indicate their interest in receiving multicast traffic for certain multicast groups to neighboring multicast routers. IGMP Snooping is a switch protocol. A switch that implements IGMP Snooping listens to the IGMP messages exchanged between the hosts and router, then provides selective transmission of multicast traffic based on multicast mac destination address or multicast group address." ::= { hwDatacomm 181 } -- Textual Convention HWPortType ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "type of port : invalid(1):invalid type, pw(2) : pw type, switchport(3) : switchport type, dot1q(4): dot1q sub-interface type, termination(5): termination sub-interface type, board(6): interface board number, VlanPort(7): Vlanif port, qinq-batch-config(9): batch config qinq port ce VLAN ID, dot1q-termination-batch-config(10): batch config dot1q termination port ce VLAN ID" SYNTAX INTEGER { invalid(1), pw(2), switchport(3), dot1q(4), termination(5), board(6), vlanPort(7), qinq-batch-config(9), dot1q-termination-batch-config(10) } hwIgspMibObject OBJECT IDENTIFIER ::= { hwL2MultiCastMIB 1 } -- -- The hwIgspSystemInfo group. -- hwIgspSystemInfo OBJECT IDENTIFIER ::= { hwIgspMibObject 1 } hwIgmpSnoopingEnabled OBJECT-TYPE SYNTAX EnabledStatus MAX-ACCESS read-write STATUS current DESCRIPTION "IGMP snooping is enabled or disabled in the global view: 1: enabled 2: disabled The default value is 2. " ::= { hwIgspSystemInfo 1 } hwSendQueryEnabled OBJECT-TYPE SYNTAX EnabledStatus MAX-ACCESS read-write STATUS current DESCRIPTION "The sending of query packets is enabled or disabled: 1: enabled 2: disabled The default value is 2. Note: Ensure that you query and configure this object after hwIgmpSnoopingEnabled is configured. " ::= { hwIgspSystemInfo 2 } hwSendQuerySourceIpAddr OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-write STATUS current DESCRIPTION "The source IP addresses of the Query messages sent by a device. The value ranges from 0.0.0.1 to 223.255.255.255. The default value is 192.168.0.1. " ::= { hwIgspSystemInfo 3} hwL2mcCacTrapInterval OBJECT-TYPE SYNTAX Integer32(0..1200) MAX-ACCESS read-write STATUS current DESCRIPTION "The CAC trap interval. The default is zero." ::= { hwIgspSystemInfo 4} hwL2mcPerformanceStatisticsInterval OBJECT-TYPE SYNTAX Integer32(5 |15 | 30 | 60) MAX-ACCESS read-write STATUS current DESCRIPTION "The Performance statistic interval. The default is 15 minute." ::= { hwIgspSystemInfo 5} -- -- The hwL2mcCfgInfo group. -- hwL2mcCfgInfo OBJECT IDENTIFIER ::= { hwIgspMibObject 2 } hwL2mcCfgTable OBJECT-TYPE SYNTAX SEQUENCE OF HWL2mcCfgEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table describes the configurations of IGMP snooping in a VLAN or a VSI." ::= { hwL2mcCfgInfo 1 } hwL2mcCfgEntry OBJECT-TYPE SYNTAX HWL2mcCfgEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry is created for each active VLAN or VSI in the device and deleted when the VLAN or VSI becomes inactive." INDEX { hwL2mcVlanIndex, hwL2mcVsiName } ::= { hwL2mcCfgTable 1 } HWL2mcCfgEntry ::= SEQUENCE { hwL2mcVlanIndex VlanIdOrAny, hwL2mcVsiName DisplayString, hwL2mcEnabled EnabledStatus, hwL2mcRouterAgingTime Integer32, hwL2mcMaxQueryRespTime Integer32, hwL2mcLastMemQueryInterval Integer32, hwL2mcQueryInterval Integer32, hwL2mcRobustCount Integer32, hwL2mcCheckRouterAlert TruthValue, hwL2mcSendRouterAlert TruthValue, hwL2mcIgmpVersion INTEGER , hwL2mcFwdMode INTEGER, hwL2mcPromptLeaveEnable EnabledStatus, hwL2mcPromptLeaveAclNum Integer32, hwL2mcRouterPortLearningEnable EnabledStatus, hwL2mcReportSuppressEnable EnabledStatus, hwL2mcIgmpQuerierEnable EnabledStatus, hwL2mcIgmpSsmMappingEnable EnabledStatus, hwL2mcSsmAclNum Integer32, hwL2mcProxyRouterProtocolPass TruthValue, hwL2mcAsmSsmFlag Integer32, hwL2mcSrcLifeTime Integer32, hwL2mcPerformanceStatistics EnabledStatus, hwL2mcQuerierElection EnabledStatus, hwETrackEnable EnabledStatus, hwL2mcBackupQueryFwd Integer32, hwL2mcBackupReportFwd Integer32, hwL2mcQuerySuppress Integer32, hwL2mcRtLearnRingLinkage TruthValue, hwL2mcRowStatus RowStatus } hwL2mcVlanIndex OBJECT-TYPE SYNTAX VlanIdOrAny MAX-ACCESS not-accessible STATUS current DESCRIPTION "The VLAN ID, which is the configuration index in a VLAN. If a VSI is specified, the value is 4095. The value ranges from 1 to 4095. " ::= { hwL2mcCfgEntry 1 } hwL2mcVsiName OBJECT-TYPE SYNTAX DisplayString(SIZE (0..31)) MAX-ACCESS not-accessible STATUS current DESCRIPTION "The name of a VSI. If a VLAN is specified, the value is 32." ::= { hwL2mcCfgEntry 2 } hwL2mcEnabled OBJECT-TYPE SYNTAX EnabledStatus MAX-ACCESS read-create STATUS current DESCRIPTION "Whether IGMP snooping is enabled in a VLAN or a VSI: 1:enabled 2:disabled The default value is 2. " ::= { hwL2mcCfgEntry 3 } hwL2mcRouterAgingTime OBJECT-TYPE SYNTAX Integer32(1..1000) MAX-ACCESS read-create STATUS current DESCRIPTION "The aging time of an interface on a router. The value ranges from 1 to 1000, in seconds. The default value is 180, which router port is created by Igmp Query message. And when it is created by PIM hello messge, the default value is the time of Holdtime in the message. " ::= { hwL2mcCfgEntry 4 } hwL2mcMaxQueryRespTime OBJECT-TYPE SYNTAX Integer32(1..25) MAX-ACCESS read-create STATUS current DESCRIPTION "The maximum response time. The value ranges from 1 to 25, in seconds. The default value is 10, in seconds. " ::= { hwL2mcCfgEntry 5 } hwL2mcLastMemQueryInterval OBJECT-TYPE SYNTAX Integer32(1..5) MAX-ACCESS read-create STATUS current DESCRIPTION "The last member query interval. The value ranges from 1 to 5, in seconds. The default value is 1, in seconds. " ::= { hwL2mcCfgEntry 6 } hwL2mcQueryInterval OBJECT-TYPE SYNTAX Integer32(1..65535) MAX-ACCESS read-create STATUS current DESCRIPTION "The query interval. The value ranges from 1 to 65535, in seconds. The default value is 60, in seconds. " ::= { hwL2mcCfgEntry 7 } hwL2mcRobustCount OBJECT-TYPE SYNTAX Integer32(2..5) MAX-ACCESS read-create STATUS current DESCRIPTION "The robustness variable. The value ranges from 2 to 5. The default value is 2. " ::= { hwL2mcCfgEntry 8 } hwL2mcCheckRouterAlert OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-create STATUS current DESCRIPTION "Whether to check the router-alert of a packet. The default value is false. " ::= { hwL2mcCfgEntry 9 } hwL2mcSendRouterAlert OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-create STATUS current DESCRIPTION "Whether to send the router-alert of a packet. The default value is true. " ::= { hwL2mcCfgEntry 10 } hwL2mcIgmpVersion OBJECT-TYPE SYNTAX INTEGER { version1(1), version2(2), version3(3) } MAX-ACCESS read-create STATUS current DESCRIPTION "The version of the IGMP packets. The value ranges from 1 to 3. The default value is 2. " ::= { hwL2mcCfgEntry 11 } hwL2mcFwdMode OBJECT-TYPE SYNTAX INTEGER { ip(1), mac(2) } MAX-ACCESS read-create STATUS current DESCRIPTION "The forwarding mode: 1: IP 2: MAC The default value is 1. " ::= { hwL2mcCfgEntry 12 } hwL2mcPromptLeaveEnable OBJECT-TYPE SYNTAX EnabledStatus MAX-ACCESS read-create STATUS current DESCRIPTION "Whether the prompt leave is enabled: 1: enabled 2: disabled The default value is 2. " ::= { hwL2mcCfgEntry 13 } hwL2mcPromptLeaveAclNum OBJECT-TYPE SYNTAX Integer32(0|2000..3999) MAX-ACCESS read-create STATUS current DESCRIPTION "Whether the prompt leave complies with the ACL rules. The ACL number can be set. The ACL number ranges from 2000 to 3999. The default value is 0, indicating that no ACL number is set. " ::= { hwL2mcCfgEntry 14 } hwL2mcRouterPortLearningEnable OBJECT-TYPE SYNTAX EnabledStatus MAX-ACCESS read-create STATUS current DESCRIPTION "Whether interface learning is enabled or not in a VLAN: 1: enabled 2: disabled The default value is 1. " ::= { hwL2mcCfgEntry 15 } hwL2mcReportSuppressEnable OBJECT-TYPE SYNTAX EnabledStatus MAX-ACCESS read-create STATUS current DESCRIPTION "Whether the suppression of the IGMP Report message (proxy) is enabled: 1: enabled 2: disabled The default value is 2. " ::= { hwL2mcCfgEntry 16 } hwL2mcIgmpQuerierEnable OBJECT-TYPE SYNTAX EnabledStatus MAX-ACCESS read-create STATUS current DESCRIPTION "Whether the querier is enabled: 1: enabled 2: disabled The default value is 2. " ::= { hwL2mcCfgEntry 17 } hwL2mcIgmpSsmMappingEnable OBJECT-TYPE SYNTAX EnabledStatus MAX-ACCESS read-create STATUS current DESCRIPTION "Whether Ssm-Mapping is enabled: 1: enabled 2: disabled The default value is 2. " ::= { hwL2mcCfgEntry 18 } hwL2mcSsmAclNum OBJECT-TYPE SYNTAX Integer32(0|2000..2999) MAX-ACCESS read-create STATUS current DESCRIPTION "That SSM complies with the ACL number. The ACL number ranges from 2000 to 2999. The default value is 0, indicating that no ACL number is set. " ::= { hwL2mcCfgEntry 19 } hwL2mcProxyRouterProtocolPass OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-create STATUS current DESCRIPTION "Whether protocol packets are allowed to pass a router port when proxy is enabled. The default value is false. " ::= { hwL2mcCfgEntry 20 } hwL2mcAsmSsmFlag OBJECT-TYPE SYNTAX Integer32(1..3) MAX-ACCESS read-create STATUS current DESCRIPTION "That restric study: 1: asm-ssm 2: asm-only 3: ssm-only The default value is 1. " ::= { hwL2mcCfgEntry 21 } hwL2mcSrcLifeTime OBJECT-TYPE SYNTAX Integer32(60..1000) MAX-ACCESS read-create STATUS current DESCRIPTION "That source aging time: range from 60 to 1000 The default value is 210. " ::= { hwL2mcCfgEntry 22 } hwL2mcPerformanceStatistics OBJECT-TYPE SYNTAX EnabledStatus MAX-ACCESS read-create STATUS current DESCRIPTION "That performance statistic is enabled: 1: enabled 2: disabled The default value is 2. " ::= { hwL2mcCfgEntry 23 } hwL2mcQuerierElection OBJECT-TYPE SYNTAX EnabledStatus MAX-ACCESS read-create STATUS current DESCRIPTION "That querier election is enabled: 1: enabled 2: disabled The default value is 2. " ::= { hwL2mcCfgEntry 24 } hwETrackEnable OBJECT-TYPE SYNTAX EnabledStatus MAX-ACCESS read-create STATUS current DESCRIPTION "The host explicity track is enabled: 1: enabled 2: disabled The default value is 2. " ::= { hwL2mcCfgEntry 25 } hwL2mcBackupQueryFwd OBJECT-TYPE SYNTAX Integer32(1..3) MAX-ACCESS read-create STATUS current DESCRIPTION "That IGMP query forward : 1: Do not forward; 2: Forward without replace source MAC address; 3: Forward with replace source MAC address; The default value is 1. " ::= { hwL2mcCfgEntry 26 } hwL2mcBackupReportFwd OBJECT-TYPE SYNTAX Integer32(1..3) MAX-ACCESS read-create STATUS current DESCRIPTION "That IGMP report forward : 1: Do not forward; 2: Forward without replace source MAC address; 3: Forward with replace source MAC address; The default value is 1. " ::= { hwL2mcCfgEntry 27 } hwL2mcQuerySuppress OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-create STATUS current DESCRIPTION "Whether supress IGMP query packet or time of suppress interval. " ::= { hwL2mcCfgEntry 28 } hwL2mcRtLearnRingLinkage OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-create STATUS current DESCRIPTION "Whether responed to link state for SEP. " ::= { hwL2mcCfgEntry 29 } hwL2mcRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "The row status." ::= { hwL2mcCfgEntry 100 } -- -- The hwL2mcStatisticsInfo group. -- hwL2mcStatisticsInfo OBJECT IDENTIFIER ::= { hwIgspMibObject 3 } hwL2mcStatisticsTable OBJECT-TYPE SYNTAX SEQUENCE OF HWL2mcStatisticsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Table contains VLAN or VSI statistics information for IGMP Snooping." ::= { hwL2mcStatisticsInfo 1 } hwL2mcStatisticsEntry OBJECT-TYPE SYNTAX HWL2mcStatisticsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry is created for each active VLAN or VSI in the device and deleted when the VLAN or VSI becomes inactive." INDEX { hwL2mcStatsVlanIndex, hwL2mcStatsVsiName } ::= { hwL2mcStatisticsTable 1 } HWL2mcStatisticsEntry ::= SEQUENCE { hwL2mcStatsVlanIndex VlanIdOrAny, hwL2mcStatsVsiName DisplayString, hwL2mcRecvIgmpV1ReportNum Counter32, hwL2mcRecvIgmpV2ReportNum Counter32, hwL2mcRecvIgmpV3ReportNum Counter32, hwL2mcRecvIgmpLeaveNum Counter32, hwL2mcRecvIgmpV1QueryNum Counter32, hwL2mcRecvIgmpV2QueryNum Counter32, hwL2mcRecvIgmpV3QueryNum Counter32, hwL2mcRecvPimHelloNum Counter32, hwL2mcSendQueryNum Counter32 , hwL2mcSendQuerySourceNum Counter32, hwL2mcProxyGenQueryNum Counter32, hwL2mcProxyGroupQueryNum Counter32, hwL2mcProxyGroupSourceQueryNum Counter32, hwL2mcIgmpPacketClearStats TruthValue } hwL2mcStatsVlanIndex OBJECT-TYPE SYNTAX VlanIdOrAny MAX-ACCESS not-accessible STATUS current DESCRIPTION "The VLAN ID, which is the configuration index in a VLAN. If a VSI is specified, the value is 4095. The value ranges from 1 to 4095. " ::= { hwL2mcStatisticsEntry 1 } hwL2mcStatsVsiName OBJECT-TYPE SYNTAX DisplayString(SIZE (0..31)) MAX-ACCESS not-accessible STATUS current DESCRIPTION "The name of a VSI. If a VLAN is specified, the value is 32." ::= { hwL2mcStatisticsEntry 2 } hwL2mcRecvIgmpV1ReportNum OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of IGMPv1 Report messages received in a VLAN or a VSI." ::= { hwL2mcStatisticsEntry 3 } hwL2mcRecvIgmpV2ReportNum OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of IGMPv2 Report messages received in a VLAN or a VSI." ::= { hwL2mcStatisticsEntry 4 } hwL2mcRecvIgmpV3ReportNum OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of IGMPv3 Report messages received in a VLAN or a VSI." ::= { hwL2mcStatisticsEntry 5 } hwL2mcRecvIgmpLeaveNum OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of IGMP Leave messages received in a VLAN or a VSI." ::= { hwL2mcStatisticsEntry 6 } hwL2mcRecvIgmpV1QueryNum OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of IGMPv1 Query messages received in a VLAN or a VSI." ::= { hwL2mcStatisticsEntry 7 } hwL2mcRecvIgmpV2QueryNum OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of IGMPv2 Query messages received in a VLAN or a VSI." ::= { hwL2mcStatisticsEntry 8 } hwL2mcRecvIgmpV3QueryNum OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of IGMPv3 Query messages received in a VLAN or a VSI." ::= { hwL2mcStatisticsEntry 9 } hwL2mcRecvPimHelloNum OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of PIM Hello messages received in a VLAN or a VSI." ::= { hwL2mcStatisticsEntry 10 } hwL2mcSendQueryNum OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of IGMP Query messages (the source address is 0) in a VLAN or a VSI." ::= { hwL2mcStatisticsEntry 11 } hwL2mcSendQuerySourceNum OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of IGMP Query messages (the source address is not 0) in a VLAN or a VSI." ::= { hwL2mcStatisticsEntry 12 } hwL2mcProxyGenQueryNum OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of Query messages sent by the proxy in a VLAN or a VSI." ::= { hwL2mcStatisticsEntry 13 } hwL2mcProxyGroupQueryNum OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of Query messages sent by the proxy in a VLAN or a VSI to a specified group." ::= { hwL2mcStatisticsEntry 14 } hwL2mcProxyGroupSourceQueryNum OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of Query messages sent by the proxy in a VLAN or a VSI to a specified source group." ::= { hwL2mcStatisticsEntry 15 } hwL2mcIgmpPacketClearStats OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "Whether to clear the statistics of IGMP snooping. If the value is 1, it indicates that the statistics need to be cleared." ::= { hwL2mcStatisticsEntry 30 } -- -- The hwL2mcFwdInfo group. -- hwL2mcFwdInfo OBJECT IDENTIFIER ::= { hwIgspMibObject 4 } hwL2mcFwdTable OBJECT-TYPE SYNTAX SEQUENCE OF HWL2mcFwdEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Table contains l2 multicast forward information for IGMP Snooping." ::= { hwL2mcFwdInfo 1 } hwL2mcFwdEntry OBJECT-TYPE SYNTAX HWL2mcFwdEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry is created for each active VLAN or VSI in the device create a forwarding table entry and delete when a forwarding table entry deleted." INDEX { hwL2mcFwdVlanIndex, hwL2mcFwdVsiName, hwL2mcFwdGroupAddress, hwL2mcFwdSourceAddress, hwL2mcFwdPortType, hwL2mcFwdPortIfIndex, hwL2mcFwdPortPeId, hwL2mcFwdPortCeId, hwL2mcFwdPeerAddress, hwL2mcFwdVcOrSiteId } ::= { hwL2mcFwdTable 1 } HWL2mcFwdEntry ::= SEQUENCE { hwL2mcFwdVlanIndex VlanIdOrAny, hwL2mcFwdVsiName DisplayString, hwL2mcFwdGroupAddress IpAddress, hwL2mcFwdSourceAddress IpAddress, hwL2mcFwdPortType HWPortType, hwL2mcFwdPortIfIndex InterfaceIndexOrZero, hwL2mcFwdPortPeId VlanIdOrAny, hwL2mcFwdPortCeId VlanIdOrAny, hwL2mcFwdPeerAddress IpAddress, hwL2mcFwdVcOrSiteId Unsigned32, hwL2mcFwdAddressType INTEGER, hwL2mcFwdHostFlag1 INTEGER, hwL2mcFwdHostFlag2 INTEGER, hwL2mcFwdHostFlag3 INTEGER, hwL2mcFwdHostFlag4 INTEGER } hwL2mcFwdVlanIndex OBJECT-TYPE SYNTAX VlanIdOrAny MAX-ACCESS not-accessible STATUS current DESCRIPTION "The VLAN ID, which is the configuration index in a VLAN. If a VSI is specified, the value is 4095. The value ranges from 1 to 4095. " ::= { hwL2mcFwdEntry 1 } hwL2mcFwdVsiName OBJECT-TYPE SYNTAX DisplayString(SIZE (0..31)) MAX-ACCESS not-accessible STATUS current DESCRIPTION "The name of a VSI. If a VLAN is specified, the value is 32." ::= { hwL2mcFwdEntry 2 } hwL2mcFwdGroupAddress OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS not-accessible STATUS current DESCRIPTION "The group address of a multicast group. In the case of MAC forwarding, the group address is the smallest of 32 IP addresses." ::= { hwL2mcFwdEntry 3 } hwL2mcFwdSourceAddress OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS not-accessible STATUS current DESCRIPTION "The source IP address of a multicast group." ::= { hwL2mcFwdEntry 4 } hwL2mcFwdPortType OBJECT-TYPE SYNTAX HWPortType MAX-ACCESS not-accessible STATUS current DESCRIPTION "The interface type: 1: Invalid 2: PW interface 3: L2 interface 4: Encapsulation sub-interface 5: Termination sub-interface 6: Interface Board 7: Vlanif Port " ::= { hwL2mcFwdEntry 5 } hwL2mcFwdPortIfIndex OBJECT-TYPE SYNTAX InterfaceIndexOrZero MAX-ACCESS not-accessible STATUS current DESCRIPTION "The interface index. The value 0 indicates that the interface index is invalid." ::= { hwL2mcFwdEntry 6 } hwL2mcFwdPortPeId OBJECT-TYPE SYNTAX VlanIdOrAny MAX-ACCESS not-accessible STATUS current DESCRIPTION "The PE VID of an interface. The value ranges from 1 to 4095. The value 4095 indicates that the PE VID is invalid. " ::= { hwL2mcFwdEntry 7 } hwL2mcFwdPortCeId OBJECT-TYPE SYNTAX VlanIdOrAny MAX-ACCESS not-accessible STATUS current DESCRIPTION "The CE VID of an interface. The value ranges from 1 to 4095. The value 4095 indicates that the CE VID is invalid. " ::= { hwL2mcFwdEntry 8 } hwL2mcFwdPeerAddress OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS not-accessible STATUS current DESCRIPTION "The peer IP address of a PW interface. The value 0.0.0.0 indicates that the IP address is invalid." ::= { hwL2mcFwdEntry 9 } hwL2mcFwdVcOrSiteId OBJECT-TYPE SYNTAX Unsigned32(1..4294967295) MAX-ACCESS not-accessible STATUS current DESCRIPTION "The VC ID or SITE ID of a PW interface." ::= { hwL2mcFwdEntry 10 } hwL2mcFwdAddressType OBJECT-TYPE SYNTAX INTEGER { ip(1), mac(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "The address type of an entry: 1: IP 2: MAC The default value is 1. " ::= { hwL2mcFwdEntry 11 } hwL2mcFwdHostFlag1 OBJECT-TYPE SYNTAX INTEGER { static(1), dynamic(2), staticDynamic(3), invalid(4) } MAX-ACCESS read-only STATUS current DESCRIPTION "The mode to create an interface on the host: 1: static 2: dynamic 3: static and dynamic 4: invalid " ::= { hwL2mcFwdEntry 18 } hwL2mcFwdHostFlag2 OBJECT-TYPE SYNTAX INTEGER { nonMapping(1), mapping(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "Whether an interface on the host is created through SSM-mapping: 1: non-mapping 2: mapping " ::= { hwL2mcFwdEntry 19 } hwL2mcFwdHostFlag3 OBJECT-TYPE SYNTAX INTEGER { host(1), router(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "The type of an interface created on a router: 1: Interface connected to the host 2: Router interface that replicates multicast data flows " ::= { hwL2mcFwdEntry 20 } hwL2mcFwdHostFlag4 OBJECT-TYPE SYNTAX INTEGER { port(1), static(2), both(3) } MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates (S, G) table created : 1: from port; 2: from static; 3: from both the default value is 1 " ::= { hwL2mcFwdEntry 21 } -- -- The hwGroupInfo group. -- hwL2mcGroupInfo OBJECT IDENTIFIER ::= { hwIgspMibObject 5 } hwL2mcGroupInfoTable OBJECT-TYPE SYNTAX SEQUENCE OF HWL2mcGroupInfoEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Table contains l2 multicast group information for IGMP Snooping." ::= { hwL2mcGroupInfo 1 } hwL2mcGroupInfoEntry OBJECT-TYPE SYNTAX HWL2mcGroupInfoEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry is created for each active VLAN or VSI in the device create a forwarding table entry and delete when a forwarding table entry deleted." INDEX { hwL2mcGroupVlanIndex, hwL2mcGroupVsiName, hwL2mcGroupGroupAddress, hwL2mcGroupSourceAddress, hwL2mcPortType, hwL2mcGroupPortIfIndex, hwL2mcGroupPortPeId, hwL2mcGroupPortCeId, hwL2mcGroupPeerAddress, hwL2mcGroupVcOrSiteId } ::= { hwL2mcGroupInfoTable 1 } HWL2mcGroupInfoEntry ::= SEQUENCE { hwL2mcGroupVlanIndex VlanIdOrAny, hwL2mcGroupVsiName DisplayString, hwL2mcGroupGroupAddress IpAddress, hwL2mcGroupSourceAddress IpAddress, hwL2mcPortType HWPortType, hwL2mcGroupPortIfIndex InterfaceIndexOrZero, hwL2mcGroupPortPeId VlanIdOrAny, hwL2mcGroupPortCeId VlanIdOrAny, hwL2mcGroupPeerAddress IpAddress, hwL2mcGroupVcOrSiteId Unsigned32, hwL2mcSourceUpTime Counter32, hwL2mcSourceExpires Counter32, hwL2mcGroupUpTime Counter32, hwL2mcGroupExpires Counter32, hwL2mcGroupFilterFlag INTEGER, hwL2mcGroupHostFlag1 INTEGER, hwL2mcGroupHostFlag2 INTEGER, hwL2mcGroupRowStatus RowStatus } hwL2mcGroupVlanIndex OBJECT-TYPE SYNTAX VlanIdOrAny MAX-ACCESS not-accessible STATUS current DESCRIPTION "The VLAN ID, which is the configuration index in a VLAN. If a VSI is specified, the value is 4095. The value ranges from 1 to 4095. " ::= { hwL2mcGroupInfoEntry 1 } hwL2mcGroupVsiName OBJECT-TYPE SYNTAX DisplayString(SIZE (0..31)) MAX-ACCESS not-accessible STATUS current DESCRIPTION "The name of a VSI. If a VLAN is specified, the value is 32." ::= { hwL2mcGroupInfoEntry 2 } hwL2mcGroupGroupAddress OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS not-accessible STATUS current DESCRIPTION "The IP address of a multicast group." ::= { hwL2mcGroupInfoEntry 3 } hwL2mcGroupSourceAddress OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS not-accessible STATUS current DESCRIPTION "The source IP address of a multicast group." ::= { hwL2mcGroupInfoEntry 4 } hwL2mcPortType OBJECT-TYPE SYNTAX HWPortType MAX-ACCESS not-accessible STATUS current DESCRIPTION "The interface type: 1: Invalid 2: PW interface 3: L2 interface 4: Encapsulation sub-interface 5: Termination sub-interface 6: Interface Board 7: Vlanif Port " ::= { hwL2mcGroupInfoEntry 5 } hwL2mcGroupPortIfIndex OBJECT-TYPE SYNTAX InterfaceIndexOrZero MAX-ACCESS not-accessible STATUS current DESCRIPTION "The interface index. The value 0 indicates that the interface index is invalid." ::= { hwL2mcGroupInfoEntry 6 } hwL2mcGroupPortPeId OBJECT-TYPE SYNTAX VlanIdOrAny MAX-ACCESS not-accessible STATUS current DESCRIPTION "The PE VID of an interface. The value ranges from 1 to 4095. The value 4095 indicates that the PE VID is invalid. " ::= { hwL2mcGroupInfoEntry 7 } hwL2mcGroupPortCeId OBJECT-TYPE SYNTAX VlanIdOrAny MAX-ACCESS not-accessible STATUS current DESCRIPTION "The CE VID of an interface. The value ranges from 1 to 4095. The value 0 indicates that the PE VID is invalid. " ::= { hwL2mcGroupInfoEntry 8 } hwL2mcGroupPeerAddress OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS not-accessible STATUS current DESCRIPTION "The peer IP address of a PW interface. The value 0.0.0.0 indicates that the IP address is invalid." ::= { hwL2mcGroupInfoEntry 9 } hwL2mcGroupVcOrSiteId OBJECT-TYPE SYNTAX Unsigned32(1..4294967295) MAX-ACCESS not-accessible STATUS current DESCRIPTION "The VC ID or SITE ID of a PW interface." ::= { hwL2mcGroupInfoEntry 10 } hwL2mcSourceUpTime OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "How long the source group exists in the forwarding entry." ::= { hwL2mcGroupInfoEntry 14 } hwL2mcSourceExpires OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The timeout period of the source group in the forwarding entry, that is, the aging time of the source group." ::= { hwL2mcGroupInfoEntry 15 } hwL2mcGroupUpTime OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "How long the group exists in the forwarding entry." ::= { hwL2mcGroupInfoEntry 16 } hwL2mcGroupExpires OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "When the group expires in the forwarding entry, that is, the aging time of the source group." ::= { hwL2mcGroupInfoEntry 17 } hwL2mcGroupFilterFlag OBJECT-TYPE SYNTAX INTEGER { include(1), exclude(2), invalid(3) } MAX-ACCESS read-only STATUS current DESCRIPTION "The filtering mode: 1: include 2: exclude 3: invalid " ::= { hwL2mcGroupInfoEntry 18 } hwL2mcGroupHostFlag1 OBJECT-TYPE SYNTAX INTEGER { static(1), dynamic(2), staticDynamic(3), invalid(4) } MAX-ACCESS read-only STATUS current DESCRIPTION "The mode to create an interface on the host: 1: static 2: dynamic 3: static and dynamic 4: invalid " ::= { hwL2mcGroupInfoEntry 19 } hwL2mcGroupHostFlag2 OBJECT-TYPE SYNTAX INTEGER { nonMapping(1), mapping(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "Whether an interface on the host is created through SSM-mapping: 1: non-mapping 2: mapping " ::= { hwL2mcGroupInfoEntry 20 } hwL2mcGroupRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-only STATUS current DESCRIPTION "The row status." ::= { hwL2mcGroupInfoEntry 100 } -- -- The hwL2mcGroupCfgInfo group. -- hwL2mcGroupCfgInfo OBJECT IDENTIFIER ::= { hwIgspMibObject 6 } hwL2mcGroupCfgTable OBJECT-TYPE SYNTAX SEQUENCE OF HWL2mcGroupCfgEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Table contains l2 multicast static group information for IGMP Snooping." ::= { hwL2mcGroupCfgInfo 1 } hwL2mcGroupCfgEntry OBJECT-TYPE SYNTAX HWL2mcGroupCfgEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry is created for each active VLAN or VSI in the device create a static group entry and delete when a static group entry deleted." INDEX { hwGroupCfgPortType, hwGroupCfgPortIfIndex, hwGroupCfgPortPeId, hwGroupCfgPortCeId, hwGroupCfgPeerAddress, hwGroupCfgVcOrSiteId, hwGroupCfgVlanIndex, hwGroupCfgVsiName, hwGroupCfgGroupAddress, hwGroupCfgSourceAddress } ::= { hwL2mcGroupCfgTable 1 } HWL2mcGroupCfgEntry ::= SEQUENCE { hwGroupCfgPortType HWPortType, hwGroupCfgPortIfIndex InterfaceIndexOrZero, hwGroupCfgPortPeId VlanIdOrAny, hwGroupCfgPortCeId VlanIdOrAny, hwGroupCfgPeerAddress IpAddress, hwGroupCfgVcOrSiteId Unsigned32, hwGroupCfgVlanIndex VlanIdOrAny, hwGroupCfgVsiName DisplayString, hwGroupCfgGroupAddress IpAddress, hwGroupCfgSourceAddress IpAddress, hwGroupCfgRowStatus RowStatus } hwGroupCfgPortType OBJECT-TYPE SYNTAX HWPortType MAX-ACCESS not-accessible STATUS current DESCRIPTION "The interface type: 1: Invalid 2: PW interface 3: L2 interface 4: Encapsulation sub-interface 5: Termination sub-interface 6: Interface Board 7: Vlanif Port " ::= { hwL2mcGroupCfgEntry 1 } hwGroupCfgPortIfIndex OBJECT-TYPE SYNTAX InterfaceIndexOrZero MAX-ACCESS not-accessible STATUS current DESCRIPTION "The interface index. The value 0 indicates that the interface index is invalid." ::= { hwL2mcGroupCfgEntry 2 } hwGroupCfgPortPeId OBJECT-TYPE SYNTAX VlanIdOrAny MAX-ACCESS not-accessible STATUS current DESCRIPTION "The PE VID of an interface. The value ranges from 1 to 4095. The value 4095 indicates that the PE VID is invalid. " ::= { hwL2mcGroupCfgEntry 3 } hwGroupCfgPortCeId OBJECT-TYPE SYNTAX VlanIdOrAny MAX-ACCESS not-accessible STATUS current DESCRIPTION "The CE VID of an interface. The value ranges from 1 to 4095. The value 0 indicates that the PE VID is invalid. " ::= { hwL2mcGroupCfgEntry 4 } hwGroupCfgPeerAddress OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS not-accessible STATUS current DESCRIPTION "The peer IP address of a PW interface. The value 0.0.0.0 indicates that the IP address is invalid." ::= { hwL2mcGroupCfgEntry 5 } hwGroupCfgVcOrSiteId OBJECT-TYPE SYNTAX Unsigned32(1..4294967295) MAX-ACCESS not-accessible STATUS current DESCRIPTION "The VC ID or SITE ID of a PW interface." ::= { hwL2mcGroupCfgEntry 6 } hwGroupCfgVlanIndex OBJECT-TYPE SYNTAX VlanIdOrAny MAX-ACCESS not-accessible STATUS current DESCRIPTION "The VLAN ID, which is the configuration index in a VLAN. If a VSI is specified, the value is 4095. The value ranges from 1 to 4095. " ::= { hwL2mcGroupCfgEntry 7 } hwGroupCfgVsiName OBJECT-TYPE SYNTAX DisplayString(SIZE (0..31)) MAX-ACCESS not-accessible STATUS current DESCRIPTION "The name of a VSI. If a VLAN is specified, the value is 32." ::= { hwL2mcGroupCfgEntry 8 } hwGroupCfgGroupAddress OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS not-accessible STATUS current DESCRIPTION "The group address of a multicast group. In the case of MAC forwarding, the group address is the smallest of 32 IP addresses." ::= { hwL2mcGroupCfgEntry 9 } hwGroupCfgSourceAddress OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS not-accessible STATUS current DESCRIPTION "The source IP address of a multicast group." ::= { hwL2mcGroupCfgEntry 10 } hwGroupCfgRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "The row status." ::= { hwL2mcGroupCfgEntry 100 } -- -- The hwL2mcSsmSourceInfo group. -- hwL2mcSsmSourceInfo OBJECT IDENTIFIER ::= { hwIgspMibObject 7 } hwL2mcSsmSourceTable OBJECT-TYPE SYNTAX SEQUENCE OF HWL2mcSsmSourceEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains the configuration of the source address list of SSM-Mapping." ::= { hwL2mcSsmSourceInfo 1 } hwL2mcSsmSourceEntry OBJECT-TYPE SYNTAX HWL2mcSsmSourceEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry is created for each active VLAN or VSI in the device add an entry for SSM-Mapping." INDEX { hwL2mcSsmSourceVlanIndex, hwL2mcSsmSourceVsiName, hwL2mcSsmGroupAddress, hwL2mcSsmGroupLen, hwL2mcSsmSourceAddress } ::= { hwL2mcSsmSourceTable 1 } HWL2mcSsmSourceEntry ::= SEQUENCE { hwL2mcSsmSourceVlanIndex VlanIdOrAny, hwL2mcSsmSourceVsiName DisplayString, hwL2mcSsmGroupAddress IpAddress, hwL2mcSsmGroupLen Integer32, hwL2mcSsmSourceAddress IpAddress, hwL2mcSsmSourceRowStatus RowStatus } hwL2mcSsmSourceVlanIndex OBJECT-TYPE SYNTAX VlanIdOrAny MAX-ACCESS not-accessible STATUS current DESCRIPTION "The VLAN ID, which is the configuration index in a VLAN. If a VSI is specified, the value is 4095. The value ranges from 1 to 4095. " ::= { hwL2mcSsmSourceEntry 1 } hwL2mcSsmSourceVsiName OBJECT-TYPE SYNTAX DisplayString(SIZE (0..31)) MAX-ACCESS not-accessible STATUS current DESCRIPTION "The name of a VSI. If a VLAN is specified, the value is 32." ::= { hwL2mcSsmSourceEntry 2 } hwL2mcSsmGroupAddress OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS not-accessible STATUS current DESCRIPTION "The IP address of a multicast group. " ::= { hwL2mcSsmSourceEntry 3 } hwL2mcSsmGroupLen OBJECT-TYPE SYNTAX Integer32(4..32) MAX-ACCESS not-accessible STATUS current DESCRIPTION "The mask length of a multicast group." ::= { hwL2mcSsmSourceEntry 4 } hwL2mcSsmSourceAddress OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS not-accessible STATUS current DESCRIPTION "The source address of SSM-Mapping, which serves as an index of this table." ::= { hwL2mcSsmSourceEntry 5 } hwL2mcSsmSourceRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "The row status." ::= { hwL2mcSsmSourceEntry 100 } -- -- The hwL2mcPortGroupPolicyCfgInfo group. -- hwL2mcPortGroupPolicyCfgInfo OBJECT IDENTIFIER ::= { hwIgspMibObject 8 } hwL2mcPortGroupPolicyCfgTable OBJECT-TYPE SYNTAX SEQUENCE OF HWL2mcPortGroupPolicyCfgEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "In this table, you can query or configure a group policy to filter entries on a port." ::= { hwL2mcPortGroupPolicyCfgInfo 1 } hwL2mcPortGroupPolicyCfgEntry OBJECT-TYPE SYNTAX HWL2mcPortGroupPolicyCfgEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry is created for each active VLAN or VSI in the device when a group policy added." INDEX { hwPortGroupPolicyPortType, hwPortGroupPolicyPortIfIndex, hwPortGroupPolicyPortPeId, hwPortGroupPolicyPortCeId, hwPortGroupPolicyPeerAddress, hwPortGroupPolicyVcOrSiteId,hwPortGroupPolicyVlanIndex, hwPortGroupPolicyVsiName } ::= { hwL2mcPortGroupPolicyCfgTable 1 } HWL2mcPortGroupPolicyCfgEntry ::= SEQUENCE { hwPortGroupPolicyPortType HWPortType, hwPortGroupPolicyPortIfIndex InterfaceIndexOrZero, hwPortGroupPolicyPortPeId VlanIdOrAny, hwPortGroupPolicyPortCeId VlanIdOrAny, hwPortGroupPolicyPeerAddress IpAddress, hwPortGroupPolicyVcOrSiteId Unsigned32, hwPortGroupPolicyVlanIndex VlanIdOrAny, hwPortGroupPolicyVsiName DisplayString, hwPortGroupPolicyAclNum Integer32, hwPortGroupPolicyIgmpVersion INTEGER, hwPortGroupPolicyRowStatus RowStatus } hwPortGroupPolicyPortType OBJECT-TYPE SYNTAX HWPortType MAX-ACCESS not-accessible STATUS current DESCRIPTION "The interface type: 1: Invalid 2: PW interface 3: L2 interface 4: Encapsulation sub-interface 5: Termination sub-interface 6: Interface Board 7: Vlanif Port 9: batch config qinq port ce VLAN ID 10: batch config dot1q termination port ce VLAN ID " ::= { hwL2mcPortGroupPolicyCfgEntry 1 } hwPortGroupPolicyPortIfIndex OBJECT-TYPE SYNTAX InterfaceIndexOrZero MAX-ACCESS not-accessible STATUS current DESCRIPTION "The interface index. The value 0 indicates that the interface index is invalid." ::= { hwL2mcPortGroupPolicyCfgEntry 2 } hwPortGroupPolicyPortPeId OBJECT-TYPE SYNTAX VlanIdOrAny MAX-ACCESS not-accessible STATUS current DESCRIPTION "The PE VID of an interface. The value ranges from 1 to 4095. The value 4095 indicates that the PE VID is invalid. " ::= { hwL2mcPortGroupPolicyCfgEntry 3 } hwPortGroupPolicyPortCeId OBJECT-TYPE SYNTAX VlanIdOrAny MAX-ACCESS not-accessible STATUS current DESCRIPTION "The CE VID of an interface. The value ranges from 1 to 4095. The value 4095 indicates that the PE VID is invalid. " ::= { hwL2mcPortGroupPolicyCfgEntry 4 } hwPortGroupPolicyPeerAddress OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS not-accessible STATUS current DESCRIPTION "The peer IP address of a PW interface. The value 0.0.0.0 indicates that the IP address is invalid." ::= { hwL2mcPortGroupPolicyCfgEntry 5 } hwPortGroupPolicyVcOrSiteId OBJECT-TYPE SYNTAX Unsigned32(1..4294967295) MAX-ACCESS not-accessible STATUS current DESCRIPTION "The VC ID or SITE ID of a PW interface." ::= { hwL2mcPortGroupPolicyCfgEntry 6 } hwPortGroupPolicyVlanIndex OBJECT-TYPE SYNTAX VlanIdOrAny MAX-ACCESS not-accessible STATUS current DESCRIPTION "The VLAN ID, which is the configuration index in a VLAN. If a VSI is specified, the value is 4095. The value ranges from 1 to 4095. " ::= { hwL2mcPortGroupPolicyCfgEntry 7 } hwPortGroupPolicyVsiName OBJECT-TYPE SYNTAX DisplayString(SIZE (0..31)) MAX-ACCESS not-accessible STATUS current DESCRIPTION "The name of a VSI. If a VLAN is specified, the value is 32." ::= { hwL2mcPortGroupPolicyCfgEntry 8 } hwPortGroupPolicyAclNum OBJECT-TYPE SYNTAX Integer32(0|2000..3999) MAX-ACCESS read-create STATUS current DESCRIPTION "The number of a basic ACL. The ACL number ranges from 2000 to 3999. The default value is 0, indicating that the value is invalid. " ::= { hwL2mcPortGroupPolicyCfgEntry 9 } hwPortGroupPolicyIgmpVersion OBJECT-TYPE SYNTAX INTEGER { version1(1), version2(2), version3(3), versionAll(4) } MAX-ACCESS read-create STATUS current DESCRIPTION "The IGMP version. The value ranges from 1 to 4. The default is 4, indicating that no version is specified. " ::= { hwL2mcPortGroupPolicyCfgEntry 10 } hwPortGroupPolicyRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "The row status." ::= { hwL2mcPortGroupPolicyCfgEntry 100 } -- -- The hwL2mcChnlCfgInfo group. -- hwL2mcChnlCfgInfo OBJECT IDENTIFIER ::= { hwIgspMibObject 9 } hwL2mcChnlCfgTable OBJECT-TYPE SYNTAX SEQUENCE OF HWL2mcChnlCfgEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table describes the configurations of a channel." ::= { hwL2mcChnlCfgInfo 1 } hwL2mcChnlCfgEntry OBJECT-TYPE SYNTAX HWL2mcChnlCfgEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry of channel is created for each VLAN or VSI in the device create an channel." INDEX { hwChnlCfgVlanIndex, hwChnlCfgVsiName, hwChnlCfgChnlName } ::= { hwL2mcChnlCfgTable 1 } HWL2mcChnlCfgEntry ::= SEQUENCE { hwChnlCfgVlanIndex VlanIdOrAny, hwChnlCfgVsiName DisplayString, hwChnlCfgChnlName DisplayString, hwChnlCfgChnlType INTEGER, hwChnlCfgRowStatus RowStatus } hwChnlCfgVlanIndex OBJECT-TYPE SYNTAX VlanIdOrAny MAX-ACCESS not-accessible STATUS current DESCRIPTION "The VLAN ID, which is the configuration index in a VLAN. If a VSI is specified, the value is 4095. If both hwChnlCfgVlanIndex and hwChnlCfgVSIName are invalid, the configuration is global. The value ranges from 1 to 4095. " ::= { hwL2mcChnlCfgEntry 1 } hwChnlCfgVsiName OBJECT-TYPE SYNTAX DisplayString(SIZE (0..31)) MAX-ACCESS not-accessible STATUS current DESCRIPTION "The name of a VSI. If a VLAN is specified, the value is 32. If both hwChnlCfgVlanIndex and hwChnlCfgVSIName are invalid, the configuration is global." ::= { hwL2mcChnlCfgEntry 2 } hwChnlCfgChnlName OBJECT-TYPE SYNTAX DisplayString(SIZE (0..31)) MAX-ACCESS not-accessible STATUS current DESCRIPTION "The channel name." ::= { hwL2mcChnlCfgEntry 3 } hwChnlCfgChnlType OBJECT-TYPE SYNTAX INTEGER { ssm(1), asm(2) } MAX-ACCESS read-create STATUS current DESCRIPTION "The channel type: 1: SSM 2: ASM " ::= { hwL2mcChnlCfgEntry 9 } hwChnlCfgRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "The row status." ::= { hwL2mcChnlCfgEntry 100 } -- -- The hwL2mcLimitInfo group. -- hwL2mcLimitInfo OBJECT IDENTIFIER ::= { hwIgspMibObject 10 } hwL2mcLimitTable OBJECT-TYPE SYNTAX SEQUENCE OF HWL2mcLimitEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table describes the configurations of IGMP snooping CAC in a VLAN or a VSI." ::= { hwL2mcLimitInfo 1 } hwL2mcLimitEntry OBJECT-TYPE SYNTAX HWL2mcLimitEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry is created for each IGMP snooping CAC in a VLAN or a VSI." INDEX { hwL2mcLimitVlanIndex, hwL2mcLimitVsiName, hwL2mcLimitChnlName } ::= { hwL2mcLimitTable 1 } HWL2mcLimitEntry ::= SEQUENCE { hwL2mcLimitVlanIndex VlanIdOrAny, hwL2mcLimitVsiName DisplayString, hwL2mcLimitChnlName DisplayString, hwL2mcLimitMaxEntry Integer32, hwL2mcLimitEntryCnt Counter32, hwL2mcLimitMaxBandWidth Integer32, hwL2mcLimitBandWidth Counter32, hwL2mcLimitAcl Integer32, hwL2mcLimitCfgRowStatus RowStatus } hwL2mcLimitVlanIndex OBJECT-TYPE SYNTAX VlanIdOrAny MAX-ACCESS not-accessible STATUS current DESCRIPTION "The VLAN ID, which is the configuration index in a VLAN. If a VSI is specified, the value is 4095. If both hwVlanLimitVlanIndex and hwVlanLimitVSIName are invalid, the configuration is global. The value ranges from 1 to 4095. " ::= { hwL2mcLimitEntry 1 } hwL2mcLimitVsiName OBJECT-TYPE SYNTAX DisplayString(SIZE (0..31)) MAX-ACCESS not-accessible STATUS current DESCRIPTION "The name of a VSI. If a VLAN is specified, the value is 32. If both hwVlanLimitVlanIndex and hwVlanLimitVSIName are invalid, the configuration is global." ::= { hwL2mcLimitEntry 2 } hwL2mcLimitChnlName OBJECT-TYPE SYNTAX DisplayString(SIZE (0..31)) MAX-ACCESS not-accessible STATUS current DESCRIPTION "The channel name." ::= { hwL2mcLimitEntry 3 } hwL2mcLimitMaxEntry OBJECT-TYPE SYNTAX Integer32(0..16384) MAX-ACCESS read-create STATUS current DESCRIPTION "The maximum number of forwarding entries. The value 0 indicates that the number is invalid." ::= { hwL2mcLimitEntry 4 } hwL2mcLimitEntryCnt OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of current forwarding entries." ::= { hwL2mcLimitEntry 5 } hwL2mcLimitMaxBandWidth OBJECT-TYPE SYNTAX Integer32(0..4194304) MAX-ACCESS read-create STATUS current DESCRIPTION "The maximum bandwidth. The value 0 indicates that the bandwidth is invalid." ::= { hwL2mcLimitEntry 6 } hwL2mcLimitBandWidth OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The current bandwidth." ::= { hwL2mcLimitEntry 7 } hwL2mcLimitAcl OBJECT-TYPE SYNTAX Integer32(0|2000..3999) MAX-ACCESS read-create STATUS current DESCRIPTION "The number of ACL for the multicast groups that do not need to be configured with CAC limit. The ACL number ranges from 2000 to 3999. The default value is 0, indicating that the number is invalid. " ::= { hwL2mcLimitEntry 8 } hwL2mcLimitCfgRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "The row status." ::= { hwL2mcLimitEntry 100 } -- -- The hwL2mcPortLimitInfo group. -- hwL2mcPortLimitInfo OBJECT IDENTIFIER ::= { hwIgspMibObject 11 } hwL2mcPortLimitTable OBJECT-TYPE SYNTAX SEQUENCE OF HWL2mcPortLimitEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table describes the configurations of IGMP snooping CAC on an interface." ::= { hwL2mcPortLimitInfo 1 } hwL2mcPortLimitEntry OBJECT-TYPE SYNTAX HWL2mcPortLimitEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry is created for each IGMP snooping CAC on an interface." INDEX { hwPortLimitVlanIndex, hwPortLimitVsiName, hwPortLimitPortType, hwPortLimitIfIndex, hwPortLimitPeId, hwPortLimitCeId, hwPortLimitPeerAddress, hwPortLimitVcOrSiteId, hwPortLimitChnlName } ::= { hwL2mcPortLimitTable 1 } HWL2mcPortLimitEntry ::= SEQUENCE { hwPortLimitVlanIndex VlanIdOrAny, hwPortLimitVsiName DisplayString, hwPortLimitPortType HWPortType, hwPortLimitIfIndex InterfaceIndexOrZero, hwPortLimitPeId VlanIdOrAny, hwPortLimitCeId VlanIdOrAny, hwPortLimitPeerAddress IpAddress, hwPortLimitVcOrSiteId Unsigned32, hwPortLimitChnlName DisplayString, hwPortLimitAcl Integer32, hwPortLimitMaxEntry Integer32, hwPortLimitEntryCnt Counter32, hwPortLimitMaxBandWidth Integer32, hwPortLimitBandWidth Counter32, hwPortLimitCfgRowStatus RowStatus } hwPortLimitVlanIndex OBJECT-TYPE SYNTAX VlanIdOrAny MAX-ACCESS not-accessible STATUS current DESCRIPTION "The VLAN ID, which is the configuration index in a VLAN. If a VSI is specified, the value is 4095. The value ranges from 1 to 4095. " ::= { hwL2mcPortLimitEntry 1 } hwPortLimitVsiName OBJECT-TYPE SYNTAX DisplayString(SIZE (0..31)) MAX-ACCESS not-accessible STATUS current DESCRIPTION "The name of a VSI. If a VLAN is specified, the value is 32." ::= { hwL2mcPortLimitEntry 2 } hwPortLimitPortType OBJECT-TYPE SYNTAX HWPortType MAX-ACCESS not-accessible STATUS current DESCRIPTION "The interface type: 1: Invalid 2: PW interface 3: L2 interface 4: Encapsulation sub-interface 5: Termination sub-interface 9: batch config qinq port ce VLAN ID 10: batch config dot1q termination port ce VLAN ID " ::= { hwL2mcPortLimitEntry 3 } hwPortLimitIfIndex OBJECT-TYPE SYNTAX InterfaceIndexOrZero MAX-ACCESS not-accessible STATUS current DESCRIPTION "The interface index. The value 0 indicates that the interface index is invalid." ::= { hwL2mcPortLimitEntry 4 } hwPortLimitPeId OBJECT-TYPE SYNTAX VlanIdOrAny MAX-ACCESS not-accessible STATUS current DESCRIPTION "The PE VID of an interface. The value ranges from 1 to 4095. The value 4095 indicates that the PE VID is invalid. " ::= { hwL2mcPortLimitEntry 5 } hwPortLimitCeId OBJECT-TYPE SYNTAX VlanIdOrAny MAX-ACCESS not-accessible STATUS current DESCRIPTION "The CE VID of an interface. The value ranges from 1 to 4095. The value 4095 indicates that the PE VID is invalid. " ::= { hwL2mcPortLimitEntry 6 } hwPortLimitPeerAddress OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS not-accessible STATUS current DESCRIPTION "The peer IP address of a PW interface. The value 0.0.0.0 indicates that the IP address is invalid." ::= { hwL2mcPortLimitEntry 7 } hwPortLimitVcOrSiteId OBJECT-TYPE SYNTAX Unsigned32(1..4294967295) MAX-ACCESS not-accessible STATUS current DESCRIPTION "The VC ID or SITE ID of a PW interface." ::= { hwL2mcPortLimitEntry 8 } hwPortLimitChnlName OBJECT-TYPE SYNTAX DisplayString(SIZE (0..31)) MAX-ACCESS not-accessible STATUS current DESCRIPTION "The channel name." ::= { hwL2mcPortLimitEntry 9 } hwPortLimitAcl OBJECT-TYPE SYNTAX Integer32(0|2000..3999) MAX-ACCESS read-create STATUS current DESCRIPTION "The number of ACL for the multicast groups that do not need to be configured with CAC limit. The ACL number ranges from 2000 to 3999. The default value is 0, indicating that the number is invalid. " ::= { hwL2mcPortLimitEntry 10 } hwPortLimitMaxEntry OBJECT-TYPE SYNTAX Integer32(0..16384) MAX-ACCESS read-create STATUS current DESCRIPTION "The maximum number of forwarding entries. The value 0 indicates that the number is invalid." ::= { hwL2mcPortLimitEntry 11 } hwPortLimitEntryCnt OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of current forwarding entries." ::= { hwL2mcPortLimitEntry 12 } hwPortLimitMaxBandWidth OBJECT-TYPE SYNTAX Integer32(0..4194304) MAX-ACCESS read-create STATUS current DESCRIPTION "The maximum bandwidth. The value 0 indicates that the bandwidth is invalid." ::= { hwL2mcPortLimitEntry 13 } hwPortLimitBandWidth OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The current bandwidth." ::= { hwL2mcPortLimitEntry 14 } hwPortLimitCfgRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "The row status." ::= { hwL2mcPortLimitEntry 100 } -- -- The hwL2mcFastChnlCfgInfo group. -- hwL2mcFastChnlCfgInfo OBJECT IDENTIFIER ::= { hwIgspMibObject 12 } hwL2mcFastChnlCfgTable OBJECT-TYPE SYNTAX SEQUENCE OF HWL2mcFastChnlCfgEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Table contains l2 multicast fast forward information for IGMP Snooping." ::= { hwL2mcFastChnlCfgInfo 1 } hwL2mcFastChnlCfgEntry OBJECT-TYPE SYNTAX HWL2mcFastChnlCfgEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry is created for each IGMP snooping fast channel." INDEX { hwL2mcFastChnlCfgVlanIndex, hwL2mcFastChnlCfgVsiName, hwL2mcFastChnlCfgGroupAddress, hwL2mcFastChnlCfgGroupLen, hwL2mcFastChnlCfgSourceAddress, hwL2mcFastChnlCfgSourceLen } ::= { hwL2mcFastChnlCfgTable 1 } HWL2mcFastChnlCfgEntry ::= SEQUENCE { hwL2mcFastChnlCfgVlanIndex VlanIdOrAny, hwL2mcFastChnlCfgVsiName DisplayString, hwL2mcFastChnlCfgGroupAddress IpAddress, hwL2mcFastChnlCfgGroupLen Integer32, hwL2mcFastChnlCfgSourceAddress IpAddress , hwL2mcFastChnlCfgSourceLen Integer32 , hwL2mcFastChnlCfgRowStatus RowStatus } hwL2mcFastChnlCfgVlanIndex OBJECT-TYPE SYNTAX VlanIdOrAny MAX-ACCESS not-accessible STATUS current DESCRIPTION "The VLAN ID, which is the configuration index in a VLAN. If a VSI is specified, the value is 4095. The value ranges from 1 to 4095. " ::= { hwL2mcFastChnlCfgEntry 1 } hwL2mcFastChnlCfgVsiName OBJECT-TYPE SYNTAX DisplayString(SIZE (0..31)) MAX-ACCESS not-accessible STATUS current DESCRIPTION "The name of a VSI. If a VLAN is specified, the value is 32." ::= { hwL2mcFastChnlCfgEntry 2 } hwL2mcFastChnlCfgGroupAddress OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS not-accessible STATUS current DESCRIPTION "The group address of a multicast group. In the case of MAC forwarding, the group address is the smallest of 32 IP addresses." ::= { hwL2mcFastChnlCfgEntry 3 } hwL2mcFastChnlCfgGroupLen OBJECT-TYPE SYNTAX Integer32(16..32) MAX-ACCESS not-accessible STATUS current DESCRIPTION "The mask length of a multicast group address." ::= { hwL2mcFastChnlCfgEntry 4 } hwL2mcFastChnlCfgSourceAddress OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS not-accessible STATUS current DESCRIPTION "The source IP address of a multicast group." ::= { hwL2mcFastChnlCfgEntry 5 } hwL2mcFastChnlCfgSourceLen OBJECT-TYPE SYNTAX Integer32(0|16..32) MAX-ACCESS not-accessible STATUS current DESCRIPTION "The mask length of a multicast source address." ::= { hwL2mcFastChnlCfgEntry 6 } hwL2mcFastChnlCfgRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "The row status." ::= { hwL2mcFastChnlCfgEntry 100 } -- -- The hwL2mcRouterPortInfo group. -- hwL2mcRouterPortInfo OBJECT IDENTIFIER ::= { hwIgspMibObject 13 } hwL2mcRouterPortInfoTable OBJECT-TYPE SYNTAX SEQUENCE OF HWL2mcRouterPortInfoEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Table contains l2 multicast router port information for IGMP Snooping." ::= { hwL2mcRouterPortInfo 1 } hwL2mcRouterPortInfoEntry OBJECT-TYPE SYNTAX HWL2mcRouterPortInfoEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry is created for each IGMP snooping router port on an interface." INDEX { hwL2mcRouterPortVlanIndex, hwL2mcRouterPortVsiName, hwL2mcRouterPortType, hwL2mcRouterPortIfIndex, hwL2mcRouterPortPeId, hwL2mcRouterPortCeId, hwL2mcRouterPortPeerAddress, hwL2mcRouterPortVcOrSiteId } ::= { hwL2mcRouterPortInfoTable 1 } HWL2mcRouterPortInfoEntry ::= SEQUENCE { hwL2mcRouterPortVlanIndex VlanIdOrAny, hwL2mcRouterPortVsiName DisplayString, hwL2mcRouterPortType HWPortType , hwL2mcRouterPortIfIndex InterfaceIndexOrZero , hwL2mcRouterPortPeId VlanIdOrAny, hwL2mcRouterPortCeId VlanIdOrAny, hwL2mcRouterPortPeerAddress IpAddress, hwL2mcRouterPortVcOrSiteId Unsigned32, hwL2mcRouterPortGroupUpTime Counter32, hwL2mcRouterPortGroupExpires Counter32, hwL2mcRouterPortGroupHostFlag1 INTEGER } hwL2mcRouterPortVlanIndex OBJECT-TYPE SYNTAX VlanIdOrAny MAX-ACCESS not-accessible STATUS current DESCRIPTION "The VLAN ID, which is the configuration index in a VLAN. If a VSI is specified, the value is 4095. The value ranges from 1 to 4095. " ::= { hwL2mcRouterPortInfoEntry 1 } hwL2mcRouterPortVsiName OBJECT-TYPE SYNTAX DisplayString(SIZE (0..31)) MAX-ACCESS not-accessible STATUS current DESCRIPTION "The name of a VSI. If a VLAN is specified, the value is 32." ::= { hwL2mcRouterPortInfoEntry 2 } hwL2mcRouterPortType OBJECT-TYPE SYNTAX HWPortType MAX-ACCESS not-accessible STATUS current DESCRIPTION "The interface type: 1: Invalid 2: PW interface 3: L2 interface 4: Encapsulation sub-interface 5: Termination sub-interface 6: Interface Board 7: Vlanif Port " ::= { hwL2mcRouterPortInfoEntry 3 } hwL2mcRouterPortIfIndex OBJECT-TYPE SYNTAX InterfaceIndexOrZero MAX-ACCESS not-accessible STATUS current DESCRIPTION "The interface index. The value 0 indicates that the interface index is invalid." ::= { hwL2mcRouterPortInfoEntry 4 } hwL2mcRouterPortPeId OBJECT-TYPE SYNTAX VlanIdOrAny MAX-ACCESS not-accessible STATUS current DESCRIPTION "The PE VID of an interface. The value ranges from 1 to 4095. The value 4095 indicates that the PE VID is invalid. " ::= { hwL2mcRouterPortInfoEntry 5 } hwL2mcRouterPortCeId OBJECT-TYPE SYNTAX VlanIdOrAny MAX-ACCESS not-accessible STATUS current DESCRIPTION "The CE VID of an interface. The value ranges from 1 to 4095. The value 4095 indicates that the PE VID is invalid. " ::= { hwL2mcRouterPortInfoEntry 6 } hwL2mcRouterPortPeerAddress OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS not-accessible STATUS current DESCRIPTION "The peer IP address of a PW interface. The value 0.0.0.0 indicates that the IP address is invalid." ::= { hwL2mcRouterPortInfoEntry 7 } hwL2mcRouterPortVcOrSiteId OBJECT-TYPE SYNTAX Unsigned32(1..4294967295) MAX-ACCESS not-accessible STATUS current DESCRIPTION "The VC ID or SITE ID of a PW interface." ::= { hwL2mcRouterPortInfoEntry 8 } hwL2mcRouterPortGroupUpTime OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "How long the group exists in the forwarding entry." ::= { hwL2mcRouterPortInfoEntry 16 } hwL2mcRouterPortGroupExpires OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The timeout period of the router port, that is, the aging time of the router port." ::= { hwL2mcRouterPortInfoEntry 17 } hwL2mcRouterPortGroupHostFlag1 OBJECT-TYPE SYNTAX INTEGER { static(1), dynamic(2), staticDynamic(3) } MAX-ACCESS read-only STATUS current DESCRIPTION "The mode to create an interface on the host: 1: static 2: dynamic 3: static and dynamic " ::= { hwL2mcRouterPortInfoEntry 19 } -- -- -- The hwL2mcRouterPortCfgInfo group. -- hwL2mcRouterPortCfgInfo OBJECT IDENTIFIER ::= { hwIgspMibObject 14 } hwL2mcRouterPortCfgTable OBJECT-TYPE SYNTAX SEQUENCE OF HWL2mcRouterPortCfgEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Table contains l2 multicast configuration of router port for IGMP Snooping." ::= { hwL2mcRouterPortCfgInfo 1 } hwL2mcRouterPortCfgEntry OBJECT-TYPE SYNTAX HWL2mcRouterPortCfgEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry is created for each IGMP snooping static router port on an interface." INDEX { hwL2mcRouterPortCfgPortType, hwL2mcRouterPortCfgPortIfIndex, hwL2mcRouterPortCfgPortPeId , hwL2mcRouterPortCfgPortCeId , hwL2mcRouterPortCfgPeerAddress , hwL2mcRouterPortCfgVcOrSiteId, hwL2mcRouterPortCfgVlanIndex, hwL2mcRouterPortCfgVsiName } ::= { hwL2mcRouterPortCfgTable 1 } HWL2mcRouterPortCfgEntry ::= SEQUENCE { hwL2mcRouterPortCfgPortType HWPortType , hwL2mcRouterPortCfgPortIfIndex InterfaceIndexOrZero , hwL2mcRouterPortCfgPortPeId VlanIdOrAny, hwL2mcRouterPortCfgPortCeId VlanIdOrAny, hwL2mcRouterPortCfgPeerAddress IpAddress, hwL2mcRouterPortCfgVcOrSiteId Unsigned32, hwL2mcRouterPortCfgVlanIndex VlanIdOrAny, hwL2mcRouterPortCfgVsiName DisplayString, hwL2mcRouterPortCfgRowStatus RowStatus } hwL2mcRouterPortCfgPortType OBJECT-TYPE SYNTAX HWPortType MAX-ACCESS not-accessible STATUS current DESCRIPTION "The interface type: 1: Invalid 2: PW interface 3: L2 interface 4: Encapsulation sub-interface 5: Termination sub-interface 6: Interface Board 7: Vlanif Port " ::= { hwL2mcRouterPortCfgEntry 1 } hwL2mcRouterPortCfgPortIfIndex OBJECT-TYPE SYNTAX InterfaceIndexOrZero MAX-ACCESS not-accessible STATUS current DESCRIPTION "The interface index. The value 0 indicates that the interface index is invalid." ::= { hwL2mcRouterPortCfgEntry 2 } hwL2mcRouterPortCfgPortPeId OBJECT-TYPE SYNTAX VlanIdOrAny MAX-ACCESS not-accessible STATUS current DESCRIPTION "The PE VID of an interface. The value ranges from 1 to 4095. The value 4095 indicates that the PE VID is invalid. " ::= { hwL2mcRouterPortCfgEntry 3 } hwL2mcRouterPortCfgPortCeId OBJECT-TYPE SYNTAX VlanIdOrAny MAX-ACCESS not-accessible STATUS current DESCRIPTION "The CE VID of an interface. The value ranges from 1 to 4095. The value 4095 indicates that the PE VID is invalid. " ::= { hwL2mcRouterPortCfgEntry 4 } hwL2mcRouterPortCfgPeerAddress OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS not-accessible STATUS current DESCRIPTION "The peer IP address of a PW interface. The value 0.0.0.0 indicates that the IP address is invalid." ::= { hwL2mcRouterPortCfgEntry 5 } hwL2mcRouterPortCfgVcOrSiteId OBJECT-TYPE SYNTAX Unsigned32(1..4294967295) MAX-ACCESS not-accessible STATUS current DESCRIPTION "The VC ID or SITE ID of a PW interface." ::= { hwL2mcRouterPortCfgEntry 6 } hwL2mcRouterPortCfgVlanIndex OBJECT-TYPE SYNTAX VlanIdOrAny MAX-ACCESS not-accessible STATUS current DESCRIPTION "The VLAN ID, which is the configuration index in a VLAN. If a VSI is specified, the value is 4095. The value ranges from 1 to 4095. " ::= { hwL2mcRouterPortCfgEntry 7 } hwL2mcRouterPortCfgVsiName OBJECT-TYPE SYNTAX DisplayString(SIZE (0..31)) MAX-ACCESS not-accessible STATUS current DESCRIPTION "The name of a VSI. If a VLAN is specified, the value is 32." ::= { hwL2mcRouterPortCfgEntry 8 } hwL2mcRouterPortCfgRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "The row status." ::= { hwL2mcRouterPortCfgEntry 100 } -- -- The hwL2mcChnlGroupCfgInfo group. -- hwL2mcChnlGroupCfgInfo OBJECT IDENTIFIER ::= { hwIgspMibObject 15 } hwL2mcChnlGroupCfgTable OBJECT-TYPE SYNTAX SEQUENCE OF HWL2mcChnlGroupCfgEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table describes the group configurations of a channel." ::= { hwL2mcChnlGroupCfgInfo 1 } hwL2mcChnlGroupCfgEntry OBJECT-TYPE SYNTAX HWL2mcChnlGroupCfgEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry of channel is created for each VLAN or VSI in the device create an channel." INDEX { hwChnlGroupCfgVlanIndex , hwChnlGroupCfgVsiName , hwChnlCfgGroupChnlName, hwChnlGroupCfgGroupAddress , hwChnlGroupCfgGroupLen, hwChnlGroupCfgSourceAddress , hwChnlGroupCfgSourceLen } ::= { hwL2mcChnlGroupCfgTable 1 } HWL2mcChnlGroupCfgEntry ::= SEQUENCE { hwChnlGroupCfgVlanIndex VlanIdOrAny, hwChnlGroupCfgVsiName DisplayString, hwChnlCfgGroupChnlName DisplayString, hwChnlGroupCfgGroupAddress IpAddress, hwChnlGroupCfgGroupLen Integer32, hwChnlGroupCfgSourceAddress IpAddress, hwChnlGroupCfgSourceLen Integer32, hwChnlGroupCfgPerBand Integer32, hwChnlGroupCfgRowStatus RowStatus } hwChnlGroupCfgVlanIndex OBJECT-TYPE SYNTAX VlanIdOrAny MAX-ACCESS not-accessible STATUS current DESCRIPTION "The VLAN ID, which is the configuration index in a VLAN. If a VSI is specified, the value is 4095. If both hwChnlCfgVlanIndex and hwChnlCfgVSIName are invalid, the configuration is global. The value ranges from 1 to 4095. " ::= { hwL2mcChnlGroupCfgEntry 1 } hwChnlGroupCfgVsiName OBJECT-TYPE SYNTAX DisplayString(SIZE (0..31)) MAX-ACCESS not-accessible STATUS current DESCRIPTION "The name of a VSI. If a VLAN is specified, the value is 32. If both hwChnlCfgVlanIndex and hwChnlCfgVSIName are invalid, the configuration is global." ::= { hwL2mcChnlGroupCfgEntry 2 } hwChnlCfgGroupChnlName OBJECT-TYPE SYNTAX DisplayString(SIZE (0..31)) MAX-ACCESS not-accessible STATUS current DESCRIPTION "The channel name." ::= { hwL2mcChnlGroupCfgEntry 3 } hwChnlGroupCfgGroupAddress OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS not-accessible STATUS current DESCRIPTION "The group address of a multicast group. In the case of MAC forwarding, the group address is the smallest of 32 IP addresses." ::= { hwL2mcChnlGroupCfgEntry 4 } hwChnlGroupCfgGroupLen OBJECT-TYPE SYNTAX Integer32(4..32) MAX-ACCESS not-accessible STATUS current DESCRIPTION "The mask length of a multicast group." ::= { hwL2mcChnlGroupCfgEntry 5 } hwChnlGroupCfgSourceAddress OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS not-accessible STATUS current DESCRIPTION "The source IP address of a multicast group." ::= { hwL2mcChnlGroupCfgEntry 6 } hwChnlGroupCfgSourceLen OBJECT-TYPE SYNTAX Integer32(0|8..32) MAX-ACCESS not-accessible STATUS current DESCRIPTION "The mask length of a multicast source address." ::= { hwL2mcChnlGroupCfgEntry 7 } hwChnlGroupCfgPerBand OBJECT-TYPE SYNTAX Integer32(0..131072) MAX-ACCESS read-create STATUS current DESCRIPTION "The bandwidth of a multicast group." ::= { hwL2mcChnlGroupCfgEntry 9 } hwChnlGroupCfgRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "The row status." ::= { hwL2mcChnlGroupCfgEntry 100 } -- -- The hwL2mcGroupPolicyCfgInfo group. -- hwL2mcGroupPolicyCfgInfo OBJECT IDENTIFIER ::= { hwIgspMibObject 16 } hwL2mcGroupPolicyCfgTable OBJECT-TYPE SYNTAX SEQUENCE OF HWL2mcGroupPolicyCfgEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "In this table, you can query or configure a group policy to filter entries on a port." ::= { hwL2mcGroupPolicyCfgInfo 1 } hwL2mcGroupPolicyCfgEntry OBJECT-TYPE SYNTAX HWL2mcGroupPolicyCfgEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry is created for each active VLAN or VSI in the device when a group policy added." INDEX { hwGroupPolicyVlanIndex, hwGroupPolicyVsiName } ::= { hwL2mcGroupPolicyCfgTable 1 } HWL2mcGroupPolicyCfgEntry ::= SEQUENCE { hwGroupPolicyVlanIndex VlanIdOrAny, hwGroupPolicyVsiName DisplayString, hwGroupPolicyAclNum Integer32, hwGroupPolicyIgmpVersion INTEGER, hwGroupPolicyRowStatus RowStatus } hwGroupPolicyVlanIndex OBJECT-TYPE SYNTAX VlanIdOrAny MAX-ACCESS not-accessible STATUS current DESCRIPTION "The VLAN ID, which is the configuration index in a VLAN. If a VSI is specified, the value is 4095. The value ranges from 1 to 4095. " ::= { hwL2mcGroupPolicyCfgEntry 1 } hwGroupPolicyVsiName OBJECT-TYPE SYNTAX DisplayString(SIZE (0..31)) MAX-ACCESS not-accessible STATUS current DESCRIPTION "The name of a VSI. If a VLAN is specified, the value is 32." ::= { hwL2mcGroupPolicyCfgEntry 2 } hwGroupPolicyAclNum OBJECT-TYPE SYNTAX Integer32(0|2000..3999) MAX-ACCESS read-create STATUS current DESCRIPTION "The number of a basic ACL. The ACL number ranges from 2000 to 3999. The default value is 0, indicating that the value is invalid. " ::= { hwL2mcGroupPolicyCfgEntry 3 } hwGroupPolicyIgmpVersion OBJECT-TYPE SYNTAX INTEGER { version1(1), version2(2), version3(3), versionAll(4) } MAX-ACCESS read-create STATUS current DESCRIPTION "The IGMP version. The value ranges from 1 to 4. The default is 4, indicating that no version is specified. " ::= { hwL2mcGroupPolicyCfgEntry 4 } hwGroupPolicyRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "The row status." ::= { hwL2mcGroupPolicyCfgEntry 100 } -- -- The hwL2mcChnlDenyCfgInfo group. -- hwL2mcChnlDenyCfgInfo OBJECT IDENTIFIER ::= { hwIgspMibObject 17 } hwL2mcChnlDenyCfgTable OBJECT-TYPE SYNTAX SEQUENCE OF HWL2mcChnlDenyCfgEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table describes the configurations of deny unspecified group for each VLAN or VSI, or in global." ::= { hwL2mcChnlDenyCfgInfo 1 } hwL2mcChnlDenyCfgEntry OBJECT-TYPE SYNTAX HWL2mcChnlDenyCfgEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry of channel deny is created for each VLAN or VSI in the device create an channel." INDEX { hwChnlDenyCfgVlanIndex, hwChnlDenyCfgVsiName } ::= { hwL2mcChnlDenyCfgTable 1 } HWL2mcChnlDenyCfgEntry ::= SEQUENCE { hwChnlDenyCfgVlanIndex VlanIdOrAny, hwChnlDenyCfgVsiName DisplayString, hwChnlDenyCfg INTEGER, hwChnlDenyCfgRowStatus RowStatus } hwChnlDenyCfgVlanIndex OBJECT-TYPE SYNTAX VlanIdOrAny MAX-ACCESS not-accessible STATUS current DESCRIPTION "The VLAN ID, which is the configuration index in a VLAN. If a VSI is specified, the value is 4095. If both hwChnlCfgVlanIndex and hwChnlCfgVSIName are invalid, the configuration is global. The value ranges from 1 to 4095. " ::= { hwL2mcChnlDenyCfgEntry 1 } hwChnlDenyCfgVsiName OBJECT-TYPE SYNTAX DisplayString(SIZE (0..31)) MAX-ACCESS not-accessible STATUS current DESCRIPTION "The name of a VSI. If a VLAN is specified, the value is 32. If both hwChnlCfgVlanIndex and hwChnlCfgVSIName are invalid, the configuration is global." ::= { hwL2mcChnlDenyCfgEntry 2 } hwChnlDenyCfg OBJECT-TYPE SYNTAX INTEGER { forward(1), discard(2) } MAX-ACCESS read-create STATUS current DESCRIPTION "Whether discard unspecified channel: 1: not discard 2: discard " ::= { hwL2mcChnlDenyCfgEntry 3 } hwChnlDenyCfgRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "The row status." ::= { hwL2mcChnlDenyCfgEntry 100 } -- -- The hwL2mcQinQPortTable group. -- hwL2mcQinQPortInfo OBJECT IDENTIFIER ::= { hwIgspMibObject 18 } hwL2mcQinQPortTable OBJECT-TYPE SYNTAX SEQUENCE OF HWL2mcQinQPortEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table describes the specific port statistic of QinQ table of protol." ::= { hwL2mcQinQPortInfo 1 } hwL2mcQinQPortEntry OBJECT-TYPE SYNTAX HWL2mcQinQPortEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry of the specific port statistic of QinQ table of protol." INDEX { hwQinQPortVlanIndex, hwQinQPortVsiName, hwL2mcQinQPortIfIndex, hwQinQPortGroupAddr, hwQinQPortSourceAddr, hwQinQPortPe, hwQinQPortCe } ::= { hwL2mcQinQPortTable 1 } HWL2mcQinQPortEntry ::= SEQUENCE { hwQinQPortVlanIndex VlanIdOrAny, hwQinQPortVsiName DisplayString, hwL2mcQinQPortIfIndex InterfaceIndexOrZero, hwQinQPortGroupAddr IpAddress, hwQinQPortSourceAddr IpAddress, hwQinQPortPe VlanIdOrAny, hwQinQPortCe VlanIdOrAny, hwQinQPortTime Counter32, hwQinQPortFlag Integer32 } hwQinQPortVlanIndex OBJECT-TYPE SYNTAX VlanIdOrAny MAX-ACCESS not-accessible STATUS current DESCRIPTION "The VLAN ID, which is the configuration index in a VLAN. If a VSI is specified, the value is 4095. If both hwChnlCfgVlanIndex and hwChnlCfgVSIName are invalid, the configuration is global. The value ranges from 1 to 4095. " ::= { hwL2mcQinQPortEntry 1 } hwQinQPortVsiName OBJECT-TYPE SYNTAX DisplayString(SIZE (0..31)) MAX-ACCESS not-accessible STATUS current DESCRIPTION "The name of a VSI. If a VLAN is specified, the value is 32. If both hwChnlCfgVlanIndex and hwChnlCfgVSIName are invalid, the configuration is global." ::= { hwL2mcQinQPortEntry 2 } hwL2mcQinQPortIfIndex OBJECT-TYPE SYNTAX InterfaceIndexOrZero MAX-ACCESS not-accessible STATUS current DESCRIPTION "The interface index. The value 0 indicates that the interface index is invalid." ::= { hwL2mcQinQPortEntry 3 } hwQinQPortGroupAddr OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS not-accessible STATUS current DESCRIPTION "The group address of a multicast group. In the case of MAC forwarding, the group address is the smallest of 32 IP addresses." ::= { hwL2mcQinQPortEntry 4 } hwQinQPortSourceAddr OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS not-accessible STATUS current DESCRIPTION "The source IP address of a multicast group." ::= { hwL2mcQinQPortEntry 5 } hwQinQPortPe OBJECT-TYPE SYNTAX VlanIdOrAny MAX-ACCESS not-accessible STATUS current DESCRIPTION "The PE VID of an interface. The value ranges from 1 to 4095. The value 4095 indicates that the PE VID is invalid. " ::= { hwL2mcQinQPortEntry 6 } hwQinQPortCe OBJECT-TYPE SYNTAX VlanIdOrAny MAX-ACCESS not-accessible STATUS current DESCRIPTION "The CE VID of an interface. The value ranges from 1 to 4095. The value 4095 indicates that the CE VID is invalid. " ::= { hwL2mcQinQPortEntry 7 } hwQinQPortTime OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of QinQ Port entry live time in second." ::= { hwL2mcQinQPortEntry 20 } hwQinQPortFlag OBJECT-TYPE SYNTAX Integer32(1..4) MAX-ACCESS read-only STATUS current DESCRIPTION "The port flag: 1 static 2 dynamic 3 static and dynamic 4 invalid " ::= { hwL2mcQinQPortEntry 21 } -- -- The hwL2mcETrackingInfoTable group. -- hwL2mcETrackingInfoInfo OBJECT IDENTIFIER ::= { hwIgspMibObject 19 } hwL2mcETrackingInfoTable OBJECT-TYPE SYNTAX SEQUENCE OF HWL2mcETrackingInfoEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table describes the host explicit tracking." ::= { hwL2mcETrackingInfoInfo 1 } hwL2mcETrackingInfoEntry OBJECT-TYPE SYNTAX HWL2mcETrackingInfoEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry of the host explicit tracking." INDEX { hwETrackInfoSlotIndex, hwETrackInfoVlanIndex, hwETrackInfoVsiName, hwETrackInfoGroupAddr, hwETrackInfoSourceAddr, hwETrackInfoPortType, hwETrackInfoPortIfIndex, hwETrackInfoPortPeId, hwETrackInfoPortCeId, hwETrackInfoPeerAddress, hwETrackInfoVcOrSiteId,hwETrackInfoBoardNum, hwETrackInfoReportAddr } ::= { hwL2mcETrackingInfoTable 1 } HWL2mcETrackingInfoEntry ::= SEQUENCE { hwETrackInfoSlotIndex Integer32, hwETrackInfoVlanIndex VlanIdOrAny, hwETrackInfoVsiName DisplayString, hwETrackInfoGroupAddr IpAddress, hwETrackInfoSourceAddr IpAddress, hwETrackInfoPortType HWPortType, hwETrackInfoPortIfIndex InterfaceIndexOrZero, hwETrackInfoPortPeId VlanIdOrAny, hwETrackInfoPortCeId VlanIdOrAny, hwETrackInfoPeerAddress IpAddress, hwETrackInfoVcOrSiteId Unsigned32, hwETrackInfoBoardNum Integer32, hwETrackInfoReportAddr IpAddress, hwETrackInfoFlag Integer32 } hwETrackInfoSlotIndex OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS not-accessible STATUS current DESCRIPTION "The slot index, which is interface board number. " ::= { hwL2mcETrackingInfoEntry 1 } hwETrackInfoVlanIndex OBJECT-TYPE SYNTAX VlanIdOrAny MAX-ACCESS not-accessible STATUS current DESCRIPTION "The VLAN ID, which is the configuration index in a VLAN. If a VSI is specified, the value is 4095. If both hwETrackInfoVlanIndex and hwETrackInfoVsiName are invalid, the configuration is global. The value ranges from 1 to 4095. " ::= { hwL2mcETrackingInfoEntry 2 } hwETrackInfoVsiName OBJECT-TYPE SYNTAX DisplayString(SIZE (0..31)) MAX-ACCESS not-accessible STATUS current DESCRIPTION "The name of a VSI. If a VLAN is specified, the value is 32. If both hwETrackInfoVlanIndex and hwETrackInfoVsiName are invalid, the configuration is global." ::= { hwL2mcETrackingInfoEntry 3 } hwETrackInfoGroupAddr OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS not-accessible STATUS current DESCRIPTION "The group address of a multicast group. In the case of MAC forwarding, the group address is the smallest of 32 IP addresses." ::= { hwL2mcETrackingInfoEntry 4 } hwETrackInfoSourceAddr OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS not-accessible STATUS current DESCRIPTION "The source IP address of a multicast group." ::= { hwL2mcETrackingInfoEntry 5 } hwETrackInfoPortType OBJECT-TYPE SYNTAX HWPortType MAX-ACCESS not-accessible STATUS current DESCRIPTION "The interface type: 1: Invalid 2: PW interface 3: L2 interface 4: Encapsulation sub-interface 5: Termination sub-interface 6: Interface Board 7: Vlanif Port " ::= { hwL2mcETrackingInfoEntry 6 } hwETrackInfoPortIfIndex OBJECT-TYPE SYNTAX InterfaceIndexOrZero MAX-ACCESS not-accessible STATUS current DESCRIPTION "The interface index. The value 0 indicates that the interface index is invalid." ::= { hwL2mcETrackingInfoEntry 7 } hwETrackInfoPortPeId OBJECT-TYPE SYNTAX VlanIdOrAny MAX-ACCESS not-accessible STATUS current DESCRIPTION "The PE VID of an interface. The value ranges from 1 to 4095. The value 4095 indicates that the PE VID is invalid. " ::= { hwL2mcETrackingInfoEntry 8 } hwETrackInfoPortCeId OBJECT-TYPE SYNTAX VlanIdOrAny MAX-ACCESS not-accessible STATUS current DESCRIPTION "The CE VID of an interface. The value ranges from 1 to 4095. The value 4095 indicates that the CE VID is invalid. " ::= { hwL2mcETrackingInfoEntry 9 } hwETrackInfoPeerAddress OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS not-accessible STATUS current DESCRIPTION "The peer IP address of a PW interface. The value 0.0.0.0 indicates that the IP address is invalid." ::= { hwL2mcETrackingInfoEntry 10 } hwETrackInfoVcOrSiteId OBJECT-TYPE SYNTAX Unsigned32(1..4294967295) MAX-ACCESS not-accessible STATUS current DESCRIPTION "The VC ID or SITE ID of a PW interface." ::= { hwL2mcETrackingInfoEntry 11 } hwETrackInfoBoardNum OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS not-accessible STATUS current DESCRIPTION "The interface board number." ::= { hwL2mcETrackingInfoEntry 12 } hwETrackInfoReportAddr OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS not-accessible STATUS current DESCRIPTION "The source IP address of a user." ::= { hwL2mcETrackingInfoEntry 13 } hwETrackInfoFlag OBJECT-TYPE SYNTAX Integer32(1..4) MAX-ACCESS read-only STATUS current DESCRIPTION "The port filter mode: 1 include 2 exclude " ::= { hwL2mcETrackingInfoEntry 20 } -- -- The hwL2mcSourceGroupTable group. -- hwL2mcSourceGroupInfo OBJECT IDENTIFIER ::= { hwIgspMibObject 22 } hwL2mcSourceGroupTable OBJECT-TYPE SYNTAX SEQUENCE OF HWL2mcSourceGroupEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Table contains VLAN or VSI performance statistics information for IGMP Snooping." ::= { hwL2mcSourceGroupInfo 1 } hwL2mcSourceGroupEntry OBJECT-TYPE SYNTAX HWL2mcSourceGroupEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry is created for each active VLAN or VSI in the device and deleted when the VLAN or VSI becomes inactive." INDEX { hwL2mcSourceGroupVlanIndex, hwL2mcSourceGroupVsiName, hwL2mcSourceGroupGroupAddress, hwL2mcSourceGroupSourceAddress} ::= { hwL2mcSourceGroupTable 1 } HWL2mcSourceGroupEntry ::= SEQUENCE { hwL2mcSourceGroupVlanIndex VlanIdOrAny, hwL2mcSourceGroupVsiName DisplayString, hwL2mcSourceGroupGroupAddress IpAddress, hwL2mcSourceGroupSourceAddress IpAddress, hwL2mcSourceGroupStat Counter64 } hwL2mcSourceGroupVlanIndex OBJECT-TYPE SYNTAX VlanIdOrAny MAX-ACCESS not-accessible STATUS current DESCRIPTION "The VLAN ID, which is the configuration index in a VLAN. If a VSI is specified, the value is 4095. The value ranges from 1 to 4095. " ::= { hwL2mcSourceGroupEntry 1 } hwL2mcSourceGroupVsiName OBJECT-TYPE SYNTAX DisplayString(SIZE (0..31)) MAX-ACCESS not-accessible STATUS current DESCRIPTION "The name of a VSI. If a VLAN is specified, the value is 32." ::= { hwL2mcSourceGroupEntry 2 } hwL2mcSourceGroupGroupAddress OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS not-accessible STATUS current DESCRIPTION "The group address of a multicast group. In the case of MAC forwarding, the group address is the smallest of 32 IP addresses." ::= { hwL2mcSourceGroupEntry 3 } hwL2mcSourceGroupSourceAddress OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS not-accessible STATUS current DESCRIPTION "The source IP address of a multicast group." ::= { hwL2mcSourceGroupEntry 4 } hwL2mcSourceGroupStat OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "the packet statistic of (S,G) group." ::= { hwL2mcSourceGroupEntry 10 } -- -- The hwL2mcDTFwdInfo group. -- hwL2mcDTFwdInfo OBJECT IDENTIFIER ::= { hwIgspMibObject 23 } hwL2mcDTFwdTable OBJECT-TYPE SYNTAX SEQUENCE OF HWL2mcDTFwdEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Table contains l2 multicast forward information for IGMP Snooping." ::= { hwL2mcDTFwdInfo 1 } hwL2mcDTFwdEntry OBJECT-TYPE SYNTAX HWL2mcDTFwdEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry is created for each active VLAN or VSI in the device create a forwarding table entry and delete when a forwarding table entry deleted." INDEX { hwL2mcDTFwdSlotIndex, hwL2mcDTFwdVlanIndex, hwL2mcDTFwdVsiName, hwL2mcDTFwdGroupAddress, hwL2mcDTFwdSourceAddress, hwL2mcDTFwdPortType, hwL2mcDTFwdPortIfIndex, hwL2mcDTFwdPortPeId, hwL2mcDTFwdPortCeId, hwL2mcDTFwdPeerAddress, hwL2mcDTFwdVcOrSiteId, hwL2mcDTFwdBoardNum } ::= { hwL2mcDTFwdTable 1 } HWL2mcDTFwdEntry ::= SEQUENCE { hwL2mcDTFwdSlotIndex Integer32, hwL2mcDTFwdVlanIndex VlanIdOrAny, hwL2mcDTFwdVsiName DisplayString, hwL2mcDTFwdGroupAddress IpAddress, hwL2mcDTFwdSourceAddress IpAddress, hwL2mcDTFwdPortType HWPortType, hwL2mcDTFwdPortIfIndex InterfaceIndexOrZero, hwL2mcDTFwdPortPeId VlanIdOrAny, hwL2mcDTFwdPortCeId VlanIdOrAny, hwL2mcDTFwdPeerAddress IpAddress, hwL2mcDTFwdVcOrSiteId Unsigned32, hwL2mcDTFwdBoardNum Integer32, hwL2mcDTFwdAddressType INTEGER, hwL2mcDTFwdHostFlag1 INTEGER, hwL2mcDTFwdHostFlag2 INTEGER, hwL2mcDTFwdHostFlag3 INTEGER, hwL2mcDTFwdHostFlag4 INTEGER } hwL2mcDTFwdSlotIndex OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS not-accessible STATUS current DESCRIPTION "The slot index, which is interface board number. " ::= { hwL2mcDTFwdEntry 1 } hwL2mcDTFwdVlanIndex OBJECT-TYPE SYNTAX VlanIdOrAny MAX-ACCESS not-accessible STATUS current DESCRIPTION "The VLAN ID, which is the configuration index in a VLAN. If a VSI is specified, the value is 4095. The value ranges from 1 to 4095. " ::= { hwL2mcDTFwdEntry 2 } hwL2mcDTFwdVsiName OBJECT-TYPE SYNTAX DisplayString(SIZE (0..31)) MAX-ACCESS not-accessible STATUS current DESCRIPTION "The name of a VSI. If a VLAN is specified, the value is 32." ::= { hwL2mcDTFwdEntry 3 } hwL2mcDTFwdGroupAddress OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS not-accessible STATUS current DESCRIPTION "The group address of a multicast group. In the case of MAC forwarding, the group address is the smallest of 32 IP addresses." ::= { hwL2mcDTFwdEntry 4 } hwL2mcDTFwdSourceAddress OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS not-accessible STATUS current DESCRIPTION "The source IP address of a multicast group." ::= { hwL2mcDTFwdEntry 5 } hwL2mcDTFwdPortType OBJECT-TYPE SYNTAX HWPortType MAX-ACCESS not-accessible STATUS current DESCRIPTION "The interface type: 1: Invalid 2: PW interface 3: L2 interface 4: Encapsulation sub-interface 5: Termination sub-interface 6: Interface Board 7: Vlanif Port " ::= { hwL2mcDTFwdEntry 6 } hwL2mcDTFwdPortIfIndex OBJECT-TYPE SYNTAX InterfaceIndexOrZero MAX-ACCESS not-accessible STATUS current DESCRIPTION "The interface index. The value 0 indicates that the interface index is invalid." ::= { hwL2mcDTFwdEntry 7 } hwL2mcDTFwdPortPeId OBJECT-TYPE SYNTAX VlanIdOrAny MAX-ACCESS not-accessible STATUS current DESCRIPTION "The PE VID of an interface. The value ranges from 1 to 4095. The value 4095 indicates that the PE VID is invalid. " ::= { hwL2mcDTFwdEntry 8 } hwL2mcDTFwdPortCeId OBJECT-TYPE SYNTAX VlanIdOrAny MAX-ACCESS not-accessible STATUS current DESCRIPTION "The CE VID of an interface. The value ranges from 1 to 4095. The value 4095 indicates that the CE VID is invalid. " ::= { hwL2mcDTFwdEntry 9 } hwL2mcDTFwdPeerAddress OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS not-accessible STATUS current DESCRIPTION "The peer IP address of a PW interface. The value 0.0.0.0 indicates that the IP address is invalid." ::= { hwL2mcDTFwdEntry 10 } hwL2mcDTFwdVcOrSiteId OBJECT-TYPE SYNTAX Unsigned32(1..4294967295) MAX-ACCESS not-accessible STATUS current DESCRIPTION "The VC ID or SITE ID of a PW interface." ::= { hwL2mcDTFwdEntry 11 } hwL2mcDTFwdBoardNum OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS not-accessible STATUS current DESCRIPTION "The interface board number." ::= { hwL2mcDTFwdEntry 12 } hwL2mcDTFwdAddressType OBJECT-TYPE SYNTAX INTEGER { ip(1), mac(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "The address type of an entry: 1: IP 2: MAC The default value is 1. " ::= { hwL2mcDTFwdEntry 21 } hwL2mcDTFwdHostFlag1 OBJECT-TYPE SYNTAX INTEGER { static(1), dynamic(2), staticDynamic(3), invalid(4) } MAX-ACCESS read-only STATUS current DESCRIPTION "The mode to create an interface on the host: 1: static 2: dynamic 3: static and dynamic 4: invalid " ::= { hwL2mcDTFwdEntry 22 } hwL2mcDTFwdHostFlag2 OBJECT-TYPE SYNTAX INTEGER { nonMapping(1), mapping(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "Whether an interface on the host is created through SSM-mapping: 1: non-mapping 2: mapping " ::= { hwL2mcDTFwdEntry 23 } hwL2mcDTFwdHostFlag3 OBJECT-TYPE SYNTAX INTEGER { host(1), router(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "The type of an interface created on a router: 1: Interface connected to the host 2: Router interface that replicates multicast data flows " ::= { hwL2mcDTFwdEntry 24 } hwL2mcDTFwdHostFlag4 OBJECT-TYPE SYNTAX INTEGER { port(1), static(2), both(3) } MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates (S, G) table created : 1: from port; 2: from static; 3: from both the default falue is 1 " ::= { hwL2mcDTFwdEntry 25 } -- -- The hwDTGroupInfo group. -- hwL2mcDTGroupInfo OBJECT IDENTIFIER ::= { hwIgspMibObject 24 } hwL2mcDTGroupInfoTable OBJECT-TYPE SYNTAX SEQUENCE OF HWL2mcDTGroupInfoEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Table contains l2 multicast group information for IGMP Snooping." ::= { hwL2mcDTGroupInfo 1 } hwL2mcDTGroupInfoEntry OBJECT-TYPE SYNTAX HWL2mcDTGroupInfoEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry is created for each active VLAN or VSI in the device create a forwarding table entry and delete when a forwarding table entry deleted." INDEX { hwL2mcDTGroupSlotIndex, hwL2mcDTGroupVlanIndex, hwL2mcDTGroupVsiName, hwL2mcDTGroupGroupAddress, hwL2mcDTGroupSourceAddress, hwL2mcDTGroupFilterFlag, hwL2mcDTPortType, hwL2mcDTGroupPortIfIndex, hwL2mcDTGroupPortPeId, hwL2mcDTGroupPortCeId, hwL2mcDTGroupPeerAddress, hwL2mcDTGroupVcOrSiteId, hwL2mcDTGroupBoardNum } ::= { hwL2mcDTGroupInfoTable 1 } HWL2mcDTGroupInfoEntry ::= SEQUENCE { hwL2mcDTGroupSlotIndex Integer32, hwL2mcDTGroupVlanIndex VlanIdOrAny, hwL2mcDTGroupVsiName DisplayString, hwL2mcDTGroupGroupAddress IpAddress, hwL2mcDTGroupSourceAddress IpAddress, hwL2mcDTGroupFilterFlag INTEGER, hwL2mcDTPortType HWPortType, hwL2mcDTGroupPortIfIndex InterfaceIndexOrZero, hwL2mcDTGroupPortPeId VlanIdOrAny, hwL2mcDTGroupPortCeId VlanIdOrAny, hwL2mcDTGroupPeerAddress IpAddress, hwL2mcDTGroupVcOrSiteId Unsigned32, hwL2mcDTGroupBoardNum Integer32, hwL2mcDTSourceUpTime Counter32, hwL2mcDTSourceExpires Counter32, hwL2mcDTGroupUpTime Counter32, hwL2mcDTGroupExpires Counter32, hwL2mcDTGroupHostFlag1 INTEGER, hwL2mcDTGroupHostFlag2 INTEGER, hwL2mcDTGroupRowStatus RowStatus } hwL2mcDTGroupSlotIndex OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS not-accessible STATUS current DESCRIPTION "The slot index, which is interface board number. " ::= { hwL2mcDTGroupInfoEntry 1 } hwL2mcDTGroupVlanIndex OBJECT-TYPE SYNTAX VlanIdOrAny MAX-ACCESS not-accessible STATUS current DESCRIPTION "The VLAN ID, which is the configuration index in a VLAN. If a VSI is specified, the value is 4095. The value ranges from 1 to 4095. " ::= { hwL2mcDTGroupInfoEntry 2 } hwL2mcDTGroupVsiName OBJECT-TYPE SYNTAX DisplayString(SIZE (0..31)) MAX-ACCESS not-accessible STATUS current DESCRIPTION "The name of a VSI. If a VLAN is specified, the value is 32." ::= { hwL2mcDTGroupInfoEntry 3 } hwL2mcDTGroupGroupAddress OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS not-accessible STATUS current DESCRIPTION "The IP address of a multicast group." ::= { hwL2mcDTGroupInfoEntry 4 } hwL2mcDTGroupSourceAddress OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS not-accessible STATUS current DESCRIPTION "The source IP address of a multicast group." ::= { hwL2mcDTGroupInfoEntry 5 } hwL2mcDTGroupFilterFlag OBJECT-TYPE SYNTAX INTEGER { include(1), exclude(2), invalid(3) } MAX-ACCESS not-accessible STATUS current DESCRIPTION "The filtering mode: 1: include 2: exclude 3: invalid " ::= { hwL2mcDTGroupInfoEntry 6 } hwL2mcDTPortType OBJECT-TYPE SYNTAX HWPortType MAX-ACCESS not-accessible STATUS current DESCRIPTION "The interface type: 1: Invalid 2: PW interface 3: L2 interface 4: Encapsulation sub-interface 5: Termination sub-interface 6: Interface Board 7: Vlanif Port " ::= { hwL2mcDTGroupInfoEntry 7 } hwL2mcDTGroupPortIfIndex OBJECT-TYPE SYNTAX InterfaceIndexOrZero MAX-ACCESS not-accessible STATUS current DESCRIPTION "The interface index. The value 0 indicates that the interface index is invalid." ::= { hwL2mcDTGroupInfoEntry 8 } hwL2mcDTGroupPortPeId OBJECT-TYPE SYNTAX VlanIdOrAny MAX-ACCESS not-accessible STATUS current DESCRIPTION "The PE VID of an interface. The value ranges from 1 to 4095. The value 4095 indicates that the PE VID is invalid. " ::= { hwL2mcDTGroupInfoEntry 9 } hwL2mcDTGroupPortCeId OBJECT-TYPE SYNTAX VlanIdOrAny MAX-ACCESS not-accessible STATUS current DESCRIPTION "The CE VID of an interface. The value ranges from 1 to 4095. The value 0 indicates that the PE VID is invalid. " ::= { hwL2mcDTGroupInfoEntry 10 } hwL2mcDTGroupPeerAddress OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS not-accessible STATUS current DESCRIPTION "The peer IP address of a PW interface. The value 0.0.0.0 indicates that the IP address is invalid." ::= { hwL2mcDTGroupInfoEntry 11 } hwL2mcDTGroupVcOrSiteId OBJECT-TYPE SYNTAX Unsigned32(1..4294967295) MAX-ACCESS not-accessible STATUS current DESCRIPTION "The VC ID or SITE ID of a PW interface." ::= { hwL2mcDTGroupInfoEntry 12 } hwL2mcDTGroupBoardNum OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS not-accessible STATUS current DESCRIPTION "The interface board number." ::= { hwL2mcDTGroupInfoEntry 13 } hwL2mcDTSourceUpTime OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "How long the source group exists in the forwarding entry." ::= { hwL2mcDTGroupInfoEntry 21 } hwL2mcDTSourceExpires OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The timeout period of the source group in the forwarding entry, that is, the aging time of the source group." ::= { hwL2mcDTGroupInfoEntry 22 } hwL2mcDTGroupUpTime OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "How long the group exists in the forwarding entry." ::= { hwL2mcDTGroupInfoEntry 23 } hwL2mcDTGroupExpires OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "When the group expires in the forwarding entry, that is, the aging time of the source group." ::= { hwL2mcDTGroupInfoEntry 24 } hwL2mcDTGroupHostFlag1 OBJECT-TYPE SYNTAX INTEGER { static(1), dynamic(2), staticDynamic(3), invalid(4) } MAX-ACCESS read-only STATUS current DESCRIPTION "The mode to create an interface on the host: 1: static 2: dynamic 3: static and dynamic 4: invalid " ::= { hwL2mcDTGroupInfoEntry 26 } hwL2mcDTGroupHostFlag2 OBJECT-TYPE SYNTAX INTEGER { nonMapping(1), mapping(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "Whether an interface on the host is created through SSM-mapping: 1: non-mapping 2: mapping " ::= { hwL2mcDTGroupInfoEntry 27 } hwL2mcDTGroupRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-only STATUS current DESCRIPTION "The row status." ::= { hwL2mcDTGroupInfoEntry 100 } -- -- The hwL2mcMulticastTrafficPolicyCfgInfo group. -- hwL2mcMulticastTrafficPolicyCfgInfo OBJECT IDENTIFIER ::= { hwIgspMibObject 25 } hwL2mcMulticastTrafficPolicyCfgTable OBJECT-TYPE SYNTAX SEQUENCE OF HWL2mcMulticastTrafficPolicyCfgEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "In this table, you can query or configure whether to disable receive multicast traffic on a port." ::= { hwL2mcMulticastTrafficPolicyCfgInfo 1 } hwL2mcMulticastTrafficPolicyCfgEntry OBJECT-TYPE SYNTAX HWL2mcMulticastTrafficPolicyCfgEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry is created for each active VLAN or VSI in the device when disable receive multicast traffic on a port." INDEX { hwMulticastTrafficPolicyPortType, hwMulticastTrafficPolicyPortIfIndex, hwMulticastTrafficPolicyPortPeId, hwMulticastTrafficPolicyPortCeId, hwMulticastTrafficPolicyPortEndCeId, hwMulticastTrafficPolicyPeerAddress, hwMulticastTrafficPolicyVcOrSiteId,hwMulticastTrafficPolicyVlanIndex, hwMulticastTrafficPolicyVsiName, hwMulticastTrafficPolicyEndVlanIndex } ::= { hwL2mcMulticastTrafficPolicyCfgTable 1 } HWL2mcMulticastTrafficPolicyCfgEntry ::= SEQUENCE { hwMulticastTrafficPolicyPortType HWPortType, hwMulticastTrafficPolicyPortIfIndex InterfaceIndexOrZero, hwMulticastTrafficPolicyPortPeId VlanIdOrAny, hwMulticastTrafficPolicyPortCeId VlanIdOrAny, hwMulticastTrafficPolicyPortEndCeId VlanIdOrAny, hwMulticastTrafficPolicyPeerAddress IpAddress, hwMulticastTrafficPolicyVcOrSiteId Unsigned32, hwMulticastTrafficPolicyVlanIndex VlanIdOrAny, hwMulticastTrafficPolicyEndVlanIndex VlanIdOrAny, hwMulticastTrafficPolicyVsiName DisplayString, hwMulticastTrafficPolicyRowStatus RowStatus } hwMulticastTrafficPolicyPortType OBJECT-TYPE SYNTAX HWPortType MAX-ACCESS not-accessible STATUS current DESCRIPTION "The interface type: 1: Invalid 2: PW interface 3: L2 interface 4: Encapsulation sub-interface 5: Termination sub-interface 6: Interface Board 7: Vlanif Port " ::= { hwL2mcMulticastTrafficPolicyCfgEntry 1 } hwMulticastTrafficPolicyPortIfIndex OBJECT-TYPE SYNTAX InterfaceIndexOrZero MAX-ACCESS not-accessible STATUS current DESCRIPTION "The interface index. The value 0 indicates that the interface index is invalid." ::= { hwL2mcMulticastTrafficPolicyCfgEntry 2 } hwMulticastTrafficPolicyPortPeId OBJECT-TYPE SYNTAX VlanIdOrAny MAX-ACCESS not-accessible STATUS current DESCRIPTION "The PE VID of an interface. The value ranges from 1 to 4095. The value 4095 indicates that the PE VID is invalid. " ::= { hwL2mcMulticastTrafficPolicyCfgEntry 3 } hwMulticastTrafficPolicyPortCeId OBJECT-TYPE SYNTAX VlanIdOrAny MAX-ACCESS not-accessible STATUS current DESCRIPTION "The CE VID of an interface. The value ranges from 1 to 4095. The value 4095 indicates that the PE VID is invalid. " ::= { hwL2mcMulticastTrafficPolicyCfgEntry 4 } hwMulticastTrafficPolicyPortEndCeId OBJECT-TYPE SYNTAX VlanIdOrAny MAX-ACCESS not-accessible STATUS current DESCRIPTION "The CE VID of an interface. The value ranges from 1 to 4095. The value 4095 indicates that the PE VID is invalid. " ::= { hwL2mcMulticastTrafficPolicyCfgEntry 5 } hwMulticastTrafficPolicyPeerAddress OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS not-accessible STATUS current DESCRIPTION "The peer IP address of a PW interface. The value 0.0.0.0 indicates that the IP address is invalid." ::= { hwL2mcMulticastTrafficPolicyCfgEntry 6 } hwMulticastTrafficPolicyVcOrSiteId OBJECT-TYPE SYNTAX Unsigned32(1..4294967295) MAX-ACCESS not-accessible STATUS current DESCRIPTION "The VC ID or SITE ID of a PW interface." ::= { hwL2mcMulticastTrafficPolicyCfgEntry 7 } hwMulticastTrafficPolicyVlanIndex OBJECT-TYPE SYNTAX VlanIdOrAny MAX-ACCESS not-accessible STATUS current DESCRIPTION "The VLAN ID, which is the configuration index in a VLAN. If a VSI is specified, the value is 4095. The value ranges from 1 to 4095. " ::= { hwL2mcMulticastTrafficPolicyCfgEntry 8 } hwMulticastTrafficPolicyEndVlanIndex OBJECT-TYPE SYNTAX VlanIdOrAny MAX-ACCESS not-accessible STATUS current DESCRIPTION "The VLAN ID, which is the configuration index in a VLAN. If a VSI is specified, the value is 4095. The value ranges from 1 to 4095. " ::= { hwL2mcMulticastTrafficPolicyCfgEntry 9 } hwMulticastTrafficPolicyVsiName OBJECT-TYPE SYNTAX DisplayString(SIZE (0..31)) MAX-ACCESS not-accessible STATUS current DESCRIPTION "The name of a VSI. If a VLAN is specified, the value is 32." ::= { hwL2mcMulticastTrafficPolicyCfgEntry 10 } hwMulticastTrafficPolicyRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "The row status." ::= { hwL2mcMulticastTrafficPolicyCfgEntry 100 } -- -- The hwL2mcRouteLearnDisablePolicyCfgInfo group. -- hwL2mcRouteLearnDisablePolicyCfgInfo OBJECT IDENTIFIER ::= { hwIgspMibObject 26 } hwL2mcRouteLearnDisablePolicyCfgTable OBJECT-TYPE SYNTAX SEQUENCE OF HWL2mcRouteLearnDisablePolicyCfgEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "In this table, you can query or configure whether to disable router port learning on a port." ::= { hwL2mcRouteLearnDisablePolicyCfgInfo 1 } hwL2mcRouteLearnDisablePolicyCfgEntry OBJECT-TYPE SYNTAX HWL2mcRouteLearnDisablePolicyCfgEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry is created for each active VLAN or VSI in the device when disable router port learning on a port." INDEX { hwRouteLearnDisablePolicyPortType, hwRouteLearnDisablePolicyPortIfIndex, hwRouteLearnDisablePolicyPortPeId, hwRouteLearnDisablePolicyPortCeId, hwRouteLearnDisablePolicyPortEndCeId, hwRouteLearnDisablePolicyPeerAddress, hwRouteLearnDisablePolicyVcOrSiteId,hwRouteLearnDisablePolicyVlanIndex, hwRouteLearnDisablePolicyEndVlanIndex, hwRouteLearnDisablePolicyVsiName } ::= { hwL2mcRouteLearnDisablePolicyCfgTable 1 } HWL2mcRouteLearnDisablePolicyCfgEntry ::= SEQUENCE { hwRouteLearnDisablePolicyPortType HWPortType, hwRouteLearnDisablePolicyPortIfIndex InterfaceIndexOrZero, hwRouteLearnDisablePolicyPortPeId VlanIdOrAny, hwRouteLearnDisablePolicyPortCeId VlanIdOrAny, hwRouteLearnDisablePolicyPortEndCeId VlanIdOrAny, hwRouteLearnDisablePolicyPeerAddress IpAddress, hwRouteLearnDisablePolicyVcOrSiteId Unsigned32, hwRouteLearnDisablePolicyVlanIndex VlanIdOrAny, hwRouteLearnDisablePolicyEndVlanIndex VlanIdOrAny, hwRouteLearnDisablePolicyVsiName DisplayString, hwRouteLearnDisablePolicyRowStatus RowStatus } hwRouteLearnDisablePolicyPortType OBJECT-TYPE SYNTAX HWPortType MAX-ACCESS not-accessible STATUS current DESCRIPTION "The interface type: 1: Invalid 2: PW interface 3: L2 interface 4: Encapsulation sub-interface 5: Termination sub-interface 6: Interface Board 7: Vlanif Port " ::= { hwL2mcRouteLearnDisablePolicyCfgEntry 1 } hwRouteLearnDisablePolicyPortIfIndex OBJECT-TYPE SYNTAX InterfaceIndexOrZero MAX-ACCESS not-accessible STATUS current DESCRIPTION "The interface index. The value 0 indicates that the interface index is invalid." ::= { hwL2mcRouteLearnDisablePolicyCfgEntry 2 } hwRouteLearnDisablePolicyPortPeId OBJECT-TYPE SYNTAX VlanIdOrAny MAX-ACCESS not-accessible STATUS current DESCRIPTION "The PE VID of an interface. The value ranges from 1 to 4095. The value 4095 indicates that the PE VID is invalid. " ::= { hwL2mcRouteLearnDisablePolicyCfgEntry 3 } hwRouteLearnDisablePolicyPortCeId OBJECT-TYPE SYNTAX VlanIdOrAny MAX-ACCESS not-accessible STATUS current DESCRIPTION "The CE VID of an interface. The value ranges from 1 to 4095. The value 4095 indicates that the CE VID is invalid. " ::= { hwL2mcRouteLearnDisablePolicyCfgEntry 4 } hwRouteLearnDisablePolicyPortEndCeId OBJECT-TYPE SYNTAX VlanIdOrAny MAX-ACCESS not-accessible STATUS current DESCRIPTION "The CE VID of an interface. The value ranges from 1 to 4095. The value 4095 indicates that the CE VID is invalid. " ::= { hwL2mcRouteLearnDisablePolicyCfgEntry 5 } hwRouteLearnDisablePolicyPeerAddress OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS not-accessible STATUS current DESCRIPTION "The peer IP address of a PW interface. The value 0.0.0.0 indicates that the IP address is invalid." ::= { hwL2mcRouteLearnDisablePolicyCfgEntry 6 } hwRouteLearnDisablePolicyVcOrSiteId OBJECT-TYPE SYNTAX Unsigned32(1..4294967295) MAX-ACCESS not-accessible STATUS current DESCRIPTION "The VC ID or SITE ID of a PW interface." ::= { hwL2mcRouteLearnDisablePolicyCfgEntry 7 } hwRouteLearnDisablePolicyVlanIndex OBJECT-TYPE SYNTAX VlanIdOrAny MAX-ACCESS not-accessible STATUS current DESCRIPTION "The VLAN ID, which is the configuration index in a VLAN. If a VSI is specified, the value is 4095. The value ranges from 1 to 4095. " ::= { hwL2mcRouteLearnDisablePolicyCfgEntry 8 } hwRouteLearnDisablePolicyEndVlanIndex OBJECT-TYPE SYNTAX VlanIdOrAny MAX-ACCESS not-accessible STATUS current DESCRIPTION "The VLAN ID, which is the configuration index in a VLAN. If a VSI is specified, the value is 4095. The value ranges from 1 to 4095. " ::= { hwL2mcRouteLearnDisablePolicyCfgEntry 9 } hwRouteLearnDisablePolicyVsiName OBJECT-TYPE SYNTAX DisplayString(SIZE (0..31)) MAX-ACCESS not-accessible STATUS current DESCRIPTION "The name of a VSI. If a VLAN is specified, the value is 32." ::= { hwL2mcRouteLearnDisablePolicyCfgEntry 10 } hwRouteLearnDisablePolicyRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "The row status." ::= { hwL2mcRouteLearnDisablePolicyCfgEntry 100 } -- -- The hwL2mcTrackVRRPCfgInfo group. -- hwL2mcTrackVRRPCfgInfo OBJECT IDENTIFIER ::= { hwIgspMibObject 27 } hwL2mcTrackVRRPCfgTable OBJECT-TYPE SYNTAX SEQUENCE OF HWL2mcTrackVRRPCfgEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "In this table, you can query or configure a port to track VRRP." ::= { hwL2mcTrackVRRPCfgInfo 1 } hwL2mcTrackVRRPCfgEntry OBJECT-TYPE SYNTAX HWL2mcTrackVRRPCfgEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry is created for each active VLAN or VSI in the device when configure a port to track VRRP." INDEX { hwTrackVRRPPortType, hwTrackVRRPPortIfIndex, hwTrackVRRPPortPeId, hwTrackVRRPPortCeId, hwTrackVRRPPortEndCeId, hwTrackVRRPVlanIndex, hwTrackVRRPEndVlanIndex, hwTrackVRRPVsiName } ::= { hwL2mcTrackVRRPCfgTable 1 } HWL2mcTrackVRRPCfgEntry ::= SEQUENCE { hwTrackVRRPPortType HWPortType, hwTrackVRRPPortIfIndex InterfaceIndexOrZero, hwTrackVRRPPortPeId VlanIdOrAny, hwTrackVRRPPortCeId VlanIdOrAny, hwTrackVRRPPortEndCeId VlanIdOrAny, hwTrackVRRPVlanIndex VlanIdOrAny, hwTrackVRRPEndVlanIndex VlanIdOrAny, hwTrackVRRPVsiName DisplayString, hwTrackVRRPVridIfIndex InterfaceIndexOrZero, hwTrackVRRPVridID Unsigned32, hwTrackVRRPRowStatus RowStatus } hwTrackVRRPPortType OBJECT-TYPE SYNTAX HWPortType MAX-ACCESS not-accessible STATUS current DESCRIPTION "The interface type: 1: Invalid 2: PW interface 3: L2 interface 4: Encapsulation sub-interface 5: Termination sub-interface 6: Interface Board 7: Vlanif Port " ::= { hwL2mcTrackVRRPCfgEntry 1 } hwTrackVRRPPortIfIndex OBJECT-TYPE SYNTAX InterfaceIndexOrZero MAX-ACCESS not-accessible STATUS current DESCRIPTION "The interface index. The value 0 indicates that the interface index is invalid." ::= { hwL2mcTrackVRRPCfgEntry 2 } hwTrackVRRPPortPeId OBJECT-TYPE SYNTAX VlanIdOrAny MAX-ACCESS not-accessible STATUS current DESCRIPTION "The PE VID of an interface. The value ranges from 1 to 4095. The value 4095 indicates that the PE VID is invalid. " ::= { hwL2mcTrackVRRPCfgEntry 3 } hwTrackVRRPPortCeId OBJECT-TYPE SYNTAX VlanIdOrAny MAX-ACCESS not-accessible STATUS current DESCRIPTION "The CE VID of an interface. The value ranges from 1 to 4095. The value 4095 indicates that the CE VID is invalid. " ::= { hwL2mcTrackVRRPCfgEntry 4 } hwTrackVRRPPortEndCeId OBJECT-TYPE SYNTAX VlanIdOrAny MAX-ACCESS not-accessible STATUS current DESCRIPTION "The CE VID of an interface. The value ranges from 1 to 4095. The value 4095 indicates that the CE VID is invalid. " ::= { hwL2mcTrackVRRPCfgEntry 5 } hwTrackVRRPVlanIndex OBJECT-TYPE SYNTAX VlanIdOrAny MAX-ACCESS not-accessible STATUS current DESCRIPTION "The VLAN ID, which is the configuration index in a VLAN. If a VSI is specified, the value is 4095. The value ranges from 1 to 4095. " ::= { hwL2mcTrackVRRPCfgEntry 6 } hwTrackVRRPEndVlanIndex OBJECT-TYPE SYNTAX VlanIdOrAny MAX-ACCESS not-accessible STATUS current DESCRIPTION "The VLAN ID, which is the configuration index in a VLAN. If a VSI is specified, the value is 4095. The value ranges from 1 to 4095. " ::= { hwL2mcTrackVRRPCfgEntry 7 } hwTrackVRRPVsiName OBJECT-TYPE SYNTAX DisplayString(SIZE (0..31)) MAX-ACCESS not-accessible STATUS current DESCRIPTION "The name of a VSI. If a VLAN is specified, the value is 32." ::= { hwL2mcTrackVRRPCfgEntry 8 } hwTrackVRRPVridIfIndex OBJECT-TYPE SYNTAX InterfaceIndexOrZero MAX-ACCESS read-create STATUS current DESCRIPTION "The interface index. The value 0 indicates that the interface index is invalid." ::= { hwL2mcTrackVRRPCfgEntry 9 } hwTrackVRRPVridID OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-create STATUS current DESCRIPTION "The VRRP VRID." ::= { hwL2mcTrackVRRPCfgEntry 10 } hwTrackVRRPRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "The row status." ::= { hwL2mcTrackVRRPCfgEntry 100 } -- -- The hwL2mcMInstCfgInfo group. -- hwL2mcMInstCfgInfo OBJECT IDENTIFIER ::= { hwIgspMibObject 28 } hwL2mcMInstCfgTable OBJECT-TYPE SYNTAX SEQUENCE OF HWL2mcMInstCfgEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table create or modified multicast Instance." ::= { hwL2mcMInstCfgInfo 1 } hwL2mcMInstCfgEntry OBJECT-TYPE SYNTAX HWL2mcMInstCfgEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry is created for each active VLAN or VSI in the device when disable router port learning on a port." INDEX { hwL2mcMInstId } ::= { hwL2mcMInstCfgTable 1 } HWL2mcMInstCfgEntry ::= SEQUENCE { hwL2mcMInstId Unsigned32, hwL2mcMInstVlanIndex VlanIdOrAnyOrNone, hwL2mcMInstVsiName DisplayString, hwL2mcMInstProtectInst Unsigned32, hwL2mcMInstRowStatus RowStatus } hwL2mcMInstId OBJECT-TYPE SYNTAX Unsigned32(1..32) MAX-ACCESS not-accessible STATUS current DESCRIPTION "L2 multicast instance ID" ::= { hwL2mcMInstCfgEntry 1 } hwL2mcMInstVlanIndex OBJECT-TYPE SYNTAX VlanIdOrAnyOrNone MAX-ACCESS read-create STATUS current DESCRIPTION "Multicast-VLAN ID" ::= { hwL2mcMInstCfgEntry 2 } hwL2mcMInstVsiName OBJECT-TYPE SYNTAX DisplayString(SIZE (0..31)) MAX-ACCESS read-create STATUS current DESCRIPTION "Multicast-VSI name" ::= { hwL2mcMInstCfgEntry 3 } hwL2mcMInstProtectInst OBJECT-TYPE SYNTAX Unsigned32(1..32) MAX-ACCESS read-create STATUS current DESCRIPTION "L2 multicast protect instance ID" ::= { hwL2mcMInstCfgEntry 4 } hwL2mcMInstRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "The row status." ::= { hwL2mcMInstCfgEntry 100 } hwL2mcMInstGroupCfgTable OBJECT-TYPE SYNTAX SEQUENCE OF HWL2mcMInstGroupCfgEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Thist table configure multicast instance mulitcast group infomation." ::= { hwL2mcMInstCfgInfo 2 } hwL2mcMInstGroupCfgEntry OBJECT-TYPE SYNTAX HWL2mcMInstGroupCfgEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "." INDEX { hwL2mcMInstGroupId, hwL2mcMInstGroupAddress, hwL2mcMinstGroupAddressMask } ::= { hwL2mcMInstGroupCfgTable 1 } HWL2mcMInstGroupCfgEntry ::= SEQUENCE { hwL2mcMInstGroupId Unsigned32, hwL2mcMInstGroupAddress IpAddress, hwL2mcMinstGroupAddressMask IpAddress, hwL2mcMInstGroupRowStatus RowStatus } hwL2mcMInstGroupId OBJECT-TYPE SYNTAX Unsigned32(1..32) MAX-ACCESS not-accessible STATUS current DESCRIPTION "L2 multicast instance ID" ::= { hwL2mcMInstGroupCfgEntry 1 } hwL2mcMInstGroupAddress OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS not-accessible STATUS current DESCRIPTION "Group address." ::= { hwL2mcMInstGroupCfgEntry 2 } hwL2mcMinstGroupAddressMask OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS not-accessible STATUS current DESCRIPTION "Group address." ::= { hwL2mcMInstGroupCfgEntry 3 } hwL2mcMInstGroupRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "The row status." ::= { hwL2mcMInstGroupCfgEntry 100 } hwL2mcMInstUserCfgTable OBJECT-TYPE SYNTAX SEQUENCE OF HWL2mcMInstUserCfgEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "User instance in the multicast instance." ::= { hwL2mcMInstCfgInfo 3 } hwL2mcMInstUserCfgEntry OBJECT-TYPE SYNTAX HWL2mcMInstUserCfgEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "." INDEX { hwL2mcMInstUserMInstId, hwL2mcMInstUserVLANID, hwL2mcMInstUserEndVLANID, hwL2mcMInstUserVSIName } ::= { hwL2mcMInstUserCfgTable 1 } HWL2mcMInstUserCfgEntry ::= SEQUENCE { hwL2mcMInstUserMInstId Unsigned32, hwL2mcMInstUserVLANID VlanIdOrAnyOrNone, hwL2mcMInstUserEndVLANID VlanIdOrAnyOrNone, hwL2mcMInstUserVSIName DisplayString, hwL2mcMInstUserRowStatus RowStatus } hwL2mcMInstUserMInstId OBJECT-TYPE SYNTAX Unsigned32(1..32) MAX-ACCESS not-accessible STATUS current DESCRIPTION "L2 multicast instance ID" ::= { hwL2mcMInstUserCfgEntry 1 } hwL2mcMInstUserVLANID OBJECT-TYPE SYNTAX VlanIdOrAnyOrNone MAX-ACCESS not-accessible STATUS current DESCRIPTION "User VLAN ID." ::= { hwL2mcMInstUserCfgEntry 2 } hwL2mcMInstUserEndVLANID OBJECT-TYPE SYNTAX VlanIdOrAnyOrNone MAX-ACCESS not-accessible STATUS current DESCRIPTION "User End VLAN ID." ::= { hwL2mcMInstUserCfgEntry 3 } hwL2mcMInstUserVSIName OBJECT-TYPE SYNTAX DisplayString(SIZE (0..31)) MAX-ACCESS not-accessible STATUS current DESCRIPTION "VSI name." ::= { hwL2mcMInstUserCfgEntry 4 } hwL2mcMInstUserRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "The row status." ::= { hwL2mcMInstUserCfgEntry 100 } -- -- The hwL2mcStaticGroupCfgInfo group. -- hwL2mcStaticGroupCfgInfo OBJECT IDENTIFIER ::= { hwIgspMibObject 29 } hwL2mcStaticGroupCfgTable OBJECT-TYPE SYNTAX SEQUENCE OF HWL2mcStaticGroupCfgEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Table contains l2 multicast static group information for IGMP Snooping." ::= { hwL2mcStaticGroupCfgInfo 1 } hwL2mcStaticGroupCfgEntry OBJECT-TYPE SYNTAX HWL2mcStaticGroupCfgEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry is created for each active VLAN or VSI in the device create a static group entry and delete when a static group entry deleted." INDEX { hwStaticGroupCfgPortType, hwStaticGroupCfgPortIfIndex, hwStaticGroupCfgPortPeId, hwStaticGroupCfgPortPeIdEnd, hwStaticGroupCfgPortCeId, hwStaticGroupCfgPortCeIdEnd, hwStaticGroupCfgPeerAddress, hwStaticGroupCfgVcOrSiteId, hwStaticGroupCfgVlanIndex, hwStaticGroupCfgVsiName, hwStaticGroupCfgGroupAddress, hwStaticGroupCfgSourceAddress } ::= { hwL2mcStaticGroupCfgTable 1 } HWL2mcStaticGroupCfgEntry ::= SEQUENCE { hwStaticGroupCfgPortType HWPortType, hwStaticGroupCfgPortIfIndex InterfaceIndexOrZero, hwStaticGroupCfgPortPeId VlanIdOrAny, hwStaticGroupCfgPortPeIdEnd VlanIdOrAny, hwStaticGroupCfgPortCeId VlanIdOrAny, hwStaticGroupCfgPortCeIdEnd VlanIdOrAny, hwStaticGroupCfgPeerAddress IpAddress, hwStaticGroupCfgVcOrSiteId Unsigned32, hwStaticGroupCfgVlanIndex VlanIdOrAny, hwStaticGroupCfgVsiName DisplayString, hwStaticGroupCfgGroupAddress IpAddress, hwStaticGroupCfgSourceAddress IpAddress, hwStaticGroupCfgRowStatus RowStatus } hwStaticGroupCfgPortType OBJECT-TYPE SYNTAX HWPortType MAX-ACCESS not-accessible STATUS current DESCRIPTION "The interface type: 1: Invalid 2: PW interface 3: L2 interface 4: Encapsulation sub-interface 5: Termination sub-interface 6: Interface Board 7: Vlanif Port " ::= { hwL2mcStaticGroupCfgEntry 1 } hwStaticGroupCfgPortIfIndex OBJECT-TYPE SYNTAX InterfaceIndexOrZero MAX-ACCESS not-accessible STATUS current DESCRIPTION "The interface index. The value 0 indicates that the interface index is invalid." ::= { hwL2mcStaticGroupCfgEntry 2 } hwStaticGroupCfgPortPeId OBJECT-TYPE SYNTAX VlanIdOrAny MAX-ACCESS not-accessible STATUS current DESCRIPTION "The begin of a PE VID batch. The value ranges from 1 to 4095. The value 4095 indicates that the PE VID is invalid. " ::= { hwL2mcStaticGroupCfgEntry 3 } hwStaticGroupCfgPortPeIdEnd OBJECT-TYPE SYNTAX VlanIdOrAny MAX-ACCESS not-accessible STATUS current DESCRIPTION "The end of a PE VID batch. The value ranges from 1 to 4095. The value 4095 indicates that the PE VID is invalid. " ::= { hwL2mcStaticGroupCfgEntry 4 } hwStaticGroupCfgPortCeId OBJECT-TYPE SYNTAX VlanIdOrAny MAX-ACCESS not-accessible STATUS current DESCRIPTION "The begin of a CE VID batch. The value ranges from 1 to 4095. The value 0 indicates that the PE VID is invalid. " ::= { hwL2mcStaticGroupCfgEntry 5 } hwStaticGroupCfgPortCeIdEnd OBJECT-TYPE SYNTAX VlanIdOrAny MAX-ACCESS not-accessible STATUS current DESCRIPTION "The end of a CE VID batch. The value ranges from 1 to 4095. The value 0 indicates that the PE VID is invalid. " ::= { hwL2mcStaticGroupCfgEntry 6 } hwStaticGroupCfgPeerAddress OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS not-accessible STATUS current DESCRIPTION "The peer IP address of a PW interface. The value 0.0.0.0 indicates that the IP address is invalid." ::= { hwL2mcStaticGroupCfgEntry 7 } hwStaticGroupCfgVcOrSiteId OBJECT-TYPE SYNTAX Unsigned32(1..4294967295) MAX-ACCESS not-accessible STATUS current DESCRIPTION "The VC ID or SITE ID of a PW interface." ::= { hwL2mcStaticGroupCfgEntry 8 } hwStaticGroupCfgVlanIndex OBJECT-TYPE SYNTAX VlanIdOrAny MAX-ACCESS not-accessible STATUS current DESCRIPTION "The VLAN ID, which is the configuration index in a VLAN. If a VSI is specified, the value is 4095. The value ranges from 1 to 4095. " ::= { hwL2mcStaticGroupCfgEntry 9 } hwStaticGroupCfgVsiName OBJECT-TYPE SYNTAX DisplayString(SIZE (0..31)) MAX-ACCESS not-accessible STATUS current DESCRIPTION "The name of a VSI. If a VLAN is specified, the value is 32." ::= { hwL2mcStaticGroupCfgEntry 10 } hwStaticGroupCfgGroupAddress OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS not-accessible STATUS current DESCRIPTION "The group address of a multicast group. In the case of MAC forwarding, the group address is the smallest of 32 IP addresses." ::= { hwL2mcStaticGroupCfgEntry 11 } hwStaticGroupCfgSourceAddress OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS not-accessible STATUS current DESCRIPTION "The source IP address of a multicast group." ::= { hwL2mcStaticGroupCfgEntry 12 } hwStaticGroupCfgRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "The row status." ::= { hwL2mcStaticGroupCfgEntry 100 } -- -- The hwL2mcPortGroupPolicyBatchCfgInfo group. -- hwL2mcPortGroupPolicyBatchCfgInfo OBJECT IDENTIFIER ::= { hwIgspMibObject 30 } hwL2mcPortGroupPolicyBatchCfgTable OBJECT-TYPE SYNTAX SEQUENCE OF HWL2mcPortGroupPolicyBatchCfgEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "In this table, you can query or configure a group policy to filter entries on a port." ::= { hwL2mcPortGroupPolicyBatchCfgInfo 1 } hwL2mcPortGroupPolicyBatchCfgEntry OBJECT-TYPE SYNTAX HWL2mcPortGroupPolicyBatchCfgEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry is created for each active VLAN or VSI in the device when a group policy added." INDEX { hwPortGroupPolicyCfgPortType, hwPortGroupPolicyCfgPortIfIndex, hwPortGroupPolicyCfgPortPeId, hwPortGroupPolicyCfgPortPeIdEnd, hwPortGroupPolicyCfgPortCeId, hwPortGroupPolicyCfgPortCeIdEnd, hwPortGroupPolicyCfgPeerAddress, hwPortGroupPolicyCfgVcOrSiteId, hwPortGroupPolicyCfgVlanIndex, hwPortGroupPolicyCfgVsiName } ::= { hwL2mcPortGroupPolicyBatchCfgTable 1 } HWL2mcPortGroupPolicyBatchCfgEntry ::= SEQUENCE { hwPortGroupPolicyCfgPortType HWPortType, hwPortGroupPolicyCfgPortIfIndex InterfaceIndexOrZero, hwPortGroupPolicyCfgPortPeId VlanIdOrAny, hwPortGroupPolicyCfgPortPeIdEnd VlanIdOrAny, hwPortGroupPolicyCfgPortCeId VlanIdOrAny, hwPortGroupPolicyCfgPortCeIdEnd VlanIdOrAny, hwPortGroupPolicyCfgPeerAddress IpAddress, hwPortGroupPolicyCfgVcOrSiteId Unsigned32, hwPortGroupPolicyCfgVlanIndex VlanIdOrAny, hwPortGroupPolicyCfgVsiName DisplayString, hwPortGroupPolicyCfgAclNum Integer32, hwPortGroupPolicyCfgIgmpVersion INTEGER, hwPortGroupPolicyCfgRowStatus RowStatus } hwPortGroupPolicyCfgPortType OBJECT-TYPE SYNTAX HWPortType MAX-ACCESS not-accessible STATUS current DESCRIPTION "The interface type: 1: Invalid 2: PW interface 3: L2 interface 4: Encapsulation sub-interface 5: Termination sub-interface 6: Interface Board 7: Vlanif Port " ::= { hwL2mcPortGroupPolicyBatchCfgEntry 1 } hwPortGroupPolicyCfgPortIfIndex OBJECT-TYPE SYNTAX InterfaceIndexOrZero MAX-ACCESS not-accessible STATUS current DESCRIPTION "The interface index. The value 0 indicates that the interface index is invalid." ::= { hwL2mcPortGroupPolicyBatchCfgEntry 2 } hwPortGroupPolicyCfgPortPeId OBJECT-TYPE SYNTAX VlanIdOrAny MAX-ACCESS not-accessible STATUS current DESCRIPTION "The begin of a PE VID batch. The value ranges from 1 to 4095. The value 4095 indicates that the PE VID is invalid. " ::= { hwL2mcPortGroupPolicyBatchCfgEntry 3 } hwPortGroupPolicyCfgPortPeIdEnd OBJECT-TYPE SYNTAX VlanIdOrAny MAX-ACCESS not-accessible STATUS current DESCRIPTION "The end of a PE VID batch. The value ranges from 1 to 4095. The value 4095 indicates that the PE VID is invalid. " ::= { hwL2mcPortGroupPolicyBatchCfgEntry 4 } hwPortGroupPolicyCfgPortCeId OBJECT-TYPE SYNTAX VlanIdOrAny MAX-ACCESS not-accessible STATUS current DESCRIPTION "The begin of a CE VID batch. The value ranges from 1 to 4095. The value 4095 indicates that the PE VID is invalid. " ::= { hwL2mcPortGroupPolicyBatchCfgEntry 5 } hwPortGroupPolicyCfgPortCeIdEnd OBJECT-TYPE SYNTAX VlanIdOrAny MAX-ACCESS not-accessible STATUS current DESCRIPTION "The end of a CE VID batch. The value ranges from 1 to 4095. The value 4095 indicates that the PE VID is invalid. " ::= { hwL2mcPortGroupPolicyBatchCfgEntry 6 } hwPortGroupPolicyCfgPeerAddress OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS not-accessible STATUS current DESCRIPTION "The peer IP address of a PW interface. The value 0.0.0.0 indicates that the IP address is invalid." ::= { hwL2mcPortGroupPolicyBatchCfgEntry 7 } hwPortGroupPolicyCfgVcOrSiteId OBJECT-TYPE SYNTAX Unsigned32(1..4294967295) MAX-ACCESS not-accessible STATUS current DESCRIPTION "The VC ID or SITE ID of a PW interface." ::= { hwL2mcPortGroupPolicyBatchCfgEntry 8 } hwPortGroupPolicyCfgVlanIndex OBJECT-TYPE SYNTAX VlanIdOrAny MAX-ACCESS not-accessible STATUS current DESCRIPTION "The VLAN ID, which is the configuration index in a VLAN. If a VSI is specified, the value is 4095. The value ranges from 1 to 4095. " ::= { hwL2mcPortGroupPolicyBatchCfgEntry 9 } hwPortGroupPolicyCfgVsiName OBJECT-TYPE SYNTAX DisplayString(SIZE (0..31)) MAX-ACCESS not-accessible STATUS current DESCRIPTION "The name of a VSI. If a VLAN is specified, the value is 32." ::= { hwL2mcPortGroupPolicyBatchCfgEntry 10 } hwPortGroupPolicyCfgAclNum OBJECT-TYPE SYNTAX Integer32(0|2000..3999) MAX-ACCESS read-create STATUS current DESCRIPTION "The number of a basic ACL. The ACL number ranges from 2000 to 3999. The default value is 0, indicating that the value is invalid. " ::= { hwL2mcPortGroupPolicyBatchCfgEntry 11 } hwPortGroupPolicyCfgIgmpVersion OBJECT-TYPE SYNTAX INTEGER { versionAll(0), version1(1), version2(2), version3(3) } MAX-ACCESS read-create STATUS current DESCRIPTION "The IGMP version. The value ranges from 0 to 3. The default is 0, indicating that no version is specified. " ::= { hwL2mcPortGroupPolicyBatchCfgEntry 12 } hwPortGroupPolicyCfgRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "The row status." ::= { hwL2mcPortGroupPolicyBatchCfgEntry 100 } -- -- The hwL2mcCACPortLimitInfo group. -- hwL2mcCACPortLimitInfo OBJECT IDENTIFIER ::= { hwIgspMibObject 31 } hwL2mcCACPortLimitTable OBJECT-TYPE SYNTAX SEQUENCE OF HWL2mcCACPortLimitEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table describes the configurations of IGMP snooping CAC on an interface." ::= { hwL2mcCACPortLimitInfo 1 } hwL2mcCACPortLimitEntry OBJECT-TYPE SYNTAX HWL2mcCACPortLimitEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry is created for each IGMP snooping CAC on an interface." INDEX { hwCACPortLimitVlanIndex, hwCACPortLimitVsiName, hwCACPortLimitPortType, hwCACPortLimitIfIndex, hwCACPortLimitPeId, hwCACPortLimitPeIdEnd, hwCACPortLimitCeId, hwCACPortLimitCeIdEnd, hwCACPortLimitPeerAddress, hwCACPortLimitVcOrSiteId, hwCACPortLimitChnlName } ::= { hwL2mcCACPortLimitTable 1 } HWL2mcCACPortLimitEntry ::= SEQUENCE { hwCACPortLimitVlanIndex VlanIdOrAny, hwCACPortLimitVsiName DisplayString, hwCACPortLimitPortType HWPortType, hwCACPortLimitIfIndex InterfaceIndexOrZero, hwCACPortLimitPeId VlanIdOrAny, hwCACPortLimitPeIdEnd VlanIdOrAny, hwCACPortLimitCeId VlanIdOrAny, hwCACPortLimitCeIdEnd VlanIdOrAny, hwCACPortLimitPeerAddress IpAddress, hwCACPortLimitVcOrSiteId Unsigned32, hwCACPortLimitChnlName DisplayString, hwCACPortLimitAcl Integer32, hwCACPortLimitMaxEntry Integer32, hwCACPortLimitEntryCnt Counter32, hwCACPortLimitMaxBandWidth Integer32, hwCACPortLimitBandWidth Counter32, hwCACPortLimitCfgRowStatus RowStatus } hwCACPortLimitVlanIndex OBJECT-TYPE SYNTAX VlanIdOrAny MAX-ACCESS not-accessible STATUS current DESCRIPTION "The VLAN ID, which is the configuration index in a VLAN. If a VSI is specified, the value is 4095. The value ranges from 1 to 4095. " ::= { hwL2mcCACPortLimitEntry 1 } hwCACPortLimitVsiName OBJECT-TYPE SYNTAX DisplayString(SIZE (0..31)) MAX-ACCESS not-accessible STATUS current DESCRIPTION "The name of a VSI. If a VLAN is specified, the value is 32." ::= { hwL2mcCACPortLimitEntry 2 } hwCACPortLimitPortType OBJECT-TYPE SYNTAX HWPortType MAX-ACCESS not-accessible STATUS current DESCRIPTION "The interface type: 1: Invalid 2: PW interface 3: L2 interface 4: Encapsulation sub-interface 5: Termination sub-interface 6: Interface Board 7: Vlanif Port " ::= { hwL2mcCACPortLimitEntry 3 } hwCACPortLimitIfIndex OBJECT-TYPE SYNTAX InterfaceIndexOrZero MAX-ACCESS not-accessible STATUS current DESCRIPTION "The interface index. The value 0 indicates that the interface index is invalid." ::= { hwL2mcCACPortLimitEntry 4 } hwCACPortLimitPeId OBJECT-TYPE SYNTAX VlanIdOrAny MAX-ACCESS not-accessible STATUS current DESCRIPTION "The begin of a PE VID batch. The value ranges from 1 to 4095. The value 4095 indicates that the PE VID is invalid. " ::= { hwL2mcCACPortLimitEntry 5 } hwCACPortLimitPeIdEnd OBJECT-TYPE SYNTAX VlanIdOrAny MAX-ACCESS not-accessible STATUS current DESCRIPTION "The end of a PE VID batch. The value ranges from 1 to 4095. The value 4095 indicates that the PE VID is invalid. " ::= { hwL2mcCACPortLimitEntry 6 } hwCACPortLimitCeId OBJECT-TYPE SYNTAX VlanIdOrAny MAX-ACCESS not-accessible STATUS current DESCRIPTION "The begin of a CE VID batch. The value ranges from 1 to 4095. The value 4095 indicates that the PE VID is invalid. " ::= { hwL2mcCACPortLimitEntry 7 } hwCACPortLimitCeIdEnd OBJECT-TYPE SYNTAX VlanIdOrAny MAX-ACCESS not-accessible STATUS current DESCRIPTION "The end of a CE VID batch. The value ranges from 1 to 4095. The value 4095 indicates that the PE VID is invalid. " ::= { hwL2mcCACPortLimitEntry 8 } hwCACPortLimitPeerAddress OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS not-accessible STATUS current DESCRIPTION "The peer IP address of a PW interface. The value 0.0.0.0 indicates that the IP address is invalid." ::= { hwL2mcCACPortLimitEntry 9 } hwCACPortLimitVcOrSiteId OBJECT-TYPE SYNTAX Unsigned32(1..4294967295) MAX-ACCESS not-accessible STATUS current DESCRIPTION "The VC ID or SITE ID of a PW interface." ::= { hwL2mcCACPortLimitEntry 10 } hwCACPortLimitChnlName OBJECT-TYPE SYNTAX DisplayString(SIZE (0..31)) MAX-ACCESS not-accessible STATUS current DESCRIPTION "The channel name." ::= { hwL2mcCACPortLimitEntry 11 } hwCACPortLimitAcl OBJECT-TYPE SYNTAX Integer32(0|2000..3999) MAX-ACCESS read-create STATUS current DESCRIPTION "The number of ACL for the multicast groups that do not need to be configured with CAC limit. The ACL number ranges from 2000 to 3999. The default value is 0, indicating that the number is invalid. " ::= { hwL2mcCACPortLimitEntry 12 } hwCACPortLimitMaxEntry OBJECT-TYPE SYNTAX Integer32(0..8000) MAX-ACCESS read-create STATUS current DESCRIPTION "The maximum number of forwarding entries. The value 0 indicates that the number is invalid." ::= { hwL2mcCACPortLimitEntry 13 } hwCACPortLimitEntryCnt OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of current forwarding entries." ::= { hwL2mcCACPortLimitEntry 14 } hwCACPortLimitMaxBandWidth OBJECT-TYPE SYNTAX Integer32(0..4194304) MAX-ACCESS read-create STATUS current DESCRIPTION "The maximum bandwidth. The value 0 indicates that the bandwidth is invalid." ::= { hwL2mcCACPortLimitEntry 15 } hwCACPortLimitBandWidth OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The current bandwidth." ::= { hwL2mcCACPortLimitEntry 16 } hwCACPortLimitCfgRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "The row status." ::= { hwL2mcCACPortLimitEntry 100 } -- -- The hwL2mcQinqGroupSourceLimitInfo group. -- hwL2mcQinqGroupSourceLimitInfo OBJECT IDENTIFIER ::= { hwIgspMibObject 32 } hwL2mcQinqGroupLimitTable OBJECT-TYPE SYNTAX SEQUENCE OF HWL2mcQinqGroupLimitEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table describes the configurations of IGMP snooping group limit on a QinQ interface." ::= { hwL2mcQinqGroupSourceLimitInfo 1 } hwL2mcQinqGroupLimitEntry OBJECT-TYPE SYNTAX HWL2mcQinqGroupLimitEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry is created for each IGMP snooping group limit on a QinQ interface." INDEX { hwL2mcQinqGroupLimitPortType, hwL2mcQinqGroupLimitIfIndex, hwL2mcQinqGroupLimitPeVid, hwL2mcQinqGroupLimitPeVidEnd, hwL2mcQinqGroupLimitCeVid, hwL2mcQinqGroupLimitCeVidEnd } ::= { hwL2mcQinqGroupLimitTable 1 } HWL2mcQinqGroupLimitEntry ::= SEQUENCE { hwL2mcQinqGroupLimitPortType HWPortType, hwL2mcQinqGroupLimitIfIndex InterfaceIndexOrZero, hwL2mcQinqGroupLimitPeVid VlanIdOrAny, hwL2mcQinqGroupLimitPeVidEnd VlanIdOrAny, hwL2mcQinqGroupLimitCeVid VlanIdOrAny, hwL2mcQinqGroupLimitCeVidEnd VlanIdOrAny, hwL2mcQinqGroupLimitNum Unsigned32, hwL2mcQinqGroupLimitRowStatus RowStatus } hwL2mcQinqGroupLimitPortType OBJECT-TYPE SYNTAX HWPortType MAX-ACCESS not-accessible STATUS current DESCRIPTION "The interface type: 1: Invalid 5: Termination sub-interface " ::= { hwL2mcQinqGroupLimitEntry 1 } hwL2mcQinqGroupLimitIfIndex OBJECT-TYPE SYNTAX InterfaceIndexOrZero MAX-ACCESS not-accessible STATUS current DESCRIPTION "The interface index. The value 0 indicates that the interface index is invalid." ::= { hwL2mcQinqGroupLimitEntry 2 } hwL2mcQinqGroupLimitPeVid OBJECT-TYPE SYNTAX VlanIdOrAny MAX-ACCESS not-accessible STATUS current DESCRIPTION "The begin of a PE VID batch. The value ranges from 1 to 4095. The value 4095 indicates that the PE VID is invalid. " ::= { hwL2mcQinqGroupLimitEntry 3 } hwL2mcQinqGroupLimitPeVidEnd OBJECT-TYPE SYNTAX VlanIdOrAny MAX-ACCESS not-accessible STATUS current DESCRIPTION "The end of a PE VID batch. The value ranges from 1 to 4095. The value 4095 indicates that the PE VID is invalid. " ::= { hwL2mcQinqGroupLimitEntry 4 } hwL2mcQinqGroupLimitCeVid OBJECT-TYPE SYNTAX VlanIdOrAny MAX-ACCESS not-accessible STATUS current DESCRIPTION "The begin of a CE VID batch. The value ranges from 1 to 4095. The value 4095 indicates that the CE VID is invalid. " ::= { hwL2mcQinqGroupLimitEntry 5 } hwL2mcQinqGroupLimitCeVidEnd OBJECT-TYPE SYNTAX VlanIdOrAny MAX-ACCESS not-accessible STATUS current DESCRIPTION "The end of a CE VID batch. The value ranges from 1 to 4095. The value 4095 indicates that the CE VID is invalid. " ::= { hwL2mcQinqGroupLimitEntry 6 } hwL2mcQinqGroupLimitNum OBJECT-TYPE SYNTAX Unsigned32(1..16000) MAX-ACCESS read-create STATUS current DESCRIPTION "The group limit number of a QinQ interface." ::= { hwL2mcQinqGroupLimitEntry 10 } hwL2mcQinqGroupLimitRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "The row status." ::= { hwL2mcQinqGroupLimitEntry 100 } hwL2mcQinqSourceLimitTable OBJECT-TYPE SYNTAX SEQUENCE OF HWL2mcQinqSourceLimitEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table describes the configurations of IGMP snooping source limit on a QinQ interface." ::= { hwL2mcQinqGroupSourceLimitInfo 2 } hwL2mcQinqSourceLimitEntry OBJECT-TYPE SYNTAX HWL2mcQinqSourceLimitEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry is created for each IGMP snooping source limit on a QinQ interface." INDEX { hwL2mcQinqSourceLimitPortType, hwL2mcQinqSourceLimitIfIndex, hwL2mcQinqSourceLimitPeVid, hwL2mcQinqSourceLimitPeVidEnd, hwL2mcQinqSourceLimitCeVid, hwL2mcQinqSourceLimitCeVidEnd } ::= { hwL2mcQinqSourceLimitTable 1 } HWL2mcQinqSourceLimitEntry ::= SEQUENCE { hwL2mcQinqSourceLimitPortType HWPortType, hwL2mcQinqSourceLimitIfIndex InterfaceIndexOrZero, hwL2mcQinqSourceLimitPeVid VlanIdOrAny, hwL2mcQinqSourceLimitPeVidEnd VlanIdOrAny, hwL2mcQinqSourceLimitCeVid VlanIdOrAny, hwL2mcQinqSourceLimitCeVidEnd VlanIdOrAny, hwL2mcQinqSourceLimitNum Unsigned32, hwL2mcQinqSourceLimitRowStatus RowStatus } hwL2mcQinqSourceLimitPortType OBJECT-TYPE SYNTAX HWPortType MAX-ACCESS not-accessible STATUS current DESCRIPTION "The interface type: 1: Invalid 5: Termination sub-interface " ::= { hwL2mcQinqSourceLimitEntry 1 } hwL2mcQinqSourceLimitIfIndex OBJECT-TYPE SYNTAX InterfaceIndexOrZero MAX-ACCESS not-accessible STATUS current DESCRIPTION "The interface index. The value 0 indicates that the interface index is invalid." ::= { hwL2mcQinqSourceLimitEntry 2 } hwL2mcQinqSourceLimitPeVid OBJECT-TYPE SYNTAX VlanIdOrAny MAX-ACCESS not-accessible STATUS current DESCRIPTION "The begin of a PE VID batch. The value ranges from 1 to 4095. The value 4095 indicates that the PE VID is invalid. " ::= { hwL2mcQinqSourceLimitEntry 3 } hwL2mcQinqSourceLimitPeVidEnd OBJECT-TYPE SYNTAX VlanIdOrAny MAX-ACCESS not-accessible STATUS current DESCRIPTION "The end of a PE VID batch. The value ranges from 1 to 4095. The value 4095 indicates that the PE VID is invalid. " ::= { hwL2mcQinqSourceLimitEntry 4 } hwL2mcQinqSourceLimitCeVid OBJECT-TYPE SYNTAX VlanIdOrAny MAX-ACCESS not-accessible STATUS current DESCRIPTION "The begin of a CE VID batch. The value ranges from 1 to 4095. The value 4095 indicates that the CE VID is invalid. " ::= { hwL2mcQinqSourceLimitEntry 5 } hwL2mcQinqSourceLimitCeVidEnd OBJECT-TYPE SYNTAX VlanIdOrAny MAX-ACCESS not-accessible STATUS current DESCRIPTION "The end of a CE VID batch. The value ranges from 1 to 4095. The value 4095 indicates that the CE VID is invalid. " ::= { hwL2mcQinqSourceLimitEntry 6 } hwL2mcQinqSourceLimitNum OBJECT-TYPE SYNTAX Unsigned32(1..16000) MAX-ACCESS read-create STATUS current DESCRIPTION "The source number of a QinQ interface." ::= { hwL2mcQinqSourceLimitEntry 10 } hwL2mcQinqSourceLimitRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "The row status." ::= { hwL2mcQinqSourceLimitEntry 100 } -- -- Conformance Information -- hwL2mcMibConformance OBJECT IDENTIFIER ::= { hwL2MultiCastMIB 100 } hwL2mcMibCompliances OBJECT IDENTIFIER ::= { hwL2mcMibConformance 1 } hwL2mcMibGroups OBJECT IDENTIFIER ::= { hwL2mcMibConformance 2 } hwIgspMibCompliance MODULE-COMPLIANCE STATUS current DESCRIPTION "The compliance statement for device supporting IGMP Snooping." MODULE MANDATORY-GROUPS{ hwIgspSystemInfoGroup, hwL2mcCfgInfoGroup, hwL2mcStatisticsInfoGroup, hwL2mcFwdInfoGroup, hwL2mcGroupInfoGroup, hwL2mcGroupCfgInfoGroup, hwL2mcSsmSourceInfoGroup, hwL2mcPortGroupPolicyCfgInfoGroup, hwL2mcChnlCfgInfoGroup, hwL2mcLimitInfoGroup, hwL2mcPortLimitInfoGroup, hwL2mcFastChnlCfgInfoGroup, hwL2mcRouterPortInfoGroup, hwL2mcRouterPortCfgInfoGroup, hwL2mcChnlGroupCfgInfoGroup, hwL2mcGroupPolicyCfgInfoGroup, hwL2mcChnlDenyCfgInfoGroup, hwL2mcQinQPortInfoGroup, hwL2mcETrackingInfoInfoGroup, hwL2mcSourceGroupInfoGroup, hwL2mcDTFwdInfoGroup, hwL2mcDTGroupInfoGroup, hwL2mcMulticastTrafficPolicyCfgInfoGroup, hwL2mcRouteLearnDisablePolicyCfgInfoGroup, hwL2mcTrackVRRPCfgInfoGroup } ::= { hwL2mcMibCompliances 1 } hwIgspSystemInfoGroup OBJECT-GROUP OBJECTS { hwIgmpSnoopingEnabled, hwSendQueryEnabled, hwSendQuerySourceIpAddr, hwL2mcCacTrapInterval, hwL2mcPerformanceStatisticsInterval } STATUS current DESCRIPTION "." ::= { hwL2mcMibGroups 1 } hwL2mcCfgInfoGroup OBJECT-GROUP OBJECTS { hwL2mcEnabled, hwL2mcRouterAgingTime, hwL2mcMaxQueryRespTime, hwL2mcLastMemQueryInterval, hwL2mcQueryInterval, hwL2mcRobustCount, hwL2mcCheckRouterAlert, hwL2mcSendRouterAlert, hwL2mcIgmpVersion, hwL2mcFwdMode, hwL2mcPromptLeaveEnable, hwL2mcPromptLeaveAclNum, hwL2mcRouterPortLearningEnable, hwL2mcReportSuppressEnable, hwL2mcIgmpQuerierEnable, hwL2mcIgmpSsmMappingEnable, hwL2mcSsmAclNum, hwL2mcProxyRouterProtocolPass, hwL2mcAsmSsmFlag, hwL2mcSrcLifeTime, hwL2mcPerformanceStatistics, hwL2mcQuerierElection, hwETrackEnable, hwL2mcBackupQueryFwd, hwL2mcBackupReportFwd, hwL2mcQuerySuppress, hwL2mcRtLearnRingLinkage, hwL2mcRowStatus } STATUS current DESCRIPTION "." ::= { hwL2mcMibGroups 2 } hwL2mcStatisticsInfoGroup OBJECT-GROUP OBJECTS { hwL2mcRecvIgmpV1ReportNum, hwL2mcRecvIgmpV2ReportNum, hwL2mcRecvIgmpV3ReportNum, hwL2mcRecvIgmpLeaveNum, hwL2mcRecvIgmpV1QueryNum, hwL2mcRecvIgmpV2QueryNum, hwL2mcRecvIgmpV3QueryNum, hwL2mcRecvPimHelloNum, hwL2mcSendQueryNum, hwL2mcSendQuerySourceNum, hwL2mcProxyGenQueryNum, hwL2mcProxyGroupQueryNum, hwL2mcProxyGroupSourceQueryNum, hwL2mcIgmpPacketClearStats } STATUS current DESCRIPTION "." ::= { hwL2mcMibGroups 3 } hwL2mcFwdInfoGroup OBJECT-GROUP OBJECTS { hwL2mcFwdAddressType, hwL2mcFwdHostFlag1, hwL2mcFwdHostFlag2, hwL2mcFwdHostFlag3, hwL2mcFwdHostFlag4 } STATUS current DESCRIPTION "." ::= { hwL2mcMibGroups 4 } hwL2mcGroupInfoGroup OBJECT-GROUP OBJECTS { hwL2mcSourceUpTime, hwL2mcSourceExpires, hwL2mcGroupUpTime, hwL2mcGroupExpires, hwL2mcGroupFilterFlag, hwL2mcGroupHostFlag1, hwL2mcGroupHostFlag2, hwL2mcGroupRowStatus } STATUS current DESCRIPTION "." ::= { hwL2mcMibGroups 5 } hwL2mcGroupCfgInfoGroup OBJECT-GROUP OBJECTS { hwGroupCfgRowStatus } STATUS current DESCRIPTION "." ::= { hwL2mcMibGroups 6 } hwL2mcSsmSourceInfoGroup OBJECT-GROUP OBJECTS { hwL2mcSsmSourceRowStatus } STATUS current DESCRIPTION "." ::= { hwL2mcMibGroups 7 } hwL2mcPortGroupPolicyCfgInfoGroup OBJECT-GROUP OBJECTS { hwPortGroupPolicyAclNum, hwPortGroupPolicyIgmpVersion, hwPortGroupPolicyRowStatus } STATUS current DESCRIPTION "." ::= { hwL2mcMibGroups 8 } hwL2mcChnlCfgInfoGroup OBJECT-GROUP OBJECTS { hwChnlCfgChnlType, hwChnlCfgRowStatus } STATUS current DESCRIPTION "." ::= { hwL2mcMibGroups 9 } hwL2mcLimitInfoGroup OBJECT-GROUP OBJECTS { hwL2mcLimitMaxEntry, hwL2mcLimitEntryCnt, hwL2mcLimitMaxBandWidth, hwL2mcLimitBandWidth, hwL2mcLimitAcl, hwL2mcLimitCfgRowStatus } STATUS current DESCRIPTION "." ::= { hwL2mcMibGroups 10 } hwL2mcPortLimitInfoGroup OBJECT-GROUP OBJECTS { hwPortLimitAcl, hwPortLimitMaxEntry, hwPortLimitEntryCnt, hwPortLimitMaxBandWidth, hwPortLimitBandWidth, hwPortLimitCfgRowStatus } STATUS current DESCRIPTION "." ::= { hwL2mcMibGroups 11 } hwL2mcFastChnlCfgInfoGroup OBJECT-GROUP OBJECTS { hwL2mcFastChnlCfgRowStatus } STATUS current DESCRIPTION "." ::= { hwL2mcMibGroups 12 } hwL2mcRouterPortInfoGroup OBJECT-GROUP OBJECTS { hwL2mcRouterPortGroupUpTime, hwL2mcRouterPortGroupExpires, hwL2mcRouterPortGroupHostFlag1 } STATUS current DESCRIPTION "." ::= { hwL2mcMibGroups 13 } hwL2mcRouterPortCfgInfoGroup OBJECT-GROUP OBJECTS { hwL2mcRouterPortCfgRowStatus } STATUS current DESCRIPTION "." ::= { hwL2mcMibGroups 14 } hwL2mcChnlGroupCfgInfoGroup OBJECT-GROUP OBJECTS { hwChnlGroupCfgPerBand, hwChnlGroupCfgRowStatus } STATUS current DESCRIPTION "." ::= { hwL2mcMibGroups 15 } hwL2mcGroupPolicyCfgInfoGroup OBJECT-GROUP OBJECTS { hwGroupPolicyAclNum, hwGroupPolicyIgmpVersion, hwGroupPolicyRowStatus } STATUS current DESCRIPTION "." ::= { hwL2mcMibGroups 16} hwL2mcChnlDenyCfgInfoGroup OBJECT-GROUP OBJECTS { hwChnlDenyCfg , hwChnlDenyCfgRowStatus } STATUS current DESCRIPTION "." ::= { hwL2mcMibGroups 17} hwL2mcQinQPortInfoGroup OBJECT-GROUP OBJECTS { hwQinQPortTime , hwQinQPortFlag } STATUS current DESCRIPTION "." ::= { hwL2mcMibGroups 18} hwL2mcETrackingInfoInfoGroup OBJECT-GROUP OBJECTS { hwETrackInfoFlag } STATUS current DESCRIPTION "." ::= { hwL2mcMibGroups 19} hwL2mcSourceGroupInfoGroup OBJECT-GROUP OBJECTS { hwL2mcSourceGroupStat } STATUS current DESCRIPTION "." ::= { hwL2mcMibGroups 22} hwL2mcDTFwdInfoGroup OBJECT-GROUP OBJECTS { hwL2mcDTFwdAddressType, hwL2mcDTFwdHostFlag1, hwL2mcDTFwdHostFlag2, hwL2mcDTFwdHostFlag3, hwL2mcDTFwdHostFlag4 } STATUS current DESCRIPTION "." ::= { hwL2mcMibGroups 23 } hwL2mcDTGroupInfoGroup OBJECT-GROUP OBJECTS { hwL2mcDTSourceUpTime, hwL2mcDTSourceExpires, hwL2mcDTGroupUpTime, hwL2mcDTGroupExpires, hwL2mcDTGroupHostFlag1, hwL2mcDTGroupHostFlag2, hwL2mcDTGroupRowStatus } STATUS current DESCRIPTION "." ::= { hwL2mcMibGroups 24 } hwL2mcMulticastTrafficPolicyCfgInfoGroup OBJECT-GROUP OBJECTS { hwMulticastTrafficPolicyRowStatus } STATUS current DESCRIPTION "." ::= { hwL2mcMibGroups 25 } hwL2mcRouteLearnDisablePolicyCfgInfoGroup OBJECT-GROUP OBJECTS { hwRouteLearnDisablePolicyRowStatus } STATUS current DESCRIPTION "." ::= { hwL2mcMibGroups 26 } hwL2mcTrackVRRPCfgInfoGroup OBJECT-GROUP OBJECTS { hwTrackVRRPVridIfIndex, hwTrackVRRPVridID, hwTrackVRRPRowStatus } STATUS current DESCRIPTION "." ::= { hwL2mcMibGroups 27 } END