-- ============================================================================= -- Copyright (C) 2002-2003 by HUAWEI TECHNOLOGIES. All rights reserved. -- -- Description:MPLS-BGP-VPN-MIB -- Reference:This mib was extracted from Draft-ietf-mpls-ldp-mib-01 -- Version: V1.3 -- History: -- VERSION AUTHOR/ Change Description -- OLD/NEW DATE -- -- #/1.1 Lingesh M + Initial create. -- 27/08/99 -- #/1.2 27/09/99 + Replaced the MIB objects -- - hwMplsLdpLsrMaxIngressCrlspTnls -- - hwMplsLdpLsrMaxInbetwnCrlspTnls -- with hwMplsLdpLsrMaxCrlspTnls -- 1.2/1.3 19/10/99 + Added hwMplsLdpPeerType in Peer Table. -- 04/10/99 + Added hwMplsLdpEntityIfTable. -- 1.3/1.4 23/11/99 + Added mib object for Hello Hold Time in Entity -- Table, modified Cr-lsp Tnl index of type -- read-create to not-accessible. -- + Removed hwMplsLdpSessionRowStatus mib-object. -- -- 1.1 03/01/2k + Huawei MPLS Release 1.0.0.0 -- Naren -- -- 1.2 27/01/2k + Modified for MPLS Implementation for Huawei -- Naren Following objects are added in the Incarnation table -- hwMplsLdpLsrMaxVcmCapability -- hwMplsLdpLsrVcmPathVecInAllLblMapPresent -- hwMplsLdpLsrRequestRetrytimerValue -- hwMplsLdpLsrNumOfRequestRetryAttempts -- Following Notifications are added -- hwMplsLdpIncarnUpEventFailure -- hwMplsLdpIncarnDownEventFailure -- hwMplsLdpEntityUpEventFailure -- hwMplsLdpEntityDownEventFailure -- -- 1.3 03/04/2k + Changed FS related identification to hw -- David related identification. -- 1.4 03/14/2003 add hwMplsLdpSessionUpEventFailure and hwMplsLdpSessionDownEventFailure -- ==================================================================================== -- -- Full Copyright Notice of the mib that was extracted from Draft-ietf-mpls-ldp-mib-01 as follows: -- --Copyright (C) The Internet Society (1999). All Rights Reserved. -- -- -- This document and translations of it may be copied and furnished to -- others, and derivative works that comment on or otherwise explain it -- or assist in its implementation may be prepared, copied, published -- and distributed, in whole or in part, without restriction of any -- kind, provided that the above copyright notice and this paragraph are -- included on all such copies and derivative works. However, this -- document itself may not be modified in any way, such as by removing -- the copyright notice or references to the Internet Society or other -- Internet organizations, except as needed for the purpose of -- developing Internet standards in which case the procedures for -- copyrights defined in the Internet Standards process must be -- followed, or as required to translate it into languages other than -- English. -- -- The limited permissions granted above are perpetual and will not be -- revoked by the Internet Society or its successors or assigns. -- -- This document and the information contained herein is provided on an -- "AS IS" basis and THE INTERNET SOCIETY AND THE INTERNET ENGINEERING -- TASK FORCE DISCLAIMS ALL WARRANTIES, EXPRESS OR IMPLIED, INCLUDING -- BUT NOT LIMITED TO ANY WARRANTY THAT THE USE OF THE INFORMATION -- HEREIN WILL NOT INFRINGE ANY RIGHTS OR ANY IMPLIED WARRANTIES OF -- MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE. -- -- HuaweiMPLS Label Distribution Protocol MIB Definitions HUAWEI-MPLS-LDP-MIB DEFINITIONS ::= BEGIN IMPORTS huaweiMgmt FROM HUAWEI-3COM-OID-MIB OBJECT-TYPE, MODULE-IDENTITY, NOTIFICATION-TYPE, Integer32, Counter32, Unsigned32,IpAddress FROM SNMPv2-SMI MODULE-COMPLIANCE, OBJECT-GROUP, NOTIFICATION-GROUP FROM SNMPv2-CONF TEXTUAL-CONVENTION, TruthValue, RowStatus, TimeInterval FROM SNMPv2-TC; hwMplsLdp MODULE-IDENTITY LAST-UPDATED "9906301200Z" -- June 30, 1999 ORGANIZATION "HuaweiMPLS Working Group" CONTACT-INFO "S. Manikantan, Huawei Software Pvt. Ltd., 481, Mount Road, Nandanam. CHENNAI-35 INDIA manis@Huawei.futsoft.com" DESCRIPTION "All rights reserved" REVISION "9611082155Z" DESCRIPTION "The MIB for HuaweiMPLS LDP module. This MIB has been derived from the MPLS Working group LDP MIB and MPLS Working group TE MIB ." ::= { hwMpls 2} hwMpls OBJECT IDENTIFIER ::= { huaweiMgmt 12 } --******************************************************************** -- MPLS LDP Textual Conventions --******************************************************************** -- DisplayString ::= OCTET STRING -- This data type is used to model textual information taken -- from the NVT ASCII character set. By convention, objects -- with this syntax are declared as having -- (SIZE (0..255)) PhysAddress ::= OCTET STRING -- This data type is used to model media addresses. For many -- types of media, this will be in a binary representation. -- For example, an ethernet address would be represented as -- a string of 6 octets. BitRate ::= INTEGER BurstSize ::= INTEGER MplsLsrIdentifier ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "The Label Switch Router (LSR) identifier is the first 4 bytes or the IP Address component of the Label Distribution Protocol (LDP) identifier." SYNTAX OCTET STRING (SIZE (4)) MplsLdpGenAddr ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "The value of an network layer or data link layer address." SYNTAX OCTET STRING (SIZE (0..64)) MplsLdpIdentifier ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "The LDP identifier is a six octet quantity which is used to identify an Label Switch Router (LSR) label space. The first four octets encode an IP address assigned to the LSR, and the last two octets identify a specific label space within the LSR." SYNTAX OCTET STRING (SIZE (6)) AtmVpIdentifier ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "The VPI value for a VPL. The value VPI=0 is not used for a VPL not associated with a VCL. For ATM UNIs supporting VPCs the VPI value ranges from 1 to 255. For ATM UNIs supporting VCCs the VPI value ranges from 0 to 255. The maximum VPI value cannot exceed the value allowable by atmInterfaceMaxVpiBits defined in ATM-MIB." SYNTAX INTEGER (0..4095) AtmVcIdentifier ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "The VCI value for a VCL. The maximum VCI value cannot exceed the value allowable by atmInterfaceMaxVciBits defined in ATM-MIB." SYNTAX INTEGER (0..65535) AddressFamilyNumbers ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "An address family. Values are defined in RFC 1700 - Assigned Numbers. All values may not be relevant in all contexts when used in this MIB, but are included for completeness." REFERENCE "RFC 1700 Assigned Numbers, Reynolds and Postel, Oct. 1994" SYNTAX INTEGER { other(0), ipv4(1), ipv6(2), nsap(3), hdlc(4), bbn1822(5), ieee802(6), e163(7), e164(8), f69(9), x121(10), ipx(11), appleTalk(12), decnetIV(13), banyanVines(14), e164WithNsap(15) } MplsLabel ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "Represents an MPLS label. Note that the contents of a label field are interpreted in an interface-type specific fashion. For example, the label carried in the MPLS shim header is 20 bits wide and the top 12 bits must be zero. The frame relay label can be either 10, 17 or 23 bits wide depending on the size of the DLCI field size and the top 22, 15, or 9 bits must be zero, respectively. For an ATM interface, the lowermost 16 bits are interpreted as the VCI, the next 8 bits as the VPI and the remaining bits must be zero. Also note the permissible label values are also a function of the interface type. For example, the value 3 has special semantics in the control plane for an MPLS shim header label and is not a valid label value in the datapath." REFERENCE "1. MPLS Label Stack Encoding, Rosen et al, draft- ietf-mpls-label-encaps-04.txt, April 1999. 2. Use of Label Switching on Frame Relay Networks, Conta et al, draft-ietf-mpls-fr-03.txt, Nov. 1998." SYNTAX INTEGER MplsTunnelIndex ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "Index into mplsTunnelTable." SYNTAX INTEGER (0..65535) hwMplsLdpObjects OBJECT IDENTIFIER ::= { hwMplsLdp 1 } hwMplsLdpNotifications OBJECT IDENTIFIER ::= { hwMplsLdp 2 } --**************************************************************** -- MPLS LDP Objects --**************************************************************** hwMplsLdpLsrObjects OBJECT IDENTIFIER ::= { hwMplsLdpObjects 1 } hwMplsLdpEntityObjects OBJECT IDENTIFIER ::= { hwMplsLdpObjects 2 } hwMplsLdpPeerObjects OBJECT IDENTIFIER ::= { hwMplsLdpObjects 3 } hwMplsLdpSessionObjects OBJECT IDENTIFIER ::= { hwMplsLdpObjects 4 } hwMplsLdpHelloAdjacencyObjects OBJECT IDENTIFIER ::= { hwMplsLdpObjects 5 } hwMplsLdpCrlspTnlObjects OBJECT IDENTIFIER ::= { hwMplsLdpObjects 6 } -- -- The MPLS Label Distribution Protocol Label Switch Router Objects -- hwMplsLdpLsrIncarnTable OBJECT-TYPE SYNTAX SEQUENCE OF HwMplsLdpLsrIncarnEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "HuaweiMPLS provides support for multiple incarnations of the MPLS Stack in a target. The LSR defined in the standard MIB is treated as an incarnation in this MIB. Using a local policy the Network administrator must group the LDP Entities that should be placed in an incarnation." ::= { hwMplsLdpLsrObjects 1 } hwMplsLdpLsrIncarnEntry OBJECT-TYPE SYNTAX HwMplsLdpLsrIncarnEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in this table represents an LSR incarnation. All the entries in this table are created initially when the LDP is initiated. The row status of each entry will be in 'notInService' state initially. The row status must be set to 'active' after the necessary configurations are complete with respect to an incarnation. Currenlty the LSR ID of the incarnation is the only mandatory parameter that must be set before the rowStatus is set to 'active'. An LSR Incarnation Entity is uniquely indexed by its Incarnation Identifier." INDEX { hwMplsLdpLsrIncarnID } ::= { hwMplsLdpLsrIncarnTable 1 } HwMplsLdpLsrIncarnEntry ::= SEQUENCE { hwMplsLdpLsrID MplsLsrIdentifier, hwMplsLdpLsrLoopDetectionPresent TruthValue, hwMplsLdpLsrLoopDetectionAdminStatus INTEGER, hwMplsLdpLsrPathVectorLimit INTEGER, hwMplsLdpLsrHopCountLimit INTEGER, hwMplsLdpLsrLoopPreventionPresent TruthValue, hwMplsLdpLsrLoopPreventionAdminStatus INTEGER, hwMplsLdpLsrLabelRetentionMode INTEGER, hwMplsLdpLsrIncarnID INTEGER, hwMplsLdpLsrMaxLdpEntities INTEGER, hwMplsLdpLsrMaxLocalPeers INTEGER, hwMplsLdpLsrMaxRemotePeers INTEGER, hwMplsLdpLsrMaxIfaces INTEGER, hwMplsLdpLsrMaxLsps INTEGER, hwMplsLdpLsrMaxCrlspTnls INTEGER, hwMplsLdpLsrMaxErhopPerCrlspTnl INTEGER, hwMplsLdpLsrRowStatus RowStatus, hwMplsLdpLsrMaxVcmCapability INTEGER, hwMplsLdpLsrVcmPathVecInAllLblMapPresent TruthValue, hwMplsLdpLsrRequestRetrytimerValue INTEGER, hwMplsLdpLsrNumOfRequestRetryAttempts INTEGER } hwMplsLdpLsrID OBJECT-TYPE SYNTAX MplsLsrIdentifier MAX-ACCESS read-write STATUS current DESCRIPTION "The LSR's Identifier." ::= { hwMplsLdpLsrIncarnEntry 1 } hwMplsLdpLsrLoopDetectionPresent OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION "A indication of whether this LSR supports loop detection. A value of 'true' indicates this LSR does support loop detection. A value of 'false' indicates this LSR does not support loop detection." DEFVAL { true } ::= { hwMplsLdpLsrIncarnEntry 2 } hwMplsLdpLsrLoopDetectionAdminStatus OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "To enable loop detection the value of this object should be 'enabled(1)'. Otherwise, to turn off loop detection, set this value to 'disabled(2)'." DEFVAL { enabled } ::= { hwMplsLdpLsrIncarnEntry 3 } hwMplsLdpLsrPathVectorLimit OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION "This object only has meaning if hwMplsLdpLsrLoopDetectionPresent has the value of 'true'. The value of this object represents the limit of path vectors which this LSR uses to treat the message as if it had traversed a loop." DEFVAL { 32 } ::= { hwMplsLdpLsrIncarnEntry 4 } hwMplsLdpLsrHopCountLimit OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION "This object only has meaning if hwMplsLdpLsrLoopDetectionPresent has the value of 'true'. The value of this object represents the limit on the Hop Count which this LSR uses to treat the message as if it had traversed a loop." DEFVAL { 255 } ::= { hwMplsLdpLsrIncarnEntry 5 } hwMplsLdpLsrLoopPreventionPresent OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION "A indication of whether this LSR supports loop prevention. A value of 'true' indicates this LSR does support loop prevention. A value of 'false' indicates this LSR does not support loop prevention. Current release of HuaweiMPLS does not provide support to assign this MIB object with a value 'true'." DEFVAL { false } ::= { hwMplsLdpLsrIncarnEntry 6 } hwMplsLdpLsrLoopPreventionAdminStatus OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "To enable loop prevention the value of this object should be 'enabled(1)'. Otherwise, to turn off loop prevention, set this value to 'disabled(2)'. Current release of HuaweiMPLS does not provide support to assign this MIB object with a value 'enabled'." DEFVAL { disabled } ::= { hwMplsLdpLsrIncarnEntry 7 } hwMplsLdpLsrLabelRetentionMode OBJECT-TYPE SYNTAX INTEGER { conservative(1), liberal(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "The LSR can be configured to use either conservative or liberal label retention mode. If the value of this object is conservative(1) then advertized label mappings are retained only if they will be used to forward packets, i.e. if label came from a valid next hop. If the value of this object is liberal(2) then all advertized label mappings are retained whether they are from a valid next hop or not. Current release of HuaweiMPLS does not provide support to assign this MIB object with a value 'liberal'." DEFVAL { conservative } ::= { hwMplsLdpLsrIncarnEntry 8 } hwMplsLdpLsrIncarnID OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-only STATUS current DESCRIPTION "The incarnation acts as index to all the elements in this table." ::= { hwMplsLdpLsrIncarnEntry 9 } hwMplsLdpLsrMaxLdpEntities OBJECT-TYPE SYNTAX INTEGER (1..1024) MAX-ACCESS read-write STATUS current DESCRIPTION "The maximum number of LDP entities that can be supported by this Incarnation." ::= { hwMplsLdpLsrIncarnEntry 10 } hwMplsLdpLsrMaxLocalPeers OBJECT-TYPE SYNTAX INTEGER (1..1024) MAX-ACCESS read-write STATUS current DESCRIPTION "The maximum number of Local LDP peers that can be supported by this Incarnation." ::= { hwMplsLdpLsrIncarnEntry 11 } hwMplsLdpLsrMaxRemotePeers OBJECT-TYPE SYNTAX INTEGER (1..1024) MAX-ACCESS read-write STATUS current DESCRIPTION "The maximum number of Remote LDP peers that can be supported by this Incarnation." ::= { hwMplsLdpLsrIncarnEntry 12 } hwMplsLdpLsrMaxIfaces OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION "The maximum number of Label enabled Interfaces that can be supported by this Incarnation." ::= { hwMplsLdpLsrIncarnEntry 13 } hwMplsLdpLsrMaxLsps OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION "The maximum number of Label Switched Paths that can be supported by this Incarnation." ::= { hwMplsLdpLsrIncarnEntry 14 } hwMplsLdpLsrMaxCrlspTnls OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION "The maximum number of CRLSPs that can be supported by this Incarnation." ::= { hwMplsLdpLsrIncarnEntry 15 } hwMplsLdpLsrMaxErhopPerCrlspTnl OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION " The maximum number of ER-Hops that can be supported in a CRLSP tunnel." ::= { hwMplsLdpLsrIncarnEntry 16 } hwMplsLdpLsrRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "An object that allows entries in this table to be created and deleted using the RowStatus convention." ::= { hwMplsLdpLsrIncarnEntry 17 } hwMplsLdpLsrMaxVcmCapability OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION " " ::= { hwMplsLdpLsrIncarnEntry 18 } hwMplsLdpLsrVcmPathVecInAllLblMapPresent OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION " " ::= { hwMplsLdpLsrIncarnEntry 19 } hwMplsLdpLsrRequestRetrytimerValue OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION " " ::= { hwMplsLdpLsrIncarnEntry 20 } hwMplsLdpLsrNumOfRequestRetryAttempts OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-write STATUS current DESCRIPTION " " ::= { hwMplsLdpLsrIncarnEntry 21 } -- -- The MPLS Label Distribution Protocol Entity Table -- hwMplsLdpEntityTable OBJECT-TYPE SYNTAX SEQUENCE OF HwMplsLdpEntityEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains information about the MPLS Label Distribution Protocol Entities which exist on this Label Switch Router (LSR)." ::= { hwMplsLdpEntityObjects 1 } hwMplsLdpEntityEntry OBJECT-TYPE SYNTAX HwMplsLdpEntityEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in this table represents an LDP entity. An entry can be created by a network administrator or by an SNMP agent as instructed by LDP. An LPD Entity is uniquely indexed by its LPD Identifier." INDEX { hwMplsLdpLsrIncarnID, hwMplsLdpEntityIfIndex } ::= { hwMplsLdpEntityTable 1 } HwMplsLdpEntityEntry ::= SEQUENCE { hwMplsLdpEntityID MplsLdpIdentifier, hwMplsLdpEntityLabelSpaceType INTEGER, hwMplsLdpEntityDefVpi AtmVpIdentifier, hwMplsLdpEntityDefVci AtmVcIdentifier, hwMplsLdpEntityUnlabTrafVpi AtmVpIdentifier, hwMplsLdpEntityUnlabTrafVci AtmVcIdentifier, hwMplsLdpEntityMergeCapability INTEGER, hwMplsLdpEntityVcDirectionality INTEGER, hwMplsLdpEntityWellKnownDiscoveryPort INTEGER, hwMplsLdpEntityMtu INTEGER, hwMplsLdpEntityKeepAliveHoldTimer INTEGER, hwMplsLdpEntityFailedInitSessionThreshold INTEGER, hwMplsLdpEntityLabelDistributionMethod INTEGER, hwMplsLdpEntityLabelAllocationMethod INTEGER, hwMplsLdpEntityHelloHoldTimer INTEGER, hwMplsLdpEntityRowStatus RowStatus } hwMplsLdpEntityID OBJECT-TYPE SYNTAX MplsLdpIdentifier MAX-ACCESS accessible-for-notify STATUS current DESCRIPTION "The LDP identifier which uniquely identifies the LDP Entity. This is s six octet quantity which is used to identify an Label Switch Router (LSR) label space. The first four octets encode an IP address assigned to the LSR, and the last two octets identify a specific label space within the LSR." REFERENCE "LDP Specification, Section on LDP Identifiers." ::= { hwMplsLdpEntityEntry 1 } hwMplsLdpEntityLabelSpaceType OBJECT-TYPE SYNTAX INTEGER { unknown(1), perInterface(2), perPlatform(3) } MAX-ACCESS read-create STATUS current DESCRIPTION "The type of label spaces associated with this LDP Entity. The values are 'unknown(1)' The type of label space is not known. 'perInterface(2)' The type of label space is tied to an interface. 'perPlatform(3)' The type of label space is tied to the platform." REFERENCE "LDP Specification, Section on Label Spaces." ::= { hwMplsLdpEntityEntry 2 } hwMplsLdpEntityDefVpi OBJECT-TYPE SYNTAX AtmVpIdentifier MAX-ACCESS read-create STATUS current DESCRIPTION "The Default VPI value used in the label for the default VPI." ::= { hwMplsLdpEntityEntry 3 } hwMplsLdpEntityDefVci OBJECT-TYPE SYNTAX AtmVcIdentifier MAX-ACCESS read-create STATUS current DESCRIPTION "The Default VCI value used in the label for the default VCI." ::= { hwMplsLdpEntityEntry 4 } hwMplsLdpEntityUnlabTrafVpi OBJECT-TYPE SYNTAX AtmVpIdentifier MAX-ACCESS read-create STATUS current DESCRIPTION "VPI value of the VCC supporting unlabeled traffic." DEFVAL { 0 } ::= { hwMplsLdpEntityEntry 5 } hwMplsLdpEntityUnlabTrafVci OBJECT-TYPE SYNTAX AtmVcIdentifier MAX-ACCESS read-create STATUS current DESCRIPTION "VCI value of the VCC supporting unlabeled traffic." DEFVAL { 32 } ::= { hwMplsLdpEntityEntry 6 } hwMplsLdpEntityMergeCapability OBJECT-TYPE SYNTAX INTEGER { noMerge(0), vpMerge(1), vcMerge(2), vpVcMerge(3) } MAX-ACCESS read-create STATUS current DESCRIPTION "Sets the merge capability for this LDP entity. Current Release of HuaweiMPLS does not provide support for any kind of Merge." REFERENCE "draft-ietf-mpls-ldp-04.txt, Section 3.5.3" ::= { hwMplsLdpEntityEntry 7 } hwMplsLdpEntityVcDirectionality OBJECT-TYPE SYNTAX INTEGER { bidirectional(1), unidirectional(2) } MAX-ACCESS read-create STATUS current DESCRIPTION "Sets the VC directionality for this LDP entity." REFERENCE "draft-ietf-mpls-ldp-04.txt, Section 3.5.3" ::= { hwMplsLdpEntityEntry 8 } hwMplsLdpEntityWellKnownDiscoveryPort OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-create STATUS current DESCRIPTION "The well known LDP Discovery Port." ::= { hwMplsLdpEntityEntry 9 } hwMplsLdpEntityMtu OBJECT-TYPE SYNTAX INTEGER (0..65535) MAX-ACCESS read-create STATUS current DESCRIPTION "The maximum transmission unit (MTU) that was configured for this entity." ::= { hwMplsLdpEntityEntry 10 } hwMplsLdpEntityKeepAliveHoldTimer OBJECT-TYPE SYNTAX INTEGER (1..65535) UNITS "seconds" MAX-ACCESS read-create STATUS current DESCRIPTION "The two octet value which is the proposed keep alive hold timer for this LDP Entity." ::= { hwMplsLdpEntityEntry 11 } hwMplsLdpEntityFailedInitSessionThreshold OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS read-create STATUS current DESCRIPTION "When attempting to establish a session with a given Peer, the given LDP Entity should send out a notification when exceeding this threshold. A value of 0 (zero) for this object indicates that the threshold is infinity. In other words, a notification will not be sent if the value of this object is 0 (zero)." ::= { hwMplsLdpEntityEntry 12 } hwMplsLdpEntityLabelDistributionMethod OBJECT-TYPE SYNTAX INTEGER { downstreamOnDemand(1), downstreamUnsolicited(2) } MAX-ACCESS read-create STATUS current DESCRIPTION "For any given LDP session, the method of label distribution must be specified. Current release of HuaweiMPLS does not provide support for 'downstreamUnsolicited'." REFERENCE "draft-ietf-mpls-arch-04.txt [20]." ::= { hwMplsLdpEntityEntry 13 } hwMplsLdpEntityLabelAllocationMethod OBJECT-TYPE SYNTAX INTEGER { ordered(1), independent(2) } MAX-ACCESS read-create STATUS current DESCRIPTION "For any given LDP session, the method of label allocation must be specified. Label can be allocated in either ordered mode or in the independent mode." DEFVAL { ordered } ::= { hwMplsLdpEntityEntry 14 } hwMplsLdpEntityHelloHoldTimer OBJECT-TYPE SYNTAX INTEGER (1..65535) UNITS "seconds" MAX-ACCESS read-create STATUS current DESCRIPTION "The two octet value which is the proposed hello hold timer for this LDP Entity." ::= { hwMplsLdpEntityEntry 15 } hwMplsLdpEntityRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "An object that allows entries in this table to be created and deleted using the RowStatus convention." ::= { hwMplsLdpEntityEntry 16 } -- -- The MPLS LDP Entity Interface Table -- hwMplsLdpEntityIfTable OBJECT-TYPE SYNTAX SEQUENCE OF HwMplsLdpEntityIfEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains information about the interfaces that are associated with an LDP Entity. There should be atleast one interface associated with each LDP Entity. If the LDP Entity supports 'per interface based label space' label type then, atmost one interface can be associated with the LDP entity. If the LDP Entity supports 'per platform based label space' label type then, more than one interface can be associated with the LDP Entity." ::= { hwMplsLdpEntityObjects 2 } hwMplsLdpEntityIfEntry OBJECT-TYPE SYNTAX HwMplsLdpEntityIfEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in this table represents an Interface that is associated with a LDP entity. An entry can be created by a network administrator or by an SNMP agent as instructed by LDP. An interface (row in this table) can be created/deleted only when the associted LDP Entity row status has the value notInService or notReady." INDEX { hwMplsLdpLsrIncarnID, hwMplsLdpEntityIfIndex } ::= { hwMplsLdpEntityIfTable 1 } HwMplsLdpEntityIfEntry ::= SEQUENCE { hwMplsLdpEntityIfIndex INTEGER, hwMplsLdpEntityIfIpv4Address IpAddress, hwMplsLdpEntityIfRowStatus RowStatus } hwMplsLdpEntityIfIndex OBJECT-TYPE SYNTAX INTEGER (1..4294967295) MAX-ACCESS not-accessible STATUS current DESCRIPTION "Identifier that uniquely identifies the Interface with respect to an LDP Entity. The ifIndex value corresponds to the IfIndex value of the MIB-II" ::= { hwMplsLdpEntityIfEntry 1 } hwMplsLdpEntityIfIpv4Address OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-create STATUS current DESCRIPTION "The IPv4 address associated with the interface." ::= { hwMplsLdpEntityIfEntry 2 } hwMplsLdpEntityIfRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "An object that allows entries in this table to be created and deleted using the RowStatus convention." ::= { hwMplsLdpEntityIfEntry 3 } -- -- The MPLS LDP Entity Configurable ATM Label Range Table -- hwMplsLdpEntityConfAtmLabelRangeTable OBJECT-TYPE SYNTAX SEQUENCE OF HwMplsLdpEntityConfAtmLabelRangeEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The MPLS LDP Entity Configurable ATM Label Range Table. The purpose of this table is to provide a mechanism for specifying a contiguous range of vpi's with a contiguous range of vci's, or a 'label range' for LDP Entities. LDP Entities which use ATM must have at least one entry in this table." ::= { hwMplsLdpEntityObjects 3 } hwMplsLdpEntityConfAtmLabelRangeEntry OBJECT-TYPE SYNTAX HwMplsLdpEntityConfAtmLabelRangeEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A row in the LDP Entity Configurable ATM Label Range Table. One entry in this table contains information on a single range of labels represented by the configured Upper and Lower Bounds VPI/VCI pairs. NOTE: The ranges for a specific LDP Entity are UNIQUE and non-overlapping. For example, for a specific LDP Entity index, there could be one entry having ConfLowerBound vpi/vci == 0/32, and ConfUpperBound vpi/vci == 0/100, and a second entry for this same interface with ConfLowerBound vpi/vci == 0/101 and ConfUpperBound vpi/vci == 0/200. However, there could not be a third entry with ConfLowerBound vpi/vci == 0/200 and ConfUpperBound vpi/vci == 0/300 because this label range overlaps with the second entry (i.e. both entries now have 0/200). A row will not be created unless a unique and non-overlapping range is specified. Thus, row creation implies a one-shot row creation of LDP EntityID and ConfLowerBound vpi/vci and ConfUpperBound vpi/vci. At least one label range entry for a specific LDP Entity MUST include the default VPI/VCI values denoted in the LDP Entity Table." INDEX { hwMplsLdpLsrIncarnID, hwMplsLdpEntityIfIndex, hwMplsLdpEntityConfAtmLabelRangeLowerBoundVPI, hwMplsLdpEntityConfAtmLabelRangeLowerBoundVCI } ::= { hwMplsLdpEntityConfAtmLabelRangeTable 1 } HwMplsLdpEntityConfAtmLabelRangeEntry ::= SEQUENCE { hwMplsLdpEntityConfAtmLabelRangeLowerBoundVPI AtmVpIdentifier, hwMplsLdpEntityConfAtmLabelRangeLowerBoundVCI AtmVcIdentifier, hwMplsLdpEntityConfAtmLabelRangeUpperBoundVPI AtmVpIdentifier, hwMplsLdpEntityConfAtmLabelRangeUpperBoundVCI AtmVcIdentifier, hwMplsLdpEntityConfAtmLabelRangeRowStatus RowStatus } hwMplsLdpEntityConfAtmLabelRangeLowerBoundVPI OBJECT-TYPE SYNTAX AtmVpIdentifier MAX-ACCESS not-accessible STATUS current DESCRIPTION "The minimum VPI number configured for this range." ::= { hwMplsLdpEntityConfAtmLabelRangeEntry 1 } hwMplsLdpEntityConfAtmLabelRangeLowerBoundVCI OBJECT-TYPE SYNTAX AtmVcIdentifier MAX-ACCESS not-accessible STATUS current DESCRIPTION "The minimum VCI number configured for this range." ::= { hwMplsLdpEntityConfAtmLabelRangeEntry 2 } hwMplsLdpEntityConfAtmLabelRangeUpperBoundVPI OBJECT-TYPE SYNTAX AtmVpIdentifier MAX-ACCESS read-create STATUS current DESCRIPTION "The maximum VPI number configured for this range." ::= { hwMplsLdpEntityConfAtmLabelRangeEntry 3 } hwMplsLdpEntityConfAtmLabelRangeUpperBoundVCI OBJECT-TYPE SYNTAX AtmVcIdentifier MAX-ACCESS read-create STATUS current DESCRIPTION "The maximum VCI number configured for this range." ::= { hwMplsLdpEntityConfAtmLabelRangeEntry 4 } hwMplsLdpEntityConfAtmLabelRangeRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "An object that allows entries in this table to be created and deleted using the RowStatus convention." ::= { hwMplsLdpEntityConfAtmLabelRangeEntry 5 } -- -- The MPLS LDP Entity Statistics Table -- hwMplsLdpEntityStatsTable OBJECT-TYPE SYNTAX SEQUENCE OF HwMplsLdpEntityStatsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table is a read-only table which augments the MplsLdpConfEntityTable. The purpose of this table is to keep statistical information about the LDP Entities on the LSR." ::= { hwMplsLdpEntityObjects 4 } hwMplsLdpEntityStatsEntry OBJECT-TYPE SYNTAX HwMplsLdpEntityStatsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A row in this table contains statistical information about an LDP Entity." AUGMENTS { hwMplsLdpEntityEntry } ::= { hwMplsLdpEntityStatsTable 1 } HwMplsLdpEntityStatsEntry ::= SEQUENCE { hwMplsLdpAttemptedSessions Counter32 } hwMplsLdpAttemptedSessions OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "A count of the total attempted sessions for this LDP Entity." ::= { hwMplsLdpEntityStatsEntry 1 } -- -- The MPLS LDP Peer Table -- hwMplsLdpPeerTable OBJECT-TYPE SYNTAX SEQUENCE OF HwMplsLdpPeerEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Information about LDP peers which have been discovered by the LDP Entities that are managed by this agent." ::= { hwMplsLdpPeerObjects 1 } hwMplsLdpPeerEntry OBJECT-TYPE SYNTAX HwMplsLdpPeerEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Information about a single Peer." INDEX { hwMplsLdpLsrIncarnID, hwMplsLdpEntityIfIndex, hwMplsLdpPeerIndex } ::= { hwMplsLdpPeerTable 1 } HwMplsLdpPeerEntry ::= SEQUENCE { hwMplsLdpPeerIndex INTEGER, hwMplsLdpPeerID MplsLdpIdentifier, hwMplsLdpPeerInternetworkAddrType AddressFamilyNumbers, hwMplsLdpPeerInternetworkAddr MplsLdpGenAddr, hwMplsLdpPeerDefaultMtu INTEGER, hwMplsLdpPeerKeepAliveHoldTimer INTEGER, hwMplsLdpPeerLabelDistributionMethod INTEGER, hwMplsLdpPeerType INTEGER, hwMplsLdpPeerRowStatus RowStatus } hwMplsLdpPeerIndex OBJECT-TYPE SYNTAX INTEGER (1..4294967295) MAX-ACCESS not-accessible STATUS current DESCRIPTION "An identifier for the LDP peer that is unique within the scope of this agent." ::= { hwMplsLdpPeerEntry 1 } hwMplsLdpPeerID OBJECT-TYPE SYNTAX MplsLdpIdentifier MAX-ACCESS read-create STATUS current DESCRIPTION "The LDP identifier of this LDP Peer." ::= { hwMplsLdpPeerEntry 2 } hwMplsLdpPeerInternetworkAddrType OBJECT-TYPE SYNTAX AddressFamilyNumbers MAX-ACCESS read-create STATUS current DESCRIPTION "The type of the internetwork layer address of this LDP peer. This object indicates how the value of hwMplsLdpPeerInternetworkAddr is to be interpreted." ::= { hwMplsLdpPeerEntry 3 } hwMplsLdpPeerInternetworkAddr OBJECT-TYPE SYNTAX MplsLdpGenAddr MAX-ACCESS read-create STATUS current DESCRIPTION "The value of the internetwork layer address of this LDP peer." ::= { hwMplsLdpPeerEntry 4 } hwMplsLdpPeerDefaultMtu OBJECT-TYPE SYNTAX INTEGER (0..65535) MAX-ACCESS read-create STATUS current DESCRIPTION "The default maximum transmission unit (MTU) of the LDP Peer." DEFVAL { 9180 } ::= { hwMplsLdpPeerEntry 5 } hwMplsLdpPeerKeepAliveHoldTimer OBJECT-TYPE SYNTAX INTEGER (1..65535) UNITS "seconds" MAX-ACCESS read-create STATUS current DESCRIPTION "The two octet unsigned non zero INTEGER that indicates the number of seconds that this Peer proposes for the value of the KeepAlive Interval." ::= { hwMplsLdpPeerEntry 6 } hwMplsLdpPeerLabelDistributionMethod OBJECT-TYPE SYNTAX INTEGER { downstreamOnDemand(1), downstreamUnsolicited(2) } MAX-ACCESS read-create STATUS current DESCRIPTION "For any given LDP session, the method of label distribution must be specified." REFERENCE "draft-ietf-mpls-arch-05.txt [20]." ::= { hwMplsLdpPeerEntry 7 } hwMplsLdpPeerType OBJECT-TYPE SYNTAX INTEGER { local(1), remote(2) } MAX-ACCESS read-create STATUS current DESCRIPTION "Indicates whether a peer is a local peer or a remote peer" ::= { hwMplsLdpPeerEntry 8 } hwMplsLdpPeerRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "An object that allows entries in this table to be created and deleted using the RowStatus convention." ::= { hwMplsLdpPeerEntry 9 } -- -- The MPLS LDP Peer Configurable ATM Label Range Table -- hwMplsLdpPeerConfAtmLabelRangeTable OBJECT-TYPE SYNTAX SEQUENCE OF HwMplsLdpPeerConfAtmLabelRangeEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The MPLS LDP Peer Configurable ATM Label Range Table. The purpose of this table is to provide a mechanism for specifying a contiguous range of vpi's with a contiguous range of vci's, or a 'label range' for LDP Peers. LDP Peers which use ATM must have at least one entry in this table." ::= { hwMplsLdpPeerObjects 2 } hwMplsLdpPeerConfAtmLabelRangeEntry OBJECT-TYPE SYNTAX HwMplsLdpPeerConfAtmLabelRangeEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A row in the LDP Peer Configurable ATM Label Range Table. One entry in this table contains information on a single range of labels represented by the configured Upper and Lower Bounds VPI/VCI pairs. NOTE: The ranges for a specific LDP Peer are UNIQUE and non-overlapping. For example, for a specific LDP Peer index, there could be one entry having ConfLowerBound vpi/vci == 0/32, and ConfUpperBound vpi/vci == 0/100, and a second entry for this same interface with ConfLowerBound vpi/vci == 0/101 and ConfUpperBound vpi/vci == 0/200. However, there could not be a third entry with ConfLowerBound vpi/vci == 0/200 and ConfUpperBound vpi/vci == 0/300 because this label range overlaps with the second entry (i.e. both entries now have 0/200). A row will not be created unless a unique and non-overlapping range is specified. Thus, row creation implies a one-shot row creation of LDP PeerIndex and ConfLowerBound vpi/vci and ConfUpperBound vpi/vci. At least one label range entry for a specific LDP Peer MUST include the default VPI/VCI values denoted in the LDP Peer Table." INDEX { hwMplsLdpLsrIncarnID, hwMplsLdpEntityIfIndex, hwMplsLdpPeerIndex, hwMplsLdpPeerConfAtmLabelRangeLowerBoundVPI, hwMplsLdpPeerConfAtmLabelRangeLowerBoundVCI } ::= { hwMplsLdpPeerConfAtmLabelRangeTable 1 } HwMplsLdpPeerConfAtmLabelRangeEntry ::= SEQUENCE { hwMplsLdpPeerConfAtmLabelRangeLowerBoundVPI AtmVpIdentifier, hwMplsLdpPeerConfAtmLabelRangeLowerBoundVCI AtmVcIdentifier, hwMplsLdpPeerConfAtmLabelRangeUpperBoundVPI AtmVpIdentifier, hwMplsLdpPeerConfAtmLabelRangeUpperBoundVCI AtmVcIdentifier } hwMplsLdpPeerConfAtmLabelRangeLowerBoundVPI OBJECT-TYPE SYNTAX AtmVpIdentifier MAX-ACCESS not-accessible STATUS current DESCRIPTION "The minimum VPI number configured for this range." ::= { hwMplsLdpPeerConfAtmLabelRangeEntry 1 } hwMplsLdpPeerConfAtmLabelRangeLowerBoundVCI OBJECT-TYPE SYNTAX AtmVcIdentifier MAX-ACCESS not-accessible STATUS current DESCRIPTION "The minimum VCI number configured for this range." ::= { hwMplsLdpPeerConfAtmLabelRangeEntry 2 } hwMplsLdpPeerConfAtmLabelRangeUpperBoundVPI OBJECT-TYPE SYNTAX AtmVpIdentifier MAX-ACCESS read-only STATUS current DESCRIPTION "The maximum VPI number configured for this range." ::= { hwMplsLdpPeerConfAtmLabelRangeEntry 3 } hwMplsLdpPeerConfAtmLabelRangeUpperBoundVCI OBJECT-TYPE SYNTAX AtmVcIdentifier MAX-ACCESS read-only STATUS current DESCRIPTION "The maximum VCI number configured for this range." ::= { hwMplsLdpPeerConfAtmLabelRangeEntry 4 } -- -- The MPLS LDP Sessions Table -- hwMplsLdpSessionTable OBJECT-TYPE SYNTAX SEQUENCE OF HwMplsLdpSessionEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table of Sessions between the LDP Entities and LDP Peers." ::= { hwMplsLdpSessionObjects 1 } hwMplsLdpSessionEntry OBJECT-TYPE SYNTAX HwMplsLdpSessionEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in this table represents information on a single session between an LDP Entity and LDP Peer." INDEX { hwMplsLdpLsrIncarnID, hwMplsLdpEntityIfIndex, hwMplsLdpPeerIndex, hwMplsLdpSessionIndex } ::= { hwMplsLdpSessionTable 1 } HwMplsLdpSessionEntry ::= SEQUENCE { hwMplsLdpSessionIndex INTEGER, hwMplsLdpSessionID MplsLdpIdentifier, hwMplsLdpSessionProtocolVersion INTEGER, hwMplsLdpSessionKeepAliveHoldTimeRemaining TimeInterval, hwMplsLdpSessionRole INTEGER, hwMplsLdpSessionState INTEGER, hwMplsLdpSessionAtmLabelRangeLowerBoundVPI AtmVpIdentifier, hwMplsLdpSessionAtmLabelRangeLowerBoundVCI AtmVcIdentifier, hwMplsLdpSessionAtmLabelRangeUpperBoundVPI AtmVpIdentifier, hwMplsLdpSessionAtmLabelRangeUpperBoundVCI AtmVcIdentifier } hwMplsLdpSessionIndex OBJECT-TYPE SYNTAX INTEGER (1..4294967295) MAX-ACCESS not-accessible STATUS current DESCRIPTION "An unique identifier for this entry such that it identifies a specific LDP Session." ::= { hwMplsLdpSessionEntry 1 } hwMplsLdpSessionID OBJECT-TYPE SYNTAX MplsLdpIdentifier MAX-ACCESS read-only STATUS current DESCRIPTION "The LDP Session identifier." ::= { hwMplsLdpSessionEntry 2 } hwMplsLdpSessionProtocolVersion OBJECT-TYPE SYNTAX INTEGER(0..65535) MAX-ACCESS read-only STATUS current DESCRIPTION "The version of the LDP Protocol which this session is using." ::= { hwMplsLdpSessionEntry 3 } hwMplsLdpSessionKeepAliveHoldTimeRemaining OBJECT-TYPE SYNTAX TimeInterval MAX-ACCESS read-only STATUS current DESCRIPTION "The keep alive hold time remaining for this session." ::= { hwMplsLdpSessionEntry 4 } hwMplsLdpSessionRole OBJECT-TYPE SYNTAX INTEGER { active(1), passive(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "An indication of whether the LDP Entity associated with this session is acting in an 'active' role or a 'passive' role." ::= { hwMplsLdpSessionEntry 5 } hwMplsLdpSessionState OBJECT-TYPE SYNTAX INTEGER { nonexistent(1), initialized(2), openrec(3), opensent(4), operational(5) } MAX-ACCESS read-only STATUS current DESCRIPTION "The current state of the session, all of the states 1 - 5 are based on the state machine for session negotiation behavior." ::= { hwMplsLdpSessionEntry 6 } hwMplsLdpSessionAtmLabelRangeLowerBoundVPI OBJECT-TYPE SYNTAX AtmVpIdentifier MAX-ACCESS read-only STATUS current DESCRIPTION "The minimum VPI number for this range." ::= { hwMplsLdpSessionEntry 7 } hwMplsLdpSessionAtmLabelRangeLowerBoundVCI OBJECT-TYPE SYNTAX AtmVcIdentifier MAX-ACCESS read-only STATUS current DESCRIPTION "The minimum VCI number for this range." ::= { hwMplsLdpSessionEntry 8 } hwMplsLdpSessionAtmLabelRangeUpperBoundVPI OBJECT-TYPE SYNTAX AtmVpIdentifier MAX-ACCESS read-only STATUS current DESCRIPTION "The maximum VPI number for this range." ::= { hwMplsLdpSessionEntry 9 } hwMplsLdpSessionAtmLabelRangeUpperBoundVCI OBJECT-TYPE SYNTAX AtmVcIdentifier MAX-ACCESS read-only STATUS current DESCRIPTION "The maximum VCI number for this range." ::= { hwMplsLdpSessionEntry 10 } -- -- The MPLS LDP Hello Adjacency Table -- hwMplsLdpHelloAdjacencyTable OBJECT-TYPE SYNTAX SEQUENCE OF HwMplsLdpHelloAdjacencyEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table of Hello Adjacencies for Sessions." ::= { hwMplsLdpHelloAdjacencyObjects 1 } hwMplsLdpHelloAdjacencyEntry OBJECT-TYPE SYNTAX HwMplsLdpHelloAdjacencyEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Each row represents a single LDP Hello Adjacency. An LDP Session can have one or more Hello adjacencies." INDEX { hwMplsLdpLsrIncarnID, hwMplsLdpEntityIfIndex, hwMplsLdpPeerIndex, hwMplsLdpSessionIndex, hwMplsLdpHelloAdjacencyIndex } ::= { hwMplsLdpHelloAdjacencyTable 1 } HwMplsLdpHelloAdjacencyEntry ::= SEQUENCE { hwMplsLdpHelloAdjacencyIndex INTEGER, hwMplsLdpHelloAdjacencyHoldTimeRemaining TimeInterval } hwMplsLdpHelloAdjacencyIndex OBJECT-TYPE SYNTAX INTEGER (1..4294967295) MAX-ACCESS not-accessible STATUS current DESCRIPTION "An identifier for the adjacency." ::= { hwMplsLdpHelloAdjacencyEntry 1 } hwMplsLdpHelloAdjacencyHoldTimeRemaining OBJECT-TYPE SYNTAX TimeInterval MAX-ACCESS read-only STATUS current DESCRIPTION "The time remaining for this Hello Adjacency." ::= { hwMplsLdpHelloAdjacencyEntry 2 } -- -- FSMPLS- CRLSP Table -- hwMplsLdpCrlspTnlTable OBJECT-TYPE SYNTAX SEQUENCE OF HwMplsLdpCrlspTnlEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The hwMplsLdpCrlspTnlTable allows new CRLSP MPLS tunnels to be created. The ER hops associated with a CRLSP tunnel are to be configured using the hwMplsLdpCrlspErHopTable." ::= { hwMplsLdpCrlspTnlObjects 1 } hwMplsLdpCrlspTnlEntry OBJECT-TYPE SYNTAX HwMplsLdpCrlspTnlEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in this table represents an CRLSP MPLS tunnel. An entry can be created by a network administrator." INDEX { hwMplsLdpLsrIncarnID, hwMplsLdpCrlspTnlIndex } ::= { hwMplsLdpCrlspTnlTable 1 } HwMplsLdpCrlspTnlEntry ::= SEQUENCE { hwMplsLdpCrlspTnlIndex MplsTunnelIndex, hwMplsLdpCrlspTnlName DisplayString, hwMplsLdpCrlspTnlDirection INTEGER, hwMplsLdpCrlspTnlSignallingProto INTEGER, hwMplsLdpCrlspTnlSetupPrio INTEGER, hwMplsLdpCrlspTnlHoldingPrio INTEGER, hwMplsLdpCrlspTnlPeakDataRate BitRate, hwMplsLdpCrlspTnlPeakBurstSize BurstSize, hwMplsLdpCrlspTnlCommittedDataRate BitRate, hwMplsLdpCrlspTnlCommittedBurstSize BurstSize, hwMplsLdpCrlspTnlExcessBurstSize BurstSize, hwMplsLdpCrlspTnlIsPinned TruthValue, hwMplsLdpCrlspTnlFrequency INTEGER, hwMplsLdpCrlspTnlWeight INTEGER, hwMplsLdpCrlspTnlRowStatus RowStatus } hwMplsLdpCrlspTnlIndex OBJECT-TYPE SYNTAX MplsTunnelIndex MAX-ACCESS not-accessible STATUS current DESCRIPTION "Uniquely identifies this row." ::= { hwMplsLdpCrlspTnlEntry 1 } hwMplsLdpCrlspTnlName OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-create STATUS current DESCRIPTION "The 'canonical' name assigned to the tunnel that can be used to refer to it on the 'console' port." ::= { hwMplsLdpCrlspTnlEntry 2 } hwMplsLdpCrlspTnlDirection OBJECT-TYPE SYNTAX INTEGER { in(1), out(2), inOut(3) } MAX-ACCESS read-create STATUS current DESCRIPTION "Whether this tunnel is unidirectional-incoming, unidirectional-outgoing, or bidirectional." ::= { hwMplsLdpCrlspTnlEntry 3 } hwMplsLdpCrlspTnlSignallingProto OBJECT-TYPE SYNTAX INTEGER { none(1), ldp(2), rsvp(3) } MAX-ACCESS read-create STATUS current DESCRIPTION "The signaling protocol, if any, that set up this tunnel." DEFVAL { none } ::= { hwMplsLdpCrlspTnlEntry 4 } hwMplsLdpCrlspTnlSetupPrio OBJECT-TYPE SYNTAX INTEGER (0..7) MAX-ACCESS read-create STATUS current DESCRIPTION "The setup priority of this tunnel." REFERENCE "Extensions to RSVP for LSP Tunnels, Awduche et al, Internet Draft , March 1999., Constraint-Based LSP Setup using LDP, Jamoussi, Internet Draft , Feb. 1999." ::= { hwMplsLdpCrlspTnlEntry 5 } hwMplsLdpCrlspTnlHoldingPrio OBJECT-TYPE SYNTAX INTEGER (0..7) MAX-ACCESS read-create STATUS current DESCRIPTION "The holding priority for this tunnel." REFERENCE " Extensions to RSVP for LSP Tunnels, Awduche et al, Internet Draft , March 1999., Constraint-Based LSP Setup using LDP, Jamoussi, Internet Draft , Feb. 1999." ::= { hwMplsLdpCrlspTnlEntry 6 } hwMplsLdpCrlspTnlPeakDataRate OBJECT-TYPE SYNTAX BitRate UNITS "bits per second" MAX-ACCESS read-create STATUS current DESCRIPTION "The peak rate - the maximum rate at which traffic will be sent on the CRLSP." REFERENCE "Section 4.3.1.2, Constraint-Based LSP Setup using LDP, Jamoussi, et. al, , August 1999." DEFVAL { 0 } ::= { hwMplsLdpCrlspTnlEntry 7 } hwMplsLdpCrlspTnlPeakBurstSize OBJECT-TYPE SYNTAX BurstSize UNITS "bytes" MAX-ACCESS read-create STATUS current DESCRIPTION "The peak burst size - the maximum burst size of the traffic that can occur in the established CRLSP." REFERENCE "Section 4.3, Constraint-Based LSP Setup using LDP, Jamoussi, et. al, , August 1999." DEFVAL { 0 } ::= { hwMplsLdpCrlspTnlEntry 8 } hwMplsLdpCrlspTnlCommittedDataRate OBJECT-TYPE SYNTAX BitRate UNITS "bits per second" MAX-ACCESS read-create STATUS current DESCRIPTION "The committed rate - the committed rate at which traffic will be sent on the CRLSP." REFERENCE "Section 4.3.1.3, Constraint-Based LSP Setup using LDP, Jamoussi, et. al, , August 1999." DEFVAL { 0 } ::= { hwMplsLdpCrlspTnlEntry 9 } hwMplsLdpCrlspTnlCommittedBurstSize OBJECT-TYPE SYNTAX BurstSize UNITS "bytes" MAX-ACCESS read-create STATUS current DESCRIPTION "The committed burst size - the committed burst size of the traffic that will be handled in the established CRLSP." REFERENCE "Section 4.3, Constraint-Based LSP Setup using LDP, Jamoussi, et. al, , August 1999." DEFVAL { 0 } ::= { hwMplsLdpCrlspTnlEntry 10 } hwMplsLdpCrlspTnlExcessBurstSize OBJECT-TYPE SYNTAX BurstSize UNITS "bytes" MAX-ACCESS read-create STATUS current DESCRIPTION "The Excess burst size - the excess burst size limit to be used for traffic conditioning at the ingress of the CRLSP." REFERENCE "Section 4.3.1.4, Constraint-Based LSP Setup using LDP, Jamoussi, et. al, , August 1999." DEFVAL { 0 } ::= { hwMplsLdpCrlspTnlEntry 11 } hwMplsLdpCrlspTnlIsPinned OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-create STATUS current DESCRIPTION "Indicates whether the loose-routed hops of this tunnel are to be pinned." DEFVAL { false } ::= { hwMplsLdpCrlspTnlEntry 12 } hwMplsLdpCrlspTnlFrequency OBJECT-TYPE SYNTAX INTEGER (0..2) MAX-ACCESS read-create STATUS current DESCRIPTION "Indicates the frequency of usage of the established CRLSP." REFERENCE "Section 4.3.1.1, Constraint-Based LSP Setup using LDP, Jamoussi, et. al, , August 1999." ::= { hwMplsLdpCrlspTnlEntry 13 } hwMplsLdpCrlspTnlWeight OBJECT-TYPE SYNTAX INTEGER (0..255) MAX-ACCESS read-create STATUS current DESCRIPTION "Indicates the weight that is the established CRLSP." REFERENCE "Section 4.3, Constraint-Based LSP Setup using LDP, Jamoussi, et. al, , August 1999." ::= { hwMplsLdpCrlspTnlEntry 14 } hwMplsLdpCrlspTnlRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "For controlling the state of this row. The status can be set to 'active' only when atleast one ERHOP is created in the hwMplsLdpErHopTable, associated with this tunnel." ::= { hwMplsLdpCrlspTnlEntry 15 } -- -- Er-Hop Table -- hwMplsLdpCrlspErHopTable OBJECT-TYPE SYNTAX SEQUENCE OF HwMplsLdpCrlspErHopEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The hwMplsLdpCrlspErHopTable is used to indicate the hops, strict or loose, for an MPLS CRLSP tunnel defined in hwMplsLdpCrlspTnlTable. There must be atleast one entry in this table for each CRLSP tunnel that is supported in the hwMplsLdpCrlspTnlTable. The first row in the table is the first hop after the origination point of the tunnel." ::= { hwMplsLdpCrlspTnlObjects 2 } hwMplsLdpCrlspErHopEntry OBJECT-TYPE SYNTAX HwMplsLdpCrlspErHopEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in this table represents a tunnel hop. An entry is created by a network administrator for signalled ERLSP set up by LDP or RSVP." INDEX { hwMplsLdpLsrIncarnID, hwMplsLdpCrlspTnlIndex, hwMplsLdpCrlspErHopIndex } ::= { hwMplsLdpCrlspErHopTable 1 } HwMplsLdpCrlspErHopEntry ::= SEQUENCE { hwMplsLdpCrlspErHopIndex INTEGER, hwMplsLdpCrlspErHopAddrType INTEGER, hwMplsLdpCrlspErHopIpv4Addr IpAddress, hwMplsLdpCrlspErHopIpv4PrefixLen INTEGER, hwMplsLdpCrlspErHopStrictOrLoose INTEGER, hwMplsLdpCrlspErHopRowStatus RowStatus } hwMplsLdpCrlspErHopIndex OBJECT-TYPE SYNTAX INTEGER MAX-ACCESS not-accessible STATUS current DESCRIPTION "Secondary index into this table identifying the particular hop." ::= { hwMplsLdpCrlspErHopEntry 1 } hwMplsLdpCrlspErHopAddrType OBJECT-TYPE SYNTAX INTEGER { ipV4(1) } MAX-ACCESS read-create STATUS current DESCRIPTION "Address type of this hop." DEFVAL { ipV4 } ::= { hwMplsLdpCrlspErHopEntry 2 } hwMplsLdpCrlspErHopIpv4Addr OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-create STATUS current DESCRIPTION "If hwMplsLdpCrlspErHopAddrType is ipV4(1), IPv4 address of this hop. This object is not significant otherwise and should return a value of 0." ::= { hwMplsLdpCrlspErHopEntry 3 } hwMplsLdpCrlspErHopIpv4PrefixLen OBJECT-TYPE SYNTAX INTEGER (1..32) MAX-ACCESS read-create STATUS current DESCRIPTION "If hwMplsLdpCrlspErHopAddrType is ipV4(1), prefix length for this hop's IPv4 address. This object is not significant otherwise and should return a value of 0." ::= { hwMplsLdpCrlspErHopEntry 4 } hwMplsLdpCrlspErHopStrictOrLoose OBJECT-TYPE SYNTAX INTEGER { strict(1), loose(2) } MAX-ACCESS read-create STATUS current DESCRIPTION "Whether this is a strict or loose hop." ::= { hwMplsLdpCrlspErHopEntry 5 } hwMplsLdpCrlspErHopRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "For creating, modifying and deleting this row." ::= { hwMplsLdpCrlspErHopEntry 6 } --- --- Notifications --- hwMplsLdpNotificationPrefix OBJECT IDENTIFIER ::= { hwMplsLdpNotifications 0 } hwMplsLdpFailedInitSessionThresholdExceeded NOTIFICATION-TYPE OBJECTS { hwMplsLdpLsrIncarnID, hwMplsLdpEntityID, hwMplsLdpEntityFailedInitSessionThreshold } STATUS current DESCRIPTION "This notification is generated whenever the value of hwMplsLdpEntityFailedInitSessionThreshold is exceeded." ::= { hwMplsLdpNotificationPrefix 1 } -- OBJECTS { hwMplsLdpLsrIncarnID, hwMplsLdpEntityID, -- hwMplsLdpEntityFailedInitSessionThreshold -- } -- STATUS current -- DESCRIPTION -- "This notification is generated whenever the value -- of hwMplsLdpEntityFailedInitSessionThreshold is -- exceeded." -- ::= { hwMplsLdpNotificationPrefix 1 } hwMplsLdpCrlspTunnelUp NOTIFICATION-TYPE OBJECTS { hwMplsLdpLsrIncarnID, hwMplsLdpEntityID, hwMplsLdpCrlspTnlIndex } STATUS current DESCRIPTION "This notification is generated by the Ingress LSR of the CRLSP tunnel on the receipt of Label mapping message from the downstream LSR for the LAbel request sent for the CRLSP tunnel." ::= { hwMplsLdpNotificationPrefix 2 } hwMplsLdpCrlspTunnelDown NOTIFICATION-TYPE OBJECTS { hwMplsLdpLsrIncarnID, hwMplsLdpEntityID, hwMplsLdpCrlspTnlIndex } STATUS current DESCRIPTION "This notification is generated when a CRLSP Row status is modified to destroy the CRLSP tunnel. - due to pre-emption etc.," ::= { hwMplsLdpNotificationPrefix 3 } hwMplsLdpCrlspTunnelSetupFailure NOTIFICATION-TYPE OBJECTS { hwMplsLdpLsrIncarnID, hwMplsLdpEntityID, hwMplsLdpCrlspTnlIndex } STATUS current DESCRIPTION "This notification is generated by the Ingress LSR of the CRLSP tunnel on the receipt of Nak message from the downstream LSR for the Label request sent for the CRLSP tunnel. This can occur due to improper ER hop values being set, or Traffic resources not available etc.," ::= { hwMplsLdpNotificationPrefix 4 } hwMplsLdpIncarnUpEventFailure NOTIFICATION-TYPE OBJECTS { hwMplsLdpLsrIncarnID} STATUS current DESCRIPTION "This notification is generated by LDP to notify the Incarnation UP Event failure" ::= { hwMplsLdpNotificationPrefix 11 } hwMplsLdpIncarnDownEventFailure NOTIFICATION-TYPE OBJECTS {hwMplsLdpLsrIncarnID} STATUS current DESCRIPTION "This notification is generated by LDP to notify the Incarnation DOWN Event failure" ::= { hwMplsLdpNotificationPrefix 12 } hwMplsLdpEntityUpEventFailure NOTIFICATION-TYPE OBJECTS { hwMplsLdpLsrIncarnID, hwMplsLdpEntityID} STATUS current DESCRIPTION "This notification is generated by LDP to notify the ENTITY UP Event failure" ::= { hwMplsLdpNotificationPrefix 13 } hwMplsLdpEntityDownEventFailure NOTIFICATION-TYPE OBJECTS {hwMplsLdpLsrIncarnID, hwMplsLdpEntityID} STATUS current DESCRIPTION "This notification is generated by LDP to notify the ENTITY DOWN Event failure" ::={ hwMplsLdpNotificationPrefix 14 } hwMplsLdpSessionUpEventFailure NOTIFICATION-TYPE OBJECTS {hwMplsLdpSessionID, hwMplsLdpSessionState} STATUS current DESCRIPTION "Generation of this trap occurs when the value of 'hwMplsLdpSessionState' enters the 'operational(5)' state." ::={ hwMplsLdpNotificationPrefix 15 } hwMplsLdpSessionDownEventFailure NOTIFICATION-TYPE OBJECTS {hwMplsLdpSessionID, hwMplsLdpSessionState} STATUS current DESCRIPTION "Generation of this trap occurs when the value of 'hwMplsLdpSessionState' leaves the 'operational(5)' state." ::={ hwMplsLdpNotificationPrefix 16 } -- End of notifications. END