--******************************************************************* -- FC-SP Policy -- T11-FC-SP-POLICY-MIB DEFINITIONS ::= BEGIN IMPORTS MODULE-IDENTITY, OBJECT-TYPE, NOTIFICATION-TYPE, mib-2, Counter32, Unsigned32 FROM SNMPv2-SMI -- [RFC2578] RowStatus, StorageType, TimeStamp, TruthValue FROM SNMPv2-TC -- [RFC2579] MODULE-COMPLIANCE, OBJECT-GROUP, NOTIFICATION-GROUP FROM SNMPv2-CONF -- [RFC2580] SnmpAdminString FROM SNMP-FRAMEWORK-MIB -- [RFC3411] InetAddress, InetPortNumber, InetAddressType FROM INET-ADDRESS-MIB -- [RFC4001] fcmInstanceIndex, FcNameIdOrZero, FcDomainIdOrZero FROM FC-MGMT-MIB -- [RFC4044] T11NsGs4RejectReasonCode FROM T11-FC-NAME-SERVER-MIB -- [RFC4438] T11FabricIndex FROM T11-TC-MIB -- [RFC4439] T11FcSpAlphaNumName, T11FcSpAlphaNumNameOrAbsent, T11FcSpPolicyName, T11FcSpPolicyNameType, T11FcSpPolicyObjectType, T11FcSpPolicyHashFormat, T11FcSpPolicyHashValue, T11FcSpHashCalculationStatus FROM T11-FC-SP-TC-MIB; t11FcSpPolicyMIB MODULE-IDENTITY LAST-UPDATED "200808200000Z" ORGANIZATION "This MIB module was developed through the coordinated effort of two organizations: T11 began the development and the IETF (in the IMSS Working Group) finished it." CONTACT-INFO " Claudio DeSanti Cisco Systems, Inc. 170 West Tasman Drive San Jose, CA 95134 USA EMail: cds@cisco.com Keith McCloghrie Cisco Systems, Inc. 170 West Tasman Drive San Jose, CA 95134 USA Email: kzm@cisco.com" DESCRIPTION "This MIB module specifies the management information required to manage Fabric Policies as defined by Fibre Channel's FC-SP specification. FC-SP uses the term 'Policy Objects', sometimes abbreviated to just 'Objects', to refer to containers used to hold the data by which Fabric Policies are specified/stored. This obviously has the potential to cause confusion between 'Policy Objects' and 'MIB objects'. The DESCRIPTIONs in this MIB module attempt to avoid such confusion by the use of different adjectives and capitalization, even though such mechanisms are less effective when used in descriptors. Some types of Policy Objects contain multiple items of information, each of which are held in the same format within the Policy Object. In such cases, FC-SP uses the term 'Entry' to describe each instance of the common format. For example, FC-SP defines an Attribute Policy Object as containing one or more 'Attribute Entries'. Again, this MIB module attempts to avoid confusion by the use of adjectives and capitalization to distinguish an Entry within a Policy Object from an entry within a MIB table. A Fabric's database of Policy Objects consists of a set of active Objects that are to be enforced by that Fabric, as well as non-active Objects that are not enforced. Operations defined (in FC-SP) for Policy Management are: - Add/Get/Remove operations on individual non-active Policy Objects, - Activate/Deactivate operations on a Policy Summary Object, and - Get operations on the active Policy Summary Object and/or on individual active Policy Objects. This MIB module has five parts: 1) Active Policy Objects - read-only MIB objects representing the set of active Policy Objects for each Fabric, 2) Activate/Deactivate Operations - a read-write MIB object to invoke an Activate operation of the policies specified via a non-active Policy Summary Object, and - a read-write MIB object to invoke a Deactivate operation. 3) Non-active Policy Objects - read-create MIB objects to allow the creation of non-active Policy Summary Objects (which reference non-active Policy Objects), and - read-create MIB objects representing non-active Policy Objects. 4) Statistics 5) Control information and Notifications Copyright (C) The IETF Trust (2008). This version of this MIB module is part of RFC 5324; see the RFC itself for full legal notices." REVISION "200808200000Z" DESCRIPTION "Initial version of this MIB module, published as RFC 5324." ::= { mib-2 178 } t11FcSpPoMIBNotifications OBJECT IDENTIFIER ::= { t11FcSpPolicyMIB 0 } t11FcSpPoMIBObjects OBJECT IDENTIFIER ::= { t11FcSpPolicyMIB 1 } t11FcSpPoMIBConformance OBJECT IDENTIFIER ::= { t11FcSpPolicyMIB 2 } t11FcSpPoActive OBJECT IDENTIFIER ::= { t11FcSpPoMIBObjects 1 } t11FcSpPoOperations OBJECT IDENTIFIER ::= { t11FcSpPoMIBObjects 2 } t11FcSpPoNonActive OBJECT IDENTIFIER ::= { t11FcSpPoMIBObjects 3 } t11FcSpPoStatistics OBJECT IDENTIFIER ::= { t11FcSpPoMIBObjects 4 } t11FcSpPoControl OBJECT IDENTIFIER ::= { t11FcSpPoMIBObjects 5 } -- -- Part 1 - Active Policy Objects -- t11FcSpPoTable OBJECT-TYPE SYNTAX SEQUENCE OF T11FcSpPoEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table containing top-level information about active FC-SP policies on various Fabrics." ::= { t11FcSpPoActive 1 } t11FcSpPoEntry OBJECT-TYPE SYNTAX T11FcSpPoEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Each entry contains information about active FC-SP policies for a particular Fabric, managed as part of the Fibre Channel management instance identified by fcmInstanceIndex." INDEX { fcmInstanceIndex, t11FcSpPoFabricIndex } ::= { t11FcSpPoTable 1 } T11FcSpPoEntry ::= SEQUENCE { t11FcSpPoFabricIndex T11FabricIndex, t11FcSpPoPolicySummaryObjName T11FcSpAlphaNumName, t11FcSpPoAdminFabricName FcNameIdOrZero, t11FcSpPoActivatedTimeStamp TimeStamp } t11FcSpPoFabricIndex OBJECT-TYPE SYNTAX T11FabricIndex MAX-ACCESS not-accessible STATUS current DESCRIPTION "An index value that uniquely identifies a particular Fabric." ::= { t11FcSpPoEntry 1 } t11FcSpPoPolicySummaryObjName OBJECT-TYPE SYNTAX T11FcSpAlphaNumName MAX-ACCESS read-only STATUS current DESCRIPTION "The name of this Fabric's (active) Policy Summary Object." REFERENCE "- ANSI INCITS 426-2007, T11/Project 1570-D, Fibre Channel - Security Protocols (FC-SP), February 2007, section 7.1.3 and table 104." ::= { t11FcSpPoEntry 2 } t11FcSpPoAdminFabricName OBJECT-TYPE SYNTAX FcNameIdOrZero (SIZE (8)) MAX-ACCESS read-only STATUS current DESCRIPTION "The administratively-specified name for this Fabric, as specified in the active Switch Membership List Object. This value is meaningful only when Static Domain_IDs are in use in a Fabric (see FC-SW-4). Static Domain_IDs are administratively enabled by a setting of the Switch Flags in each Switch Entry in the Switch Membership List Object. If Static Domain_IDs are not in use, this value might be '0000000000000000'h. The t11FamEnable, t11FamFabricName, and t11FamConfigDomainIdType objects defined in the T11-FC-FABRIC-ADDR-MGR-MIB module are also concerned with the use of an administratively-specified name for a Fabric and Static Domain_IDs. When FC-SP Policy is in use in a Fabric, the values of t11FamEnable, t11FamFabricName, and t11FamConfigDomainIdType must be read-only and reflect the active Policy Objects. For example, the value of t11FamFabricName must reflect the value of t11FcSpPoAdminFabricName." REFERENCE "- ANSI INCITS 426-2007, T11/Project 1570-D, Fibre Channel - Security Protocols (FC-SP), February 2007, section 7.1.4.1 and table 108. - Fibre Channel - Switch Fabric-4 (FC-SW-4), ANSI INCITS 418-2006, April 2006, section 7.1. - Fibre Channel Fabric Address Manager MIB', RFC 4439, March 2006." ::= { t11FcSpPoEntry 3 } t11FcSpPoActivatedTimeStamp OBJECT-TYPE SYNTAX TimeStamp MAX-ACCESS read-only STATUS current DESCRIPTION "The value of sysUpTime at which this Fabric's Policy Summary Object was last activated, or zero if the same Policy Summary Object has been active since the last restart of the management system." ::= { t11FcSpPoEntry 4 } -- -- The table of Policy Summary Objects -- t11FcSpPoSummaryTable OBJECT-TYPE SYNTAX SEQUENCE OF T11FcSpPoSummaryEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table of information about active Policy Objects listed within FC-SP Policy Summary Objects." ::= { t11FcSpPoActive 2 } t11FcSpPoSummaryEntry OBJECT-TYPE SYNTAX T11FcSpPoSummaryEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Each entry contains information about one of the active Policy Objects listed within the Policy Summary Object for the Fabric identified by t11FcSpPoFabricIndex and managed within the Fibre Channel management instance identified by fcmInstanceIndex. How many Policy Objects of a given type can be active at any one time for a given Fabric depends on the type, as specified in FC-SP. For some types, it is one per Fabric; for other types, more than one can be active per Fabric. In both of these cases, the absence of any entries in this table for a particular type is equivalent to there being one Policy Object of that type that is empty, e.g., a Switch Membership List Object that identifies zero Switches." REFERENCE "- ANSI INCITS 426-2007, T11/Project 1570-D, Fibre Channel - Security Protocols (FC-SP), February 2007, section 7.1.3 and table 104." INDEX { fcmInstanceIndex, t11FcSpPoFabricIndex, t11FcSpPoSummaryPolicyNameType, t11FcSpPoSummaryPolicyName } ::= { t11FcSpPoSummaryTable 1 } T11FcSpPoSummaryEntry ::= SEQUENCE { t11FcSpPoSummaryPolicyNameType T11FcSpPolicyNameType, t11FcSpPoSummaryPolicyName T11FcSpPolicyName, t11FcSpPoSummaryPolicyType T11FcSpPolicyObjectType, t11FcSpPoSummaryHashFormat T11FcSpPolicyHashFormat, t11FcSpPoSummaryHashValue T11FcSpPolicyHashValue } t11FcSpPoSummaryPolicyNameType OBJECT-TYPE SYNTAX T11FcSpPolicyNameType { nodeName(1), alphaNumericName(7) } MAX-ACCESS not-accessible STATUS current DESCRIPTION "The combination of t11FcSpPoSummaryPolicyNameType and t11FcSpPoSummaryPolicyName specify the name of the Policy Object contained in the Policy Summary Object. The type of name is 'nodeName' if the value of the corresponding instance of t11FcSpPoSummaryPolicyType is 'switchConnectivity', or 'alphaNumericName' otherwise." ::= { t11FcSpPoSummaryEntry 1 } t11FcSpPoSummaryPolicyName OBJECT-TYPE SYNTAX T11FcSpPolicyName MAX-ACCESS not-accessible STATUS current DESCRIPTION "The combination of t11FcSpPoSummaryPolicyNameType and t11FcSpPoSummaryPolicyName specify the name of the Policy Object contained in the Policy Summary Object." ::= { t11FcSpPoSummaryEntry 2 } t11FcSpPoSummaryPolicyType OBJECT-TYPE SYNTAX T11FcSpPolicyObjectType MAX-ACCESS read-only STATUS current DESCRIPTION "The 'Identifier' that specifies the type of this Policy Object." REFERENCE "- ANSI INCITS 426-2007, T11/Project 1570-D, Fibre Channel - Security Protocols (FC-SP), February 2007, section 7.1.3.1 and table 104." ::= { t11FcSpPoSummaryEntry 3 } t11FcSpPoSummaryHashFormat OBJECT-TYPE SYNTAX T11FcSpPolicyHashFormat MAX-ACCESS read-only STATUS current DESCRIPTION "The format of this Policy Object's hash value as contained in the corresponding instance of the t11FcSpPoSummaryHashValue object." ::= { t11FcSpPoSummaryEntry 4 } t11FcSpPoSummaryHashValue OBJECT-TYPE SYNTAX T11FcSpPolicyHashValue MAX-ACCESS read-only STATUS current DESCRIPTION "The hash value of this Policy Object, in the format identified by the corresponding instance of the t11FcSpPoSummaryHashFormat object." ::= { t11FcSpPoSummaryEntry 5 } -- -- Switch Entries in Active Switch Membership List Objects -- t11FcSpPoSwMembTable OBJECT-TYPE SYNTAX SEQUENCE OF T11FcSpPoSwMembEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table of Switch Entries in active Switch Membership List Objects. One Switch Membership List Object is represented by all of the rows of this table that have the same values of fcmInstanceIndex and t11FcSpPoFabricIndex." REFERENCE "- ANSI INCITS 426-2007, T11/Project 1570-D, Fibre Channel - Security Protocols (FC-SP), February 2007, section 7.1.4.1 and table 110." ::= { t11FcSpPoActive 3 } t11FcSpPoSwMembEntry OBJECT-TYPE SYNTAX T11FcSpPoSwMembEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Each entry contains information about one Switch Entry within the active Switch Membership List Object for the Fabric identified by t11FcSpPoFabricIndex and managed within the Fibre Channel management instance identified by fcmInstanceIndex." INDEX { fcmInstanceIndex, t11FcSpPoFabricIndex, t11FcSpPoSwMembSwitchNameType, t11FcSpPoSwMembSwitchName } ::= { t11FcSpPoSwMembTable 1 } T11FcSpPoSwMembEntry ::= SEQUENCE { t11FcSpPoSwMembSwitchNameType T11FcSpPolicyNameType, t11FcSpPoSwMembSwitchName FcNameIdOrZero, t11FcSpPoSwMembSwitchFlags BITS, t11FcSpPoSwMembDomainID FcDomainIdOrZero, t11FcSpPoSwMembPolicyDataRole INTEGER, t11FcSpPoSwMembAuthBehaviour BITS, t11FcSpPoSwMembAttribute T11FcSpAlphaNumNameOrAbsent } t11FcSpPoSwMembSwitchNameType OBJECT-TYPE SYNTAX T11FcSpPolicyNameType { nodeName(1), restrictedNodeName(2), wildcard(5), restrictedWildcard(6) } MAX-ACCESS not-accessible STATUS current DESCRIPTION "If the value of this object is 'nodeName' or 'restrictedNodeName', then the combination of this object and t11FcSpPoSwMembSwitchName specify the Switch Name of this Switch Entry. The membership is restricted or unrestricted based on the name type. Restricted membership means that the Switch is not allowed to be part of the Fabric unless allowed by a specific Switch Connectivity Object. Unrestricted membership means that the Switch is allowed to be part of the Fabric unless disallowed by a specific Switch Connectivity Object. The values of 'wildcard' and 'restrictedWildcard' provide the means to specify whether to allow/deny membership for Switches not explicitly named in the Switch Membership List Object." REFERENCE "- ANSI INCITS 426-2007, T11/Project 1570-D, Fibre Channel - Security Protocols (FC-SP), February 2007, section 7.1.4.1 and table 110." ::= { t11FcSpPoSwMembEntry 1 } t11FcSpPoSwMembSwitchName OBJECT-TYPE SYNTAX FcNameIdOrZero (SIZE (8)) MAX-ACCESS not-accessible STATUS current DESCRIPTION "When the value of t11FcSpPoSwMembSwitchNameType is 'wildcard' or 'restrictedWildcard', this object has the value '0000000000000000'h. Otherwise, the combination of t11FcSpPoSwMembSwitchNameType and this object specify the Switch Name of this Switch Entry." REFERENCE "- ANSI INCITS 426-2007, T11/Project 1570-D, Fibre Channel - Security Protocols (FC-SP), February 2007, section 7.1.4.1 and table 110." ::= { t11FcSpPoSwMembEntry 2 } t11FcSpPoSwMembSwitchFlags OBJECT-TYPE SYNTAX BITS { staticDomainID(0), insistentDomainID(1), serialPortsAccess(2), physicalPortsAccess(3), managerRole(4) } MAX-ACCESS read-only STATUS current DESCRIPTION "Configurable options in respect to the administration of Policy Objects at this Switch: 'staticDomainID' - if this bit is set, the Switch uses the 'Static Domain_IDs behavior' (as defined in FC-SW-4). This bit needs to have the same setting for all Switches in a Fabric's Switch Membership List Object, or else the Fabric will partition. If this bit is set, the Domain_ID for the Switch is given by the corresponding instance of t11FcSpPoSwMembDomainID. 'insistentDomainID' - if this bit is set, the Switch uses the 'Insistent Domain_ID behavior' (see t11FamConfigDomainId of T11-FC-FABRIC-ADDR-MGR-MIB), the Domain_ID for the Switch is given by the corresponding instance of t11FcSpPoSwMembDomainID. 'serialPortsAccess' - the Switch allows management through serial ports when and only when this bit is set. 'physicalPortsAccess' - the Switch allows management through the physical panel when and only when this bit is set. 'managerRole' - the Switch is allowed to change the Fabric Policy configuration (on receipt of any of the EACA, Enhanced Stage Fabric Configuration (ESFC), Enhanced Update Fabric Configuration (EUFC), ACA, SFC, or UFC SW_ILSs) if and only if this bit is set. Whenever a Fabric has Active Policy Objects, the value of the t11FamConfigDomainIdType object defined in the T11-FC-FABRIC-ADDR-MGR-MIB module must be read-only and reflect the values of the 'staticDomainID' and 'insistentDomainID' bits of this object." REFERENCE "- ANSI INCITS 426-2007, T11/Project 1570-D, Fibre Channel - Security Protocols (FC-SP), February 2007, section 7.1.4.1 and table 112. - Fibre Channel - Switch Fabric-4 (FC-SW-4), ANSI INCITS 418-2006, April 2006, section 7.1. - t11FamConfigDomainIdType, T11-FC-FABRIC-ADDR-MGR-MIB, Fibre Channel Fabric Address Manager MIB, RFC 4439." ::= { t11FcSpPoSwMembEntry 3 } t11FcSpPoSwMembDomainID OBJECT-TYPE SYNTAX FcDomainIdOrZero MAX-ACCESS read-only STATUS current DESCRIPTION "The specified Domain_ID value when either of the 'staticDomainID' or 'insistentDomainID' bits are set in the corresponding instance of t11FcSpPoSwMembSwitchFlags. Whenever a Fabric has Active Policy Objects, the value of the t11FamConfigDomainId object defined in the T11-FC-FABRIC-ADDR-MGR-MIB module must be read-only and reflect the value of this object." REFERENCE "- ANSI INCITS 426-2007, T11/Project 1570-D, Fibre Channel - Security Protocols (FC-SP), February 2007, section 7.1.4.1 and tables 111 and 112. - t11FamConfigDomainId, T11-FC-FABRIC-ADDR-MGR-MIB, Fibre Channel Fabric Address Manager MIB, RFC 4439." ::= { t11FcSpPoSwMembEntry 4 } t11FcSpPoSwMembPolicyDataRole OBJECT-TYPE SYNTAX INTEGER { client(1), autonomous(2), server(3) } MAX-ACCESS read-only STATUS current DESCRIPTION "The role of the Switch in terms of which Policy data it retains/maintains: 'client' - the Switch operates as a Client Switch. A Client Switch maintains its own Switch Connectivity Object and all Fabric-wide List Objects. If FC-SP Zoning is used, a Client Switch maintains only the subset of the Active Zone Set that it requires to enforce the current Fabric Zoning configuration. 'autonomous' - the Switch operates as an Autonomous Switch. An Autonomous Switch maintains its own Switch Connectivity Object and all Fabric-wide List Objects. This is the same as 'client' except that if FC-SP Zoning is used, an Autonomous Switch maintains a complete copy of the Fabric Zoning Database. 'server' - the Switch operates as a Server Switch. A Server Switch maintains all Fabric-wide List Objects and the Switch Connectivity Objects of each Switch in the Fabric. If FC-SP Zoning is used, a Server Switch maintains a complete copy of the Fabric Zoning Database." REFERENCE "- ANSI INCITS 426-2007, T11/Project 1570-D, Fibre Channel - Security Protocols (FC-SP), February 2007, section 7.1.4.1 and table 113." ::= { t11FcSpPoSwMembEntry 5 } t11FcSpPoSwMembAuthBehaviour OBJECT-TYPE SYNTAX BITS { mustAuthenticate(0), rejectIsFailure(1) } MAX-ACCESS read-only STATUS current DESCRIPTION "The authentication behaviour of the Switch: 'mustAuthenticate' - if this bit is set, all connections between this Switch and neighbor Switches must be authenticated. 'rejectIsFailure' - if this bit is set, the rejection of an AUTH_Negotiate message must be considered as an authentication failure by this Switch." REFERENCE "- ANSI INCITS 426-2007, T11/Project 1570-D, Fibre Channel - Security Protocols (FC-SP), February 2007, section 7.1.4.1 and table 114." ::= { t11FcSpPoSwMembEntry 6 } t11FcSpPoSwMembAttribute OBJECT-TYPE SYNTAX T11FcSpAlphaNumNameOrAbsent MAX-ACCESS read-only STATUS current DESCRIPTION "The name of an active Attribute Policy Object that is defined for this Switch, or the zero-length string. The zero-length string indicates that no Attribute Policy Object is defined for this Switch." REFERENCE "- ANSI INCITS 426-2007, T11/Project 1570-D, Fibre Channel - Security Protocols (FC-SP), February 2007, section 7.1.4.1 and table 110." ::= { t11FcSpPoSwMembEntry 7 } -- -- Node Entries in Active Node Membership List Objects -- t11FcSpPoNoMembTable OBJECT-TYPE SYNTAX SEQUENCE OF T11FcSpPoNoMembEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table of Node Entries in active Node Membership List Objects. One Node Membership List Object is represented by all of the rows of this table that have the same values of fcmInstanceIndex and t11FcSpPoFabricIndex." ::= { t11FcSpPoActive 4 } t11FcSpPoNoMembEntry OBJECT-TYPE SYNTAX T11FcSpPoNoMembEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Each entry contains information about one Node Entry within the active Node Membership List Object for the Fabric identified by t11FcSpPoFabricIndex and managed within the Fibre Channel management instance identified by fcmInstanceIndex." INDEX { fcmInstanceIndex, t11FcSpPoFabricIndex, t11FcSpPoNoMembNodeNameType, t11FcSpPoNoMembNodeName } ::= { t11FcSpPoNoMembTable 1 } T11FcSpPoNoMembEntry ::= SEQUENCE { t11FcSpPoNoMembNodeNameType T11FcSpPolicyNameType, t11FcSpPoNoMembNodeName FcNameIdOrZero, t11FcSpPoNoMembFlags BITS, t11FcSpPoNoMembCtAccessIndex Unsigned32, t11FcSpPoNoMembAttribute T11FcSpAlphaNumNameOrAbsent } t11FcSpPoNoMembNodeNameType OBJECT-TYPE SYNTAX T11FcSpPolicyNameType { nodeName(1), restrictedNodeName(2), portName(3), restrictedPortName(4), wildcard(5), restrictedWildcard(6) } MAX-ACCESS not-accessible STATUS current DESCRIPTION "If the value of this object is 'wildcard' or 'restrictedWildcard', this Node Entry applies to Nodes not explicitly named in the Node Membership List Object. Otherwise, the combination of this object and t11FcSpPoNoMembNodeName specify the name of this Node Entry in the active Node Membership List Object. A Node is identified by its Node Name or by one or more of its Port Names. Restricted membership means that a Node is not allowed to be connected to the Fabric unless allowed by a specific Switch Connectivity Object. Unrestricted membership means that a Node is allowed to be connected to the Fabric unless disallowed by a specific Switch Connectivity Object." REFERENCE "- ANSI INCITS 426-2007, T11/Project 1570-D, Fibre Channel - Security Protocols (FC-SP), February 2007, section 7.1.4.1 and table 116." ::= { t11FcSpPoNoMembEntry 1 } t11FcSpPoNoMembNodeName OBJECT-TYPE SYNTAX FcNameIdOrZero (SIZE (8)) MAX-ACCESS not-accessible STATUS current DESCRIPTION "If the value of t11FcSpPoNoMembNodeNameType is 'wildcard' or 'restrictedWildcard', this object has the value '0000000000000000'h. Otherwise, the combination of t11FcSpPoNoMembNodeNameType and this object specify the name of this Node Entry is the active Node Membership List Object." REFERENCE "- ANSI INCITS 426-2007, T11/Project 1570-D, Fibre Channel - Security Protocols (FC-SP), February 2007, section 7.1.4.1 and table 116." ::= { t11FcSpPoNoMembEntry 2 } t11FcSpPoNoMembFlags OBJECT-TYPE SYNTAX BITS { scsiEnclosureAccess(0), authenticationRequired(1) } MAX-ACCESS read-only STATUS current DESCRIPTION "Configurable options in respect to the administration of Policy Objects at this Node: 'scsiEnclosureAccess' - the Node is allowed to control any Switch through SCSI Enclosure Services if this bit is set. If a Switch does not support SCSI Enclosure Services, this bit is ignored. 'authenticationRequired' - the Node is required to authenticate itself to any Switch to which it is connected if and only if this bit is set." REFERENCE "- ANSI INCITS 426-2007, T11/Project 1570-D, Fibre Channel - Security Protocols (FC-SP), February 2007, section 7.1.4.1 and table 118." ::= { t11FcSpPoNoMembEntry 3 } t11FcSpPoNoMembCtAccessIndex OBJECT-TYPE SYNTAX Unsigned32 (0..4294967295) MAX-ACCESS read-only STATUS current DESCRIPTION "If the value of this object is zero, then access by this Node to Generic Services is not limited by a Common Transport Access Specifier. Otherwise, the limits are specified by the set of Common Transport Access Descriptors contained in those rows of the t11FcSpPoCtDescrTable for the same Fabric and for which the value of t11FcSpPoCtDescrSpecifierIndex is the same as the value of this object." REFERENCE "- ANSI INCITS 426-2007, T11/Project 1570-D, Fibre Channel - Security Protocols (FC-SP), February 2007, section 7.1.4.1 and tables 118/119/120/121." ::= { t11FcSpPoNoMembEntry 4 } t11FcSpPoNoMembAttribute OBJECT-TYPE SYNTAX T11FcSpAlphaNumNameOrAbsent MAX-ACCESS read-only STATUS current DESCRIPTION "The name of an active Attribute Policy Object that is defined for this Node, or the zero-length string. The zero-length string indicates that no Attribute Policy Object is defined for this Node." REFERENCE "- ANSI INCITS 426-2007, T11/Project 1570-D, Fibre Channel - Security Protocols (FC-SP), February 2007, section 7.1.4.1 and table 116." ::= { t11FcSpPoNoMembEntry 5 } -- -- -- Common Transport Access Descriptors -- t11FcSpPoCtDescrTable OBJECT-TYPE SYNTAX SEQUENCE OF T11FcSpPoCtDescrEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table of Common Transport Access Descriptors being used within active Policy Objects. A Common Transport Access Specifier is a list of Common Transport Access Descriptors that specify whether a Node is allowed to access a Generic Service or Sub-Server. An active Common Transport Access Specifier is represented by all rows of this table that have the same values of fcmInstanceIndex, t11FcSpPoFabricIndex, and t11FcSpPoCtDescrSpecifierIndex." ::= { t11FcSpPoActive 5 } t11FcSpPoCtDescrEntry OBJECT-TYPE SYNTAX T11FcSpPoCtDescrEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Each entry contains information about one Common Transport Access Descriptor of an active Common Transport Access Specifier used within the Fabric identified by t11FcSpPoFabricIndex and managed within the Fibre Channel management instance identified by fcmInstanceIndex." INDEX { fcmInstanceIndex, t11FcSpPoFabricIndex, t11FcSpPoCtDescrSpecifierIndex, t11FcSpPoCtDescrIndex } ::= { t11FcSpPoCtDescrTable 1 } T11FcSpPoCtDescrEntry ::= SEQUENCE { t11FcSpPoCtDescrSpecifierIndex Unsigned32, t11FcSpPoCtDescrIndex Unsigned32, t11FcSpPoCtDescrFlags BITS, t11FcSpPoCtDescrGsType OCTET STRING, t11FcSpPoCtDescrGsSubType OCTET STRING } t11FcSpPoCtDescrSpecifierIndex OBJECT-TYPE SYNTAX Unsigned32 (1..4294967295) MAX-ACCESS not-accessible STATUS current DESCRIPTION "An index value that uniquely identifies a particular Common Transport Access Specifier within a Fabric." ::= { t11FcSpPoCtDescrEntry 1 } t11FcSpPoCtDescrIndex OBJECT-TYPE SYNTAX Unsigned32 (1..4294967295) MAX-ACCESS not-accessible STATUS current DESCRIPTION "An index value that uniquely identifies a particular Common Transport Access Descriptor within a Common Transport Access Specifier." ::= { t11FcSpPoCtDescrEntry 2 } t11FcSpPoCtDescrFlags OBJECT-TYPE SYNTAX BITS { allow(0), gsTypeWildcard(1), gsSubTypeWildcard(2), readOnly(3) } MAX-ACCESS read-only STATUS current DESCRIPTION "The flag bits that specify how access is to be limited by this Common Transport Access Descriptor: - allow -- access to the specified Generic Service and Server is allowed if this bit is set, and is to be denied if this bit is not set. - gsTypeWildcard -- if this bit is set, the Generic Service to be allowed/denied is specified by the value of t11FcSpPoCtDescrGsType. If this bit is set, then the gsSubTypeWildcard bit must not be set. - gsSubTypeWildcard -- if this bit is set, the Generic Service to be allowed/denied is specified by the value of t11FcSpPoCtDescrGsSubType. If this bit is set, then the gsTypeWildcard bit must not be set. - readOnly -- if this bit is set, then access is to be granted only for reading." ::= { t11FcSpPoCtDescrEntry 3 } t11FcSpPoCtDescrGsType OBJECT-TYPE SYNTAX OCTET STRING (SIZE (1)) MAX-ACCESS read-only STATUS current DESCRIPTION "The GS_Type of the Generic Service (e.g., the FC-GS-5 Management Service) that is subject to access control. This value is ignored if the gsTypeWildcard bit is not set in the corresponding value of t11FcSpPoCtDescrFlags." REFERENCE "- Fibre Channel - Generic Services-5 (FC-GS-5), ANSI INCITS 427-2006, section 4.3.2.4." ::= { t11FcSpPoCtDescrEntry 4 } t11FcSpPoCtDescrGsSubType OBJECT-TYPE SYNTAX OCTET STRING (SIZE (1)) MAX-ACCESS read-only STATUS current DESCRIPTION "The GS_Subtype of the Generic Server (e.g., the Fabric Zone Server) that is subject to access control. This value is ignored if the gsSubTypeWildcard bit is not set in the corresponding value of t11FcSpPoCtDescrFlags." REFERENCE "- Fibre Channel - Generic Services-5 (FC-GS-5), ANSI INCITS 427-2006, section 4.3.2.5." ::= { t11FcSpPoCtDescrEntry 5 } -- -- -- Switches/Nodes in Active Switch Connectivity Objects -- t11FcSpPoSwConnTable OBJECT-TYPE SYNTAX SEQUENCE OF T11FcSpPoSwConnEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table of active Switch Connectivity Objects. A Switch Connectivity Object defines to which other Switches or Nodes a particular Switch may/may not be connected at the Node level and/or at the Port level." REFERENCE "- ANSI INCITS 426-2007, T11/Project 1570-D, Fibre Channel - Security Protocols (FC-SP), February 2007, section 7.1.6.1, tables 123/124." ::= { t11FcSpPoActive 6 } t11FcSpPoSwConnEntry OBJECT-TYPE SYNTAX T11FcSpPoSwConnEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Each entry contains the name of either a Switch or a Node with which any port of a particular Switch, or a particular port of that Switch, is allowed or not allowed to be connected. The particular Switch is on the Fabric identified by t11FcSpPoFabricIndex and managed within the Fibre Channel management instance identified by fcmInstanceIndex." INDEX { fcmInstanceIndex, t11FcSpPoFabricIndex, t11FcSpPoSwConnSwitchName, t11FcSpPoSwConnAllowedType, t11FcSpPoSwConnPortNameOrAll, t11FcSpPoSwConnAllowedIndex } ::= { t11FcSpPoSwConnTable 1 } T11FcSpPoSwConnEntry ::= SEQUENCE { t11FcSpPoSwConnSwitchName FcNameIdOrZero, t11FcSpPoSwConnAllowedType INTEGER, t11FcSpPoSwConnPortNameOrAll FcNameIdOrZero, t11FcSpPoSwConnAllowedIndex Unsigned32, t11FcSpPoSwConnAllowedNameType T11FcSpPolicyNameType, t11FcSpPoSwConnAllowedName T11FcSpPolicyName } t11FcSpPoSwConnSwitchName OBJECT-TYPE SYNTAX FcNameIdOrZero (SIZE (8)) MAX-ACCESS not-accessible STATUS current DESCRIPTION "The name of the particular Switch for which this Switch Connectivity Object specifies topology restrictions." ::= { t11FcSpPoSwConnEntry 1 } t11FcSpPoSwConnAllowedType OBJECT-TYPE SYNTAX INTEGER { switch(1), node(2) } MAX-ACCESS not-accessible STATUS current DESCRIPTION "This object specifies whether this row refers to Switch-to-Switch or Switch-to-Node connectivity, i.e., whether the corresponding instance of t11FcSpPoSwConnAllowedName specifies the name of a Switch or the name of a Node." ::= { t11FcSpPoSwConnEntry 2 } t11FcSpPoSwConnPortNameOrAll OBJECT-TYPE SYNTAX FcNameIdOrZero (SIZE(0 | 8)) MAX-ACCESS not-accessible STATUS current DESCRIPTION "This object specifies either the particular port to which this topology restriction applies, or if the value is the zero-length string, that the topology restriction applies to all ports on the particular Switch. In the FC-SP Policy Database, restrictions for a particular port are formatted within a Port Connectivity Entry of a Switch Connectivity Object, whereas restrictions for all ports on the Switch are specified in the main part of a Switch Connectivity Object, i.e., not in a Port Connectivity Entry." REFERENCE "- ANSI INCITS 426-2007, T11/Project 1570-D, Fibre Channel - Security Protocols (FC-SP), February 2007, section 7.1.6.1, tables 123/124." ::= { t11FcSpPoSwConnEntry 3 } t11FcSpPoSwConnAllowedIndex OBJECT-TYPE SYNTAX Unsigned32 (1..4294967295) MAX-ACCESS not-accessible STATUS current DESCRIPTION "When multiple rows in this table apply to the same port(s) in the same Switch's Switch Connectivity Object, this object provides a unique index value to distinguish between such rows." ::= { t11FcSpPoSwConnEntry 4 } t11FcSpPoSwConnAllowedNameType OBJECT-TYPE SYNTAX T11FcSpPolicyNameType { nodeName(1), restrictedNodeName(2), portName(3), restrictedPortName(4), wildcard(5), restrictedWildcard(6) } MAX-ACCESS read-only STATUS current DESCRIPTION "If the value of this object is 'wildcard' or 'restrictedWildcard', this row specifies whether connectivity is allowed/not allowed with entities not explicitly named by other rows. Otherwise, the combination of t11FcSpPoSwConnAllowedNameType and t11FcSpPoSwConnAllowedName specify the name of: - a Switch (if t11FcSpPoSwConnAllowedType = 'switch'), or - a Node (if t11FcSpPoSwConnAllowedType = 'node') to which connectivity is: - allowed by 'nodeName' and 'portName', - not allowed by 'restrictedNodeName' and 'restrictedPortName'." ::= { t11FcSpPoSwConnEntry 5 } t11FcSpPoSwConnAllowedName OBJECT-TYPE SYNTAX T11FcSpPolicyName (SIZE (8)) MAX-ACCESS read-only STATUS current DESCRIPTION "If the value of t11FcSpPoSwConnAllowedNameType is 'wildcard' or 'restrictedWildcard', this object has the value '0000000000000000'h. Otherwise, the combination of t11FcSpPoSwConnAllowedNameType and t11FcSpPoSwConnAllowedName specify the name of: - a Switch (if t11FcSpPoSwConnAllowedType = 'switch'), or - a Node (if t11FcSpPoSwConnAllowedType = 'node') to which connectivity is allowed/restricted." ::= { t11FcSpPoSwConnEntry 6 } -- -- IP Management Entries in Active IP Management List Objects -- t11FcSpPoIpMgmtTable OBJECT-TYPE SYNTAX SEQUENCE OF T11FcSpPoIpMgmtEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table of IP Management Entries in active IP Management List Objects. An IP Management List Object is a Fabric-wide Policy Object that describes which IP hosts are allowed to manage a Fabric. One IP Management List Object is represented by all of the rows of this table that have the same values of fcmInstanceIndex and t11FcSpPoFabricIndex." REFERENCE "- ANSI INCITS 426-2007, T11/Project 1570-D, Fibre Channel - Security Protocols (FC-SP), February 2007, section 7.1.7" ::= { t11FcSpPoActive 7 } t11FcSpPoIpMgmtEntry OBJECT-TYPE SYNTAX T11FcSpPoIpMgmtEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Each entry contains information about one IP Management Entry within the active IP Management List Object for the Fabric identified by t11FcSpPoFabricIndex and managed within the Fibre Channel management instance identified by fcmInstanceIndex. The Policy Object Name of an IP Management Entry Policy Object is either an IPv6 Address Range or an IPv4 Address Range, where in each case, the range is specified as two addresses: the low and high ends of the range. In particular, since the Policy Object Name in this situation can only be an IPv6 Address Range or an IPv4 Address Range, it is represented here by three MIB objects defined as a (InetAddressType, InetAddress, InetAddress) tuple, in which the first address is the low end of the range, the second address is the high end of the range, and both addresses are of the type designated by InetAddressType. In theory, the use of t11FcSpPoIpMgmtEntryNameLow and t11FcSpPoIpMgmtEntryNameHigh (which both have the syntax of InetAddress) in the INDEX could cause the need for excessively long OIDs. In practice, this can't happen because FC-SP doesn't allow these objects to be specified as DNS names." INDEX { fcmInstanceIndex, t11FcSpPoFabricIndex, t11FcSpPoIpMgmtEntryNameType, t11FcSpPoIpMgmtEntryNameLow, t11FcSpPoIpMgmtEntryNameHigh } ::= { t11FcSpPoIpMgmtTable 1 } T11FcSpPoIpMgmtEntry ::= SEQUENCE { t11FcSpPoIpMgmtEntryNameType InetAddressType, t11FcSpPoIpMgmtEntryNameLow InetAddress, t11FcSpPoIpMgmtEntryNameHigh InetAddress, t11FcSpPoIpMgmtWkpIndex Unsigned32, t11FcSpPoIpMgmtAttribute T11FcSpAlphaNumNameOrAbsent } t11FcSpPoIpMgmtEntryNameType OBJECT-TYPE SYNTAX InetAddressType -- INTEGER { ipv4(1), ipv6(2) } MAX-ACCESS not-accessible STATUS current DESCRIPTION "The combination of t11FcSpPoIpMgmtNameType, t11FcSpPoIpMgmtNameLow, and t11FcSpPoIpMgmtNameHigh specify the Internet address range of this IP Management Entry in the IP Management List Object. The FC-SP specification does not allow the use of a DNS domain name to specify the address at the lower end or at the higher end of the Internet address range, nor does it allow the specification of a zone index. Therefore, the type of address must be one of: 'ipv4', or 'ipv6'." REFERENCE "- ANSI INCITS 426-2007, T11/Project 1570-D, Fibre Channel - Security Protocols (FC-SP), February 2007, sections 7.1.7.1 & 7.1.2, tables 103/126." ::= { t11FcSpPoIpMgmtEntry 1 } t11FcSpPoIpMgmtEntryNameLow OBJECT-TYPE SYNTAX InetAddress (SIZE(4 | 16)) MAX-ACCESS not-accessible STATUS current DESCRIPTION "The lower end of an Internet address range. The type of this address is given by the corresponding instance of t11FcSpPoIpMgmtEntryNameType. The combination of t11FcSpPoIpMgmtNameType, t11FcSpPoIpMgmtNameLow, and t11FcSpPoIpMgmtNameHigh specify the Internet address range of this IP Management Entry in the IP Management List Object." REFERENCE "- ANSI INCITS 426-2007, T11/Project 1570-D, Fibre Channel - Security Protocols (FC-SP), February 2007, sections 7.1.7.1 & 7.1.2, tables 103/126." ::= { t11FcSpPoIpMgmtEntry 2 } t11FcSpPoIpMgmtEntryNameHigh OBJECT-TYPE SYNTAX InetAddress (SIZE(4 | 16)) MAX-ACCESS not-accessible STATUS current DESCRIPTION "The higher end of an Internet address range. The type of this address is given by the corresponding instance of t11FcSpPoIpMgmtEntryNameType. The combination of t11FcSpPoIpMgmtNameType, t11FcSpPoIpMgmtNameLow, and t11FcSpPoIpMgmtNameHigh specify the Internet address range of this IP Management Entry in the IP Management List Object." REFERENCE "- ANSI INCITS 426-2007, T11/Project 1570-D, Fibre Channel - Security Protocols (FC-SP), February 2007, sections 7.1.7.1 & 7.1.2, tables 103/126." ::= { t11FcSpPoIpMgmtEntry 3 } t11FcSpPoIpMgmtWkpIndex OBJECT-TYPE SYNTAX Unsigned32 (0..4294967295) MAX-ACCESS read-only STATUS current DESCRIPTION "This object identifies the restrictions for IP management access by IP hosts in this range of IP addresses, specified as the set of Well-Known Protocols Access Descriptors contained in those rows of the t11FcSpPoWkpDescrTable for which the value of t11FcSpPoWkpDescrSpecifierIndex is the same as the value of this object. A value of zero indicates that this IP Management Entry does not identify a Well-Known Protocols Access Specifier." REFERENCE "- ANSI INCITS 426-2007, T11/Project 1570-D, Fibre Channel - Security Protocols (FC-SP), February 2007, section 7.1.7.1 and tables 127/129." ::= { t11FcSpPoIpMgmtEntry 4 } t11FcSpPoIpMgmtAttribute OBJECT-TYPE SYNTAX T11FcSpAlphaNumNameOrAbsent MAX-ACCESS read-only STATUS current DESCRIPTION "The name of an active Attribute Policy Object that is defined for this IP Management entry or the zero-length string. The zero-length string indicates that no Attribute Policy Object is defined for this IP Management entry." REFERENCE "- ANSI INCITS 426-2007, T11/Project 1570-D, Fibre Channel - Security Protocols (FC-SP), February 2007, section 7.1.7.1 and table 128." ::= { t11FcSpPoIpMgmtEntry 5 } -- -- Well-Known Protocol Access Descriptors -- t11FcSpPoWkpDescrTable OBJECT-TYPE SYNTAX SEQUENCE OF T11FcSpPoWkpDescrEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table of the Well-Known Protocol Access Descriptors being used within active Policy Objects. A Well-Known Protocol Access Specifier is a list of Well-Known Protocol Access Descriptors each of which specifies a protocol number, a port number, and/or various flags specifying how IP management access is restricted. A Well-Known Protocol Transport Access Specifier is represented by all rows of this table that have the same values of fcmInstanceIndex, t11FcSpPoFabricIndex, and t11FcSpPoWkpDescrSpecifierIndex." ::= { t11FcSpPoActive 8 } t11FcSpPoWkpDescrEntry OBJECT-TYPE SYNTAX T11FcSpPoWkpDescrEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Each entry contains information about one Well-Known Protocol Access Descriptor of a Well-Known Protocol Access Specifier used within the Fabric identified by t11FcSpPoFabricIndex and managed within the Fibre Channel management instance identified by fcmInstanceIndex." INDEX { fcmInstanceIndex, t11FcSpPoFabricIndex, t11FcSpPoWkpDescrSpecifierIndex, t11FcSpPoWkpDescrIndex } ::= { t11FcSpPoWkpDescrTable 1 } T11FcSpPoWkpDescrEntry ::= SEQUENCE { t11FcSpPoWkpDescrSpecifierIndex Unsigned32, t11FcSpPoWkpDescrIndex Unsigned32, t11FcSpPoWkpDescrFlags BITS, t11FcSpPoWkpDescrWkpNumber Unsigned32, t11FcSpPoWkpDescrDestPort InetPortNumber } t11FcSpPoWkpDescrSpecifierIndex OBJECT-TYPE SYNTAX Unsigned32 (1..4294967295) MAX-ACCESS not-accessible STATUS current DESCRIPTION "An index value that uniquely identifies a particular Well-Known Protocol Access Specifier within a Fabric." ::= { t11FcSpPoWkpDescrEntry 1 } t11FcSpPoWkpDescrIndex OBJECT-TYPE SYNTAX Unsigned32 (1..4294967295) MAX-ACCESS not-accessible STATUS current DESCRIPTION "An index value that uniquely identifies a particular Well-Known Protocol Access Descriptor within a Well-Known Protocol Access Specifier." ::= { t11FcSpPoWkpDescrEntry 2 } t11FcSpPoWkpDescrFlags OBJECT-TYPE SYNTAX BITS { allow(0), wkpWildcard(1), destPortWildcard(2), readOnly(3) } MAX-ACCESS read-only STATUS current DESCRIPTION "The flag bits that specify how access is to be limited by this Well-Known Protocol Access Descriptor: - allow -- IP management access using this protocol/port is allowed if this bit is set, and to be denied if this bit is not set. - wkpWildcard -- if this bit is set, the IP Protocol number of the Well-Known Protocol to be allowed/denied is specified by the value of t11FcSpPoWkpDescrWkpNumber. - destPortWildcard -- if this bit is set, the Destination (TCP/UDP) Port number of the Well-Known Protocol to be allowed/denied is specified by the value of t11FcSpPoWkpDescrDestPort. - readOnly -- if this bit is set, then access is to be granted only for reading." REFERENCE "- ANSI INCITS 426-2007, T11/Project 1570-D, Fibre Channel - Security Protocols (FC-SP), February 2007, section 7.1.7.1 and table 131." ::= { t11FcSpPoWkpDescrEntry 3 } t11FcSpPoWkpDescrWkpNumber OBJECT-TYPE SYNTAX Unsigned32 (0..255) MAX-ACCESS read-only STATUS current DESCRIPTION "When the 'wkpWildcard' bit is set in the corresponding instance of t11FcSpPoWkpDescrFlags, this object specifies the IP protocol number of the Well-Known Protocol." REFERENCE "- ANSI INCITS 426-2007, T11/Project 1570-D, Fibre Channel - Security Protocols (FC-SP), February 2007, section 7.1.7.1 and table 131. - http://www.iana.org/assignments/protocol-numbers." ::= { t11FcSpPoWkpDescrEntry 4 } t11FcSpPoWkpDescrDestPort OBJECT-TYPE SYNTAX InetPortNumber MAX-ACCESS read-only STATUS current DESCRIPTION "When the 'destPortWildcard' bit is set in the corresponding instance of t11FcSpPoWkpDescrFlags, this object specifies the Destination (TCP/UDP) Port number of the Well-Known Protocol. When the 'destPortWildcard' bit is reset, this object is ignored (and can have the value zero)." REFERENCE "- ANSI INCITS 426-2007, T11/Project 1570-D, Fibre Channel - Security Protocols (FC-SP), February 2007, section 7.1.7.1 and table 131. - http://www.iana.org/assignments/port-numbers." ::= { t11FcSpPoWkpDescrEntry 5 } -- -- Attribute Entries in Active Attribute Policy Objects -- t11FcSpPoAttribTable OBJECT-TYPE SYNTAX SEQUENCE OF T11FcSpPoAttribEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table of the Attribute Policy Objects being used within active Policy Objects. In the FC-SP Policy Database, each Attribute Policy Object consists of an Attribute Object Name and a set of Attribute Entries. An active Attribute Policy Object is represented by all the Attribute Entries in this table that have the same value of t11FcSpPoAttribName." ::= { t11FcSpPoActive 9 } t11FcSpPoAttribEntry OBJECT-TYPE SYNTAX T11FcSpPoAttribEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Each row contains information specific to an Attribute Entry contained within an Attribute Policy Object that is active within the Fabric identified by t11FcSpPoFabricIndex and managed within the Fibre Channel management instance identified by fcmInstanceIndex. For some types of Attribute Policy Objects, it is valuable to break out some semantically significant parts of the Policy Object's value into their own individual MIB objects; for example, to extract the one or more individual Authentication Protocol Identifiers and associated Authentication Protocol Parameters out of an Attribute Object containing a 'AUTH_Negotiate Message Payload'. For such types, another MIB table is defined to hold the extracted values in MIB objects specific to the Attribute Policy Object's type. In such cases, the t11FcSpPoAttribExtension object in this table points to the other MIB table. If the value of one Attribute Entry is too large (more than 256 bytes) to be contained within the value of one instance of t11FcSpPoAttribValue, then one row in this table contains the first 256 bytes, and one (or more) other row(s) in this table contain the rest of the value." INDEX { fcmInstanceIndex, t11FcSpPoFabricIndex, t11FcSpPoAttribName, t11FcSpPoAttribEntryIndex, t11FcSpPoAttribPartIndex } ::= { t11FcSpPoAttribTable 1 } T11FcSpPoAttribEntry ::= SEQUENCE { t11FcSpPoAttribName T11FcSpAlphaNumName, t11FcSpPoAttribEntryIndex Unsigned32, t11FcSpPoAttribPartIndex Unsigned32, t11FcSpPoAttribType Unsigned32, t11FcSpPoAttribValue OCTET STRING, t11FcSpPoAttribExtension OBJECT IDENTIFIER } t11FcSpPoAttribName OBJECT-TYPE SYNTAX T11FcSpAlphaNumName MAX-ACCESS not-accessible STATUS current DESCRIPTION "The name of the Attribute Policy Object containing one or more Attribute Entries." REFERENCE "- ANSI INCITS 426-2007, T11/Project 1570-D, Fibre Channel - Security Protocols (FC-SP), February 2007, section 7.1.8.1 and table 133." ::= { t11FcSpPoAttribEntry 1 } t11FcSpPoAttribEntryIndex OBJECT-TYPE SYNTAX Unsigned32 (1..4294967295) MAX-ACCESS not-accessible STATUS current DESCRIPTION "A unique value to distinguish this Attribute Entry from other Attribute Entries contained in the same Attribute Policy Object." REFERENCE "- ANSI INCITS 426-2007, T11/Project 1570-D, Fibre Channel - Security Protocols (FC-SP), February 2007, section 7.1.8.1, tables 133/134." ::= { t11FcSpPoAttribEntry 2 } t11FcSpPoAttribPartIndex OBJECT-TYPE SYNTAX Unsigned32 (1..4294967295) MAX-ACCESS not-accessible STATUS current DESCRIPTION "When the value of an Attribute Entry is shorter than 257 bytes, the whole value is contained in one instance of t11FcSpPoAttribValue, and the value of this object is 1. If the value of an Attribute Entry is longer than 256 bytes, then that value is divided up on 256-byte boundaries such that all parts are 256 bytes long except the last part, which is shorter if necessary, with each such part contained in a separate row of this table, and the value of this object is set to the part number. That is, this object has the value of 1 for bytes 0-255, the value of 2 for bytes 256-511, etc." REFERENCE "- ANSI INCITS 426-2007, T11/Project 1570-D, Fibre Channel - Security Protocols (FC-SP), February 2007, section 7.1.8.1, tables 134/135." ::= { t11FcSpPoAttribEntry 3 } t11FcSpPoAttribType OBJECT-TYPE SYNTAX Unsigned32 (1..4294967295) MAX-ACCESS read-only STATUS current DESCRIPTION "The type of attribute. The first type to be defined is: t11FcSpPoAttribType t11FcSpPoAttribValue =================== ==================== '00000001'h The AUTH_Negotiate Message Payload " REFERENCE "- ANSI INCITS 426-2007, T11/Project 1570-D, Fibre Channel - Security Protocols (FC-SP), February 2007, section 7.1.8.1, tables 134/135 and table 10." ::= { t11FcSpPoAttribEntry 4 } t11FcSpPoAttribValue OBJECT-TYPE SYNTAX OCTET STRING (SIZE (0..256)) MAX-ACCESS read-only STATUS current DESCRIPTION "The value of an Attribute Entry is divided up on 256-byte boundaries such that all parts are 256 bytes long except the last part, which is shorter if necessary, and each such part is contained in a separate instance of this object. The value of this object is independent of whether some parts of its value are broken out into separate MIB objects pointed to by the corresponding instance of t11FcSpPoAttribExtension." REFERENCE "- ANSI INCITS 426-2007, T11/Project 1570-D, Fibre Channel - Security Protocols (FC-SP), February 2007, section 7.1.8.1, tables 134/135 and table 10." ::= { t11FcSpPoAttribEntry 5 } t11FcSpPoAttribExtension OBJECT-TYPE SYNTAX OBJECT IDENTIFIER MAX-ACCESS read-only STATUS current DESCRIPTION "For some types of Attribute Policy Object, the value of this MIB object points to type-specific MIB objects that contain individual/broken-out parts of the Attribute Policy Object's value. If this object doesn't point to such type-specific MIB objects, then it contains the value: zeroDotZero. In particular, when the value of t11FcSpPoAttribType indicates 'AUTH_Negotiate Message Payload', one or more Authentication Protocol Identifiers and their associated Authentication Protocol Parameters are embedded within the value of the corresponding instance of t11FcSpPoAttribValue; MIB objects to contain these individual values are defined in the t11FcSpPoAuthProtTable. Thus, for an 'AUTH_Negotiate Message Payload' Attribute, the value of this object contains an OID within the t11FcSpPoAuthProtTable, e.g., of the whole table, of an individual row, or of an individual instance within the table." ::= { t11FcSpPoAttribEntry 6 } -- -- Auth. Protocol Parameters in Active Attribute Policy Objects -- t11FcSpPoAuthProtTable OBJECT-TYPE SYNTAX SEQUENCE OF T11FcSpPoAuthProtEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table of Authentication Protocol Identifier and Authentication Protocol Parameters that are embedded in Attribute Policy Objects being used within active Policy Objects. This table is used for Attribute Entries of Attribute Policy Objects for which the value of t11FcSpPoAttribType indicates 'AUTH_Negotiate Message Payload' and the value of t11FcSpPoAttribExtension contains the OID of this table." REFERENCE "- ANSI INCITS 426-2007, T11/Project 1570-D, Fibre Channel - Security Protocols (FC-SP), February 2007, sections 5.3.2 & 7.1.8.1, tables 134/135 and tables 10/11." ::= { t11FcSpPoActive 10 } t11FcSpPoAuthProtEntry OBJECT-TYPE SYNTAX T11FcSpPoAuthProtEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Each entry contains information about an Authentication Protocol that is extracted out of the Attribute Entry (identified by t11FcSpPoAttribEntryIndex) of the Policy Attribute Object (identified by t11FcSpPoAttribName), which is active within the Fabric identified by t11FcSpPoFabricIndex and managed within the Fibre Channel management instance identified by fcmInstanceIndex. If the value of one Attribute Protocol Parameters string is too large (more than 256 bytes) to be contained within the value of one instance of t11FcSpPoAuthProtParams, then one row in this table contains the first 256 bytes, and one (or more) other row(s) in this table contain the rest of the value." INDEX { fcmInstanceIndex, t11FcSpPoFabricIndex, t11FcSpPoAttribName, t11FcSpPoAttribEntryIndex, t11FcSpPoAuthProtIdentifier, t11FcSpPoAuthProtPartIndex } ::= { t11FcSpPoAuthProtTable 1 } T11FcSpPoAuthProtEntry ::= SEQUENCE { t11FcSpPoAuthProtIdentifier Unsigned32, t11FcSpPoAuthProtPartIndex Unsigned32, t11FcSpPoAuthProtParams OCTET STRING } t11FcSpPoAuthProtIdentifier OBJECT-TYPE SYNTAX Unsigned32 (0..4294967295) MAX-ACCESS not-accessible STATUS current DESCRIPTION "The Authentication Protocol Identifier: 1 = DH-CHAP 2 = FCAP 3 = FCPAP 4 = IKEv2 5 = IKEv2-AUTH 240 thru 255 = Vendor Specific Protocols all other values are 'Reserved' (by T11)." REFERENCE "- ANSI INCITS 426-2007, T11/Project 1570-D, Fibre Channel - Security Protocols (FC-SP), February 2007, section 5.3.2, table 11." ::= { t11FcSpPoAuthProtEntry 1 } t11FcSpPoAuthProtPartIndex OBJECT-TYPE SYNTAX Unsigned32 (1..4294967295) MAX-ACCESS not-accessible STATUS current DESCRIPTION "When the value of an Attribute Protocol Parameters string is shorter than 257 bytes, the whole value is contained in one instance of t11FcSpPoAuthProtParams, and the value of this object is 1. (This includes the case when the Attribute Protocol Parameters string is zero bytes in length.) If the value of an Authentication Protocol Parameters string is longer than 256 bytes, then that value is divided up on 256-byte boundaries such that all parts are 256 bytes long except the last part, which is shorter if necessary, with each such part contained in a separate row of this table, and the value of this object is set to the part number. That is, this object has the value of 1 for bytes 0-255, the value of 2 for bytes 256-511, etc." REFERENCE "- ANSI INCITS 426-2007, T11/Project 1570-D, Fibre Channel - Security Protocols (FC-SP), February 2007, section 5.3.2, table 10." ::= { t11FcSpPoAuthProtEntry 2 } t11FcSpPoAuthProtParams OBJECT-TYPE SYNTAX OCTET STRING (SIZE (0..256)) MAX-ACCESS read-only STATUS current DESCRIPTION "The value of an Authentication Protocol Parameters string is divided up on 256-byte boundaries such that all parts are 256 bytes long except the last part, which is shorter if necessary, and each such part is contained in a separate instance of this object." REFERENCE "- ANSI INCITS 426-2007, T11/Project 1570-D, Fibre Channel - Security Protocols (FC-SP), February 2007, section 5.3.2, table 10." ::= { t11FcSpPoAuthProtEntry 3 } -- -- Part 2 - Activate/De-Activate Operations -- -- -- Objects to Invoke Activate/De-Activate Operations -- t11FcSpPoOperTable OBJECT-TYPE SYNTAX SEQUENCE OF T11FcSpPoOperEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table that allows Activate and Deactivate operations to be invoked for FC-SP Policies on various Fabrics. Activating a new policy configuration is a two-step process: 1) create a single Policy Summary Object as a set of rows in the t11FcSpPoNaSummaryTable specifying a set of Policy Objects that describe the new configuration; and 2) activate that Policy Summary Object using the t11FcSpPoOperActivate object defined in this table. Deactivating the current policy configuration is a one-step process: the current Policy Summary Object is deactivated using the t11FcSpPoOperDeActivate object." ::= { t11FcSpPoOperations 1 } t11FcSpPoOperEntry OBJECT-TYPE SYNTAX T11FcSpPoOperEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Each entry allows an Activate and/or Deactivate operation to be invoked on a particular Fabric, which is managed as part of the Fibre Channel management instance identified by fcmInstanceIndex." INDEX { fcmInstanceIndex, t11FcSpPoFabricIndex } ::= { t11FcSpPoOperTable 1 } T11FcSpPoOperEntry ::= SEQUENCE { t11FcSpPoOperActivate T11FcSpAlphaNumName, t11FcSpPoOperDeActivate T11FcSpAlphaNumName, t11FcSpPoOperResult INTEGER, t11FcSpPoOperFailCause SnmpAdminString } t11FcSpPoOperActivate OBJECT-TYPE SYNTAX T11FcSpAlphaNumName MAX-ACCESS read-write STATUS current DESCRIPTION "Writing the name of a Policy Summary Object into this object is a request to activate the policy configuration described by the combination of all rows in t11FcSpPoNaSummaryTable that have that name as their value of t11FcSpPoNaSummaryName and are for the same Fabric. Before issuing such a request, the relevant rows in the t11FcSpPoNaSummaryTable must exist and represent a complete and consistent Policy Summary Object. If they do not, the request will fail, with t11FcSpPoOperResult having the 'badSummaryObject' value. When read, the value of this object is always the zero- length string. Writing to this object does not delete (or in any way affect) any rows in the MIB tables for non-active Policy Objects." REFERENCE "- ANSI INCITS 426-2007, T11/Project 1570-D, Fibre Channel - Security Protocols (FC-SP), February 2007, section 7.3.6.2" ::= { t11FcSpPoOperEntry 1 } t11FcSpPoOperDeActivate OBJECT-TYPE SYNTAX T11FcSpAlphaNumName MAX-ACCESS read-write STATUS current DESCRIPTION "Writing the current value of t11FcSpPoPolicySummaryObjName into this object (for a particular Fabric) is a request to deactivate that Fabric's current policy configuration. Writing any other value into this object is an error (e.g., 'wrongValue'). When read, the value of this object is always the zero- length string." REFERENCE "- ANSI INCITS 426-2007, T11/Project 1570-D, Fibre Channel - Security Protocols (FC-SP), February 2007, section 7.3.6.3" ::= { t11FcSpPoOperEntry 2 } t11FcSpPoOperResult OBJECT-TYPE SYNTAX INTEGER { activateSuccess(1), badSummaryObject(2), activateFailure(3), deactivateSuccess(4), deactivateFailure(5), inProgress(6), none(7) } MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the status/result of the last activation/deactivation that was invoked via the corresponding instance of t11FcSpPoOperActivate or t11FcSpPoOperDeActivate. When the value of this object is 'inProgress', the values of the corresponding instances of t11FcSpPoOperActivate and t11FcSpPoOperDeActivate cannot be modified. The value 'badSummaryObject' indicates an activation request that did not name a complete and consistent Policy Summary Object. The value 'none' indicates activation/deactivation has not been attempted since the last restart of the management system." ::= { t11FcSpPoOperEntry 3 } t11FcSpPoOperFailCause OBJECT-TYPE SYNTAX SnmpAdminString (SIZE (0..64)) MAX-ACCESS read-only STATUS current DESCRIPTION "A textual message indicating the reason for the most recent activation/deactivation failure, or the zero-length string if no information is available (e.g., because the corresponding instance of t11FcSpPoOperResult has the value 'none'). When the corresponding instance of t11FcSpPoOperResult is either 'activateFailure' or 'deactivateFailure', the value of this object indicates the reason for that failure." ::= { t11FcSpPoOperEntry 4 } -- -- Part 3 - Non-Active Policy Objects -- -- -- Non-Active Policy Summary Objects Available for Activation -- t11FcSpPoNaSummaryTable OBJECT-TYPE SYNTAX SEQUENCE OF T11FcSpPoNaSummaryEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table of non-active Policy Summary Objects available to be activated. The functionality of this table deviates slightly from FC-SP in that FC-SP specifies that the only Policy Summary Object is the Active one, i.e., FC-SP does not store non-active Policy Summary Objects in the Policy Database. Instead, FC-SP requires a new Policy Summary Object to be created for, and embedded within, every Activate (APS) request. Thus, the newly created Policy Summary Object outlasts the APS request only as the new active Policy Summary Object and only if the APS succeeds. In contrast, the Activate operation provided by this MIB module consists of two steps: 1) create a non-active Policy Summary Object as a set of entries in this table describing a new configuration; 2) activate a Policy Summary Object (stored as a set of entries in this table) using t11FcSpPoOperActivate. These two steps are only loosely connected, i.e., the result of the first operation is a non-active Policy Summary Object that is retained (in this table) even if it isn't immediately activated. Even after an attempt to activate it succeeds or fails, a non-active Policy Summary Object is not deleted, but is retained and still available for subsequent modification/re-use." ::= { t11FcSpPoNonActive 1 } t11FcSpPoNaSummaryEntry OBJECT-TYPE SYNTAX T11FcSpPoNaSummaryEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Each entry contains information about one non-active Policy Object within a non-active Policy Summary Object defined for potential use on the Fabric identified by t11FcSpPoFabricIndex, and managed within the Fibre Channel management instance identified by fcmInstanceIndex. A non-active Policy Summary Object is described by a set of entries in this table that have the same value of t11FcSpPoNaSummaryName. As and when a Policy Summary Object is activated using the t11FcSpPoOperActivate object, if the activation is successful, existing rows (if any) in MIB tables for active Policy Objects are deleted and replaced by the appropriate new set of rows. Existing rows in this table and/or in other tables for non-active Policy Objects are not affected by the activate operation. The StorageType of a row in this table is specified by the instance of t11FcSpPoStorageType that is INDEX-ed by the same values of fcmInstanceIndex and t11FcSpPoFabricIndex." REFERENCE "- ANSI INCITS 426-2007, T11/Project 1570-D, Fibre Channel - Security Protocols (FC-SP), February 2007, section 7.1.3 and table 104." INDEX { fcmInstanceIndex, t11FcSpPoFabricIndex, t11FcSpPoNaSummaryName, t11FcSpPoNaSummaryPolicyType, t11FcSpPoNaSummaryPolicyIndex } ::= { t11FcSpPoNaSummaryTable 1 } T11FcSpPoNaSummaryEntry ::= SEQUENCE { t11FcSpPoNaSummaryName T11FcSpAlphaNumName, t11FcSpPoNaSummaryPolicyType T11FcSpPolicyObjectType, t11FcSpPoNaSummaryPolicyIndex Unsigned32, t11FcSpPoNaSummaryPolicyNameType T11FcSpPolicyNameType, t11FcSpPoNaSummaryPolicyName T11FcSpPolicyName, t11FcSpPoNaSummaryHashStatus T11FcSpHashCalculationStatus, t11FcSpPoNaSummaryHashFormat T11FcSpPolicyHashFormat, t11FcSpPoNaSummaryHashValue T11FcSpPolicyHashValue, t11FcSpPoNaSummaryRowStatus RowStatus } t11FcSpPoNaSummaryName OBJECT-TYPE SYNTAX T11FcSpAlphaNumName MAX-ACCESS not-accessible STATUS current DESCRIPTION "The name of the non-active Policy Summary Object that contains this Policy Object." ::= { t11FcSpPoNaSummaryEntry 1 } t11FcSpPoNaSummaryPolicyType OBJECT-TYPE SYNTAX T11FcSpPolicyObjectType MAX-ACCESS not-accessible STATUS current DESCRIPTION "The 'Identifier' (i.e., the type) of this Policy Object." REFERENCE "- ANSI INCITS 426-2007, T11/Project 1570-D, Fibre Channel - Security Protocols (FC-SP), February 2007, section 7.1.3.1 and table 104." ::= { t11FcSpPoNaSummaryEntry 2 } t11FcSpPoNaSummaryPolicyIndex OBJECT-TYPE SYNTAX Unsigned32 (1..4294967295) MAX-ACCESS not-accessible STATUS current DESCRIPTION "A unique integer value to distinguish this Policy Object from any others that have the same type and that are contained in the same Policy Summary Object." ::= { t11FcSpPoNaSummaryEntry 3 } t11FcSpPoNaSummaryPolicyNameType OBJECT-TYPE SYNTAX T11FcSpPolicyNameType { nodeName(1), alphaNumericName(7) } MAX-ACCESS read-create STATUS current DESCRIPTION "The combination of t11FcSpPoNaSummaryPolicyNameType and t11FcSpPoNaSummaryPolicyName specify the name of the non-active Policy Object identified by this row. The type of name must be 'nodeName' if the value of the corresponding instance of t11FcSpPoNaSummaryPolicyType is 'switchConnectivity', or 'alphaNumericName' otherwise." ::= { t11FcSpPoNaSummaryEntry 4 } t11FcSpPoNaSummaryPolicyName OBJECT-TYPE SYNTAX T11FcSpPolicyName MAX-ACCESS read-create STATUS current DESCRIPTION "The combination of t11FcSpPoNaSummaryPolicyNameType and t11FcSpPoNaSummaryPolicyName specify the name of the non-active Policy Object identified by this row." ::= { t11FcSpPoNaSummaryEntry 5 } t11FcSpPoNaSummaryHashStatus OBJECT-TYPE SYNTAX T11FcSpHashCalculationStatus MAX-ACCESS read-create STATUS current DESCRIPTION "When read, the value of this object is either: correct -- the corresponding instance of t11FcSpPoNaSummaryHashValue contains the correct value; or stale -- the corresponding instance of t11FcSpPoNaSummaryHashValue contains a stale (possibly incorrect) value; Writing a value of 'calculate' is a request to re-calculate and update the value of the corresponding instance of t11FcSpPoNaSummaryHashValue. Writing a value of 'correct' or 'stale' to this object is an error (e.g., 'wrongValue')." DEFVAL { stale } ::= { t11FcSpPoNaSummaryEntry 6 } t11FcSpPoNaSummaryHashFormat OBJECT-TYPE SYNTAX T11FcSpPolicyHashFormat MAX-ACCESS read-only STATUS current DESCRIPTION "The format of this Policy Object's hash value as contained in the corresponding instance of the t11FcSpPoNaSummaryHashValue object." DEFVAL { '00000001'h } ::= { t11FcSpPoNaSummaryEntry 7 } t11FcSpPoNaSummaryHashValue OBJECT-TYPE SYNTAX T11FcSpPolicyHashValue MAX-ACCESS read-only STATUS current DESCRIPTION "The hash value of this Policy Object, in the format identified by the corresponding instance of the t11FcSpPoNaSummaryHashFormat object." DEFVAL { "" } ::= { t11FcSpPoNaSummaryEntry 8 } t11FcSpPoNaSummaryRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "The status of this row. Before a row in this table can have 'active' status, a non-Active Policy Object must already be represented in the table corresponding to the value of t11FcSpPoNaSummaryPolicyType with the name given by the combination of t11FcSpPoNaSummaryPolicyNameType and t11FcSpPoNaSummaryPolicyName. If such a Policy Object gets deleted from the relevant table, the row in this table must also get deleted. When a row has 'active' status, the only write-able MIB objects in this table are t11FcSpPoNaSummaryHashStatus and t11FcSpPoNaSummaryRowStatus." ::= { t11FcSpPoNaSummaryEntry 9 } -- -- Non-Active Switch Membership List Objects -- t11FcSpPoNaSwListTable OBJECT-TYPE SYNTAX SEQUENCE OF T11FcSpPoNaSwListEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table of non-active Switch Membership List Objects." REFERENCE "- ANSI INCITS 426-2007, T11/Project 1570-D, Fibre Channel - Security Protocols (FC-SP), February 2007, section 7.1.4.1 and table 108." ::= { t11FcSpPoNonActive 2 } t11FcSpPoNaSwListEntry OBJECT-TYPE SYNTAX T11FcSpPoNaSwListEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Each entry contains information about one non-active Switch Membership List Object for the Fabric identified by t11FcSpPoFabricIndex and managed within the Fibre Channel management instance identified by fcmInstanceIndex. The StorageType of a row in this table is specified by the instance of t11FcSpPoStorageType that is INDEX-ed by the same values of fcmInstanceIndex and t11FcSpPoFabricIndex." INDEX { fcmInstanceIndex, t11FcSpPoFabricIndex, t11FcSpPoNaSwListName } ::= { t11FcSpPoNaSwListTable 1 } T11FcSpPoNaSwListEntry ::= SEQUENCE { t11FcSpPoNaSwListName T11FcSpAlphaNumName, t11FcSpPoNaSwListFabricName FcNameIdOrZero, t11FcSpPoNaSwListRowStatus RowStatus } t11FcSpPoNaSwListName OBJECT-TYPE SYNTAX T11FcSpAlphaNumName MAX-ACCESS not-accessible STATUS current DESCRIPTION "The name of the Switch Membership List Object." REFERENCE "- ANSI INCITS 426-2007, T11/Project 1570-D, Fibre Channel - Security Protocols (FC-SP), February 2007, section 7.1.4.1 and table 108." ::= { t11FcSpPoNaSwListEntry 1 } t11FcSpPoNaSwListFabricName OBJECT-TYPE SYNTAX FcNameIdOrZero MAX-ACCESS read-create STATUS current DESCRIPTION "The administratively specified Fabric_Name. This value is meaningful only when static Domain_IDs are used in a Fabric. If Static Domain_IDs are not used, the Fabric_Name is dynamically determined, in which case the value of this object can be '0000000000000000'h or the zero-length string." REFERENCE "- t11FamConfigDomainId, T11-FC-FABRIC-ADDR-MGR-MIB, Fibre Channel Fabric Address Manager MIB, RFC 4439; - ANSI INCITS 426-2007, T11/Project 1570-D, Fibre Channel - Security Protocols (FC-SP), February 2007, table 108." ::= { t11FcSpPoNaSwListEntry 2 } t11FcSpPoNaSwListRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "The status of this row. Values of object instances within the row can be modified at any time. If a row in this table is deleted, any row in the t11FcSpPoNaSwMembTable for the same Switch Membership List Object will also get deleted." ::= { t11FcSpPoNaSwListEntry 3 } -- -- Switch Entries in Non-Active Switch Membership List Objects -- t11FcSpPoNaSwMembTable OBJECT-TYPE SYNTAX SEQUENCE OF T11FcSpPoNaSwMembEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table of Switch Entries in non-active Switch Membership List Objects." REFERENCE "- ANSI INCITS 426-2007, T11/Project 1570-D, Fibre Channel - Security Protocols (FC-SP), February 2007, section 7.1.4.1 and table 110." ::= { t11FcSpPoNonActive 3 } t11FcSpPoNaSwMembEntry OBJECT-TYPE SYNTAX T11FcSpPoNaSwMembEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Each entry contains information about one Switch that is listed in a Switch Entry of a non-active Switch Membership List Object for the Fabric identified by t11FcSpPoFabricIndex and managed within the Fibre Channel management instance identified by fcmInstanceIndex. A row cannot exist unless there is a row in t11FcSpPoNaSwListTable for the given Switch Membership List Object, i.e., the row in t11FcSpPoNaSwListTable for a Switch Membership List Object must be created before (or simultaneously with) a row in this table for a Switch Entry in that Switch Membership List Object, and when a row in t11FcSpPoNaSwListTable is deleted, all rows in this table for Switch Entries in that Switch Membership List Object also get deleted. The StorageType of a row in this table is specified by the instance of t11FcSpPoStorageType that is INDEX-ed by the same values of fcmInstanceIndex and t11FcSpPoFabricIndex." INDEX { fcmInstanceIndex, t11FcSpPoFabricIndex, t11FcSpPoNaSwListName, t11FcSpPoNaSwMembSwitchNameType, t11FcSpPoNaSwMembSwitchName } ::= { t11FcSpPoNaSwMembTable 1 } T11FcSpPoNaSwMembEntry ::= SEQUENCE { t11FcSpPoNaSwMembSwitchNameType T11FcSpPolicyNameType, t11FcSpPoNaSwMembSwitchName FcNameIdOrZero, t11FcSpPoNaSwMembFlags BITS, t11FcSpPoNaSwMembDomainID FcDomainIdOrZero, t11FcSpPoNaSwMembPolicyDataRole INTEGER, t11FcSpPoNaSwMembAuthBehaviour BITS, t11FcSpPoNaSwMembAttribute T11FcSpAlphaNumNameOrAbsent, t11FcSpPoNaSwMembRowStatus RowStatus } t11FcSpPoNaSwMembSwitchNameType OBJECT-TYPE SYNTAX T11FcSpPolicyNameType { nodeName(1), restrictedNodeName(2), wildcard(5), restrictedWildcard(6) } MAX-ACCESS not-accessible STATUS current DESCRIPTION "If the value of this object is 'nodeName' or 'restrictedNodeName', then the combination of this object and t11FcSpPoNaSwMembSwitchName specify the Switch Name of this Switch Entry. The membership is restricted or unrestricted based on the name type. Restricted membership means that the Switch is not allowed to be part of the Fabric unless allowed by a specific Switch Connectivity Object. Unrestricted membership means that the Switch is allowed to be part of the Fabric unless disallowed by a specific Switch Connectivity Object. The values of 'wildcard' and 'restrictedWildcard' provide the means to specify whether to allow/deny membership for Switches not explicitly named in the Switch Membership List Object." REFERENCE "- ANSI INCITS 426-2007, T11/Project 1570-D, Fibre Channel - Security Protocols (FC-SP), February 2007, section 7.1.4.1 and table 110." ::= { t11FcSpPoNaSwMembEntry 1 } t11FcSpPoNaSwMembSwitchName OBJECT-TYPE SYNTAX FcNameIdOrZero (SIZE (8)) MAX-ACCESS not-accessible STATUS current DESCRIPTION "If the value of t11FcSpPoSwMembSwitchNameType is 'wildcard' or 'restrictedWildcard', this object has the value '0000000000000000'h. Otherwise, the combination of t11FcSpPoNaSwMembSwitchNameType and this object specify the Switch Name of this Switch Entry." REFERENCE "- ANSI INCITS 426-2007, T11/Project 1570-D, Fibre Channel - Security Protocols (FC-SP), February 2007, section 7.1.4.1 and table 110." ::= { t11FcSpPoNaSwMembEntry 2 } t11FcSpPoNaSwMembFlags OBJECT-TYPE SYNTAX BITS { staticDomainID(0), insistentDomainID(1), serialPortsAccess(2), physicalPortsAccess(3), managerRole(4) } MAX-ACCESS read-create STATUS current DESCRIPTION "Configurable options in respect to the administration of Policy Objects at this Switch: 'staticDomainID' - the Switch uses the 'Static Domain_IDs behavior' (as defined in FC-SW-4) when this bit is set. This bit should have the same setting for all Switches in a Fabric's Switch Membership List Object, or else the Fabric will partition. If this bit is set, the 'insistentDomainID' bit must not be set. 'insistentDomainID' - if this bit is set, the Switch uses the 'Insistent Domain_IDs behavior' (as defined in FC-SW-4), and the 'staticDomainID' bit must not be set. 'serialPortsAccess' - the Switch allows management through serial ports when and only when this bit is set. 'physicalPortsAccess' - the Switch allows management through the physical panel when and only when this bit is set. 'managerRole' - the Switch is allowed to change the Fabric Policy configuration (on receipt of any of the EACA, ESFC, EUFC, ACA, SFC, or UFC SW_ILSs) if this bit is set." REFERENCE "- ANSI INCITS 426-2007, T11/Project 1570-D, Fibre Channel - Security Protocols (FC-SP), February 2007, section 7.1.4.1 and table 112." ::= { t11FcSpPoNaSwMembEntry 3 } t11FcSpPoNaSwMembDomainID OBJECT-TYPE SYNTAX FcDomainIdOrZero MAX-ACCESS read-create STATUS current DESCRIPTION "The Domain_ID to be used when either the 'staticDomainID' bit or the 'insistentDomainID' bit is set in the corresponding value of t11FcSpPoNaSwMembFlags." REFERENCE "- ANSI INCITS 426-2007, T11/Project 1570-D, Fibre Channel - Security Protocols (FC-SP), February 2007, section 7.1.4.1 and tables 111 and 112." ::= { t11FcSpPoNaSwMembEntry 4 } t11FcSpPoNaSwMembPolicyDataRole OBJECT-TYPE SYNTAX INTEGER { client(1), autonomous(2), server(3) } MAX-ACCESS read-create STATUS current DESCRIPTION "The role of the Switch in terms of which Policy data it retains/maintains: 'client' - the Switch operates as a Client Switch. A Client Switch maintains its own Switch Connectivity Object and all Fabric-wide List Objects. If FC-SP Zoning is used, a Client Switch maintains only the subset of the Active Zone Set that it requires to enforce the current Fabric Zoning configuration. 'autonomous' - the Switch operates as an Autonomous Switch. An Autonomous Switch maintains its own Switch Connectivity Object and all Fabric-wide List Objects. This is the same as 'client' except that if FC-SP Zoning is used, an Autonomous Switch maintains a complete copy of the Fabric Zoning Database. 'server' - the Switch operates as a Server Switch. A Server Switch maintains all Fabric-wide List Objects and the Switch Connectivity Objects of each Switch in the Fabric. If FC-SP Zoning is used, a Server Switch maintains a complete copy of the Fabric Zoning Database." REFERENCE "- ANSI INCITS 426-2007, T11/Project 1570-D, Fibre Channel - Security Protocols (FC-SP), February 2007, section 7.1.4.1 and table 113." ::= { t11FcSpPoNaSwMembEntry 5 } t11FcSpPoNaSwMembAuthBehaviour OBJECT-TYPE SYNTAX BITS { mustAuthenticate(0), rejectIsFailure(1) } MAX-ACCESS read-create STATUS current DESCRIPTION "The authentication behaviour of the Switch: 'mustAuthenticate' - if this bit is set, all connections between this Switch and neighbor Switches must be authenticated. 'rejectIsFailure' - if this bit is set, the rejection of an AUTH_Negotiate message must be considered as an authentication failure by this Switch." REFERENCE "- ANSI INCITS 426-2007, T11/Project 1570-D, Fibre Channel - Security Protocols (FC-SP), February 2007, section 7.1.4.1 and table 114." ::= { t11FcSpPoNaSwMembEntry 6 } t11FcSpPoNaSwMembAttribute OBJECT-TYPE SYNTAX T11FcSpAlphaNumNameOrAbsent MAX-ACCESS read-create STATUS current DESCRIPTION "The name of a non-active Attribute Policy Object that is defined for this Switch. The zero-length string indicates that no non-active Attribute Policy Object is defined for this Switch. The effect of having no rows in the t11FcSpPoNaAttribTable for which the value of t11FcSpPoNaAttribName is the same as the value of this object, is the same as this object's value being the zero-length string." REFERENCE "- ANSI INCITS 426-2007, T11/Project 1570-D, Fibre Channel - Security Protocols (FC-SP), February 2007, section 7.1.4.1 and table 110." ::= { t11FcSpPoNaSwMembEntry 7 } t11FcSpPoNaSwMembRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "The status of this row. Values of object instances within the row can be modified at any time. A row cannot exist unless there is a row in the t11FcSpPoNaSwListTable for the Switch Membership List Object containing the Switch Entry for this Switch, i.e., the row in t11FcSpPoNaSwListTable for a Switch Membership List Object must be created before (or simultaneously) with a row in this table for a Switch Entry in that Switch Membership List Object; and when a row in t11FcSpPoNaSwListTable is deleted, any row in this table for a Switch Entry in that Switch Membership List Object also gets deleted." ::= { t11FcSpPoNaSwMembEntry 8 } -- -- Node Entries in Non-Active Node Membership List Objects -- t11FcSpPoNaNoMembTable OBJECT-TYPE SYNTAX SEQUENCE OF T11FcSpPoNaNoMembEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table of Node Entries in non-active Node Membership List Objects. One Node Membership List Object is represented by all the rows in this table that have the same value of t11FcSpPoNaNoMembListName." ::= { t11FcSpPoNonActive 4 } t11FcSpPoNaNoMembEntry OBJECT-TYPE SYNTAX T11FcSpPoNaNoMembEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Each entry contains information about one Node Entry of a non-active Node Membership List Object for the Fabric identified by t11FcSpPoFabricIndex and managed within the Fibre Channel management instance identified by fcmInstanceIndex. The StorageType of a row in this table is specified by the instance of t11FcSpPoStorageType that is INDEX-ed by the same values of fcmInstanceIndex and t11FcSpPoFabricIndex." INDEX { fcmInstanceIndex, t11FcSpPoFabricIndex, t11FcSpPoNaNoMembListName, t11FcSpPoNaNoMembNodeNameType, t11FcSpPoNaNoMembNodeName } ::= { t11FcSpPoNaNoMembTable 1 } T11FcSpPoNaNoMembEntry ::= SEQUENCE { t11FcSpPoNaNoMembListName T11FcSpAlphaNumName, t11FcSpPoNaNoMembNodeNameType T11FcSpPolicyNameType, t11FcSpPoNaNoMembNodeName FcNameIdOrZero, t11FcSpPoNaNoMembFlags BITS, t11FcSpPoNaNoMembCtAccessIndex Unsigned32, t11FcSpPoNaNoMembAttribute T11FcSpAlphaNumNameOrAbsent, t11FcSpPoNaNoMembRowStatus RowStatus } t11FcSpPoNaNoMembListName OBJECT-TYPE SYNTAX T11FcSpAlphaNumName MAX-ACCESS not-accessible STATUS current DESCRIPTION "The name of the non-active Node Membership List Object." REFERENCE "- ANSI INCITS 426-2007, T11/Project 1570-D, Fibre Channel - Security Protocols (FC-SP), February 2007, section 7.1.4.1 and table 116." ::= { t11FcSpPoNaNoMembEntry 1 } t11FcSpPoNaNoMembNodeNameType OBJECT-TYPE SYNTAX T11FcSpPolicyNameType { nodeName(1), restrictedNodeName(2), portName(3), restrictedPortName(4), wildcard(5), restrictedWildcard(6) } MAX-ACCESS not-accessible STATUS current DESCRIPTION "If the value of this object is 'wildcard' or 'restrictedWildcard', this Node Entry applies to Nodes not explicitly named in the Node Membership List Object. Otherwise, the combination of this object and t11FcSpPoNaNoMembNodeName specify the name of this Node Entry in the active Node Membership List Object. A Node is identified by its Node Name or by one or more of its Port Names. Restricted membership means that a Node is not allowed to be connected to the Fabric unless allowed by a specific Switch Connectivity Object. Unrestricted membership means that a Node is allowed to be connected to the Fabric unless disallowed by a specific Switch Connectivity Object." REFERENCE "- ANSI INCITS 426-2007, T11/Project 1570-D, Fibre Channel - Security Protocols (FC-SP), February 2007, section 7.1.4.1 and table 116." ::= { t11FcSpPoNaNoMembEntry 2 } t11FcSpPoNaNoMembNodeName OBJECT-TYPE SYNTAX FcNameIdOrZero (SIZE (8)) MAX-ACCESS not-accessible STATUS current DESCRIPTION "If the value of t11FcSpPoNaNoMembNodeNameType is 'wildcard' or 'restrictedWildcard', this object has the value '0000000000000000'h. Otherwise, the combination of t11FcSpPoNaNoMembNodeNameType and this object specify the name of this Node Entry is the active Node Membership List Object." REFERENCE "- ANSI INCITS 426-2007, T11/Project 1570-D, Fibre Channel - Security Protocols (FC-SP), February 2007, section 7.1.4.1 and table 116." ::= { t11FcSpPoNaNoMembEntry 3 } t11FcSpPoNaNoMembFlags OBJECT-TYPE SYNTAX BITS { scsiEnclosureAccess(0), authenticationRequired(1) } MAX-ACCESS read-create STATUS current DESCRIPTION "Configurable options in respect to the administration of Policy Objects at this Node: 'scsiEnclosureAccess' - the Node is allowed to control any Switch through SCSI Enclosure Services if this bit is set. If a Switch does not support SCSI Enclosure Services, this bit is ignored. 'authenticationRequired' - the Node is required to authenticate itself to any Switch to which it is connected if and only if this bit is set." REFERENCE "- ANSI INCITS 426-2007, T11/Project 1570-D, Fibre Channel - Security Protocols (FC-SP), February 2007, section 7.1.4.1 and table 118." ::= { t11FcSpPoNaNoMembEntry 4 } t11FcSpPoNaNoMembCtAccessIndex OBJECT-TYPE SYNTAX Unsigned32 (0..4294967295) MAX-ACCESS read-create STATUS current DESCRIPTION "If the value of this object is zero, then access by this Node to Generic Services is not limited by a Common Transport Access Specifier. Otherwise, the limits are specified by the set of Common Transport Access Descriptors contained in those rows of the t11FcSpPoNaCtDescrTable for which the value of t11FcSpPoNaCtDescrSpecifierIndex is the same as the value of this object. No such rows in t11FcSpPoNaCtDescrTable have the same effect as this object's value being zero." REFERENCE "- ANSI INCITS 426-2007, T11/Project 1570-D, Fibre Channel - Security Protocols (FC-SP), February 2007, section 7.1.4.1 and tables 118/119/120/121." ::= { t11FcSpPoNaNoMembEntry 5 } t11FcSpPoNaNoMembAttribute OBJECT-TYPE SYNTAX T11FcSpAlphaNumNameOrAbsent MAX-ACCESS read-create STATUS current DESCRIPTION "The name of a non-active Attribute Policy Object that is defined for this Node. The zero-length string indicates that no non-active Attribute Policy Object is defined for this Node. The effect of having no rows in the t11FcSpPoNaAttribTable for which the value of t11FcSpPoNaAttribName is the same as the value of this object, is the same as this object's value being the zero-length string." REFERENCE "- ANSI INCITS 426-2007, T11/Project 1570-D, Fibre Channel - Security Protocols (FC-SP), February 2007, section 7.1.4.1 and table 116." ::= { t11FcSpPoNaNoMembEntry 6 } t11FcSpPoNaNoMembRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "The status of this row. Values of object instances within the row can be modified at any time." ::= { t11FcSpPoNaNoMembEntry 7 } -- -- -- Non-Active Common Transport Access Descriptors -- t11FcSpPoNaCtDescrTable OBJECT-TYPE SYNTAX SEQUENCE OF T11FcSpPoNaCtDescrEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table of Common Transport Access Descriptors referenced by non-active Policy Objects. A Common Transport Access Specifier is a list of Common Transport Access Descriptors that specify whether a Node is allowed to access a Generic Service or Sub-Server. A non-active Common Transport Access Specifier is represented by all rows of this table that have the same values of fcmInstanceIndex, t11FcSpPoFabricIndex, and t11FcSpPoNaCtDescrSpecifierIndex." REFERENCE "- ANSI INCITS 426-2007, T11/Project 1570-D, Fibre Channel - Security Protocols (FC-SP), February 2007, section 7.1.5" ::= { t11FcSpPoNonActive 5 } t11FcSpPoNaCtDescrEntry OBJECT-TYPE SYNTAX T11FcSpPoNaCtDescrEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Each entry contains information about one Common Transport Access Descriptor of an non-active Common Transport Access Specifier used within the Fabric identified by t11FcSpPoFabricIndex and managed within the Fibre Channel management instance identified by fcmInstanceIndex. The StorageType of a row in this table is specified by the instance of t11FcSpPoStorageType that is INDEX-ed by the same values of fcmInstanceIndex and t11FcSpPoFabricIndex." INDEX { fcmInstanceIndex, t11FcSpPoFabricIndex, t11FcSpPoNaCtDescrSpecifierIndex, t11FcSpPoNaCtDescrIndex } ::= { t11FcSpPoNaCtDescrTable 1 } T11FcSpPoNaCtDescrEntry ::= SEQUENCE { t11FcSpPoNaCtDescrSpecifierIndex Unsigned32, t11FcSpPoNaCtDescrIndex Unsigned32, t11FcSpPoNaCtDescrFlags BITS, t11FcSpPoNaCtDescrGsType OCTET STRING, t11FcSpPoNaCtDescrGsSubType OCTET STRING, t11FcSpPoNaCtDescrRowStatus RowStatus } t11FcSpPoNaCtDescrSpecifierIndex OBJECT-TYPE SYNTAX Unsigned32 (1..4294967295) MAX-ACCESS not-accessible STATUS current DESCRIPTION "An index value that uniquely identifies a particular Common Transport Access Specifier within a Fabric." ::= { t11FcSpPoNaCtDescrEntry 1 } t11FcSpPoNaCtDescrIndex OBJECT-TYPE SYNTAX Unsigned32 (1..4294967295) MAX-ACCESS not-accessible STATUS current DESCRIPTION "An index value that uniquely identifies a particular Common Transport Access Descriptor within a Common Transport Access Specifier." ::= { t11FcSpPoNaCtDescrEntry 2 } t11FcSpPoNaCtDescrFlags OBJECT-TYPE SYNTAX BITS { allow(0), gsTypeWildcard(1), gsSubTypeWildcard(2), readOnly(3) } MAX-ACCESS read-create STATUS current DESCRIPTION "The flag bits that specify how access is to be limited by this Common Transport Access Descriptor: - allow -- access to the specified Generic Service and Server is allowed if this bit is set, and is to be denied if this bit is not set. - gsTypeWildcard -- if this bit is set, the Generic Service to be allowed/denied is specified by the value of t11FcSpPoNaCtDescrGsType, and the gsSubTypeWildcard bit must not also be set. - gsSubTypeWildcard -- if this bit is set, the Generic Service to be allowed/denied is specified by the value of t11FcSpPoNaCtDescrGsSubType, and the gsTypeWildcard bit must not also be set. - readOnly -- if this bit is set, then access is to be granted only for reading." REFERENCE "- ANSI INCITS 426-2007, T11/Project 1570-D, Fibre Channel - Security Protocols (FC-SP), February 2007, section 7.1.5.1, and tables 117, 118, and 120." ::= { t11FcSpPoNaCtDescrEntry 3 } t11FcSpPoNaCtDescrGsType OBJECT-TYPE SYNTAX OCTET STRING (SIZE (1)) MAX-ACCESS read-create STATUS current DESCRIPTION "The GS_Type of the Generic Service (e.g., the FC-GS-5 Management Service) that is subject to access control. This value is ignored if the gsTypeWildcard bit is not set in the corresponding value of t11FcSpPoNaCtDescrFlags." REFERENCE "- ANSI INCITS 427-2006, Fibre Channel - Generic Services-5 (FC-GS-5), section 4.3.2.4. - ANSI INCITS 426-2007, T11/Project 1570-D, Fibre Channel - Security Protocols (FC-SP), February 2007, section 7.1.5.1 and table 120." ::= { t11FcSpPoNaCtDescrEntry 4 } t11FcSpPoNaCtDescrGsSubType OBJECT-TYPE SYNTAX OCTET STRING (SIZE (1)) MAX-ACCESS read-create STATUS current DESCRIPTION "The GS_Subtype of the Generic Server (e.g., the Fabric Zone Server) that is subject to access control. This value is ignored if the gsSubTypeWildcard bit is not set in the corresponding value of t11FcSpPoNaCtDescrFlags." REFERENCE "- ANSI INCITS 427-2006, Fibre Channel - Generic Services-5 (FC-GS-5), section 4.3.2.5. - ANSI INCITS 426-2007, T11/Project 1570-D, Fibre Channel - Security Protocols (FC-SP), February 2007, section 7.1.5.1 and table 120." ::= { t11FcSpPoNaCtDescrEntry 5 } t11FcSpPoNaCtDescrRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "The status of this row. Values of object instances within the row can be modified at any time." ::= { t11FcSpPoNaCtDescrEntry 6 } -- -- Switches/Nodes in Non-Active Switch Connectivity Objects -- t11FcSpPoNaSwConnTable OBJECT-TYPE SYNTAX SEQUENCE OF T11FcSpPoNaSwConnEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table of non-active Switch Connectivity Objects. A Switch Connectivity Object defines to which other Switches or Nodes a particular Switch may/may not be connected at the Node level and/or at the Port level." REFERENCE "- ANSI INCITS 426-2007, T11/Project 1570-D, Fibre Channel - Security Protocols (FC-SP), February 2007, section 7.1.6." ::= { t11FcSpPoNonActive 6 } t11FcSpPoNaSwConnEntry OBJECT-TYPE SYNTAX T11FcSpPoNaSwConnEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Each entry contains the name of a Switch/Node with which any port of a particular Switch on a particular Fabric, or a particular port on that Switch, is allowed or not allowed to be connected. The particular Fabric is identified by t11FcSpPoFabricIndex and managed within the Fibre Channel management instance identified by fcmInstanceIndex. The StorageType of a row in this table is specified by the instance of t11FcSpPoStorageType that is INDEX-ed by the same values of fcmInstanceIndex and t11FcSpPoFabricIndex." INDEX { fcmInstanceIndex, t11FcSpPoFabricIndex, t11FcSpPoNaSwConnSwitchName, t11FcSpPoNaSwConnAllowedType, t11FcSpPoNaSwConnPortNameOrAll, t11FcSpPoNaSwConnAllowedIndex } ::= { t11FcSpPoNaSwConnTable 1 } T11FcSpPoNaSwConnEntry ::= SEQUENCE { t11FcSpPoNaSwConnSwitchName FcNameIdOrZero, t11FcSpPoNaSwConnAllowedType INTEGER, t11FcSpPoNaSwConnPortNameOrAll FcNameIdOrZero, t11FcSpPoNaSwConnAllowedIndex Unsigned32, t11FcSpPoNaSwConnAllowedNameType T11FcSpPolicyNameType, t11FcSpPoNaSwConnAllowedName FcNameIdOrZero, t11FcSpPoNaSwConnRowStatus RowStatus } t11FcSpPoNaSwConnSwitchName OBJECT-TYPE SYNTAX FcNameIdOrZero (SIZE (8)) MAX-ACCESS not-accessible STATUS current DESCRIPTION "The name of the Switch for which this Switch Connectivity Object specifies topology restrictions." REFERENCE "- ANSI INCITS 426-2007, T11/Project 1570-D, Fibre Channel - Security Protocols (FC-SP), February 2007, section 7.1.6.1 and table 123." ::= { t11FcSpPoNaSwConnEntry 1 } t11FcSpPoNaSwConnAllowedType OBJECT-TYPE SYNTAX INTEGER { switch(1), node(2) } MAX-ACCESS not-accessible STATUS current DESCRIPTION "This object specifies whether this row refers to an 'Allowed Switch' that concerns Switch-to-Switch connectivity or an 'Allowed Node' that concerns Switch-to-Node connectivity. Consequently, this object's value indicates whether the corresponding instance of t11FcSpPoNaSwConnAllowedName specifies the name of a Switch or the name of a Node." REFERENCE "- ANSI INCITS 426-2007, T11/Project 1570-D, Fibre Channel - Security Protocols (FC-SP), February 2007, section 7.1.6.1 and table 123." ::= { t11FcSpPoNaSwConnEntry 2 } t11FcSpPoNaSwConnPortNameOrAll OBJECT-TYPE SYNTAX FcNameIdOrZero (SIZE(0 | 8)) MAX-ACCESS not-accessible STATUS current DESCRIPTION "This object specifies either the particular port on which this topology restriction applies, or if the value is the zero-length string, that the topology restriction applies to all ports of the Switch. In other words, if this object's value contains the name of a port, then this row represents a 'Port Connectivity Entry' (as described in FC-SP) within a Switch Connectivity Object." REFERENCE "- ANSI INCITS 426-2007, T11/Project 1570-D, Fibre Channel - Security Protocols (FC-SP), February 2007, section 7.1.6.1 and tables 123/124." ::= { t11FcSpPoNaSwConnEntry 3 } t11FcSpPoNaSwConnAllowedIndex OBJECT-TYPE SYNTAX Unsigned32 (1..4294967295) MAX-ACCESS not-accessible STATUS current DESCRIPTION "When multiple rows in this table refer to different 'Allowed Switches' or to different 'Allowed Nodes' for the same port(s) in the same Switch Connectivity Object, this object provides a unique index value to distinguish between such rows." ::= { t11FcSpPoNaSwConnEntry 4 } t11FcSpPoNaSwConnAllowedNameType OBJECT-TYPE SYNTAX T11FcSpPolicyNameType { nodeName(1), restrictedNodeName(2), portName(3), restrictedPortName(4), wildcard(5), restrictedWildcard(6) } MAX-ACCESS read-create STATUS current DESCRIPTION "If the value of this object is 'wildcard' or 'restrictedWildcard', this row specifies whether connectivity is allowed/not allowed with entities not explicitly named by other rows. Otherwise, the combination of t11FcSpPoNaSwConnAllowedNameType and t11FcSpPoNaSwConnAllowedName specify the name of: - a Switch (if t11FcSpPoNaSwConnAllowedType = 'switch'), or - a Node (if t11FcSpPoNaSwConnAllowedType = 'node') to which connectivity is allowed/not allowed." REFERENCE "- ANSI INCITS 426-2007, T11/Project 1570-D, Fibre Channel - Security Protocols (FC-SP), February 2007, section 7.1.6.1 and tables 123/124." ::= { t11FcSpPoNaSwConnEntry 5 } t11FcSpPoNaSwConnAllowedName OBJECT-TYPE SYNTAX FcNameIdOrZero (SIZE (8)) MAX-ACCESS read-create STATUS current DESCRIPTION "If t11FcSpPoNaSwConnAllowedNameType has the value 'wildcard' or 'restrictedWildcard', this object has the value '0000000000000000'h. Otherwise, the combination of t11FcSpPoNaSwConnAllowedNameType and t11FcSpPoNaSwConnAllowedName specify the name of: - a Switch (if t11FcSpPoNaSwConnAllowedType = 'switch'), or - a Node (if t11FcSpPoNaSwConnAllowedType = 'node') to which connectivity is allowed/not allowed." REFERENCE "- ANSI INCITS 426-2007, T11/Project 1570-D, Fibre Channel - Security Protocols (FC-SP), February 2007, section 7.1.6.1 and tables 123/124." ::= { t11FcSpPoNaSwConnEntry 6 } t11FcSpPoNaSwConnRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "The status of this row. Values of object instances within the row can be modified at any time." ::= { t11FcSpPoNaSwConnEntry 7 } -- -- IP Management Entries in Non-Active IP Management List Objects -- t11FcSpPoNaIpMgmtTable OBJECT-TYPE SYNTAX SEQUENCE OF T11FcSpPoNaIpMgmtEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table of IP Management Entries in non-active IP Management List Objects. The IP Management List Object is a Fabric-wide Policy Object that describes which IP hosts are allowed to manage a Fabric. One non-active IP Management List Object is represented by all rows of this table that have the same values of fcmInstanceIndex and t11FcSpPoFabricIndex." ::= { t11FcSpPoNonActive 7 } t11FcSpPoNaIpMgmtEntry OBJECT-TYPE SYNTAX T11FcSpPoNaIpMgmtEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Each entry contains information about one IP Management entry within a non-active IP Management List Object for the Fabric identified by t11FcSpPoFabricIndex and managed within the Fibre Channel management instance identified by fcmInstanceIndex. The Policy Object Name of an IP Management Entry Policy Object is either an IPv6 Address Range or an IPv4 Address Range. In a Fabric's database of Policy Objects, every Policy Object Name, including these Internet address ranges, is represented as a (T11FcSpPolicyNameType, T11FcSpPolicyName) tuple. In contrast, this MIB module uses the conventional MIB syntax for IP addresses, and therefore represents the Policy Object Name of an IP Management Entry Policy Object as a (InetAddressType, InetAddress, InetAddress) tuple. In theory, the use of t11FcSpPoNaIpMgmtEntryNameLow and t11FcSpPoNaIpMgmtEntryNameHigh, which have the syntax of InetAddress, in the INDEX could cause the need for excessively long OIDs. In practice, this can't happen because FC-SP doesn't allow these objects to be specified as DNS names. The StorageType of a row in this table is specified by the instance of t11FcSpPoStorageType that is INDEX-ed by the same values of fcmInstanceIndex and t11FcSpPoFabricIndex." INDEX { fcmInstanceIndex, t11FcSpPoFabricIndex, t11FcSpPoNaIpMgmtListName, t11FcSpPoNaIpMgmtEntryNameType, t11FcSpPoNaIpMgmtEntryNameLow, t11FcSpPoNaIpMgmtEntryNameHigh } ::= { t11FcSpPoNaIpMgmtTable 1 } T11FcSpPoNaIpMgmtEntry ::= SEQUENCE { t11FcSpPoNaIpMgmtListName T11FcSpAlphaNumName, t11FcSpPoNaIpMgmtEntryNameType InetAddressType, t11FcSpPoNaIpMgmtEntryNameLow InetAddress, t11FcSpPoNaIpMgmtEntryNameHigh InetAddress, t11FcSpPoNaIpMgmtWkpIndex Unsigned32, t11FcSpPoNaIpMgmtAttribute T11FcSpAlphaNumNameOrAbsent, t11FcSpPoNaIpMgmtRowStatus RowStatus } t11FcSpPoNaIpMgmtListName OBJECT-TYPE SYNTAX T11FcSpAlphaNumName MAX-ACCESS not-accessible STATUS current DESCRIPTION "The name of a non-active Node Membership List Object." REFERENCE "- ANSI INCITS 426-2007, T11/Project 1570-D, Fibre Channel - Security Protocols (FC-SP), February 2007, section 7.1.7.1 and table 125." ::= { t11FcSpPoNaIpMgmtEntry 1 } t11FcSpPoNaIpMgmtEntryNameType OBJECT-TYPE SYNTAX InetAddressType { ipv4(1), ipv6(2) } MAX-ACCESS not-accessible STATUS current DESCRIPTION "The combination of t11FcSpPoNaIpMgmtEntryNameType, t11FcSpPoNaIpMgmtNameLow, and t11FcSpPoNaIpMgmtNameHigh specify the Internet address range of this IP Management Entry in the IP Management List Object. The FC-SP specification does not allow this address to be specified using a DNS domain name, nor does it allow the specification of zone indexes. Therefore, the type of address must be one of: 'ipv4' or 'ipv6'." REFERENCE "- ANSI INCITS 426-2007, T11/Project 1570-D, Fibre Channel - Security Protocols (FC-SP), February 2007, sections 7.1.7.1 and table 126." ::= { t11FcSpPoNaIpMgmtEntry 2 } t11FcSpPoNaIpMgmtEntryNameLow OBJECT-TYPE SYNTAX InetAddress (SIZE(4 | 16)) MAX-ACCESS not-accessible STATUS current DESCRIPTION "The lower end of an Internet address range. The type of this address is given by the corresponding instance of t11FcSpPoNaIpMgmtEntryNameType. The combination of t11FcSpPoNaIpMgmtEntryNameType, t11FcSpPoNaIpMgmtNameLow, and t11FcSpPoIpMgmtNameHigh specify the Internet address range of this IP Management Entry in the IP Management List Object." REFERENCE "- ANSI INCITS 426-2007, T11/Project 1570-D, Fibre Channel - Security Protocols (FC-SP), February 2007, sections 7.1.7.1 and table 126." ::= { t11FcSpPoNaIpMgmtEntry 3 } t11FcSpPoNaIpMgmtEntryNameHigh OBJECT-TYPE SYNTAX InetAddress (SIZE(4 | 16)) MAX-ACCESS not-accessible STATUS current DESCRIPTION "The higher end of an Internet address range. The type of this address is given by the corresponding instance of t11FcSpPoNaIpMgmtEntryNameType. The combination of t11FcSpPoNaIpMgmtEntryNameType, t11FcSpPoNaIpMgmtNameLow, and t11FcSpPoNaIpMgmtNameHigh specify the Internet address range of this IP Management Entry in the IP Management List Object." REFERENCE "- ANSI INCITS 426-2007, T11/Project 1570-D, Fibre Channel - Security Protocols (FC-SP), February 2007, sections 7.1.7.1 and table 126." ::= { t11FcSpPoNaIpMgmtEntry 4 } t11FcSpPoNaIpMgmtWkpIndex OBJECT-TYPE SYNTAX Unsigned32 (0..4294967295) MAX-ACCESS read-create STATUS current DESCRIPTION "This object identifies the restrictions for IP management access by IP hosts in this range of IP addresses. The restrictions are specified as the set of Well-Known Protocols Access Descriptors contained in those rows of the t11FcSpPoNaWkpDescrTable for which the value of t11FcSpPoNaWkpDescrSpecifierIndx is the same as the value of this object. If there are no such rows or if the value of this object is zero, then this IP Management Entry does not identify any Well-Known Protocols Access restrictions." REFERENCE "- ANSI INCITS 426-2007, T11/Project 1570-D, Fibre Channel - Security Protocols (FC-SP), February 2007, section 7.1.7.1 and tables 127/129." ::= { t11FcSpPoNaIpMgmtEntry 5 } t11FcSpPoNaIpMgmtAttribute OBJECT-TYPE SYNTAX T11FcSpAlphaNumNameOrAbsent MAX-ACCESS read-create STATUS current DESCRIPTION "The name of a non-active Attribute Policy Object that is defined for this IP Management entry. The zero-length string indicates that no non-active Attribute Policy Object is defined for it. The effect of having no rows in the t11FcSpPoNaAttribTable for which the value of t11FcSpPoNaAttribName is the same as the value of this object, is the same as this object's value being the zero-length string." REFERENCE "- ANSI INCITS 426-2007, T11/Project 1570-D, Fibre Channel - Security Protocols (FC-SP), February 2007, section 7.1.7.1 and table 128." ::= { t11FcSpPoNaIpMgmtEntry 6 } t11FcSpPoNaIpMgmtRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "The status of this row. Values of object instances within the row can be modified at any time." ::= { t11FcSpPoNaIpMgmtEntry 7 } -- -- Non-Active Well-Known Protocol Access Descriptors -- t11FcSpPoNaWkpDescrTable OBJECT-TYPE SYNTAX SEQUENCE OF T11FcSpPoNaWkpDescrEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table of the Well-Known Protocol Access Descriptors referenced from non-active Policy Objects. A Well-Known Protocol Access Specifier is a list of Well-Known Protocol Access Descriptors each of which specifies a protocol number, a port number, and/or various flags specifying how IP management access is restricted. A non-active Well-Known Protocol Transport Access Specifier is represented by all rows of this table that have the same values of fcmInstanceIndex, t11FcSpPoFabricIndex, and t11FcSpPoNaWkpDescrSpecifierIndx." ::= { t11FcSpPoNonActive 8 } t11FcSpPoNaWkpDescrEntry OBJECT-TYPE SYNTAX T11FcSpPoNaWkpDescrEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Each entry contains information about one Well-Known Protocol Access Descriptor of a non-active Well-Known Protocol Access Specifier used within the Fabric identified by t11FcSpPoFabricIndex and managed within the Fibre Channel management instance identified by fcmInstanceIndex. The StorageType of a row in this table is specified by the instance of t11FcSpPoStorageType that is INDEX-ed by the same values of fcmInstanceIndex and t11FcSpPoFabricIndex." INDEX { fcmInstanceIndex, t11FcSpPoFabricIndex, t11FcSpPoNaWkpDescrSpecifierIndx, t11FcSpPoNaWkpDescrIndex } ::= { t11FcSpPoNaWkpDescrTable 1 } T11FcSpPoNaWkpDescrEntry ::= SEQUENCE { t11FcSpPoNaWkpDescrSpecifierIndx Unsigned32, t11FcSpPoNaWkpDescrIndex Unsigned32, t11FcSpPoNaWkpDescrFlags BITS, t11FcSpPoNaWkpDescrWkpNumber Unsigned32, t11FcSpPoNaWkpDescrDestPort InetPortNumber, t11FcSpPoNaWkpDescrRowStatus RowStatus } t11FcSpPoNaWkpDescrSpecifierIndx OBJECT-TYPE SYNTAX Unsigned32 (1..4294967295) MAX-ACCESS not-accessible STATUS current DESCRIPTION "An index value that uniquely identifies a particular non-active Well-Known Protocol Access Specifier within a Fabric." ::= { t11FcSpPoNaWkpDescrEntry 1 } t11FcSpPoNaWkpDescrIndex OBJECT-TYPE SYNTAX Unsigned32 (1..4294967295) MAX-ACCESS not-accessible STATUS current DESCRIPTION "An index value that uniquely identifies a particular Well-Known Protocol Access Descriptor within a non-active Well-Known Protocol Access Specifier." ::= { t11FcSpPoNaWkpDescrEntry 2 } t11FcSpPoNaWkpDescrFlags OBJECT-TYPE SYNTAX BITS { allow(0), wkpWildcard(1), destPortWildcard(2), readOnly(3) } MAX-ACCESS read-create STATUS current DESCRIPTION "The flag bits that specify how access is to be limited by this Well-Known Protocol Access Descriptor: - allow -- IP management access using this protocol/port is allowed if this bit is set, and to be denied if this bit is not set. - wkpWildcard -- if this bit is set, the IP Protocol number of the Well-Known Protocol to be allowed/denied is specified by the value of t11FcSpPoNaWkpDescrWkpNumber. - destPortWildcard -- if this bit is set, the Destination (TCP/UDP) Port number of the Well-Known Protocol to be allowed/denied is specified by the value of t11FcSpPoNaWkpDescrDestPort. - readOnly -- if this bit is set, then access is to be granted only for reading." REFERENCE "- ANSI INCITS 426-2007, T11/Project 1570-D, Fibre Channel - Security Protocols (FC-SP), February 2007, section 7.1.7.1 and table 131." ::= { t11FcSpPoNaWkpDescrEntry 3 } t11FcSpPoNaWkpDescrWkpNumber OBJECT-TYPE SYNTAX Unsigned32 (0..255) MAX-ACCESS read-create STATUS current DESCRIPTION "When the 'wkpWildcard' bit is set in the corresponding instance of t11FcSpPoNaWkpDescrFlags, this object specifies the IP protocol number of the Well-Known Protocol." REFERENCE "- ANSI INCITS 426-2007, T11/Project 1570-D, Fibre Channel - Security Protocols (FC-SP), February 2007, section 7.1.7.1 and table 131. - http://www.iana.org/assignments/protocol-numbers." ::= { t11FcSpPoNaWkpDescrEntry 4 } t11FcSpPoNaWkpDescrDestPort OBJECT-TYPE SYNTAX InetPortNumber MAX-ACCESS read-create STATUS current DESCRIPTION "When the 'destPortWildcard' bit is set in the corresponding instance of t11FcSpPoNaWkpDescrFlags, this object specifies the Destination (TCP/UDP) Port number of the Well-Known Protocol. When the 'destPortWildcard' bit is reset, this object is ignored (and can have the value zero)." REFERENCE "- ANSI INCITS 426-2007, T11/Project 1570-D, Fibre Channel - Security Protocols (FC-SP), February 2007, section 7.1.7.1 and table 131. - http://www.iana.org/assignments/port-numbers." ::= { t11FcSpPoNaWkpDescrEntry 5 } t11FcSpPoNaWkpDescrRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "The status of this row. Values of object instances within the row can be modified at any time." ::= { t11FcSpPoNaWkpDescrEntry 6 } -- -- Attribute Entries in Non-Active Attribute Policy Objects -- t11FcSpPoNaAttribTable OBJECT-TYPE SYNTAX SEQUENCE OF T11FcSpPoNaAttribEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table of the Attribute Policy Objects being used within non-active Policy Objects. A non-active Attribute Policy Object is represented by all the Attribute Entries in this table that have the same value of t11FcSpPoNaAttribName." ::= { t11FcSpPoNonActive 9 } t11FcSpPoNaAttribEntry OBJECT-TYPE SYNTAX T11FcSpPoNaAttribEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Each entry contains information about one Attribute Entry contained within an Attribute Policy Object that is non-active within the Fabric identified by t11FcSpPoFabricIndex and managed within the Fibre Channel management instance identified by fcmInstanceIndex. For some types of Attribute Policy Objects, it is valuable to break out some semantically significant parts of the Policy Object's value into their own individual MIB objects; for example, to extract the one or more individual Authentication Protocol Identifiers and associated Authentication Protocol Parameters out of an Attribute containing a 'AUTH_Negotiate Message Payload'. For such types, another MIB table is defined to hold the extracted values in MIB objects specific to the Attribute Policy Object's type. In such cases, the t11FcSpPoNaAttribExtension object in this table points to the other MIB table. If the value of one Attribute Entry is too large (more than 256 bytes) to be contained within the value of one instance of t11FcSpPoNaAttribValue, then one row in this table contains the first 256 bytes, and one (or more) other row(s) in this table contain the rest of the value. The StorageType of a row in this table is specified by the instance of t11FcSpPoStorageType that is INDEX-ed by the same values of fcmInstanceIndex and t11FcSpPoFabricIndex." INDEX { fcmInstanceIndex, t11FcSpPoFabricIndex, t11FcSpPoNaAttribName, t11FcSpPoNaAttribEntryIndex, t11FcSpPoNaAttribPartIndex } ::= { t11FcSpPoNaAttribTable 1 } T11FcSpPoNaAttribEntry ::= SEQUENCE { t11FcSpPoNaAttribName T11FcSpAlphaNumName, t11FcSpPoNaAttribEntryIndex Unsigned32, t11FcSpPoNaAttribPartIndex Unsigned32, t11FcSpPoNaAttribType Unsigned32, t11FcSpPoNaAttribValue OCTET STRING, t11FcSpPoNaAttribExtension OBJECT IDENTIFIER, t11FcSpPoNaAttribRowStatus RowStatus } t11FcSpPoNaAttribName OBJECT-TYPE SYNTAX T11FcSpAlphaNumName MAX-ACCESS not-accessible STATUS current DESCRIPTION "The name of the Attribute Policy Object containing one or more Attribute Entries." REFERENCE "- ANSI INCITS 426-2007, T11/Project 1570-D, Fibre Channel - Security Protocols (FC-SP), February 2007, section 7.1.8.1 and table 133." ::= { t11FcSpPoNaAttribEntry 1 } t11FcSpPoNaAttribEntryIndex OBJECT-TYPE SYNTAX Unsigned32 (1..4294967295) MAX-ACCESS not-accessible STATUS current DESCRIPTION "A unique value to distinguish this Attribute Entry from other Attribute Entries contained in the same Attribute Policy Object." REFERENCE "- ANSI INCITS 426-2007, T11/Project 1570-D, Fibre Channel - Security Protocols (FC-SP), February 2007, section 7.1.8.1, tables 133/134." ::= { t11FcSpPoNaAttribEntry 2 } t11FcSpPoNaAttribPartIndex OBJECT-TYPE SYNTAX Unsigned32 (1..4294967295) MAX-ACCESS not-accessible STATUS current DESCRIPTION "When the value of an Attribute Entry is shorter than 257 bytes, the whole value is contained in one instance of t11FcSpPoNaAttribValue, and the value of this object is 1. If the value of an Attribute Entry is longer than 256 bytes, then that value is divided up on 256-byte boundaries such that all parts are 256 bytes long except the last part which is shorter if necessary, with each such part contained in a separate row of this table, and the value of this object is set to the part number. That is, this object has the value of 1 for bytes 0-255, the value of 2 for bytes 256-511, etc." REFERENCE "- ANSI INCITS 426-2007, T11/Project 1570-D, Fibre Channel - Security Protocols (FC-SP), February 2007, section 7.1.8.1, tables 134/135." ::= { t11FcSpPoNaAttribEntry 3 } t11FcSpPoNaAttribType OBJECT-TYPE SYNTAX Unsigned32 (1..4294967295) MAX-ACCESS read-create STATUS current DESCRIPTION "The type of attribute. The first type to be defined is: t11FcSpPoNaAttribType t11FcSpPoNaAttribValue ===================== ====================== '00000001'h The AUTH_Negotiate Message Payload " REFERENCE "- ANSI INCITS 426-2007, T11/Project 1570-D, Fibre Channel - Security Protocols (FC-SP), February 2007, section 7.1.8.1, tables 134/135 and table 10." ::= { t11FcSpPoNaAttribEntry 4 } t11FcSpPoNaAttribValue OBJECT-TYPE SYNTAX OCTET STRING (SIZE (0..256)) MAX-ACCESS read-create STATUS current DESCRIPTION "The value of an Attribute Entry is divided up on 256-byte boundaries such that all parts are 256 bytes long except the last part, which is shorter if necessary, and each such part is contained in a separate instance of this object. When the value of the corresponding instance of t11FcSpPoNaAttribExtension is not zeroDotZero, then the same underlying management data has its value contained both in this object and in the individual/broken-out parts pointed to by t11FcSpPoNaAttribExtension. Thus, after any modification of the underlying management data, e.g., after a Set operation to the value of either MIB representation, then that modification is reflected in the values of both MIB representations." REFERENCE "- ANSI INCITS 426-2007, T11/Project 1570-D, Fibre Channel - Security Protocols (FC-SP), February 2007, section 7.1.8.1, tables 134/135 and table 10." ::= { t11FcSpPoNaAttribEntry 5 } t11FcSpPoNaAttribExtension OBJECT-TYPE SYNTAX OBJECT IDENTIFIER MAX-ACCESS read-only STATUS current DESCRIPTION "For some types of Attribute Policy Object, the value of this MIB object points to type-specific MIB objects that contain individual/broken-out parts of the Attribute Policy Object's value. If this object doesn't point to such type-specific MIB objects, then it contains the value: zeroDotZero. In particular, when the value of t11FcSpPoNaAttribType indicates 'AUTH_Negotiate Message Payload', one or more Authentication Protocol Identifiers and their associated Authentication Protocol Parameters are embedded within the value of the corresponding instance of t11FcSpPoNaAttribValue; MIB objects to contain these individual values are defined in the t11FcSpPoAuthProtTable. Thus, for an 'AUTH_Negotiate Message Payload' Attribute, the value of this object would contain the OID of t11FcSpPoNaAuthProtTable. When the value of this object is not zeroDotZero, then the same underlying management data has its value contained in both the individual/broken-out parts pointed to by this object and in the corresponding instance of t11FcSpPoNaAttribValue. Thus, after any modification of the underlying management data, e.g., after a Set operation to the value of either MIB representation, then that modification is reflected in the values of both MIB representations." ::= { t11FcSpPoNaAttribEntry 6 } t11FcSpPoNaAttribRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "The status of this row. Values of object instances within the row can be modified at any time." ::= { t11FcSpPoNaAttribEntry 7 } -- -- Auth. Protocol Parameters in Non-Active Attribute Policy Objects -- t11FcSpPoNaAuthProtTable OBJECT-TYPE SYNTAX SEQUENCE OF T11FcSpPoNaAuthProtEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table of Authentication Protocol Identifier and Authentication Protocol Parameters that are embedded in Attribute Policy Objects being used within non-active Policy Objects. This table is used for Attribute Entries of Attribute Policy Objects for which the value of t11FcSpPoNaAttribType indicates 'AUTH_Negotiate Message Payload' and the value of t11FcSpPoNaAttribExtension contains the OID of this table." REFERENCE "- ANSI INCITS 426-2007, T11/Project 1570-D, Fibre Channel - Security Protocols (FC-SP), February 2007, sections 5.3.2 & 7.1.8.1, tables 134/135 and tables 10/11." ::= { t11FcSpPoNonActive 10 } t11FcSpPoNaAuthProtEntry OBJECT-TYPE SYNTAX T11FcSpPoNaAuthProtEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Each row contains information about an Authentication Protocol that is extracted out of the Attribute Entry (identified by t11FcSpPoNaAttribEntryIndex) of the non-active Policy Attribute Object (identified by t11FcSpPoNaAttribName) for the Fabric identified by t11FcSpPoFabricIndex and managed within the Fibre Channel management instance identified by fcmInstanceIndex. If the value of one Attribute Protocol Parameters string is too large (more than 256 bytes) to be contained within the value of one instance of t11FcSpPoNaAuthProtParams, then one row in this table contains the first 256 bytes, and one (or more) other row(s) in this table contain the rest of the value. The same underlying management data that is represented in rows of this table is also represented by the corresponding instances of t11FcSpPoNaAttribValue. Thus, after any modification of the underlying management data, e.g., after a Set operation to the value of either MIB representation, then that modification is reflected in the values of both MIB representations." INDEX { fcmInstanceIndex, t11FcSpPoFabricIndex, t11FcSpPoNaAttribName, t11FcSpPoNaAttribEntryIndex, t11FcSpPoNaAuthProtIdentifier, t11FcSpPoNaAuthProtPartIndex } ::= { t11FcSpPoNaAuthProtTable 1 } T11FcSpPoNaAuthProtEntry ::= SEQUENCE { t11FcSpPoNaAuthProtIdentifier Unsigned32, t11FcSpPoNaAuthProtPartIndex Unsigned32, t11FcSpPoNaAuthProtParams OCTET STRING, t11FcSpPoNaAuthProtRowStatus RowStatus } t11FcSpPoNaAuthProtIdentifier OBJECT-TYPE SYNTAX Unsigned32 (0..4294967295) MAX-ACCESS not-accessible STATUS current DESCRIPTION "The Authentication Protocol Identifier: 1 = DH-CHAP 3 = FCPAP 4 = IKEv2 5 = IKEv2-AUTH 240 thru 255 = Vendor Specific Protocols all other values are 'Reserved' (by T11)." REFERENCE "- ANSI INCITS 426-2007, T11/Project 1570-D, Fibre Channel - Security Protocols (FC-SP), February 2007, section 5.3.2, table 11." ::= { t11FcSpPoNaAuthProtEntry 1 } t11FcSpPoNaAuthProtPartIndex OBJECT-TYPE SYNTAX Unsigned32 (1..4294967295) MAX-ACCESS not-accessible STATUS current DESCRIPTION "When the value of an Attribute Protocol Parameters string is shorter than 257 bytes, the whole value is contained in one instance of t11FcSpPoNaAuthProtParams, and the value of this object is 1. (This includes the case when the Attribute Protocol Parameters string is zero bytes in length.) If the value of an Authentication Protocol Parameters string is longer than 256 bytes, then that value is divided up on 256-byte boundaries such that all parts are 256 bytes long except the last part, which is shorter if necessary, with each such part contained in a separate row of this table, and the value of this object is set to the part number. That is, this object has the value of 1 for bytes 0-255, the value of 2 for bytes 256-511, etc." REFERENCE "- ANSI INCITS 426-2007, T11/Project 1570-D, Fibre Channel - Security Protocols (FC-SP), February 2007, section 5.3.2, table 10." ::= { t11FcSpPoNaAuthProtEntry 2 } t11FcSpPoNaAuthProtParams OBJECT-TYPE SYNTAX OCTET STRING (SIZE (0..256)) MAX-ACCESS read-create STATUS current DESCRIPTION "The value of an Authentication Protocol Parameters string is divided up on 256-byte boundaries such that all parts are 256 bytes long except the last part, which is shorter if necessary, and each such part is contained in a separate instance of this object." REFERENCE "- ANSI INCITS 426-2007, T11/Project 1570-D, Fibre Channel - Security Protocols (FC-SP), February 2007, section 5.3.2, table 10." ::= { t11FcSpPoNaAuthProtEntry 3 } t11FcSpPoNaAuthProtRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "The status of this row. Values of object instances within the row can be modified at any time." ::= { t11FcSpPoNaAuthProtEntry 4 } -- -- Part 4 - Statistics -- t11FcSpPoStatsTable OBJECT-TYPE SYNTAX SEQUENCE OF T11FcSpPoStatsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table of statistics maintained by FC-SP Security Policy Servers." ::= { t11FcSpPoStatistics 1 } t11FcSpPoStatsEntry OBJECT-TYPE SYNTAX T11FcSpPoStatsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A set of statistics for the FC-SP Security Policy Server on the Fabric identified by the value of t11FcSpPoFabricIndex, and managed within the Fibre Channel management instance identified by fcmInstanceIndex." INDEX { fcmInstanceIndex, t11FcSpPoFabricIndex } ::= { t11FcSpPoStatsTable 1 } T11FcSpPoStatsEntry ::= SEQUENCE { t11FcSpPoInRequests Counter32, t11FcSpPoInAccepts Counter32, t11FcSpPoInRejects Counter32 } t11FcSpPoInRequests OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of FC-SP Policy Management Requests (e.g., GPS, APS, etc.) received by this FC-SP Security Policy Server on this Fabric. This counter has no discontinuities other than those that all Counter32's have when sysUpTime=0." REFERENCE "- ANSI INCITS 426-2007, T11/Project 1570-D, Fibre Channel - Security Protocols (FC-SP), February 2007, section 7.3." ::= { t11FcSpPoStatsEntry 1 } t11FcSpPoInAccepts OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of times that this FC-SP Security Policy Server sent an Accept CT_IU on this Fabric in response to a received FC-SP Policy Management Request (e.g., GPS, APS, etc.). This counter has no discontinuities other than those that all Counter32's have when sysUpTime=0." REFERENCE "- ANSI INCITS 426-2007, T11/Project 1570-D, Fibre Channel - Security Protocols (FC-SP), February 2007, section 7.3." ::= { t11FcSpPoStatsEntry 2 } t11FcSpPoInRejects OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of times that this FC-SP Security Policy Server sent a Reject CT_IU on this Fabric in response to a received FC-SP Policy Management Request (e.g., GPS, APS, etc.). This counter has no discontinuities other than those that all Counter32's have when sysUpTime=0." REFERENCE "- ANSI INCITS 426-2007, T11/Project 1570-D, Fibre Channel - Security Protocols (FC-SP), February 2007, section 7.3." ::= { t11FcSpPoStatsEntry 3 } -- -- Part 5 - Control Information & Notifications -- -- -- Control Information -- t11FcSpPoServerAddress OBJECT-TYPE SYNTAX FcNameIdOrZero MAX-ACCESS accessible-for-notify STATUS current DESCRIPTION "The WWN of the FC-SP Security Policy Server that received a request that is referenced in a notification." ::= { t11FcSpPoControl 1 } t11FcSpPoControlTable OBJECT-TYPE SYNTAX SEQUENCE OF T11FcSpPoControlEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table of control information, including the memory realization of FC-SP Policy Databases, and concerning the generation of notifications due to FC-SP Policy-related events." ::= { t11FcSpPoControl 2 } t11FcSpPoControlEntry OBJECT-TYPE SYNTAX T11FcSpPoControlEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Each entry contains control information specific to FC-SP Policy and Policy-related events for the Fabric identified by the value of t11FcSpPoFabricIndex, and managed within the Fibre Channel management instance identified by fcmInstanceIndex." INDEX { fcmInstanceIndex, t11FcSpPoFabricIndex } ::= { t11FcSpPoControlTable 1 } T11FcSpPoControlEntry ::= SEQUENCE { t11FcSpPoStorageType StorageType, t11FcSpPoNotificationEnable TruthValue, t11FcSpPoLastNotifyType INTEGER, t11FcSpPoRequestSource FcNameIdOrZero, t11FcSpPoReasonCode T11NsGs4RejectReasonCode, t11FcSpPoCtCommandString OCTET STRING, t11FcSpPoReasonCodeExp Unsigned32, t11FcSpPoReasonVendorCode OCTET STRING } t11FcSpPoStorageType OBJECT-TYPE SYNTAX StorageType MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies the memory realization of FC-SP Policy Objects and related information for a particular Fabric; specifically, for: - rows created and/or modified for the particular Fabric in these tables: t11FcSpPoNaSummaryTable t11FcSpPoNaSwListTable t11FcSpPoNaSwMembTable t11FcSpPoNaNoMembTable t11FcSpPoNaCtDescrTable t11FcSpPoNaSwConnTable t11FcSpPoNaIpMgmtTable t11FcSpPoNaWkpDescrTable t11FcSpPoNaAttribTable - the activate and deactivate actions invoked through the t11FcSpPoOperActivate and t11FcSpPoOperDeActivate objects for the particular Fabric; and - modified information contained in the same row as an instance of this object. Even if an instance of this object has the value 'permanent(4)', none of the information defined in this MIB module for the given Fabric needs to be writable." ::= { t11FcSpPoControlEntry 1 } t11FcSpPoNotificationEnable OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-write STATUS current DESCRIPTION "This object specifies whether the following types of notifications: t11FcSpPoNotifyActivation, t11FcSpPoNotifyActivateFail, t11FcSpPoNotifyDeactivation and t11FcSpPoNotifyDeactivateFail should be generated for this Fabric." ::= { t11FcSpPoControlEntry 2 } t11FcSpPoLastNotifyType OBJECT-TYPE SYNTAX INTEGER { none(1), activation(2), activateFail(3), deactivation(4), deactivateFail(5) } MAX-ACCESS read-only STATUS current DESCRIPTION "An indication of which of the following types of notification is currently being/was most recently generated for the Fabric: 'activation' -- t11FcSpPoNotifyActivation 'activateFail' -- t11FcSpPoNotifyActivateFail 'deactivation' -- t11FcSpPoNotifyDeactivation 'deactivateFail' -- t11FcSpPoNotifyDeactivateFail The value 'none' indicates that none of these types of notifications have been generated since the last restart of the network management system, and therefore that the corresponding instances of: t11FcSpPoRequestSource, t11FcSpPoReasonCode, t11FcSpPoCtCommandString, t11FcSpPoReasonCodeExp, and t11FcSpPoReasonVendorCode are irrelevant." ::= { t11FcSpPoControlEntry 3 } t11FcSpPoRequestSource OBJECT-TYPE SYNTAX FcNameIdOrZero MAX-ACCESS read-only STATUS current DESCRIPTION "The WWN of the source of the (Activate Policy Summary or Deactivate Policy Summary) request for which the current/most recent notification of the type indicated by the corresponding instance of t11FcSpPoLastNotifyType is being/was generated. If no source is available, the value of this object is the zero-length string." DEFVAL { "" } ::= { t11FcSpPoControlEntry 4 } t11FcSpPoReasonCode OBJECT-TYPE SYNTAX T11NsGs4RejectReasonCode MAX-ACCESS read-only STATUS current DESCRIPTION "The reason code associated with the failure that is indicated when the value of the corresponding instance of t11FcSpPoLastNotifyType is 'activateFail' or 'deactivateFail'. For other values of t11FcSpPoLastNotifyType, the value of this object is 'none(1)'." REFERENCE "- ANSI INCITS 426-2007, T11/Project 1570-D, Fibre Channel - Security Protocols (FC-SP), February 2007, section 7.3.6.2 & 7.3.6.3" ::= { t11FcSpPoControlEntry 5 } t11FcSpPoCtCommandString OBJECT-TYPE SYNTAX OCTET STRING (SIZE (0..255)) MAX-ACCESS read-only STATUS current DESCRIPTION "The binary content of the failed request that is indicated when the value of the corresponding instance of t11FcSpPoLastNotifyType is 'activateFail' or 'deactivateFail'. The content of the request is formatted as an octet string (in network byte order) containing the CT_IU, as described in Table 2 of [FC-GS-5] (including the preamble). For other values of t11FcSpPoLastNotifyType, or if the CT_IU's content is unavailable, the value of this object is the zero-length string. When the length of this object is 255 octets, it contains the first 255 octets of the CT_IU (in network-byte order)." ::= { t11FcSpPoControlEntry 6 } t11FcSpPoReasonCodeExp OBJECT-TYPE SYNTAX Unsigned32 (0..255) MAX-ACCESS read-only STATUS current DESCRIPTION "The reason code explanation associated with the failure that is indicated when the value of the corresponding instance of t11FcSpPoLastNotifyType is 'activateFail' or 'deactivateFail'. For other values of t11FcSpPoLastNotifyType, the value of this object is zero." REFERENCE "- ANSI INCITS 426-2007, T11/Project 1570-D, Fibre Channel - Security Protocols (FC-SP), February 2007, section 7.3.6.2 & 7.3.6.3" ::= { t11FcSpPoControlEntry 7 } t11FcSpPoReasonVendorCode OBJECT-TYPE SYNTAX OCTET STRING (SIZE (0 | 1)) MAX-ACCESS read-only STATUS current DESCRIPTION "The vendor-specific reason code associated with the failure that is indicated when the value of the corresponding instance of t11FcSpPoLastNotifyType is 'activateFail' or 'deactivateFail'. For other values of t11FcSpPoLastNotifyType, or if no vendor-specific reason code is available, the value of this object is the zero-length string." REFERENCE "- ANSI INCITS 426-2007, T11/Project 1570-D, Fibre Channel - Security Protocols (FC-SP), February 2007, section 7.3.6.2 & 7.3.6.3" ::= { t11FcSpPoControlEntry 8 } -- -- Notification definitions -- t11FcSpPoNotifyActivation NOTIFICATION-TYPE OBJECTS { t11FcSpPoServerAddress, t11FcSpPoPolicySummaryObjName, t11FcSpPoRequestSource } STATUS current DESCRIPTION "This notification is generated whenever a Security Policy Server (indicated by the value of t11FcSpPoServerAddress) successfully completes the execution of an Activate Policy Summary request. The value of t11FcSpPoRequestSource indicates the source of the APS request. The value of t11FcSpPoPolicySummaryObjName indicates the name of the activated Policy Summary Object." ::= { t11FcSpPoMIBNotifications 1 } t11FcSpPoNotifyActivateFail NOTIFICATION-TYPE OBJECTS { t11FcSpPoServerAddress, t11FcSpPoRequestSource, t11FcSpPoCtCommandString, t11FcSpPoReasonCode, t11FcSpPoReasonCodeExp, t11FcSpPoReasonVendorCode } STATUS current DESCRIPTION "This notification is generated whenever a Security Policy Server (indicated by the value of t11FcSpPoServerAddress) fails to complete the execution of an Activate Policy Summary request. The value of t11FcSpPoCtCommandString indicates the rejected request, and the values of t11FcSpPoReasonCode, t11FcSpPoReasonCodeExp, and t11FcSpPoReasonVendorCode indicate the reason for the rejection. The value of t11FcSpPoRequestSource indicates the source of the request." REFERENCE "- ANSI INCITS 426-2007, T11/Project 1570-D, Fibre Channel - Security Protocols (FC-SP), February 2007, section 7.3.6.2." ::= { t11FcSpPoMIBNotifications 2 } t11FcSpPoNotifyDeactivation NOTIFICATION-TYPE OBJECTS { t11FcSpPoServerAddress, t11FcSpPoRequestSource } STATUS current DESCRIPTION "This notification is generated whenever a Security Policy Server (indicated by the value of t11FcSpPoServerAddress) successfully completes the execution of a Deactivate Policy Summary request. The value of t11FcSpPoRequestSource indicates the source of the DPS request." REFERENCE "- ANSI INCITS 426-2007, T11/Project 1570-D, Fibre Channel - Security Protocols (FC-SP), February 2007, section 7.3.6.3." ::= { t11FcSpPoMIBNotifications 3 } t11FcSpPoNotifyDeactivateFail NOTIFICATION-TYPE OBJECTS { t11FcSpPoServerAddress, t11FcSpPoRequestSource, t11FcSpPoCtCommandString, t11FcSpPoReasonCode, t11FcSpPoReasonCodeExp, t11FcSpPoReasonVendorCode } STATUS current DESCRIPTION "This notification is generated whenever a Security Policy Server (indicated by the value of t11FcSpPoServerAddress) fails to complete the execution of a Deactivate Policy Summary request. The value of t11FcSpPoCtCommandString indicates the rejected request, and the values of t11FcSpPoReasonCode, t11FcSpPoReasonCodeExp, and t11FcSpPoReasonVendorCode indicate the reason for the rejection. The value of t11FcSpPoRequestSource indicates the source of the request." ::= { t11FcSpPoMIBNotifications 4 } -- -- Conformance -- t11FcSpPoMIBCompliances OBJECT IDENTIFIER ::= { t11FcSpPoMIBConformance 1 } t11FcSpPoMIBGroups OBJECT IDENTIFIER ::= { t11FcSpPoMIBConformance 2 } t11FcSpPoMIBCompliance MODULE-COMPLIANCE STATUS current DESCRIPTION "The compliance statement for entities that support the Fabric Policies defined in FC-SP," MODULE -- this module MANDATORY-GROUPS { t11FcSpPoActiveObjectsGroup } GROUP t11FcSpPoNonActiveObjectsGroup DESCRIPTION "These objects are mandatory for FC-SP Security Policy Servers." GROUP t11FcSpPoNotifyObjectsGroup DESCRIPTION "These objects are mandatory for FC-SP Security Policy Servers." GROUP t11FcSpPoNotificationGroup DESCRIPTION "These notifications are mandatory for FC-SP Security Policy Servers." GROUP t11FcSpPoOperationsObjectsGroup DESCRIPTION "These objects are mandatory only for FC-SP Security Policy Servers that support the activation/deactivation of policies via SNMP." GROUP t11FcSpPoStatsObjectsGroup DESCRIPTION "These objects are optional." -- Write access is not required for any objects in this MIB module: OBJECT t11FcSpPoOperActivate MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT t11FcSpPoOperDeActivate MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT t11FcSpPoStorageType MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT t11FcSpPoNotificationEnable MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT t11FcSpPoNaSummaryPolicyNameType MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT t11FcSpPoNaSummaryPolicyName MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT t11FcSpPoNaSummaryHashStatus MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT t11FcSpPoNaSummaryRowStatus MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT t11FcSpPoNaSwListFabricName MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT t11FcSpPoNaSwListRowStatus MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT t11FcSpPoNaSwMembFlags MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT t11FcSpPoNaSwMembDomainID MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT t11FcSpPoNaSwMembPolicyDataRole MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT t11FcSpPoNaSwMembAuthBehaviour MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT t11FcSpPoNaSwMembAttribute MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT t11FcSpPoNaSwMembRowStatus MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT t11FcSpPoNaNoMembFlags MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT t11FcSpPoNaNoMembCtAccessIndex MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT t11FcSpPoNaNoMembAttribute MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT t11FcSpPoNaNoMembRowStatus MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT t11FcSpPoNaCtDescrFlags MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT t11FcSpPoNaCtDescrGsType MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT t11FcSpPoNaCtDescrGsSubType MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT t11FcSpPoNaCtDescrRowStatus MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT t11FcSpPoNaSwConnAllowedNameType MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT t11FcSpPoNaSwConnAllowedName MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT t11FcSpPoNaSwConnRowStatus MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT t11FcSpPoNaIpMgmtWkpIndex MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT t11FcSpPoNaIpMgmtAttribute MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT t11FcSpPoNaIpMgmtRowStatus MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT t11FcSpPoNaWkpDescrFlags MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT t11FcSpPoNaWkpDescrWkpNumber MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT t11FcSpPoNaWkpDescrDestPort MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT t11FcSpPoNaWkpDescrRowStatus MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT t11FcSpPoNaAttribType MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT t11FcSpPoNaAttribValue MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT t11FcSpPoNaAttribRowStatus MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT t11FcSpPoNaAuthProtParams MIN-ACCESS read-only DESCRIPTION "Write access is not required." OBJECT t11FcSpPoNaAuthProtRowStatus MIN-ACCESS read-only DESCRIPTION "Write access is not required." ::= { t11FcSpPoMIBCompliances 1 } -- Units of Conformance t11FcSpPoActiveObjectsGroup OBJECT-GROUP OBJECTS { t11FcSpPoPolicySummaryObjName, t11FcSpPoAdminFabricName, t11FcSpPoActivatedTimeStamp, t11FcSpPoSummaryPolicyType, t11FcSpPoSummaryHashFormat, t11FcSpPoSummaryHashValue, t11FcSpPoSwMembSwitchFlags, t11FcSpPoSwMembDomainID, t11FcSpPoSwMembPolicyDataRole, t11FcSpPoSwMembAuthBehaviour, t11FcSpPoSwMembAttribute, t11FcSpPoNoMembFlags, t11FcSpPoNoMembCtAccessIndex, t11FcSpPoNoMembAttribute, t11FcSpPoCtDescrFlags, t11FcSpPoCtDescrGsType, t11FcSpPoCtDescrGsSubType, t11FcSpPoSwConnAllowedNameType, t11FcSpPoSwConnAllowedName, t11FcSpPoIpMgmtWkpIndex, t11FcSpPoIpMgmtAttribute, t11FcSpPoWkpDescrFlags, t11FcSpPoWkpDescrWkpNumber, t11FcSpPoWkpDescrDestPort, t11FcSpPoAttribType, t11FcSpPoAttribValue, t11FcSpPoAttribExtension, t11FcSpPoAuthProtParams } STATUS current DESCRIPTION "A collection of MIB objects that contain information about active Policy Objects that express Fibre Channel Security (FC-SP) policy." ::= { t11FcSpPoMIBGroups 1 } t11FcSpPoOperationsObjectsGroup OBJECT-GROUP OBJECTS { t11FcSpPoOperActivate, t11FcSpPoOperDeActivate, t11FcSpPoOperResult, t11FcSpPoOperFailCause } STATUS current DESCRIPTION "A collection of MIB objects that allow a new set of Fibre Channel Security (FC-SP) policies to be activated or an existing set to be deactivated." ::= { t11FcSpPoMIBGroups 2 } t11FcSpPoNonActiveObjectsGroup OBJECT-GROUP OBJECTS { t11FcSpPoStorageType, t11FcSpPoNaSummaryPolicyNameType, t11FcSpPoNaSummaryPolicyName, t11FcSpPoNaSummaryHashStatus, t11FcSpPoNaSummaryHashFormat, t11FcSpPoNaSummaryHashValue, t11FcSpPoNaSummaryRowStatus, t11FcSpPoNaSwListFabricName, t11FcSpPoNaSwListRowStatus, t11FcSpPoNaSwMembFlags, t11FcSpPoNaSwMembDomainID, t11FcSpPoNaSwMembPolicyDataRole, t11FcSpPoNaSwMembAuthBehaviour, t11FcSpPoNaSwMembAttribute, t11FcSpPoNaSwMembRowStatus, t11FcSpPoNaNoMembFlags, t11FcSpPoNaNoMembCtAccessIndex, t11FcSpPoNaNoMembAttribute, t11FcSpPoNaNoMembRowStatus, t11FcSpPoNaCtDescrFlags, t11FcSpPoNaCtDescrGsType, t11FcSpPoNaCtDescrGsSubType, t11FcSpPoNaCtDescrRowStatus, t11FcSpPoNaSwConnAllowedNameType, t11FcSpPoNaSwConnAllowedName, t11FcSpPoNaSwConnRowStatus, t11FcSpPoNaIpMgmtWkpIndex, t11FcSpPoNaIpMgmtAttribute, t11FcSpPoNaIpMgmtRowStatus, t11FcSpPoNaWkpDescrFlags, t11FcSpPoNaWkpDescrWkpNumber, t11FcSpPoNaWkpDescrDestPort, t11FcSpPoNaWkpDescrRowStatus, t11FcSpPoNaAttribType, t11FcSpPoNaAttribValue, t11FcSpPoNaAttribExtension, t11FcSpPoNaAttribRowStatus, t11FcSpPoNaAuthProtParams, t11FcSpPoNaAuthProtRowStatus } STATUS current DESCRIPTION "A collection of MIB objects that contain information about non-active Policy Objects available for activation in order to change Fibre Channel Security (FC-SP) policy." ::= { t11FcSpPoMIBGroups 3 } t11FcSpPoStatsObjectsGroup OBJECT-GROUP OBJECTS { t11FcSpPoInRequests, t11FcSpPoInAccepts, t11FcSpPoInRejects } STATUS current DESCRIPTION "A collection of MIB objects that contain statistics that can be maintained by FC-SP Security Policy Servers." ::= { t11FcSpPoMIBGroups 4 } t11FcSpPoNotifyObjectsGroup OBJECT-GROUP OBJECTS { t11FcSpPoNotificationEnable, t11FcSpPoServerAddress, t11FcSpPoLastNotifyType, t11FcSpPoRequestSource, t11FcSpPoReasonCode, t11FcSpPoCtCommandString, t11FcSpPoReasonCodeExp, t11FcSpPoReasonVendorCode } STATUS current DESCRIPTION "A collection of MIB objects to control the generation of notifications concerning Fibre Channel Security (FC-SP) policy, and to hold information contained in such notifications." ::= { t11FcSpPoMIBGroups 5 } t11FcSpPoNotificationGroup NOTIFICATION-GROUP NOTIFICATIONS { t11FcSpPoNotifyActivation, t11FcSpPoNotifyActivateFail, t11FcSpPoNotifyDeactivation, t11FcSpPoNotifyDeactivateFail } STATUS current DESCRIPTION "A collection of notifications of events concerning Fibre Channel Security (FC-SP) policy." ::= { t11FcSpPoMIBGroups 6 } END