-- ***************************************************************** -- REDSTONE-L2TP-MIB -- -- Redstone Communications Inc. Enterprise MIB -- Layer Two Tunneling Protocol (L2TP) MIB -- -- Copyright 2000 Redstone Communications, Incorporated. -- All Rights Reserved. -- ***************************************************************** REDSTONE-L2TP-MIB DEFINITIONS ::= BEGIN IMPORTS MODULE-IDENTITY, OBJECT-TYPE, Integer32, Counter32, Gauge32, Unsigned32, IpAddress FROM SNMPv2-SMI TEXTUAL-CONVENTION, DisplayString, RowStatus, TruthValue FROM SNMPv2-TC OBJECT-GROUP, MODULE-COMPLIANCE FROM SNMPv2-CONF InterfaceIndex, InterfaceIndexOrZero FROM IF-MIB rsMgmt FROM REDSTONE-SMI RsEnable FROM REDSTONE-TC; rsL2tpMIB MODULE-IDENTITY LAST-UPDATED "9901100000Z" ORGANIZATION "Redstone Communications, Inc." CONTACT-INFO " Redstone Communications, Inc. 5 Carlisle Road Westford MA 01886 USA Tel: +1-978-692-1999 Email: mib@redstonecom.com " DESCRIPTION "The L2TP MIB for the Redstone Communications Inc. enterprise." REVISION "9901100000Z" DESCRIPTION "Initial revision, based in part on IETF L2TP Working Group draft-ietf-l2tpext-l2tp-mib-05." ::= { rsMgmt 35 } -- ++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++ -- Textual conventions -- ++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++ RsL2tpTunnelId ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "An L2TP Tunnel ID. Implementation constraints may restrict the range of values actually used." SYNTAX Integer32(0..65535) RsL2tpSessionId ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "An L2TP Session ID. Implementation constraints may restrict the range of values actually used." SYNTAX Integer32(0..65535) RsL2tpAdminState ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "The administrative state exerted on L2TP tunnels sessions at some scope of control. enabled New tunnels/sessions may be instantiated. disabled All tunnels/sessions are terminated. drain No new tunnels/sessions may be instantiated, but any existing tunnels/sessions may persist until they expire by other means. The DESCRIPTION clause of an object defined to have this syntax must describe the scope of control that object exerts (e.g., all tunnels/sessions across the system, sessions within a single tunnel, etc.)." SYNTAX INTEGER { enabled(0), disabled(1), drain(2) } RsL2tpTransport ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "Transport type over which L2TP is carried." SYNTAX INTEGER { other(0), udpIp(1) } -- ++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++ -- Managed object groups -- ++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++ rsL2tpTraps OBJECT IDENTIFIER ::= { rsL2tpMIB 0 } rsL2tpObjects OBJECT IDENTIFIER ::= { rsL2tpMIB 1 } rsL2tpTrapControl OBJECT IDENTIFIER ::= { rsL2tpMIB 2 } rsL2tpConformance OBJECT IDENTIFIER ::= { rsL2tpMIB 3 } -- -- Major subtrees -- rsL2tpSystem OBJECT IDENTIFIER ::= { rsL2tpObjects 1 } rsL2tpDestination OBJECT IDENTIFIER ::= { rsL2tpObjects 2 } rsL2tpTunnel OBJECT IDENTIFIER ::= { rsL2tpObjects 3 } rsL2tpSession OBJECT IDENTIFIER ::= { rsL2tpObjects 4 } rsL2tpTransport OBJECT IDENTIFIER ::= { rsL2tpObjects 5 } -- ...................................................................... -- L2TP System Group -- ...................................................................... rsL2tpSystemConfig OBJECT IDENTIFIER ::= { rsL2tpSystem 1 } rsL2tpSystemStatus OBJECT IDENTIFIER ::= { rsL2tpSystem 2 } -- -- L2TP System-level Configuration -- rsL2tpSysConfigAdminState OBJECT-TYPE SYNTAX RsL2tpAdminState MAX-ACCESS read-write STATUS current DESCRIPTION "Exerts control over all L2TP tunnels/sessions in the system." ::= { rsL2tpSystemConfig 1 } rsL2tpSysConfigDestructTimeout OBJECT-TYPE SYNTAX Integer32(0..3600) UNITS "seconds" MAX-ACCESS read-write STATUS current DESCRIPTION "The amount of time, in seconds, to preserve dynamic tunnels/sessions after they become inactive, e.g. to poll their statistics." ::= { rsL2tpSystemConfig 2 } rsL2tpSysConfigIpChecksumEnable OBJECT-TYPE SYNTAX RsEnable MAX-ACCESS read-write STATUS current DESCRIPTION "Enable/disable IP checksumming for tunnels with UDP/IP transport." ::= { rsL2tpSystemConfig 3 } -- -- L2TP System-level Status and Statistics -- rsL2tpSysStatusProtocolVersion OBJECT-TYPE SYNTAX OCTET STRING (SIZE(2..256)) MAX-ACCESS read-only STATUS current DESCRIPTION "Vector of supported L2TP protocol version and revision numbers. Supported versions are identified via a two octet pairing where the first octet indicates the version and the second octet contains the revision." ::= { rsL2tpSystemStatus 1 } rsL2tpSysStatusVendorName OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "Vendor name of the L2TP protocol stack." ::= { rsL2tpSystemStatus 2 } rsL2tpSysStatusFirmwareRev OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "Firmware revision for the L2TP protocol stack." ::= { rsL2tpSystemStatus 3 } rsL2tpSysStatusTotalDestinations OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of destination creations attempted." ::= { rsL2tpSystemStatus 4 } rsL2tpSysStatusFailedDestinations OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of destination creation attempts that failed." ::= { rsL2tpSystemStatus 5 } rsL2tpSysStatusActiveDestinations OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of destinations having at least one active tunnel." ::= { rsL2tpSystemStatus 6 } rsL2tpSysStatusTotalTunnels OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of tunnel creations attempted." ::= { rsL2tpSystemStatus 7 } rsL2tpSysStatusFailedTunnels OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of tunnel creation attempts that failed to reach the established state." ::= { rsL2tpSystemStatus 8 } rsL2tpSysStatusFailedTunnelAuthens OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of tunnel creation attempts that failed authentication." ::= { rsL2tpSystemStatus 9 } rsL2tpSysStatusActiveTunnels OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of tunnels currently established." ::= { rsL2tpSystemStatus 10 } rsL2tpSysStatusTotalSessions OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of session creations attempted." ::= { rsL2tpSystemStatus 11 } rsL2tpSysStatusFailedSessions OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of session creation attempts that failed to reach the established state." ::= { rsL2tpSystemStatus 12 } rsL2tpSysStatusActiveSessions OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of sessions currently established." ::= { rsL2tpSystemStatus 13 } -- ...................................................................... -- L2TP Destination Group -- ...................................................................... rsL2tpDestConfig OBJECT IDENTIFIER ::= { rsL2tpDestination 1 } rsL2tpDestStatus OBJECT IDENTIFIER ::= { rsL2tpDestination 2 } rsL2tpDestStatistics OBJECT IDENTIFIER ::= { rsL2tpDestination 3 } -- -- Destination-level Configuration -- -- { rsL2tpDestConfig 1 } reserved for "next ifIndex" acquisition rsL2tpDestConfigTable OBJECT-TYPE SYNTAX SEQUENCE OF RsL2tpDestConfigEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The L2TP destination configuration table. Each entry in this table has a corresponding entry in the Interfaces MIB ifTable, and in rsL2tpDestStatsTable." ::= { rsL2tpDestConfig 2 } rsL2tpDestConfigEntry OBJECT-TYPE SYNTAX RsL2tpDestConfigEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Describes the configuration attributes of an L2TP destination." INDEX { rsL2tpDestConfigIfIndex } ::= { rsL2tpDestConfigTable 1 } RsL2tpDestConfigEntry ::= SEQUENCE { rsL2tpDestConfigIfIndex InterfaceIndex, rsL2tpDestConfigRowStatus RowStatus, rsL2tpDestConfigAdminState RsL2tpAdminState } rsL2tpDestConfigIfIndex OBJECT-TYPE SYNTAX InterfaceIndex MAX-ACCESS not-accessible STATUS current DESCRIPTION "Same value as ifIndex for the corresponding entry in Interfaces MIB ifTable." ::= { rsL2tpDestConfigEntry 1 } rsL2tpDestConfigRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "An implementation may choose not to support administrative configuration of tunnels." ::= { rsL2tpDestConfigEntry 2 } rsL2tpDestConfigAdminState OBJECT-TYPE SYNTAX RsL2tpAdminState MAX-ACCESS read-create STATUS current DESCRIPTION "The configured administrative state." DEFVAL { enabled } ::= { rsL2tpDestConfigEntry 3 } -- -- Destination-level Status -- rsL2tpDestStatusTable OBJECT-TYPE SYNTAX SEQUENCE OF RsL2tpDestStatusEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The L2TP destination status table. Each entry in this table has a corresponding entry in the Interfaces MIB ifTable, and in rsL2tpDestConfigTable." ::= { rsL2tpDestStatus 1 } rsL2tpDestStatusEntry OBJECT-TYPE SYNTAX RsL2tpDestStatusEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Describes the status attributes of an L2TP destination." INDEX { rsL2tpDestStatusIfIndex } ::= { rsL2tpDestStatusTable 1 } RsL2tpDestStatusEntry ::= SEQUENCE { rsL2tpDestStatusIfIndex InterfaceIndex, rsL2tpDestStatusTransport RsL2tpTransport, rsL2tpDestStatusEffectiveAdminState RsL2tpAdminState, rsL2tpDestStatusTotalTunnels Counter32, rsL2tpDestStatusFailedTunnels Counter32, rsL2tpDestStatusFailedTunnelAuthens Counter32, rsL2tpDestStatusActiveTunnels Gauge32, rsL2tpDestStatusTotalSessions Counter32, rsL2tpDestStatusFailedSessions Counter32, rsL2tpDestStatusActiveSessions Gauge32 } rsL2tpDestStatusIfIndex OBJECT-TYPE SYNTAX InterfaceIndex MAX-ACCESS not-accessible STATUS current DESCRIPTION "Same value as ifIndex for the corresponding entry in Interfaces MIB ifTable." ::= { rsL2tpDestStatusEntry 1 } rsL2tpDestStatusTransport OBJECT-TYPE SYNTAX RsL2tpTransport MAX-ACCESS read-only STATUS current DESCRIPTION "The underlying transport over which this L2TP destination is carried." ::= { rsL2tpDestStatusEntry 2 } rsL2tpDestStatusEffectiveAdminState OBJECT-TYPE SYNTAX RsL2tpAdminState MAX-ACCESS read-only STATUS current DESCRIPTION "The administrative state currently in effect. This could be the configured admin state for this destination, or an overriding admin state exerted from a higher hierarchical level (system)." ::= { rsL2tpDestStatusEntry 3 } rsL2tpDestStatusTotalTunnels OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of tunnel creations attempted." ::= { rsL2tpDestStatusEntry 4 } rsL2tpDestStatusFailedTunnels OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of tunnel creation attempts that failed to reach the established state." ::= { rsL2tpDestStatusEntry 5 } rsL2tpDestStatusFailedTunnelAuthens OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of tunnel creation attempts that failed authentication." ::= { rsL2tpDestStatusEntry 6 } rsL2tpDestStatusActiveTunnels OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of tunnels currently established." ::= { rsL2tpDestStatusEntry 7 } rsL2tpDestStatusTotalSessions OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of session creations attempted." ::= { rsL2tpDestStatusEntry 8 } rsL2tpDestStatusFailedSessions OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of session creation attempts that failed to reach the established state." ::= { rsL2tpDestStatusEntry 9 } rsL2tpDestStatusActiveSessions OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of sessions currently established." ::= { rsL2tpDestStatusEntry 10 } -- -- Destination-level Statistics -- rsL2tpDestStatTable OBJECT-TYPE SYNTAX SEQUENCE OF RsL2tpDestStatEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The L2TP destination statistics table. Describes the aggregate control and payload statistics for all L2TP tunnels configured on each destination. Each entry in this table has a corresponding entry in the Interfaces MIB ifTable, and in rsL2tpDestConfigTable." ::= { rsL2tpDestStatistics 1 } rsL2tpDestStatEntry OBJECT-TYPE SYNTAX RsL2tpDestStatEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Describes the aggregate L2TP control and payload statistics for all L2TP tunnels on an L2TP destination." INDEX { rsL2tpDestStatIfIndex } ::= { rsL2tpDestStatTable 1 } RsL2tpDestStatEntry ::= SEQUENCE { rsL2tpDestStatIfIndex InterfaceIndex, rsL2tpDestStatCtlRecvOctets Counter32, rsL2tpDestStatCtlRecvPackets Counter32, rsL2tpDestStatCtlRecvErrors Counter32, rsL2tpDestStatCtlRecvDiscards Counter32, rsL2tpDestStatCtlSendOctets Counter32, rsL2tpDestStatCtlSendPackets Counter32, rsL2tpDestStatCtlSendErrors Counter32, rsL2tpDestStatCtlSendDiscards Counter32, rsL2tpDestStatPayRecvOctets Counter32, rsL2tpDestStatPayRecvPackets Counter32, rsL2tpDestStatPayRecvErrors Counter32, rsL2tpDestStatPayRecvDiscards Counter32, rsL2tpDestStatPaySendOctets Counter32, rsL2tpDestStatPaySendPackets Counter32, rsL2tpDestStatPaySendErrors Counter32, rsL2tpDestStatPaySendDiscards Counter32 } rsL2tpDestStatIfIndex OBJECT-TYPE SYNTAX InterfaceIndex MAX-ACCESS not-accessible STATUS current DESCRIPTION "Same value as ifIndex for the corresponding entry in Interfaces MIB ifTable." ::= { rsL2tpDestStatEntry 1 } rsL2tpDestStatCtlRecvOctets OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of control octets received." ::= { rsL2tpDestStatEntry 2 } rsL2tpDestStatCtlRecvPackets OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of control packets received." ::= { rsL2tpDestStatEntry 3 } rsL2tpDestStatCtlRecvErrors OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of control packets incurring reception errors." ::= { rsL2tpDestStatEntry 4 } rsL2tpDestStatCtlRecvDiscards OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of control packets discarded after reception." ::= { rsL2tpDestStatEntry 5 } rsL2tpDestStatCtlSendOctets OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of control octets sent." ::= { rsL2tpDestStatEntry 6 } rsL2tpDestStatCtlSendPackets OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of control packets sent." ::= { rsL2tpDestStatEntry 7 } rsL2tpDestStatCtlSendErrors OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of control packets incurring transmission errors." ::= { rsL2tpDestStatEntry 8 } rsL2tpDestStatCtlSendDiscards OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of control packets discarded before transmission." ::= { rsL2tpDestStatEntry 9 } rsL2tpDestStatPayRecvOctets OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of payload octets received." ::= { rsL2tpDestStatEntry 10 } rsL2tpDestStatPayRecvPackets OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of payload packets received." ::= { rsL2tpDestStatEntry 11 } rsL2tpDestStatPayRecvErrors OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of payload packets incurring reception errors." ::= { rsL2tpDestStatEntry 12 } rsL2tpDestStatPayRecvDiscards OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of payload packets discarded after reception." ::= { rsL2tpDestStatEntry 13 } rsL2tpDestStatPaySendOctets OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of payload octets sent." ::= { rsL2tpDestStatEntry 14 } rsL2tpDestStatPaySendPackets OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of payload packets sent." ::= { rsL2tpDestStatEntry 15 } rsL2tpDestStatPaySendErrors OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of payload packets incurring transmission errors." ::= { rsL2tpDestStatEntry 16 } rsL2tpDestStatPaySendDiscards OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of payload packets discarded before transmission." ::= { rsL2tpDestStatEntry 17 } -- ...................................................................... -- L2TP Tunnel Group -- ...................................................................... rsL2tpTunnelConfig OBJECT IDENTIFIER ::= { rsL2tpTunnel 1 } rsL2tpTunnelStatus OBJECT IDENTIFIER ::= { rsL2tpTunnel 2 } rsL2tpTunnelStatistics OBJECT IDENTIFIER ::= { rsL2tpTunnel 3 } rsL2tpTunnelMap OBJECT IDENTIFIER ::= { rsL2tpTunnel 4 } -- -- Tunnel-level Configuration -- -- { rsL2tpTunnelConfig 1 } reserved for "next ifIndex" acquisition rsL2tpTunnelConfigTable OBJECT-TYPE SYNTAX SEQUENCE OF RsL2tpTunnelConfigEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The L2TP tunnel configuration table. Each entry in this table has a corresponding entry in the Interfaces MIB ifTable, and in rsL2tpTunnelStatsTable." ::= { rsL2tpTunnelConfig 2 } rsL2tpTunnelConfigEntry OBJECT-TYPE SYNTAX RsL2tpTunnelConfigEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Describes the configuration attributes of an L2TP tunnel." INDEX { rsL2tpTunnelConfigIfIndex } ::= { rsL2tpTunnelConfigTable 1 } RsL2tpTunnelConfigEntry ::= SEQUENCE { rsL2tpTunnelConfigIfIndex InterfaceIndex, rsL2tpTunnelConfigRowStatus RowStatus, rsL2tpTunnelConfigAdminState RsL2tpAdminState } rsL2tpTunnelConfigIfIndex OBJECT-TYPE SYNTAX InterfaceIndex MAX-ACCESS not-accessible STATUS current DESCRIPTION "Same value as ifIndex for the corresponding entry in Interfaces MIB ifTable." ::= { rsL2tpTunnelConfigEntry 1 } rsL2tpTunnelConfigRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "An implementation may choose not to support administrative configuration of tunnels." ::= { rsL2tpTunnelConfigEntry 2 } rsL2tpTunnelConfigAdminState OBJECT-TYPE SYNTAX RsL2tpAdminState MAX-ACCESS read-create STATUS current DESCRIPTION "The configured administrative state." DEFVAL { enabled } ::= { rsL2tpTunnelConfigEntry 3 } -- -- Tunnel-level Status and Statistics -- rsL2tpTunnelStatusTable OBJECT-TYPE SYNTAX SEQUENCE OF RsL2tpTunnelStatusEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The L2TP tunnel status and statistics table. Each entry in this table has a corresponding entry in the Interfaces MIB ifTable, and in rsL2tpTunnelConfigTable." ::= { rsL2tpTunnelStatus 1 } rsL2tpTunnelStatusEntry OBJECT-TYPE SYNTAX RsL2tpTunnelStatusEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An L2TP tunnel interface stats entry." INDEX { rsL2tpTunnelStatusIfIndex } ::= { rsL2tpTunnelStatusTable 1 } RsL2tpTunnelStatusEntry ::= SEQUENCE { rsL2tpTunnelStatusIfIndex InterfaceIndex, rsL2tpTunnelStatusTransport RsL2tpTransport, rsL2tpTunnelStatusLocalTunnelId RsL2tpTunnelId, rsL2tpTunnelStatusRemoteTunnelId RsL2tpTunnelId, rsL2tpTunnelStatusEffectiveAdminState RsL2tpAdminState, rsL2tpTunnelStatusState INTEGER, rsL2tpTunnelStatusInitiated INTEGER, rsL2tpTunnelStatusRemoteHostName DisplayString, rsL2tpTunnelStatusRemoteVendorName DisplayString, rsL2tpTunnelStatusRemoteFirmwareRevision Integer32, rsL2tpTunnelStatusRemoteProtocolVersion OCTET STRING, rsL2tpTunnelStatusRemoteBearerCapabilities INTEGER, rsL2tpTunnelStatusRemoteFramingCapabilities INTEGER, rsL2tpTunnelStatusRecvWindowSize Gauge32, rsL2tpTunnelStatusSendWindowSize Gauge32, rsL2tpTunnelStatusSendQueueDepth Gauge32, rsL2tpTunnelStatusRecvSeq Integer32, rsL2tpTunnelStatusRecvSeqAck Integer32, rsL2tpTunnelStatusSendSeq Integer32, rsL2tpTunnelStatusSendSeqAck Integer32, rsL2tpTunnelStatusTotalSessions Counter32, rsL2tpTunnelStatusFailedSessions Counter32, rsL2tpTunnelStatusActiveSessions Gauge32, rsL2tpTunnelStatusLastResultCode Integer32, rsL2tpTunnelStatusLastErrorCode Integer32, rsL2tpTunnelStatusLastErrorMessage DisplayString } rsL2tpTunnelStatusIfIndex OBJECT-TYPE SYNTAX InterfaceIndex MAX-ACCESS not-accessible STATUS current DESCRIPTION "Same as the value of ifIndex for the corresponding entry in Interfaces MIB ifTable." ::= { rsL2tpTunnelStatusEntry 1 } rsL2tpTunnelStatusTransport OBJECT-TYPE SYNTAX RsL2tpTransport MAX-ACCESS read-only STATUS current DESCRIPTION "The underlying transport over which this L2TP tunnel is carried." ::= { rsL2tpTunnelStatusEntry 2 } rsL2tpTunnelStatusLocalTunnelId OBJECT-TYPE SYNTAX RsL2tpTunnelId MAX-ACCESS read-only STATUS current DESCRIPTION "The local tunnel identifier." ::= { rsL2tpTunnelStatusEntry 3 } rsL2tpTunnelStatusRemoteTunnelId OBJECT-TYPE SYNTAX RsL2tpTunnelId MAX-ACCESS read-only STATUS current DESCRIPTION "The remote tunnel identifier." ::= { rsL2tpTunnelStatusEntry 4 } rsL2tpTunnelStatusEffectiveAdminState OBJECT-TYPE SYNTAX RsL2tpAdminState MAX-ACCESS read-only STATUS current DESCRIPTION "The administrative state currently in effect. This could be the configured admin state for this tunnel, or an overriding admin state exerted from a higher hierarchical level (system, destination)." ::= { rsL2tpTunnelStatusEntry 5 } rsL2tpTunnelStatusState OBJECT-TYPE SYNTAX INTEGER { idle(0), connecting(1), established(2), disconnecting(3) } MAX-ACCESS read-only STATUS current DESCRIPTION "The current state of the tunnel." ::= { rsL2tpTunnelStatusEntry 6 } rsL2tpTunnelStatusInitiated OBJECT-TYPE SYNTAX INTEGER { none(0), local(1), remote(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates whether the tunnel was initiated locally, or by the remote tunnel peer." ::= { rsL2tpTunnelStatusEntry 7 } rsL2tpTunnelStatusRemoteHostName OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "The host name obtained during the tunnel establishment phase (via the Host Name AVP) of the L2TP peer. If the tunnel is idle, this object should maintain its value from the last time it was connected, or a zero-length string if no name was previously known." ::= { rsL2tpTunnelStatusEntry 8 } rsL2tpTunnelStatusRemoteVendorName OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "Identifies the vendor name of the peer's L2TP implementation. If the tunnel is idle, this object should maintain its value from the last time it was connected, of a zero-length string if no name was previously known." ::= { rsL2tpTunnelStatusEntry 9 } rsL2tpTunnelStatusRemoteFirmwareRevision OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The tunnel peer's firmware revision number. If the tunnel is idle, this object should maintain its value from the last time it was connected, or a zero value if no revision was previously known." ::= { rsL2tpTunnelStatusEntry 10 } rsL2tpTunnelStatusRemoteProtocolVersion OBJECT-TYPE SYNTAX OCTET STRING (SIZE(2)) MAX-ACCESS read-only STATUS current DESCRIPTION "The protocol version and revision of the tunnel peer's implementation. The first octet contains the protocol version. The second octet contains the protocol revision." ::= { rsL2tpTunnelStatusEntry 11 } rsL2tpTunnelStatusRemoteBearerCapabilities OBJECT-TYPE SYNTAX INTEGER { none(0), digital(1), analog(2), digitalAnalog(3) } MAX-ACCESS read-only STATUS current DESCRIPTION "The Bearer Capabilities of the tunnel peer. If the tunnel is idle this object should maintain its value from the last time it was connected, or 'none' if not previously known." ::= { rsL2tpTunnelStatusEntry 12 } rsL2tpTunnelStatusRemoteFramingCapabilities OBJECT-TYPE SYNTAX INTEGER { none(0), sync(1), async(2), syncAsync(3) } MAX-ACCESS read-only STATUS current DESCRIPTION "The Framing Capabilities of the tunnel peer. If the tunnel is idle this object should maintain its value from the last time it was connected, or 'none' if not previously known." ::= { rsL2tpTunnelStatusEntry 13 } rsL2tpTunnelStatusRecvWindowSize OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "The receive window size." ::= { rsL2tpTunnelStatusEntry 14 } rsL2tpTunnelStatusSendWindowSize OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "The tunnel peer's receive window size." ::= { rsL2tpTunnelStatusEntry 15 } rsL2tpTunnelStatusSendQueueDepth OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of control packets on transmit queue." ::= { rsL2tpTunnelStatusEntry 16 } rsL2tpTunnelStatusRecvSeq OBJECT-TYPE SYNTAX Integer32 (0..65535) MAX-ACCESS read-only STATUS current DESCRIPTION "The next sequence number expected in a received control packet." ::= { rsL2tpTunnelStatusEntry 17 } rsL2tpTunnelStatusRecvSeqAck OBJECT-TYPE SYNTAX Integer32 (0..65535) MAX-ACCESS read-only STATUS current DESCRIPTION "The last received sequence number that was acknowledged back to the tunnel peer." ::= { rsL2tpTunnelStatusEntry 18 } rsL2tpTunnelStatusSendSeq OBJECT-TYPE SYNTAX Integer32 (0..65535) MAX-ACCESS read-only STATUS current DESCRIPTION "The next sequence number to be sent in a transmitted control packet." ::= { rsL2tpTunnelStatusEntry 19 } rsL2tpTunnelStatusSendSeqAck OBJECT-TYPE SYNTAX Integer32 (0..65535) MAX-ACCESS read-only STATUS current DESCRIPTION "The send sequence number that the tunnel peer has acknowledged. The flow control state can be determined by subtracting the rsL2tpTunnelStatusSendSeq from rsL2tpTunnelStatusSendSeqAck and comparing this value to rsL2tpTunnelStatusSendWindowSize." ::= { rsL2tpTunnelStatusEntry 20 } rsL2tpTunnelStatusTotalSessions OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The total number of sessions that this tunnel has successfully connected through to its tunnel peer since this tunnel was created, including those that have since terminated." ::= { rsL2tpTunnelStatusEntry 21 } rsL2tpTunnelStatusFailedSessions OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of sessions that were initiated but failed to reach the established phase." ::= { rsL2tpTunnelStatusEntry 22 } rsL2tpTunnelStatusActiveSessions OBJECT-TYPE SYNTAX Gauge32 MAX-ACCESS read-only STATUS current DESCRIPTION "The current number of sessions in the established state." ::= { rsL2tpTunnelStatusEntry 23 } rsL2tpTunnelStatusLastResultCode OBJECT-TYPE SYNTAX Integer32 (0..65535) MAX-ACCESS read-only STATUS current DESCRIPTION "The last value of the result code as described in the Result Code AVP which caused the tunnel to disconnect." ::= { rsL2tpTunnelStatusEntry 24 } rsL2tpTunnelStatusLastErrorCode OBJECT-TYPE SYNTAX Integer32 (0..65535) MAX-ACCESS read-only STATUS current DESCRIPTION "The last value of the error code as described in the Result Code AVP which caused the tunnel to disconnect." ::= { rsL2tpTunnelStatusEntry 25 } rsL2tpTunnelStatusLastErrorMessage OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "The last value of the optional message as described in the Result Code AVP which caused the tunnel to disconnect." ::= { rsL2tpTunnelStatusEntry 26 } -- -- Tunnel-level Statistics -- rsL2tpTunnelStatTable OBJECT-TYPE SYNTAX SEQUENCE OF RsL2tpTunnelStatEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The L2TP tunnel statistics table. Describes the control and payload statistics for each L2TP tunnel. Each entry in this table has a corresponding entry in the Interfaces MIB ifTable, and in rsL2tpTunnelConfigTable." ::= { rsL2tpTunnelStatistics 1 } rsL2tpTunnelStatEntry OBJECT-TYPE SYNTAX RsL2tpTunnelStatEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Describes the L2TP control and payload statistics for an L2TP tunnel." INDEX { rsL2tpTunnelStatIfIndex } ::= { rsL2tpTunnelStatTable 1 } RsL2tpTunnelStatEntry ::= SEQUENCE { rsL2tpTunnelStatIfIndex InterfaceIndex, rsL2tpTunnelStatCtlRecvOctets Counter32, rsL2tpTunnelStatCtlRecvPackets Counter32, rsL2tpTunnelStatCtlRecvErrors Counter32, rsL2tpTunnelStatCtlRecvDiscards Counter32, rsL2tpTunnelStatCtlSendOctets Counter32, rsL2tpTunnelStatCtlSendPackets Counter32, rsL2tpTunnelStatCtlSendErrors Counter32, rsL2tpTunnelStatCtlSendDiscards Counter32, rsL2tpTunnelStatPayRecvOctets Counter32, rsL2tpTunnelStatPayRecvPackets Counter32, rsL2tpTunnelStatPayRecvErrors Counter32, rsL2tpTunnelStatPayRecvDiscards Counter32, rsL2tpTunnelStatPaySendOctets Counter32, rsL2tpTunnelStatPaySendPackets Counter32, rsL2tpTunnelStatPaySendErrors Counter32, rsL2tpTunnelStatPaySendDiscards Counter32, rsL2tpTunnelStatCtlRecvZLB Counter32, rsL2tpTunnelStatCtlRecvOutOfSequence Counter32, rsL2tpTunnelStatCtlRecvOutOfWindow Counter32, rsL2tpTunnelStatCtlSendZLB Counter32, rsL2tpTunnelStatCtlSendRetransmits Counter32 } rsL2tpTunnelStatIfIndex OBJECT-TYPE SYNTAX InterfaceIndex MAX-ACCESS not-accessible STATUS current DESCRIPTION "Same value as ifIndex for the corresponding entry in Interfaces MIB ifTable." ::= { rsL2tpTunnelStatEntry 1 } rsL2tpTunnelStatCtlRecvOctets OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of control octets received." ::= { rsL2tpTunnelStatEntry 2 } rsL2tpTunnelStatCtlRecvPackets OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of control packets received." ::= { rsL2tpTunnelStatEntry 3 } rsL2tpTunnelStatCtlRecvErrors OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of control packets incurring reception errors." ::= { rsL2tpTunnelStatEntry 4 } rsL2tpTunnelStatCtlRecvDiscards OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of control packets discarded after reception." ::= { rsL2tpTunnelStatEntry 5 } rsL2tpTunnelStatCtlSendOctets OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of control octets sent." ::= { rsL2tpTunnelStatEntry 6 } rsL2tpTunnelStatCtlSendPackets OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of control packets sent." ::= { rsL2tpTunnelStatEntry 7 } rsL2tpTunnelStatCtlSendErrors OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of control packets incurring transmission errors." ::= { rsL2tpTunnelStatEntry 8 } rsL2tpTunnelStatCtlSendDiscards OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of control packets discarded before transmission." ::= { rsL2tpTunnelStatEntry 9 } rsL2tpTunnelStatPayRecvOctets OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of payload octets received." ::= { rsL2tpTunnelStatEntry 10 } rsL2tpTunnelStatPayRecvPackets OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of payload packets received." ::= { rsL2tpTunnelStatEntry 11 } rsL2tpTunnelStatPayRecvErrors OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of payload packets incurring reception errors." ::= { rsL2tpTunnelStatEntry 12 } rsL2tpTunnelStatPayRecvDiscards OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of payload packets discarded after reception." ::= { rsL2tpTunnelStatEntry 13 } rsL2tpTunnelStatPaySendOctets OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of payload octets sent." ::= { rsL2tpTunnelStatEntry 14 } rsL2tpTunnelStatPaySendPackets OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of payload packets sent." ::= { rsL2tpTunnelStatEntry 15 } rsL2tpTunnelStatPaySendErrors OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of payload packets incurring transmission errors." ::= { rsL2tpTunnelStatEntry 16 } rsL2tpTunnelStatPaySendDiscards OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of payload packets discarded before transmission." ::= { rsL2tpTunnelStatEntry 17 } -- -- additional granularity -- rsL2tpTunnelStatCtlRecvZLB OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of Zero Length Body control packet acknowledgement packets that were received." ::= { rsL2tpTunnelStatEntry 18 } rsL2tpTunnelStatCtlRecvOutOfSequence OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of control packets not received in the correct sequence number order." ::= { rsL2tpTunnelStatEntry 19 } rsL2tpTunnelStatCtlRecvOutOfWindow OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of control packets received outside the offered receive window." ::= { rsL2tpTunnelStatEntry 20 } rsL2tpTunnelStatCtlSendZLB OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of Zero Length Body control packets sent." ::= { rsL2tpTunnelStatEntry 21 } rsL2tpTunnelStatCtlSendRetransmits OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of control packet send retransmissions." ::= { rsL2tpTunnelStatEntry 22 } -- -- Tunnel Mappings -- -- -- TunnelIf/SessionId -> SessionIf Mapping -- rsL2tpMapTifSidToSifTable OBJECT-TYPE SYNTAX SEQUENCE OF RsL2tpMapTifSidToSifEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Table of TunnelIf/SessionId -> SessionIf mappings." ::= { rsL2tpTunnelMap 1 } rsL2tpMapTifSidToSifEntry OBJECT-TYPE SYNTAX RsL2tpMapTifSidToSifEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A mapping of TunnelIf/SessionId to SessionIf." INDEX { rsL2tpMapTifSidToSifTunnelIfIndex, rsL2tpMapTifSidToSifLocalSessionId } ::= { rsL2tpMapTifSidToSifTable 1 } RsL2tpMapTifSidToSifEntry ::= SEQUENCE { rsL2tpMapTifSidToSifTunnelIfIndex InterfaceIndex, rsL2tpMapTifSidToSifLocalSessionId RsL2tpSessionId, rsL2tpMapTifSidToSifSessionIfIndex InterfaceIndex } rsL2tpMapTifSidToSifTunnelIfIndex OBJECT-TYPE SYNTAX InterfaceIndex MAX-ACCESS not-accessible STATUS current DESCRIPTION "The ifIndex of a tunnel interface." ::= { rsL2tpMapTifSidToSifEntry 1 } rsL2tpMapTifSidToSifLocalSessionId OBJECT-TYPE SYNTAX RsL2tpSessionId MAX-ACCESS not-accessible STATUS current DESCRIPTION "A local session ID on the associated tunnel interface." ::= { rsL2tpMapTifSidToSifEntry 2 } rsL2tpMapTifSidToSifSessionIfIndex OBJECT-TYPE SYNTAX InterfaceIndex MAX-ACCESS read-only STATUS current DESCRIPTION "The ifIndex of the session interface identified by this entry's Tunnel ifIndex and local Session Id pair." ::= { rsL2tpMapTifSidToSifEntry 3 } -- -- Tunnel ID -> Tunnel If -- rsL2tpMapTidToTifTable OBJECT-TYPE SYNTAX SEQUENCE OF RsL2tpMapTidToTifEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Map L2TP tunnel IDs to tunnel interfaces." ::= { rsL2tpTunnelMap 2 } rsL2tpMapTidToTifEntry OBJECT-TYPE SYNTAX RsL2tpMapTidToTifEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A mapping of L2TP tunnel ID to tunnel interface." INDEX { rsL2tpMapTidToTifLocalTunnelId } ::= { rsL2tpMapTidToTifTable 1 } RsL2tpMapTidToTifEntry ::= SEQUENCE { rsL2tpMapTidToTifLocalTunnelId RsL2tpTunnelId, rsL2tpMapTidToTifIfIndex InterfaceIndex } rsL2tpMapTidToTifLocalTunnelId OBJECT-TYPE SYNTAX RsL2tpTunnelId MAX-ACCESS not-accessible STATUS current DESCRIPTION "A local tunnel identifier." ::= { rsL2tpMapTidToTifEntry 1 } rsL2tpMapTidToTifIfIndex OBJECT-TYPE SYNTAX InterfaceIndex MAX-ACCESS read-only STATUS current DESCRIPTION "The ifIndex of the tunnel interface having the associated tunnel identifier." ::= { rsL2tpMapTidToTifEntry 2 } -- ...................................................................... -- L2TP Session Group -- ...................................................................... rsL2tpSessionConfig OBJECT IDENTIFIER ::= { rsL2tpSession 1 } rsL2tpSessionStatus OBJECT IDENTIFIER ::= { rsL2tpSession 2 } rsL2tpSessionStatistics OBJECT IDENTIFIER ::= { rsL2tpSession 3 } -- -- Session-level Configuration -- -- { rsL2tpSessionConfig 1 } reserved for "next ifIndex" acquisition rsL2tpSessionConfigTable OBJECT-TYPE SYNTAX SEQUENCE OF RsL2tpSessionConfigEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The L2TP session configuration table. Each entry in this table has a corresponding entry in the Interfaces MIB ifTable, and in rsL2tpSessionStatsTable." ::= { rsL2tpSessionConfig 2 } rsL2tpSessionConfigEntry OBJECT-TYPE SYNTAX RsL2tpSessionConfigEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Describes the configuration attributes of an L2TP session." INDEX { rsL2tpSessionConfigIfIndex } ::= { rsL2tpSessionConfigTable 1 } RsL2tpSessionConfigEntry ::= SEQUENCE { rsL2tpSessionConfigIfIndex InterfaceIndex, rsL2tpSessionConfigRowStatus RowStatus, rsL2tpSessionConfigAdminState RsL2tpAdminState } rsL2tpSessionConfigIfIndex OBJECT-TYPE SYNTAX InterfaceIndex MAX-ACCESS not-accessible STATUS current DESCRIPTION "Same value as ifIndex for the corresponding entry in Interfaces MIB ifTable." ::= { rsL2tpSessionConfigEntry 1 } rsL2tpSessionConfigRowStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "An implementation may choose not to support administrative configuration of tunnels." ::= { rsL2tpSessionConfigEntry 2 } rsL2tpSessionConfigAdminState OBJECT-TYPE SYNTAX RsL2tpAdminState MAX-ACCESS read-create STATUS current DESCRIPTION "The configured administrative state." DEFVAL { enabled } ::= { rsL2tpSessionConfigEntry 3 } -- -- L2TP Session-level Status and Statistics -- rsL2tpSessionStatusTable OBJECT-TYPE SYNTAX SEQUENCE OF RsL2tpSessionStatusEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The L2TP session status and statistics table." ::= { rsL2tpSessionStatus 1 } rsL2tpSessionStatusEntry OBJECT-TYPE SYNTAX RsL2tpSessionStatusEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An L2TP session interface status and statistics entry." INDEX { rsL2tpSessionStatusIfIndex } ::= { rsL2tpSessionStatusTable 1 } RsL2tpSessionStatusEntry ::= SEQUENCE { rsL2tpSessionStatusIfIndex InterfaceIndex, rsL2tpSessionStatusLacPppIfIndex InterfaceIndexOrZero, rsL2tpSessionStatusLocalSessionId RsL2tpSessionId, rsL2tpSessionStatusRemoteSessionId RsL2tpSessionId, rsL2tpSessionStatusUserName DisplayString, rsL2tpSessionStatusEffectiveAdminState RsL2tpAdminState, rsL2tpSessionStatusState INTEGER, rsL2tpSessionStatusCallType INTEGER, rsL2tpSessionStatusCallSerialNumber Integer32, rsL2tpSessionStatusTxConnectSpeed Integer32, rsL2tpSessionStatusRxConnectSpeed Integer32, rsL2tpSessionStatusCallBearerType INTEGER, rsL2tpSessionStatusFramingType INTEGER, rsL2tpSessionStatusPhysChanId Integer32, rsL2tpSessionStatusDnis DisplayString, rsL2tpSessionStatusClid DisplayString, rsL2tpSessionStatusSubAddress DisplayString, rsL2tpSessionStatusPrivateGroupId DisplayString, rsL2tpSessionStatusProxyLcp TruthValue, rsL2tpSessionStatusAuthMethod INTEGER, rsL2tpSessionStatusSequencingState INTEGER, rsL2tpSessionStatusSendSeq Integer32, rsL2tpSessionStatusRecvSeq Integer32 } rsL2tpSessionStatusIfIndex OBJECT-TYPE SYNTAX InterfaceIndex MAX-ACCESS not-accessible STATUS current DESCRIPTION "The ifIndex of an L2TP session interface." ::= { rsL2tpSessionStatusEntry 1 } rsL2tpSessionStatusLacPppIfIndex OBJECT-TYPE SYNTAX InterfaceIndexOrZero MAX-ACCESS read-only STATUS current DESCRIPTION "For pass-through PPP sessions (conventional LAC), the ifIndex of an associated local PPP interface through which the remote LAC client was connected. If unknown, this object contains a value of zero. For locally originated PPP sessions (LNS-like), this object has a value of zero." ::= { rsL2tpSessionStatusEntry 2 } rsL2tpSessionStatusLocalSessionId OBJECT-TYPE SYNTAX RsL2tpSessionId MAX-ACCESS read-only STATUS current DESCRIPTION "The local session ID for the session." ::= { rsL2tpSessionStatusEntry 3 } rsL2tpSessionStatusRemoteSessionId OBJECT-TYPE SYNTAX RsL2tpSessionId MAX-ACCESS read-only STATUS current DESCRIPTION "The remote session ID for the session." ::= { rsL2tpSessionStatusEntry 4 } rsL2tpSessionStatusUserName OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "The peer session name on this interface, typically the login name of the remote user. If the user name is unknown this object will contain a zero-length string." ::= { rsL2tpSessionStatusEntry 5 } rsL2tpSessionStatusEffectiveAdminState OBJECT-TYPE SYNTAX RsL2tpAdminState MAX-ACCESS read-only STATUS current DESCRIPTION "The administrative state currently in effect. This could be the configured admin state for this session, or an overriding admin state exerted from a higher hierarchical level (system, destination, tunnel)." ::= { rsL2tpSessionStatusEntry 6 } rsL2tpSessionStatusState OBJECT-TYPE SYNTAX INTEGER { idle(0), connecting(1), established(2), disconnecting(3) } MAX-ACCESS read-only STATUS current DESCRIPTION "The current state of the session." ::= { rsL2tpSessionStatusEntry 7 } rsL2tpSessionStatusCallType OBJECT-TYPE SYNTAX INTEGER { none(0), lacIncoming(1), lnsIncoming(2), lacOutgoing(3), lnsOutgoing(4) } MAX-ACCESS read-only STATUS current DESCRIPTION "The type of call and role this tunnel peer is providing for this session. For example, lacIncoming(1) indicates this tunnel peer is acting as a LAC and generated a Incoming-Call-Request to the tunnel peer (the LNS). Note that tunnel peers can be both LAC and LNS simultaneously." ::= { rsL2tpSessionStatusEntry 8 } rsL2tpSessionStatusCallSerialNumber OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The serial number assigned to this session." ::= { rsL2tpSessionStatusEntry 9 } rsL2tpSessionStatusTxConnectSpeed OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The last known transmit baud rate for this session." ::= { rsL2tpSessionStatusEntry 10 } rsL2tpSessionStatusRxConnectSpeed OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The last known receive baud rate for this session." ::= { rsL2tpSessionStatusEntry 11 } rsL2tpSessionStatusCallBearerType OBJECT-TYPE SYNTAX INTEGER { none(0), digital(1), analog(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "The bearer type of this session." ::= { rsL2tpSessionStatusEntry 12 } rsL2tpSessionStatusFramingType OBJECT-TYPE SYNTAX INTEGER { none(0), sync(1), async(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "The framing type of this session." ::= { rsL2tpSessionStatusEntry 13 } rsL2tpSessionStatusPhysChanId OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The physical channel identifier for the session. For pass-through PPP sessions, typically the ifIndex of the access interface lying below the PPP interface identified by rsL2tpSessionStatusLacPppIfIndex." ::= { rsL2tpSessionStatusEntry 14 } rsL2tpSessionStatusDnis OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "The Dialed Number Information String that the LAC obtained from the network for the session. If no DNIS was provided, a zero-length string will be returned." ::= { rsL2tpSessionStatusEntry 15 } rsL2tpSessionStatusClid OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "The Calling Line ID that the LAC obtained from the network for the session. If no CLID was provided, a zero-length string will be returned." ::= { rsL2tpSessionStatusEntry 16 } rsL2tpSessionStatusSubAddress OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "The SubAddress that the LAC obtained from the network for the session. If no SubAddress was provided, a zero-length string will be returned." ::= { rsL2tpSessionStatusEntry 17 } rsL2tpSessionStatusPrivateGroupId OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "The Private Group Identifier used for this tunneled session. If no Private Group Identifier was provided, a zero-length string will be returned." ::= { rsL2tpSessionStatusEntry 18 } rsL2tpSessionStatusProxyLcp OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates whether the LAC performed proxy LCP for this session." ::= { rsL2tpSessionStatusEntry 19 } rsL2tpSessionStatusAuthMethod OBJECT-TYPE SYNTAX INTEGER { none(0), pppChap(1), pppPap(2), pppMsChap(3) } MAX-ACCESS read-only STATUS current DESCRIPTION "The proxy authentication method employed by the LAC for the session. If rsL2tpSessionProxyLcp is false(2) this object reports a value of 'none' and should be ignored." ::= { rsL2tpSessionStatusEntry 20 } rsL2tpSessionStatusSequencingState OBJECT-TYPE SYNTAX INTEGER { none(0), remote(1), local(2), both(3) } MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates which tunnel peers have requested payload sequencing." ::= { rsL2tpSessionStatusEntry 21 } rsL2tpSessionStatusSendSeq OBJECT-TYPE SYNTAX Integer32 (0..65535) MAX-ACCESS read-only STATUS current DESCRIPTION "The next send sequence number." ::= { rsL2tpSessionStatusEntry 22 } rsL2tpSessionStatusRecvSeq OBJECT-TYPE SYNTAX Integer32 (0..65535) MAX-ACCESS read-only STATUS current DESCRIPTION "The next receive sequence number expected." ::= { rsL2tpSessionStatusEntry 23 } -- -- L2TP Session-level Statistics -- rsL2tpSessionStatTable OBJECT-TYPE SYNTAX SEQUENCE OF RsL2tpSessionStatEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The L2TP session statistics table." ::= { rsL2tpSessionStatistics 1 } rsL2tpSessionStatEntry OBJECT-TYPE SYNTAX RsL2tpSessionStatEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An L2TP session interface statistics entry." INDEX { rsL2tpSessionStatIfIndex } ::= { rsL2tpSessionStatTable 1 } RsL2tpSessionStatEntry ::= SEQUENCE { rsL2tpSessionStatIfIndex InterfaceIndex, rsL2tpSessionStatPayRecvOctets Counter32, rsL2tpSessionStatPayRecvPackets Counter32, rsL2tpSessionStatPayRecvErrors Counter32, rsL2tpSessionStatPayRecvDiscards Counter32, rsL2tpSessionStatPaySendOctets Counter32, rsL2tpSessionStatPaySendPackets Counter32, rsL2tpSessionStatPaySendErrors Counter32, rsL2tpSessionStatPaySendDiscards Counter32, rsL2tpSessionStatRecvOutOfSequence Counter32, rsL2tpSessionStatResequencingTimeouts Counter32 } rsL2tpSessionStatIfIndex OBJECT-TYPE SYNTAX InterfaceIndex MAX-ACCESS not-accessible STATUS current DESCRIPTION "The ifIndex of an L2TP session interface." ::= { rsL2tpSessionStatEntry 1 } rsL2tpSessionStatPayRecvOctets OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of payload octets received." ::= { rsL2tpSessionStatEntry 2 } rsL2tpSessionStatPayRecvPackets OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of payload packets received." ::= { rsL2tpSessionStatEntry 3 } rsL2tpSessionStatPayRecvErrors OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of payload packets incurring reception errors." ::= { rsL2tpSessionStatEntry 4 } rsL2tpSessionStatPayRecvDiscards OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of payload packets discarded after reception." ::= { rsL2tpSessionStatEntry 5 } rsL2tpSessionStatPaySendOctets OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of payload octets sent." ::= { rsL2tpSessionStatEntry 6 } rsL2tpSessionStatPaySendPackets OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of payload packets sent." ::= { rsL2tpSessionStatEntry 7 } rsL2tpSessionStatPaySendErrors OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of payload packets incurring transmission errors." ::= { rsL2tpSessionStatEntry 8 } rsL2tpSessionStatPaySendDiscards OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of payload packets discarded before transmission." ::= { rsL2tpSessionStatEntry 9 } -- -- other -- rsL2tpSessionStatRecvOutOfSequence OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of packets received out of sequence." ::= { rsL2tpSessionStatEntry 10 } rsL2tpSessionStatResequencingTimeouts OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of reassembly timeouts that have occurred." ::= { rsL2tpSessionStatEntry 11 } -- ...................................................................... -- L2TP Transport Group -- ...................................................................... -- -- UDP/IP Transport -- rsL2tpTransportUdpIp OBJECT IDENTIFIER ::= { rsL2tpTransport 1 } rsL2tpUdpIpSystem OBJECT IDENTIFIER ::= { rsL2tpTransportUdpIp 1 } rsL2tpUdpIpDestination OBJECT IDENTIFIER ::= { rsL2tpTransportUdpIp 2 } rsL2tpUdpIpTunnel OBJECT IDENTIFIER ::= { rsL2tpTransportUdpIp 3 } rsL2tpUdpIpSession OBJECT IDENTIFIER ::= { rsL2tpTransportUdpIp 4 } -- -- UDP/IP Destination -- rsL2tpUdpIpDestTable OBJECT-TYPE SYNTAX SEQUENCE OF RsL2tpUdpIpDestEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The L2TP UDP/IP destination table. Reports the UDP/IP characteristics of a L2TP UDP/IP destination. A L2TP UDP/IP destination is associated with a local router, a local IP address, and with a remote IP address for the L2TP peer. More specific UDP/IP detail per tunnel is reported in the rsL2tpUdpIpTunnelTable." ::= { rsL2tpUdpIpDestination 1 } rsL2tpUdpIpDestEntry OBJECT-TYPE SYNTAX RsL2tpUdpIpDestEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Describes the UDP/IP attributes of an L2TP destination." INDEX { rsL2tpUdpIpDestIfIndex } ::= { rsL2tpUdpIpDestTable 1 } RsL2tpUdpIpDestEntry ::= SEQUENCE { rsL2tpUdpIpDestIfIndex InterfaceIndex, rsL2tpUdpIpDestRouterIndex Unsigned32, rsL2tpUdpIpDestLocalAddress IpAddress, rsL2tpUdpIpDestRemoteAddress IpAddress } rsL2tpUdpIpDestIfIndex OBJECT-TYPE SYNTAX InterfaceIndex MAX-ACCESS not-accessible STATUS current DESCRIPTION "Same value as ifIndex for the corresponding entry in Interfaces MIB ifTable." ::= { rsL2tpUdpIpDestEntry 1 } rsL2tpUdpIpDestRouterIndex OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "The index of an entry in the rsRouterTable for the local router with which this L2TP destination interface is associated." ::= { rsL2tpUdpIpDestEntry 2 } rsL2tpUdpIpDestLocalAddress OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "This L2TP destination's local IP address." ::= { rsL2tpUdpIpDestEntry 3 } rsL2tpUdpIpDestRemoteAddress OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The IP address of the remote L2TP endpoint." ::= { rsL2tpUdpIpDestEntry 4 } -- -- UDP/IP Tunnel -- rsL2tpUdpIpTunnelTable OBJECT-TYPE SYNTAX SEQUENCE OF RsL2tpUdpIpTunnelEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The L2TP UDP/IP tunnel table. Reports the UDP/IP characteristics of L2TP UDP/IP tunnels. A L2TP UDP/IP tunnel is defined in terms of the local and remote IP addresses and UDP ports." ::= { rsL2tpUdpIpTunnel 1 } rsL2tpUdpIpTunnelEntry OBJECT-TYPE SYNTAX RsL2tpUdpIpTunnelEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An L2TP UDP/IP tunnel entry." INDEX { rsL2tpUdpIpTunnelIfIndex } ::= { rsL2tpUdpIpTunnelTable 1 } RsL2tpUdpIpTunnelEntry ::= SEQUENCE { rsL2tpUdpIpTunnelIfIndex InterfaceIndex, rsL2tpUdpIpTunnelRouterIndex Unsigned32, rsL2tpUdpIpTunnelLocalAddress IpAddress, rsL2tpUdpIpTunnelLocalPort Integer32, rsL2tpUdpIpTunnelRemoteAddress IpAddress, rsL2tpUdpIpTunnelRemotePort Integer32 } rsL2tpUdpIpTunnelIfIndex OBJECT-TYPE SYNTAX InterfaceIndex MAX-ACCESS not-accessible STATUS current DESCRIPTION "Same as the value of ifIndex for the corresponding entry in Interfaces MIB ifTable." ::= { rsL2tpUdpIpTunnelEntry 1 } rsL2tpUdpIpTunnelRouterIndex OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "The index of an entry in the rsRouterTable for the local router with which this L2TP tunnel interface is associated." ::= { rsL2tpUdpIpTunnelEntry 2 } rsL2tpUdpIpTunnelLocalAddress OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The local IP address for this UDP/IP tunnel." ::= { rsL2tpUdpIpTunnelEntry 3 } rsL2tpUdpIpTunnelLocalPort OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The local UDP port for this UDP/IP tunnel." ::= { rsL2tpUdpIpTunnelEntry 4 } rsL2tpUdpIpTunnelRemoteAddress OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The remote IP address for this UDP/IP tunnel." ::= { rsL2tpUdpIpTunnelEntry 5 } rsL2tpUdpIpTunnelRemotePort OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The remote UDP port for this UDP/IP tunnel." ::= { rsL2tpUdpIpTunnelEntry 6 } -- ++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++ -- conformance information -- ++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++ rsL2tpGroups OBJECT IDENTIFIER ::= { rsL2tpConformance 1 } rsL2tpCompliances OBJECT IDENTIFIER ::= { rsL2tpConformance 2 } -- -- compliance statements -- rsL2tpCompliance MODULE-COMPLIANCE STATUS current DESCRIPTION "The compliance statement for SNMPv2 entities which implement the L2TP MIB." MODULE -- this module -- unconditionally mandatory groups MANDATORY-GROUPS { rsL2tpConfigGroup, rsL2tpStatusGroup, rsL2tpStatGroup, rsL2tpMapGroup } ::= { rsL2tpCompliances 1 } -- units of conformance rsL2tpConfigGroup OBJECT-GROUP OBJECTS { rsL2tpSysConfigAdminState, rsL2tpSysConfigDestructTimeout, rsL2tpSysConfigIpChecksumEnable, rsL2tpDestConfigRowStatus, rsL2tpDestConfigAdminState, rsL2tpTunnelConfigRowStatus, rsL2tpTunnelConfigAdminState, rsL2tpSessionConfigRowStatus, rsL2tpSessionConfigAdminState } STATUS current DESCRIPTION "A collection of objects providing configuration information of the L2TP protocol, tunnels and sessions." ::= { rsL2tpGroups 1 } rsL2tpStatusGroup OBJECT-GROUP OBJECTS { rsL2tpSysStatusProtocolVersion, rsL2tpSysStatusVendorName, rsL2tpSysStatusFirmwareRev, rsL2tpSysStatusTotalDestinations, rsL2tpSysStatusFailedDestinations, rsL2tpSysStatusActiveDestinations, rsL2tpSysStatusTotalTunnels, rsL2tpSysStatusFailedTunnels, rsL2tpSysStatusFailedTunnelAuthens, rsL2tpSysStatusActiveTunnels, rsL2tpSysStatusTotalSessions, rsL2tpSysStatusFailedSessions, rsL2tpSysStatusActiveSessions, rsL2tpDestStatusEffectiveAdminState, rsL2tpDestStatusTotalTunnels, rsL2tpDestStatusFailedTunnels, rsL2tpDestStatusFailedTunnelAuthens, rsL2tpDestStatusActiveTunnels, rsL2tpDestStatusTotalSessions, rsL2tpDestStatusFailedSessions, rsL2tpDestStatusActiveSessions, rsL2tpTunnelStatusEffectiveAdminState, rsL2tpTunnelStatusLocalTunnelId, rsL2tpTunnelStatusRemoteTunnelId, rsL2tpTunnelStatusState, rsL2tpTunnelStatusInitiated, rsL2tpTunnelStatusRemoteHostName, rsL2tpTunnelStatusRemoteVendorName, rsL2tpTunnelStatusRemoteFirmwareRevision, rsL2tpTunnelStatusRemoteProtocolVersion, rsL2tpTunnelStatusRemoteBearerCapabilities, rsL2tpTunnelStatusRemoteFramingCapabilities, rsL2tpTunnelStatusRecvWindowSize, rsL2tpTunnelStatusSendWindowSize, rsL2tpTunnelStatusSendQueueDepth, rsL2tpTunnelStatusRecvSeq, rsL2tpTunnelStatusRecvSeqAck, rsL2tpTunnelStatusSendSeq, rsL2tpTunnelStatusSendSeqAck, rsL2tpTunnelStatusTotalSessions, rsL2tpTunnelStatusFailedSessions, rsL2tpTunnelStatusActiveSessions, rsL2tpTunnelStatusLastResultCode, rsL2tpTunnelStatusLastErrorCode, rsL2tpTunnelStatusLastErrorMessage, rsL2tpSessionStatusLacPppIfIndex, rsL2tpSessionStatusLocalSessionId, rsL2tpSessionStatusRemoteSessionId, rsL2tpSessionStatusUserName, rsL2tpSessionStatusState, rsL2tpSessionStatusCallType, rsL2tpSessionStatusCallSerialNumber, rsL2tpSessionStatusTxConnectSpeed, rsL2tpSessionStatusRxConnectSpeed, rsL2tpSessionStatusCallBearerType, rsL2tpSessionStatusFramingType, rsL2tpSessionStatusPhysChanId, rsL2tpSessionStatusDnis, rsL2tpSessionStatusClid, rsL2tpSessionStatusSubAddress, rsL2tpSessionStatusPrivateGroupId, rsL2tpSessionStatusProxyLcp, rsL2tpSessionStatusAuthMethod, rsL2tpSessionStatusSequencingState, rsL2tpSessionStatusSendSeq, rsL2tpSessionStatusRecvSeq } STATUS current DESCRIPTION "A collection of objects providing status of the L2TP protocol at the system, destination, tunnel, and session levels." ::= { rsL2tpGroups 2 } rsL2tpStatGroup OBJECT-GROUP OBJECTS { rsL2tpDestStatCtlRecvOctets, rsL2tpDestStatCtlRecvPackets, rsL2tpDestStatCtlRecvErrors, rsL2tpDestStatCtlRecvDiscards, rsL2tpDestStatCtlSendOctets, rsL2tpDestStatCtlSendPackets, rsL2tpDestStatCtlSendErrors, rsL2tpDestStatCtlSendDiscards, rsL2tpDestStatPayRecvOctets, rsL2tpDestStatPayRecvPackets, rsL2tpDestStatPayRecvErrors, rsL2tpDestStatPayRecvDiscards, rsL2tpDestStatPaySendOctets, rsL2tpDestStatPaySendPackets, rsL2tpDestStatPaySendErrors, rsL2tpDestStatPaySendDiscards, rsL2tpTunnelStatCtlRecvOctets, rsL2tpTunnelStatCtlRecvPackets, rsL2tpTunnelStatCtlRecvErrors, rsL2tpTunnelStatCtlRecvDiscards, rsL2tpTunnelStatCtlSendOctets, rsL2tpTunnelStatCtlSendPackets, rsL2tpTunnelStatCtlSendErrors, rsL2tpTunnelStatCtlSendDiscards, rsL2tpTunnelStatPayRecvOctets, rsL2tpTunnelStatPayRecvPackets, rsL2tpTunnelStatPayRecvErrors, rsL2tpTunnelStatPayRecvDiscards, rsL2tpTunnelStatPaySendOctets, rsL2tpTunnelStatPaySendPackets, rsL2tpTunnelStatPaySendErrors, rsL2tpTunnelStatPaySendDiscards, rsL2tpTunnelStatCtlRecvZLB, rsL2tpTunnelStatCtlRecvOutOfSequence, rsL2tpTunnelStatCtlRecvOutOfWindow, rsL2tpTunnelStatCtlSendZLB, rsL2tpTunnelStatCtlSendRetransmits, rsL2tpSessionStatPayRecvOctets, rsL2tpSessionStatPayRecvPackets, rsL2tpSessionStatPayRecvErrors, rsL2tpSessionStatPayRecvDiscards, rsL2tpSessionStatPaySendOctets, rsL2tpSessionStatPaySendPackets, rsL2tpSessionStatPaySendErrors, rsL2tpSessionStatPaySendDiscards, rsL2tpSessionStatRecvOutOfSequence, rsL2tpSessionStatResequencingTimeouts } STATUS current DESCRIPTION "A collection of objects providing statistics of the L2TP protocol at the destination, tunnel, and session levels." ::= { rsL2tpGroups 3 } rsL2tpMapGroup OBJECT-GROUP OBJECTS { rsL2tpMapTifSidToSifSessionIfIndex, rsL2tpMapTidToTifIfIndex } STATUS current DESCRIPTION "A collection of objects providing mapping associations among L2TP components." ::= { rsL2tpGroups 4 } rsL2tpUdpIpGroup OBJECT-GROUP OBJECTS { rsL2tpUdpIpDestRouterIndex, rsL2tpUdpIpDestLocalAddress, rsL2tpUdpIpDestRemoteAddress, rsL2tpUdpIpTunnelRouterIndex, rsL2tpUdpIpTunnelLocalAddress, rsL2tpUdpIpTunnelLocalPort, rsL2tpUdpIpTunnelRemoteAddress, rsL2tpUdpIpTunnelRemotePort } STATUS current DESCRIPTION "A collection of objects providing UDP/IP transport information for L2TP components." ::= { rsL2tpGroups 5 } END