-- 08/17/2001 dxc Changed OCTETSTRING(SIZE(8)) to Counter64 -- 06/29/2001 dxc Changed all "SnmpAdminString"s to "DisplayString"s and all "Counter64"s to "OCTET STRING (SIZE(8))"s -- 05/24/2001 dxc Added revision description -- 05/07/2001 dxc Changed fcConnUnitId and fcConnUnitPortIndex from "not-accessible" to "read-only" -- 05/10/2001 dxc Changed the types of fcConnUnitName, fcConnUnitInfo, fcConnUnitLocation, fcConnUnitContact -- and fcConnUnitPortName from "SnmpAdminString" to "DisplayString" FIBRE-CHANNEL-MGMT-MIB DEFINITIONS ::= BEGIN IMPORTS OBJECT-TYPE, NOTIFICATION-TYPE, MODULE-IDENTITY, Integer32, Unsigned32, Counter64, IpAddress, TimeTicks, mib-2 FROM SNMPv2-SMI TEXTUAL-CONVENTION, DisplayString, RowStatus FROM SNMPv2-TC MODULE-COMPLIANCE, OBJECT-GROUP, NOTIFICATION-GROUP FROM SNMPv2-CONF; fcMgmtMIB MODULE-IDENTITY LAST-UPDATED "200105080000Z" ORGANIZATION "IETF IPFC Working Group" CONTACT-INFO "S. Blumenau EMC Corporation 171 South Street Hopkinton, MA 01748-9103 U.S.A Tel: +1 508 435 1000 Fax: +1 508 435 4657 Email: blumenau_steven@emc.com" DESCRIPTION "The fibre channel management MIB module." REVISION "200105080000Z" DESCRIPTION "Changed fcConnUnitId and fcConnUnitPortIndex from not-accessible to read-only" REVISION "200012040000Z" DESCRIPTION "Made the following edits: - Used FcPortFCClass as the type for the fcConnUnitPortFCClassCap and fcConnUnitPortFCClassOp objects in the FcConnUnitPortEntry SEQUENCE statement. - Used fcConnUnitGlobalId instead of fcConnUnitId as notification objects in the fcConnUnitDeletedTrap and fcConnUnitEventTrap NOTIFICATION-TYPE macros." REVISION "200011260000Z" DESCRIPTION "The goal of this version was to re-write into SMIv2." REVISION "200004120000Z" DESCRIPTION "Initial revision, published as RFC XXXX." ::= { mib-2 8888 } -- TO BE ASSIGNED fcMgmtNotifications OBJECT IDENTIFIER ::= { fcMgmtMIB 0 } fcMgmtObjects OBJECT IDENTIFIER ::= { fcMgmtMIB 1 } fcMgmtConformance OBJECT IDENTIFIER ::= { fcMgmtMIB 2 } fcMgmtConfig OBJECT IDENTIFIER ::= { fcMgmtObjects 1 } fcMgmtNotifyFilter OBJECT IDENTIFIER ::= { fcMgmtObjects 2 } fcMgmtStatistics OBJECT IDENTIFIER ::= { fcMgmtObjects 3 } fcMgmtSNS OBJECT IDENTIFIER ::= { fcMgmtObjects 4 } fcMgmtCompliances OBJECT IDENTIFIER ::= { fcMgmtConformance 1 } fcMgmtGroups OBJECT IDENTIFIER ::= { fcMgmtConformance 2 } -- -- Textual conventions for this MIB -- FcNameId ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "Represents the Worldwide Name (WWN; IEEE 60-bit variety; standard part of T11 definitions for fibre channel) associated with a Fibre Channel (FC) entity." SYNTAX OCTET STRING (SIZE (8)) FcGlobalId ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "Represents the Worldwide Name (WWN; IEEE 124-bit variety) associated with a Fibre Channel (FC) entity." SYNTAX OCTET STRING (SIZE(16)) FcEventSeverity ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "The set of values which define the event severity that will be logged by this connectivity unit. Values unknown (1) through debug (9) are essentially self-explanatory; mark (10) means that all messages are logged." SYNTAX INTEGER { unknown (1), emergency (2), alert (3), critical (4), error (5), warning (6), notify (7), info (8), debug (9), mark (10) } FcUnitType ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "unknown (1) cannot be determined other (2) none of the following hub (3) passive connectivity unit supporting loop protocol. switch (4) active connectivity unit supporting multiple protocols. gateway (5) unit that converts not only the interface but also encapsulates the frame into another protocol. The assumption is that there are always two gateways connected together. For example, FC <-> ATM. converter (6) unit that converts from one interface to another. For example, FC <-> SCSI. hba (7) host bus adapter proxyAgent (8) software proxy-agent storageDevice (9) disk,cd,tape,etc host (10) host computer storageSubsystem (11) raid, library, etc module (12) subcomponent of a system swDriver (13) software driver storageAccessDevice (14) provides storage management and access for hetergeneous hosts and heterogeneous devices." SYNTAX INTEGER { unknown(1), other(2), hub(3), switch(4), gateway(5), converter(6), hba(7), proxyAgent(8), storageDevice(9), host(10), storageSubsystem(11), module(12), swDriver(13), storageAccessDevice(14) } FcPortFCClass ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "Represents the class(es) of service represented on a given port, in a given operational context." SYNTAX BITS { unknown (0), classF (1), class1 (2), class2 (3), class3 (4), class4 (5), class5 (6), class6 (7) } SnmpAdminString ::= TEXTUAL-CONVENTION DISPLAY-HINT "255a" STATUS current DESCRIPTION "An octet string containing administrative information, preferably in human-readable form. To facilitate internationalization, this information is represented using the ISO/IEC IS 10646-1 character set, encoded as an octet string using the UTF-8 transformation format described in [RFC2044]. Since additional code points are added by amendments to the 10646 standard from time to time, implementations must be prepared to encounter any code point from 0x00000000 to 0x7fffffff. The use of control codes should be avoided. When it is necessary to represent a newline, the control code sequence CR LF should be used. The use of leading or trailing white space should be avoided. For code points not directly supported by user interface hardware or software, an alternative means of entry and display, such as hexadecimal, may be provided. For information encoded in 7-bit US-ASCII, the UTF-8 encoding is identical to the US-ASCII encoding. Note that when this TC is used for an object that is used or envisioned to be used as an index, then a SIZE restriction must be specified so that the number sub-identifiers for any object instance do not exceed the limit of 128, as defined by [RFC1905]. " SYNTAX OCTET STRING (SIZE (0..255)) -- -- the connectivity unit group -- fcConnUnitNumber OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of connectivity units present on this system. May be a count of the boards in a chassis or the number of full boxes in a rack." -- AGENTCLAUSE -- " -- CLASS-COMMAND: -- CLASS-NAME: com.mcdata.console.snmp.mib.emc.EmcGetuNumber -- INSTANTIATE: each-time" -- END AGENTCLAUSE ::= { fcMgmtConfig 1 } fcConnURL OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "The top-level URL of the system. If it does not exist the value is an empty string. The URL format is implementation dependent and can have keywords embedded that are preceeded by a percent sign (eg, %USER). The following are the defined keywords that will be recognized and replaced with data during a launch: USER - replace with username PASSWORD - replace with password GLOBALID - replace with globalid SERIALNO - replace with serial number A management application will read this object from the MIB, provide values for any of the keywords listed above that are present in the string, and then use the URL to invoke or launch the program referenced." -- AGENTCLAUSE -- " -- CLASS-COMMAND: -- CLASS-NAME: com.mcdata.console.snmp.mib.emc.EmcGetSystemURL -- INSTANTIATE: each-time" -- END AGENTCLAUSE ::= { fcMgmtConfig 2 } -- -- The connectivity table contains general information on the -- system's connectivity units. -- fcConnUnitTable OBJECT-TYPE SYNTAX SEQUENCE OF FcConnUnitEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The connectivity table contains general information on the system's units. The number of entries is given by the value of fcConnUnitNumber. It is 1 for stand-alone systems." ::= { fcMgmtConfig 3 } fcConnUnitEntry OBJECT-TYPE SYNTAX FcConnUnitEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A connectivity unit entry containing objects for a particular unit." INDEX { fcConnUnitId } ::= { fcConnUnitTable 1 } FcConnUnitEntry ::= SEQUENCE { fcConnUnitId OCTET STRING, fcConnUnitGlobalId FcGlobalId, fcConnUnitType FcUnitType, fcConnUnitNumPorts Unsigned32, fcConnUnitState INTEGER, fcConnUnitStatus INTEGER, fcConnUnitProduct SnmpAdminString, fcConnUnitSerialNo SnmpAdminString, fcConnUnitUpTime TimeTicks, fcConnUnitUrl DisplayString, fcConnUnitDomainId OCTET STRING, fcConnUnitProxyMaster INTEGER, fcConnUnitPrincipal INTEGER, fcConnUnitNumSensors Unsigned32, fcConnUnitNumRevs Unsigned32, fcConnUnitModuleId OCTET STRING, fcConnUnitName SnmpAdminString, fcConnUnitInfo SnmpAdminString, fcConnUnitControl INTEGER, fcConnUnitContact SnmpAdminString, fcConnUnitLocation SnmpAdminString, fcConnUnitEventFilter FcEventSeverity, fcConnUnitNumEvents Unsigned32, fcConnUnitMaxEvents Unsigned32, fcConnUnitEventCurrID Unsigned32 } fcConnUnitId OBJECT-TYPE SYNTAX OCTET STRING (SIZE (16)) MAX-ACCESS read-only STATUS current DESCRIPTION "The unique identification for this connectivity unit among those within this proxy domain. The value MUST be unique within the proxy domain because it is the index variable for fcConnUnitTable. The value assigned to a given conectivity unit SHOULD be persistent across agent and unit resets. It SHOULD be the same as fcConnUnitGlobalId if fcConnUnitGlobalId is known and stable." -- AGENTCLAUSE -- " -- CLASS-COMMAND: You can write a small description -- CLASS-NAME: com.mcdata.console.snmp.mib.emc.EmcUnitTable -- INSTANTIATE: at-start" -- END AGENTCLAUSE ::= { fcConnUnitEntry 1 } fcConnUnitGlobalId OBJECT-TYPE SYNTAX FcGlobalId MAX-ACCESS read-only STATUS current DESCRIPTION "An optional global-scope identifier for this connectivity unit. It MUST be a WWN for this connectivity unit or 16 octets of value zero. WWN formats requiring fewer than 16 octets MUST be extended to 16 octets with trailing zero octets. If a WWN is used for fcConnUnitId, the same WWN MUST be used for fcConnUnitGlobalId. When a non-zero value is provided, it SHOULD be persistent across agent and unit resets. It SHOULD be globally unique. It SHOULD be one of these FC-PH/PH3 formats: IEEE (NAA=1) IEEE Extended (NAA=2) IEEE Registered (NAA=5). IEEE Registered extended (NAA=6). Use of the IEEE formats allows any IEEE-registered vendor to assure global uniqueness independently. The following are some references on IEEE WWN formats: http://standards.ieee.org/regauth/oui/tutorials/fibreformat.html http://standards.ieee.org/regauth/oui/tutorials/fibrecomp_id.html If one or more WWNs are associated with the connectivity unit via other management methods, one of them SHOULD be used for fcConnUnitGlobalId. If there is not a WWN assigned specifically to the connectivity unit, there is some merit, though not a requirement, to using a WWN assigned to (one of) its permanently attached FC/LAN interface(s). This can not risk uniqueness, though. As a counterexample, if your agent runs in a host and the host has an HBA, it is quite possible that agent, host, and HBA will all be distinct connectivity units, so the host and agent can not use the WWN of the HBA. Another example: If your hub has a built-in Ethernet port, it might be reasonable for the hub to use its LAN address (prefixed with the appropriate NAA) as its fcConnUnitId. But if the Ethernet were a replaceable PCCard, the hub should have an independent ID." -- AGENTCLAUSE -- " -- CLASS-COMMAND: You can write a small description -- CLASS-NAME: com.mcdata.console.snmp.mib.emc.EmcUnitTable -- INSTANTIATE: at-start" -- END AGENTCLAUSE ::= { fcConnUnitEntry 2 } fcConnUnitType OBJECT-TYPE SYNTAX FcUnitType MAX-ACCESS read-only STATUS current DESCRIPTION "The type of this connectivity unit." -- AGENTCLAUSE -- " -- CLASS-COMMAND: You can write a small description -- CLASS-NAME: com.mcdata.console.snmp.mib.emc.EmcUnitTable -- INSTANTIATE: at-start" -- END AGENTCLAUSE ::= { fcConnUnitEntry 3 } fcConnUnitNumPorts OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of physical ports in the connectivity unit (internal/embedded, external)." -- AGENTCLAUSE -- " -- CLASS-COMMAND: You can write a small description -- CLASS-NAME: com.mcdata.console.snmp.mib.emc.EmcUnitTable -- INSTANTIATE: at-start" -- END AGENTCLAUSE ::= { fcConnUnitEntry 4 } fcConnUnitState OBJECT-TYPE SYNTAX INTEGER { unknown(1), online(2), offline(3) } MAX-ACCESS read-only STATUS current DESCRIPTION "This object reports the overall state of the connectivity unit. The meaning of all values is essentially self-explanatory. Any of these values may occur with any of the fcConnUnitStatus values." -- AGENTCLAUSE -- " -- CLASS-COMMAND: You can write a small description -- CLASS-NAME: com.mcdata.console.snmp.mib.emc.EmcUnitTable -- INSTANTIATE: at-start" -- END AGENTCLAUSE ::= { fcConnUnitEntry 5 } fcConnUnitStatus OBJECT-TYPE SYNTAX INTEGER { unknown(1), unused(2), ok(3), warning(4), failed(5) } MAX-ACCESS read-only STATUS current DESCRIPTION "This object reports the overall status of the connectivity unit. The warning (4) value means that the connectivity unit needs attention; all other values are essentially self-explanatory. Any of these values may occur with any of the fcConnUnitState values." -- AGENTCLAUSE -- " -- CLASS-COMMAND: You can write a small description -- CLASS-NAME: com.mcdata.console.snmp.mib.emc.EmcUnitTable -- INSTANTIATE: at-start" -- END AGENTCLAUSE ::= { fcConnUnitEntry 6 } fcConnUnitProduct OBJECT-TYPE SYNTAX SnmpAdminString MAX-ACCESS read-only STATUS current DESCRIPTION "The connectivity unit vendor's product model name." -- AGENTCLAUSE -- " -- CLASS-COMMAND: You can write a small description -- CLASS-NAME: com.mcdata.console.snmp.mib.emc.EmcUnitTable -- INSTANTIATE: at-start" -- END AGENTCLAUSE ::= { fcConnUnitEntry 7 } fcConnUnitSerialNo OBJECT-TYPE SYNTAX SnmpAdminString MAX-ACCESS read-only STATUS current DESCRIPTION "The serial number identification for this connectivity unit." -- AGENTCLAUSE -- " -- CLASS-COMMAND: You can write a small description -- CLASS-NAME: com.mcdata.console.snmp.mib.emc.EmcUnitTable -- INSTANTIATE: at-start" -- END AGENTCLAUSE ::= { fcConnUnitEntry 8 } fcConnUnitUpTime OBJECT-TYPE SYNTAX TimeTicks MAX-ACCESS read-only STATUS current DESCRIPTION "The number of centiseconds since the last unit initialization." -- AGENTCLAUSE -- " -- CLASS-COMMAND: You can write a small description -- CLASS-NAME: com.mcdata.console.snmp.mib.emc.EmcUnitTable -- INSTANTIATE: at-start" -- END AGENTCLAUSE ::= { fcConnUnitEntry 9 } fcConnUnitUrl OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-only STATUS current DESCRIPTION "URL to launch a management application, if applicable. Otherwise empty string. In a standalone unit, this would be the same as the top-level URL. This has the same definition as fcConnURL for keywords." -- AGENTCLAUSE -- " -- CLASS-COMMAND: You can write a small description -- CLASS-NAME: com.mcdata.console.snmp.mib.emc.EmcUnitTable -- INSTANTIATE: at-start" -- END AGENTCLAUSE ::= { fcConnUnitEntry 10 } fcConnUnitDomainId OBJECT-TYPE SYNTAX OCTET STRING (SIZE(3)) MAX-ACCESS read-only STATUS current DESCRIPTION "24 bit Fibre Channel address ID of this connectivity unit. Following the fibre channel standard, the right-most bit of the right-most octet is for the least significant bit of the address value; the left-most bit of the left-most octet, if needed, is for the most significant bit of the address value. If this value is not applicable, all bits set to 1." -- AGENTCLAUSE -- " -- CLASS-COMMAND: You can write a small description -- CLASS-NAME: com.mcdata.console.snmp.mib.emc.EmcUnitTable -- INSTANTIATE: at-start" -- END AGENTCLAUSE ::= { fcConnUnitEntry 11 } fcConnUnitProxyMaster OBJECT-TYPE SYNTAX INTEGER { unknown(1), no(2), yes(3) } MAX-ACCESS read-only STATUS current DESCRIPTION "A value of 'yes' means this is the proxy master unit for a set of managed units. For example, this could be the only unit with a management card in it for a set of units. A standalone unit should return 'yes' for this object." -- AGENTCLAUSE -- " -- CLASS-COMMAND: You can write a small description -- CLASS-NAME: com.mcdata.console.snmp.mib.emc.EmcUnitTable -- INSTANTIATE: at-start" -- END AGENTCLAUSE ::= { fcConnUnitEntry 12 } fcConnUnitPrincipal OBJECT-TYPE SYNTAX INTEGER { unknown(1), no(2), yes(3) } MAX-ACCESS read-only STATUS current DESCRIPTION "Whether this connectivity unit is the principal unit within the group of fabric elements. If this value is not applicable, return unknown." -- AGENTCLAUSE -- " -- CLASS-COMMAND: You can write a small description -- CLASS-NAME: com.mcdata.console.snmp.mib.emc.EmcUnitTable -- INSTANTIATE: at-start" -- END AGENTCLAUSE ::= { fcConnUnitEntry 13 } fcConnUnitNumSensors OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of sensors in the fcConnUnitSensorTable." -- AGENTCLAUSE -- " -- CLASS-COMMAND: You can write a small description -- CLASS-NAME: com.mcdata.console.snmp.mib.emc.EmcUnitTable -- INSTANTIATE: at-start" -- END AGENTCLAUSE ::= { fcConnUnitEntry 14 } fcConnUnitNumRevs OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of revisions in the fcConnUnitRevsTable." -- AGENTCLAUSE -- " -- CLASS-COMMAND: You can write a small description -- CLASS-NAME: com.mcdata.console.snmp.mib.emc.EmcUnitTable -- INSTANTIATE: at-start" -- END AGENTCLAUSE ::= { fcConnUnitEntry 15 } fcConnUnitModuleId OBJECT-TYPE SYNTAX OCTET STRING (SIZE(16)) MAX-ACCESS read-only STATUS current DESCRIPTION "This is a unique id, persistent between boots, that can be used to group a set of connectivity units together into a module. The intended use would be to create a connectivity unit with a fcConnUnitType of 'module' to represent a physical or logical group of connectivity units. Then the members of the group would set the value of fcConnUnitId for this 'container' connectivity unit. fcConnUnitModuleId should be zeros if this connectivity unit is not part of a module." -- AGENTCLAUSE -- " -- CLASS-COMMAND: You can write a small description -- CLASS-NAME: com.mcdata.console.snmp.mib.emc.EmcUnitTable -- INSTANTIATE: at-start" -- END AGENTCLAUSE ::= { fcConnUnitEntry 16 } fcConnUnitName OBJECT-TYPE SYNTAX SnmpAdminString MAX-ACCESS read-write STATUS current DESCRIPTION "A name for this connectivity unit. This object value should be persistent between boots." -- AGENTCLAUSE -- " -- CLASS-COMMAND: You can write a small description -- CLASS-NAME: com.mcdata.console.snmp.mib.emc.EmcUnitTable -- INSTANTIATE: at-start" -- END AGENTCLAUSE ::= { fcConnUnitEntry 17 } fcConnUnitInfo OBJECT-TYPE SYNTAX SnmpAdminString MAX-ACCESS read-write STATUS current DESCRIPTION "Information about this connectivity unit. This object value should be persistent between boots." -- AGENTCLAUSE -- " -- CLASS-COMMAND: You can write a small description -- CLASS-NAME: com.mcdata.console.snmp.mib.emc.EmcUnitTable -- INSTANTIATE: at-start" -- END AGENTCLAUSE ::= { fcConnUnitEntry 18 } fcConnUnitControl OBJECT-TYPE SYNTAX INTEGER { unknown(1), invalid(2), resetConnUnitColdStart(3), resetConnUnitWarmStart(4), offlineConnUnit(5), onlineConnUnit(6) } MAX-ACCESS read-write STATUS current DESCRIPTION "This object is used to control the addressed connectivity unit. NOTE: 'ColdStart' and 'WarmStart' are as defined in mib-2 and are not meant to be a factory reset. resetConnUnitColdStart: the addressed unit performs a 'ColdStart' reset. resetConnUnitWarmStart: the addressed unit performs a 'WarmStart' reset. offlineConnUnit: the addressed unit puts itself into an implementation dependant 'offline' state. In general,if a unit is in an offline state, it cannot be used to perform meaningful Fibre Channel work. onlineConnUnit: the addressed unit puts itself into an implementation dependant 'online' state. In general, if a unit is in an online state, it is capable of performing meaningful Fibre Channel work. NOTE: Each implementation may chose not to support SNMP Set operations for any or all of these values. For Sets specifying varbinds for instances of this object and values not supported by a given implementation, the agent will return the SNMP WrongValue PDU error code." -- AGENTCLAUSE -- " -- CLASS-COMMAND: You can write a small description -- CLASS-NAME: com.mcdata.console.snmp.mib.emc.EmcUnitTable -- INSTANTIATE: at-start" -- END AGENTCLAUSE ::= { fcConnUnitEntry 19 } fcConnUnitContact OBJECT-TYPE SYNTAX SnmpAdminString MAX-ACCESS read-write STATUS current DESCRIPTION "Contact information for this connectivity unit. The contact information is intended to facilitate contacting someone in case of problems, questions, etc. (e.g., the a help desk internal to a company)." -- AGENTCLAUSE -- " -- CLASS-COMMAND: You can write a small description -- CLASS-NAME: com.mcdata.console.snmp.mib.emc.EmcUnitTable -- INSTANTIATE: at-start" -- END AGENTCLAUSE ::= { fcConnUnitEntry 20 } fcConnUnitLocation OBJECT-TYPE SYNTAX SnmpAdminString MAX-ACCESS read-write STATUS current DESCRIPTION "Location information for this connectivity unit." -- AGENTCLAUSE -- " -- CLASS-COMMAND: You can write a small description -- CLASS-NAME: com.mcdata.console.snmp.mib.emc.EmcUnitTable -- INSTANTIATE: at-start" -- END AGENTCLAUSE ::= { fcConnUnitEntry 21 } fcConnUnitEventFilter OBJECT-TYPE SYNTAX FcEventSeverity MAX-ACCESS read-write STATUS current DESCRIPTION "This value defines the event severity that will be logged by this connectivity unit. All events of severity less than or equal to fcConnUnitEventFilter are logged in the fcConnUnitEventTable." -- AGENTCLAUSE -- " -- CLASS-COMMAND: You can write a small description -- CLASS-NAME: com.mcdata.console.snmp.mib.emc.EmcUnitTable -- INSTANTIATE: at-start" -- END AGENTCLAUSE ::= { fcConnUnitEntry 22 } fcConnUnitNumEvents OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of events currently in the fcConnUnitEventTable." -- AGENTCLAUSE -- " -- CLASS-COMMAND: You can write a small description -- CLASS-NAME: com.mcdata.console.snmp.mib.emc.EmcUnitTable -- INSTANTIATE: at-start" -- END AGENTCLAUSE ::= { fcConnUnitEntry 23 } fcConnUnitMaxEvents OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "Max number of events that can be recorded at any one time in the fcConnUnitEventTable." -- AGENTCLAUSE -- " -- CLASS-COMMAND: You can write a small description -- CLASS-NAME: com.mcdata.console.snmp.mib.emc.EmcUnitTable -- INSTANTIATE: at-start" -- END AGENTCLAUSE ::= { fcConnUnitEntry 24 } fcConnUnitEventCurrID OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "The last used event ID (fcConnUnitEventId) recorded in the fcConnUnitEventTable. When no events are presently recorded in the fcConnUnitEventTable, the value of this object MUST be zero." -- AGENTCLAUSE -- " -- CLASS-COMMAND: You can write a small description -- CLASS-NAME: com.mcdata.console.snmp.mib.emc.EmcUnitTable -- INSTANTIATE: at-start" -- END AGENTCLAUSE ::= { fcConnUnitEntry 25 } -- -- The revisions table lists the revisions supported by the -- associated connectivity units. -- fcConnUnitRevsTable OBJECT-TYPE SYNTAX SEQUENCE OF FcConnUnitRevsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Table of the revisions of components (e.g., firmware, hardware, etc.) supported by the connectivity units managed by this agent." ::= { fcMgmtConfig 4 } fcConnUnitRevsEntry OBJECT-TYPE SYNTAX FcConnUnitRevsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A row in the fcConnUnitRevsTable." INDEX { fcConnUnitId, fcConnUnitRevsIndex } ::= { fcConnUnitRevsTable 1 } FcConnUnitRevsEntry ::= SEQUENCE { fcConnUnitRevsIndex Unsigned32, fcConnUnitRevsRevision SnmpAdminString, fcConnUnitRevsDescription SnmpAdminString } fcConnUnitRevsIndex OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS not-accessible STATUS current DESCRIPTION "A unique value among all fcConnUnitRevsEntrys with the same value of fcConnUnitId, in the range between 1 and fcConnUnitNumRevs[fcConnUnitId]." -- AGENTCLAUSE -- " -- CLASS-COMMAND: You can write a small description -- CLASS-NAME: com.mcdata.console.snmp.mib.emc.EmcUnitRevsTable -- INSTANTIATE: at-start" -- END AGENTCLAUSE ::= { fcConnUnitRevsEntry 1 } fcConnUnitRevsRevision OBJECT-TYPE SYNTAX SnmpAdminString MAX-ACCESS read-only STATUS current DESCRIPTION "A vendor-specific value identifying a revision of a component of the connectivity unit." -- AGENTCLAUSE -- " -- CLASS-COMMAND: You can write a small description -- CLASS-NAME: com.mcdata.console.snmp.mib.emc.EmcUnitRevsTable -- INSTANTIATE: at-start" -- END AGENTCLAUSE ::= { fcConnUnitRevsEntry 2 } fcConnUnitRevsDescription OBJECT-TYPE SYNTAX SnmpAdminString MAX-ACCESS read-only STATUS current DESCRIPTION "Description of a component in the ConnUnit to which the revision corresponds." -- AGENTCLAUSE -- " -- CLASS-COMMAND: You can write a small description -- CLASS-NAME: com.mcdata.console.snmp.mib.emc.EmcUnitRevsTable -- INSTANTIATE: at-start" -- END AGENTCLAUSE ::= { fcConnUnitRevsEntry 3 } -- -- The sensor table list the sensors supported by each -- connectivity unit. -- fcConnUnitSensorTable OBJECT-TYPE SYNTAX SEQUENCE OF FcConnUnitSensorEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Table of the sensors supported by each connectivity unit." ::= { fcMgmtConfig 5 } fcConnUnitSensorEntry OBJECT-TYPE SYNTAX FcConnUnitSensorEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Each entry contains the information for a specific sensor." INDEX { fcConnUnitId, fcConnUnitSensorIndex } ::= { fcConnUnitSensorTable 1 } FcConnUnitSensorEntry ::= SEQUENCE { fcConnUnitSensorIndex Unsigned32, fcConnUnitSensorName SnmpAdminString, fcConnUnitSensorStatus INTEGER, fcConnUnitSensorInfo SnmpAdminString, fcConnUnitSensorMessage SnmpAdminString, fcConnUnitSensorType INTEGER, fcConnUnitSensorCharacteristic INTEGER } fcConnUnitSensorIndex OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS not-accessible STATUS current DESCRIPTION "A unique value among all fcConnUnitSensorEntrys with the same value of fcConnUnitId, in the range between 1 and fcConnUnitNumSensors[fcConnUnitId]." -- AGENTCLAUSE -- " -- CLASS-COMMAND: You can write a small description -- CLASS-NAME: com.mcdata.console.snmp.mib.emc.EmcUnitSensorTable -- INSTANTIATE: at-start" -- END AGENTCLAUSE ::= { fcConnUnitSensorEntry 1 } fcConnUnitSensorName OBJECT-TYPE SYNTAX SnmpAdminString MAX-ACCESS read-only STATUS current DESCRIPTION "A textual identification of the sensor intended primarily for operator use." -- AGENTCLAUSE -- " -- CLASS-COMMAND: You can write a small description -- CLASS-NAME: com.mcdata.console.snmp.mib.emc.EmcUnitSensorTable -- INSTANTIATE: at-start" -- END AGENTCLAUSE ::= { fcConnUnitSensorEntry 2 } fcConnUnitSensorStatus OBJECT-TYPE SYNTAX INTEGER { unknown(1), other(2), ok(3), warning(4), failed(5) } MAX-ACCESS read-only STATUS current DESCRIPTION "The status indicated by the sensor. unknown (1) = the unit cannot determine the status other (2) = the status does not fit any of the remaining values ok (3) = indicates good status warning (4) = indicates the unit needs attention failed (5) = indicates the unit is non-functional" -- AGENTCLAUSE -- " -- CLASS-COMMAND: You can write a small description -- CLASS-NAME: com.mcdata.console.snmp.mib.emc.EmcUnitSensorTable -- INSTANTIATE: at-start" -- END AGENTCLAUSE ::= { fcConnUnitSensorEntry 3 } fcConnUnitSensorInfo OBJECT-TYPE SYNTAX SnmpAdminString MAX-ACCESS read-only STATUS current DESCRIPTION "Miscellaneous static information about the sensor such as its serial number." -- AGENTCLAUSE -- " -- CLASS-COMMAND: You can write a small description -- CLASS-NAME: com.mcdata.console.snmp.mib.emc.EmcUnitSensorTable -- INSTANTIATE: at-start" -- END AGENTCLAUSE ::= { fcConnUnitSensorEntry 4 } fcConnUnitSensorMessage OBJECT-TYPE SYNTAX SnmpAdminString MAX-ACCESS read-only STATUS current DESCRIPTION "This describes the status of the sensor as a message. It may also provide more resolution on the sensor indication, for example 'Cover temperature 1503K, above nominal operating range'" -- AGENTCLAUSE -- " -- CLASS-COMMAND: You can write a small description -- CLASS-NAME: com.mcdata.console.snmp.mib.emc.EmcUnitSensorTable -- INSTANTIATE: at-start" -- END AGENTCLAUSE ::= { fcConnUnitSensorEntry 5 } fcConnUnitSensorType OBJECT-TYPE SYNTAX INTEGER { unknown(1), other(2), battery(3), fan(4), powerSupply(5), transmitter(6), enclosure(7), board(8), receiver(9) } MAX-ACCESS read-only STATUS current DESCRIPTION "The type of component being monitored by this sensor. The unknown (1) and other (2) values meanings analogous to those for the fcConnUnitSensorStatus object; all other values are essentially self-explanatory." -- AGENTCLAUSE -- " -- CLASS-COMMAND: You can write a small description -- CLASS-NAME: com.mcdata.console.snmp.mib.emc.EmcUnitSensorTable -- INSTANTIATE: at-start" -- END AGENTCLAUSE ::= { fcConnUnitSensorEntry 6 } fcConnUnitSensorCharacteristic OBJECT-TYPE SYNTAX INTEGER { unknown(1), other(2), temperature(3), pressure(4), emf(5), currentValue(6), airflow(7), frequency(8), power(9) } MAX-ACCESS read-only STATUS current DESCRIPTION "The characteristics being monitored by this sensor. The unknown (1) and other (2) values meanings analogous to those for the fcConnUnitSensorStatus object; emf (5) refers to electro-magnetic field; all other values are essentially self-explanatory." -- AGENTCLAUSE -- " -- CLASS-COMMAND: You can write a small description -- CLASS-NAME: com.mcdata.console.snmp.mib.emc.EmcUnitSensorTable -- INSTANTIATE: at-start" -- END AGENTCLAUSE ::= { fcConnUnitSensorEntry 7 } -- -- The port table contains generic information on ports for a -- specific connectivity unit. -- fcConnUnitPortTable OBJECT-TYPE SYNTAX SEQUENCE OF FcConnUnitPortEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Generic information on ports for a specific connectivity unit." ::= { fcMgmtConfig 6 } fcConnUnitPortEntry OBJECT-TYPE SYNTAX FcConnUnitPortEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Each entry contains the information for a specific port." INDEX { fcConnUnitId, fcConnUnitPortIndex } ::= { fcConnUnitPortTable 1 } FcConnUnitPortEntry ::= SEQUENCE { fcConnUnitPortIndex Unsigned32, fcConnUnitPortType INTEGER, fcConnUnitPortFCClassCap FcPortFCClass, fcConnUnitPortFCClassOp FcPortFCClass, fcConnUnitPortState INTEGER, fcConnUnitPortStatus INTEGER, fcConnUnitPortTransmitterType INTEGER, fcConnUnitPortModuleType INTEGER, fcConnUnitPortWwn FcNameId, fcConnUnitPortFCId OCTET STRING, fcConnUnitPortSerialNo SnmpAdminString, fcConnUnitPortRevision SnmpAdminString, fcConnUnitPortVendor SnmpAdminString, fcConnUnitPortSpeed Gauge32, fcConnUnitPortControl INTEGER, fcConnUnitPortName SnmpAdminString, fcConnUnitPortPhysicalNumber Unsigned32, fcConnUnitPortProtocolCap OCTET STRING, fcConnUnitPortProtocolOp OCTET STRING, fcConnUnitPortNodeWwn FcNameId, fcConnUnitPortHWState INTEGER } fcConnUnitPortIndex OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "A unique value among all fcConnUnitPortEntrys on this connectivity unit, between 1 and fcConnUnitNumPorts." -- AGENTCLAUSE -- " -- CLASS-COMMAND: You can write a small description -- CLASS-NAME: com.mcdata.console.snmp.mib.emc.EmcUnitPortTable -- INSTANTIATE: at-start" -- END AGENTCLAUSE ::= { fcConnUnitPortEntry 1 } fcConnUnitPortType OBJECT-TYPE SYNTAX INTEGER { unknown (1), other (2), notPresent (3), hubPort (4), nPort (5), lPort (6), flPort (7), fPort (8), ePort (9), gPort (10), domainController (11), hubController (12), scsi (13), escon (14), lan (15), wan (16) } MAX-ACCESS read-only STATUS current DESCRIPTION "The port type refers to the protocol active on the port and can take one of the following values: unknown (1) - cannot be determined other (2) - none of the following: notPresent (3) - no port hubPort (4) - hub port nPort (5) - end port for fabric lPort (6) - end port for loop flPort (7) - public loop fPort (8) - fabric port ePort (9) - fabric expansion port gPort (10) - generic fabric port domainController (11) - domain controller hubController (12) - hub controller scsi (13) - parallel SCSI port escon (14) - escon port lan (15) - LAN port wan (16) - WAN port" -- AGENTCLAUSE -- " -- CLASS-COMMAND: You can write a small description -- CLASS-NAME: com.mcdata.console.snmp.mib.emc.EmcUnitPortTable -- INSTANTIATE: at-start" -- END AGENTCLAUSE ::= { fcConnUnitPortEntry 2 } fcConnUnitPortFCClassCap OBJECT-TYPE SYNTAX FcPortFCClass MAX-ACCESS read-only STATUS current DESCRIPTION "Bit mask that specifies the classes of service capability of this port. If this object is not applicable, the agent MUST return all bits set to zero." -- AGENTCLAUSE -- " -- CLASS-COMMAND: You can write a small description -- CLASS-NAME: com.mcdata.console.snmp.mib.emc.EmcUnitPortTable -- INSTANTIATE: at-start" -- END AGENTCLAUSE ::= { fcConnUnitPortEntry 3 } fcConnUnitPortFCClassOp OBJECT-TYPE SYNTAX FcPortFCClass MAX-ACCESS read-only STATUS current DESCRIPTION "Bit mask that specifies the classes of service that are currently operational at this port. If this object is not applicable, the agent MUST return all bits set to zero." -- AGENTCLAUSE -- " -- CLASS-COMMAND: You can write a small description -- CLASS-NAME: com.mcdata.console.snmp.mib.emc.EmcUnitPortTable -- INSTANTIATE: at-start" -- END AGENTCLAUSE ::= { fcConnUnitPortEntry 4 } fcConnUnitPortState OBJECT-TYPE SYNTAX INTEGER { unknown(1), online(2), offline(3), bypassed(4) } MAX-ACCESS read-only STATUS current DESCRIPTION "The current state of the port hardware. The bypassed value (4) means that the port is online but is currently being isolated from the loop or fabric for some reason; the other values are essentially self-explanatory. Any value for this object may co-exist with any value for the fcConnUnitPortStatus object." -- AGENTCLAUSE -- " -- CLASS-COMMAND: You can write a small description -- CLASS-NAME: com.mcdata.console.snmp.mib.emc.EmcUnitPortTable -- INSTANTIATE: at-start" -- END AGENTCLAUSE ::= { fcConnUnitPortEntry 5 } fcConnUnitPortStatus OBJECT-TYPE SYNTAX INTEGER { unknown (1), unused (2), ok (3), warning (4), failure (5), notParticipating (6), initializing (7), bypassed (8) } MAX-ACCESS read-only STATUS current DESCRIPTION "The current overall protocol status for the port. The warning value (4) means that the port needs attention; the notParticipating value (6) means that protocol is not being processed; the initializing value (7) means that the port is in the process of coming into service; the bypassed value (8) means that the port has been manually or automatically isolated from the loop or fabric; the other values are essentially self-explanatory. Any value for this object may co-exist with any value for the fcConnUnitPortState object." -- AGENTCLAUSE -- " -- CLASS-COMMAND: You can write a small description -- CLASS-NAME: com.mcdata.console.snmp.mib.emc.EmcUnitPortTable -- INSTANTIATE: at-start" -- END AGENTCLAUSE ::= { fcConnUnitPortEntry 6 } fcConnUnitPortTransmitterType OBJECT-TYPE SYNTAX INTEGER { unknown(1), other(2), unused(3), shortwave(4), longwave(5), copper(6), scsi(7), longwaveNoOFC(8), shortwaveNoOFC(9), longwaveLED(10) } MAX-ACCESS read-only STATUS current DESCRIPTION "The technology of the port transceiver." -- AGENTCLAUSE -- " -- CLASS-COMMAND: You can write a small description -- CLASS-NAME: com.mcdata.console.snmp.mib.emc.EmcUnitPortTable -- INSTANTIATE: at-start" -- END AGENTCLAUSE ::= { fcConnUnitPortEntry 7 } fcConnUnitPortModuleType OBJECT-TYPE SYNTAX INTEGER { unknown(1), other(2), gbic(3), embedded(4), glm(5), gbicSerialId(6), gbicNoSerialId(7), gbicNotInstalled(8), smallFormFactor(9) } MAX-ACCESS read-only STATUS current DESCRIPTION "The module type of the port connector. This object refers to the hardware implementation of the port. The embedded value (4) means 'fixed' (e.g., oneXnine)." -- AGENTCLAUSE -- " -- CLASS-COMMAND: You can write a small description -- CLASS-NAME: com.mcdata.console.snmp.mib.emc.EmcUnitPortTable -- INSTANTIATE: at-start" -- END AGENTCLAUSE ::= { fcConnUnitPortEntry 8 } fcConnUnitPortWwn OBJECT-TYPE SYNTAX FcNameId MAX-ACCESS read-only STATUS current DESCRIPTION "The World Wide Name of the port if applicable, otherwise empty string." -- AGENTCLAUSE -- " -- CLASS-COMMAND: You can write a small description -- CLASS-NAME: com.mcdata.console.snmp.mib.emc.EmcUnitPortTable -- INSTANTIATE: at-start" -- END AGENTCLAUSE ::= { fcConnUnitPortEntry 9 } fcConnUnitPortFCId OBJECT-TYPE SYNTAX OCTET STRING (SIZE(3)) MAX-ACCESS read-only STATUS current DESCRIPTION "This is the assigned Fibre Channel ID of this port. This value is expected to be a Big Endian value of 24 bits. If this is loop, then it is the ALPA that is connected. If this is an eport, then it will only contain the domain ID left justified, zero filled. If this port does not have a Fibre Channel address, return all bits set to 1." -- AGENTCLAUSE -- " -- CLASS-COMMAND: You can write a small description -- CLASS-NAME: com.mcdata.console.snmp.mib.emc.EmcUnitPortTable -- INSTANTIATE: at-start" -- END AGENTCLAUSE ::= { fcConnUnitPortEntry 10 } fcConnUnitPortSerialNo OBJECT-TYPE SYNTAX SnmpAdminString MAX-ACCESS read-only STATUS current DESCRIPTION "The serial number identification of the unit (e.g., for a GBIC). If this is not applicable, return a zero-length string." -- AGENTCLAUSE -- " -- CLASS-COMMAND: You can write a small description -- CLASS-NAME: com.mcdata.console.snmp.mib.emc.EmcUnitPortTable -- INSTANTIATE: at-start" -- END AGENTCLAUSE ::= { fcConnUnitPortEntry 11 } fcConnUnitPortRevision OBJECT-TYPE SYNTAX SnmpAdminString MAX-ACCESS read-only STATUS current DESCRIPTION "The port revision (e.g., for a GBIC)." -- AGENTCLAUSE -- " -- CLASS-COMMAND: You can write a small description -- CLASS-NAME: com.mcdata.console.snmp.mib.emc.EmcUnitPortTable -- INSTANTIATE: at-start" -- END AGENTCLAUSE ::= { fcConnUnitPortEntry 12 } fcConnUnitPortVendor OBJECT-TYPE SYNTAX SnmpAdminString MAX-ACCESS read-only STATUS current DESCRIPTION "The port vendor (e.g., for a GBIC)." -- AGENTCLAUSE -- " -- CLASS-COMMAND: You can write a small description -- CLASS-NAME: com.mcdata.console.snmp.mib.emc.EmcUnitPortTable -- INSTANTIATE: at-start" -- END AGENTCLAUSE ::= { fcConnUnitPortEntry 13 } fcConnUnitPortSpeed OBJECT-TYPE SYNTAX Gauge32 UNITS "kilobytes per second" MAX-ACCESS read-only STATUS current DESCRIPTION "The speed of the port in kilobytes per second." -- AGENTCLAUSE -- " -- CLASS-COMMAND: You can write a small description -- CLASS-NAME: com.mcdata.console.snmp.mib.emc.EmcUnitPortTable -- INSTANTIATE: at-start" -- END AGENTCLAUSE ::= { fcConnUnitPortEntry 14 } fcConnUnitPortControl OBJECT-TYPE SYNTAX INTEGER { unknown (1), invalid (2), resetConnUnitPort (3), bypassConnUnitPort (4), unbypassConnUnitPort (5), offlineConnUnitPort (6), onlineConnUnitPort (7) } MAX-ACCESS read-write STATUS current DESCRIPTION "This object is used to control the addressed fcConnUnit's port. Valid commands are: unknown and invalid are only used as values that are read. resetConnUnitPort (3): If the addressed connectivity unit allows this operation to be performed on this port, the addressed port performs a vendor-specific 'reset' operation. Examples of these operations are: the Link Reset protocol, the Loop Initialization protocol, or a resynchronization occurring between the transceiver in the addressed port to the transceiver that the port is connected to. bypassConnUnitPort (4): If the addressed connectivity unit allows this operation to be performed to this port, the addressed port performs a vendor-specific 'bypass' operation. Examples of these operations are: transitioning from online to offline, a request (NON- PARTICIPATING) command to the Loop Port state machine, or removal of the port from an arbitrated loop by a hub. unbypassConnUnitPort (5): If the addressed connectivity unit allows this operation to be performed to this port, the addressed port performs a vendor-specific 'unbypass' operation. Examples of these operations are: the Link Failure protocol, a request (PARTICIPATING) command to the Loop Port state machine, or addition of the port to an arbitrated loop by a hub. offlineConnUnitPort (6): If the addressed connectivity unit allows this operation to be performed to this port, the addressed port performs a vendor-specific 'offline' operation. Examples of these operations are: disabling a port's transceiver, the Link Failure protocol, request (NON-PARTICIPATING) command to the Loop Port state machine, or removal of the port from an arbitrated loop by a hub. onlineConnUnitPort (7): If the addressed connectivity unit allows this operation to be performed to this port, the addressed port performs a vendor-specific 'online' operation. Examples of these operations are: enabling a port's transceiver, the Link Failure protocol, request (PARTICIPATING) command to the Loop Port state machine, or addition of the port from an arbitrated loop by a hub. NOTE: Each implementation may chose not to support SNMP Set operations for any or all of these values. For Sets specifying varbinds for instances of this object and values not supported by a given implementation, the agent will return the SNMP WrongValue PDU error code." -- AGENTCLAUSE -- " -- CLASS-COMMAND: You can write a small description -- CLASS-NAME: com.mcdata.console.snmp.mib.emc.EmcUnitPortTable -- INSTANTIATE: at-start" -- END AGENTCLAUSE ::= { fcConnUnitPortEntry 15 } fcConnUnitPortName OBJECT-TYPE SYNTAX SnmpAdminString MAX-ACCESS read-write STATUS current DESCRIPTION "A string describing the addressed port." -- AGENTCLAUSE -- " -- CLASS-COMMAND: You can write a small description -- CLASS-NAME: com.mcdata.console.snmp.mib.emc.EmcUnitPortTable -- INSTANTIATE: at-start" -- END AGENTCLAUSE ::= { fcConnUnitPortEntry 16 } fcConnUnitPortPhysicalNumber OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This is the internal port number this port is known by. In many implementations, this should be the same as fcConnUnitPortIndex. Some implementations may have an internal port representation not compatible with the rules for table indices. In that case, provide the internal representation of this port in this object. This value may also be used in the fcConnUnitLinkPortNumberX or fcConnUnitLinkPortNumberY objects of the fcConnUnitLinkTable." -- AGENTCLAUSE -- " -- CLASS-COMMAND: You can write a small description -- CLASS-NAME: com.mcdata.console.snmp.mib.emc.EmcUnitPortTable -- INSTANTIATE: at-start" -- END AGENTCLAUSE ::= { fcConnUnitPortEntry 17 } fcConnUnitPortProtocolCap OBJECT-TYPE SYNTAX OCTET STRING (SIZE (2)) MAX-ACCESS read-only STATUS current DESCRIPTION "Bit mask that specifies the driver level protocol capability of this port. If this is not applicable, return all bits set to zero. The bits have the following definition: unknown - 0 Loop - 1 Fabric - 2 SCSI - 4 TCP/IP - 8 VI - 16 FICON - 32" -- AGENTCLAUSE -- " -- CLASS-COMMAND: You can write a small description -- CLASS-NAME: com.mcdata.console.snmp.mib.emc.EmcUnitPortTable -- INSTANTIATE: at-start" -- END AGENTCLAUSE ::= { fcConnUnitPortEntry 18 } fcConnUnitPortProtocolOp OBJECT-TYPE SYNTAX OCTET STRING (SIZE (2)) MAX-ACCESS read-only STATUS current DESCRIPTION "Bit mask that specifies the driver level protocol(s) that are currently operational. If this is not applicable, return all bits set to zero. This object has the same definition as fcConnUnitPortProtocolCap" -- AGENTCLAUSE -- " -- CLASS-COMMAND: You can write a small description -- CLASS-NAME: com.mcdata.console.snmp.mib.emc.EmcUnitPortTable -- INSTANTIATE: at-start" -- END AGENTCLAUSE ::= { fcConnUnitPortEntry 19 } fcConnUnitPortNodeWwn OBJECT-TYPE SYNTAX FcNameId MAX-ACCESS read-only STATUS current DESCRIPTION "The Node World Wide Name of the port if applicable, otherwise all zeros. This should have the same value for a group of related ports. The container is defined as the largest physical entity. For example, all ports on HBAs on a host will have the same Node WWN. All ports on the same storage subsystem will have the ame Node WWN." -- AGENTCLAUSE -- " -- CLASS-COMMAND: You can write a small description -- CLASS-NAME: com.mcdata.console.snmp.mib.emc.EmcUnitPortTable -- INSTANTIATE: at-start" -- END AGENTCLAUSE ::= { fcConnUnitPortEntry 20 } fcConnUnitPortHWState OBJECT-TYPE SYNTAX INTEGER { unknown (1), failed (2), -- port failed diagnostics bypassed (3), -- FCAL bypass, loop only active (4), -- connected to a device loopback (5), -- Port in ext loopback txfault (6), -- Transmitter fault noMedia (7), -- media not installed linkDown (8) -- waiting for activity (rx sync) } MAX-ACCESS read-only STATUS current DESCRIPTION "The hardware detected state of the port." -- AGENTCLAUSE -- " -- CLASS-COMMAND: You can write a small description -- CLASS-NAME: com.mcdata.console.snmp.mib.emc.EmcUnitPortTable -- INSTANTIATE: at-start" -- END AGENTCLAUSE ::= { fcConnUnitPortEntry 21 } -- -- event group -- fcConnUnitEventTable OBJECT-TYPE SYNTAX SEQUENCE OF FcConnUnitEventEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The table of connectivity unit events. Errors, warnings, and information should be reported in this table." ::= { fcMgmtConfig 7 } fcConnUnitEventEntry OBJECT-TYPE SYNTAX FcConnUnitEventEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Each entry contains information on a specific event for the given connectivity unit." INDEX { fcConnUnitId, fcConnUnitEventIndex } ::= { fcConnUnitEventTable 1 } FcConnUnitEventEntry ::= SEQUENCE { fcConnUnitEventIndex Unsigned32, fcConnUnitREventTime DisplayString, fcConnUnitSEventTime TimeTicks, fcConnUnitEventSeverity FcEventSeverity, fcConnUnitEventType INTEGER, fcConnUnitEventObject OBJECT IDENTIFIER, fcConnUnitEventDescr SnmpAdminString} fcConnUnitEventIndex OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "Each connectivity unit has its own event buffer. As it wraps, it may write over previous events. This object is an index into the buffer. It is recommended that this table be read using 'getNext's to retrieve the initial table. The management application should read the event table at periodic intervals and then determine if any new entries were added by comparing the last known index value with the current highest index value. The management application should then update its copy of the event table. If the read interval is too long, it is possible that there may be events that may not be contained in the agent's internal event buffer. For example, an agent may read events 50-75. At the next read interval, fcConnUnitEventCurrID is 189. If the management app tries to read event index 76, and the agent's internal buffer is 100 entries max, event index 76 will no longer be available. The index value is an incrementing integer starting from one every time there is a table reset. On table reset, all contents are emptied and all indeces are set to zero. When an event is added to the table, the event is assigned the next higher integer value than the last item entered into the table. If the index value reaches its maximum value, the next item entered will cause the index value to roll over and start at one again." -- AGENTCLAUSE -- " -- CLASS-COMMAND: You can write a small description -- CLASS-NAME: com.mcdata.console.snmp.mib.emc.EmcUnitEventTable -- INSTANTIATE: at-start" -- END AGENTCLAUSE ::= { fcConnUnitEventEntry 1 } fcConnUnitREventTime OBJECT-TYPE SYNTAX DisplayString (SIZE (15)) MAX-ACCESS read-only STATUS current DESCRIPTION "This is the real time when the event occurred. It has the following format. DDMMYYYY HHMMSS DD=day number MM=month number YYYY=year number HH=hour number MM=minute number SS=seconds number If not applicable, return a NULL string." -- AGENTCLAUSE -- " -- CLASS-COMMAND: You can write a small description -- CLASS-NAME: com.mcdata.console.snmp.mib.emc.EmcUnitEventTable -- INSTANTIATE: at-start" -- END AGENTCLAUSE ::= { fcConnUnitEventEntry 2 } fcConnUnitSEventTime OBJECT-TYPE SYNTAX TimeTicks MAX-ACCESS read-only STATUS current DESCRIPTION "This is the sysuptime timestamp when the event occurred." -- AGENTCLAUSE -- " -- CLASS-COMMAND: You can write a small description -- CLASS-NAME: com.mcdata.console.snmp.mib.emc.EmcUnitEventTable -- INSTANTIATE: at-start" -- END AGENTCLAUSE ::= { fcConnUnitEventEntry 3 } fcConnUnitEventSeverity OBJECT-TYPE SYNTAX FcEventSeverity MAX-ACCESS read-only STATUS current DESCRIPTION "The event severity level." -- AGENTCLAUSE -- " -- CLASS-COMMAND: You can write a small description -- CLASS-NAME: com.mcdata.console.snmp.mib.emc.EmcUnitEventTable -- INSTANTIATE: at-start" -- END AGENTCLAUSE ::= { fcConnUnitEventEntry 4 } fcConnUnitEventType OBJECT-TYPE SYNTAX INTEGER { unknown(1), other(2), status(3), configuration(4), topology(5) } MAX-ACCESS read-only STATUS current DESCRIPTION "The type of this event." -- AGENTCLAUSE -- " -- CLASS-COMMAND: You can write a small description -- CLASS-NAME: com.mcdata.console.snmp.mib.emc.EmcUnitEventTable -- INSTANTIATE: at-start" -- END AGENTCLAUSE ::= { fcConnUnitEventEntry 5 } fcConnUnitEventObject OBJECT-TYPE SYNTAX OBJECT IDENTIFIER MAX-ACCESS read-only STATUS current DESCRIPTION "This is used with the fcConnUnitEventType to identify which object the event refers to. It can be the OID of a connectivity unit or of another object like fcConnUnitPortStatus[...]" -- AGENTCLAUSE -- " -- CLASS-COMMAND: You can write a small description -- CLASS-NAME: com.mcdata.console.snmp.mib.emc.EmcUnitEventTable -- INSTANTIATE: at-start" -- END AGENTCLAUSE ::= { fcConnUnitEventEntry 6 } fcConnUnitEventDescr OBJECT-TYPE SYNTAX SnmpAdminString MAX-ACCESS read-only STATUS current DESCRIPTION "The description of the event." -- AGENTCLAUSE -- " -- CLASS-COMMAND: You can write a small description -- CLASS-NAME: com.mcdata.console.snmp.mib.emc.EmcUnitEventTable -- INSTANTIATE: at-start" -- END AGENTCLAUSE ::= { fcConnUnitEventEntry 7 } -- -- The link table is intended to organize and communicate -- any information the agent possesses which would assist a -- management application to discover the CONNECTIVITY UNITS -- in the framework and the TOPOLOGY of their interconnect. -- That is, the goal is to assist a management application -- to both LIST and MAP the elements of the framework. -- -- With this goal in mind, the agent SHOULD include as much -- information as it possesses about any links from its own -- connectivity units to others, including links among its -- own units. -- -- An agent SHOULD include partial information about links if -- it is not able to fully define them in accord with the -- following structure; however, the information MUST include -- either a nonzero fcConnUnitNodeId OR a nonzero -- fcConnUnitPortWwn for each end of the link. -- -- If the agent is able to discover links which do not directly -- attach to members of its agency and its discovery algorithm -- gives some assurance the links are recently valid, it MAY -- include these links. -- -- Link information entered by administrative action MAY be -- included even if not validated directly if the link has at -- least one endpoint in this agency, but SHOULD NOT be included -- otherwise. -- -- A connectivity unit should fill the table in as best it can. -- One of the methods to fill this in would be to use the RNID -- ELS (ANSI document 99-422v0). This allows one to query a -- port for the information needed for the link table. -- -- This table is MAX-ACCESSed either directly if the management -- software has an index value or via GetNexts. The value of -- the indexes are not required to be contiguous. Each entry -- created in this table will be assigned an index. This -- relationship is kept persistent until the entry is removed -- from the table or the system is reset. The total number of -- entries are defined by the size of the table -- For an entry to be considered to be valid, both the X (local) -- and the Y (remote) need to have one valid value. fcConnUnitLinkTable OBJECT-TYPE SYNTAX SEQUENCE OF FcConnUnitLinkEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A list of links know to this agent from this connectivity unit to other connectivity units." ::= { fcMgmtConfig 8 } fcConnUnitLinkEntry OBJECT-TYPE SYNTAX FcConnUnitLinkEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry describing a particular link to another." INDEX { fcConnUnitId, fcConnUnitLinkIndex } ::= { fcConnUnitLinkTable 1 } FcConnUnitLinkEntry ::= SEQUENCE { fcConnUnitLinkIndex Unsigned32, fcConnUnitLinkNodeIdX OCTET STRING, fcConnUnitLinkPortNumberX Integer32, fcConnUnitLinkPortWwnX OCTET STRING, fcConnUnitLinkNodeIdY OCTET STRING, fcConnUnitLinkPortNumberY Integer32, fcConnUnitLinkPortWwnY OCTET STRING, fcConnUnitLinkAgentAddressY OCTET STRING, fcConnUnitLinkAgentAddressTypeY Unsigned32, fcConnUnitLinkAgentPortY Unsigned32, fcConnUnitLinkUnitTypeY FcUnitType, fcConnUnitLinkConnIdY OCTET STRING } fcConnUnitLinkIndex OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "This value is used to create a unique value for each entry in the link table with the same fcConnUnitId. The value can only be reused if it is not currently in use and the value is the next candidate to be used. This value is allowed to wrap at the highest value represented by the number of bits. This value is reset to zero when the system is reset and the first value to be used is 1." -- AGENTCLAUSE -- " -- CLASS-COMMAND: You can write a small description -- CLASS-NAME: com.mcdata.console.snmp.mib.emc.EmcUnitLinkTable -- INSTANTIATE: at-start" -- END AGENTCLAUSE ::= { fcConnUnitLinkEntry 1 } fcConnUnitLinkNodeIdX OBJECT-TYPE SYNTAX OCTET STRING (SIZE(64)) MAX-ACCESS read-only STATUS current DESCRIPTION "The node WWN of the unit at one end of the link. If the node WWN is unknown and the node is an fcConnUnit in the responding agent then the value of this object MUST be equal to its fcConnUnitId." -- AGENTCLAUSE -- " -- CLASS-COMMAND: You can write a small description -- CLASS-NAME: com.mcdata.console.snmp.mib.emc.EmcUnitLinkTable -- INSTANTIATE: at-start" -- END AGENTCLAUSE ::= { fcConnUnitLinkEntry 2 } fcConnUnitLinkPortNumberX OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The port number on the unit specified by fcConnUnitLinkNodeIdX if known, otherwise -1. If the value is non-negative then it will be equal to fcConnUnitPortPhysicalNumber." -- AGENTCLAUSE -- " -- CLASS-COMMAND: You can write a small description -- CLASS-NAME: com.mcdata.console.snmp.mib.emc.EmcUnitLinkTable -- INSTANTIATE: at-start" -- END AGENTCLAUSE ::= { fcConnUnitLinkEntry 3 } fcConnUnitLinkPortWwnX OBJECT-TYPE SYNTAX OCTET STRING (SIZE(16)) MAX-ACCESS read-only STATUS current DESCRIPTION "The port WWN of the unit specified by fcConnUnitLinkNodeIdX if known, otherwise 16 octets of binary 0." -- AGENTCLAUSE -- " -- CLASS-COMMAND: You can write a small description -- CLASS-NAME: com.mcdata.console.snmp.mib.emc.EmcUnitLinkTable -- INSTANTIATE: at-start" -- END AGENTCLAUSE ::= { fcConnUnitLinkEntry 4 } fcConnUnitLinkNodeIdY OBJECT-TYPE SYNTAX OCTET STRING (SIZE(64)) MAX-ACCESS read-only STATUS current DESCRIPTION "The node WWN of the unit at the other end of the link. If the node WWN is unknown and the node is an fcConnUnit in the responding agent, then the value of this object MUST be equal to its fcConnUnitId." -- AGENTCLAUSE -- " -- CLASS-COMMAND: You can write a small description -- CLASS-NAME: com.mcdata.console.snmp.mib.emc.EmcUnitLinkTable -- INSTANTIATE: at-start" -- END AGENTCLAUSE ::= { fcConnUnitLinkEntry 5 } fcConnUnitLinkPortNumberY OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The port number on the unit specified by fcConnUnitLinkNodeIdY if known, otherwise -1. If the value is non-negative then it will be equal to fcConnUnitPortPhysicalNumber." -- AGENTCLAUSE -- " -- CLASS-COMMAND: You can write a small description -- CLASS-NAME: com.mcdata.console.snmp.mib.emc.EmcUnitLinkTable -- INSTANTIATE: at-start" -- END AGENTCLAUSE ::= { fcConnUnitLinkEntry 6 } fcConnUnitLinkPortWwnY OBJECT-TYPE SYNTAX OCTET STRING (SIZE(16)) MAX-ACCESS read-only STATUS current DESCRIPTION "The port WWN on the unit specified by fcConnUnitLinkNodeIdY if known, otherwise 16 octets of binary 0." -- AGENTCLAUSE -- " -- CLASS-COMMAND: You can write a small description -- CLASS-NAME: com.mcdata.console.snmp.mib.emc.EmcUnitLinkTable -- INSTANTIATE: at-start" -- END AGENTCLAUSE ::= { fcConnUnitLinkEntry 7 } fcConnUnitLinkAgentAddressY OBJECT-TYPE SYNTAX OCTET STRING (SIZE(16)) MAX-ACCESS read-only STATUS current DESCRIPTION "The address of an FCMGMT MIB agent for the node identified by fcConnUnitLinkNodeIdY, if known; otherwise 16 octets of binary 0." -- AGENTCLAUSE -- " -- CLASS-COMMAND: You can write a small description -- CLASS-NAME: com.mcdata.console.snmp.mib.emc.EmcUnitLinkTable -- INSTANTIATE: at-start" -- END AGENTCLAUSE ::= { fcConnUnitLinkEntry 8 } fcConnUnitLinkAgentAddressTypeY OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "If fcConnUnitLinkAgentAddressY is non-zero, then it is a protocol address. fcConnUnitLinkAgentAddressTypeY is the the 'address family number' assigned by IANA to identify the address format (eg, 1 is Ipv4, 2 is Ipv6)." -- AGENTCLAUSE -- " -- CLASS-COMMAND: You can write a small description -- CLASS-NAME: com.mcdata.console.snmp.mib.emc.EmcUnitLinkTable -- INSTANTIATE: at-start" -- END AGENTCLAUSE ::= { fcConnUnitLinkEntry 9 } fcConnUnitLinkAgentPortY OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "The IP port number for the agent. This is provided in case the agent is at a non-standard SNMP port." -- AGENTCLAUSE -- " -- CLASS-COMMAND: You can write a small description -- CLASS-NAME: com.mcdata.console.snmp.mib.emc.EmcUnitLinkTable -- INSTANTIATE: at-start" -- END AGENTCLAUSE ::= { fcConnUnitLinkEntry 10 } fcConnUnitLinkUnitTypeY OBJECT-TYPE SYNTAX FcUnitType MAX-ACCESS read-only STATUS current DESCRIPTION "Type of the FC connectivity unit as defined in fcConnUnitType." -- AGENTCLAUSE -- " -- CLASS-COMMAND: You can write a small description -- CLASS-NAME: com.mcdata.console.snmp.mib.emc.EmcUnitLinkTable -- INSTANTIATE: at-start" -- END AGENTCLAUSE ::= { fcConnUnitLinkEntry 11 } fcConnUnitLinkConnIdY OBJECT-TYPE SYNTAX OCTET STRING (SIZE(3)) MAX-ACCESS read-only STATUS current DESCRIPTION "This is the Fibre Channel ID of this port. If the connectivity unit is a switch, this is expected to be a 24-bit Big Endian value. If this is loop, then it is the ALPA that is connected. If this is an e-port, then it will only contain the domain ID. If not any of those, unknown or cascaded loop, return all bits set to 1." -- AGENTCLAUSE -- " -- CLASS-COMMAND: You can write a small description -- CLASS-NAME: com.mcdata.console.snmp.mib.emc.EmcUnitLinkTable -- INSTANTIATE: at-start" -- END AGENTCLAUSE ::= { fcConnUnitLinkEntry 12 } -- There is one and only one statistics table for each -- individual port. For all objects in statistics table, -- if the object is not supported by the conn unit then -- the high order bit is set to 1 with all other bits set -- to zero. The high order bit is reserved to indicate if -- the object if supported or not. All objects start at -- a value of zero at hardware initialization and continue -- incrementing till end of 63 bits and then wrap to zero. -- Port Statistics fcConnUnitPortStatTable OBJECT-TYPE SYNTAX SEQUENCE OF FcConnUnitPortStatEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A list of statistics for the ports." ::= { fcMgmtStatistics 1 } fcConnUnitPortStatEntry OBJECT-TYPE SYNTAX FcConnUnitPortStatEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry describing port statistics." INDEX { fcConnUnitId, fcConnUnitPortStatIndex } ::= { fcConnUnitPortStatTable 1 } FcConnUnitPortStatEntry ::= SEQUENCE { fcConnUnitPortStatIndex Unsigned32, fcConnUnitPortStatErrs Counter64, fcConnUnitPortStatTxObjects Counter64, fcConnUnitPortStatRxObjects Counter64, fcConnUnitPortStatTxElements Counter64, fcConnUnitPortStatRxElements Counter64, fcConnUnitPortStatBBCreditZero Counter64, fcConnUnitPortStatInputBuffsFull Counter64, fcConnUnitPortStatFBSYFrames Counter64, fcConnUnitPortStatPBSYFrames Counter64, fcConnUnitPortStatFRJTFrames Counter64, fcConnUnitPortStatPRJTFrames Counter64, fcConnUnitPortStatC1RxFrames Counter64, fcConnUnitPortStatC1TxFrames Counter64, fcConnUnitPortStatC1FBSYFrames Counter64, fcConnUnitPortStatC1PBSYFrames Counter64, fcConnUnitPortStatC1FRJTFrames Counter64, fcConnUnitPortStatC1PRJTFrames Counter64, fcConnUnitPortStatC2RxFrames Counter64, fcConnUnitPortStatC2TxFrames Counter64, fcConnUnitPortStatC2FBSYFrames Counter64, fcConnUnitPortStatC2PBSYFrames Counter64, fcConnUnitPortStatC2FRJTFrames Counter64, fcConnUnitPortStatC2PRJTFrames Counter64, fcConnUnitPortStatC3RxFrames Counter64, fcConnUnitPortStatC3TxFrames Counter64, fcConnUnitPortStatC3Discards Counter64, fcConnUnitPortStatRxMcastObjects Counter64, fcConnUnitPortStatTxMcastObjects Counter64, fcConnUnitPortStatRxBcastObjects Counter64, fcConnUnitPortStatTxBcastObjects Counter64, fcConnUnitPortStatRxLinkResets Counter64, fcConnUnitPortStatTxLinkResets Counter64, fcConnUnitPortStatLinkResets Counter64, fcConnUnitPortStatRxOfflineSeqs Counter64, fcConnUnitPortStatTxOfflineSeqs Counter64, fcConnUnitPortStatOfflineSeqs Counter64, fcConnUnitPortStatLinkFailures Counter64, fcConnUnitPortStatInvalidCRC Counter64, fcConnUnitPortStatInvalidTxWords Counter64, fcConnUnitPortStatPSPErrs Counter64, fcConnUnitPortStatLossOfSignal Counter64, fcConnUnitPortStatLossOfSync Counter64, fcConnUnitPortStatInvOrderedSets Counter64, fcConnUnitPortStatFramesTooLong Counter64, fcConnUnitPortStatFramesTooShort Counter64, fcConnUnitPortStatAddressErrs Counter64, fcConnUnitPortStatDelimiterErrs Counter64, fcConnUnitPortStatEncodingErrs Counter64 } fcConnUnitPortStatIndex OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "A unique value among all entrys in this table, between 0 and fcConnUnitNumPort[fcConnUnitPortUnitId]." -- AGENTCLAUSE -- " -- CLASS-COMMAND: You can write a small description -- CLASS-NAME: com.mcdata.console.snmp.mib.emc.EmcUnitPortStatTable -- INSTANTIATE: at-start" -- END AGENTCLAUSE ::= { fcConnUnitPortStatEntry 1 } fcConnUnitPortStatErrs OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "A count of the errors that have occured on this port." -- AGENTCLAUSE -- " -- CLASS-COMMAND: You can write a small description -- CLASS-NAME: com.mcdata.console.snmp.mib.emc.EmcUnitPortStatTable -- INSTANTIATE: at-start" -- END AGENTCLAUSE ::= { fcConnUnitPortStatEntry 2 } fcConnUnitPortStatTxObjects OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of frames/packets/IOs/etc that have been transmitted by this port. Note: A Fibre Channel frame starts with SOF and ends with EOF. FC loop devices should not count frames passed through. This value represents the sum total for all other Tx objects." -- AGENTCLAUSE -- " -- CLASS-COMMAND: You can write a small description -- CLASS-NAME: com.mcdata.console.snmp.mib.emc.EmcUnitPortStatTable -- INSTANTIATE: at-start" -- END AGENTCLAUSE ::= { fcConnUnitPortStatEntry 3 } fcConnUnitPortStatRxObjects OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of frames/packets/IOs/etc that have been received by this port. Note: A Fibre Channel frame starts with SOF and ends with EOF. FC loop devices should not count frames passed through. This value represents the sum total for all other Rx objects." -- AGENTCLAUSE -- " -- CLASS-COMMAND: You can write a small description -- CLASS-NAME: com.mcdata.console.snmp.mib.emc.EmcUnitPortStatTable -- INSTANTIATE: at-start" -- END AGENTCLAUSE ::= { fcConnUnitPortStatEntry 4 } fcConnUnitPortStatTxElements OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of octets or bytes that have been transmitted by this port. One second periodic polling of the port. This value is saved and compared with the next polled value to compute net throughput. Note, for Fibre Channel, ordered sets are not included in the count." -- AGENTCLAUSE -- " -- CLASS-COMMAND: You can write a small description -- CLASS-NAME: com.mcdata.console.snmp.mib.emc.EmcUnitPortStatTable -- INSTANTIATE: at-start" -- END AGENTCLAUSE ::= { fcConnUnitPortStatEntry 5 } fcConnUnitPortStatRxElements OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of octets or bytes that have been received by this port. One second periodic polling of the port. This value is saved and compared with the next polled value to compute net throughput. Note, for Fibre Channel, ordered sets are not included in the count." -- AGENTCLAUSE -- " -- CLASS-COMMAND: You can write a small description -- CLASS-NAME: com.mcdata.console.snmp.mib.emc.EmcUnitPortStatTable -- INSTANTIATE: at-start" -- END AGENTCLAUSE ::= { fcConnUnitPortStatEntry 6 } fcConnUnitPortStatBBCreditZero OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "Count of transitions in/out of BBcredit zero state. The other side is not providing any credit. Note, this is a Fibre Channel stat only." -- AGENTCLAUSE -- " -- CLASS-COMMAND: You can write a small description -- CLASS-NAME: com.mcdata.console.snmp.mib.emc.EmcUnitPortStatTable -- INSTANTIATE: at-start" -- END AGENTCLAUSE ::= { fcConnUnitPortStatEntry 7 } fcConnUnitPortStatInputBuffsFull OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "Count of occurrences when all input buffers of a port were full and outbound buffer-to-buffer credit transitioned to zero. There is no credit to provide to other side. Note, this is a Fibre Channel stat only." -- AGENTCLAUSE -- " -- CLASS-COMMAND: You can write a small description -- CLASS-NAME: com.mcdata.console.snmp.mib.emc.EmcUnitPortStatTable -- INSTANTIATE: at-start" -- END AGENTCLAUSE ::= { fcConnUnitPortStatEntry 8 } fcConnUnitPortStatFBSYFrames OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "Count of times that FBSY was returned to this port as a result of a frame that could not be delivered to the other end of the link. This occurs if either the Fabric or the destination port is temporarily busy. Port can only occur on SOFc1 frames (the frames that establish a connection). Note, this is a Fibre Channel only stat. This is the sum of all classes. If you cannot keep the by class counters, then keep the sum counters." -- AGENTCLAUSE -- " -- CLASS-COMMAND: You can write a small description -- CLASS-NAME: com.mcdata.console.snmp.mib.emc.EmcUnitPortStatTable -- INSTANTIATE: at-start" -- END AGENTCLAUSE ::= { fcConnUnitPortStatEntry 9 } fcConnUnitPortStatPBSYFrames OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "Count of times that PBSY was returned to this port as a result of a frame that could not be delivered to the other end of the link. This occurs if the destination port is temporarily busy. PBSY can only occur on SOFc1 frames (the frames that establish a connection). Note, this is a Fibre Channel only stat.This is the sum of all classes. If you cannot keep the by class counters, then keep the sum counters." -- AGENTCLAUSE -- " -- CLASS-COMMAND: You can write a small description -- CLASS-NAME: com.mcdata.console.snmp.mib.emc.EmcUnitPortStatTable -- INSTANTIATE: at-start" -- END AGENTCLAUSE ::= { fcConnUnitPortStatEntry 10 } fcConnUnitPortStatFRJTFrames OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "Count of times that FRJT was returned to this port as a result of a Frame that was rejected by the fabric. Note, this is the total for all classes and is a Fibre Channel only stat." -- AGENTCLAUSE -- " -- CLASS-COMMAND: You can write a small description -- CLASS-NAME: com.mcdata.console.snmp.mib.emc.EmcUnitPortStatTable -- INSTANTIATE: at-start" -- END AGENTCLAUSE ::= { fcConnUnitPortStatEntry 11 } fcConnUnitPortStatPRJTFrames OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "Count of times that FRJT was returned to this port as a result of a Frame that was rejected at the destination N_Port. Note, this is the total for all classes and is a Fibre Channel only stat." -- AGENTCLAUSE -- " -- CLASS-COMMAND: You can write a small description -- CLASS-NAME: com.mcdata.console.snmp.mib.emc.EmcUnitPortStatTable -- INSTANTIATE: at-start" -- END AGENTCLAUSE ::= { fcConnUnitPortStatEntry 12 } fcConnUnitPortStatC1RxFrames OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "Count of Class 1 Frames received at this port. Note, this is a Fibre Channel only stat." -- AGENTCLAUSE -- " -- CLASS-COMMAND: You can write a small description -- CLASS-NAME: com.mcdata.console.snmp.mib.emc.EmcUnitPortStatTable -- INSTANTIATE: at-start" -- END AGENTCLAUSE ::= { fcConnUnitPortStatEntry 13 } fcConnUnitPortStatC1TxFrames OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "Count of Class 1 Frames transmitted out this port. Note, this is a Fibre Channel only stat." -- AGENTCLAUSE -- " -- CLASS-COMMAND: You can write a small description -- CLASS-NAME: com.mcdata.console.snmp.mib.emc.EmcUnitPortStatTable -- INSTANTIATE: at-start" -- END AGENTCLAUSE ::= { fcConnUnitPortStatEntry 14 } fcConnUnitPortStatC1FBSYFrames OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "Count of times that FBSY was returned to this port as a result of a Class 1 Frame that could not be delivered to the other end of the link. This occurs if either the Fabric or the destination port is temporarily busy. FBSY can only occur on SOFc1 frames (the frames that establish a connection). Note, this is a Fibre Channel only stat." -- AGENTCLAUSE -- " -- CLASS-COMMAND: You can write a small description -- CLASS-NAME: com.mcdata.console.snmp.mib.emc.EmcUnitPortStatTable -- INSTANTIATE: at-start" -- END AGENTCLAUSE ::= { fcConnUnitPortStatEntry 15 } fcConnUnitPortStatC1PBSYFrames OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "Count of times that PBSY was returned to this port as a result of a Class 1 Frame that could not be delivered to the other end of the link. This occurs if the destination N_Port is temporarily busy. PBSY can only occur on SOFc1 frames (the frames that establish a connection). Note, this is a Fibre Channel only stat." -- AGENTCLAUSE -- " -- CLASS-COMMAND: You can write a small description -- CLASS-NAME: com.mcdata.console.snmp.mib.emc.EmcUnitPortStatTable -- INSTANTIATE: at-start" -- END AGENTCLAUSE ::= { fcConnUnitPortStatEntry 16 } fcConnUnitPortStatC1FRJTFrames OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "Count of times that FRJT was returned to this port as a result of a Class 1 Frame that was rejected by the fabric. Note, this is a Fibre Channel only stat." -- AGENTCLAUSE -- " -- CLASS-COMMAND: You can write a small description -- CLASS-NAME: com.mcdata.console.snmp.mib.emc.EmcUnitPortStatTable -- INSTANTIATE: at-start" -- END AGENTCLAUSE ::= { fcConnUnitPortStatEntry 17 } fcConnUnitPortStatC1PRJTFrames OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "Count of times that FRJT was returned to this port as a result of a Class 1 Frame that was rejected at the destination N_Port. Note, this is a Fibre Channel only stat." -- AGENTCLAUSE -- " -- CLASS-COMMAND: You can write a small description -- CLASS-NAME: com.mcdata.console.snmp.mib.emc.EmcUnitPortStatTable -- INSTANTIATE: at-start" -- END AGENTCLAUSE ::= { fcConnUnitPortStatEntry 18 } fcConnUnitPortStatC2RxFrames OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "Count of Class 2 Frames received at this port. Note, this is a Fibre Channel only stat." -- AGENTCLAUSE -- " -- CLASS-COMMAND: You can write a small description -- CLASS-NAME: com.mcdata.console.snmp.mib.emc.EmcUnitPortStatTable -- INSTANTIATE: at-start" -- END AGENTCLAUSE ::= { fcConnUnitPortStatEntry 19 } fcConnUnitPortStatC2TxFrames OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "Count of Class 2 Frames transmitted out this port. Note, this is a Fibre Channel only stat." -- AGENTCLAUSE -- " -- CLASS-COMMAND: You can write a small description -- CLASS-NAME: com.mcdata.console.snmp.mib.emc.EmcUnitPortStatTable -- INSTANTIATE: at-start" -- END AGENTCLAUSE ::= { fcConnUnitPortStatEntry 20 } fcConnUnitPortStatC2FBSYFrames OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "Count of times that FBSY was returned to this port as a result of a Class 2 Frame that could not be delivered to the other end of the link. This occurs if either the Fabric or the destination port is temporarily busy. FBSY can only occur on SOFc1 frames (the frames that establish a connection). Note, this is a Fibre Channel only stat." -- AGENTCLAUSE -- " -- CLASS-COMMAND: You can write a small description -- CLASS-NAME: com.mcdata.console.snmp.mib.emc.EmcUnitPortStatTable -- INSTANTIATE: at-start" -- END AGENTCLAUSE ::= { fcConnUnitPortStatEntry 21 } fcConnUnitPortStatC2PBSYFrames OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "Count of times that PBSY was returned to this port as a result of a Class 2 Frame that could not be delivered to the other end of the link. This occurs if the destination N_Port is temporarily busy. PBSY can only occur on SOFc1 frames (the frames that establish a connection). Note, this is a Fibre Channel only stat." -- AGENTCLAUSE -- " -- CLASS-COMMAND: You can write a small description -- CLASS-NAME: com.mcdata.console.snmp.mib.emc.EmcUnitPortStatTable -- INSTANTIATE: at-start" -- END AGENTCLAUSE ::= { fcConnUnitPortStatEntry 22 } fcConnUnitPortStatC2FRJTFrames OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "Count of times that FRJT was returned to this port as a result of a Class 2 Frame that was rejected by the fabric. Note, this is a Fibre Channel only stat." -- AGENTCLAUSE -- " -- CLASS-COMMAND: You can write a small description -- CLASS-NAME: com.mcdata.console.snmp.mib.emc.EmcUnitPortStatTable -- INSTANTIATE: at-start" -- END AGENTCLAUSE ::= { fcConnUnitPortStatEntry 23 } fcConnUnitPortStatC2PRJTFrames OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "Count of times that FRJT was returned to this port as a result of a Class 2 Frame that was rejected at the destination N_Port. Note, this is a Fibre Channel only stat." -- AGENTCLAUSE -- " -- CLASS-COMMAND: You can write a small description -- CLASS-NAME: com.mcdata.console.snmp.mib.emc.EmcUnitPortStatTable -- INSTANTIATE: at-start" -- END AGENTCLAUSE ::= { fcConnUnitPortStatEntry 24 } fcConnUnitPortStatC3RxFrames OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "Count of Class 3 Frames received at this port. Note, this is a Fibre Channel only stat." -- AGENTCLAUSE -- " -- CLASS-COMMAND: You can write a small description -- CLASS-NAME: com.mcdata.console.snmp.mib.emc.EmcUnitPortStatTable -- INSTANTIATE: at-start" -- END AGENTCLAUSE ::= { fcConnUnitPortStatEntry 25 } fcConnUnitPortStatC3TxFrames OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "Count of Class 3 Frames transmitted out of this port. Note, this is a Fibre Channel only stat." -- AGENTCLAUSE -- " -- CLASS-COMMAND: You can write a small description -- CLASS-NAME: com.mcdata.console.snmp.mib.emc.EmcUnitPortStatTable -- INSTANTIATE: at-start" -- END AGENTCLAUSE ::= { fcConnUnitPortStatEntry 26 } fcConnUnitPortStatC3Discards OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "Count of Class 3 Frames that were discarded upon reception at this port. There is no FBSY or FRJT generated for Class 3 Frames. They are simply discarded if they cannot be delivered. Note, this is a Fibre Channel only stat." -- AGENTCLAUSE -- " -- CLASS-COMMAND: You can write a small description -- CLASS-NAME: com.mcdata.console.snmp.mib.emc.EmcUnitPortStatTable -- INSTANTIATE: at-start" -- END AGENTCLAUSE ::= { fcConnUnitPortStatEntry 27 } fcConnUnitPortStatRxMcastObjects OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "Count of Multicast Frames or Packets received at this port." -- AGENTCLAUSE -- " -- CLASS-COMMAND: You can write a small description -- CLASS-NAME: com.mcdata.console.snmp.mib.emc.EmcUnitPortStatTable -- INSTANTIATE: at-start" -- END AGENTCLAUSE ::= { fcConnUnitPortStatEntry 28 } fcConnUnitPortStatTxMcastObjects OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "Count of Multicast Frames or Packets transmitted out this port." -- AGENTCLAUSE -- " -- CLASS-COMMAND: You can write a small description -- CLASS-NAME: com.mcdata.console.snmp.mib.emc.EmcUnitPortStatTable -- INSTANTIATE: at-start" -- END AGENTCLAUSE ::= { fcConnUnitPortStatEntry 29 } fcConnUnitPortStatRxBcastObjects OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "Count of Broadcast Frames or Packets received at this port." -- AGENTCLAUSE -- " -- CLASS-COMMAND: You can write a small description -- CLASS-NAME: com.mcdata.console.snmp.mib.emc.EmcUnitPortStatTable -- INSTANTIATE: at-start" -- END AGENTCLAUSE ::= { fcConnUnitPortStatEntry 30 } fcConnUnitPortStatTxBcastObjects OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "Count of Broadcast Frames or Packets transmitted out this port. On a Fibre Channel loop, count only OPNr frames generated." -- AGENTCLAUSE -- " -- CLASS-COMMAND: You can write a small description -- CLASS-NAME: com.mcdata.console.snmp.mib.emc.EmcUnitPortStatTable -- INSTANTIATE: at-start" -- END AGENTCLAUSE ::= { fcConnUnitPortStatEntry 31 } fcConnUnitPortStatRxLinkResets OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "Count of Link resets. This is the number of LRs received. Note, this is a Fibre Channel only stat." -- AGENTCLAUSE -- " -- CLASS-COMMAND: You can write a small description -- CLASS-NAME: com.mcdata.console.snmp.mib.emc.EmcUnitPortStatTable -- INSTANTIATE: at-start" -- END AGENTCLAUSE ::= { fcConnUnitPortStatEntry 32 } fcConnUnitPortStatTxLinkResets OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "Count of Link resets. This is the number LRs transmitted. Note, this is a Fibre Channel only stat." -- AGENTCLAUSE -- " -- CLASS-COMMAND: You can write a small description -- CLASS-NAME: com.mcdata.console.snmp.mib.emc.EmcUnitPortStatTable -- INSTANTIATE: at-start" -- END AGENTCLAUSE ::= { fcConnUnitPortStatEntry 33 } fcConnUnitPortStatLinkResets OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "Count of Link resets and LIPs detected at this port. The number times the reset link protocol is initiated. These are the count of the logical resets, a count of the number of primatives. Note, this is a Fibre Channel only stat." -- AGENTCLAUSE -- " -- CLASS-COMMAND: You can write a small description -- CLASS-NAME: com.mcdata.console.snmp.mib.emc.EmcUnitPortStatTable -- INSTANTIATE: at-start" -- END AGENTCLAUSE ::= { fcConnUnitPortStatEntry 34 } fcConnUnitPortStatRxOfflineSeqs OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "Count of Offline Primitive OLS received at this port. Note, this is a Fibre Channel only stat." -- AGENTCLAUSE -- " -- CLASS-COMMAND: You can write a small description -- CLASS-NAME: com.mcdata.console.snmp.mib.emc.EmcUnitPortStatTable -- INSTANTIATE: at-start" -- END AGENTCLAUSE ::= { fcConnUnitPortStatEntry 35 } fcConnUnitPortStatTxOfflineSeqs OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "Count of Offline Primitive OLS transmitted by this port. Note, this is a Fibre Channel only stat." -- AGENTCLAUSE -- " -- CLASS-COMMAND: You can write a small description -- CLASS-NAME: com.mcdata.console.snmp.mib.emc.EmcUnitPortStatTable -- INSTANTIATE: at-start" -- END AGENTCLAUSE ::= { fcConnUnitPortStatEntry 36 } fcConnUnitPortStatOfflineSeqs OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "Count of Offline Primitive sequence received at this port. Note, this is a Fibre Channel only stat." -- AGENTCLAUSE -- " -- CLASS-COMMAND: You can write a small description -- CLASS-NAME: com.mcdata.console.snmp.mib.emc.EmcUnitPortStatTable -- INSTANTIATE: at-start" -- END AGENTCLAUSE ::= { fcConnUnitPortStatEntry 37 } fcConnUnitPortStatLinkFailures OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "Count of link failures. This count is part of the Link Error Status Block (LESB). (FC-PH 29.8). Note, this is a Fibre Channel only stat." -- AGENTCLAUSE -- " -- CLASS-COMMAND: You can write a small description -- CLASS-NAME: com.mcdata.console.snmp.mib.emc.EmcUnitPortStatTable -- INSTANTIATE: at-start" -- END AGENTCLAUSE ::= { fcConnUnitPortStatEntry 38 } fcConnUnitPortStatInvalidCRC OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "Count of frames received with invalid CRC. This count is part of the Link Error Status Block (LESB). (FC-PH 29.8). Loop ports should not count CRC errors passing through when monitoring. Note, this is a Fibre Channel only stat." -- AGENTCLAUSE -- " -- CLASS-COMMAND: You can write a small description -- CLASS-NAME: com.mcdata.console.snmp.mib.emc.EmcUnitPortStatTable -- INSTANTIATE: at-start" -- END AGENTCLAUSE ::= { fcConnUnitPortStatEntry 39 } fcConnUnitPortStatInvalidTxWords OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "Count of invalid transmission words received at this port. This count is part of the Link Error Status Block (LESB). (FC-PH 29.8). Note, this is a Fibre Channel only stat." -- AGENTCLAUSE -- " -- CLASS-COMMAND: You can write a small description -- CLASS-NAME: com.mcdata.console.snmp.mib.emc.EmcUnitPortStatTable -- INSTANTIATE: at-start" -- END AGENTCLAUSE ::= { fcConnUnitPortStatEntry 40 } fcConnUnitPortStatPSPErrs OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "Count of primitive sequence protocol (PSP) errors detected at this port. This count is part of the Link Error Status Block (LESB) FC-PH 29.8). Note, this is a Fibre Channel only stat." -- AGENTCLAUSE -- " -- CLASS-COMMAND: You can write a small description -- CLASS-NAME: com.mcdata.console.snmp.mib.emc.EmcUnitPortStatTable -- INSTANTIATE: at-start" -- END AGENTCLAUSE ::= { fcConnUnitPortStatEntry 41 } fcConnUnitPortStatLossOfSignal OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "Count of instances of signal loss detected at port. This count is part of the Link Error Status Block (LESB). (FC-PH 29.8). Note, this is a Fibre Channel only stat." -- AGENTCLAUSE -- " -- CLASS-COMMAND: You can write a small description -- CLASS-NAME: com.mcdata.console.snmp.mib.emc.EmcUnitPortStatTable -- INSTANTIATE: at-start" -- END AGENTCLAUSE ::= { fcConnUnitPortStatEntry 42 } fcConnUnitPortStatLossOfSync OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "Count of instances of synchronization loss detected at port. This count is part of the Link Error Status Block (LESB). (FC-PH 29.8). Note, this is a Fibre Channel only stat." -- AGENTCLAUSE -- " -- CLASS-COMMAND: You can write a small description -- CLASS-NAME: com.mcdata.console.snmp.mib.emc.EmcUnitPortStatTable -- INSTANTIATE: at-start" -- END AGENTCLAUSE ::= { fcConnUnitPortStatEntry 43 } fcConnUnitPortStatInvOrderedSets OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "Count of invalid ordered sets received at port. This count is part of the Link Error Status Block (LESB). (FC-PH 29.8). Note, this is a Fibre Channel only stat." -- AGENTCLAUSE -- " -- CLASS-COMMAND: You can write a small description -- CLASS-NAME: com.mcdata.console.snmp.mib.emc.EmcUnitPortStatTable -- INSTANTIATE: at-start" -- END AGENTCLAUSE ::= { fcConnUnitPortStatEntry 44 } fcConnUnitPortStatFramesTooLong OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "Count of frames received at this port where the frame length was greater than what was agreed to in FLOGI/PLOGI. This could be caused by losing the end of frame delimiter. Note, this is a Fibre Channel only stat." -- AGENTCLAUSE -- " -- CLASS-COMMAND: You can write a small description -- CLASS-NAME: com.mcdata.console.snmp.mib.emc.EmcUnitPortStatTable -- INSTANTIATE: at-start" -- END AGENTCLAUSE ::= { fcConnUnitPortStatEntry 45 } fcConnUnitPortStatFramesTooShort OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "Count of frames received at this port where the frame length was less than the minimum indicated by the frame header - normally 24 bytes, but it could be more if the DFCTL field indicates an optional header should have been present. Note, this is a Fibre Channel only stat." -- AGENTCLAUSE -- " -- CLASS-COMMAND: You can write a small description -- CLASS-NAME: com.mcdata.console.snmp.mib.emc.EmcUnitPortStatTable -- INSTANTIATE: at-start" -- END AGENTCLAUSE ::= { fcConnUnitPortStatEntry 46 } fcConnUnitPortStatAddressErrs OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "Count of frames received with unknown addressing. e.g. unknown SID or DID. The SID or DID is not known to the routing algorithm. Note, this is a Fibre Channel only stat." -- AGENTCLAUSE -- " -- CLASS-COMMAND: You can write a small description -- CLASS-NAME: com.mcdata.console.snmp.mib.emc.EmcUnitPortStatTable -- INSTANTIATE: at-start" -- END AGENTCLAUSE ::= { fcConnUnitPortStatEntry 47 } fcConnUnitPortStatDelimiterErrs OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "Count of invalid frame delimiters received at this port. An example is a frame with a class 2 start and and a class 3 at the end. Note, this is a Fibre Channel only stat." -- AGENTCLAUSE -- " -- CLASS-COMMAND: You can write a small description -- CLASS-NAME: com.mcdata.console.snmp.mib.emc.EmcUnitPortStatTable -- INSTANTIATE: at-start" -- END AGENTCLAUSE ::= { fcConnUnitPortStatEntry 48 } fcConnUnitPortStatEncodingErrs OBJECT-TYPE SYNTAX Counter64 MAX-ACCESS read-only STATUS current DESCRIPTION "Count of disparity errors received at this port. Note, this is a Fibre Channel only stat." -- AGENTCLAUSE -- " -- CLASS-COMMAND: You can write a small description -- CLASS-NAME: com.mcdata.console.snmp.mib.emc.EmcUnitPortStatTable -- INSTANTIATE: at-start" -- END AGENTCLAUSE ::= { fcConnUnitPortStatEntry 49 } -- -- the Fibre Channel Simple Name Server table -- -- The Fibre Channel Simple Name Server table contains an entry -- for each device presently known to this fcConnUnit. There will -- not be any version on this since FC-GS3 does not define a -- version today. -- -- This table is accessed either directly if the management -- software has an index value or via GetNexts. The value of -- the indexes are not required to be contiguous. Each entry -- created in this table will be assigned an index. This -- relationship is kept persistent until the entry is removed -- from the table or the system is reset. The total number of -- entries are defined by the size of the table fcConnUnitSnsMaxRows OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The maximum number of rows in the fcConnUnitSnsTable table." -- AGENTCLAUSE -- " -- CLASS-COMMAND: -- CLASS-NAME: com.mcdata.console.snmp.mib.emc.EmcGetSnsMaxEntry -- INSTANTIATE: each-time" -- END AGENTCLAUSE ::= { fcMgmtConfig 9 } fcConnUnitSnsTable OBJECT-TYPE SYNTAX SEQUENCE OF FcConnUnitSnsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This table contains an entry for each object registered with this port in the switch." ::= { fcMgmtSNS 1 } fcConnUnitSnsEntry OBJECT-TYPE SYNTAX FcConnUnitSnsEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The Simple Name Server table for the port represented by fcConnUnitSnsPortIndex ." INDEX { fcConnUnitId, fcConnUnitSnsPortIndex, fcConnUnitSnsPortIdentifier } ::= { fcConnUnitSnsTable 1 } FcConnUnitSnsEntry ::= SEQUENCE { fcConnUnitSnsPortIndex Counter32, fcConnUnitSnsPortIdentifier FcGlobalId, -- was FcAddressId (undefined) fcConnUnitSnsPortName FcNameId, fcConnUnitSnsNodeName FcNameId, fcConnUnitSnsClassOfSvc OCTET STRING, fcConnUnitSnsNodeIPAddress OCTET STRING, fcConnUnitSnsProcAssoc OCTET STRING, fcConnUnitSnsFC4Type OCTET STRING, fcConnUnitSnsPortType OCTET STRING, fcConnUnitSnsPortIPAddress OCTET STRING, fcConnUnitSnsFabricPortName FcNameId, fcConnUnitSnsHardAddress FcGlobalId, -- was FcAddressId (undefined) fcConnUnitSnsSymbolicPortName DisplayString, fcConnUnitSnsSymbolicNodeName DisplayString } fcConnUnitSnsPortIndex OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The physical port number of this SNS table entry. Each physical port has an SNS table with 1-n entries indexed by ConnUnitSnsPortIdentifier (port address)" -- AGENTCLAUSE -- " -- CLASS-COMMAND: You can write a small description -- CLASS-NAME: com.mcdata.console.snmp.mib.emc.EmcUnitNameServerTable -- INSTANTIATE: at-start" -- END AGENTCLAUSE ::= { fcConnUnitSnsEntry 1 } fcConnUnitSnsPortIdentifier OBJECT-TYPE SYNTAX FcGlobalId -- was FcAddressId (undefined) MAX-ACCESS read-only STATUS current DESCRIPTION "The Port Identifier for this entry in the SNS table." -- AGENTCLAUSE -- " -- CLASS-COMMAND: You can write a small description -- CLASS-NAME: com.mcdata.console.snmp.mib.emc.EmcUnitNameServerTable -- INSTANTIATE: at-start" -- END AGENTCLAUSE ::= { fcConnUnitSnsEntry 2 } fcConnUnitSnsPortName OBJECT-TYPE SYNTAX FcNameId MAX-ACCESS read-only STATUS current DESCRIPTION "The Port WWN for this entry in the SNS table." -- AGENTCLAUSE -- " -- CLASS-COMMAND: You can write a small description -- CLASS-NAME: com.mcdata.console.snmp.mib.emc.EmcUnitNameServerTable -- INSTANTIATE: at-start" -- END AGENTCLAUSE ::= { fcConnUnitSnsEntry 3 } fcConnUnitSnsNodeName OBJECT-TYPE SYNTAX FcNameId MAX-ACCESS read-only STATUS current DESCRIPTION "The Node Name for this entry in the SNS table." -- AGENTCLAUSE -- " -- CLASS-COMMAND: You can write a small description -- CLASS-NAME: com.mcdata.console.snmp.mib.emc.EmcUnitNameServerTable -- INSTANTIATE: at-start" -- END AGENTCLAUSE ::= { fcConnUnitSnsEntry 4 } fcConnUnitSnsClassOfSvc OBJECT-TYPE SYNTAX OCTET STRING (SIZE (1)) MAX-ACCESS read-only STATUS current DESCRIPTION "The Classes of Service offered by this entry in the SNS table." -- AGENTCLAUSE -- " -- CLASS-COMMAND: You can write a small description -- CLASS-NAME: com.mcdata.console.snmp.mib.emc.EmcUnitNameServerTable -- INSTANTIATE: at-start" -- END AGENTCLAUSE ::= { fcConnUnitSnsEntry 5 } fcConnUnitSnsNodeIPAddress OBJECT-TYPE SYNTAX OCTET STRING (SIZE(16)) MAX-ACCESS read-only STATUS current DESCRIPTION "The IPv6 formatted address of the Node for this entry in the SNS table." -- AGENTCLAUSE -- " -- CLASS-COMMAND: You can write a small description -- CLASS-NAME: com.mcdata.console.snmp.mib.emc.EmcUnitNameServerTable -- INSTANTIATE: at-start" -- END AGENTCLAUSE ::= { fcConnUnitSnsEntry 6 } fcConnUnitSnsProcAssoc OBJECT-TYPE SYNTAX OCTET STRING (SIZE (8)) MAX-ACCESS read-only STATUS current DESCRIPTION "The Process Associator for this entry in the SNS table." -- AGENTCLAUSE -- " -- CLASS-COMMAND: You can write a small description -- CLASS-NAME: com.mcdata.console.snmp.mib.emc.EmcUnitNameServerTable -- INSTANTIATE: at-start" -- END AGENTCLAUSE ::= { fcConnUnitSnsEntry 7 } fcConnUnitSnsFC4Type OBJECT-TYPE SYNTAX OCTET STRING (SIZE (32)) MAX-ACCESS read-only STATUS current DESCRIPTION "The FC-4 Types supported by this entry in the SNS table." -- AGENTCLAUSE -- " -- CLASS-COMMAND: You can write a small description -- CLASS-NAME: com.mcdata.console.snmp.mib.emc.EmcUnitNameServerTable -- INSTANTIATE: at-start" -- END AGENTCLAUSE ::= { fcConnUnitSnsEntry 8 } fcConnUnitSnsPortType OBJECT-TYPE SYNTAX OCTET STRING (SIZE (1)) MAX-ACCESS read-only STATUS current DESCRIPTION "The Port Type of this entry in the SNS table." -- AGENTCLAUSE -- " -- CLASS-COMMAND: You can write a small description -- CLASS-NAME: com.mcdata.console.snmp.mib.emc.EmcUnitNameServerTable -- INSTANTIATE: at-start" -- END AGENTCLAUSE ::= { fcConnUnitSnsEntry 9 } fcConnUnitSnsPortIPAddress OBJECT-TYPE SYNTAX OCTET STRING (SIZE(16)) MAX-ACCESS read-only STATUS current DESCRIPTION "The IPv6 formatted address of this entry in the SNS table." -- AGENTCLAUSE -- " -- CLASS-COMMAND: You can write a small description -- CLASS-NAME: com.mcdata.console.snmp.mib.emc.EmcUnitNameServerTable -- INSTANTIATE: at-start" -- END AGENTCLAUSE ::= { fcConnUnitSnsEntry 10 } fcConnUnitSnsFabricPortName OBJECT-TYPE SYNTAX FcNameId MAX-ACCESS read-only STATUS current DESCRIPTION "The Fabric Port name of this entry in the SNS table." -- AGENTCLAUSE -- " -- CLASS-COMMAND: You can write a small description -- CLASS-NAME: com.mcdata.console.snmp.mib.emc.EmcUnitNameServerTable -- INSTANTIATE: at-start" -- END AGENTCLAUSE ::= { fcConnUnitSnsEntry 11 } fcConnUnitSnsHardAddress OBJECT-TYPE SYNTAX FcGlobalId -- was FcAddressId (undefined) MAX-ACCESS read-only STATUS current DESCRIPTION "The Hard ALPA of this entry in the SNS table." -- AGENTCLAUSE -- " -- CLASS-COMMAND: You can write a small description -- CLASS-NAME: com.mcdata.console.snmp.mib.emc.EmcUnitNameServerTable -- INSTANTIATE: at-start" -- END AGENTCLAUSE ::= { fcConnUnitSnsEntry 12 } fcConnUnitSnsSymbolicPortName OBJECT-TYPE SYNTAX DisplayString (SIZE (0..79)) MAX-ACCESS read-only STATUS current DESCRIPTION "The Symbolic Port Name of this entry in the SNS table." -- AGENTCLAUSE -- " -- CLASS-COMMAND: You can write a small description -- CLASS-NAME: com.mcdata.console.snmp.mib.emc.EmcUnitNameServerTable -- INSTANTIATE: at-start" -- END AGENTCLAUSE ::= { fcConnUnitSnsEntry 13 } fcConnUnitSnsSymbolicNodeName OBJECT-TYPE SYNTAX DisplayString (SIZE (0..79)) MAX-ACCESS read-only STATUS current DESCRIPTION "The Symbolic Node Name of this entry in the SNS table." -- AGENTCLAUSE -- " -- CLASS-COMMAND: You can write a small description -- CLASS-NAME: com.mcdata.console.snmp.mib.emc.EmcUnitNameServerTable -- INSTANTIATE: at-start" -- END AGENTCLAUSE ::= { fcConnUnitSnsEntry 14 } -- -- SNMP trap registration group -- fcTrapMaxClients OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "The maximum number of SNMP trap recipients supported by the connectivity unit." -- AGENTCLAUSE -- " -- CLASS-COMMAND: You can write a small description -- CLASS-NAME: com.mcdata.console.snmp.mib.emc.EmcGetMaxTrapClients -- INSTANTIATE: each-time" -- END AGENTCLAUSE ::= { fcMgmtNotifyFilter 1 } fcTrapClientCount OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "The current number of rows in the trap table." -- AGENTCLAUSE -- " -- CLASS-COMMAND: You can write a small description -- CLASS-NAME: com.mcdata.console.snmp.mib.emc.EmcGetTrapClientCount -- INSTANTIATE: each-time" -- END AGENTCLAUSE ::= { fcMgmtNotifyFilter 2 } fcTrapRegTable OBJECT-TYPE SYNTAX SEQUENCE OF FcTrapRegEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A table containing a row for each IP address/port number that traps will be sent to." ::= { fcMgmtNotifyFilter 3 } fcTrapRegEntry OBJECT-TYPE SYNTAX FcTrapRegEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Ip/Port pair for a specific client." INDEX { fcTrapRegIpAddress, fcTrapRegPort } ::= { fcTrapRegTable 1 } FcTrapRegEntry ::= SEQUENCE { fcTrapRegIpAddress IpAddress, fcTrapRegPort Unsigned32, fcTrapRegFilter FcEventSeverity, fcTrapRegRowState RowStatus } fcTrapRegIpAddress OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-create STATUS current DESCRIPTION "The Ip address of a client registered for traps." -- AGENTCLAUSE -- " -- CLASS-COMMAND: You can write a small description -- CLASS-NAME: com.mcdata.console.snmp.mib.emc.EmcTrapRegTable -- INSTANTIATE: at-start" -- END AGENTCLAUSE ::= { fcTrapRegEntry 1 } fcTrapRegPort OBJECT-TYPE SYNTAX Unsigned32 (1..2147483647) MAX-ACCESS read-create STATUS current DESCRIPTION "The UDP port to send traps to for this host. Normally this would be the standard trap port (UDP/162)." -- AGENTCLAUSE -- " -- CLASS-COMMAND: You can write a small description -- CLASS-NAME: com.mcdata.console.snmp.mib.emc.EmcTrapRegTable -- INSTANTIATE: at-start" -- END AGENTCLAUSE ::= { fcTrapRegEntry 2 } fcTrapRegFilter OBJECT-TYPE SYNTAX FcEventSeverity MAX-ACCESS read-create STATUS current DESCRIPTION "This value defines the trap severity filter for this trap host. The fcConnUnit will send to the designated target entity traps that have a severity level less than or equal to this value." -- AGENTCLAUSE -- " -- CLASS-COMMAND: You can write a small description -- CLASS-NAME: com.mcdata.console.snmp.mib.emc.EmcTrapRegTable -- INSTANTIATE: at-start" -- END AGENTCLAUSE ::= { fcTrapRegEntry 3} fcTrapRegRowState OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "Specifies the operational status of the row. A RowStatus object may take any of six defined values: - active: traps may be sent as specified in this row; a management application may change the value of any objects in the row when the status is active. - notInService: traps will not be sent using this row. - notReady: the conceptual row exists in the agent, but is missing information necessary to send traps (i.e., if any of the other objects in the row are not present or contain invalid values); this value may not be supplied by a management application. - createAndGo: supplied by a management application wishing to create a new instance of a conceptual row, supplying valid values for the all the other objects in the row, and have its status automatically set to active, making it available for use in sending traps. - createAndWait: supplied by a management application wishing to create a new instance of a conceptual row but not make it available for use in sending traps at that time; and, - destroy: supplied by a management application wishing to delete an existing conceptual row." -- AGENTCLAUSE -- " -- CLASS-COMMAND: You can write a small description -- CLASS-NAME: com.mcdata.console.snmp.mib.emc.EmcTrapRegTable -- INSTANTIATE: at-start" -- END AGENTCLAUSE ::= { fcTrapRegEntry 4} -- -- Related traps -- fcConnUnitStatusChange NOTIFICATION-TYPE OBJECTS { fcConnUnitStatus, fcConnUnitState } STATUS current DESCRIPTION "The overall status of the connectivity unit has changed. Recommended severity level (for filtering): alert" ::= { fcMgmtNotifications 1 } fcConnUnitDeletedTrap NOTIFICATION-TYPE OBJECTS { fcConnUnitGlobalId } STATUS current DESCRIPTION "An fcConnUnit has been deleted from this agent. Recommended severity level (for filtering): warning" ::= { fcMgmtNotifications 2 } fcConnUnitEventTrap NOTIFICATION-TYPE OBJECTS { fcConnUnitGlobalId, fcConnUnitEventType, fcConnUnitEventObject, fcConnUnitEventDescr } STATUS current DESCRIPTION "An event has been generated by the connectivity unit. Recommended severity level (for filtering): info" ::= { fcMgmtNotifications 3 } fcConnUnitSensorStatusChange NOTIFICATION-TYPE OBJECTS { fcConnUnitSensorStatus } STATUS current DESCRIPTION "The overall status of the connectivity unit has changed. Recommended severity level (for filtering): alert" ::= { fcMgmtNotifications 4 } fcConnUnitPortStatusChange NOTIFICATION-TYPE OBJECTS { fcConnUnitPortStatus, fcConnUnitPortState } STATUS current DESCRIPTION "The overall status of the connectivity unit has changed. Recommended severity level (for filtering): alert" ::= { fcMgmtNotifications 5 } -- Conformance definitions -- (Repeated here from beginning of MIB for ease of reference below.) -- fcMgmtNotifications OBJECT IDENTIFIER ::= { fcMgmtMIB 0 } -- fcMgmtObjects OBJECT IDENTIFIER ::= { fcMgmtMIB 1 } -- fcMgmtConformance OBJECT IDENTIFIER ::= { fcMgmtMIB 2 } -- fcMgmtConfig OBJECT IDENTIFIER ::= { fcMgmtObjects 1 } -- fcMgmtNotifyFilter OBJECT IDENTIFIER ::= { fcMgmtObjects 2 } -- fcMgmtStatistics OBJECT IDENTIFIER ::= { fcMgmtObjects 3 } -- fcMgmtSNS OBJECT IDENTIFIER ::= { fcMgmtObjects 4 } -- fcMgmtCompliances OBJECT IDENTIFIER ::= { fcMgmtConformance 1 } -- fcMgmtGroups OBJECT IDENTIFIER ::= { fcMgmtConformance 2 } -- Compliance statements fcMgmtCompliance MODULE-COMPLIANCE STATUS current DESCRIPTION "The compliance statement for Fibre Channel entities which implement this MIB module." MODULE -- this module MANDATORY-GROUPS { -- support for these groups is mandatory -- for all agents implementing this MIB fcConnUnitGroup, fcCuEventGroup, fcCuLinkGroup, fcCuPortStatsGroup, fcCuTrapFiltersGroup, fcCuNotificationsGroup } GROUP fcCuSNSGroup DESCRIPTION "This group is mandatory for agents supporting fibre channel connectivity units that support switch protocol." ::= { fcMgmtCompliances 1 } -- Conformance units -- the fibre channel connectivity unit group fcConnUnitGroup OBJECT-GROUP OBJECTS { -- scalars fcConnUnitNumber, fcConnURL, -- fcConnUnitTable fcConnUnitGlobalId, fcConnUnitType, fcConnUnitNumPorts, fcConnUnitState, fcConnUnitStatus, fcConnUnitProduct, fcConnUnitSerialNo, fcConnUnitUpTime, fcConnUnitUrl, fcConnUnitDomainId, fcConnUnitProxyMaster, fcConnUnitPrincipal, fcConnUnitNumSensors, fcConnUnitNumRevs, fcConnUnitModuleId, fcConnUnitName, fcConnUnitInfo, fcConnUnitControl, fcConnUnitContact, fcConnUnitLocation, fcConnUnitEventFilter, fcConnUnitNumEvents, fcConnUnitMaxEvents, fcConnUnitEventCurrID, -- fcConnUnitRevsTable fcConnUnitRevsRevision, fcConnUnitRevsDescription, -- fcConnUnitSensorTable fcConnUnitSensorName, fcConnUnitSensorStatus, fcConnUnitSensorInfo, fcConnUnitSensorMessage, fcConnUnitSensorType, fcConnUnitSensorCharacteristic, -- fcConnUnitPortTable fcConnUnitPortType, fcConnUnitPortFCClassCap, fcConnUnitPortFCClassOp, fcConnUnitPortState, fcConnUnitPortStatus, fcConnUnitPortTransmitterType, fcConnUnitPortModuleType, fcConnUnitPortWwn, fcConnUnitPortFCId, fcConnUnitPortSerialNo, fcConnUnitPortRevision, fcConnUnitPortVendor, fcConnUnitPortSpeed, fcConnUnitPortControl, fcConnUnitPortName, fcConnUnitPortPhysicalNumber, fcConnUnitPortProtocolCap, fcConnUnitPortProtocolOp, fcConnUnitPortNodeWwn, fcConnUnitPortHWState} STATUS current DESCRIPTION "The collection of objects providing Fibre Channel connectivity unit instrumentation and control." ::= { fcMgmtGroups 1 } -- event group fcCuEventGroup OBJECT-GROUP OBJECTS { -- fcConnUnitEventTable fcConnUnitEventIndex, fcConnUnitREventTime, fcConnUnitSEventTime, fcConnUnitEventSeverity, fcConnUnitEventType, fcConnUnitEventObject, fcConnUnitEventDescr } STATUS current DESCRIPTION "The collection of objects providing Fibre Channel connectivity unit event information." ::= { fcMgmtGroups 2 } -- link group fcCuLinkGroup OBJECT-GROUP OBJECTS { -- fcConnUnitLinkTable fcConnUnitLinkIndex, fcConnUnitLinkNodeIdX, fcConnUnitLinkPortNumberX, fcConnUnitLinkPortWwnX, fcConnUnitLinkNodeIdY, fcConnUnitLinkPortNumberY, fcConnUnitLinkPortWwnY, fcConnUnitLinkAgentAddressY, fcConnUnitLinkAgentAddressTypeY, fcConnUnitLinkAgentPortY, fcConnUnitLinkUnitTypeY, fcConnUnitLinkConnIdY } STATUS current DESCRIPTION "The collection of objects providing Fibre Channel connectivity unit link (topology) information." ::= { fcMgmtGroups 3 } -- Port statistics group fcCuPortStatsGroup OBJECT-GROUP OBJECTS { -- fcConnUnitPortStatTable fcConnUnitPortStatIndex, fcConnUnitPortStatErrs, fcConnUnitPortStatTxObjects, fcConnUnitPortStatRxObjects, fcConnUnitPortStatTxElements, fcConnUnitPortStatRxElements, fcConnUnitPortStatBBCreditZero, fcConnUnitPortStatInputBuffsFull, fcConnUnitPortStatFBSYFrames, fcConnUnitPortStatPBSYFrames, fcConnUnitPortStatFRJTFrames, fcConnUnitPortStatPRJTFrames, fcConnUnitPortStatC1RxFrames, fcConnUnitPortStatC1TxFrames, fcConnUnitPortStatC1FBSYFrames, fcConnUnitPortStatC1PBSYFrames, fcConnUnitPortStatC1FRJTFrames, fcConnUnitPortStatC1PRJTFrames, fcConnUnitPortStatC2RxFrames, fcConnUnitPortStatC2TxFrames, fcConnUnitPortStatC2FBSYFrames, fcConnUnitPortStatC2PBSYFrames, fcConnUnitPortStatC2FRJTFrames, fcConnUnitPortStatC2PRJTFrames, fcConnUnitPortStatC3RxFrames, fcConnUnitPortStatC3TxFrames, fcConnUnitPortStatC3Discards, fcConnUnitPortStatRxMcastObjects, fcConnUnitPortStatTxMcastObjects, fcConnUnitPortStatRxBcastObjects, fcConnUnitPortStatTxBcastObjects, fcConnUnitPortStatRxLinkResets, fcConnUnitPortStatTxLinkResets, fcConnUnitPortStatLinkResets, fcConnUnitPortStatRxOfflineSeqs, fcConnUnitPortStatTxOfflineSeqs, fcConnUnitPortStatOfflineSeqs, fcConnUnitPortStatLinkFailures, fcConnUnitPortStatInvalidCRC, fcConnUnitPortStatInvalidTxWords, fcConnUnitPortStatPSPErrs, fcConnUnitPortStatLossOfSignal, fcConnUnitPortStatLossOfSync, fcConnUnitPortStatInvOrderedSets, fcConnUnitPortStatFramesTooLong, fcConnUnitPortStatFramesTooShort, fcConnUnitPortStatAddressErrs, fcConnUnitPortStatDelimiterErrs, fcConnUnitPortStatEncodingErrs } STATUS current DESCRIPTION "The collection of objects providing Fibre Channel connectivity unit port statistics." ::= { fcMgmtGroups 4 } -- Fibre Channel Simple Name Server group fcCuSNSGroup OBJECT-GROUP OBJECTS { -- scalars fcConnUnitSnsMaxRows, -- fcConnUnitSnsTable fcConnUnitSnsPortIndex, fcConnUnitSnsPortIdentifier, fcConnUnitSnsPortName, fcConnUnitSnsNodeName, fcConnUnitSnsClassOfSvc, fcConnUnitSnsNodeIPAddress, fcConnUnitSnsProcAssoc, fcConnUnitSnsFC4Type, fcConnUnitSnsPortType, fcConnUnitSnsPortIPAddress, fcConnUnitSnsFabricPortName, fcConnUnitSnsHardAddress, fcConnUnitSnsSymbolicPortName, fcConnUnitSnsSymbolicNodeName } STATUS current DESCRIPTION "The collection of objects providing Fibre Channel connectivity unit simple name server information." ::= { fcMgmtGroups 5 } -- SNMP trap filter group fcCuTrapFiltersGroup OBJECT-GROUP OBJECTS { -- scalars fcTrapMaxClients, fcTrapClientCount, -- fcTrapRegTable fcTrapRegIpAddress, fcTrapRegPort, fcTrapRegFilter, fcTrapRegRowState } STATUS current DESCRIPTION "The collection of objects controlling SNMP notification (i.e., trap) destinations." ::= { fcMgmtGroups 6 } -- FC-MGMT-MIB notifications group fcCuNotificationsGroup NOTIFICATION-GROUP NOTIFICATIONS { fcConnUnitStatusChange, fcConnUnitDeletedTrap, fcConnUnitEventTrap, fcConnUnitSensorStatusChange, fcConnUnitPortStatusChange } STATUS current DESCRIPTION "The set of SNMP notifications which an agent is required to implement." ::= { fcMgmtGroups 7 } -- END