PDN-DS1CONFIG-MIB DEFINITIONS ::= BEGIN IMPORTS DisplayString FROM RFC1213-MIB Gauge FROM RFC1155-SMI OBJECT-TYPE FROM RFC-1212 pdn-interfaces FROM PDN-HEADER-MIB; -- =============================================================== -- -- The Paradyne DS1 Interface Configuration Table. -- Release: 0.0.3 (6/27/96) DRAFT -- ent-ds1 OBJECT IDENTIFIER ::= { pdn-interfaces 5 } -- The following definitions are used to allow an SNMP -- management system to control certain test functions -- of a Paradyne device. devDS1Test OBJECT IDENTIFIER ::= { ent-ds1 1 } -- The Paradyne DS1 Interface Test Table. -- This table is used to define objects which allow a network -- manager to instruct the agent to test a DS1 interface for various -- faults. -- More than one test can be active on a particular interface. -- The valid combinations of tests allowed per interface are -- described in the Operator's Guide of the product. devDS1TestTable OBJECT-TYPE SYNTAX SEQUENCE OF DevDS1TestEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "The Paradyne DS1 Interface Test Table." ::= { devDS1Test 1 } devDS1TestEntry OBJECT-TYPE SYNTAX DevDS1TestEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "An entry in the Paradyne DS1 Interface Test Table." INDEX { devDS1TestIfIndex, devDS1TestType } ::= { devDS1TestTable 1 } -- Layout of one entry in devDS1TestTable. DevDS1TestEntry ::= SEQUENCE { devDS1TestIfIndex INTEGER, devDS1TestType INTEGER, devDS1TestControl INTEGER, devDS1TestArgument DisplayString } devDS1TestIfIndex OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The index value which uniquely identifies the interface for which this entry contains information on interface tests. The interface identified by a particular value of this index is the same interface as identified by the same value of ifIndex from the Interfaces table of MIB II (RFC 1213)." ::= { devDS1TestEntry 1 } devDS1TestType OBJECT-TYPE SYNTAX INTEGER { -- Remote Loopback Tests llbup(1), -- line loopback up code sent to -- the remote DSU/CSU for 10 secs llbdn(2), -- line loopback down code sent to -- the remote DSU/CSU for 10 secs -- Local Loopback Tests llb(3), -- line loopback plb(4), -- payload loopback rlb(5), -- repeater loopback -- Test Patterns sendQRSS(6), -- sends QRSS test pattern sendZeros(7), -- sends an all zeros test pattern sendOnes(8), -- sends an all ones test pattern send1in8(9), -- sends a 1-in-8 test pattern send3in24(10), -- sends a 3-in-24 test pattern send63(11), -- sends a 63 test pattern send511(12), -- sends a 511 test pattern send2047(13), -- sends a 2047 test pattern send2E15(14), -- sends a 2E15-1 test pattern send2E20(15), -- sends a 2E20-1 test pattern sendUserDefined(16), -- sends a user defined test pattern -- (requires use of devDS1TestArgument) monQRSS(17), -- monitors a QRSS pattern monZeros(18), -- monitors an all zeros test pattern monOnes(19), -- monitors an all ones test pattern mon1in8(20), -- monitors a 1-in-8 test pattern mon3in24(21), -- monitors a 3-in-24 test pattern mon63(22), -- monitors a 63 test pattern mon11(23), -- monitors a 511 pattern mon2047(24), -- monitors a 2047 test pattern mon2E15(25), -- monitors a 2E15-1 test pattern mon2E20(26), -- monitors a 2E20-1 test pattern monUserDefined(27) -- monitors a user defined test pattern -- (requires use of devDS1TestArgument) } ACCESS read-only STATUS mandatory DESCRIPTION "The index value which uniquely identifies the test for which this entry contains information." ::= { devDS1TestEntry 2 } devDS1TestControl OBJECT-TYPE SYNTAX INTEGER { idle(1), -- stop the currently running test or no -- test currently active running(2) -- start the test or the test is -- currently active } ACCESS read-write STATUS mandatory DESCRIPTION "A control variable used to start and stop operator- initiated interface tests. Writing idle(1) to the test table entry terminates the specified test for the interface associated with the entry. Writing running(2) activates the specified test for the interface, if allowed (i.e., the test must be allowed for the interface and in combination with any other tests currently executing for the interface). The rules for executing tests for the product are specified in the product's Operator's Guide. This variable is read to determine the current status of the test for the interface. A value of running(2) indicates the test is currently in progress on the interface. A value of idle(1) indicates that the test is currently not active on the interface." ::= { devDS1TestEntry 3 } devDS1TestArgument OBJECT-TYPE SYNTAX DisplayString (SIZE (0..255)) ACCESS read-write STATUS mandatory DESCRIPTION "Any argument required by the test being executed." ::= { devDS1TestEntry 4 } -- The Paradyne Device Monitor Test Pattern Result Table. -- This table is used to define objects which reflect the result -- of a monitor test pattern request. devDS1MonResultTable OBJECT-TYPE SYNTAX SEQUENCE OF DevDS1MonResultEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "The Paradyne Device Monitor Test Pattern Result Table." ::= { devDS1Test 2 } devDS1MonResultEntry OBJECT-TYPE SYNTAX DevDS1MonResultEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "An entry in the Paradyne Device Monitor Test Pattern Result Table." INDEX { devDS1MonResultIfIndex, devDS1MonResultTestType } ::= { devDS1MonResultTable 1 } -- Layout of one entry in devDS1MonResultTable. DevDS1MonResultEntry ::= SEQUENCE { devDS1MonResultIfIndex INTEGER, devDS1MonResultTestType INTEGER, devDS1MonResultCode INTEGER, devDS1MonResultErrorCount Gauge } devDS1MonResultIfIndex OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The index value which uniquely identifies the interface for which this entry contains information on the result of the monitor test pattern request. The interface identified by a particular value of this index is the same interface as identified by the same value of ifIndex from the Interfaces table of MIB II (RFC 1213)." ::= { devDS1MonResultEntry 1 } devDS1MonResultTestType OBJECT-TYPE SYNTAX INTEGER { monQRSS(17), -- monitor QRSS pattern monZeros(18), -- monitor all zeros test pattern monOnes(19), -- monitor all ones test pattern mon1in8(20), -- monitor 1-in-8 test pattern mon3in24(21), -- monitor 3-in-24 test pattern mon63(22), -- monitor 63 test pattern mon11(23), -- monitor 511 pattern mon2047(24), -- monitor 2047 test pattern mon2E15(25), -- monitor 2E15-1 test pattern mon2E20(26), -- monitor 2E20-1 test pattern monUserDefined(27) -- monitor user defined test pattern } ACCESS read-only STATUS mandatory DESCRIPTION "The index value which uniquely identifies the test for which this entry contains information." ::= { devDS1MonResultEntry 2 } devDS1MonResultCode OBJECT-TYPE SYNTAX INTEGER { none(1), -- no further information is available inSyncNoBitErrors(2), -- the monitor pattern test has -- synchronized on the pattern and has -- not detected any bit errors inSyncWithBitErrors(3), -- the monitor pattern test has -- synchronized on the pattern and has -- detected bit errors notInSync(4) -- a monitor pattern test has not -- synchronized on the requested pattern } ACCESS read-only STATUS mandatory DESCRIPTION "This object contains a code for more specific information on the test pattern monitoring result. A value of none(1) indicates that no further information is available. inSyncNoBitErrors(2) notes that the monitor pattern test has synchronized on the pattern and has not detected any bit errors. inSyncWithBitErrors indicates that the monitor pattern test has synchronized on the pattern and has detected bit errors. A monitor pattern test that has not synchronized on the request pattern returns a value of notInSync(4)." ::= { devDS1MonResultEntry 3 } devDS1MonResultErrorCount OBJECT-TYPE SYNTAX Gauge ACCESS read-write STATUS mandatory DESCRIPTION "The number of bit errors detected in the received monitoring test pattern. The error count is updated once every second. The error count does not increment during periods when the pattern is not synchronized, or once synchronization is lost. The maximum value of this object is 99,999. Writing any value to this object will reset it to zero." ::= { devDS1MonResultEntry 4 } -- The Paradyne Device Send Test Pattern Control Table. -- This table is used to define objects related to a send test -- pattern request. devDS1SendControlTable OBJECT-TYPE SYNTAX SEQUENCE OF DevDS1SendControlEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "The Paradyne Device Send Test Pattern Control Table." ::= { devDS1Test 3 } devDS1SendControlEntry OBJECT-TYPE SYNTAX DevDS1SendControlEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "An entry in the Paradyne Device Send Test Pattern Control Table." INDEX { devDS1SendControlIfIndex } ::= { devDS1SendControlTable 1 } -- Layout of one entry in devDS1SendControlTable. DevDS1SendControlEntry ::= SEQUENCE { devDS1SendControlIfIndex INTEGER, devDS1SendControlInjectErr INTEGER, devDS1SendControlErrorCount Gauge } devDS1SendControlIfIndex OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "The index value which uniquely identifies the interface for which this entry contains information on the result of the monitor test pattern request. The interface identified by a particular value of this index is the same interface as identified by the same value of ifIndex from the Interfaces table of MIB II (RFC 1213)." ::= { devDS1SendControlEntry 1 } devDS1SendControlInjectErr OBJECT-TYPE SYNTAX INTEGER { noOp(1), inject(2) } ACCESS read-write STATUS mandatory DESCRIPTION "Setting this object to inject(2) will inject one error in the data pattern being sent. If no pattern is being sent, the agent will return BAD VALUE. Reading this value will always return noOp(1)." ::= { devDS1SendControlEntry 2 } devDS1SendControlErrorCount OBJECT-TYPE SYNTAX Gauge ACCESS read-only STATUS mandatory DESCRIPTION "The number of bit errors injected into the test pattern being sent. The maximum value of this object is 99,999." ::= { devDS1SendControlEntry 3 } END