PDN-SPECTRUMMGMT-MIB DEFINITIONS ::= BEGIN ---------------------------------------------------------------- -- Copyright (C) 2003, Paradyne. All rights reserved. ---------------------------------------------------------------- IMPORTS Integer32, Unsigned32, OBJECT-TYPE, MODULE-IDENTITY FROM SNMPv2-SMI MODULE-COMPLIANCE, OBJECT-GROUP FROM SNMPv2-CONF entPhysicalIndex FROM ENTITY-MIB ifIndex, ifType FROM IF-MIB pdn-interfaces FROM PDN-HEADER-MIB; pdnSpectrumMgmt MODULE-IDENTITY LAST-UPDATED "200212091500Z" ORGANIZATION "Paradyne Corp MIB Working Group" CONTACT-INFO "Paradyne Networks, Inc. 8545 126th Ave North Largo, FL 33733 www.paradyne.com General Comments to: mibwg_team@eng.paradyne.com Editors: R.A.Bowhall, Jesus Pinto" DESCRIPTION "R.A.Bowhall The Paradyne enterprise SPECTRUM MIB. This MIB is written to facilitate spectrum management of any xDSL interfaces. This mib replaces older versions of the spectrum management including the reachDSL.mib." REVISION "200301151300Z" DESCRIPTION "Jesus Pinto 1. Changed indexes on GeneralConfigTable. 2. Removed DSL Line Table. 3. Renamed newSpectrumMgmtAturMaxTxRate 4. Renamed newSpectrumMgmtAturMinTxRate 5. Renamed newSpectrumMgmtAturTxPower 6. Renamed newSpectrumMgmtAtucMinTxRate 7. Renamed newSpectrumMgmtAtucMaxTxRate 8. Renamed newSpectrumMgmtAtucTxPower 9. Added newSpectrumMgmtXturMax2TxRate 10.Added newSpectrumMgmtXturMin2TxRate 11.Added newSpectrumMgmtXtucMax2TxRate 12.Added newSpectrumMgmtXtucMax2TxRate" REVISION "200301091500Z" DESCRIPTION "Jesus Pinto 1. Deprecated spectrumMgmtTable and all its objects. 2. Added newSpectrumMgmtTable. 3. Added newSpectrumMgmtMode. 4. Added newSpectrumMgmtEWLUnits. 5. Added newSpectrumMgmtLoopMeasurementMethod. 6. Added newSpectrumMgmtLineInfoTable. 7. Added newSpectrumMgmtGeneralConfigTable." REVISION "0105161530Z" DESCRIPTION "R.A.Bowhall Added DEFVAL caluse, Added the pdnSpecMgmtTraps, and pdnSpecMgmtMIBConformance info. Added an Informational Note at the Beginning of this MIB." REVISION "0105080550Z" DESCRIPTION "R.A.Bowhall Added the EWL Deployment Guidelines Table and Changed spectrumMgmtAllowedSpeeds to spectrumMgmtAllowedSpeedsMin1, spectrumMgmtAllowedSpeedsMax1, spectrumMgmtAllowedSpeedsMin2, spectrumMgmtAllowedSpeedsMax2" ::= { pdn-interfaces 19 } pdnSpecMgmtObjects OBJECT IDENTIFIER ::= { pdnSpectrumMgmt 1 } pdnNewSpecMgmtObjects OBJECT IDENTIFIER ::= { pdnSpectrumMgmt 2 } -- -- START OF Spectrum Management definitions -- -- -- General options for spectrum management -- newSpectrumMgmtGeneralConfigTable OBJECT-TYPE SYNTAX SEQUENCE OF NewSpectrumMgmtGeneralConfigEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "General Configuration of the spectrum management. This table contains an entry for each technology managed by this device." ::= { pdnNewSpecMgmtObjects 1 } newSpectrumMgmtGeneralConfigEntry OBJECT-TYPE SYNTAX NewSpectrumMgmtGeneralConfigEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry with the general spectrum mgmt configuration parameters for a specific DSL technology." INDEX { entPhysicalIndex, ifType } ::= { newSpectrumMgmtGeneralConfigTable 1 } NewSpectrumMgmtGeneralConfigEntry ::= SEQUENCE { newSpectrumMgmtSelection INTEGER, newSpectrumMgmtMode INTEGER, newSpectrumMgmtLoopMeasurementMethod INTEGER, newSpectrumMgmtEWLUnits INTEGER } newSpectrumMgmtSelection OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "This object is used to Enable or Disable Spectrum Management on DSL interfaces managed by this device. Enabling this object limits the DSL speeds on each port based on line length in order to meet ANSI T1.417 Spectrum Management requirements or BT Access Network Spectrum requirements. The values that this object can accept are controlled by the -Mode- object." ::= { newSpectrumMgmtGeneralConfigEntry 1 } newSpectrumMgmtMode OBJECT-TYPE SYNTAX INTEGER { enableOnly(1), disableOnly(2), both(3) } MAX-ACCESS read-only STATUS current DESCRIPTION "This object restricts the MAX-ACCESS of the 'Selection' object. Following are the details of each of the values: enableOnly(1) - Indicates that the 'Selection' object IS always 'enabled' and cannot be set to 'disabled'. disableOnly(2) - Indicates that the 'Selection' object IS always 'disabled' and cannot be set to 'enabled'. both(3) - Indicates that the 'Selection' object will accept both the 'enabled' and 'disabled' values." ::= { newSpectrumMgmtGeneralConfigEntry 2 } newSpectrumMgmtLoopMeasurementMethod OBJECT-TYPE SYNTAX INTEGER { none(1), loopLength(2), ewl(3), quadMode(4) } MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the measurement method used in describing the Loop Length of a circuit. Following are the details of each of the options: none(1) - Indicates that the Spectral Compliance is NOT dependant on any Loop Length measurements or configurations. loopLength(2) - The 'ConfLoopLength' object is used to determine spectral compliance. The 'ConfEWL' & 'ConfQuadMode' objects are not used in this mode. ewl(3) - The 'ConfEWL' object is used to configure the estimated loop length, which is used to determine spectral compliance. In this mode the 'ConfLoopLength' & 'ConfQuadMode' objects are not used. quadMode(4) - The 'ConfQuadMode' object is used to determine spectral compliance. The 'ConfEWL' & 'ConfLoopLength' objects are not used in this mode. This object determines which of the three objects : 'ConfEWL', 'ConfLoopLength' or 'ConfQuadMode' is used (if any) to enforce spectrally compliant maximum 'Tx Rates' and the maximum allowed 'Tx Power' on a given circuit." ::= { newSpectrumMgmtGeneralConfigEntry 3 } newSpectrumMgmtEWLUnits OBJECT-TYPE SYNTAX INTEGER { none(1), feet(2), meters(3) } MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates the units of measurement used in describing the Estimated Working Length of a circuit. Following are the details of each of the units: none(1) - Indicates that the Spectral Compliance is NOT dependant on the 'ConfEWL' object. feet(2) - The 'ConfEWL' is measured and configured in feet. meters(3) - The 'ConfEWL' is measured and configured in meters." ::= { newSpectrumMgmtGeneralConfigEntry 4 } -- -- Spectrum Mgmt Configuration Table -- newSpectrumMgmtConfTable OBJECT-TYPE SYNTAX SEQUENCE OF NewSpectrumMgmtConfEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The new Spectrum Management Configuration Table This table is used for configuring spectrum management objects on any DSL interface." ::= { pdnNewSpecMgmtObjects 2 } newSpectrumMgmtConfEntry OBJECT-TYPE SYNTAX NewSpectrumMgmtConfEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in the xDSL Spectrum Management Configuration table. Note: This entry can be accessed only for ifIndex values that belong to a physical interface. e.g. for ifType = 'shdsl' (IANAifType=169)." INDEX { ifIndex } ::= { newSpectrumMgmtConfTable 1 } NewSpectrumMgmtConfEntry ::= SEQUENCE { newSpectrumMgmtConfEWL Unsigned32, newSpectrumMgmtConfLoopLength INTEGER, newSpectrumMgmtConfQuadMode INTEGER } newSpectrumMgmtConfEWL OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-write STATUS current DESCRIPTION "The Equivalent Working Length (EWL). The value selected corresponds to the estimated length of the line in feet - if 'EWLUnits' object is 'feet'. meters - if 'EWLUnits' object is 'meters'. This value is usually specified by the carrier and MUST be in integral multiples of 500 feet, if 'EWLUnits' is 'feet'. 200 meters, if 'EWLUnits' is 'meters'. The range of values that this object can take is determined by the 'MinEWL' and 'MaxEWL' objects. Changing this object may limit the maximum transmit power and the effective DSL speeds at which the ports train up. Note: This object will be used only if Spectrum Management is enabled and 'LoopMeasurementMethod' is 'ewl'. This object shares a mutual exclusion relationship with the 'ConfLoopLength' & 'ConfQuadMode' objects, as only one of the two will be used for configuration at any time." ::= { newSpectrumMgmtConfEntry 1 } newSpectrumMgmtConfLoopLength OBJECT-TYPE SYNTAX INTEGER { short(1), medium(2), long(3) } MAX-ACCESS read-write STATUS current DESCRIPTION "This entry specifies the loop length for the line. The configurable values are short(1), medium(2) and long(3). The 'Loop Length' feature can be used only if the 'shdslSpectrumMgmtSelection' object is Enabled and the 'LoopMeasurementMethod' is 'loopLength'. Changing this object may limit the maximum transmit power and the effective DSL speeds at which ports train up. Note: This object shares a mutual exclusion relationship with the 'ConfEWL' objects. i.e. only one of the three can be used for configuration at one time." ::= { newSpectrumMgmtConfEntry 2 } newSpectrumMgmtConfQuadMode OBJECT-TYPE SYNTAX INTEGER { sameQuad(1), segregatedQuadUpto3km(2), segregatedQuadAbove3km(3) } MAX-ACCESS read-write STATUS current DESCRIPTION "This entry specifies the quad cable configuration & length for the line. The configurable values are sameQuad(1), segregatedQuadUpto3km(2) and segregatedQuadAbove3km(3). The 'Quad Mode' feature can be used only if the 'reachDSLSpectrumMgmtSelection' object is Enabled and the 'LoopMeasurementMethod' is 'quadMode'. Changing this object may limit the maximum transmit power and the effective DSL speeds at which ports train up. Note: This object shares a mutual exclusion relationship with the 'ConfEWL' & 'ConfLoopLength' objects. i.e. only one of the three can be used for configuration at one time." ::= { newSpectrumMgmtConfEntry 3 } -- -- Spectrum Management Line Info Table -- newSpectrumMgmtLineInfoTable OBJECT-TYPE SYNTAX SEQUENCE OF NewSpectrumMgmtLineInfoEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The Spectrum Management Line Info Table. This table gives information about the spectrum management ranges that are applicable for each port, based on the spectral requirements for the device." ::= { pdnNewSpecMgmtObjects 3 } newSpectrumMgmtLineInfoEntry OBJECT-TYPE SYNTAX NewSpectrumMgmtLineInfoEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry in the newSpectrumMgmtLineInfoTable table. Note: This entry can be accessed only for ifIndex values that belong to a physical interface. e.g. for ifType = 'adsl'." INDEX { ifIndex } ::= { newSpectrumMgmtLineInfoTable 1 } NewSpectrumMgmtLineInfoEntry ::= SEQUENCE { newSpectrumMgmtXtucMax1TxRate Unsigned32, newSpectrumMgmtXtucMin1TxRate Unsigned32, newSpectrumMgmtXtucMax2TxRate Unsigned32, newSpectrumMgmtXtucMin2TxRate Unsigned32, newSpectrumMgmtXtucMaxTxPower INTEGER, newSpectrumMgmtXturMax1TxRate Unsigned32, newSpectrumMgmtXturMin1TxRate Unsigned32, newSpectrumMgmtXturMax2TxRate Unsigned32, newSpectrumMgmtXturMin2TxRate Unsigned32, newSpectrumMgmtXturMaxTxPower INTEGER, newSpectrumMgmtMinEWL Unsigned32, newSpectrumMgmtMaxEWL Unsigned32 } newSpectrumMgmtXtucMax1TxRate OBJECT-TYPE SYNTAX Unsigned32 UNITS "bps" MAX-ACCESS read-only STATUS current DESCRIPTION "This rate will be the max allowed Tx Rate(in bps) for the port based on the Spectrum Management requirements for XTUC in a particular spectral compliance configuration. Some measurement methods may have more than one range for the TxRate. Min1TxRate and Max1TxRate will always have the first range of values and the Min2TxRate and Max2TxRate will have the second range if the method demands it." ::= { newSpectrumMgmtLineInfoEntry 1 } newSpectrumMgmtXtucMin1TxRate OBJECT-TYPE SYNTAX Unsigned32 UNITS "bps" MAX-ACCESS read-only STATUS current DESCRIPTION "This rate will be the min allowed Tx Rate based on the spectrum management requirements for the XTUC. The MinTxRate will be upper bounded by 'newSpectrumMgmtXtucMax1TxRate' object. Some measurement methods may have more than one range for the TxRate. Min1TxRate and Max1TxRate will always have the first range of values and the Min2TxRate and Max2TxRate will have the second range if the method demands it." ::= { newSpectrumMgmtLineInfoEntry 2 } newSpectrumMgmtXtucMax2TxRate OBJECT-TYPE SYNTAX Unsigned32 UNITS "bps" MAX-ACCESS read-only STATUS current DESCRIPTION "This rate will be the max allowed Tx Rate(in bps) for the port based on the Spectrum Management requirements for XTUC in a particular spectral compliance configuration. This object is the Some measurement methods may have more than one range for the TxRate. Min1TxRate and Max1TxRate will always have the first range of values and the Min2TxRate and Max2TxRate will have the second range if the method demands it." ::= { newSpectrumMgmtLineInfoEntry 3 } newSpectrumMgmtXtucMin2TxRate OBJECT-TYPE SYNTAX Unsigned32 UNITS "bps" MAX-ACCESS read-only STATUS current DESCRIPTION "This rate will be the min allowed Tx Rate based on the spectrum management requirements for the XTUC. The MinTxRate will be upper bounded by 'newSpectrumMgmtXtucMax1TxRate' object. Some measurement methods may have more than one range for the TxRate. Min1TxRate and Max1TxRate will always have the first range of values and the Min2TxRate and Max2TxRate will have the second range if the method demands it." ::= { newSpectrumMgmtLineInfoEntry 4 } newSpectrumMgmtXtucMaxTxPower OBJECT-TYPE SYNTAX INTEGER(-140..120) UNITS "tenth dB" MAX-ACCESS read-only STATUS current DESCRIPTION "The maximum transmit power at the ATUC (in tenth dB). This value will be based on the spectrum management selection." ::= { newSpectrumMgmtLineInfoEntry 5 } newSpectrumMgmtXturMax1TxRate OBJECT-TYPE SYNTAX Unsigned32 UNITS "bps" MAX-ACCESS read-only STATUS current DESCRIPTION "This rate will be the max allowed Tx Rate(in bps) for the port based on the Spectrum Management requirements for XTUR in a particular spectral compliance configuration. This object is the Some measurement methods may have more than one range for the TxRate. Min1TxRate and Max1TxRate will always have the first range of values and the Min2TxRate and Max2TxRate will have the second range if the method demands it." ::= { newSpectrumMgmtLineInfoEntry 6 } newSpectrumMgmtXturMin1TxRate OBJECT-TYPE SYNTAX Unsigned32 UNITS "bps" MAX-ACCESS read-only STATUS current DESCRIPTION "This rate will be the min allowed Tx Rate based on the spectrum management requirements for the XTUR. The MinTxRate will be upper bounded by 'newSpectrumMgmtXturMax1TxRate' object. Some measurement methods may have more than one range for the TxRate. Min1TxRate and Max1TxRate will always have the first range of values and the Min2TxRate and Max2TxRate will have the second range if the method demands it." ::= { newSpectrumMgmtLineInfoEntry 7 } newSpectrumMgmtXturMax2TxRate OBJECT-TYPE SYNTAX Unsigned32 UNITS "bps" MAX-ACCESS read-only STATUS current DESCRIPTION "This rate will be the max allowed Tx Rate(in bps) for the port based on the Spectrum Management requirements for XTUR in a particular spectral compliance configuration. Some measurement methods may have more than one range for the TxRate. Min1TxRate and Max1TxRate will always have the first range of values and the Min2TxRate and Max2TxRate will have the second range if the method demands it." ::= { newSpectrumMgmtLineInfoEntry 8 } newSpectrumMgmtXturMin2TxRate OBJECT-TYPE SYNTAX Unsigned32 UNITS "bps" MAX-ACCESS read-only STATUS current DESCRIPTION "This rate will be the min allowed Tx Rate based on the spectrum management requirements for the XTUR. The MinTxRate will be upper bounded by 'newSpectrumMgmtXtucMax1TxRate' object. Some measurement methods may have more than one range for the TxRate. Min1TxRate and Max1TxRate will always have the first range of values and the Min2TxRate and Max2TxRate will have the second range if the method demands it." ::= { newSpectrumMgmtLineInfoEntry 9 } newSpectrumMgmtXturMaxTxPower OBJECT-TYPE SYNTAX INTEGER(-140..120) UNITS "tenth dB" MAX-ACCESS read-only STATUS current DESCRIPTION "The maximum transmit power at the ATUR (in tenth dB). This value will be based on the spectrum management selection." ::= { newSpectrumMgmtLineInfoEntry 10 } newSpectrumMgmtMinEWL OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "The minimum value (in feet, if 'EWLUnits' is 'feet, or in meters, if 'EWLUnits' is 'meters') that the 'ConfEWL' object can accept. Together with the 'MaxEWL' object, this object indicates the range of EWL when 'EWLUnits' is either 'feet' or 'meters'. Note : This object is valid only if the 'LoopMeasurementMethod' object is 'ewl'." ::= { newSpectrumMgmtLineInfoEntry 11 } newSpectrumMgmtMaxEWL OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "The maximum value (in feet, if 'EWLUnits' is 'feet, or in meters, if 'EWLUnits' is 'meters') that the 'ConfEWL' object can accept. Together with the 'MinEWL' object, this object indicates the range of EWL when 'EWLUnits' is either 'feet' or 'meters'. Note : This object is valid only if the 'LoopMeasurementMethod' object is 'ewl'." ::= { newSpectrumMgmtLineInfoEntry 12 } -- -- D E P R E C A T E D -- -- The following objects are supported for the first version -- of the shdsl cards. They are now deprecated and should not -- be used for future products. -- spectrumMgmtCountryCode OBJECT-TYPE SYNTAX INTEGER { usa(1), uk(2) } MAX-ACCESS read-write STATUS deprecated DESCRIPTION "This object selects which Spectrum Management standard will be used on this device to calculate the 'allowed speeds' to comply with Spectrum Management. Note:Spectrum Management must be Enabled for 'Country Code' to take effect. 'USA' is the only valid selection for Region Setting 'Annex A', 'UK' will not be selectable. 'UK' for is the only valid selecton for Region Setting 'Annex B', 'USA' will not be selectable." DEFVAL { usa } ::= { pdnSpecMgmtObjects 2 } spectrumMgmtTable OBJECT-TYPE SYNTAX SEQUENCE OF SpectrumMgmtEntry MAX-ACCESS not-accessible STATUS deprecated DESCRIPTION "The Spectrum Management Table." ::= { pdnSpecMgmtObjects 3 } spectrumMgmtEntry OBJECT-TYPE SYNTAX SpectrumMgmtEntry MAX-ACCESS not-accessible STATUS deprecated DESCRIPTION "An entry in the Spectrum Management table." INDEX { ifIndex } ::= { spectrumMgmtTable 1 } SpectrumMgmtEntry ::= SEQUENCE { spectrumMgmtEWL Integer32, spectrumMgmtLineLength INTEGER, spectrumMgmtAllowedSpeedsMin1 Integer32, spectrumMgmtAllowedSpeedsMax1 Integer32, spectrumMgmtAllowedSpeedsMin2 Integer32, spectrumMgmtAllowedSpeedsMax2 Integer32 } spectrumMgmtEWL OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-write STATUS deprecated DESCRIPTION "The Estimated Working Length [EWL(ft)]. The value selected is the estimated length of the line in ft. See the Deployment guideline Table below. This value is usually specified by the carrier. This value is only required if spectrumMgmt is Enabled and the spectrumMgmtCountryCode selected is 'USA'." ::= { spectrumMgmtEntry 1 } -- Estimated Working Length Deployment guidelines for G.shdsl -- --------------------------------------------------------- -- | Line Bit Rate(kbps) | Deployment guideline,EWL (ft) | -- --------------------------------------------------------- -- | LBR <= 592 | 15500 | -- --------------------------------------------------------- -- | 600 <= LBR <= 616 | 15000 | -- | 624 <= LBR <= 648 | 14500 | -- |---------------------------------------------------------| -- | 656 <= LBR <= 688 | 14000 | -- | 696 <= LBR <= 800 | 13500 | -- |---------------------------------------------------------| -- | 808 <= LBR <= 832 | 12500 | -- | 840 <= LBR <= 896 | 12000 | -- |---------------------------------------------------------| -- | 904 <= LBR <= 952 | 13000 | -- | 960 <= LBR <= 1000 | 12500 | -- |---------------------------------------------------------| -- | 1008 <= LBR <= 1088 | 12000 | -- | 1096 <= LBR <= 1160 | 11500 | -- |---------------------------------------------------------| -- | 1168 <= LBR <= 1320 | 11000 | -- | 1328 <= LBR <= 1472 | 10500 | -- |---------------------------------------------------------| -- | 1480 <= LBR <= 1536 | 10000 | -- | 1544 <= LBR <= 1552 | 10500 | -- |---------------------------------------------------------| -- | 1560 <= LBR <= 1664 | 10000 | -- | 1672 <= LBR <= 1880 | 9500 | -- |---------------------------------------------------------| -- | 1888 <= LBR <= 2008 | 9000 | -- | 2016 <= LBR <= 2320 | 8500 | -- --------------------------------------------------------- -- Where LBR = Line Bit Rate -- -- Note:Equivalent Working Length(EWL):EWL=L26+3(L24)/4, -- where L26 is the total length of 26-gauge cable -- in the loop excluding any bridged tap and L24 is -- the total length of 19,22 or 24-gauge cable in -- the loop excluding any bridged tap. All lengths -- are in kilofeet (ft). This formula is suitable for -- use with systems operating below 1.1MHz. -- -- Note: Some EWL may have more then one range i.e., EWL -- =12.5 Kft - ranges 192 Kbit/s to 832Kbits and 960 kbits -- to 1000 kbits -- spectrumMgmtAllowedSpeedsMin1 OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS deprecated DESCRIPTION "This rate will be the Minimum Line Bit Rate based on the Line Length selected. See the Deployment guideline Table above. Example: EWL=12.5 this value may be 808kbps" ::= { spectrumMgmtEntry 2 } spectrumMgmtAllowedSpeedsMax1 OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS deprecated DESCRIPTION "This rate will be the Maximum Line Bit Rate based on the Line Length selected See the Deployment guideline Table above. Example: EWL=12.5 this value may be 832kbps" ::= { spectrumMgmtEntry 3 } spectrumMgmtAllowedSpeedsMin2 OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS deprecated DESCRIPTION "This rate will be the Minimum Line Bit Rate based on the Line Length selected. See the Deployment guideline Table above. Example: EWL=12.5 this value may be 960kbps" ::= { spectrumMgmtEntry 4 } spectrumMgmtAllowedSpeedsMax2 OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS deprecated DESCRIPTION "This rate will be the Maximum Line Bit Rate based on the Line Length selected. See the Deployment guideline Table above. Example: EWL=12.5 this value may be 1000kbps" ::= { spectrumMgmtEntry 5 } spectrumMgmtLineLength OBJECT-TYPE SYNTAX INTEGER { short(1), medium(2), long(3) } MAX-ACCESS read-write STATUS deprecated DESCRIPTION "This 'Line Length' feature is only required if the SpectrumMgmt is Enabled and the spectrumMgmtCountryCode selected is 'UK'. 'Short' Line Length from the exchange can support speeds up to 2056 Kbps. 'Medium' Line Length can support speeds up to 1496 Kbps. 'Long' Line Length can suppport speeds up to 872 Kbps." DEFVAL { short } ::= { spectrumMgmtEntry 6 } -- -- C O N F O R M A N C E S T A T E M E N T S -- pdnSpecMgmtConformance OBJECT IDENTIFIER ::= { pdnSpectrumMgmt 3 } pdnSpecMgmtGroups OBJECT IDENTIFIER ::= { pdnSpecMgmtConformance 1 } pdnSpecMgmtCompliances OBJECT IDENTIFIER ::= { pdnSpecMgmtConformance 2 } -- -- C O M P L I A N C E S T A T E M E N T S -- pdnSpecMgmtCompliance MODULE-COMPLIANCE STATUS current DESCRIPTION "The compliance statement for SNMP entities that control spectrum management on interfaces." MODULE -- this module MANDATORY-GROUPS { pdnGeneralConfigGroup, pdnLineInfoGroup } -- -- Groups -- -- pdnEWLModeGroup, -- pdnLoopLengthModeGroup, -- pdnQuadModeGroup -- -- are mutually exclusive; that is, at most one of these groups -- is implemented for a particular DSL interface. If the -- Loop Measurement Method is 'none', then none of these groups -- should be implemented. -- GROUP pdnEWLModeGroup DESCRIPTION "This group is mandatory for DSL interfaces whose loop/line length measurement method is EWL. i.e.the newSpectrumMgmtLoopMeasurementMethod object is 'ewl'." GROUP pdnLoopLengthModeGroup DESCRIPTION "This group is mandatory for DSL interfaces whose loop/line length measurement method is LoopLength. i.e.the newSpectrumMgmtLoopMeasurementMethod object is 'loopLength'." GROUP pdnQuadModeGroup DESCRIPTION "This group is mandatory for DSL interfaces whose loop/line length measurement method is based on Quads. i.e.the newSpectrumMgmtLoopMeasurementMethod object is 'quadMode'." OBJECT newSpectrumMgmtSelection MIN-ACCESS read-only DESCRIPTION "Write access is not required." ::= { pdnSpecMgmtCompliances 1 } -- -- U N I T S O F C O N F O R M A N C E -- -- Mandatory group pdnGeneralConfigGroup OBJECT-GROUP OBJECTS { newSpectrumMgmtSelection, newSpectrumMgmtMode, newSpectrumMgmtLoopMeasurementMethod, newSpectrumMgmtEWLUnits } STATUS current DESCRIPTION "A collection of general configuration objects required for the spectrum management of interfaces." ::= { pdnSpecMgmtGroups 1 } -- Mandatory group pdnLineInfoGroup OBJECT-GROUP OBJECTS { newSpectrumMgmtXtucMax1TxRate, newSpectrumMgmtXtucMin1TxRate, newSpectrumMgmtXtucMax2TxRate, newSpectrumMgmtXtucMin2TxRate, newSpectrumMgmtXtucMaxTxPower, newSpectrumMgmtXturMax1TxRate, newSpectrumMgmtXturMin1TxRate, newSpectrumMgmtXturMax2TxRate, newSpectrumMgmtXturMin2TxRate, newSpectrumMgmtXturMaxTxPower, newSpectrumMgmtMinEWL, newSpectrumMgmtMaxEWL } STATUS current DESCRIPTION "A collection of objects providing information regarding spectrum management of interfaces." ::= { pdnSpecMgmtGroups 2 } -- -- Optional group -- (pdnEWLModeGroup, pdnLineLoopModeGroup or pdnQuadModeGroup -- should be implemented) -- pdnEWLModeGroup OBJECT-GROUP OBJECTS { newSpectrumMgmtConfEWL, newSpectrumMgmtMinEWL, newSpectrumMgmtMaxEWL } STATUS current DESCRIPTION " A collection of configuration objects used to control spectrum management of DSL intfs when the measurement method is 'EWL'." ::= { pdnSpecMgmtGroups 3 } -- -- Optional group -- (pdnEWLModeGroup, pdnLineLoopModeGroup or pdnQuadModeGroup -- should be implemented) -- pdnLoopLengthModeGroup OBJECT-GROUP OBJECTS { newSpectrumMgmtConfLoopLength } STATUS current DESCRIPTION " A collection of configuration objects used to control spectrum management of DSL intfs when the measurement method is 'LoopLength' " ::= { pdnSpecMgmtGroups 4 } -- -- Optional group -- (pdnEWLModeGroup, pdnLineLoopModeGroup or pdnQuadModeGroup -- should be implemented) -- pdnQuadModeGroup OBJECT-GROUP OBJECTS { newSpectrumMgmtConfQuadMode } STATUS current DESCRIPTION "A collection of object(s) providing configuration access and information specific to DSL interfaces whose loop/line length measurement method is based on the Quad configuration. i.e.the newSpectrumMgmtLoopMeasurementMethod object is 'quadMode'." ::= { pdnSpecMgmtGroups 5 } -- -- D E P R E C A T E D G R O U P S -- pdnSpectrumMgmtDeprecatedGroup OBJECT-GROUP OBJECTS { spectrumMgmtCountryCode, spectrumMgmtEWL, spectrumMgmtLineLength, spectrumMgmtAllowedSpeedsMin1, spectrumMgmtAllowedSpeedsMax1, spectrumMgmtAllowedSpeedsMin2, spectrumMgmtAllowedSpeedsMax2 } STATUS deprecated DESCRIPTION " Deprecated objects " ::= { pdnSpecMgmtGroups 7 } END