-- ***************************************************************** -- This mib was extracted from draft-ietf-pim-mib-v2-01.txt -- -- $Copyright$ -- -- ***************************************************************** MY-PIM-MIB DEFINITIONS ::= BEGIN IMPORTS MODULE-IDENTITY, OBJECT-TYPE, experimental, NOTIFICATION-TYPE, Integer32, IpAddress, TimeTicks FROM SNMPv2-SMI DisplayString, RowStatus, TruthValue FROM SNMPv2-TC MODULE-COMPLIANCE, OBJECT-GROUP, NOTIFICATION-GROUP FROM SNMPv2-CONF ipMRouteGroup, ipMRouteSource, ipMRouteSourceMask, ipMRouteNextHopGroup, ipMRouteNextHopSource, ipMRouteNextHopSourceMask, ipMRouteNextHopIfIndex, ipMRouteNextHopAddress FROM IPMROUTE-STD-MIB EnabledStatus FROM P-BRIDGE-MIB myMgmt FROM MY-SMI InterfaceIndex FROM IF-MIB; myPimMIB MODULE-IDENTITY LAST-UPDATED "200301200000Z" ORGANIZATION "$Company$" CONTACT-INFO " Tel: $Telephone$ E-mail: $E-mail$" DESCRIPTION "This module defines my Pim mibs." REVISION "200301200000Z" DESCRIPTION "Initial version of this MIB module." ::= { myMgmt 27} myPimMIBObjects OBJECT IDENTIFIER ::= { myPimMIB 1 } myPimTraps OBJECT IDENTIFIER ::= { myPimMIBObjects 2 } myPim OBJECT IDENTIFIER ::= { myPimMIBObjects 1 } myPimJoinPruneInterval OBJECT-TYPE SYNTAX Integer32 UNITS "seconds" MAX-ACCESS read-write STATUS current DESCRIPTION "The default interval at which periodic PIM-SM Join/Prune messages are to be sent." DEFVAL { 60 } ::= { myPim 1 } -- The PIM Interface Table myPimInterfaceTable OBJECT-TYPE SYNTAX SEQUENCE OF MyPimInterfaceEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The (conceptual) table listing the router's PIM interfaces. IGMP and PIM are enabled on all interfaces listed in this table." ::= { myPim 2 } myPimInterfaceEntry OBJECT-TYPE SYNTAX MyPimInterfaceEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry (conceptual row) in the myPimInterfaceTable." INDEX { myPimInterfaceIfIndex } ::= { myPimInterfaceTable 1 } MyPimInterfaceEntry ::= SEQUENCE { myPimInterfaceIfIndex InterfaceIndex, myPimInterfaceAddress IpAddress, myPimInterfaceNetMask IpAddress, myPimInterfaceMode INTEGER, myPimInterfaceDR IpAddress, myPimInterfaceHelloInterval Integer32, myPimInterfaceJoinPruneInterval Integer32, myPimInterfaceCBSRPreference Integer32, myPimInterfaceTrigHelloInterval Integer32, myPimInterfaceHelloHoldtime Integer32, myPimInterfaceLanPruneDelay Integer32, myPimInterfacePropagationDelay Integer32, myPimInterfaceOverrideInterval Integer32, myPimInterfaceGenerationID Integer32, myPimInterfaceJoinPruneHoldtime Integer32, myPimInterfaceGraftRetryInterval Integer32, myPimInterfaceMaxGraftRetries Integer32, myPimInterfaceSRTTLThreshold Integer32, myPimInterfaceLanDelayEnabled TruthValue, myPimInterfaceSRCapable TruthValue, myPimInterfaceDRPriority Integer32, myPimInterfaceNbrCounter Integer32, myPimInterfaceBsrBorderEnabled EnabledStatus, myPimInterfaceCountIn Integer32, myPimInterfaceCountOut Integer32, myPimInterfaceEnabled EnabledStatus, myPimNeighborFilterAcl DisplayString, myPimDrSupportAddressBound DisplayString } myPimInterfaceIfIndex OBJECT-TYPE SYNTAX InterfaceIndex MAX-ACCESS not-accessible STATUS current DESCRIPTION "The ifIndex value of this PIM interface." ::= { myPimInterfaceEntry 1 } myPimInterfaceAddress OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The IP address of the PIM interface." ::= { myPimInterfaceEntry 2 } myPimInterfaceNetMask OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The network mask for the IP address of the PIM interface." ::= { myPimInterfaceEntry 3 } myPimInterfaceMode OBJECT-TYPE SYNTAX INTEGER { dense(1), sparse(2), sparseDense(3) } MAX-ACCESS read-write STATUS current DESCRIPTION "The configured mode of this PIM interface. A value of sparseDense is only valid for PIMv1." DEFVAL { dense } ::= { myPimInterfaceEntry 4 } myPimInterfaceDR OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The Designated Router on this PIM interface." ::= { myPimInterfaceEntry 5 } myPimInterfaceHelloInterval OBJECT-TYPE SYNTAX Integer32(0..65535) UNITS "seconds" MAX-ACCESS read-write STATUS current DESCRIPTION "The frequency at which PIM Hello messages are transmitted on this interface." DEFVAL { 30 } ::= { myPimInterfaceEntry 6 } myPimInterfaceJoinPruneInterval OBJECT-TYPE SYNTAX Integer32 UNITS "seconds" MAX-ACCESS read-write STATUS current DESCRIPTION "The frequency at which PIM Join/Prune messages are transmitted on this PIM interface. The default value of this object is the pimJoinPruneInterval." ::= { myPimInterfaceEntry 7 } myPimInterfaceCBSRPreference OBJECT-TYPE SYNTAX Integer32 (-1..255) MAX-ACCESS read-write STATUS current DESCRIPTION "The preference value for the local interface as a candidate bootstrap router. The value of -1 is used to indicate that the local interface is not a candidate BSR interface." DEFVAL { 0 } ::= { myPimInterfaceEntry 8 } myPimInterfaceTrigHelloInterval OBJECT-TYPE SYNTAX Integer32 UNITS "seconds" MAX-ACCESS read-write STATUS current DESCRIPTION "The maximum time before a triggered PIM Hello message is transmitted on this interface." DEFVAL { 5 } ::= { myPimInterfaceEntry 9 } myPimInterfaceHelloHoldtime OBJECT-TYPE SYNTAX Integer32 (0..65535) UNITS "seconds" MAX-ACCESS read-write STATUS current DESCRIPTION "The value set in the Holdtime field of Hello messages transmitted on this interface. This should be 3.5 times the value of pimInterfaceHelloInterval." DEFVAL { 105 } ::= { myPimInterfaceEntry 10 } myPimInterfaceLanPruneDelay OBJECT-TYPE SYNTAX Integer32 { off (2), on (1) } MAX-ACCESS read-write STATUS current DESCRIPTION "Turns the LAN Prune Delay Option off and on on this interface." DEFVAL { off } ::= { myPimInterfaceEntry 11 } myPimInterfacePropagationDelay OBJECT-TYPE SYNTAX Integer32 (0..32767) UNITS "milliseconds" MAX-ACCESS read-write STATUS current DESCRIPTION "The value inserted into the LAN Prune Delay field of a LAN Prune Delay option on this interface." DEFVAL { 500 } ::= { myPimInterfaceEntry 12 } myPimInterfaceOverrideInterval OBJECT-TYPE SYNTAX Integer32 (0..65535) MAX-ACCESS read-write STATUS current DESCRIPTION "The value inserted into the Override Interval field of a LAN Prune Delay option on this interface." DEFVAL { 2500 } ::= { myPimInterfaceEntry 13 } myPimInterfaceGenerationID OBJECT-TYPE SYNTAX Integer32 { off (2), on (1) } MAX-ACCESS read-write STATUS current DESCRIPTION "Turns the Generation ID Option off and on on this interface." DEFVAL {off} ::= { myPimInterfaceEntry 14 } myPimInterfaceJoinPruneHoldtime OBJECT-TYPE SYNTAX Integer32 (0..65535) UNITS "seconds" MAX-ACCESS read-write STATUS current DESCRIPTION "The value inserted into the Holdtime field of a Join/ Prune message sent on this interface. The value should be 3.5 times pimInterfaceJoinPruneInterval." DEFVAL { 210 } ::= { myPimInterfaceEntry 15 } myPimInterfaceGraftRetryInterval OBJECT-TYPE SYNTAX Integer32 UNITS "seconds" MAX-ACCESS read-write STATUS current DESCRIPTION "The interval a PIM router waits for a Graft Ack before resending a Graft on this interface." DEFVAL { 3 } ::= { myPimInterfaceEntry 16 } myPimInterfaceMaxGraftRetries OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-write STATUS current DESCRIPTION "The maximum number of times this router will resend a Graft on this interface." DEFVAL { 2 } ::= { myPimInterfaceEntry 17 } myPimInterfaceSRTTLThreshold OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-write STATUS current DESCRIPTION "The Time To Live in a PIM-DM Refresh message at which it is not forwarded on this interface." DEFVAL { 0 } ::= { myPimInterfaceEntry 18 } myPimInterfaceLanDelayEnabled OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION "Evaluates to TRUE if all routers on this interface are using the LAN Prune Delay Option." ::= { myPimInterfaceEntry 19 } myPimInterfaceSRCapable OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION "Evaluates to TRUE if all routers on this interface are using the State Refresh Capable Option." ::= { myPimInterfaceEntry 20 } myPimInterfaceDRPriority OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-write STATUS current DESCRIPTION "The Designater Router Priority inserted into the DR priority option on this interface." DEFVAL { 1 } ::= { myPimInterfaceEntry 21 } myPimInterfaceNbrCounter OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of interface's neighbour." ::= { myPimInterfaceEntry 22 } myPimInterfaceBsrBorderEnabled OBJECT-TYPE SYNTAX EnabledStatus MAX-ACCESS read-write STATUS current DESCRIPTION "Enabled means Define a PIM bootstrap message boundary for the PIM domain,use disabled to remove the PIM border." DEFVAL {disabled} ::= { myPimInterfaceEntry 23 } myPimInterfaceCountIn OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of packets into the interface since the router has been up." ::= { myPimInterfaceEntry 24 } myPimInterfaceCountOut OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "Number of packets out of the interface since the router has been up." ::= { myPimInterfaceEntry 25 } myPimInterfaceEnabled OBJECT-TYPE SYNTAX EnabledStatus MAX-ACCESS read-write STATUS current DESCRIPTION "use the ip pim command in interface configuration mode. To disable PIM on the interface, use the no form of this command." DEFVAL{disabled} ::= { myPimInterfaceEntry 26 } myPimNeighborFilterAcl OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-write STATUS current DESCRIPTION "The name of the neighbor filter address list,which limits the scope of the neighbor,The default value means all neighbors will be allowed." DEFVAL{""} ::= { myPimInterfaceEntry 27} myPimDrSupportAddressBound OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-write STATUS current DESCRIPTION "The name of the DR support address list,which limits the scope of the souce address ,this will be only used when the interface is DR, The default value means all souce address will be allowed." DEFVAL{""} ::= { myPimInterfaceEntry 28 } -- -- The PIM Neighbor Table -- myPimNeighborTable OBJECT-TYPE SYNTAX SEQUENCE OF MyPimNeighborEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The (conceptual) table listing the router's PIM neighbors." ::= { myPim 3 } myPimNeighborEntry OBJECT-TYPE SYNTAX MyPimNeighborEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry (conceptual row) in the myPimNeighborTable." INDEX { myPimNeighborAddress } ::= { myPimNeighborTable 1 } MyPimNeighborEntry ::= SEQUENCE { myPimNeighborAddress IpAddress, myPimNeighborIfIndex InterfaceIndex, myPimNeighborUpTime TimeTicks, myPimNeighborExpiryTime TimeTicks, myPimNeighborMode INTEGER, myPimNeighborLanPruneDelay Integer32, myPimNeighborOverrideInterval Integer32, myPimNeighborTBit Integer32, myPimNeighborSRCapable TruthValue, myPimNeighborDRPresent TruthValue } myPimNeighborAddress OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS not-accessible STATUS current DESCRIPTION "The IP address of the PIM neighbor for which this entry contains information." ::= { myPimNeighborEntry 1 } myPimNeighborIfIndex OBJECT-TYPE SYNTAX InterfaceIndex MAX-ACCESS read-only STATUS current DESCRIPTION "The value of ifIndex for the interface used to reach this PIM neighbor." ::= { myPimNeighborEntry 2 } myPimNeighborUpTime OBJECT-TYPE SYNTAX TimeTicks MAX-ACCESS read-only STATUS current DESCRIPTION "The time since this PIM neighbor (last) became a neighbor of the local router." ::= { myPimNeighborEntry 3 } myPimNeighborExpiryTime OBJECT-TYPE SYNTAX TimeTicks MAX-ACCESS read-only STATUS current DESCRIPTION "The minimum time remaining before this PIM neighbor will be aged out." ::= { myPimNeighborEntry 4 } myPimNeighborMode OBJECT-TYPE SYNTAX INTEGER { dense(1), sparse(2) } MAX-ACCESS read-only STATUS deprecated DESCRIPTION "The active PIM mode of this neighbor. This object is deprecated for PIMv2 routers since all neighbors on the interface must be either dense or sparse as determined by the protocol running on the interface." ::= { myPimNeighborEntry 5 } myPimNeighborLanPruneDelay OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The value of LAN Prune Delay field of the LAN Prune Delay Option received from this neighbor. A value of 0 indicates that no LAN Prune Delay Option was received from this neigbor." ::= { myPimNeighborEntry 6 } myPimNeighborOverrideInterval OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The value of Override Interval field of the LAN Prune Delay Option received from this neighbor. A value of 0 indicates that no LAN Prune Delay Option was received from this neigbor." ::= { myPimNeighborEntry 7 } myPimNeighborTBit OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The value of the T bit field of the LAN Prune Delay Option received from this neighbor. The T bit specifies the ability of the neighbor to disable join suppression." ::= { myPimNeighborEntry 8 } myPimNeighborSRCapable OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION "Evaluates to TRUE if this neighbor is using the State Refresh Capable Option." ::= { myPimNeighborEntry 9 } myPimNeighborDRPresent OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION "Evaluates to TRUE if this neighbor is using the Designated Router Option." ::= { myPimNeighborEntry 10 } -- -- The PIM IP Multicast Route Table -- myPimIpMRouteTable OBJECT-TYPE SYNTAX SEQUENCE OF MyPimIpMRouteEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The (conceptual) table listing PIM-specific information on a subset of the rows of the ipMRouteTable defined in the IP Multicast MIB." ::= { myPim 4 } myPimIpMRouteEntry OBJECT-TYPE SYNTAX MyPimIpMRouteEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry (conceptual row) in the pimIpMRouteTable. There is one entry per entry in the ipMRouteTable whose incoming interface is running PIM." INDEX { ipMRouteGroup, ipMRouteSource, ipMRouteSourceMask } ::= { myPimIpMRouteTable 1 } MyPimIpMRouteEntry ::= SEQUENCE { myPimIpMRouteUpstreamAssertTimer TimeTicks, myPimIpMRouteAssertMetric Integer32, myPimIpMRouteAssertMetricPref Integer32, myPimIpMRouteAssertRPTBit TruthValue, myPimIpMRouteFlags Integer32, myPimIpMRouteRPFNeighbor IpAddress, myPimIpMRouteSourceTimer TimeTicks, myPimIpMRouteOriginatorSRTTL Integer32 } myPimIpMRouteUpstreamAssertTimer OBJECT-TYPE SYNTAX TimeTicks MAX-ACCESS read-only STATUS current DESCRIPTION "The time remaining before the router changes its upstream neighbor back to its RPF neighbor. This timer is called the Assert timer in the PIM Sparse and Dense mode specification. A value of 0 indicates that no Assert has changed the upstream neighbor away from the RPF neighbor." ::= { myPimIpMRouteEntry 1 } myPimIpMRouteAssertMetric OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The metric advertised by the assert winner on the upstream interface, or 0 if no such assert is in received." ::= { myPimIpMRouteEntry 2 } myPimIpMRouteAssertMetricPref OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The preference advertised by the assert winner on the upstream interface, or 0 if no such assert is in effect." ::= { myPimIpMRouteEntry 3 } myPimIpMRouteAssertRPTBit OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-only STATUS current DESCRIPTION "The value of the RPT-bit advertised by the assert winner on the upstream interface, or false if no such assert is in effect." ::= { myPimIpMRouteEntry 4 } myPimIpMRouteFlags OBJECT-TYPE SYNTAX Integer32 { rpt(0), spt(1) } MAX-ACCESS read-only STATUS current DESCRIPTION "This object describes PIM-specific flags related to a multicast state entry. See the PIM Sparse Mode specification for the meaning of the RPT and SPT bits." ::= { myPimIpMRouteEntry 5 } myPimIpMRouteRPFNeighbor OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The IP Address of the current RPF neighbor. If there is an upstream Assert Winner, it will be the RPF neighbor. Otherwise, the RPF neighbor will be the next hop indicated by unicast routing." ::= { myPimIpMRouteEntry 6 } myPimIpMRouteSourceTimer OBJECT-TYPE SYNTAX TimeTicks MAX-ACCESS read-only STATUS current DESCRIPTION "The time before this router ceases originating State Refresh messages for this route." ::= { myPimIpMRouteEntry 7 } myPimIpMRouteOriginatorSRTTL OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The TTL used in State Refresh messages originated by this router for this route." ::= { myPimIpMRouteEntry 8 } -- -- The PIM Next Hop Table -- myPimIpMRouteNextHopTable OBJECT-TYPE SYNTAX SEQUENCE OF MyPimIpMRouteNextHopEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The (conceptual) table listing PIM-specific information on a subset of the rows of the ipMRouteNextHopTable defined in the IP Multicast MIB." ::= { myPim 5 } myPimIpMRouteNextHopEntry OBJECT-TYPE SYNTAX MyPimIpMRouteNextHopEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry (conceptual row) in the pimIpMRouteNextHopTable. There is one entry per entry in the ipMRouteNextHopTable whose interface is running PIM and whose ipMRouteNextHopState is pruned(1)." INDEX { ipMRouteNextHopGroup, ipMRouteNextHopSource, ipMRouteNextHopSourceMask, ipMRouteNextHopIfIndex, ipMRouteNextHopAddress } ::= { myPimIpMRouteNextHopTable 1 } MyPimIpMRouteNextHopEntry ::= SEQUENCE { myPimIpMRouteNextHopPruneReason INTEGER, myPimIpMRouteNextHopAssertWinner IpAddress, myPimIpMRouteNextHopAssertTimer TimeTicks, myPimIpMRouteNextHopAssertMetric Integer32, myPimIpMRouteNextHopAssertMetricPref Integer32, myPimIpMRouteNextHopJoinPruneTimer TimeTicks } myPimIpMRouteNextHopPruneReason OBJECT-TYPE SYNTAX INTEGER { other (1), prune (2), assert (3) } MAX-ACCESS read-only STATUS current DESCRIPTION "This object indicates why the downstream interface was pruned, whether in response to a PIM prune message or due to PIM Assert processing." ::= { myPimIpMRouteNextHopEntry 1 } myPimIpMRouteNextHopAssertWinner OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The IP Address of the Assert Winner." ::= { myPimIpMRouteNextHopEntry 2 } myPimIpMRouteNextHopAssertTimer OBJECT-TYPE SYNTAX TimeTicks MAX-ACCESS read-only STATUS current DESCRIPTION "The time remaining before the PIM router leaves the current Assert state. A value of 0 indicates that the router is in the No Info state." ::= { myPimIpMRouteNextHopEntry 3 } myPimIpMRouteNextHopAssertMetric OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The metric advertised by the Assert Winner." ::= { myPimIpMRouteNextHopEntry 4 } myPimIpMRouteNextHopAssertMetricPref OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The metric preference advertised by the Assert Winner." ::= { myPimIpMRouteNextHopEntry 5 } myPimIpMRouteNextHopJoinPruneTimer OBJECT-TYPE SYNTAX TimeTicks MAX-ACCESS read-only STATUS current DESCRIPTION "The time remaining before the PIM router reverts to default operation on this interface. PIM-SM will cease forwarding, PIM-DM will resume forwarding." ::= { myPimIpMRouteNextHopEntry 6 } -- -- The PIM RP-Set Table -- myPimRPSetTable OBJECT-TYPE SYNTAX SEQUENCE OF MyPimRPSetEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The (conceptual) table listing PIM information for candidate Rendezvous Points (RPs) for IP multicast groups. When the local router is the BSR, this information is obtained from received Candidate-RP-Advertisements. When the local router is not the BSR, this information is obtained from received RP-Set messages." ::= { myPim 6 } myPimRPSetEntry OBJECT-TYPE SYNTAX MyPimRPSetEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry (conceptual row) in the pimRPSetTable." INDEX { myPimRPSetComponent, myPimRPSetGroupAddress, myPimRPSetGroupMask, myPimRPSetAddress } ::= { myPimRPSetTable 1 } MyPimRPSetEntry ::= SEQUENCE { myPimRPSetGroupAddress IpAddress, myPimRPSetGroupMask IpAddress, myPimRPSetAddress IpAddress, myPimRPSetHoldTime Integer32, myPimRPSetExpiryTime TimeTicks, myPimRPSetComponent Integer32, myPimRPSetUpTime TimeTicks } myPimRPSetGroupAddress OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS not-accessible STATUS current DESCRIPTION "The IP multicast group address which, when combined with pimRPSetGroupMask, gives the group prefix for which this entry contains information about the Candidate-RP." ::= { myPimRPSetEntry 1 } myPimRPSetGroupMask OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS not-accessible STATUS current DESCRIPTION "The multicast group address mask which, when combined with pimRPSetGroupAddress, gives the group prefix for which this entry contains information about the Candidate-RP." ::= { myPimRPSetEntry 2 } myPimRPSetAddress OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS not-accessible STATUS current DESCRIPTION "The IP address of the Candidate-RP." ::= { myPimRPSetEntry 3 } myPimRPSetHoldTime OBJECT-TYPE SYNTAX Integer32 (0..255) UNITS "seconds" MAX-ACCESS read-only STATUS current DESCRIPTION "The holdtime of a Candidate-RP." ::= { myPimRPSetEntry 4 } myPimRPSetExpiryTime OBJECT-TYPE SYNTAX TimeTicks MAX-ACCESS read-only STATUS current DESCRIPTION "The minimum time remaining before the Candidate-RP will be declared down." ::= { myPimRPSetEntry 5 } myPimRPSetComponent OBJECT-TYPE SYNTAX Integer32 (1..255) MAX-ACCESS not-accessible STATUS current DESCRIPTION " A number uniquely identifying the component. Each protocol instance connected to a separate domain should have a different index value." ::= { myPimRPSetEntry 6 } myPimRPSetUpTime OBJECT-TYPE SYNTAX TimeTicks MAX-ACCESS read-only STATUS current DESCRIPTION " Length of time that this rp has been up." ::= { myPimRPSetEntry 7 } -- -- The PIM Component Table -- myPimComponentTable OBJECT-TYPE SYNTAX SEQUENCE OF MyPimComponentEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The (conceptual) table containing objects specific to a PIM domain. One row exists for each domain to which the router is connected. A PIM-SM domain is defined as an area of the network over which Bootstrap messages are forwarded. Typically, a PIM-SM router will be a member of exactly one domain. This table also supports, however, routers which may form a border between two PIM-SM domains and do not forward Bootstrap messages between them." ::= { myPim 7 } myPimComponentEntry OBJECT-TYPE SYNTAX MyPimComponentEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry (conceptual row) in the starPimComponentTable." INDEX { myPimComponentIndex } ::= { myPimComponentTable 1 } MyPimComponentEntry ::= SEQUENCE { myPimComponentIndex Integer32, myPimComponentBSRAddress IpAddress, myPimComponentBSRExpiryTime TimeTicks, myPimComponentCRPHoldTime Integer32, myPimComponentBSRUptime TimeTicks, myPimComponentBSRPriority Integer32, myPimComponentBSRHashMaskLength Integer32, myPimComponentBSRNextBsrMessage TimeTicks, myPimComponentNextCandRPAdv TimeTicks } myPimComponentIndex OBJECT-TYPE SYNTAX Integer32 (1..255) MAX-ACCESS not-accessible STATUS current DESCRIPTION "A number uniquely identifying the component. Each protocol instance connected to a separate domain should have a different index value. Routers that only support membership in a single PIM-SM domain should use a pimComponentIndex value of 1." ::= { myPimComponentEntry 1 } myPimComponentBSRAddress OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The IP address of the bootstrap router (BSR) for the local PIM region." ::= { myPimComponentEntry 2 } myPimComponentBSRExpiryTime OBJECT-TYPE SYNTAX TimeTicks MAX-ACCESS read-only STATUS current DESCRIPTION "The minimum time remaining before the bootstrap router in the local domain will be declared down. For candidate BSRs, this is the time until the component sends an RP-Set message. For other routers, this is the time until it may accept an RP-Set message from a lower candidate BSR." ::= { myPimComponentEntry 3 } myPimComponentCRPHoldTime OBJECT-TYPE SYNTAX Integer32 (0..255) UNITS "seconds" MAX-ACCESS read-create STATUS current DESCRIPTION "The holdtime of the component when it is a candidate RP in the local domain." ::= { myPimComponentEntry 4 } myPimComponentBSRUptime OBJECT-TYPE SYNTAX TimeTicks MAX-ACCESS read-only STATUS current DESCRIPTION "Length of time that this router has been up." ::= { myPimComponentEntry 5 } myPimComponentBSRPriority OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The Priority of Bsr." ::= { myPimComponentEntry 6 } myPimComponentBSRHashMaskLength OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "Length of a mask (32 bits maximum) that is to be ANDed with the group address before the hash function is called." ::= { myPimComponentEntry 7 } myPimComponentBSRNextBsrMessage OBJECT-TYPE SYNTAX TimeTicks MAX-ACCESS read-only STATUS current DESCRIPTION "Time (in hours, minutes, and seconds) in which the next bootstrap message is due from this BSR." ::= { myPimComponentEntry 8 } myPimComponentNextCandRPAdv OBJECT-TYPE SYNTAX TimeTicks MAX-ACCESS read-only STATUS current DESCRIPTION "Time (in hours, minutes, and seconds) in which the next candidate RP advertisement will be sent." ::= { myPimComponentEntry 9} -- -- PIM State Refresh Objects -- myPimSourceLifetime OBJECT-TYPE SYNTAX Integer32 UNITS "seconds" MAX-ACCESS read-write STATUS current DESCRIPTION "The maximum time this router will continue to originate State Refresh messages in the absence of traffic from the source itself." DEFVAL { 2100 } ::= { myPim 8 } myPimStateRefreshInterval OBJECT-TYPE SYNTAX Integer32 (1..255) UNITS "seconds" MAX-ACCESS read-write STATUS current DESCRIPTION "The interval between successive State Refresh messages originated by this router." DEFVAL { 60 } ::= { myPim 9 } myPimStateRefreshLimitInterval OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-write STATUS current DESCRIPTION "This router will not forward successive State Refresh messages received at less than this interval." DEFVAL { 0 } ::= { myPim 10 } myPimStateRefreshTimeToLive OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-write STATUS current DESCRIPTION "The TTL to be used by this router's originated State Refresh messages if the data packet's TTL is not recorded." DEFVAL { 16 } ::= { myPim 11 } myPimBsrCandidateGroup OBJECT IDENTIFIER ::= { myPim 12 } myPimBsrCandidateIfindex OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-write STATUS current DESCRIPTION "Interface type and number on this router from which the bootstrap router address is derived, to make it a candidate. This interface must be enabled with Protocol Independent Multicast (PIM)." ::= { myPimBsrCandidateGroup 1 } myPimBsrCandidateHashMaskLength OBJECT-TYPE SYNTAX Integer32(0..32) MAX-ACCESS read-write STATUS current DESCRIPTION "Length of a mask (32 bits maximum) that is to be ANDed with the group address before the hash function is called. All groups with the same seed hash (correspond) to the same RP. if myPimBsrCandidateIfindex is 0,then set this value is not valid." DEFVAL { 0 } ::= { myPimBsrCandidateGroup 2 } myPimBsrCandidatePriority OBJECT-TYPE SYNTAX Integer32(0..255) MAX-ACCESS read-write STATUS current DESCRIPTION "The BSR with the larger priority is preferred. If the priority values are the same, the router with the larger IP address is the BSR.if myPimBsrCandidateIfindex is 0,then set this value is not valid" DEFVAL { 0 } ::= { myPimBsrCandidateGroup 3 } myPimRPTable OBJECT-TYPE SYNTAX SEQUENCE OF MyPimRPEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The (conceptual) table listing PIM version 2 information for the Rendezvous Points (RPs) for IP multicast groups." ::= { myPim 13 } myPimRPEntry OBJECT-TYPE SYNTAX MyPimRPEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry (conceptual row) in the pimRPTable." INDEX { myPimRPGroupAddress } ::= { myPimRPTable 1 } MyPimRPEntry ::= SEQUENCE { myPimRPGroupAddress IpAddress, myPimRPAddress IpAddress, myPimRPExpiryTime TimeTicks, myPimRPNextRPReachableIn TimeTicks } myPimRPGroupAddress OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS not-accessible STATUS current DESCRIPTION "The IP multicast group address which, when combined with pimRPSetGroupMask, gives the group prefix for which this entry contains information about the Candidate-RP." ::= { myPimRPEntry 1 } myPimRPAddress OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The IP address of the RP." ::= { myPimRPEntry 2 } myPimRPExpiryTime OBJECT-TYPE SYNTAX TimeTicks MAX-ACCESS read-only STATUS current DESCRIPTION "The minimum time remaining before the RP will be declared down. If the local router is not the BSR, this value is 0." ::= { myPimRPEntry 3 } myPimRPNextRPReachableIn OBJECT-TYPE SYNTAX TimeTicks MAX-ACCESS read-only STATUS current DESCRIPTION "Indicates the time the next RP-reachable message will be sent. Time is expressed in hours:minutes:seconds." ::= { myPimRPEntry 4 } -- --static RP Table -- myPimStaticRPTable OBJECT-TYPE SYNTAX SEQUENCE OF MyPimStaticRPEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The (conceptual) table listing PIM version 2 information for the Rendezvous Points (RPs) for IP multicast groups." ::= { myPim 14 } myPimStaticRPEntry OBJECT-TYPE SYNTAX MyPimStaticRPEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry (conceptual row) in the pimStaticRPTable." INDEX { myPimStaticRPAddress } ::= { myPimStaticRPTable 1 } MyPimStaticRPEntry ::= SEQUENCE { myPimStaticRPAddress IpAddress, myPimStaticRPAddressIsOverride EnabledStatus, myPimStaticRPAclName DisplayString, myPimStaticRPStatus RowStatus } myPimStaticRPAddress OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS not-accessible STATUS current DESCRIPTION "The IP address of the RP." ::= { myPimStaticRPEntry 1 } myPimStaticRPAddressIsOverride OBJECT-TYPE SYNTAX EnabledStatus MAX-ACCESS read-create STATUS current DESCRIPTION "Indicates that if there is a conflict, the RP configured with this command prevails over the RP learned by Bsr-RP." DEFVAL { disabled } ::= { myPimStaticRPEntry 2 } myPimStaticRPAclName OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-create STATUS current DESCRIPTION "Name of an access list that defines for which multicast groups the RP should be used,the default value means all groups should be used." DEFVAL { "" } ::= { myPimStaticRPEntry 3 } myPimStaticRPStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "The status of this entry. Creating the entry enables PIM on the interface; destroying the entry disables PIM on the interface." ::= {myPimStaticRPEntry 4} myPimRpCandidateTable OBJECT-TYPE SYNTAX SEQUENCE OF MyPimRpCandidateEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The (conceptual) table listing the IP multicast groups for which the local router is to advertise itself as a Candidate-RP when the value of pimComponentCRPHoldTime is non-zero. If this table is empty, then the local router will advertise itself as a Candidate-RP for all groups (providing the value of pimComponentCRPHoldTime is non- zero)." ::= { myPim 15 } myPimRpCandidateEntry OBJECT-TYPE SYNTAX MyPimRpCandidateEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "An entry (conceptual row) in the pimRpCandidateTable." INDEX { myPimRpCandidateIfindex } ::= { myPimRpCandidateTable 1 } MyPimRpCandidateEntry ::= SEQUENCE { myPimRpCandidateIfindex InterfaceIndex, myPimRpCandidateAclName DisplayString, myPimRpCandidateStatus RowStatus } myPimRpCandidateIfindex OBJECT-TYPE SYNTAX InterfaceIndex MAX-ACCESS not-accessible STATUS current DESCRIPTION "IP address associated with this interface type and number is advertised as a candidate RP address." ::= { myPimRpCandidateEntry 1 } myPimRpCandidateAclName OBJECT-TYPE SYNTAX DisplayString MAX-ACCESS read-create STATUS current DESCRIPTION "The name of Acl list,that defines the group prefixes that are advertised in association with the RP address,the default value means all groups will be advertised in association with the RP address." DEFVAL { "" } ::= { myPimRpCandidateEntry 2 } myPimRpCandidateStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "The status of this entry. Creating the entry enables PIM on the interface; destroying the entry disables PIM on the interface." ::= {myPimRpCandidateEntry 3} -- PIM Traps myPimNeighborLoss NOTIFICATION-TYPE OBJECTS { myPimNeighborIfIndex } STATUS current DESCRIPTION "A pimNeighborLoss trap signifies the loss of an adjacency with a neighbor. This trap should be generated when the neighbor timer expires, and the router has no other neighbors on the same interface with a lower IP address than itself." ::= { myPimTraps 1 } END