-- ***************************************************************** -- MY-RIP-MIB.mib: My RIP MIB file -- -- $Copyright$ -- -- ***************************************************************** -- MY-RIP-MIB DEFINITIONS ::= BEGIN IMPORTS MODULE-IDENTITY, OBJECT-TYPE, NOTIFICATION-TYPE, Integer32, Counter32, IpAddress FROM SNMPv2-SMI VlanId FROM Q-BRIDGE-MIB TruthValue, DisplayString, RowStatus, MacAddress FROM SNMPv2-TC MODULE-COMPLIANCE, OBJECT-GROUP, NOTIFICATION-GROUP FROM SNMPv2-CONF ConfigStatus, MemberMap, IfIndex FROM MY-TC EnabledStatus FROM P-BRIDGE-MIB myMgmt FROM MY-SMI; myRIPMIB MODULE-IDENTITY LAST-UPDATED "200203200000Z" ORGANIZATION "$Company$" CONTACT-INFO " Tel: $Telephone$ E-mail: $E-mail$" DESCRIPTION "This module defines my Rip mibs." REVISION "200203200000Z" DESCRIPTION "Initial version of this MIB module." ::= { myMgmt 13} myRIPMIBObjects OBJECT IDENTIFIER ::= { myRIPMIB 1 } --- ---RIP GROUP --- myRipEnable OBJECT-TYPE SYNTAX EnabledStatus MAX-ACCESS read-write STATUS current DESCRIPTION "Rip management function status" DEFVAL { disabled } ::={ myRIPMIBObjects 1 } myRipUpdateTime OBJECT-TYPE SYNTAX Integer32 (0..2147483647) MAX-ACCESS read-write STATUS current DESCRIPTION "The rate (time in seconds between updates) at which routing updates are sent." DEFVAL {30} ::={ myRIPMIBObjects 2 } myRipInvalidTime OBJECT-TYPE SYNTAX Integer32 (1..2147483647) MAX-ACCESS read-write STATUS current DESCRIPTION "The interval of time (in seconds) after which a route is declared invalid." DEFVAL {180} ::={ myRIPMIBObjects 3 } myRipHolddownTime OBJECT-TYPE SYNTAX Integer32 (0..2147483647) MAX-ACCESS read-write STATUS current DESCRIPTION "The amount of time (in seconds) that must pass before a route is removed from the routing table" DEFVAL {120} ::={ myRIPMIBObjects 4 } myRipRecommendSetting OBJECT-TYPE SYNTAX INTEGER{ ripv1(1), ripv2(2), compatible(3) } MAX-ACCESS read-write STATUS current DESCRIPTION "User can set this object to 1,2,3. 1 means that the system sending and receiving RIP version1 packets, 2 means that the system sending and receiving RIP version2 packets, 3 means that the system sending RIP version1 packets and receiving both RIP version1 and RIP version2 packets. If the system RIP interface configuration has been modified by user,this object will be 4." DEFVAL {3} ::={myRIPMIBObjects 5} -- The RIP Interface Status Table. myRipIfStatTable OBJECT-TYPE SYNTAX SEQUENCE OF MyRipIfStatEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A list of subnets which require separate status monitoring in RIP." ::= { myRIPMIBObjects 6 } myRipIfStatEntry OBJECT-TYPE SYNTAX MyRipIfStatEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A Single Routing Domain in a single Subnet." INDEX { myRipIfStatIfIndex } ::= { myRipIfStatTable 1 } MyRipIfStatEntry ::= SEQUENCE { myRipIfStatIfIndex IfIndex, myRipIfStatRcvBadPackets Counter32, myRipIfStatRcvBadRoutes Counter32, myRipIfStatSentUpdates Counter32 } myRipIfStatIfIndex OBJECT-TYPE SYNTAX IfIndex MAX-ACCESS read-only STATUS current DESCRIPTION "VID of vlan which each net interface associate." ::= { myRipIfStatEntry 1 } myRipIfStatRcvBadPackets OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of RIP response packets received by the RIP process which were subsequently discarded for any reason (e.g. a version 0 packet, or an unknown command type)." ::= { myRipIfStatEntry 2 } myRipIfStatRcvBadRoutes OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of routes, in valid RIP packets, which were ignored for any reason (e.g. unknown address family, or invalid metric)." ::= { myRipIfStatEntry 3 } myRipIfStatSentUpdates OBJECT-TYPE SYNTAX Counter32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of triggered RIP updates actually sent on this interface. This explicitly does NOT include full updates sent containing new information." ::= { myRipIfStatEntry 4 } -- The RIP Interface Configuration Table. myRipIfConfTable OBJECT-TYPE SYNTAX SEQUENCE OF MyRipIfConfEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A list of interfaces which require separate configuration in RIP." ::= { myRIPMIBObjects 7 } myRipIfConfEntry OBJECT-TYPE SYNTAX MyRipIfConfEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A Single Routing Domain in a single interface." INDEX { myRipIfConfIfIndex } ::= { myRipIfConfTable 1 } MyRipIfConfEntry ::= SEQUENCE { myRipIfConfIfIndex IfIndex, myRipIfConfAuthType INTEGER, myRipIfConfAuthKeyChain OCTET STRING, myRipIfConfSend INTEGER, myRipIfConfReceive INTEGER, myRipIfPassiveStatus EnabledStatus, myRipIfBroadcastEnable EnabledStatus, myRipIfAdminStat EnabledStatus } myRipIfConfIfIndex OBJECT-TYPE SYNTAX IfIndex MAX-ACCESS read-only STATUS current DESCRIPTION "IfIndex vale of vlan interface." ::= { myRipIfConfEntry 1 } myRipIfConfAuthType OBJECT-TYPE SYNTAX INTEGER { noAuthentication(1), simplePassword (2), md5(3) } MAX-ACCESS read-write STATUS current DESCRIPTION "The type of Authentication used on this interface." DEFVAL { noAuthentication } ::= { myRipIfConfEntry 2 } myRipIfConfAuthKeyChain OBJECT-TYPE SYNTAX DisplayString(SIZE(1..32)) MAX-ACCESS read-write STATUS current DESCRIPTION "The key chain name which interface associated. It indicate that this interface doesn't match any key chain which this string is null" REFERENCE "myAuthenKeyChainName in MY-AUTHEN-KEY-MIB." ::= { myRipIfConfEntry 3 } myRipIfConfSend OBJECT-TYPE SYNTAX INTEGER { ripVersion1 (1), rip1Compatible (2), ripVersion2 (3) } MAX-ACCESS read-write STATUS current DESCRIPTION "What the router sends on this interface. ripVersion1 implies sending RIP updates compliant with RFC 1058. rip1Compatible implies broadcasting RIP-2 updates using RFC 1058 route subsumption rules. ripVersion2 implies multicasting RIP-2 updates. ripV1Demand indicates the use of Demand RIP on a WAN interface under RIP Version 1 rules. ripV2Demand indicates the use of Demand RIP on a WAN interface under Version 2 rules." DEFVAL { rip1Compatible } ::= { myRipIfConfEntry 4 } myRipIfConfReceive OBJECT-TYPE SYNTAX INTEGER { rip1 (1), rip2 (2), rip1OrRip2 (3) } MAX-ACCESS read-write STATUS current DESCRIPTION "This indicates which version of RIP updates are to be accepted. Note that rip2 and rip1OrRip2 implies reception of multicast packets." DEFVAL { rip1OrRip2 } ::= { myRipIfConfEntry 5 } myRipIfPassiveStatus OBJECT-TYPE SYNTAX EnabledStatus MAX-ACCESS read-write STATUS current DESCRIPTION " The interface will not send routing updates if this value is 'enabled'" DEFVAL { disabled } ::={ myRipIfConfEntry 6 } myRipIfBroadcastEnable OBJECT-TYPE SYNTAX EnabledStatus MAX-ACCESS read-write STATUS current DESCRIPTION "Enable or disable broadcast updats of RIP in this interface" DEFVAL { disabled } ::={ myRipIfConfEntry 7 } myRipIfAdminStat OBJECT-TYPE SYNTAX EnabledStatus MAX-ACCESS read-only STATUS current DESCRIPTION "The RIP interface's administrative status. The value formed on the interface, and the in- terface will be advertised as an internal route to some area. The value 'disabled' denotes that the interface is external to RIP." ::= { myRipIfConfEntry 8 } myRipOffsetMetric OBJECT-TYPE SYNTAX Integer32 (1..15) MAX-ACCESS read-write STATUS current DESCRIPTION "This object means the value of increasing incoming and outgoing metrics to routes learned via RIP " DEFVAL {1} ::={ myRIPMIBObjects 8 } myRipAdministrativeDistance OBJECT-TYPE SYNTAX Integer32 (0..255) MAX-ACCESS read-write STATUS current DESCRIPTION "This object specified the priority of route information learned via RIP." ::={ myRIPMIBObjects 9} myRipValidateUpdateSrcEnable OBJECT-TYPE SYNTAX EnabledStatus MAX-ACCESS read-write STATUS current DESCRIPTION "This object allow of enabling or disabling validate the source IP address of incoming RIP routing updates." DEFVAL { enabled } ::={ myRIPMIBObjects 10 } myRipPassiveStatus OBJECT-TYPE SYNTAX EnabledStatus MAX-ACCESS read-write STATUS current DESCRIPTION "The myRipIfPassiveStatus of a interface equal to this object value when this interface is created. If you change this object value to 'enabled' or 'disabled'all interfaces which have exist will also change their myRipIfPassiveStatus to 'enabled' or 'disabled'." DEFVAL { disabled } ::={ myRIPMIBObjects 11 } myRipNextDueIn OBJECT-TYPE SYNTAX TimeTicks MAX-ACCESS read-only STATUS current DESCRIPTION "Waitting time interval before next update packet generatting in units of second" ::={ myRIPMIBObjects 12 } -- The RIP Interface Offset Table. myRipIfOffsetTable OBJECT-TYPE SYNTAX SEQUENCE OF MyRipIfOffsetEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The interface configuration about offset. Apply an offset list to routing metrics to increase incoming and outgoing metrics to routes learned through RIP. You can limit the offset list with an access list or an interface." ::= { myRIPMIBObjects 13 } myRipIfOffsetEntry OBJECT-TYPE SYNTAX MyRipIfOffsetEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "the entry of this table." INDEX { myRipIfOffsetIfIndex,myRipIfOffsetMethod } ::= { myRipIfOffsetTable 1 } MyRipIfOffsetEntry ::= SEQUENCE { myRipIfOffsetIfIndex Integer32, myRipIfOffsetMethod INTEGER, myRipIfOffsetAclName DisplayString, myRipIfOffsetMetric Unsigned32, myRipIfOffsetStatus RowStatus } myRipIfOffsetIfIndex OBJECT-TYPE SYNTAX Integer32 (0..2147483647) MAX-ACCESS read-only STATUS current DESCRIPTION "the interface that this offset list apply to. If this value is 0,it indicate that this offset list apply in all interfaces except the interfaceswhich which have not Offset configure. Other value is equal to TEXTUAL-CONVENTION IfIndex meaning,this offset list will apply in only the designate interface" ::= { myRipIfOffsetEntry 1 } myRipIfOffsetMethod OBJECT-TYPE SYNTAX INTEGER{ out(1), in(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "the offset list apply to incoming routes or outgoing routes." ::= { myRipIfOffsetEntry 2 } myRipIfOffsetAclName OBJECT-TYPE SYNTAX DisplayString(SIZE(1..32)) MAX-ACCESS read-write STATUS current DESCRIPTION " the offset list with Access list name ." ::= { myRipIfOffsetEntry 3 } myRipIfOffsetMetric OBJECT-TYPE SYNTAX Unsigned32(0..16) MAX-ACCESS read-write STATUS current DESCRIPTION "the offset list with offset value, in condition the value will be added to route metric." ::= { myRipIfOffsetEntry 4 } myRipIfOffsetStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION " if this value is setted destroy, the entry will be deleted ." ::= { myRipIfOffsetEntry 5 } --network table myRipNetworkTable OBJECT-TYPE SYNTAX SEQUENCE OF MyRipNetworkEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "the network for rip routing." ::= { myRIPMIBObjects 14 } myRipNetworkEntry OBJECT-TYPE SYNTAX MyRipNetworkEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "the entry of this table." INDEX { myRipNetworkAddr } ::= { myRipNetworkTable 1 } MyRipNetworkEntry ::= SEQUENCE { myRipNetworkAddr IpAddress, myRipNetworkMask IpAddress, myRipNetworkStatus RowStatus } myRipNetworkAddr OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "define a network for rip routing ." ::= { myRipNetworkEntry 1 } myRipNetworkMask OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "define a network's mask for rip routing ." ::= { myRipNetworkEntry 2 } myRipNetworkStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "if destroy is setted, this entry will be deleted ." ::= { myRipNetworkEntry 3 } --neighbor table myRipNeighborTable OBJECT-TYPE SYNTAX SEQUENCE OF MyRipNeighborEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "the neighbor for rip routing." ::= { myRIPMIBObjects 15 } myRipNeighborEntry OBJECT-TYPE SYNTAX MyRipNeighborEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "the entry of this table." INDEX { myRipNeighborIndex } ::= { myRipNeighborTable 1 } MyRipNeighborEntry ::= SEQUENCE { myRipNeighborIndex IpAddress, myRipNeighborStatus RowStatus } myRipNeighborIndex OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "define a neighbor for rip ." ::= { myRipNeighborEntry 1 } myRipNeighborStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "if destroy is setted, this entry will be deleted." ::= { myRipNeighborEntry 2 } myRIPMIBConformance OBJECT IDENTIFIER ::= { myRIPMIB 2 } myRIPMIBCompliances OBJECT IDENTIFIER ::= { myRIPMIBConformance 1 } myRIPMIBGroups OBJECT IDENTIFIER ::= { myRIPMIBConformance 2 } -- compliance statements myRIPMIBCompliance MODULE-COMPLIANCE STATUS current DESCRIPTION "The compliance statement for entities which implement the My Snooping Dhcp MIB" MODULE -- this module MANDATORY-GROUPS { myRipMIBGroup, myRIPExtendMIBGroup } ::= { myRIPMIBCompliances 1 } -- units of conformance myRipMIBGroup OBJECT-GROUP OBJECTS { myRipEnable, myRipUpdateTime, myRipInvalidTime, myRipHolddownTime, myRipRecommendSetting, myRipIfStatIfIndex, myRipIfStatRcvBadPackets, myRipIfStatRcvBadRoutes, myRipIfStatSentUpdates, myRipIfConfIfIndex, myRipIfConfAuthType, myRipIfConfAuthKeyChain, myRipIfConfSend, myRipIfConfReceive, myRipIfPassiveStatus, myRipIfBroadcastEnable, myRipIfAdminStat, myRipOffsetMetric, myRipAdministrativeDistance, myRipValidateUpdateSrcEnable } STATUS current DESCRIPTION "A collection of objects providing rip managment." ::= { myRIPMIBGroups 1 } myRIPExtendMIBGroup OBJECT-GROUP OBJECTS { myRipNextDueIn, myRipIfOffsetIfIndex, myRipIfOffsetMethod, myRipIfOffsetAclName, myRipIfOffsetMetric, myRipIfOffsetStatus, myRipNetworkAddr, myRipNetworkMask, myRipNetworkStatus, myRipNeighborIndex, myRipNeighborStatus } STATUS current DESCRIPTION "A collection of objects providing rip extend managment." ::= { myRIPMIBGroups 2 } END