-- ***************************************************************** -- MY-ROUTE-MIB.mib: My Route MIB file -- -- $Copyright$ -- -- ***************************************************************** -- MY-ROUTE-MIB DEFINITIONS ::= BEGIN IMPORTS MODULE-IDENTITY, OBJECT-TYPE, NOTIFICATION-TYPE, Integer32, Counter32, IpAddress FROM SNMPv2-SMI VlanId FROM Q-BRIDGE-MIB TruthValue, DisplayString, RowStatus, MacAddress FROM SNMPv2-TC MODULE-COMPLIANCE, OBJECT-GROUP, NOTIFICATION-GROUP FROM SNMPv2-CONF ConfigStatus, IfIndex FROM MY-TC EnabledStatus FROM P-BRIDGE-MIB BigMetric FROM OSPF-MIB myMgmt FROM MY-SMI; myRouteMIB MODULE-IDENTITY LAST-UPDATED "200203200000Z" ORGANIZATION "$Company$" CONTACT-INFO " Tel: $Telephone$ E-mail: $E-mail$" DESCRIPTION "This module defines my route mibs." REVISION "200203200000Z" DESCRIPTION "Initial version of this MIB module." ::= { myMgmt 20} MyRouteProtoType ::= TEXTUAL-CONVENTION STATUS current DESCRIPTION "Routing protocol type." SYNTAX INTEGER { other(1), --notspecified local(2), --localinterface netmgmt(3), --staticroute icmp(4), --resultofICMPRedirect egp(5), --ExteriorGatewayProtocol ggp(6), --Gateway-GatewayProtocol hello(7), --FuzzBallHelloSpeak rip(8), --BerkeleyRIPorRIP-II isis(9), --DualIS-IS esis(10), --ISO9542 ciscoigrp(11), --CiscoIGRP bbnspfigp(12), --BBNSPFIGP ospf(13), --OpenShortestPathFirst bgp(14), --BorderGatewayProtocol idpr(15), --InterDomainPolicyRouting ciscoeigrp(16), --CiscoEIGRP max(17) --MAXTYPE } myRouteMIBObjects OBJECT IDENTIFIER ::= { myRouteMIB 1 } myRouteServiceStatus OBJECT-TYPE SYNTAX EnabledStatus MAX-ACCESS read-write STATUS current DESCRIPTION "Route management function status" ::={ myRouteMIBObjects 1 } myRoutingProtoInfoTable OBJECT-TYPE SYNTAX SEQUENCE OF MyRoutingProtoInfoEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The routing protocol infomation ." ::= { myRouteMIBObjects 2 } myRoutingProtoInfoEntry OBJECT-TYPE SYNTAX MyRoutingProtoInfoEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "the entry of this table." INDEX { myRoutingProtoInfoProtoType, myRoutingProtoInfoGateWay } ::= { myRoutingProtoInfoTable 1 } MyRoutingProtoInfoEntry ::= SEQUENCE{ myRoutingProtoInfoProtoType MyRouteProtoType, myRoutingProtoInfoGateWay IpAddress, myRoutingProtoInfoDistance Unsigned32, myRoutingProtoInfoLastUpdate TimeTicks } myRoutingProtoInfoProtoType OBJECT-TYPE SYNTAX MyRouteProtoType MAX-ACCESS read-only STATUS current DESCRIPTION "The routing protocol type" ::= { myRoutingProtoInfoEntry 1 } myRoutingProtoInfoGateWay OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "For rip ,the gateway is this router's neighbor. for ospf ,the gateway is the router Id of this router, New entry will be addded when router ID is changed." ::= { myRoutingProtoInfoEntry 2 } myRoutingProtoInfoDistance OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "The routing protocol distance." ::= { myRoutingProtoInfoEntry 3 } myRoutingProtoInfoLastUpdate OBJECT-TYPE SYNTAX TimeTicks MAX-ACCESS read-only STATUS current DESCRIPTION "The last update time of the neighbor that be found. or router ID that it last change ." ::= { myRoutingProtoInfoEntry 4 } myDefRoutingCfgTable OBJECT-TYPE SYNTAX SEQUENCE OF MyDefRoutingCfgEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Default routing configuration." ::= { myRouteMIBObjects 3} myDefRoutingCfgEntry OBJECT-TYPE SYNTAX MyDefRoutingCfgEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "The entry define one routing protocol's default routing configurate,if in rip routing configuration only route map is valid to this default route parameter" INDEX { myDefRoutingCfgRoutingProtoType} ::= { myDefRoutingCfgTable 1 } MyDefRoutingCfgEntry ::= SEQUENCE { myDefRoutingCfgRoutingProtoType MyRouteProtoType, myDefRoutingCfgAlways TruthValue, myDefRoutingCfgMetric Unsigned32, myDefRoutingCfgMetricType --only use in ospf INTEGER, myDefRoutingCfgRouteMap DisplayString, myDefRoutingCfgStatus RowStatus } myDefRoutingCfgRoutingProtoType OBJECT-TYPE SYNTAX MyRouteProtoType MAX-ACCESS read-only STATUS current DESCRIPTION "index indicate that which routing protocol configuration mode is current mode." ::= { myDefRoutingCfgEntry 1 } myDefRoutingCfgAlways OBJECT-TYPE SYNTAX TruthValue MAX-ACCESS read-create STATUS current DESCRIPTION "Setting the value to TRUE indicates that always advertise default route." DEFVAL{false} ::= { myDefRoutingCfgEntry 2 } myDefRoutingCfgMetric OBJECT-TYPE SYNTAX Unsigned32(1..16777214) MAX-ACCESS read-create STATUS current DESCRIPTION "Set ospf default metric value." DEFVAL {10} ::= { myDefRoutingCfgEntry 3 } myDefRoutingCfgMetricType OBJECT-TYPE SYNTAX INTEGER{ type1(1), type2(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "Set OSPF Link State type,this value is only valid in ospf configuration" DEFVAL {type2} ::= { myDefRoutingCfgEntry 4 } myDefRoutingCfgRouteMap OBJECT-TYPE SYNTAX DisplayString(SIZE(0..32)) MAX-ACCESS read-create STATUS current DESCRIPTION "Set route's Route-map reference.Null string indicate that no any route-map reference." DEFVAL {""} ::= { myDefRoutingCfgEntry 5 } myDefRoutingCfgStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "if this value is change to destroy, this entry will be deleted" ::= { myDefRoutingCfgEntry 6 } --Route map group myRouteMapMIBObjects OBJECT IDENTIFIER ::= { myRouteMIB 2 } --myRouteMapTable myRouteMapTable OBJECT-TYPE SYNTAX SEQUENCE OF MyRouteMapEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "the route map table." ::= { myRouteMapMIBObjects 1 } myRouteMapEntry OBJECT-TYPE SYNTAX MyRouteMapEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "the entry of this table." INDEX { myRouteMapName, myRouteMapSequenceNumber } ::= { myRouteMapTable 1 } MyRouteMapEntry ::= SEQUENCE{ myRouteMapName DisplayString, myRouteMapSequenceNumber Unsigned32, myRouteMapOperType INTEGER, myRouteMapMatchMetric Unsigned32, myRouteMapMatchRouteType INTEGER, myRouteMapMetricValueType INTEGER, myRouteMapSetMetric Unsigned32, myRouteMapSetLevel INTEGER, myRouteMapSetMetricType INTEGER, myRouteMapSetNexthopSt ConfigStatus, myRouteMapSetNexthop IpAddress, myRouteMapStatus RowStatus } myRouteMapName OBJECT-TYPE SYNTAX DisplayString(SIZE(1..32)) MAX-ACCESS read-only STATUS current DESCRIPTION "The route map name ,A meaningful name for the route map. The redistribute router configuration command uses this name to reference the route map. Multiple route maps might share the same map tag name. When this string be used as an index,Value of a sub-identifier equal ASCII value of corresponding character(first sub-identifier corresponds first character of string). The number of sub-identifiers of this string must be 32,If length of string is less than 32 the sub-identifier(0x0) will be filled in tail." ::= { myRouteMapEntry 1 } myRouteMapSequenceNumber OBJECT-TYPE SYNTAX Unsigned32(0..65535) MAX-ACCESS read-only STATUS current DESCRIPTION "Number that indicates the position of a new route map in the list of route maps already configured with the same name." DEFVAL {10} ::= { myRouteMapEntry 2 } myRouteMapOperType OBJECT-TYPE SYNTAX INTEGER { permit(1), deny(2) } MAX-ACCESS read-only STATUS current DESCRIPTION " If permit is specified and the match criteria are met for this route map, the route is redistributed as controlled by the set actions. If deny is specified, the route is not redistributed. " DEFVAL {permit} ::= { myRouteMapEntry 3 } myRouteMapMatchMetric OBJECT-TYPE SYNTAX Unsigned32(0..2147483647) MAX-ACCESS read-create STATUS current DESCRIPTION " Match the specified route metric. The metric-value can be an IGRP 5-part metric with a value from 1 to 255. 0 indicate that this item will not be matched." DEFVAL {0} ::= { myRouteMapEntry 4 } myRouteMapMatchRouteType OBJECT-TYPE SYNTAX INTEGER{ notMatch(0), internal(1), external(2), external-type1(3), external-type2(4) } MAX-ACCESS read-create STATUS current DESCRIPTION " the route type value which route-map match, internal: OSPF intra-area and interarea routes or EIGRP internal routes, external: OSPF external routes(Type 1 or Type 2)or EIGRP external routes, external-type1: OSPF external routes Type 1 external-type2: OSPF external routes Type 2 'notMatch' indicate that this item will not be matched." DEFVAL {notMatch} ::= { myRouteMapEntry 5} myRouteMapMetricValueType OBJECT-TYPE SYNTAX INTEGER{ noOper(0), replace(1), add(2), reduce(3) } MAX-ACCESS read-create STATUS current DESCRIPTION " How to modify old metric vlaue. 'noOper': metric value will not be modified. 'replace': old metric value will be replaced by myRouteMapSetMetric. 'add': new metric value will equal 'old metric vlaue + myRouteMapSetMetric' 'reduce': new metric value will equal 'old metric vlaue - myRouteMapSetMetric'" DEFVAL {noOper} ::= { myRouteMapEntry 6 } myRouteMapSetMetric OBJECT-TYPE SYNTAX Unsigned32(1..2147483647) MAX-ACCESS read-create STATUS current DESCRIPTION " Set the metric value to the given redistributed routes (for any protocol except IGRP or EIGRP). The metric value is an integer from 1 to 255. myRouteMapMetricValueType will decide real operation. The value of myRouteMapSetMetric is invalid in myRouteMapMetricValueType is 'noOper'." DEFVAL {1} ::= { myRouteMapEntry 7 } myRouteMapSetLevel OBJECT-TYPE SYNTAX INTEGER{ all(0), stubarea(1), -- OSPF NSSA backbone(2) -- OSPF backbone areas } MAX-ACCESS read-create STATUS current DESCRIPTION "Set the level for routes that are advertised into the specified area of the routing domain. 'all'indicate that routes will be advertised into all type area." DEFVAL {all} ::= { myRouteMapEntry 8 } myRouteMapSetMetricType OBJECT-TYPE SYNTAX INTEGER{ noOper(0), internal(1), external(2), type1(3), type2(4) } MAX-ACCESS read-create STATUS current DESCRIPTION " set metric type, 'external' means IS-IS external metric; 'internal' means Use IGP metric as the MED for BGP; 'type-1 ' means OSPF external type 1 metric; 'type-2 ' means OSPF external type 2 metric. 'noOper'indicate that no any opertion will be done for this item." DEFVAL {noOper} ::= { myRouteMapEntry 9} myRouteMapSetNexthopSt OBJECT-TYPE SYNTAX ConfigStatus MAX-ACCESS read-write STATUS current DESCRIPTION " How to modify nexthop vlaue. 'invalid': nexthop value will not be modified. 'valid': nexthop value will be modified to myRouteMapSetNexthop. Setting this value to 'valid' have no any effect.This value will be changed to 'valid' when setting 'myRouteMapSetNexthop'" DEFVAL {invalid} ::= { myRouteMapEntry 10 } myRouteMapSetNexthop OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-create STATUS current DESCRIPTION " Set the nexthop value to give the redistributed routes" ::= { myRouteMapEntry 11 } myRouteMapStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION " if this value is destroy,the entry will be delete." ::= { myRouteMapEntry 12 } --myRouteMapMatchIpAddressTable myRouteMapMatchIpAddressTable OBJECT-TYPE SYNTAX SEQUENCE OF MyRouteMapMatchIpAddressEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "the match ip address item of the route map ." ::= { myRouteMapMIBObjects 2 } myRouteMapMatchIpAddressEntry OBJECT-TYPE SYNTAX MyRouteMapMatchIpAddressEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Match a standard access list by specifying the Acl name " INDEX { myRouteMapName, myRouteMapSequenceNumber, myRouteMapMatchType, myRouteMapMatchIpAddressAclName } ::= { myRouteMapMatchIpAddressTable 1 } MyRouteMapMatchIpAddressEntry ::= SEQUENCE{ myRouteMapMatchType INTEGER, myRouteMapMatchIpAddressAclName DisplayString, myRouteMapMatchIpAddressStatus RowStatus } myRouteMapMatchType OBJECT-TYPE SYNTAX INTEGER{ destination(1), nextHop(2), source(3) } MAX-ACCESS read-only STATUS current DESCRIPTION "destination(1):match route destination ip address nextHop(2):match route nextHop ip address source(3):match route source ip address " ::= { myRouteMapMatchIpAddressEntry 1 } myRouteMapMatchIpAddressAclName OBJECT-TYPE SYNTAX DisplayString(SIZE(1..32)) MAX-ACCESS read-only STATUS current DESCRIPTION "The acl name apply to ip address. When this string be used as an index,Value of a sub-identifier equal ASCII value of corresponding character(first sub-identifier corresponds first character of string). The number of sub-identifiers of this string must be 32,If length of string is less than 32 the sub-identifier(0x0) will be filled in tail." ::= { myRouteMapMatchIpAddressEntry 2 } myRouteMapMatchIpAddressStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "The entry status,if the value is destroy ,the entry will be deleted." ::= { myRouteMapMatchIpAddressEntry 3 } --myRouteMapMatchTagTable myRouteMapMatchTagTable OBJECT-TYPE SYNTAX SEQUENCE OF MyRouteMapMatchTagEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Match a tag value item of route map " ::= { myRouteMapMIBObjects 3 } myRouteMapMatchTagEntry OBJECT-TYPE SYNTAX MyRouteMapMatchTagEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Match the specified tag value in a list of one or more route tag values. Each can be an integer from 0 to 4294967295. " INDEX { myRouteMapName, myRouteMapSequenceNumber, myRouteMapMatchTagValue } ::= { myRouteMapMatchTagTable 1 } MyRouteMapMatchTagEntry ::= SEQUENCE{ myRouteMapMatchTagValue Unsigned32, myRouteMapMatchTagStatus RowStatus } myRouteMapMatchTagValue OBJECT-TYPE SYNTAX Unsigned32(0..2147483647) MAX-ACCESS read-only STATUS current DESCRIPTION " Match the specified tag value." ::= { myRouteMapMatchTagEntry 1 } myRouteMapMatchTagStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION " the entry status,if the value is destroy ,the entry will be deleted." ::= { myRouteMapMatchTagEntry 2 } --myRouteMapMatchInterfaceTable myRouteMapMatchInterfaceTable OBJECT-TYPE SYNTAX SEQUENCE OF MyRouteMapMatchInterfaceEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Match Interface item of route map ." ::= { myRouteMapMIBObjects 4 } myRouteMapMatchInterfaceEntry OBJECT-TYPE SYNTAX MyRouteMapMatchInterfaceEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "Match the specified next hop route out one of the specified interfaces. " INDEX { myRouteMapName, myRouteMapSequenceNumber, myRouteMapMatchInterfaceIfIndex } ::= { myRouteMapMatchInterfaceTable 1 } MyRouteMapMatchInterfaceEntry ::= SEQUENCE{ myRouteMapMatchInterfaceIfIndex IfIndex, myRouteMapMatchInterfaceStatus RowStatus } myRouteMapMatchInterfaceIfIndex OBJECT-TYPE SYNTAX IfIndex MAX-ACCESS read-only STATUS current DESCRIPTION " The ifTable's ifIndex." ::= { myRouteMapMatchInterfaceEntry 1 } myRouteMapMatchInterfaceStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION " the entry status,if the value is destroy ,the entry will be deleted." ::= { myRouteMapMatchInterfaceEntry 2 } --Route redistribute group myRouteRedistributeMIBObjects OBJECT IDENTIFIER ::= { myRouteMIB 3 } --Routing Redistribute table myRouteRedistributeTable OBJECT-TYPE SYNTAX SEQUENCE OF MyRouteRedistributeEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION " this table descripts the redistributing methods." ::= { myRouteRedistributeMIBObjects 1 } myRouteRedistributeEntry OBJECT-TYPE SYNTAX MyRouteRedistributeEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "each entry descripts the methord,when Redistribute routes from one routing protocol to another routing protocol." INDEX {myRouteRedistributeProtocolCfg, myRouteRedistributeProtocol } ::= { myRouteRedistributeTable 1 } MyRouteRedistributeEntry ::= SEQUENCE{ myRouteRedistributeProtocolCfg MyRouteProtoType, myRouteRedistributeProtocol MyRouteProtoType, myRouteRedistributeMetricValue Unsigned32, myRouteRedistributeMetricType INTEGER, myRouteRedistributeTagValue Unsigned32, myRouteRedistributeRouteMapName DisplayString, myRouteRedistributeStatus RowStatus } myRouteRedistributeProtocolCfg OBJECT-TYPE SYNTAX MyRouteProtoType MAX-ACCESS read-only STATUS current DESCRIPTION "The protocol which the redistributing will be setted in." ::={myRouteRedistributeEntry 1} myRouteRedistributeProtocol OBJECT-TYPE SYNTAX MyRouteProtoType MAX-ACCESS read-only STATUS current DESCRIPTION "The protocol which routing will redistribute to ." ::={myRouteRedistributeEntry 2} myRouteRedistributeMetricValue OBJECT-TYPE SYNTAX Unsigned32(1..16777214) MAX-ACCESS read-create STATUS current DESCRIPTION "0 indicate that redistributing metric value will equal myOspfRouteRedisDefMetricVal for OSPF or myRipOffsetMetric for RIP. Other value indicate that myRouteRedistributeMetricValue will be set for new metric value for redistribute routes,for rip this value only can be from 1 to 16." DEFVAL {0} ::= { myRouteRedistributeEntry 3 } myRouteRedistributeMetricType OBJECT-TYPE SYNTAX INTEGER{ type1(1), type2(2) } MAX-ACCESS read-create STATUS current DESCRIPTION " Metric type value ." DEFVAL {type2} ::= { myRouteRedistributeEntry 4 } myRouteRedistributeTagValue OBJECT-TYPE SYNTAX Unsigned32(0..4294967295) MAX-ACCESS read-create STATUS current DESCRIPTION " Set tag for routes redistributed into OSPF." DEFVAL {0} ::= { myRouteRedistributeEntry 5 } myRouteRedistributeRouteMapName OBJECT-TYPE SYNTAX DisplayString(SIZE(0..32)) MAX-ACCESS read-create STATUS current DESCRIPTION "Set route's Route-map reference.Null string indicate that no any route-map reference." DEFVAL {""} ::= { myRouteRedistributeEntry 6 } myRouteRedistributeStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION " the entry status,if the value is destroy ,then disable this redistribute." ::= { myRouteRedistributeEntry 7 } myRouteFilteringMIBObjects OBJECT IDENTIFIER ::= { myRouteMIB 4 } --ip prefix-list table myIpPrefixListTable OBJECT-TYPE SYNTAX SEQUENCE OF MyIpPrefixListEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION " this table descripts the ip prefix list." ::= { myRouteFilteringMIBObjects 1 } myIpPrefixListEntry OBJECT-TYPE SYNTAX MyIpPrefixListEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "each entry descripts a prefix list" INDEX {myIpPrefixListName, myIpPrefixListSequence } ::= { myIpPrefixListTable 1 } MyIpPrefixListEntry ::= SEQUENCE{ myIpPrefixListName DisplayString, myIpPrefixListSequence Unsigned32, myIpPrefixListOperMethod INTEGER, myIpPrefixListIpAddress IpAddress, myIpPrefixListMaskLength Unsigned32, myIpPrefixListMinimumPrefixLength Unsigned32, myIpPrefixListMaximumPrefixLength Unsigned32, myIpPrefixListStatus RowStatus } myIpPrefixListName OBJECT-TYPE SYNTAX DisplayString(SIZE(1..32)) MAX-ACCESS read-only STATUS current DESCRIPTION "name of ip prefix-list name." ::={myIpPrefixListEntry 1} myIpPrefixListSequence OBJECT-TYPE SYNTAX Unsigned32(0..2147483647) MAX-ACCESS read-only STATUS current DESCRIPTION "sequence can be set either automatically or manually. if 0 is seted,that means sequence will be created automatically. In the case that sequential numbers are set manually, the user may pick any number less than 2147483647 and more than 1. In the case that sequential number are set automatically, the sequential number will increase by a unit of five (5) per list. If a list with no specified sequential number is created after a list with a specified sequential number, the list will automatically pick the next multiple of five (5) as the list number. For example, if a list with number 2 already exists and a new list with no specified number is created, the next list will be numbered 5. If lists 2 and 7 already exist and a new list with no specified number is created, the new list will be numbered 10." ::={myIpPrefixListEntry 2} myIpPrefixListOperMethod OBJECT-TYPE SYNTAX INTEGER{ permit(1), deny(2) } MAX-ACCESS read-write STATUS current DESCRIPTION "this field specifies whether the prefix for this entry is to permit or deny the listed prefix." ::={myIpPrefixListEntry 3} myIpPrefixListIpAddress OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-write STATUS current DESCRIPTION "ip prefix-list ip address." ::={myIpPrefixListEntry 4} myIpPrefixListMaskLength OBJECT-TYPE SYNTAX Unsigned32(0..32) MAX-ACCESS read-write STATUS current DESCRIPTION "ip prefix-list mask length." ::={myIpPrefixListEntry 5} myIpPrefixListMinimumPrefixLength OBJECT-TYPE SYNTAX Unsigned32(0..32) MAX-ACCESS read-write STATUS current DESCRIPTION "this field specifies prefix length. The prefix list will be applied if the prefix length is greater than or equal to myIpPrefixListMinimumPrefixLength. value '0' means that this parameter has no effect. The condition 'myIpPrefixListMaximumPrefixLength >= myIpPrefixListMinimumPrefixLength > myIpPrefixListMaskLength' must be satisfied when this value is not '0' " ::={myIpPrefixListEntry 6} myIpPrefixListMaximumPrefixLength OBJECT-TYPE SYNTAX Unsigned32(0..32) MAX-ACCESS read-write STATUS current DESCRIPTION "this field specifies prefix length. The prefix list will be applied if the prefix length is less than or equal to myIpPrefixListMaximumPrefixLength. value '0' means that this parameter has no effect. The condition 'myIpPrefixListMaximumPrefixLength >= myIpPrefixListMinimumPrefixLength > myIpPrefixListMaskLength' must be satisfied when this value is not '0' " ::={myIpPrefixListEntry 7} myIpPrefixListStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "the entry status,if the value is destroy ,then delete this ip prefix-list." ::={myIpPrefixListEntry 8} --distribute-list table --distribute-list is used for Filtering both input and output of the routing information myDistributeListTable OBJECT-TYPE SYNTAX SEQUENCE OF MyDistributeListEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION " this table descripts the distribute list." ::= { myRouteFilteringMIBObjects 2 } myDistributeListEntry OBJECT-TYPE SYNTAX MyDistributeListEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "distribute-list can be applied to both incoming and outgoing routing information,Permit or deny routes from being advertised in routing updates depending upon the action listed in the access list or ip prefix list." INDEX {myDistributeListCfgProtoType, myDistributeListIfIndex, myDistributeListDirection, myDistributeListFilteringProtocol } ::= { myDistributeListTable 1 } MyDistributeListEntry ::= SEQUENCE{ myDistributeListCfgProtoType MyRouteProtoType, myDistributeListIfIndex Unsigned32, myDistributeListDirection INTEGER, myDistributeListFilteringProtocol Unsigned32, myDistributeListFilterType INTEGER, myDistributeListAclName DisplayString, myDistributeListGateWayIpPrefixName DisplayString, myDistributeListPrefixIpPrefixName DisplayString, myDistributeListStatus RowStatus } myDistributeListCfgProtoType OBJECT-TYPE SYNTAX MyRouteProtoType MAX-ACCESS read-only STATUS current DESCRIPTION "This index indicate that which routing protocol configuration mode is current mode." ::={myDistributeListEntry 1} myDistributeListIfIndex OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "The interface that this distribute list apply to. If this value is 0,it indicate that this distribute list apply in all interfaces. Other value is equal to TEXTUAL-CONVENTION 'IfIndex' meaning." ::={myDistributeListEntry 2} myDistributeListDirection OBJECT-TYPE SYNTAX INTEGER{ out(1), in(2) } MAX-ACCESS read-only STATUS current DESCRIPTION "If direct is 'in' the distribute list is applied to input packets If direct is 'out' the distribute list is applied to output packets." ::={myDistributeListEntry 3} myDistributeListFilteringProtocol OBJECT-TYPE SYNTAX Unsigned32 MAX-ACCESS read-only STATUS current DESCRIPTION "If this value is 0,it indicate that this distribute list will apply on all protocol. Other value is equal to TEXTUAL-CONVENTION 'MyRouteProtoType' meaning, it indicate the protocol which this distribute list apply on." ::={myDistributeListEntry 4} myDistributeListFilterType OBJECT-TYPE SYNTAX INTEGER{ acl(1), gateway(2), prefix(3), prefix-gateway(4) } MAX-ACCESS read-write STATUS current DESCRIPTION "this field defines the filtering type which distribute-list used , 'acl' means filtering destination ip address of route information in incoming or outing packets; 'gateway' means filtering source ip address and mask of incoming packets; 'prefix' means filtering destination ip address and mask of route information in incoming or outing packets; 'prefix-gateway' means that firstly filtering destination ip address and mask of route information in incoming or outing packets, secondly filtering source ip address and mask of incoming packets. if Prefix-list filter is configed,Access-list filter can not be configed; if Access-list filter is configed,Prefix-list filter can not be configed." ::={myDistributeListEntry 5} myDistributeListAclName OBJECT-TYPE SYNTAX DisplayString(SIZE (0..32)) MAX-ACCESS read-write STATUS current DESCRIPTION " This field is valid when the field myDistributeListFilterType's value is 'acl',it's access list name that distribute-list reference to. Null string indicate that the distribute list will not reference any ACL" ::={myDistributeListEntry 6} myDistributeListGateWayIpPrefixName OBJECT-TYPE SYNTAX DisplayString(SIZE (0..32)) MAX-ACCESS read-write STATUS current DESCRIPTION " this field is valid when the field myDistributeListFilterType's value is 'gateway',it's ip prefix list name that distribute-list source ip and mask reference to. Null string indicate that the distribute list source ip and mask will not reference any ip prefix list." ::={myDistributeListEntry 7} myDistributeListPrefixIpPrefixName OBJECT-TYPE SYNTAX DisplayString(SIZE (0..32)) MAX-ACCESS read-write STATUS current DESCRIPTION " this field is valid when the field myDistributeListFilterType's value is 'gateway',it's ip prefix list name that distribute-list destination ip and mask reference to. Null string indicate that the distribute list destination ip and mask will not reference any ip prefix list." ::={myDistributeListEntry 8} myDistributeListStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "the entry status,if the value is destroy ,then delete this distribute-list." ::={myDistributeListEntry 9} myipCidrRouteExtendMIBObjects OBJECT IDENTIFIER ::= { myRouteMIB 5 } myipCidrRouteTable OBJECT-TYPE SYNTAX SEQUENCE OF MyIpCidrRouteEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "This entity's IP Routing table." REFERENCE "RFC 1213 Section 6.6, The IP Group" ::= { myipCidrRouteExtendMIBObjects 1 } myipCidrRouteEntry OBJECT-TYPE SYNTAX MyIpCidrRouteEntry MAX-ACCESS not-accessible STATUS current DESCRIPTION "A particular route to a particular destina- tion, under a particular policy." INDEX { myipCidrRouteDest, myipCidrRouteMask, myipCidrRouteTos, myipCidrRouteNextHop } ::= { myipCidrRouteTable 1 } MyIpCidrRouteEntry ::= SEQUENCE { myipCidrRouteDest IpAddress, myipCidrRouteMask IpAddress, myipCidrRouteTos Integer32, myipCidrRouteNextHop IpAddress, myipCidrRouteIfIndex Integer32, myipCidrRouteType INTEGER, myipCidrRouteProto INTEGER, myipCidrRouteAge Integer32, myipCidrRouteInfo OBJECT IDENTIFIER, myipCidrRouteNextHopAS Integer32, myipCidrRouteMetric1 Integer32, myipCidrRouteMetric2 Integer32, myipCidrRouteMetric3 Integer32, myipCidrRouteMetric4 Integer32, myipCidrRouteMetric5 Integer32, myipCidrRouteStatus RowStatus, myipCidrOspfRouteType INTEGER } myipCidrRouteDest OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "The destination IP address of this route. This object may not take a Multicast (Class D) address value. Any assignment (implicit or otherwise) of an instance of this object to a value x must be rejected if the bitwise logical-AND of x with the value of the corresponding instance of the ipCidrRouteMask object is not equal to x." ::= { myipCidrRouteEntry 1 } myipCidrRouteMask OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "Indicate the mask to be logical-ANDed with the destination address before being compared to the value in the ipCidrRouteDest field. For those systems that do not support arbitrary subnet masks, an agent constructs the value of the ipCidrRouteMask by reference to the IP Ad- dress Class. Any assignment (implicit or otherwise) of an instance of this object to a value x must be rejected if the bitwise logical-AND of x with Baker Standards Track [Page 5] RFC 2096 IP Forwarding Table MIB January 1997 the value of the corresponding instance of the ipCidrRouteDest object is not equal to ipCidrRoute- Dest." ::= { myipCidrRouteEntry 2 } -- The following convention is included for specification -- of TOS Field contents. At this time, the Host Requirements -- and the Router Requirements documents disagree on the width -- of the TOS field. This mapping describes the Router -- Requirements mapping, and leaves room to widen the TOS field -- without impact to fielded systems. myipCidrRouteTos OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The policy specifier is the IP TOS Field. The encoding of IP TOS is as specified by the following convention. Zero indicates the default path if no more specific policy applies. +-----+-----+-----+-----+-----+-----+-----+-----+ | | | | | PRECEDENCE | TYPE OF SERVICE | 0 | | | | | +-----+-----+-----+-----+-----+-----+-----+-----+ IP TOS IP TOS Field Policy Field Policy Contents Code Contents Code 0 0 0 0 ==> 0 0 0 0 1 ==> 2 0 0 1 0 ==> 4 0 0 1 1 ==> 6 0 1 0 0 ==> 8 0 1 0 1 ==> 10 0 1 1 0 ==> 12 0 1 1 1 ==> 14 1 0 0 0 ==> 16 1 0 0 1 ==> 18 1 0 1 0 ==> 20 1 0 1 1 ==> 22 1 1 0 0 ==> 24 1 1 0 1 ==> 26 1 1 1 0 ==> 28 1 1 1 1 ==> 30" ::= { myipCidrRouteEntry 3 } myipCidrRouteNextHop OBJECT-TYPE SYNTAX IpAddress MAX-ACCESS read-only STATUS current DESCRIPTION "On remote routes, the address of the next sys- tem en route; Otherwise, 0.0.0.0." ::= { myipCidrRouteEntry 4 } myipCidrRouteIfIndex OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-create STATUS current DESCRIPTION "The ifIndex value which identifies the local interface through which the next hop of this route should be reached." DEFVAL { 0 } ::= { myipCidrRouteEntry 5 } myipCidrRouteType OBJECT-TYPE SYNTAX INTEGER { other (1), -- not specified by this MIB reject (2), -- route which discards traffic local (3), -- local interface remote (4) -- remote destination } MAX-ACCESS read-create STATUS current DESCRIPTION "The type of route. Note that local(3) refers to a route for which the next hop is the final destination; remote(4) refers to a route for which the next hop is not the final destina- tion. Routes which do not result in traffic forwarding or rejection should not be displayed even if the implementation keeps them stored internally. reject (2) refers to a route which, if matched, discards the message as unreachable. This is used in some protocols as a means of correctly aggregating routes." ::= { myipCidrRouteEntry 6 } myipCidrRouteProto OBJECT-TYPE SYNTAX INTEGER { other (1), -- not specified local (2), -- local interface netmgmt (3), -- static route icmp (4), -- result of ICMP Redirect -- the following are all dynamic -- routing protocols egp (5), -- Exterior Gateway Protocol ggp (6), -- Gateway-Gateway Protocol hello (7), -- FuzzBall HelloSpeak rip (8), -- Berkeley RIP or RIP-II isIs (9), -- Dual IS-IS esIs (10), -- ISO 9542 ciscoIgrp (11), -- Cisco IGRP bbnSpfIgp (12), -- BBN SPF IGP ospf (13), -- Open Shortest Path First bgp (14), -- Border Gateway Protocol idpr (15), -- InterDomain Policy Routing ciscoEigrp (16), -- Cisco EIGRP policy (17) -- My private policy-route } MAX-ACCESS read-only STATUS current DESCRIPTION "The routing mechanism via which this route was learned. Inclusion of values for gateway rout- ing protocols is not intended to imply that hosts should support those protocols." ::= { myipCidrRouteEntry 7 } myipCidrRouteAge OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-only STATUS current DESCRIPTION "The number of seconds since this route was last updated or otherwise determined to be correct. Note that no semantics of `too old' can be implied except through knowledge of the routing protocol by which the route was learned." DEFVAL { 0 } ::= { myipCidrRouteEntry 8 } myipCidrRouteInfo OBJECT-TYPE SYNTAX OBJECT IDENTIFIER MAX-ACCESS read-create STATUS current DESCRIPTION "A reference to MIB definitions specific to the particular routing protocol which is responsi- ble for this route, as determined by the value specified in the route's ipCidrRouteProto value. If this information is not present, its value should be set to the OBJECT IDENTIFIER { 0 0 }, which is a syntactically valid object identif- ier, and any implementation conforming to ASN.1 and the Basic Encoding Rules must be able to generate and recognize this value." ::= { myipCidrRouteEntry 9 } myipCidrRouteNextHopAS OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-create STATUS current DESCRIPTION "The Autonomous System Number of the Next Hop. The semantics of this object are determined by the routing-protocol specified in the route's ipCidrRouteProto value. When this object is unknown or not relevant its value should be set to zero." DEFVAL { 0 } ::= { myipCidrRouteEntry 10 } myipCidrRouteMetric1 OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-create STATUS current DESCRIPTION "The primary routing metric for this route. The semantics of this metric are determined by the routing-protocol specified in the route's ipCidrRouteProto value. If this metric is not used, its value should be set to -1." DEFVAL { -1 } ::= { myipCidrRouteEntry 11 } myipCidrRouteMetric2 OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-create STATUS current DESCRIPTION "An alternate routing metric for this route. The semantics of this metric are determined by the routing-protocol specified in the route's ipCidrRouteProto value. If this metric is not used, its value should be set to -1." DEFVAL { -1 } ::= { myipCidrRouteEntry 12 } myipCidrRouteMetric3 OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-create STATUS current DESCRIPTION "An alternate routing metric for this route. The semantics of this metric are determined by the routing-protocol specified in the route's ipCidrRouteProto value. If this metric is not used, its value should be set to -1." DEFVAL { -1 } ::= { myipCidrRouteEntry 13 } myipCidrRouteMetric4 OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-create STATUS current DESCRIPTION "An alternate routing metric for this route. The semantics of this metric are determined by the routing-protocol specified in the route's ipCidrRouteProto value. If this metric is not used, its value should be set to -1." DEFVAL { -1 } ::= { myipCidrRouteEntry 14 } myipCidrRouteMetric5 OBJECT-TYPE SYNTAX Integer32 MAX-ACCESS read-create STATUS current DESCRIPTION "An alternate routing metric for this route. The semantics of this metric are determined by the routing-protocol specified in the route's ipCidrRouteProto value. If this metric is not used, its value should be set to -1." DEFVAL { -1 } ::= { myipCidrRouteEntry 15 } myipCidrRouteStatus OBJECT-TYPE SYNTAX RowStatus MAX-ACCESS read-create STATUS current DESCRIPTION "The row status variable, used according to row installation and removal conventions." ::= { myipCidrRouteEntry 16 } myipCidrOspfRouteType OBJECT-TYPE SYNTAX INTEGER { ospf-route (0), --ospf intra area route ospf-ia-route (1), --ospf inter area route ospf-n1-route (2), --ospf nssa external type 1 route ospf-n2-route (3), --ospf nssa external type 2 route ospf-e1-route (4), --ospf external type 1 route ospf-e2-route (5) --OSPF external type 2 route } MAX-ACCESS read-only STATUS current DESCRIPTION "this field describles the ospf route entry's type, it's valid when this route was learned by ospf protocol." ::= { myipCidrRouteEntry 17 } myRouteMIBConformance OBJECT IDENTIFIER ::= { myRouteMIB 6 } myRouteMIBCompliances OBJECT IDENTIFIER ::= { myRouteMIBConformance 1 } myRouteMIBGroups OBJECT IDENTIFIER ::= { myRouteMIBConformance 2 } -- compliance statements myRouteMIBCompliance MODULE-COMPLIANCE STATUS current DESCRIPTION "The compliance statement for entities which implement the My Route MIB" MODULE -- this module MANDATORY-GROUPS { myRouteMIBGroup, myRouteInfoMIBGroup, myRouteMapMIBGroup, myRouteRedistributeMIBGroup , myRouteFilteringMibGroup, myipCidrRouteMibGroup } ::= { myRouteMIBCompliances 1 } -- units of conformance myRouteMIBGroup OBJECT-GROUP OBJECTS { myRouteServiceStatus } STATUS current DESCRIPTION "A collection of objects providing route managment." ::= { myRouteMIBGroups 1 } myRouteInfoMIBGroup OBJECT-GROUP OBJECTS { myRoutingProtoInfoProtoType, myRoutingProtoInfoGateWay , myRoutingProtoInfoDistance , myRoutingProtoInfoLastUpdate, myDefRoutingCfgRoutingProtoType, myDefRoutingCfgAlways , myDefRoutingCfgMetric, myDefRoutingCfgMetricType, myDefRoutingCfgRouteMap, myDefRoutingCfgStatus } STATUS current DESCRIPTION "A collection of objects providing route information for all routing protocol." ::= { myRouteMIBGroups 2} myRouteMapMIBGroup OBJECT-GROUP OBJECTS { myRouteMapName, myRouteMapSequenceNumber, myRouteMapOperType , myRouteMapMatchMetric , myRouteMapMatchRouteType , myRouteMapMetricValueType , myRouteMapSetMetric , myRouteMapSetLevel , myRouteMapSetMetricType , myRouteMapSetNexthopSt, myRouteMapSetNexthopSt, myRouteMapStatus, myRouteMapMatchIpAddressAclName, myRouteMapMatchType, myRouteMapMatchIpAddressStatus, myRouteMapMatchTagValue , myRouteMapMatchTagStatus, myRouteMapMatchInterfaceIfIndex, myRouteMapMatchInterfaceStatus } STATUS current DESCRIPTION "A collection of objects providing route managment." ::= { myRouteMIBGroups 3 } myRouteRedistributeMIBGroup OBJECT-GROUP OBJECTS { -- myRouteRedistributeDefMetricVal, myRouteRedistributeProtocolCfg, myRouteRedistributeProtocol, myRouteRedistributeMetricValue, myRouteRedistributeMetricType, myRouteRedistributeTagValue, myRouteRedistributeRouteMapName, myRouteRedistributeStatus } STATUS current DESCRIPTION "A collection of objects providing route Redistributting." ::= { myRouteMIBGroups 4 } myRouteFilteringMibGroup OBJECT-GROUP OBJECTS { myIpPrefixListName, myIpPrefixListSequence, myIpPrefixListOperMethod, myIpPrefixListIpAddress, myIpPrefixListMaskLength, myIpPrefixListMinimumPrefixLength, myIpPrefixListMaximumPrefixLength, myIpPrefixListStatus, myDistributeListCfgProtoType , myDistributeListIfIndex, myDistributeListFilterType, myDistributeListDirection , myDistributeListAclName, myDistributeListGateWayIpPrefixName, myDistributeListPrefixIpPrefixName, myDistributeListFilteringProtocol, myDistributeListStatus } STATUS current DESCRIPTION "A collection of objects providing route distribute-list." ::= { myRouteMIBGroups 5 } myipCidrRouteMibGroup OBJECT-GROUP OBJECTS { myipCidrRouteDest, myipCidrRouteMask, myipCidrRouteTos, myipCidrRouteNextHop, myipCidrRouteIfIndex, myipCidrRouteType, myipCidrRouteProto, myipCidrRouteAge, myipCidrRouteInfo, myipCidrRouteNextHopAS, myipCidrRouteMetric1, myipCidrRouteMetric2, myipCidrRouteMetric3, myipCidrRouteMetric4, myipCidrRouteMetric5, myipCidrRouteStatus, myipCidrOspfRouteType } STATUS current DESCRIPTION "A collection of objects providing CIDR Route Table." ::= { myRouteMIBGroups 6 } END