-- -- Copyright 1996, 1997, 1998 Shiva Corporation -- -- Conformance statements for Shiva LanRover/E, LanRover/T, LanRover/E PLUS, -- LanRover/T PLUS, and LanRover/E XP16. -- -- These conformance statements note what IETF MIBs, defined in the -- SNMPv2-SMI syntax are implemented, are implemented. -- The agent itself is an SNMPv1 agent. SHIVA-LANROVER-CAP DEFINITIONS ::= BEGIN IMPORTS MODULE-IDENTITY FROM SNMPv2-SMI AGENT-CAPABILITIES FROM SNMPv2-CONF conformance FROM SHIVA-MIB; shivaLanRoverCapabilities MODULE-IDENTITY LAST-UPDATED "9811061830Z" ORGANIZATION "Shiva Corporation" CONTACT-INFO "Shiva Corporation 28 Crosby Drive Bedford, MA 01730" DESCRIPTION "The Shiva LanRover/E, LanRover/E PLUS, LanRover/E XP16, LanRover/T, and LanRover/T PLUS Agent Capabilities module." REVISION "9811061830Z" DESCRIPTION "The first revision of this module with MODULE-IDENTITY." REVISION "9811232145Z" DESCRIPTION "Added ShivOS 5.1. Fine-tuned the platform- specific stuff and platform names." ::= { conformance 3 } shivaLanRoverAgent45 AGENT-CAPABILITIES PRODUCT-RELEASE "LanRover/E, LanRover/E PLUS, LanRover/T, and LanRover/T PLUS 4.5" STATUS current DESCRIPTION "SNMP Agent in LanRover ShivOS 4.5 firmware. Describes only those MIBs which have SMIv2 MODULE-COMPLIANCE macro." SUPPORTS IF-MIB -- RFC 1573 INCLUDES { ifGeneralGroup, ifPacketGroup, ifRcvAddressGroup, ifStackGroup } VARIATION ifAdminStatus SYNTAX INTEGER { up(1) } ACCESS read-only DESCRIPTION "No write access via SNMP, or any other means. No administrative method to disable an interface." VARIATION ifOperStatus SYNTAX INTEGER { up(1), down(2), unknown(4), dormant(5) } DESCRIPTION "There is no testing state in this system." VARIATION ifLinkUpDownTrapEnable ACCESS read-only DESCRIPTION "No write access via SNMP, or any other means." VARIATION ifPromiscuousMode ACCESS read-only DESCRIPTION "No write access via SNMP, mode not available." VARIATION ifStackStatus ACCESS read-only DESCRIPTION "No write access via SNMP." VARIATION ifRcvAddressStatus ACCESS read-only DESCRIPTION "No write access via SNMP, or any other means." SUPPORTS DNS-RESOLVER-MIB -- RFC 1612 INCLUDES { dnsResConfigGroup, dnsResCounterGroup } VARIATION dnsResConfigMaxCnames ACCESS read-only DESCRIPTION "This object need not be writable." VARIATION dnsResConfigSbeltName ACCESS read-only DESCRIPTION "This object need not be writable." VARIATION dnsResConfigSbeltRecursion ACCESS read-only DESCRIPTION "This object need not be writable." VARIATION dnsResConfigSbeltPref ACCESS read-only DESCRIPTION "This object need not be writable." VARIATION dnsResConfigReset ACCESS read-only DESCRIPTION "This object need not be writable." -- Ethernet MIB supported only on LanRover/E and LanRover/E PLUS SUPPORTS EtherLike-MIB -- RFC 1650 INCLUDES { etherStatsGroup, etherCollisionTableGroup } -- RS-232-MIB supported for all serial ports. SUPPORTS RS-232-MIB -- RFC 1659 INCLUDES { rs232Group, rs232AsyncGroup } VARIATION rs232PortType SYNTAX INTEGER { other(1), rs232(2) } DESCRIPTION "Internal modems are described as other. Only other port type is RS-232." VARIATION rs232PortInSpeed ACCESS read-only DESCRIPTION "No write access via SNMP." VARIATION rs232PortOutSpeed ACCESS read-only DESCRIPTION "No write access via SNMP." VARIATION rs232PortInFlowType ACCESS read-only DESCRIPTION "No write access via SNMP." VARIATION rs232PortOutFlowType ACCESS read-only DESCRIPTION "No write access via SNMP." VARIATION rs232AsyncPortBits ACCESS read-only DESCRIPTION "No write access via SNMP." VARIATION rs232AsyncPortStopBits ACCESS read-only DESCRIPTION "No write access via SNMP." VARIATION rs232AsyncPortParity ACCESS read-only DESCRIPTION "No write access via SNMP." VARIATION rs232AsyncPortAutobaud SYNTAX INTEGER { disabled(2) } ACCESS read-only DESCRIPTION "No autobaud support. No write access via SNMP, but no options to set." SUPPORTS RIPv2-MIB -- RFC 1724 INCLUDES { rip2GlobalGroup, rip2IfStatGroup, rip2IfConfGroup } VARIATION rip2IfConfAuthType ACCESS read-only DESCRIPTION "No write access via SNMP." VARIATION rip2IfConfAuthKey ACCESS read-only DESCRIPTION "No write access via SNMP." VARIATION rip2IfConfSend SYNTAX INTEGER { doNotSend (1), ripVersion1 (2), rip1Compatible (3), ripVersion2 (4) } ACCESS read-only DESCRIPTION "No write access via SNMP. No Demand RIP." VARIATION rip2IfConfReceive ACCESS read-only DESCRIPTION "No write access via SNMP." VARIATION rip2IfConfDefaultMetric ACCESS read-only DESCRIPTION "No write access via SNMP." VARIATION rip2IfConfStatus SYNTAX INTEGER { active(1) } ACCESS read-only DESCRIPTION "No write access via SNMP." VARIATION rip2IfConfSrcAddress ACCESS read-only DESCRIPTION "No write access via SNMP." -- Other SNMPv1-SMI MIBs implemented: -- RFC 1213 MIB-II, but without EGP group (no EGP). See RFC 1573 -- for interfaces section. Variables atIfIndex, atPhysAddress, -- atNetAddress, and ipForwarding are read-only. All variables -- in ipRouteTable are read-only. Variables ipNetToMediaIfIndex, -- ipNetToMegiaPhysAddress, ipNetToMediaNetAddress, and -- tcpConnState are read-only. -- RFC 1229 Interface MIB Extensions. No tests. Variable -- ifExtnsRcvAddrStatus read-only. -- RFC 1231 IEEE 802.5 Token Ring MIB. Only implemented on LanRover/T -- and LanRover/T PLUS. -- Variables dot5Commands, dot5RingSpeed, dot5ActMonParticipate, -- and dot5FunctionalAddress read-only. -- RFC 1243 AppleTalk Management Information Base. The LLAP group is -- not implemented (no LocalTalk hardware). The variables -- atportType and atportIfIndex are read-only. The KIP group -- is not implemented (protocol not supported). -- RFC 1471 PPP-LCP-MIB. Instantiated for each link in -- a PPP Multlink, and again for the Multilink bundle. -- Both layers there even if Multilink not in use. -- Variables pppLinkConfigInitialMTRU, -- pppLinkConfigReceiveACCMap, pppLinkConfigTransmitACCMap, -- pppLinkConfigMagicNumber, and pppLinkConfigFcsSize are -- read-only (inconsistent with configuration model). -- RFC 1473 PPP-IPCP-MIB. Instantiated for each PPP Multilink bundle. -- Variables pppIpConfigAdminStatus and pppIpConfigCompression -- are read-only (inconsistent with configuration model). ::= { shivaLanRoverCapabilities 450 } shivaLanRoverAgent50 AGENT-CAPABILITIES PRODUCT-RELEASE "LanRover/E, LanRover/E PLUS, LanRover/T, and LanRover/T PLUS 5.0" STATUS current DESCRIPTION "SNMP Agent in LanRover ShivOS 5.0 firmware. Describes only those MIBs which have SMIv2 MODULE-COMPLIANCE macro." SUPPORTS IF-MIB -- RFC 1573 INCLUDES { ifGeneralGroup, ifPacketGroup, ifRcvAddressGroup, ifStackGroup } VARIATION ifAdminStatus SYNTAX INTEGER { up(1) } ACCESS read-only DESCRIPTION "No write access via SNMP, or any other means. No administrative method to disable an interface." VARIATION ifOperStatus SYNTAX INTEGER { up(1), down(2), unknown(4), dormant(5) } DESCRIPTION "There is no testing state in this system." VARIATION ifLinkUpDownTrapEnable ACCESS read-only DESCRIPTION "No write access via SNMP, or any other means." VARIATION ifPromiscuousMode ACCESS read-only DESCRIPTION "No write access via SNMP, mode not available." VARIATION ifStackStatus ACCESS read-only DESCRIPTION "No write access via SNMP." VARIATION ifRcvAddressStatus ACCESS read-only DESCRIPTION "No write access via SNMP, or any other means." SUPPORTS DNS-RESOLVER-MIB -- RFC 1612 INCLUDES { dnsResConfigGroup, dnsResCounterGroup } VARIATION dnsResConfigMaxCnames ACCESS read-only DESCRIPTION "This object need not be writable." VARIATION dnsResConfigSbeltName ACCESS read-only DESCRIPTION "This object need not be writable." VARIATION dnsResConfigSbeltRecursion ACCESS read-only DESCRIPTION "This object need not be writable." VARIATION dnsResConfigSbeltPref ACCESS read-only DESCRIPTION "This object need not be writable." VARIATION dnsResConfigReset ACCESS read-only DESCRIPTION "This object need not be writable." -- Ethernet MIB supported only on LanRover/E and LanRover/E PLUS SUPPORTS EtherLike-MIB -- RFC 1650 INCLUDES { etherStatsGroup, etherCollisionTableGroup } -- RS-232-MIB supported for all serial ports. SUPPORTS RS-232-MIB -- RFC 1659 INCLUDES { rs232Group, rs232AsyncGroup } VARIATION rs232PortType SYNTAX INTEGER { other(1), rs232(2) } DESCRIPTION "Internal modems are described as other. Only other port type is RS-232." VARIATION rs232PortInSpeed ACCESS read-only DESCRIPTION "No write access via SNMP." VARIATION rs232PortOutSpeed ACCESS read-only DESCRIPTION "No write access via SNMP." VARIATION rs232PortInFlowType ACCESS read-only DESCRIPTION "No write access via SNMP." VARIATION rs232PortOutFlowType ACCESS read-only DESCRIPTION "No write access via SNMP." VARIATION rs232AsyncPortBits ACCESS read-only DESCRIPTION "No write access via SNMP." VARIATION rs232AsyncPortStopBits ACCESS read-only DESCRIPTION "No write access via SNMP." VARIATION rs232AsyncPortParity ACCESS read-only DESCRIPTION "No write access via SNMP." VARIATION rs232AsyncPortAutobaud SYNTAX INTEGER { disabled(2) } ACCESS read-only DESCRIPTION "No autobaud support. No write access via SNMP, but no options to set." SUPPORTS RIPv2-MIB -- RFC 1724 INCLUDES { rip2GlobalGroup, rip2IfStatGroup, rip2IfConfGroup } VARIATION rip2IfConfAuthType ACCESS read-only DESCRIPTION "No write access via SNMP." VARIATION rip2IfConfAuthKey ACCESS read-only DESCRIPTION "No write access via SNMP." VARIATION rip2IfConfSend SYNTAX INTEGER { doNotSend (1), ripVersion1 (2), rip1Compatible (3), ripVersion2 (4) } ACCESS read-only DESCRIPTION "No write access via SNMP. No Demand RIP." VARIATION rip2IfConfReceive ACCESS read-only DESCRIPTION "No write access via SNMP." VARIATION rip2IfConfDefaultMetric ACCESS read-only DESCRIPTION "No write access via SNMP." VARIATION rip2IfConfStatus SYNTAX INTEGER { active(1) } ACCESS read-only DESCRIPTION "No write access via SNMP." VARIATION rip2IfConfSrcAddress ACCESS read-only DESCRIPTION "No write access via SNMP." -- Other SNMPv1-SMI MIBs implemented: -- RFC 1213 MIB-II, but without EGP group (no EGP). See RFC 1573 -- for interfaces section. Variables atIfIndex, atPhysAddress, -- atNetAddress, and ipForwarding are read-only. All variables -- in ipRouteTable are read-only. Variables ipNetToMediaIfIndex, -- ipNetToMegiaPhysAddress, ipNetToMediaNetAddress, and -- tcpConnState are read-only. -- RFC 1229 Interface MIB Extensions. No tests. Variable -- ifExtnsRcvAddrStatus read-only. -- RFC 1231 IEEE 802.5 Token Ring MIB. Only implemented on LanRover/T -- and LanRover/T PLUS. -- Variables dot5Commands, dot5RingSpeed, dot5ActMonParticipate, -- and dot5FunctionalAddress read-only. -- RFC 1243 AppleTalk Management Information Base. The LLAP group is -- not implemented (no LocalTalk hardware). The variables -- atportType and atportIfIndex are read-only. The KIP group -- is not implemented (protocol not supported). -- RFC 1471 PPP-LCP-MIB. Instantiated for each link in -- a PPP Multlink, and again for the Multilink bundle. -- Both layers there even if Multilink not in use. -- Variables pppLinkConfigInitialMTRU, -- pppLinkConfigReceiveACCMap, pppLinkConfigTransmitACCMap, -- pppLinkConfigMagicNumber, and pppLinkConfigFcsSize are -- read-only (inconsistent with configuration model). -- RFC 1473 PPP-IPCP-MIB. Instantiated for each PPP Multilink bundle. -- Variables pppIpConfigAdminStatus and pppIpConfigCompression -- are read-only (inconsistent with configuration model). ::= { shivaLanRoverCapabilities 500 } shivaLanRoverAgent57 AGENT-CAPABILITIES PRODUCT-RELEASE "LanRover/E, LanRover/E PLUS, LanRover/T, and LanRover/T PLUS 5.7" STATUS current DESCRIPTION "SNMP Agent in LanRover ShivOS 5.7 firmware. Describes only those MIBs which have SMIv2 MODULE-COMPLIANCE macro." SUPPORTS IF-MIB -- RFC 1573 INCLUDES { ifGeneralGroup, ifPacketGroup, ifRcvAddressGroup, ifStackGroup } VARIATION ifAdminStatus SYNTAX INTEGER { up(1) } ACCESS read-only DESCRIPTION "No write access via SNMP, or any other means. No administrative method to disable an interface." VARIATION ifOperStatus SYNTAX INTEGER { up(1), down(2), unknown(4), dormant(5) } DESCRIPTION "There is no testing state in this system." VARIATION ifLinkUpDownTrapEnable ACCESS read-only DESCRIPTION "No write access via SNMP, or any other means." VARIATION ifPromiscuousMode ACCESS read-only DESCRIPTION "No write access via SNMP, mode not available." VARIATION ifStackStatus ACCESS read-only DESCRIPTION "No write access via SNMP." VARIATION ifRcvAddressStatus ACCESS read-only DESCRIPTION "No write access via SNMP, or any other means." SUPPORTS DNS-RESOLVER-MIB -- RFC 1612 INCLUDES { dnsResConfigGroup, dnsResCounterGroup } VARIATION dnsResConfigMaxCnames ACCESS read-only DESCRIPTION "This object need not be writable." VARIATION dnsResConfigSbeltName ACCESS read-only DESCRIPTION "This object need not be writable." VARIATION dnsResConfigSbeltRecursion ACCESS read-only DESCRIPTION "This object need not be writable." VARIATION dnsResConfigSbeltPref ACCESS read-only DESCRIPTION "This object need not be writable." VARIATION dnsResConfigReset ACCESS read-only DESCRIPTION "This object need not be writable." -- Ethernet MIB supported only on LanRover/E and LanRover/E PLUS SUPPORTS EtherLike-MIB -- RFC 1650 INCLUDES { etherStatsGroup, etherCollisionTableGroup } -- RS-232-MIB supported for all serial ports. SUPPORTS RS-232-MIB -- RFC 1659 INCLUDES { rs232Group, rs232AsyncGroup } VARIATION rs232PortType SYNTAX INTEGER { other(1), rs232(2) } DESCRIPTION "Internal modems are described as other. Only other port type is RS-232." VARIATION rs232PortInSpeed ACCESS read-only DESCRIPTION "No write access via SNMP." VARIATION rs232PortOutSpeed ACCESS read-only DESCRIPTION "No write access via SNMP." VARIATION rs232PortInFlowType ACCESS read-only DESCRIPTION "No write access via SNMP." VARIATION rs232PortOutFlowType ACCESS read-only DESCRIPTION "No write access via SNMP." VARIATION rs232AsyncPortBits ACCESS read-only DESCRIPTION "No write access via SNMP." VARIATION rs232AsyncPortStopBits ACCESS read-only DESCRIPTION "No write access via SNMP." VARIATION rs232AsyncPortParity ACCESS read-only DESCRIPTION "No write access via SNMP." VARIATION rs232AsyncPortAutobaud SYNTAX INTEGER { disabled(2) } ACCESS read-only DESCRIPTION "No autobaud support. No write access via SNMP, but no options to set." SUPPORTS RIPv2-MIB -- RFC 1724 INCLUDES { rip2GlobalGroup, rip2IfStatGroup, rip2IfConfGroup } VARIATION rip2IfConfAuthType ACCESS read-only DESCRIPTION "No write access via SNMP." VARIATION rip2IfConfAuthKey ACCESS read-only DESCRIPTION "No write access via SNMP." VARIATION rip2IfConfSend SYNTAX INTEGER { doNotSend (1), ripVersion1 (2), rip1Compatible (3), ripVersion2 (4) } ACCESS read-only DESCRIPTION "No write access via SNMP. No Demand RIP." VARIATION rip2IfConfReceive ACCESS read-only DESCRIPTION "No write access via SNMP." VARIATION rip2IfConfDefaultMetric ACCESS read-only DESCRIPTION "No write access via SNMP." VARIATION rip2IfConfStatus SYNTAX INTEGER { active(1) } ACCESS read-only DESCRIPTION "No write access via SNMP." VARIATION rip2IfConfSrcAddress ACCESS read-only DESCRIPTION "No write access via SNMP." -- Other SNMPv1-SMI MIBs implemented: -- RFC 1213 MIB-II, but without EGP group (no EGP). See RFC 1573 -- for interfaces section. Variables atIfIndex, atPhysAddress, -- atNetAddress, and ipForwarding are read-only. All variables -- in ipRouteTable are read-only. Variables ipNetToMediaIfIndex, -- ipNetToMegiaPhysAddress, ipNetToMediaNetAddress, and -- tcpConnState are read-only. -- RFC 1229 Interface MIB Extensions. No tests. Variable -- ifExtnsRcvAddrStatus read-only. -- RFC 1231 IEEE 802.5 Token Ring MIB. Only implemented on LanRover/T -- and LanRover/T PLUS. -- Variables dot5Commands, dot5RingSpeed, dot5ActMonParticipate, -- and dot5FunctionalAddress read-only. -- RFC 1243 AppleTalk Management Information Base. The LLAP group is -- not implemented (no LocalTalk hardware). The variables -- atportType and atportIfIndex are read-only. The KIP group -- is not implemented (protocol not supported). -- RFC 1471 PPP-LCP-MIB. Instantiated for each link in -- a PPP Multlink, and again for the Multilink bundle. -- Both layers there even if Multilink not in use. -- Variables pppLinkConfigInitialMTRU, -- pppLinkConfigReceiveACCMap, pppLinkConfigTransmitACCMap, -- pppLinkConfigMagicNumber, and pppLinkConfigFcsSize are -- read-only (inconsistent with configuration model). -- RFC 1473 PPP-IPCP-MIB. Instantiated for each PPP Multilink bundle. -- Variables pppIpConfigAdminStatus and pppIpConfigCompression -- are read-only (inconsistent with configuration model). ::= { shivaLanRoverCapabilities 570 } shivaLanRoverAgent51 AGENT-CAPABILITIES PRODUCT-RELEASE "LanRover/E XP16 5.1" STATUS current DESCRIPTION "SNMP Agent in LanRover XP16 ShivOS 5.1 firmware. Describes only those MIBs which have SMIv2 MODULE-COMPLIANCE macro." SUPPORTS IF-MIB -- RFC 1573 INCLUDES { ifGeneralGroup, ifPacketGroup, ifRcvAddressGroup, ifStackGroup } VARIATION ifAdminStatus SYNTAX INTEGER { up(1) } ACCESS read-only DESCRIPTION "No write access via SNMP, or any other means. No administrative method to disable an interface." VARIATION ifOperStatus SYNTAX INTEGER { up(1), down(2), unknown(4), dormant(5) } DESCRIPTION "There is no testing state in this system." VARIATION ifLinkUpDownTrapEnable ACCESS read-only DESCRIPTION "No write access via SNMP, or any other means." VARIATION ifPromiscuousMode ACCESS read-only DESCRIPTION "No write access via SNMP, mode not available." VARIATION ifStackStatus ACCESS read-only DESCRIPTION "No write access via SNMP." VARIATION ifRcvAddressStatus ACCESS read-only DESCRIPTION "No write access via SNMP, or any other means." SUPPORTS DNS-RESOLVER-MIB -- RFC 1612 INCLUDES { dnsResConfigGroup, dnsResCounterGroup } VARIATION dnsResConfigMaxCnames ACCESS read-only DESCRIPTION "This object need not be writable." VARIATION dnsResConfigSbeltName ACCESS read-only DESCRIPTION "This object need not be writable." VARIATION dnsResConfigSbeltRecursion ACCESS read-only DESCRIPTION "This object need not be writable." VARIATION dnsResConfigSbeltPref ACCESS read-only DESCRIPTION "This object need not be writable." VARIATION dnsResConfigReset ACCESS read-only DESCRIPTION "This object need not be writable." -- Ethernet MIB SUPPORTS EtherLike-MIB -- RFC 1650 INCLUDES { etherStatsGroup, etherCollisionTableGroup } -- RS-232-MIB supported for all serial ports. SUPPORTS RS-232-MIB -- RFC 1659 INCLUDES { rs232Group, rs232AsyncGroup } VARIATION rs232PortType SYNTAX INTEGER { other(1), rs232(2) } DESCRIPTION "Internal modems are described as other. Only other port type is RS-232." VARIATION rs232PortInSpeed ACCESS read-only DESCRIPTION "No write access via SNMP." VARIATION rs232PortOutSpeed ACCESS read-only DESCRIPTION "No write access via SNMP." VARIATION rs232PortInFlowType ACCESS read-only DESCRIPTION "No write access via SNMP." VARIATION rs232PortOutFlowType ACCESS read-only DESCRIPTION "No write access via SNMP." VARIATION rs232AsyncPortBits ACCESS read-only DESCRIPTION "No write access via SNMP." VARIATION rs232AsyncPortStopBits ACCESS read-only DESCRIPTION "No write access via SNMP." VARIATION rs232AsyncPortParity ACCESS read-only DESCRIPTION "No write access via SNMP." VARIATION rs232AsyncPortAutobaud SYNTAX INTEGER { disabled(2) } ACCESS read-only DESCRIPTION "No autobaud support. No write access via SNMP, but no options to set." SUPPORTS RIPv2-MIB -- RFC 1724 INCLUDES { rip2GlobalGroup, rip2IfStatGroup, rip2IfConfGroup } VARIATION rip2IfConfAuthType ACCESS read-only DESCRIPTION "No write access via SNMP." VARIATION rip2IfConfAuthKey ACCESS read-only DESCRIPTION "No write access via SNMP." VARIATION rip2IfConfSend SYNTAX INTEGER { doNotSend (1), ripVersion1 (2), rip1Compatible (3), ripVersion2 (4) } ACCESS read-only DESCRIPTION "No write access via SNMP. No Demand RIP." VARIATION rip2IfConfReceive ACCESS read-only DESCRIPTION "No write access via SNMP." VARIATION rip2IfConfDefaultMetric ACCESS read-only DESCRIPTION "No write access via SNMP." VARIATION rip2IfConfStatus SYNTAX INTEGER { active(1) } ACCESS read-only DESCRIPTION "No write access via SNMP." VARIATION rip2IfConfSrcAddress ACCESS read-only DESCRIPTION "No write access via SNMP." -- Other SNMPv1-SMI MIBs implemented: -- RFC 1213 MIB-II, but without EGP group (no EGP). See RFC 1573 -- for interfaces section. Variables atIfIndex, atPhysAddress, -- atNetAddress, and ipForwarding are read-only. All variables -- in ipRouteTable are read-only. Variables ipNetToMediaIfIndex, -- ipNetToMegiaPhysAddress, ipNetToMediaNetAddress, and -- tcpConnState are read-only. -- RFC 1229 Interface MIB Extensions. No tests. Variable -- ifExtnsRcvAddrStatus read-only. -- RFC 1243 AppleTalk Management Information Base. The LLAP group is -- not implemented (no LocalTalk hardware). The variables -- atportType and atportIfIndex are read-only. The KIP group -- is not implemented (protocol not supported). -- RFC 1471 PPP-LCP-MIB. Instantiated for each link in -- a PPP Multlink, and again for the Multilink bundle. -- Both layers there even if Multilink not in use. -- Variables pppLinkConfigInitialMTRU, -- pppLinkConfigReceiveACCMap, pppLinkConfigTransmitACCMap, -- pppLinkConfigMagicNumber, and pppLinkConfigFcsSize are -- read-only (inconsistent with configuration model). -- RFC 1473 PPP-IPCP-MIB. Instantiated for each PPP Multilink bundle. -- Variables pppIpConfigAdminStatus and pppIpConfigCompression -- are read-only (inconsistent with configuration model). ::= { shivaLanRoverCapabilities 510 } END