Wellfleet-SYNC-MIB DEFINITIONS ::= BEGIN -- Created by mdl2asn version 3.1 -- Creation date: Wed Aug 30 16:48:41 EDT 1995 IMPORTS Counter, Gauge, TimeTicks FROM RFC1155-SMI OBJECT-TYPE FROM RFC-1212 DisplayString FROM RFC1213-MIB wfLine FROM Wellfleet-COMMON-MIB; wfSyncTable OBJECT-TYPE SYNTAX SEQUENCE OF WfSyncEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "SYNC line record" ::= { wfLine 5 } wfSyncEntry OBJECT-TYPE SYNTAX WfSyncEntry ACCESS not-accessible STATUS mandatory DESCRIPTION "An entry in the SYNC table" INDEX { wfSyncSlot, wfSyncConnector } ::= { wfSyncTable 1 } WfSyncEntry ::= SEQUENCE { wfSyncDelete INTEGER, wfSyncDisable INTEGER, wfSyncState INTEGER, wfSyncSlot INTEGER, wfSyncConnector INTEGER, wfSyncCct INTEGER, wfSyncBofl INTEGER, wfSyncBoflTmo INTEGER, wfSyncMtu INTEGER, wfSyncMadr OCTET STRING, wfSyncPromiscuous INTEGER, wfSyncXid INTEGER, wfSyncClkSource INTEGER, wfSyncClkSpeed INTEGER, wfSyncSignalMode INTEGER, wfSyncRtsEnable INTEGER, wfSyncBurstCount INTEGER, wfSyncService INTEGER, wfSyncRetryCount INTEGER, wfSyncLinkIdleTimer INTEGER, wfSyncRetryTimer INTEGER, wfSyncExtendedAddress INTEGER, wfSyncExtendedAddressForce INTEGER, wfSyncExtendedControl INTEGER, wfSyncExtendedControlForce INTEGER, wfSyncConnectAttempts INTEGER, wfSyncWindowSizeTx INTEGER, wfSyncWindowSizeTxExtc INTEGER, wfSyncMinFrameSpace INTEGER, wfSyncLocalAddress INTEGER, wfSyncRemoteAddress INTEGER, wfSyncPassThruLocalMadr OCTET STRING, wfSyncPassThruRemoteMadr OCTET STRING, wfSyncWanProtocol INTEGER, wfSyncCrcSize INTEGER, wfSyncRxOctets Counter, wfSyncRxFrames Counter, wfSyncTxOctets Counter, wfSyncTxFrames Counter, wfSyncRxErrors Counter, wfSyncTxErrors Counter, wfSyncLackRescRx Counter, wfSyncLackRescTx Counter, wfSyncUnderFlowTx Counter, wfSyncRejectsTx Counter, wfSyncRejectsRx Counter, wfSyncOverFlowRx Counter, wfSyncFramesIncompRx Counter, wfSyncBadFramesRx Counter, wfSyncFrameRejectsRx Counter, wfSyncRuntsRx Counter, wfSyncT1Timeouts Counter, wfSyncMemoryErrors Counter, wfSyncMediaType INTEGER, wfSyncCfgTxQueueLength INTEGER, wfSyncCfgRxQueueLength INTEGER, wfSyncTxQueueLength INTEGER, wfSyncRxQueueLength INTEGER, wfSyncRxReplenMisses Counter, wfSyncStartUpMode INTEGER, wfSyncIdleRRFrames INTEGER, wfSyncMultilineMode INTEGER, wfSyncBODExamPeriod INTEGER, wfSyncBODFullThreshold INTEGER, wfSyncBODRecoverThreshold INTEGER, wfSyncBODPeriodsToFail INTEGER, wfSyncKG84ACycle INTEGER, wfSyncKG84ASyncLossInterval INTEGER, wfSyncKG84ARemoteResyncWait INTEGER, wfSyncKG84ASyncPulse INTEGER, wfSyncKG84AResyncs INTEGER, wfSyncKG84AResyncsDetected INTEGER, wfSyncKG84ABsu INTEGER, wfSyncKG84AState INTEGER, wfSyncKG84AOkFrames INTEGER, wfSyncPollingEnable INTEGER, wfSyncBackupPool INTEGER, wfSyncDemandPool INTEGER, wfSyncLineNumber INTEGER, wfSyncHoldDownTime INTEGER, wfSyncNetworkType INTEGER, wfSyncActiveCct INTEGER, wfSyncCableType INTEGER, wfSyncRxDropPackets Counter, wfSyncTxDropPackets Counter, wfSyncModule INTEGER, wfSyncActualConnector INTEGER, wfSyncLineCoding INTEGER, wfSyncLastChange TimeTicks, wfSyncOutQLen Gauge, wfSyncRemoteLpbkDetection INTEGER, wfSyncLastState INTEGER, wfSyncExternalClkSpeed INTEGER, wfSyncBChannelOverride INTEGER, wfSyncBChannel INTEGER, wfSyncForceIFTF INTEGER, wfSyncPriority INTEGER, wfSyncTurboBofl INTEGER, wfSyncBoflNum INTEGER, wfSyncBoflLen INTEGER, wfSyncTurboBoflMisses INTEGER, wfSyncTurboBoflInvocations INTEGER, wfSyncBandwidthOnDemandPool INTEGER, wfSyncBODRecoverPeriodsToPass INTEGER, wfSyncBODHistory DisplayString, wfSyncBODDebugFlag INTEGER, wfSyncBChRateAdaption INTEGER, wfSyncBChActualRateAdaption INTEGER, wfSyncWanType INTEGER, wfSyncAsyncBaudRate INTEGER, wfSyncCfgAsyncCmndMaxIdles INTEGER, wfSyncAsyncCmndMaxIdles INTEGER, wfSyncCfgAsyncDataMaxIdles INTEGER, wfSyncAsyncDataMaxIdles INTEGER, wfSyncFramesAbortTx Counter, wfSyncPasyncParityType INTEGER, wfSyncPasyncCharacterLength INTEGER, wfSyncPasyncStopLength INTEGER, wfSyncPasyncBaudRate INTEGER, wfSyncLocalConnectionState INTEGER, wfSyncRemoteConnectionState INTEGER, wfSyncTimeSlotAssignment DisplayString, wfSyncEiaStatus INTEGER, wfSyncEiaStatusReset INTEGER, wfSyncUcastMap INTEGER } wfSyncDelete OBJECT-TYPE SYNTAX INTEGER { created(1), deleted(2) } ACCESS read-write STATUS mandatory DESCRIPTION "Create/Delete parameter" DEFVAL { created } ::= { wfSyncEntry 1 } wfSyncDisable OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } ACCESS read-write STATUS mandatory DESCRIPTION "Enable/Disable parameter" DEFVAL { enabled } ::= { wfSyncEntry 2 } wfSyncState OBJECT-TYPE SYNTAX INTEGER { up(1), down(2), init(3), wait(4), notpresent(5), dsrwait(6), holddown(7), remoteloop(8), lineloopbofltest(19), notpres(20) } ACCESS read-only STATUS mandatory DESCRIPTION "Line Driver state variable, Reflects the current state of the Line Driver. NOTPRESENT is an obsoleted state. It is replaced with NOTPRES." DEFVAL { notpres } ::= { wfSyncEntry 3 } wfSyncSlot OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Instance ID Slot, filled in by driver" ::= { wfSyncEntry 4 } wfSyncConnector OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Instance ID Connector, filled in by driver. For the ASN this attribute is an encoded value and is equal to 'module'*10 + 'connector'. Where 'module' is defined in attribute 86 and 'connector' is defined in attribute 78 of this table. For non-ASN platforms this attribute is the physical connector number on the slot." ::= { wfSyncEntry 5 } wfSyncCct OBJECT-TYPE SYNTAX INTEGER(1..1023) ACCESS read-write STATUS mandatory DESCRIPTION "CCT number for this line instance" ::= { wfSyncEntry 6 } wfSyncBofl OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } ACCESS read-write STATUS mandatory DESCRIPTION "breath of life parameter" DEFVAL { enabled } ::= { wfSyncEntry 7 } wfSyncBoflTmo OBJECT-TYPE SYNTAX INTEGER(1..60) ACCESS read-write STATUS mandatory DESCRIPTION "breath of life timeout in seconds" DEFVAL { 5 } ::= { wfSyncEntry 8 } wfSyncMtu OBJECT-TYPE SYNTAX INTEGER(3..4608) ACCESS read-write STATUS mandatory DESCRIPTION "MTU parameter, this is buffer size for SYNC media, fixed" DEFVAL { 1600 } ::= { wfSyncEntry 9 } wfSyncMadr OBJECT-TYPE SYNTAX OCTET STRING ACCESS read-only STATUS mandatory DESCRIPTION "Line MAC address, fixed - line driver fills in from the 48 bit address stored in the serial number prom for this connector." ::= { wfSyncEntry 10 } wfSyncPromiscuous OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } ACCESS read-write STATUS mandatory DESCRIPTION "The promiscuous parameter allows address filtering based on the local and remote addresses. When enabled, all frames are received, disabled indicates only frames destined for this local address are received" DEFVAL { disabled } ::= { wfSyncEntry 11 } wfSyncXid OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } ACCESS read-write STATUS mandatory DESCRIPTION "XID enable/disable parameter. This parameter is used to enable or disable transmission/reception of Test XID frames." DEFVAL { disabled } ::= { wfSyncEntry 12 } wfSyncClkSource OBJECT-TYPE SYNTAX INTEGER { internal(1), external(2) } ACCESS read-write STATUS mandatory DESCRIPTION "Tx/Rx clock source is either internally or external generated." DEFVAL { external } ::= { wfSyncEntry 13 } wfSyncClkSpeed OBJECT-TYPE SYNTAX INTEGER { clk1200b(1200), clk2400b(2401), clk4800b(4807), clk7200b(7204), clk9600b(9615), clk19200b(19230), clk32000b(32051), clk38400b(38461), clk56k(56818), clk64k(64102), clk125k(125000), clk230k(227272), clk420k(416666), clk625k(625000), clk833k(833333), clk1mb(1250000), clk2mb(2500000), clk5mb(5000000) } ACCESS read-write STATUS mandatory DESCRIPTION "Internal Tx/Rx clock speed. This speed selection is valid only when internal clocking is selected." DEFVAL { clk64k } ::= { wfSyncEntry 14 } wfSyncSignalMode OBJECT-TYPE SYNTAX INTEGER { balanced(1), unbalanced(2) } ACCESS read-write STATUS mandatory DESCRIPTION "The signal mode parameter indicates the line paramter balanced or unbalanced." DEFVAL { balanced } ::= { wfSyncEntry 15 } wfSyncRtsEnable OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2), kg84aenabled(3) } ACCESS read-write STATUS mandatory DESCRIPTION "Note: In KG84 support, RTS has a different meaning" DEFVAL { disabled } ::= { wfSyncEntry 16 } wfSyncBurstCount OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2), unlimited(3) } ACCESS read-write STATUS mandatory DESCRIPTION "Allows control over the DMA burst cycle duration on MK5025 based products. This attribute is ignored for AN and ASN products. The default is always 8 short word bursts (ENABLED). There are only two cases in which this attribute should be changed. Case 1: In certain cases with DSDE and DSE link modules when one or both of the ethernet ports are suffering from excessive TxUflo or RxOflo errors, the BurstCount of one or both SYNC interfaces can be set to single short word bursts (DISABLED). The only modules for which this may be necessary are the DSDE (5430 - Dual Sync, Dual Enet) (module ID 112) and the DSE (5420 - Dual Sync, Single Enet) (module ID 116). If after making the change, the TxUflo or RxOflo errors persist on the ethernet or this SYNC interface starts to get UnderFlowTx or OverFlowRx errors, then the Link Module is overloaded and a more significant software configuration change or a hardware configuration change is needed. Case 2: When a SYNC interface on an mk5025 based Link Module is getting UnderFlowTx or OverFlowRx errors while running at bandwidths greater than 2Mbps, the errors may be eliminated by setting this attribute to unlimited burst mode (UNLIMITED). If after making the change, the errors persist or the same errors start on another SYNC interface or one of the ethernet interfaces on the same module starts to get TxUflo or RxOflo errors, then the Link Module is overloaded and a more significant software configuration change or a hardware configuration change is needed. For 6Mbps full duplex operation, this attribute will most likely need to be set to UNLIMITED and all other interfaces on this module will most likely have to be deconfigured." DEFVAL { enabled } ::= { wfSyncEntry 17 } wfSyncService OBJECT-TYPE SYNTAX INTEGER { transparent(1), llc1(2), llc2(3) } ACCESS read-write STATUS mandatory DESCRIPTION "Service type for this circuit. Transparent is raw HDLC mode, LLC1 will prefix the HDLC address and control fields to the frame. The LLC2 service provides the LAPB protocol service." DEFVAL { llc1 } ::= { wfSyncEntry 18 } wfSyncRetryCount OBJECT-TYPE SYNTAX INTEGER(1..64) ACCESS read-write STATUS mandatory DESCRIPTION "The Retry count parameter indicates the number of retransmission attempts which will be tried per frame before a line is determined to be down. The retry count is max attempts following expiration of the T1 timer. This parameter is equal to the N2 counter in ICB." DEFVAL { 16 } ::= { wfSyncEntry 19 } wfSyncLinkIdleTimer OBJECT-TYPE SYNTAX INTEGER(1..9999) ACCESS read-write STATUS mandatory DESCRIPTION "The link idle parameter is the number of seconds before a line has been determined to be idle. An idle line is considered disconnectd This value is expressed in seconds." DEFVAL { 9 } ::= { wfSyncEntry 20 } wfSyncRetryTimer OBJECT-TYPE SYNTAX INTEGER(1..9999) ACCESS read-write STATUS mandatory DESCRIPTION "The Retry Timer parameter indicates the timeout in tenths of seconds for a response to be heard form the link. Link control frames are sent at the expiration of this timer value. The frames will be resent up to retry count (N2) at which time the link will be disconnected." DEFVAL { 30 } ::= { wfSyncEntry 21 } wfSyncExtendedAddress OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } ACCESS read-write STATUS mandatory DESCRIPTION "This parameter controls length determination of the address field. When this parameter is enabled, the first bit of the address field be tested to determine the length of address field in octets." DEFVAL { disabled } ::= { wfSyncEntry 22 } wfSyncExtendedAddressForce OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } ACCESS read-write STATUS mandatory DESCRIPTION "When this parameter is enabled, the receiver will assume that all address fields are 2 octets in length regardless of the first two bits of the control field. Usefull only in Transparent Mode." DEFVAL { disabled } ::= { wfSyncEntry 23 } wfSyncExtendedControl OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } ACCESS read-write STATUS mandatory DESCRIPTION "This parameter allows the control fields of all S and I frames to become 2 octets in length instead of one. Numbering of all I frame become modulo 128 instead of modulo 8. The control field of U frames remains one octet in length." DEFVAL { disabled } ::= { wfSyncEntry 24 } wfSyncExtendedControlForce OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } ACCESS read-write STATUS mandatory DESCRIPTION "This parameter when enabled will force all control fields to become two octets in length regardless the first two bits in the control field. Usefull only in Transparent Mode. (LLC1)" DEFVAL { disabled } ::= { wfSyncEntry 25 } wfSyncConnectAttempts OBJECT-TYPE SYNTAX INTEGER(1..9999) ACCESS read-write STATUS mandatory DESCRIPTION "This parameter controls the number of connection attempts which will be made during a LAPB connection request. This parameter is applicable only during LLC2 service." DEFVAL { 10 } ::= { wfSyncEntry 26 } wfSyncWindowSizeTx OBJECT-TYPE SYNTAX INTEGER(1..7) ACCESS read-write STATUS mandatory DESCRIPTION "The window size parameter controls the number of I frames which may be transmitted without acknowledgement. Non EXTC mode." DEFVAL { 1 } ::= { wfSyncEntry 27 } wfSyncWindowSizeTxExtc OBJECT-TYPE SYNTAX INTEGER(1..7) ACCESS read-write STATUS mandatory DESCRIPTION "The window size parameter controls the number of I frames which may be transmitted without acknowledgement in EXTC mode." DEFVAL { 1 } ::= { wfSyncEntry 28 } wfSyncMinFrameSpace OBJECT-TYPE SYNTAX INTEGER(1..32) ACCESS read-write STATUS mandatory DESCRIPTION "The minimum frame spacing parameter defines the number of flags that are transmitted between adjacent frames." DEFVAL { 1 } ::= { wfSyncEntry 29 } wfSyncLocalAddress OBJECT-TYPE SYNTAX INTEGER { addressdte(3), addressdce(1), addressexplicit(7) } ACCESS read-write STATUS mandatory DESCRIPTION "The local address parameter contains the DTE,DCE or EXPLICIT value expressed as a single octet. It may be extended to 2 octets if EXTA has been set." DEFVAL { addressexplicit } ::= { wfSyncEntry 30 } wfSyncRemoteAddress OBJECT-TYPE SYNTAX INTEGER { addressdte(3), addressdce(1), addressexplicit(7) } ACCESS read-write STATUS mandatory DESCRIPTION "The remote address parameter contains the DTE,DCE or EXPLICIT value expressed as a single octet. It may be extended to 2 octets if EXTA has been set." DEFVAL { addressexplicit } ::= { wfSyncEntry 31 } wfSyncPassThruLocalMadr OBJECT-TYPE SYNTAX OCTET STRING ACCESS read-write STATUS mandatory DESCRIPTION "48 bit MAC address of Local end of Sync Passthru circuit" ::= { wfSyncEntry 32 } wfSyncPassThruRemoteMadr OBJECT-TYPE SYNTAX OCTET STRING ACCESS read-write STATUS mandatory DESCRIPTION "48 bit MAC address of Remote end of Sync Passthru circuit" ::= { wfSyncEntry 33 } wfSyncWanProtocol OBJECT-TYPE SYNTAX INTEGER { standard(1), passthru(2), ppp(3), smds(4), framerelay(5), x25(6), switch(7), sw(8), atm(9), lapb(10), sdlc(11), aot(12) } ACCESS read-write STATUS mandatory DESCRIPTION "WAN protocol selection is provided via this parameter. The supported protocols can be selected per interface." DEFVAL { standard } ::= { wfSyncEntry 34 } wfSyncCrcSize OBJECT-TYPE SYNTAX INTEGER { crc16bit(1), crc32bit(2) } ACCESS read-write STATUS mandatory DESCRIPTION "CRC size parameter, 16 bit standard CCITT or extended 32 bit CRC" DEFVAL { crc16bit } ::= { wfSyncEntry 35 } wfSyncRxOctets OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Number of octets received without error" ::= { wfSyncEntry 36 } wfSyncRxFrames OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Number of frames received without error" ::= { wfSyncEntry 37 } wfSyncTxOctets OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Number of octets transmitted without error" ::= { wfSyncEntry 38 } wfSyncTxFrames OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Number of frames transmitted without error" ::= { wfSyncEntry 39 } wfSyncRxErrors OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Number of receive errors" ::= { wfSyncEntry 40 } wfSyncTxErrors OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Number of transmission errors" ::= { wfSyncEntry 41 } wfSyncLackRescRx OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Number of Rx frames dropped due to lack of buffer resources" ::= { wfSyncEntry 42 } wfSyncLackRescTx OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Number of frames clipped in driver's transmit routine due to transmit congestion." ::= { wfSyncEntry 43 } wfSyncUnderFlowTx OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Number of transmission underflows, device FIFO went empty before next DMA request was granted." ::= { wfSyncEntry 44 } wfSyncRejectsTx OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "For the mk50 driver: Number of reject frames which were transmitted For the quicsync driver: Not used For the quicsync driver in Async mode: Number of frames that grew, due to escaping, larger than a buffer" ::= { wfSyncEntry 45 } wfSyncRejectsRx OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "For the mk50 driver: Number of reject frames which were received For the quicsync driver: Number of HDLC frames received with a non-matching address For the quicsync driver in Async mode: Number of frames received that did not fit within a buffer" ::= { wfSyncEntry 46 } wfSyncOverFlowRx OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Number of receive overflows, device FIFO overflowed before next DMA cycle granted. No buffer resources available." ::= { wfSyncEntry 47 } wfSyncFramesIncompRx OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Number of frames which were incompletely received. These are frames which may have resulted from FRMRR errors." ::= { wfSyncEntry 48 } wfSyncBadFramesRx OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Number of bad receive frames, caused by FCS errors or non octet aligned." ::= { wfSyncEntry 49 } wfSyncFrameRejectsRx OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Number of Frame Rejects received" ::= { wfSyncEntry 50 } wfSyncRuntsRx OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Number of runt frames received or number of frames where the Carrier Detect signal was lost during reception." ::= { wfSyncEntry 51 } wfSyncT1Timeouts OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Number of T1 timeout's detected. The T1 timer is the link retransmission timer. Link control frames will be retransmitted when T1 expires. This is a count of the number of timeouts." ::= { wfSyncEntry 52 } wfSyncMemoryErrors OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Number of memory access errors detected. A MERR is the expiration of a DMA cycle without the bus being granted within 26us." ::= { wfSyncEntry 53 } wfSyncMediaType OBJECT-TYPE SYNTAX INTEGER { default(1), t1(2), e1(3), raisedtr(4), v25bis(5), bri(6), isdnleased(7), hayes(8) } ACCESS read-write STATUS mandatory DESCRIPTION "Media type selection is provided via this parameter" DEFVAL { default } ::= { wfSyncEntry 54 } wfSyncCfgTxQueueLength OBJECT-TYPE SYNTAX INTEGER(0..255) ACCESS read-write STATUS mandatory DESCRIPTION "Configured Transmit Queue Length. Values other than zero over-ride the router selected values. A value of zero has a special meaning. Zero causes router based default values to be used. Values larger than the compiled ring size are truncated to the compiled ring size. " ::= { wfSyncEntry 55 } wfSyncCfgRxQueueLength OBJECT-TYPE SYNTAX INTEGER(0..255) ACCESS read-write STATUS mandatory DESCRIPTION "Configured Receive Queue Length. Values other than zero over-ride the router selected values. A value of zero has a special meaning. Zero causes router based default values to be used. Values larger than the compiled ring size are truncated to the compiled ring size. " ::= { wfSyncEntry 56 } wfSyncTxQueueLength OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Current Transmit Queue Length." ::= { wfSyncEntry 57 } wfSyncRxQueueLength OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Current Receive Queue Length." ::= { wfSyncEntry 58 } wfSyncRxReplenMisses OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Number of packet buffer misses while attempting to replenish driver receive ring." ::= { wfSyncEntry 59 } wfSyncStartUpMode OBJECT-TYPE SYNTAX INTEGER { active(1), passive(2) } ACCESS read-write STATUS mandatory DESCRIPTION "Initiation of link level for LLC2 running LAPB" DEFVAL { active } ::= { wfSyncEntry 60 } wfSyncIdleRRFrames OBJECT-TYPE SYNTAX INTEGER { on(1), off(2) } ACCESS read-write STATUS mandatory DESCRIPTION "Transmit Link level RR's (Reciever Readys) during idle time. Every wfSyncLinkIdleTimer expiration an RR will be sent." DEFVAL { off } ::= { wfSyncEntry 61 } wfSyncMultilineMode OBJECT-TYPE SYNTAX INTEGER { standard(1), monitor(2), primary(3), secondary(4) } ACCESS read-write STATUS mandatory DESCRIPTION "This indicates the roll the sync line plays in a Bandwidth on Demand multiline circuit. If this is not BOD, the mode is standard." DEFVAL { standard } ::= { wfSyncEntry 62 } wfSyncBODExamPeriod OBJECT-TYPE SYNTAX INTEGER(5..200) ACCESS read-write STATUS mandatory DESCRIPTION "This indicates the interval that the line should be polled for possible congestion. This value is in tenths of a second" DEFVAL { 10 } ::= { wfSyncEntry 63 } wfSyncBODFullThreshold OBJECT-TYPE SYNTAX INTEGER(10..100) ACCESS read-write STATUS mandatory DESCRIPTION "This is the percentage of the theoretical maximum line throughput that must be reached or exceeded before the line is considered congested." DEFVAL { 70 } ::= { wfSyncEntry 64 } wfSyncBODRecoverThreshold OBJECT-TYPE SYNTAX INTEGER(10..100) ACCESS read-write STATUS mandatory DESCRIPTION "This is the recovery threshold expressed as a percentage of the theoretical maximum line throughput. The actual throughput must fall below this percentage in order for the BOD circuit to revert back to the primary line only. This value should be set to less than one half the value of wfSyncBODFullThreshold to avoid toggling the secondary." DEFVAL { 20 } ::= { wfSyncEntry 65 } wfSyncBODPeriodsToFail OBJECT-TYPE SYNTAX INTEGER(1..100) ACCESS read-write STATUS mandatory DESCRIPTION "This is the number of consecutive periods where the line throughput is above the congestion threshold required to declare the line congested." DEFVAL { 10 } ::= { wfSyncEntry 66 } wfSyncKG84ACycle OBJECT-TYPE SYNTAX INTEGER { cycle5ms(5), cycle10ms(10), cycle25ms(25), cycle50ms(50), cycle100ms(100), cycle200ms(200), cycle500ms(500) } ACCESS read-write STATUS mandatory DESCRIPTION "Monitor sample time in milliseconds" DEFVAL { cycle100ms } ::= { wfSyncEntry 67 } wfSyncKG84ASyncLossInterval OBJECT-TYPE SYNTAX INTEGER { num2cycles(2), num5cycles(5), num10cycles(10), num25cycles(25), num50cycles(50), num100cycles(100), num200cycles(200), num500cycles(500) } ACCESS read-write STATUS mandatory DESCRIPTION "timer starts when FCS error detected; if no good frame received during this time, declare loss of synchronization" DEFVAL { num50cycles } ::= { wfSyncEntry 68 } wfSyncKG84ARemoteResyncWait OBJECT-TYPE SYNTAX INTEGER { num2cycles(2), num5cycles(5), num10cycles(10), num25cycles(25), num50cycles(50), num100cycles(100), num200cycles(200), num500cycles(500) } ACCESS read-write STATUS mandatory DESCRIPTION "when loss of synchronization is detected, and CTS is low, start timer; if CTS is not high when timer expires, force sync request" DEFVAL { num200cycles } ::= { wfSyncEntry 69 } wfSyncKG84ASyncPulse OBJECT-TYPE SYNTAX INTEGER(2..4096) ACCESS read-write STATUS mandatory DESCRIPTION "interval to pulse KG84a SYNC signal, in milliseconds" DEFVAL { 10 } ::= { wfSyncEntry 70 } wfSyncKG84AResyncs OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "number of KG84 resyncs performed" ::= { wfSyncEntry 71 } wfSyncKG84AResyncsDetected OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "number of KG84 resyncs detected" ::= { wfSyncEntry 72 } wfSyncKG84ABsu OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "value taken from mk5025 sync chip control block" ::= { wfSyncEntry 73 } wfSyncKG84AState OBJECT-TYPE SYNTAX INTEGER { idle(1), local(2), remote(3), sync(4) } ACCESS read-only STATUS mandatory DESCRIPTION "state of sync" DEFVAL { idle } ::= { wfSyncEntry 74 } wfSyncKG84AOkFrames OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "count of valid frames received. This value taken from normal sync processing, updated by timer routine when FCE error detected" ::= { wfSyncEntry 75 } wfSyncPollingEnable OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } ACCESS read-write STATUS mandatory DESCRIPTION "Enable or Disable Sync Polling. When Sync Polling is enabled, the the Sync Driver will be disabled if the DSR lead is dropped. If disabled, the DSR lead is ignored." DEFVAL { disabled } ::= { wfSyncEntry 76 } wfSyncBackupPool OBJECT-TYPE SYNTAX INTEGER(1..255) ACCESS read-write STATUS mandatory DESCRIPTION "Backup pool id containing this line driver" ::= { wfSyncEntry 77 } wfSyncDemandPool OBJECT-TYPE SYNTAX INTEGER(1..255) ACCESS read-write STATUS mandatory DESCRIPTION "Dial on demand pool id containing this line driver" ::= { wfSyncEntry 78 } wfSyncLineNumber OBJECT-TYPE SYNTAX INTEGER ACCESS read-write STATUS mandatory DESCRIPTION "line number for this line instance" ::= { wfSyncEntry 79 } wfSyncHoldDownTime OBJECT-TYPE SYNTAX INTEGER ACCESS read-write STATUS mandatory DESCRIPTION "Wait this number of seconds before bringing the line up. This prevents line waffling if this is a reactivated primary line in a backup configuration and it is a dirty line" ::= { wfSyncEntry 80 } wfSyncNetworkType OBJECT-TYPE SYNTAX INTEGER { gosip(1), net2(2), c03(3) } ACCESS read-write STATUS mandatory DESCRIPTION "Specific Network Link Level to be executed, LAPB mode only. The types GOSIP and NET2 are used in conjunction with an MK5025 chip revision C04. If a customer must be NET2 compliant and is using an MK5025 chip revision C03, the C03 option must be used." DEFVAL { net2 } ::= { wfSyncEntry 81 } wfSyncActiveCct OBJECT-TYPE SYNTAX INTEGER(1..1023) ACCESS read-only STATUS mandatory DESCRIPTION "Active CCT number for this line instance" ::= { wfSyncEntry 82 } wfSyncCableType OBJECT-TYPE SYNTAX INTEGER(0..4) ACCESS read-write STATUS mandatory DESCRIPTION "Type of Cable attached to the sync port - this is needed for V.25bis and Raise DTR to properly communicate with the modem" ::= { wfSyncEntry 83 } wfSyncRxDropPackets OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Number of Rx packets dropped by driver." ::= { wfSyncEntry 84 } wfSyncTxDropPackets OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Number of Tx packets dropped by driver." ::= { wfSyncEntry 85 } wfSyncModule OBJECT-TYPE SYNTAX INTEGER { one(1), two(2), three(3), four(4) } ACCESS read-only STATUS mandatory DESCRIPTION "Module number for ASN platform, filled in by driver. For non-ASN platforms this attribute will not be used." ::= { wfSyncEntry 86 } wfSyncActualConnector OBJECT-TYPE SYNTAX INTEGER { one(1), two(2), three(3), four(4), five(5), six(6), seven(7), eight(8) } ACCESS read-only STATUS mandatory DESCRIPTION "Actual connector number for ASN platform, filled in by driver. For non-ASN platforms, this attribute will not be used." ::= { wfSyncEntry 87 } wfSyncLineCoding OBJECT-TYPE SYNTAX INTEGER { nrz(1), nrzi(2), nrzimark(3) } ACCESS read-write STATUS mandatory DESCRIPTION "Line Coding for sync interface. Can be either NRZ or NRZI." DEFVAL { nrz } ::= { wfSyncEntry 88 } wfSyncLastChange OBJECT-TYPE SYNTAX TimeTicks ACCESS read-only STATUS mandatory DESCRIPTION "The value of SysUpTime at the time the interface entered it's current operational state (UP state). SysUpTime is defined as the time (in hundredths of a second) since the network management portion of the system was last re-initialized. Usually the time since boot." ::= { wfSyncEntry 89 } wfSyncOutQLen OBJECT-TYPE SYNTAX Gauge ACCESS read-only STATUS mandatory DESCRIPTION "The instantaneous current length of the output packet queue (in packets)." ::= { wfSyncEntry 90 } wfSyncRemoteLpbkDetection OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } ACCESS read-write STATUS mandatory DESCRIPTION "This attribute enables Remote Loopback Detection. When enabled along with wfSyncBofl, the device driver will detect when it is receiving its own BOFL packets and will bring the interface down assuming that somewhere down stream the link has been put into loopback. " DEFVAL { disabled } ::= { wfSyncEntry 91 } wfSyncLastState OBJECT-TYPE SYNTAX INTEGER { up(1), down(2), init(3), wait(4), notpresent(5), dsrwait(6), holddown(7), remoteloop(8), notpres(20) } ACCESS read-only STATUS mandatory DESCRIPTION "The state which the driver was in prior to the most recent re-initialization." ::= { wfSyncEntry 92 } wfSyncExternalClkSpeed OBJECT-TYPE SYNTAX INTEGER(1200..6000000) ACCESS read-write STATUS mandatory DESCRIPTION "External Clock Speed. If external clocking is configured, this attribute should be set to the clock speed of the externally supplied clock. Depending on the protocols configured on this interface, this value may control internal decision making within the router. In some cases, router software uses this attribute for route selection. If Priority Queuing is configured, it chooses queue depths based on this attribute. This attribute has no effect when Internal clocking is configured." DEFVAL { 64102 } ::= { wfSyncEntry 93 } wfSyncBChannelOverride OBJECT-TYPE SYNTAX INTEGER { bchannel1(1), bchannel2(2), default(3), floatingb(4) } ACCESS read-write STATUS mandatory DESCRIPTION "For ISDN, indicates which B Channel we're using. By default, we'd like the B Channel tied to the connector defined in the instance id, but the user may override that here, which gives the ability of connecting the B Channel to specific SCC's." DEFVAL { default } ::= { wfSyncEntry 94 } wfSyncBChannel OBJECT-TYPE SYNTAX INTEGER { bchannel1(1), bchannel2(2) } ACCESS read-only STATUS mandatory DESCRIPTION "Indicates which B Channel is running" ::= { wfSyncEntry 95 } wfSyncForceIFTF OBJECT-TYPE SYNTAX INTEGER { default(1), forcehdlcflags(2), forceidles(3), flagstreaming(4) } ACCESS read-write STATUS mandatory DESCRIPTION "Specifies the Inter Frame Time Fill (IFTF) pattern which gets transmitted when no data is being transmitted on a particular channel. For SDLC Lines, DEFAULT and FORCE_HDLC_FLAGS both result in HDLC Flags (0x7E) as the fill character. FLAGSTREAMING will cause the fill character to alternate between Flags (0x7E) and Idles (0xFF), depending upon the current state of the line. For ISDN BRI Lines, DEFAULT, FORCE IDLES and FLAGSTREAMING all result in Idles (0xFF) as the fill character. For all other line types, DEFAULT, FORCE HDLC FLAGS and FLAGSTREAMING all result in HDLC Flags (0x7E) as the fill character. Leave this field at the default unless required for the attached device. The AS/400 high speed serial controller requires the use of FLAGSTREAMING for error-free operation." DEFVAL { default } ::= { wfSyncEntry 96 } wfSyncPriority OBJECT-TYPE SYNTAX INTEGER(1..50) ACCESS read-write STATUS mandatory DESCRIPTION "Used by dial/switched services to assign priority of lines within the same demand or backup pool" DEFVAL { 1 } ::= { wfSyncEntry 97 } wfSyncTurboBofl OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } ACCESS read-write STATUS mandatory DESCRIPTION "DEBUG parameter - Turbo bofl enabled or disabled" DEFVAL { disabled } ::= { wfSyncEntry 98 } wfSyncBoflNum OBJECT-TYPE SYNTAX INTEGER(1..127) ACCESS read-write STATUS mandatory DESCRIPTION "DEBUG parameter - Number of breath of life packets per breath of life" DEFVAL { 1 } ::= { wfSyncEntry 99 } wfSyncBoflLen OBJECT-TYPE SYNTAX INTEGER(22..4450) ACCESS read-write STATUS mandatory DESCRIPTION "DEBUG parameter - breath of life packet length" DEFVAL { 200 } ::= { wfSyncEntry 100 } wfSyncTurboBoflMisses OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "DEBUG parameter - breath of life allocation failures" ::= { wfSyncEntry 101 } wfSyncTurboBoflInvocations OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "DEBUG parameter - breath of life invocations" ::= { wfSyncEntry 102 } wfSyncBandwidthOnDemandPool OBJECT-TYPE SYNTAX INTEGER(1..255) ACCESS read-write STATUS mandatory DESCRIPTION "Bandwidth pool id containing this line driver" ::= { wfSyncEntry 103 } wfSyncBODRecoverPeriodsToPass OBJECT-TYPE SYNTAX INTEGER(1..100) ACCESS read-write STATUS mandatory DESCRIPTION "This is the number of consecutive periods where the queue depth is below the congestion threshold required to declare the line congested. It is used for recovery. That is, once a line is declared as congested, this is the number of consecutive examination periods where the queue depth is below the recovery threshold value required to delare that the line is no longer congested." DEFVAL { 10 } ::= { wfSyncEntry 104 } wfSyncBODHistory OBJECT-TYPE SYNTAX DisplayString ACCESS read-only STATUS mandatory DESCRIPTION "DEBUG parameter - This is the SBOD history buffer." ::= { wfSyncEntry 105 } wfSyncBODDebugFlag OBJECT-TYPE SYNTAX INTEGER ACCESS read-write STATUS mandatory DESCRIPTION "DEBUG parameter - This is the SBOD Debug flag, used to control debug code for SBOD." ::= { wfSyncEntry 106 } wfSyncBChRateAdaption OBJECT-TYPE SYNTAX INTEGER { adaption64k(1), adaption128k(2) } ACCESS read-write STATUS mandatory DESCRIPTION "This attribute is only relevant when this Synchronous device driver is performing as an ISDN B channel over a BRI interface in leased line mode. This attribute specifies the piece of ISDN line's bandwidth which data from this driver will occupy. " DEFVAL { adaption64k } ::= { wfSyncEntry 107 } wfSyncBChActualRateAdaption OBJECT-TYPE SYNTAX INTEGER { adaption64k(1), adaption128k(2), adaption56kmsb(3), adaption56klsb(4) } ACCESS read-only STATUS mandatory DESCRIPTION "Indicates the current B Channel Rate Adaption in use. This attribute is only relevant when this Synchronous device driver is performing as an ISDN B channel over a BRI interface in leased line or dial-up mode. This attribute indicates the speed of this B-channel. It also specifies their bit positions for the case of 56K selections." ::= { wfSyncEntry 108 } wfSyncWanType OBJECT-TYPE SYNTAX INTEGER { synchronous(1), asynchronous(2), pasynchronous(3) } ACCESS read-write STATUS mandatory DESCRIPTION "This attribute indicates whether this port should be configured as a SYNCHRONOUS or UART/ASYNCHRONOUS interface." DEFVAL { synchronous } ::= { wfSyncEntry 109 } wfSyncAsyncBaudRate OBJECT-TYPE SYNTAX INTEGER { baudrate1200b(1200), baudrate2400b(2400), baudrate4800b(4800), baudrate7200b(7200), baudrate9600b(9600), baudrate12000b(12000), baudrate14400b(14400), baudrate19200b(19200), baudrate28800b(28800), baudrate38k(38400), baudrate56k(57600), baudrate64k(64000), baudrate76k(76800), baudrate96k(96000), baudrate115k(115200) } ACCESS read-write STATUS mandatory DESCRIPTION "Indicates the baud rate of the Tx/Rx character stream. This value should always be >= than speed at which the modems connect, but is independent of that speed. For instance, for V34 modems, the maximum modular connection speed is 28800 kbps. If your modems can do V.42 bis or MNP 5 data compression, with high (4 to 1) compression ratios you could fill a 115Kbps pipe." DEFVAL { baudrate9600b } ::= { wfSyncEntry 110 } wfSyncCfgAsyncCmndMaxIdles OBJECT-TYPE SYNTAX INTEGER(1..500) ACCESS read-write STATUS mandatory DESCRIPTION "Maximum number of idles we'll receive (in Command Mode) between ASYNC frames. Values other than zero over-ride the router selected values. A value of zero has a special meaning. Zero causes router based defaults to be used. This attribute is used to delineate frames when the QUICC is configured for UART/ASYNCHRONOUS mode." ::= { wfSyncEntry 111 } wfSyncAsyncCmndMaxIdles OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Maximum number of idles we'll receive (in Command Mode) (i.e. when the modems have not yet connected & entered data state), before closing the ASYNC frame. This value is used to delineate frames when receiving data when the SYNC port is configured for UART/ASYNCHRONOUS mode." ::= { wfSyncEntry 112 } wfSyncCfgAsyncDataMaxIdles OBJECT-TYPE SYNTAX INTEGER(1..500) ACCESS read-write STATUS mandatory DESCRIPTION "Maximum number of idles we'll receive (in Data Mode) between ASYNC frames. Values other than zero over-ride the router selected values. A value of zero has a special meaning. Zero causes router based defaults to be used. This attribute is used to delineate frames when the QUICC is configured for UART/ASYNCHRONOUS mode." ::= { wfSyncEntry 113 } wfSyncAsyncDataMaxIdles OBJECT-TYPE SYNTAX INTEGER ACCESS read-only STATUS mandatory DESCRIPTION "Maximum number of idles we'll receive (in Command Mode) (i.e. when the modems have connected & entered data state), before closing the ASYNC frame. This value is used to delineate frames when receiving data when the SYNC port is configured for UART/ASYNCHRONOUS mode." ::= { wfSyncEntry 114 } wfSyncFramesAbortTx OBJECT-TYPE SYNTAX Counter ACCESS read-only STATUS mandatory DESCRIPTION "Number of frames where CTS was lost during transmission." ::= { wfSyncEntry 115 } wfSyncPasyncParityType OBJECT-TYPE SYNTAX INTEGER { odd(1), even(2), high(3), low(4), none(5) } ACCESS read-write STATUS mandatory DESCRIPTION "Type of parity chosen for Polled Async" DEFVAL { even } ::= { wfSyncEntry 116 } wfSyncPasyncCharacterLength OBJECT-TYPE SYNTAX INTEGER { five(5), six(6), seven(7), eight(8) } ACCESS read-write STATUS mandatory DESCRIPTION "Number of data bits chosen for Polled Async" DEFVAL { eight } ::= { wfSyncEntry 117 } wfSyncPasyncStopLength OBJECT-TYPE SYNTAX INTEGER { one(1), two(2) } ACCESS read-write STATUS mandatory DESCRIPTION "Number of stop bits chosen for Polled Async" DEFVAL { two } ::= { wfSyncEntry 118 } wfSyncPasyncBaudRate OBJECT-TYPE SYNTAX INTEGER { baudrate150b(150), baudrate300b(300), baudrate600b(600), baudrate1200b(1200), baudrate2400b(2400), baudrate4800b(4800), baudrate7200b(7200), baudrate9600b(9600), baudrate12000b(12000), baudrate14400b(14400), baudrate19200b(19200), baudrate28800b(28800), baudrate38k(38400), baudrate56k(57600), baudrate64k(64000), baudrate76k(76800), baudrate96k(96000), baudrate115k(115200) } ACCESS read-write STATUS mandatory DESCRIPTION "Indicates the baud rate of the Tx/Rx character stream. This value should always be >= than speed at which the modems connect, but is independent of that speed. For instance, for V34 modems, the maximum modular connection speed is 28800 kbps. If your modems can do V.42 bis or MNP 5 data compression, with high (4 to 1) compression ratios you could fill a 115Kbps pipe." DEFVAL { baudrate600b } ::= { wfSyncEntry 119 } wfSyncLocalConnectionState OBJECT-TYPE SYNTAX INTEGER { up(1), down(2), unknown(3) } ACCESS read-only STATUS mandatory DESCRIPTION "The state of the cable at the router end." DEFVAL { unknown } ::= { wfSyncEntry 120 } wfSyncRemoteConnectionState OBJECT-TYPE SYNTAX INTEGER { up(1), down(2), devicestreaming(3), unknown(4) } ACCESS read-only STATUS mandatory DESCRIPTION "The state of the cable at the device end." DEFVAL { unknown } ::= { wfSyncEntry 121 } wfSyncTimeSlotAssignment OBJECT-TYPE SYNTAX DisplayString ACCESS read-only STATUS mandatory DESCRIPTION "Lists the time-slots which constitute this channel. Read only attribute that contains a list of time-slots from 1 to 24 used by the channel assigned to the FT1 card. It contains a list of the timeslots from 1 to 32 for the G.703 card." ::= { wfSyncEntry 122 } wfSyncEiaStatus OBJECT-TYPE SYNTAX INTEGER { txd(1), rxd(2), rts(4), cts(8), dsr(16), dcd(32), txc(64), rxc(128), dtr(256), txdToggled(65536), rxdToggled(131072), rtsToggled(262144), ctsToggled(524288), dsrToggled(1048576), dcdToggled(2097152), txcToggled(4194304), rxcToggled(8388608), dtrToggled(16777216) } ACCESS read-only STATUS mandatory DESCRIPTION "The state of the EIA signals at the router interface. The signals are designated as bits in this entry. If the signal is asserted, it is marked as a 1. If not asserted, it is marked as a 0. The state of each signal will be updated every second. Bits 0-15 are reserved for actual signal state. Bits 16-31 are reserved for indicating toggling of the signal. Toggling signals are indicated as a 1. Signals not toggling are indicated with a 0. The following signals are defined and monitored: The bit definition as as follows with bit #0 being the LSB. * signal status - bits 0-15 * bit 0 = TXD transmit data 1 = RXD receive data 2 = RTS request to send 3 = CTS clear to send 4 = DSR data set ready 5 = DCD data carrier detect 6 = TXC transmit clock 7 = RXC receive clock 8 = DTR data terminal ready. * signal toggle status bits 16-31 * bit 16 = TXD transmit data 17 = RXD receive data 18 = RTS request to send 19 = CTS clear to send 20 = DSR data set ready 21 = DCD data carrier detect 22 = TXC transmit clock 23 = RXC receive clock 24 = DTR data terminal ready." ::= { wfSyncEntry 123 } wfSyncEiaStatusReset OBJECT-TYPE SYNTAX INTEGER { reset(1), noaction(21) } ACCESS read-write STATUS mandatory DESCRIPTION "Reset The EIA status for the EIA signals in wfSyncEiaStatus. This is particularly useful for clearing the toggle status. " DEFVAL { noaction } ::= { wfSyncEntry 124 } wfSyncUcastMap OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } ACCESS read-write STATUS mandatory DESCRIPTION "Used to map ifEntry.ifInUcastPkts to wfSyncRxFrames and ifEntry.ifOutUcastPkts to wfSyncTxFrames." DEFVAL { enabled } ::= { wfSyncEntry 125 } END -- Wellfleet-SYNC-MIB