-- -- IRT4320DDA-MIB.my -- -- v4.4 20/09/2010 -- - added irt4320ddaDataRate > mbps270, asi, sdi -- - changed irt4320ddaDataRate > order of entries -- - changed irt4320ddaInvertInput ACCESS from read-only to read-write -- - changed descriptions -- v4.3 31/08/2010 -- - changed descriptions -- v4.2 26/08/2010 -- - removed irt4320ddaInputStatus -- - changed irt4320ddaAlarms > nonUrgentAlarm to aisDetected -- - changed irt4320ddaInputStatusTrap to irt4320ddaAlarmsTrap -- - changed irt4320ddaInputStatusTrapEn to irt4320ddaAlarmsTrapEn -- - changed descriptions -- v4.1 04/08/2010 -- - added enumeration entries for irt4320ddaReset -- - changed irt4320ddaInvertInput ACCESS from read-write to read-only -- v4.0 16/07/2010 -- - added irt4320ddaInputStatus, irt4320ddaInvertInput -- - changed irt4320ddaDataRateCtrl entries to snmp, pcbSwitches -- - changed irt4320ddaSignalStatus to irt4320ddaInputInfo -- - changed irt4320ddaSignalStatusTrapEn to irt4320ddaInputStatusTrapEn -- - changed irt4320ddaSignalStatusTrap to irt4320ddaInputStatusTrap -- - changed descriptions -- v3.0 25/05/2010 -- - added irt4320ddaSignalStatus > lockedSDI, lockedASI -- - changed order of entries in irt4320ddaSignalStatus -- v2.0 01/02/2010 -- - added irt4320ddaSignalStatus > aisDetected -- - added irt4320ddaOutputAIS, irt4320ddaChangeOnAIS -- - swapped irt4320ddaCableEQ, irt4320ddaDataRateCtrl -- - removed irt4320ddaAlarms > urgentAndNonUrgentAlarm -- - removed irt4320ddaKeepSignalAlive -- - changed descriptions -- v1.0 08/09/2009 -- - public issue IRT4320DDA-MIB DEFINITIONS ::= BEGIN IMPORTS irtProducts, irt FROM IRT-MIB OBJECT-TYPE FROM RFC-1212 TRAP-TYPE FROM RFC-1215 sysObjectID, sysName, DisplayString FROM RFC1213-MIB; -- -- Node definitions -- -- 1.3.6.1.4.1.16557.3.54 irt4320DDA OBJECT IDENTIFIER ::= { irtProducts 54 } -- 1.3.6.1.4.1.16557.3.54.1 irt4320ddaAlarms OBJECT-TYPE SYNTAX INTEGER { noAlarm(1), aisDetected(2), urgentAlarm(3) } ACCESS read-only STATUS mandatory DESCRIPTION "Status of the module's alarms. AIS detected: AIS detected in STM-1 data. Urgent alarm: Invalid input." ::= { irt4320DDA 1 } -- 1.3.6.1.4.1.16557.3.54.2 irt4320ddaModuleStatus OBJECT-TYPE SYNTAX INTEGER { main(1), standby(2) } ACCESS read-write STATUS mandatory DESCRIPTION "Operational status in relation to (optional) partner module. 1. Main: This module controls the shared outputs. To capture shared outputs, set this value. 2. Standby: Partner module controls the shared outputs. This value is not available to set. To release shared outputs, set partner module to Main." ::= { irt4320DDA 2 } -- 1.3.6.1.4.1.16557.3.54.3 irt4320ddaInputInfo OBJECT-TYPE SYNTAX INTEGER { notPresent(1), notLocked(2), locked(3), aisDetected(4), asiDetected(5), sdiDetected(6) } ACCESS read-only STATUS mandatory DESCRIPTION "Input status information. 1. Not present: Input not detected. 2. Not locked: Input present, but reclocker unlocked. 3. Locked: Reclocker locked to specified data rate. 4. AIS detected: AIS detected in STM-1 data. 5. ASI detected: ASI data stream detected. 6. SDI detected: SDI data stream detected." ::= { irt4320DDA 3 } -- 1.3.6.1.4.1.16557.3.54.4 irt4320ddaInvertInput OBJECT-TYPE SYNTAX INTEGER { disabled(1), enabled(2) } ACCESS read-write STATUS mandatory DESCRIPTION "Invert the input data before processing." ::= { irt4320DDA 4 } -- 1.3.6.1.4.1.16557.3.54.5 irt4320ddaDataRate OBJECT-TYPE SYNTAX INTEGER { stm1-cmi(1), stm1-nrz(2), mbps270(3), asi(4), sdi(5), asi-sdi(6) } ACCESS read-write STATUS mandatory DESCRIPTION "Input data rate. SW3-1, SW3-2, SW3-3 on the PCB override this SNMP setting." ::= { irt4320DDA 5 } -- 1.3.6.1.4.1.16557.3.54.6 irt4320ddaDataRateCtrl OBJECT-TYPE SYNTAX INTEGER { snmp(1), pcbSwitches(2) } ACCESS read-only STATUS mandatory DESCRIPTION "Indication that SW3-1, SW3-2, SW3-3 on the PCB are overriding the SNMP setting for the reclocker data rate." ::= { irt4320DDA 6 } -- 1.3.6.1.4.1.16557.3.54.7 irt4320ddaCableEQ OBJECT-TYPE SYNTAX INTEGER { normal(1), reduced(2) } ACCESS read-only STATUS mandatory DESCRIPTION "Amount of cable equalisation employed. Normal: Maximum available. Reduced: Lower gain for use in a noisy environment. SW3-4 on the PCB controls this setting." ::= { irt4320DDA 7 } -- 1.3.6.1.4.1.16557.3.54.8 irt4320ddaOutputAIS OBJECT-TYPE SYNTAX INTEGER { disabled(1), enabled(2) } ACCESS read-only STATUS mandatory DESCRIPTION "Output AIS in STM-1, upon loss of signal. SW3-5 on the PCB controls this setting." ::= { irt4320DDA 8 } -- 1.3.6.1.4.1.16557.3.54.9 irt4320ddaChangeOnAIS OBJECT-TYPE SYNTAX INTEGER { change(1), noChange(2) } ACCESS read-only STATUS mandatory DESCRIPTION "Attempt to changeover to the standby module upon detection of AIS in STM-1 input data. SW3-6 on the PCB controls this setting." ::= { irt4320DDA 9 } -- 1.3.6.1.4.1.16557.3.54.10 irt4320ddaModuleStatusTrapEn OBJECT-TYPE SYNTAX INTEGER { disabled(1), enabled(2) } ACCESS read-write STATUS mandatory DESCRIPTION "Send a trap upon change of module status, i.e. main <-> standby." ::= { irt4320DDA 10 } -- 1.3.6.1.4.1.16557.3.54.11 irt4320ddaAlarmsTrapEn OBJECT-TYPE SYNTAX INTEGER { disabled(1), enabled(2) } ACCESS read-write STATUS mandatory DESCRIPTION "Send a trap upon change of alarms status, i.e. invalid input or AIS." ::= { irt4320DDA 11 } -- 1.3.6.1.4.1.16557.3.54.12 irt4320ddaFirmwareVer OBJECT-TYPE SYNTAX DisplayString ACCESS read-only STATUS mandatory DESCRIPTION "Version of the FPGA firmware." ::= { irt4320DDA 12 } -- 1.3.6.1.4.1.16557.3.54.13 irt4320ddaSoftwareVer OBJECT-TYPE SYNTAX DisplayString ACCESS read-only STATUS mandatory DESCRIPTION "Version of the processor software." ::= { irt4320DDA 13 } -- 1.3.6.1.4.1.16557.3.54.14 irt4320ddaReset OBJECT-TYPE SYNTAX INTEGER { normal(1), reset(2) } ACCESS read-write STATUS mandatory DESCRIPTION "Reset the module to power-up default settings." ::= { irt4320DDA 14 } -- -- Trap definitions -- irt4320ddaModuleStatusTrap TRAP-TYPE ENTERPRISE irt VARIABLES { sysObjectID, sysName, irt4320ddaModuleStatus } DESCRIPTION "If enabled, a trap is sent upon change of module status, i.e. main <-> standby." ::= 54 irt4320ddaAlarmsTrap TRAP-TYPE ENTERPRISE irt VARIABLES { sysObjectID, sysName, irt4320ddaAlarms } DESCRIPTION "If enabled, a trap is sent upon change of alarms status, i.e. invalid input or AIS." ::= 182 END -- -- IRT4320DDA-MIB.my --