-- MIB file created 05-May-2011 12:01:11, by
--   SMICng version 2.2.11-beta(PRO)(Solaris), January 20, 2001. Enterprise key cisco.com

CISCO-MPLS-TE-STD-EXT-MIB DEFINITIONS ::= BEGIN

-- From file: "CISCO-MPLS-TE-STD-EXT-MIB.my"
-- Compile options "4 7 F H N W 03 06 0B 0G 0N 0T"

IMPORTS
    mplsTunnelIndex, mplsTunnelInstance, mplsTunnelIngressLSRId, 
    mplsTunnelEgressLSRId
            FROM MPLS-TE-STD-MIB
    ciscoMgmt
            FROM CISCO-SMI
    Counter, Gauge
            FROM RFC1155-SMI
    OBJECT-TYPE
            FROM RFC-1212;

cmplsTeStdExtMIB OBJECT IDENTIFIER ::= { ciscoMgmt 738 }
-- MODULE-IDENTITY
--  LastUpdated
--    201005270000Z
--  OrgName
--    Cisco Systems, Inc.
--  ContactInfo
--    Cisco Systems
--    Customer Service             
--    Postal: 170 W Tasman Drive             
--    San Jose, CA  95134             
--    USA             
--    Tel: +1 800 553-NETS             
--    E-mail: cs-snmp@cisco.com
--  Descr
--    This MIB module contains Cisco specific managed object
--    definitions for MPLS Traffic Engineering (TE), not contained in
--    MPLS-TE-STD-MIB.
--    The auto bandwidth feature enables MPLS TE Tunnels to adapt
--    automatically their bandwidth to their actual load.
--  RevDate
--    201005270000Z
--  RevDescr
--    Initial version of this MIB module.

cmplsTeStdExtMIBNotifs OBJECT IDENTIFIER ::= { cmplsTeStdExtMIB 0 }
cmplsTeStdExtMIBObjects OBJECT IDENTIFIER ::= { cmplsTeStdExtMIB 1 }
cmplsTeStdExtMIBConform OBJECT IDENTIFIER ::= { cmplsTeStdExtMIB 2 }
cmplsTeStdExtMIBCompliances OBJECT IDENTIFIER ::= { cmplsTeStdExtMIBConform 1 }
cmplsTeStdExtMIBGroups OBJECT IDENTIFIER ::= { cmplsTeStdExtMIBConform 2 }

CmplsTunnelBWPercent ::= Gauge(0..100)
-- TEXTUAL-CONVENTION
--  DspHint
--    d
--  Status
--    mandatory
--  Descr
--    A fraction of the bandwidth expressed in percentage.

cmplsTunnelAutoBWTable OBJECT-TYPE
    SYNTAX SEQUENCE OF CmplsTunnelAutoBWEntry
    ACCESS not-accessible
    STATUS mandatory
    DESCRIPTION
        "This table is used in order to manage auto bandwidth data.
        This table is sparse dependent on the mplsTunnelTable.  An entry
        in this table exists for each mplsTunnelEntry with a
        mplsTunnelRole of 'head' or 'headTail'. Each row contains
        auto-bandwidth data for the tunnel identified by the indexes
        defined later.
        An entry is created as soon as a 'head' or 'headTail' MPLS TE
        tunnel is configured in the system."
    ::= { cmplsTeStdExtMIBObjects 1 }

cmplsTunnelAutoBWEntry OBJECT-TYPE
    SYNTAX CmplsTunnelAutoBWEntry
    ACCESS not-accessible
    STATUS mandatory
    DESCRIPTION
        "A conceptual row in cmplsTunnelAutoBWTable. There is an entry
        in this table for each MPLS-TE tunnel with mplsTunnelRole 
        equals to 'head' or 'headTail'."
    INDEX { mplsTunnelIndex, mplsTunnelInstance, mplsTunnelIngressLSRId, mplsTunnelEgressLSRId }
    ::= { cmplsTunnelAutoBWTable 1 }

CmplsTunnelAutoBWEntry ::= SEQUENCE {
    cmplsTunnelAutoBWStatus INTEGER,
    cmplsTunnelAutoBWMin Gauge,
    cmplsTunnelAutoBWMax Gauge,
    cmplsTunnelAutoBWAdjThreshPercs CmplsTunnelBWPercent,
    cmplsTunnelAutoBWAdjThreshBW Gauge,
    cmplsTunnelAutoBWOverflowThreshPercs CmplsTunnelBWPercent,
    cmplsTunnelAutoBWOverflowThreshBW Gauge,
    cmplsTunnelAutoBWOverflowLimit Gauge,
    cmplsTunnelAutoBWUnderflowThreshPercs CmplsTunnelBWPercent,
    cmplsTunnelAutoBWUnderflowThreshBW Gauge,
    cmplsTunnelAutoBWUnderflowLimit Gauge,
    cmplsTunnelAutoBWApplicationFrequency Gauge,
    cmplsTunnelAutoBWCollectionFrequency Gauge,
    cmplsTunnelAutoBWLastAppliedBW Gauge,
    cmplsTunnelAutoBWApplications Counter,
    cmplsTunnelAutoBWLastApplicationTrigger INTEGER,
    cmplsTunnelAutoBWOverflowApplications Counter,
    cmplsTunnelAutoBWOverflowOccurrences Counter,
    cmplsTunnelAutoBWUnderflowApplications Counter,
    cmplsTunnelAutoBWUnderflowOccurrences Counter,
    cmplsTunnelAutoBWUnderflowHighestBW Gauge,
    cmplsTunnelAutoBWRequested Gauge,
    cmplsTunnelAutoBWSignaled Gauge,
    cmplsTunnelAutoBWCollectOnlyRequested Gauge,
    cmplsTunnelAutoBWHighest Gauge,
    cmplsTunnelAutoBWCollectedSamples Counter,
    cmplsTunnelAutoBWJitter Gauge,
    cmplsTunnelAutoBWAppRejectReason INTEGER
    }

cmplsTunnelAutoBWStatus OBJECT-TYPE
    SYNTAX INTEGER {
        autoBWDisabled(1),
        autoBWEnabled(2),
        autoBWCollectOnlyMode(3)
        }
    ACCESS read-only
    STATUS mandatory
    DESCRIPTION
        "This object indicates the operational status [or mode] of the
        auto bandwidth algorithm:
        
        - autoBWDisabled: The auto-bandwidth algorithm is not running;
        - autoBWEnabled: The auto-bandwidth algorithm is running;
        - autoBWCollectOnlyMode: The auto-bandwidth algorithm is
        running,
                                 but the bandwidth applications are 
                                 disabled;"
    DEFVAL { autoBWDisabled }
    ::= { cmplsTunnelAutoBWEntry 1 }

cmplsTunnelAutoBWMin OBJECT-TYPE
    SYNTAX Gauge
--  Units
--    kbps
    ACCESS read-write
    STATUS mandatory
    DESCRIPTION
        "This object specifies the minimum bandwidth that the
        auto-bandwidth algorithm can apply to a tunnel when the
        adjustment threshold is overcome.
        This object value is not aplicable if cmplsTunnelAutoBWStatus is
        'autoBWDisabled'."
    DEFVAL { 0 }
    ::= { cmplsTunnelAutoBWEntry 2 }

cmplsTunnelAutoBWMax OBJECT-TYPE
    SYNTAX Gauge
--  Units
--    kbps
    ACCESS read-write
    STATUS mandatory
    DESCRIPTION
        "This object specifies the maximum bandwidth that the
        auto-bandwidth algorithm can apply to a tunnel when the
        adjustment threshold is overcome.
        This object value is not aplicable if cmplsTunnelAutoBWStatus is
        'autoBWDisabled'."
    DEFVAL { 100 }
    ::= { cmplsTunnelAutoBWEntry 3 }

cmplsTunnelAutoBWAdjThreshPercs OBJECT-TYPE
    SYNTAX CmplsTunnelBWPercent
--    Rsyntax Gauge(0..100)
    ACCESS read-write
    STATUS mandatory
    DESCRIPTION
        "This object specifies the adjustment threshold percentage that
        needs to be overcome in order to trigger a new bandwidth
        application.
        This object value is not aplicable if cmplsTunnelAutoBWStatus is
        'autoBWDisabled'."
    DEFVAL { 10 }
    ::= { cmplsTunnelAutoBWEntry 4 }

cmplsTunnelAutoBWAdjThreshBW OBJECT-TYPE
    SYNTAX Gauge
--  Units
--    kbps
    ACCESS read-write
    STATUS mandatory
    DESCRIPTION
        "This object specifies the adjustment threshold bandwidth that
        needs to be overcome in order to trigger a new bandwidth
        application.
        This object value is not aplicable if cmplsTunnelAutoBWStatus is
        'autoBWDisabled'."
    DEFVAL { 10 }
    ::= { cmplsTunnelAutoBWEntry 5 }

cmplsTunnelAutoBWOverflowThreshPercs OBJECT-TYPE
    SYNTAX CmplsTunnelBWPercent
--    Rsyntax Gauge(0..100)
    ACCESS read-write
    STATUS mandatory
    DESCRIPTION
        "This object specifies the adjustment threshold percentage that
        needs to be overcome in order to trigger an overflow occurrence.
        If the application period has not completed when a
        cmplsTunnelAutoBWOverflowLimit overflow has occurred, a new
        bandwidth will be applied.
        This object value is not aplicable if cmplsTunnelAutoBWStatus is
        'autoBWDisabled'."
    DEFVAL { 10 }
    ::= { cmplsTunnelAutoBWEntry 6 }

cmplsTunnelAutoBWOverflowThreshBW OBJECT-TYPE
    SYNTAX Gauge
--  Units
--    kbps
    ACCESS read-write
    STATUS mandatory
    DESCRIPTION
        "This object specifies the adjustment threshold bandwidth that
        needs to be overcome in order to trigger an overflow occurrence.
        If the application period has not completed when a
        cmplsTunnelAutoBWOverflowLimit overflow has occurred, a new
        bandwidth will be applied.
        This object value is not aplicable if cmplsTunnelAutoBWStatus is
        'autoBWDisabled'."
    DEFVAL { 10 }
    ::= { cmplsTunnelAutoBWEntry 7 }

cmplsTunnelAutoBWOverflowLimit OBJECT-TYPE
    SYNTAX Gauge
    ACCESS read-write
    STATUS mandatory
    DESCRIPTION
        "This object specifies the number of consecutive collections
        exceeding overflow threshold.
        If the application period has not completed when a
        cmplsTunnelAutoBWOverflowLimit overflow has occurred, a new
        bandwidth will be applied.
        This object value is not aplicable if cmplsTunnelAutoBWStatus is
        'autoBWDisabled'."
    DEFVAL { 1 }
    ::= { cmplsTunnelAutoBWEntry 8 }

cmplsTunnelAutoBWUnderflowThreshPercs OBJECT-TYPE
    SYNTAX CmplsTunnelBWPercent
--    Rsyntax Gauge(0..100)
    ACCESS read-write
    STATUS mandatory
    DESCRIPTION
        "This object specifies the adjustment threshold percentage that
        needs to be overcome in order to trigger an underflow
        occurrence.
        If the application period has not completed when a
        cmplsTunnelAutoBWUnderflowLimit underflow has occurred, a new
        bandwidth will be applied.
        This object value is not aplicable if cmplsTunnelAutoBWStatus is
        'autoBWDisabled'."
    DEFVAL { 10 }
    ::= { cmplsTunnelAutoBWEntry 9 }

cmplsTunnelAutoBWUnderflowThreshBW OBJECT-TYPE
    SYNTAX Gauge
--  Units
--    kbps
    ACCESS read-write
    STATUS mandatory
    DESCRIPTION
        "This object specifies the adjustment threshold bandwidth that
        needs to be overcome in order to trigger an underflow
        occurrence.
        If the application period has not completed when a
        cmplsTunnelAutoBWUnderflowLimit underflow has occurred, a new
        bandwidth will be applied.
        This object value is not aplicable if cmplsTunnelAutoBWStatus is
        'autoBWDisabled'."
    DEFVAL { 1 }
    ::= { cmplsTunnelAutoBWEntry 10 }

cmplsTunnelAutoBWUnderflowLimit OBJECT-TYPE
    SYNTAX Gauge
    ACCESS read-write
    STATUS mandatory
    DESCRIPTION
        "This object specifies the number of consecutive collections
        under the underflow threshold.
        If the application period has not completed when a
        cmplsTunnelAutoBWUnderflowLimit underflow has occurred, a new
        bandwidth will be applied.
        This object value is not aplicable if cmplsTunnelAutoBWStatus is
        'autoBWDisabled'."
    DEFVAL { 1 }
    ::= { cmplsTunnelAutoBWEntry 11 }

cmplsTunnelAutoBWApplicationFrequency OBJECT-TYPE
    SYNTAX Gauge
--  Units
--    seconds
    ACCESS read-write
    STATUS mandatory
    DESCRIPTION
        "This object specifies the bandwidth application period.
        This object value is not aplicable if cmplsTunnelAutoBWStatus is
        'autoBWDisabled'."
    DEFVAL { 300 }
    ::= { cmplsTunnelAutoBWEntry 12 }

cmplsTunnelAutoBWCollectionFrequency OBJECT-TYPE
    SYNTAX Gauge
--  Units
--    seconds
    ACCESS read-write
    STATUS mandatory
    DESCRIPTION
        "This object specifies the sampling period for data rates.
        This object value is not aplicable if cmplsTunnelAutoBWStatus is
        'autoBWDisabled'."
    DEFVAL { 300 }
    ::= { cmplsTunnelAutoBWEntry 13 }

cmplsTunnelAutoBWLastAppliedBW OBJECT-TYPE
    SYNTAX Gauge
--  Units
--    kbps
    ACCESS read-only
    STATUS mandatory
    DESCRIPTION
        "This object indicates the last bandwidth applied by the
        auto-bandwidth algorithm.
        It will be set to zero if no bandwidth has been applied yet.
        If mplsTunnelInstance is zero this object will be set to zero.
        This object value is not aplicable if cmplsTunnelAutoBWStatus is
        'autoBWDisabled'."
    ::= { cmplsTunnelAutoBWEntry 14 }

cmplsTunnelAutoBWApplications OBJECT-TYPE
    SYNTAX Counter
    ACCESS read-only
    STATUS mandatory
    DESCRIPTION
        "This object indicates the number of auto bandwidths applied.
        If mplsTunnelInstance is zero this object will be set to zero.
        This object value is not aplicable if cmplsTunnelAutoBWStatus is
        'autoBWDisabled'."
    ::= { cmplsTunnelAutoBWEntry 15 }

cmplsTunnelAutoBWLastApplicationTrigger OBJECT-TYPE
    SYNTAX INTEGER {
        applicationNone(1),
        applicationPeriodic(2),
        applicationManual(3),
        applicationOverflow(4),
        applicationUnderflow(5)
        }
    ACCESS read-only
    STATUS mandatory
    DESCRIPTION
        "This object indicates the trigger reason for the last bandwidth
        application.
        If mplsTunnelInstance is zero this object will be set to
        'applicationNone'.
        This object value is not aplicable if cmplsTunnelAutoBWStatus is
        'autoBWDisabled'."
    ::= { cmplsTunnelAutoBWEntry 16 }

cmplsTunnelAutoBWOverflowApplications OBJECT-TYPE
    SYNTAX Counter
    ACCESS read-only
    STATUS mandatory
    DESCRIPTION
        "This object indicates the number of bandwidth applications
        due to overflow occurrences.
        If mplsTunnelInstance is zero this object will be set to zero.
        This object value is not aplicable if cmplsTunnelAutoBWStatus is
        'autoBWDisabled'."
    ::= { cmplsTunnelAutoBWEntry 17 }

cmplsTunnelAutoBWOverflowOccurrences OBJECT-TYPE
    SYNTAX Counter
    ACCESS read-only
    STATUS mandatory
    DESCRIPTION
        "This object indicates the number of overflow occurrences
        since last application period.
        If mplsTunnelInstance is zero this object will be set to zero.
        This object value is not aplicable if cmplsTunnelAutoBWStatus is
        'autoBWDisabled'."
    ::= { cmplsTunnelAutoBWEntry 18 }

cmplsTunnelAutoBWUnderflowApplications OBJECT-TYPE
    SYNTAX Counter
    ACCESS read-only
    STATUS mandatory
    DESCRIPTION
        "This object indicates the number of bandwidth applications due
        to underflow occurrences.
        If mplsTunnelInstance is zero this object will be set to zero.
        This object value is not aplicable if cmplsTunnelAutoBWStatus is
        'autoBWDisabled'."
    ::= { cmplsTunnelAutoBWEntry 19 }

cmplsTunnelAutoBWUnderflowOccurrences OBJECT-TYPE
    SYNTAX Counter
    ACCESS read-only
    STATUS mandatory
    DESCRIPTION
        "This object indicates the number of underflow occurrences
        since last application period.
        If mplsTunnelInstance is zero this object will be set to zero.
        This object value is not aplicable if cmplsTunnelAutoBWStatus is
        'autoBWDisabled'."
    ::= { cmplsTunnelAutoBWEntry 20 }

cmplsTunnelAutoBWUnderflowHighestBW OBJECT-TYPE
    SYNTAX Gauge
--  Units
--    kbps
    ACCESS read-only
    STATUS mandatory
    DESCRIPTION
        "This object indicates the highest sample collected during
        an underflow sequence.
        If mplsTunnelInstance is zero this object will be set to zero.
        This object value is not aplicable if cmplsTunnelAutoBWStatus is
        'autoBWDisabled'."
    ::= { cmplsTunnelAutoBWEntry 21 }

cmplsTunnelAutoBWRequested OBJECT-TYPE
    SYNTAX Gauge
--  Units
--    kpbs
    ACCESS read-only
    STATUS mandatory
    DESCRIPTION
        "This object indicates the bandwidth requested by the
        auto-bandwidth algorithm.
        If mplsTunnelInstance is zero this object will be set to zero.
        This object value is not aplicable if cmplsTunnelAutoBWStatus is
        'autoBWDisabled'."
    ::= { cmplsTunnelAutoBWEntry 22 }

cmplsTunnelAutoBWSignaled OBJECT-TYPE
    SYNTAX Gauge
--  Units
--    kpbs
    ACCESS read-only
    STATUS mandatory
    DESCRIPTION
        "This object indicates the bandwidth signaled by the
        auto-bandwidth algorithm.
        If mplsTunnelInstance is zero this object will be set to zero.
        This object value is not aplicable if cmplsTunnelAutoBWStatus is
        'autoBWDisabled'."
    ::= { cmplsTunnelAutoBWEntry 23 }

cmplsTunnelAutoBWCollectOnlyRequested OBJECT-TYPE
    SYNTAX Gauge
--  Units
--    kpbs
    ACCESS read-only
    STATUS mandatory
    DESCRIPTION
        "This object indicates the bandwidth that would have been
        requested by the auto-bandwidth algorithm if the auto-bandwidth
        functionality was enabled. If the collect only mode is enabled,
        the bandwidth change request will not be executed.
        If mplsTunnelInstance is zero this object will be set to zero.
        This object value is not aplicable if cmplsTunnelAutoBWStatus is
        'autoBWDisabled'."
    ::= { cmplsTunnelAutoBWEntry 24 }

cmplsTunnelAutoBWHighest OBJECT-TYPE
    SYNTAX Gauge
--  Units
--    kpbs
    ACCESS read-only
    STATUS mandatory
    DESCRIPTION
        "This object indicates the highest bandwidth sampled by
        the auto-bandwidth algorithm.
        If mplsTunnelInstance is zero this object will be set to zero.
        This object value is not aplicable if cmplsTunnelAutoBWStatus is
        'autoBWDisabled'."
    ::= { cmplsTunnelAutoBWEntry 25 }

cmplsTunnelAutoBWCollectedSamples OBJECT-TYPE
    SYNTAX Counter
    ACCESS read-only
    STATUS mandatory
    DESCRIPTION
        "This object indicates the samples collected since the last
        auto-bandwidth application.
        If mplsTunnelInstance is zero this object will be set to zero.
        This object value is not aplicable if cmplsTunnelAutoBWStatus is
        'autoBWDisabled'."
    ::= { cmplsTunnelAutoBWEntry 26 }

cmplsTunnelAutoBWJitter OBJECT-TYPE
    SYNTAX Gauge
    ACCESS read-only
    STATUS mandatory
    DESCRIPTION
        "This object indicates the auto-bandwidth application jitter.
        Jitter is the extra time to be added to the application interval
        the first time the auto bandwidth is applied.
        If mplsTunnelInstance is zero this object will be set to zero.
        This object value is not aplicable if cmplsTunnelAutoBWStatus is
        'autoBWDisabled'."
    DEFVAL { 0 }
    ::= { cmplsTunnelAutoBWEntry 27 }

cmplsTunnelAutoBWAppRejectReason OBJECT-TYPE
    SYNTAX INTEGER {
        applicationAllowed(1),
        autoBWDisabled(2),
        tunnelIsDown(3),
        tunnelIsFRR(4),
        tunnelIsBackup(5),
        tunnelIsLockDown(6)
        }
    ACCESS read-only
    STATUS mandatory
    DESCRIPTION
        "This object indicates the reason for the bandwidth application
        rejection.
        This object value is not aplicable if cmplsTunnelAutoBWStatus is
        'autoBWDisabled'."
    ::= { cmplsTunnelAutoBWEntry 28 }

cmplsTeStdExtMIBAutoBWObjectGroup OBJECT IDENTIFIER ::= { cmplsTeStdExtMIBGroups 1 }
-- OBJECT-GROUP
--  Status
--    mandatory
--  Descr
--    This contains the main MPLS TE extensions groups.
--  objects
--    cmplsTunnelAutoBWStatus, cmplsTunnelAutoBWMin, 
--    cmplsTunnelAutoBWMax, cmplsTunnelAutoBWAdjThreshPercs, 
--    cmplsTunnelAutoBWAdjThreshBW, 
--    cmplsTunnelAutoBWApplicationFrequency, 
--    cmplsTunnelAutoBWCollectionFrequency, 
--    cmplsTunnelAutoBWLastAppliedBW, cmplsTunnelAutoBWApplications, 
--    cmplsTunnelAutoBWLastApplicationTrigger, 
--    cmplsTunnelAutoBWOverflowApplications, 
--    cmplsTunnelAutoBWOverflowOccurrences, 
--    cmplsTunnelAutoBWUnderflowApplications, 
--    cmplsTunnelAutoBWUnderflowOccurrences, 
--    cmplsTunnelAutoBWUnderflowHighestBW, 
--    cmplsTunnelAutoBWRequested, cmplsTunnelAutoBWSignaled, 
--    cmplsTunnelAutoBWCollectOnlyRequested, 
--    cmplsTunnelAutoBWHighest, cmplsTunnelAutoBWCollectedSamples, 
--    cmplsTunnelAutoBWAppRejectReason

cmplsTeStdExtMIBAutoBWOptionalGroup OBJECT IDENTIFIER ::= { cmplsTeStdExtMIBGroups 2 }
-- OBJECT-GROUP
--  Status
--    mandatory
--  Descr
--    This contains the optional MPLS TE extensions groups.
--  objects
--    cmplsTunnelAutoBWOverflowThreshPercs, 
--    cmplsTunnelAutoBWOverflowThreshBW, 
--    cmplsTunnelAutoBWOverflowLimit, 
--    cmplsTunnelAutoBWUnderflowThreshPercs, 
--    cmplsTunnelAutoBWUnderflowThreshBW, 
--    cmplsTunnelAutoBWUnderflowLimit, cmplsTunnelAutoBWJitter

cmplsTeStdExtMIBCompliance OBJECT IDENTIFIER ::= { cmplsTeStdExtMIBCompliances 1 }
-- MODULE-COMPLIANCE
--  Status
--    mandatory
--  Descr
--    This is the main compliance statement for the MIB.
--  Module
--    >>current<<
--   OptGroup
--    cmplsTeStdExtMIBAutoBWOptionalGroup
--   OptGroup
--    cmplsTeStdExtMIBAutoBWObjectGroup


END