-- COPYRIGHT NOTICE
-- Copyright (c) Alteon WebSystems, Inc. 2001
-- All rights reserved
-- 
-- HISTORY
-- $Log: tigonNetwork.mib $
-- Revision ts90_rekha/2 2001/05/11 23:00:42 rekha
-- 	CR4320: Added MIB object ripStatRoutesAgedOut.
-- 
-- Revision jmoLatest_jamesob/2 2001/03/27 12:52:05 jamesob
-- 	CR10892 VRRP: Track HSRP bu VLAN (HSRV)
-- 	Added MIB objects to support tracking of
-- 	HSRP by vlan. New Objects: vrrpCurCfgVirtRtrTckHsrv,
-- 	vrrpNewCfgVirtRtrTckHsrv
-- 	Added mib objects to support HSRV priority increment.
-- 	New objects: vrrpCurCfgGenTckHsrvInc, vrrpNewCfgGenTckHsrvInc
-- 	Added vrrpCurCfgVirtRtrGrpTckHsrv and vrrpCurCfgVirtRtrGrpTckHsrv
-- 	to support vrrp group track hsrv
-- 
-- Revision work_rmundhra/3 2001/03/01 16:43:52 rmundhra
-- 	Fixed 10832: OIDs changed in mib.
-- 
-- Revision work_rmundhra/2 2001/03/01 00:30:03 rmundhra
-- 	Corrected the oids associated with ipFwdCurCfgLocalTable,
-- 	ipFwdNewCfgLocalTable, ipFwdCurCfgState & ipFwdNewCfgState and
-- 	unused oid's which are obsoleted. 
-- 
-- Revision genie_rekha/5 2001/02/27 20:17:16 rekha
-- 	Added SNMP support for BOOTP relay per IP interface.
-- 
-- Revision genie_rekha/2 2001/02/08 18:18:03 rekha
-- 	As part of the code cleanup split the Tigon MIB into smaller
-- 	modules. Instead of altswitch.mib these 5 new modules should be
-- 	used.
-- 
-- $EndLog$
-- 
-- Version 9.0.x
--

ALTEON-TS-NETWORK-MIB DEFINITIONS ::= BEGIN

IMPORTS
    IpAddress, Counter, Gauge 
        FROM RFC1155-SMI
    OBJECT-TYPE
        FROM RFC-1212
    PhysAddress, DisplayString
        FROM RFC1213-MIB
    switch 
        FROM ALTEON-ROOT-MIB
    stats, information
        FROM ALTEON-PRIVATE-MIBS;

iprouting	  OBJECT IDENTIFIER ::= { switch 3 }
vrrp              OBJECT IDENTIFIER ::= { switch 15 }

ripStats  	  OBJECT IDENTIFIER ::= { stats  1 }
arpStats  	  OBJECT IDENTIFIER ::= { stats  3 }
routeStats  	  OBJECT IDENTIFIER ::= { stats  4 }
dnsStats  	  OBJECT IDENTIFIER ::= { stats  5 }
vrrpStats         OBJECT IDENTIFIER ::= { stats  9 }

ip-info	  	  OBJECT IDENTIFIER ::= { information 3 }
vrrp-info         OBJECT IDENTIFIER ::= { information 4 }

-- IP Configuration

ipInterfaceTableMax OBJECT-TYPE
    SYNTAX  INTEGER
    ACCESS  read-only
    STATUS  mandatory
    DESCRIPTION
        "The maximum number of rows in the IP interface table."
    ::= { iprouting 1 }

ipCurCfgIntfTable OBJECT-TYPE
    SYNTAX  SEQUENCE OF IpCurCfgIntfEntry
    ACCESS  not-accessible
    STATUS  mandatory
    DESCRIPTION
        "The table of IP interface configuration."
    ::= { iprouting 2 }

ipCurCfgIntfEntry OBJECT-TYPE
    SYNTAX  IpCurCfgIntfEntry
    ACCESS  not-accessible
    STATUS  mandatory
    DESCRIPTION
        "A row in the Ip interface table"
    INDEX   { ipCurCfgIntfIndex }
    ::= { ipCurCfgIntfTable 1 }

IpCurCfgIntfEntry ::= SEQUENCE {
    ipCurCfgIntfIndex         INTEGER,
    ipCurCfgIntfAddr          IpAddress,
    ipCurCfgIntfMask          IpAddress,
    ipCurCfgIntfBroadcast     IpAddress,
    ipCurCfgIntfVlan          INTEGER,
    ipCurCfgIntfState         INTEGER,
    ipCurCfgIntfBootpRelay    INTEGER
    }
 
ipCurCfgIntfIndex OBJECT-TYPE
    SYNTAX  INTEGER  (1..64)
    ACCESS  read-only
    STATUS  mandatory
    DESCRIPTION
        "The interface number for which the IP information is related."
    ::= { ipCurCfgIntfEntry 1}

ipCurCfgIntfAddr OBJECT-TYPE
    SYNTAX  IpAddress
    ACCESS  read-only
    STATUS  mandatory
    DESCRIPTION
        "The IP address of the interface."
    ::= { ipCurCfgIntfEntry 2 }

ipCurCfgIntfMask OBJECT-TYPE
    SYNTAX  IpAddress
    ACCESS  read-only
    STATUS  mandatory  
    DESCRIPTION
        "The subnet mask of the interface."
    ::= { ipCurCfgIntfEntry 3 }

ipCurCfgIntfBroadcast OBJECT-TYPE
    SYNTAX  IpAddress
    ACCESS  read-only
    STATUS  mandatory  
    DESCRIPTION
        "The broadcast address of the interface."
    ::= { ipCurCfgIntfEntry 4 }

ipCurCfgIntfVlan OBJECT-TYPE
    SYNTAX  INTEGER (1..4094)
    ACCESS  read-only
    STATUS  mandatory  
    DESCRIPTION
        "The VLAN associated with the interface."
    ::= { ipCurCfgIntfEntry 5 }

ipCurCfgIntfState OBJECT-TYPE
    SYNTAX  INTEGER { 
	other(1),
	enabled(2),
	disabled(3)
	}
    ACCESS  read-only
    STATUS  mandatory  
    DESCRIPTION
        "The state of the interface."
    ::= { ipCurCfgIntfEntry 6 }

ipCurCfgIntfBootpRelay OBJECT-TYPE
    SYNTAX  INTEGER { 
	enabled(1),
	disabled(2)
	}
    ACCESS  read-only
    STATUS  mandatory  
    DESCRIPTION
        "Enable/disable BOOTP relay."
    ::= { ipCurCfgIntfEntry 7 }

ipNewCfgIntfTable OBJECT-TYPE
    SYNTAX  SEQUENCE OF IpNewCfgIntfEntry
    ACCESS  not-accessible
    STATUS  mandatory
    DESCRIPTION
        "The table of interface configuration in the New Configuration Block."
    ::= { iprouting 3 }

ipNewCfgIntfEntry OBJECT-TYPE
    SYNTAX  IpNewCfgIntfEntry
    ACCESS  not-accessible
    STATUS  mandatory
    DESCRIPTION
        "A row in the Ip interface table"
    INDEX   { ipNewCfgIntfIndex }
    ::= { ipNewCfgIntfTable 1 }
 
IpNewCfgIntfEntry ::= SEQUENCE {
    ipNewCfgIntfIndex         INTEGER,
    ipNewCfgIntfAddr          IpAddress,
    ipNewCfgIntfMask          IpAddress,
    ipNewCfgIntfBroadcast     IpAddress,
    ipNewCfgIntfVlan          INTEGER,
    ipNewCfgIntfState         INTEGER,
    ipNewCfgIntfDelete	      INTEGER,
    ipNewCfgIntfBootpRelay    INTEGER
    }
 
ipNewCfgIntfIndex OBJECT-TYPE
    SYNTAX  INTEGER  (1..64)
    ACCESS  read-only
    STATUS  mandatory
    DESCRIPTION
	"The interface number for which the IP information is related."
    ::= { ipNewCfgIntfEntry 1 }

ipNewCfgIntfAddr OBJECT-TYPE
    SYNTAX  IpAddress
    ACCESS  read-write
    STATUS  mandatory
    DESCRIPTION
        "The IP address of the interface."
    ::= { ipNewCfgIntfEntry 2 }

ipNewCfgIntfMask OBJECT-TYPE
    SYNTAX  IpAddress
    ACCESS  read-write
    STATUS  mandatory  
    DESCRIPTION
        "The subnet mask of the interface."
    ::= { ipNewCfgIntfEntry 3 }

ipNewCfgIntfBroadcast OBJECT-TYPE
    SYNTAX  IpAddress
    ACCESS  read-write
    STATUS  mandatory  
    DESCRIPTION
        "The broadcast address of the interface."
    ::= { ipNewCfgIntfEntry 4 }

ipNewCfgIntfVlan OBJECT-TYPE
    SYNTAX  INTEGER (1..4094)
    ACCESS  read-write
    STATUS  mandatory  
    DESCRIPTION
        "The VLAN associated with the interface."
    ::= { ipNewCfgIntfEntry 5 }

ipNewCfgIntfState OBJECT-TYPE
    SYNTAX  INTEGER { 
	other(1),
	enabled(2),
	disabled(3)
	}
    ACCESS  read-write
    STATUS  mandatory  
    DESCRIPTION
        "The state of the interface."
    ::= { ipNewCfgIntfEntry 6 }

ipNewCfgIntfDelete OBJECT-TYPE
    SYNTAX  INTEGER { 
	other(1),
        delete(2)
	}
    ACCESS  read-write
    STATUS  mandatory
    DESCRIPTION
        "When set to the value of 2 (delete), the entire row is deleted. 
         When read, other(1) is returned. Setting the value to anything 
         other than 2(delete) has no effect on the state of the row."
    ::= { ipNewCfgIntfEntry 7 }

ipNewCfgIntfBootpRelay OBJECT-TYPE
    SYNTAX  INTEGER { 
	enabled(1),
	disabled(2)
	}
    ACCESS  read-write
    STATUS  mandatory  
    DESCRIPTION
        "Enable/disable BOOTP relay."
    ::= { ipNewCfgIntfEntry 8 }

-- IP Gateway Table Configuration

ipGatewayTableMax OBJECT-TYPE
    SYNTAX  INTEGER
    ACCESS  read-only
    STATUS  mandatory
    DESCRIPTION
        "The maximum number of rows in the IP gateway table."
    ::= { iprouting 4 }

ipCurCfgGwTable OBJECT-TYPE
    SYNTAX  SEQUENCE OF IpCurCfgGwEntry
    ACCESS  not-accessible
    STATUS  mandatory
    DESCRIPTION
        "The table of gateways  in the Current configuration Block."
    ::= { iprouting 5 }

ipCurCfgGwEntry OBJECT-TYPE
    SYNTAX  IpCurCfgGwEntry
    ACCESS  not-accessible
    STATUS  mandatory
    DESCRIPTION
        "A row in the Ip gateway table"
    INDEX   { ipCurCfgGwIndex }
    ::= { ipCurCfgGwTable 1 }

IpCurCfgGwEntry ::= SEQUENCE {
    ipCurCfgGwIndex         INTEGER,
    ipCurCfgGwAddr          IpAddress,
    ipCurCfgGwInterval      INTEGER,
    ipCurCfgGwRetry         INTEGER,
    ipCurCfgGwState         INTEGER,
    ipCurCfgGwArp           INTEGER
    }

ipCurCfgGwIndex OBJECT-TYPE
    SYNTAX  INTEGER  (1..4)
    ACCESS  read-only
    STATUS  mandatory
    DESCRIPTION
        "The gateway number for which the information is related."
    ::= { ipCurCfgGwEntry 1}

ipCurCfgGwAddr OBJECT-TYPE
    SYNTAX  IpAddress
    ACCESS  read-only
    STATUS  mandatory
    DESCRIPTION
        "The IP address of the default gateway."
    ::= { ipCurCfgGwEntry 2 }

ipCurCfgGwInterval OBJECT-TYPE 
    SYNTAX  INTEGER (1..60)
    ACCESS  read-only 
    STATUS  mandatory 
    DESCRIPTION 
        "The interval between ping attempts." 
    ::= { ipCurCfgGwEntry 3 }

ipCurCfgGwRetry OBJECT-TYPE
    SYNTAX  INTEGER (1..120)   
    ACCESS  read-only
    STATUS  mandatory
    DESCRIPTION
        "The number of failed attempts to declare the default gateway DOWN."
    ::= { ipCurCfgGwEntry 4 }

ipCurCfgGwState OBJECT-TYPE
    SYNTAX  INTEGER {
        other(1),
        enabled(2),
        disabled(3)
	}  
    ACCESS  read-only
    STATUS  mandatory
    DESCRIPTION
        "The state of the default gateway."
    ::= { ipCurCfgGwEntry 5 }

ipCurCfgGwArp OBJECT-TYPE
    SYNTAX  INTEGER {
        other(1),
        enabled(2),
        disabled(3)
        } 
    ACCESS  read-only
    STATUS  mandatory
    DESCRIPTION
        "The state of ARP only health checks."
    ::= { ipCurCfgGwEntry 6 }

ipNewCfgGwTable OBJECT-TYPE
    SYNTAX  SEQUENCE OF IpNewCfgGwEntry
    ACCESS  not-accessible
    STATUS  mandatory
    DESCRIPTION
        "The table of gateway configuration in the new configuration block."
    ::= { iprouting 6 }

ipNewCfgGwEntry OBJECT-TYPE
    SYNTAX  IpNewCfgGwEntry
    ACCESS  not-accessible
    STATUS  mandatory
    DESCRIPTION
        "A row in the Ip default gateway table"
    INDEX   { ipNewCfgGwIndex }
    ::= { ipNewCfgGwTable 1 }

IpNewCfgGwEntry ::= SEQUENCE {
    ipNewCfgGwIndex         INTEGER,
    ipNewCfgGwAddr          IpAddress,
    ipNewCfgGwInterval      INTEGER,
    ipNewCfgGwRetry         INTEGER,
    ipNewCfgGwState         INTEGER,
    ipNewCfgGwDelete        INTEGER,
    ipNewCfgGwArp           INTEGER
    }

ipNewCfgGwIndex OBJECT-TYPE
    SYNTAX  INTEGER  (1..4)
    ACCESS  read-only
    STATUS  mandatory
    DESCRIPTION
        "The gateway number for which the information is related."
    ::= { ipNewCfgGwEntry 1}

ipNewCfgGwAddr OBJECT-TYPE
    SYNTAX  IpAddress
    ACCESS  read-write
    STATUS  mandatory
    DESCRIPTION
        "The IP address of the default gateway."
    ::= { ipNewCfgGwEntry 2 }

ipNewCfgGwInterval OBJECT-TYPE 
    SYNTAX  INTEGER (1..60)
    ACCESS  read-write 
    STATUS  mandatory 
    DESCRIPTION 
        "The interval in seconds between ping attempts." 
    ::= { ipNewCfgGwEntry 3 }

ipNewCfgGwRetry OBJECT-TYPE
    SYNTAX  INTEGER (1..120)   
    ACCESS  read-write
    STATUS  mandatory
    DESCRIPTION
        "The number of failed attempts to declare the default gateway DOWN."
    ::= { ipNewCfgGwEntry 4 }

ipNewCfgGwState OBJECT-TYPE
    SYNTAX  INTEGER {
	other(1),
        enabled(2),
        disabled(3)
	}
    ACCESS  read-write
    STATUS  mandatory
    DESCRIPTION
        "The state of the default gateway."
    ::= { ipNewCfgGwEntry 5 }

ipNewCfgGwDelete OBJECT-TYPE
    SYNTAX  INTEGER {
	other(1),
        delete(2)
        }
    ACCESS  read-write
    STATUS  mandatory
    DESCRIPTION
        "When set to the value of 2 (delete), the entire row is deleted. 
         When read, other is returned. Setting the value to anything other 
         than 2(delete) has no effect on the state of the row."
    ::= { ipNewCfgGwEntry 6 }

ipNewCfgGwArp OBJECT-TYPE
    SYNTAX  INTEGER {
        other(1),
        enabled(2),
        disabled(3)
        }
    ACCESS  read-write
    STATUS  mandatory
    DESCRIPTION
        "The state of the ARP only health checks."
    ::= { ipNewCfgGwEntry 7 }

ipCurCfgStaticRouteTable OBJECT-TYPE
    SYNTAX  SEQUENCE OF IpCurCfgStaticRouteEntry
    ACCESS  not-accessible
    STATUS  mandatory
    DESCRIPTION
        "The table of static routes in the current configuration block."
    ::= { iprouting 7 }

ipCurCfgStaticRouteEntry OBJECT-TYPE
    SYNTAX  IpCurCfgStaticRouteEntry
    ACCESS  not-accessible
    STATUS  mandatory
    DESCRIPTION
        "A row in the static IP route table"
    INDEX   { ipCurCfgStaticRouteIndx }
    ::= { ipCurCfgStaticRouteTable 1 }

IpCurCfgStaticRouteEntry ::= SEQUENCE {
    ipCurCfgStaticRouteIndx         INTEGER,
    ipCurCfgStaticRouteDestIp       IpAddress,
    ipCurCfgStaticRouteMask         IpAddress,
    ipCurCfgStaticRouteGateway      IpAddress,
    ipCurCfgStaticRouteInterface    INTEGER
    }

ipCurCfgStaticRouteIndx OBJECT-TYPE
    SYNTAX  INTEGER (1..64)
    ACCESS  read-only
    STATUS  mandatory
    DESCRIPTION
        "The index of the static routing table."
    ::= { ipCurCfgStaticRouteEntry 1}

ipCurCfgStaticRouteDestIp OBJECT-TYPE
    SYNTAX  IpAddress
    ACCESS  read-only
    STATUS  mandatory
    DESCRIPTION
        "The destination IP address of this route."
    ::= { ipCurCfgStaticRouteEntry 2}

ipCurCfgStaticRouteMask OBJECT-TYPE 
    SYNTAX  IpAddress
    ACCESS  read-only 
    STATUS  mandatory 
    DESCRIPTION 
        "The destination IP address of this route."
    ::= { ipCurCfgStaticRouteEntry 3}

ipCurCfgStaticRouteGateway OBJECT-TYPE 
    SYNTAX  IpAddress
    ACCESS  read-only 
    STATUS  mandatory 
    DESCRIPTION 
        "The destination IP address of this route."
    ::= { ipCurCfgStaticRouteEntry 4}

ipCurCfgStaticRouteInterface OBJECT-TYPE 
    SYNTAX  INTEGER
    ACCESS  read-only 
    STATUS  mandatory 
    DESCRIPTION 
        "The IP interface of this route.  The IP address of the specified 
         interface shall be use as source IP when performs routing."
    ::= { ipCurCfgStaticRouteEntry 5}

ipNewCfgStaticRouteTable OBJECT-TYPE
    SYNTAX  SEQUENCE OF IpNewCfgStaticRouteEntry
    ACCESS  not-accessible
    STATUS  mandatory
    DESCRIPTION
        "The table of static routes in the new configuration block."
    ::= { iprouting 8 }

ipNewCfgStaticRouteEntry OBJECT-TYPE
    SYNTAX  IpNewCfgStaticRouteEntry
    ACCESS  not-accessible
    STATUS  mandatory
    DESCRIPTION
        "A row in the static IP route table"
    INDEX   { ipNewCfgStaticRouteIndx }
    ::= { ipNewCfgStaticRouteTable 1 }

IpNewCfgStaticRouteEntry ::= SEQUENCE {
    ipNewCfgStaticRouteIndx         INTEGER,
    ipNewCfgStaticRouteDestIp       IpAddress,
    ipNewCfgStaticRouteMask         IpAddress,
    ipNewCfgStaticRouteGateway      IpAddress,
    ipNewCfgStaticRouteAction       INTEGER,
    ipNewCfgStaticRouteInterface    INTEGER
    }

ipNewCfgStaticRouteIndx OBJECT-TYPE
    SYNTAX  INTEGER (1..64)
    ACCESS  read-only
    STATUS  mandatory
    DESCRIPTION
        "The index of the static routing table."
    ::= { ipNewCfgStaticRouteEntry 1}

ipNewCfgStaticRouteDestIp OBJECT-TYPE
    SYNTAX  IpAddress
    ACCESS  read-write
    STATUS  mandatory
    DESCRIPTION
        "The destination IP address of this route."
    ::= { ipNewCfgStaticRouteEntry 2}

ipNewCfgStaticRouteMask OBJECT-TYPE 
    SYNTAX  IpAddress
    ACCESS  read-write 
    STATUS  mandatory 
    DESCRIPTION 
        "The subnet mask of this route."
    ::= { ipNewCfgStaticRouteEntry 3}

ipNewCfgStaticRouteGateway OBJECT-TYPE 
    SYNTAX  IpAddress
    ACCESS  read-write 
    STATUS  mandatory 
    DESCRIPTION 
        "The IP address of the gateway for this route."
    ::= { ipNewCfgStaticRouteEntry 4}

ipNewCfgStaticRouteAction OBJECT-TYPE
    SYNTAX  INTEGER {
        other(1),
        delete(2)
       }  
    ACCESS  read-write
    STATUS  mandatory
    DESCRIPTION
        "When set to the value of 2 (delete), the entire row is deleted. 
         When read, other is returned. Setting the value to anything other 
         than 2(delete) has no effect on the state of the row."
    ::= { ipNewCfgStaticRouteEntry 5 }

ipNewCfgStaticRouteInterface OBJECT-TYPE 
    SYNTAX  INTEGER
    ACCESS  read-write 
    STATUS  mandatory 
    DESCRIPTION 
        "The IP interface of this route.  The IP address of the specified 
         interface shall be use as source IP when performs routing."
    ::= { ipNewCfgStaticRouteEntry 6 }

-- Forwarding group 

ipForward         OBJECT IDENTIFIER ::= { iprouting 9 }
ripConfig	  OBJECT IDENTIFIER ::= { ipForward 1 }

ripCurCfgSupply OBJECT-TYPE
    SYNTAX  INTEGER {
	other(1),
	enabled(2),	
	disabled(3)
	}
    ACCESS  read-only
    STATUS  mandatory
    DESCRIPTION
        "Enable or disable supplying route updates."
    ::= { ripConfig 1 }

ripNewCfgSupply OBJECT-TYPE
    SYNTAX  INTEGER {
	other(1),
        enabled(2),
        disabled(3)
        }
    ACCESS  read-write
    STATUS  mandatory
    DESCRIPTION
        "Enable or disable supplying route updates."
    ::= { ripConfig 2 }

ripCurCfgListen OBJECT-TYPE 
    SYNTAX  INTEGER {
	other(1),
        enabled(2),      
        disabled(3) 
	}
    ACCESS  read-only 
    STATUS  mandatory  
    DESCRIPTION 
        "Enable or disable listening to route updates." 
    ::= { ripConfig 3 }

ripNewCfgListen OBJECT-TYPE
    SYNTAX  INTEGER {
	other(1),
        enabled(2),
        disabled(3)
	}
    ACCESS  read-write
    STATUS  mandatory
    DESCRIPTION
        "Enable or disable listening to route updates."
    ::= { ripConfig 4 }

ripCurCfgDefListen OBJECT-TYPE 
    SYNTAX  INTEGER {
	other(1),
        enabled(2),      
        disabled(3) 
	}
    ACCESS  read-only 
    STATUS  mandatory  
    DESCRIPTION 
        "Enable or disable listening to default routes." 
    ::= { ripConfig 5 }

ripNewCfgDefListen OBJECT-TYPE
    SYNTAX  INTEGER {
	other(1),
        enabled(2),
        disabled(3)
	}
    ACCESS  read-write
    STATUS  mandatory
    DESCRIPTION
        "Enable or disable listening to default routes."
    ::= { ripConfig 6 }

ripCurCfgStaticSupply OBJECT-TYPE 
    SYNTAX  INTEGER {
	other(1),
        enabled(2),      
        disabled(3) 
	}
    ACCESS  read-only 
    STATUS  mandatory  
    DESCRIPTION 
        "Enable or disable supplying static route updates." 
    ::= { ripConfig 7 }

ripNewCfgStaticSupply OBJECT-TYPE
    SYNTAX  INTEGER {
	other(1),
        enabled(2),
        disabled(3)
	}
    ACCESS  read-write
    STATUS  mandatory
    DESCRIPTION
        "Enable or disable supplying static route updates."
    ::= { ripConfig 8 }

ripCurCfgUpdatePeriod OBJECT-TYPE
    SYNTAX  INTEGER  (1..120)
    ACCESS  read-only
    STATUS  mandatory
    DESCRIPTION
        "Update Period in seconds."
    ::= { ripConfig 9 }

ripNewCfgUpdatePeriod OBJECT-TYPE
    SYNTAX  INTEGER (1..120)
    ACCESS  read-write
    STATUS  mandatory
    DESCRIPTION
        "Update period in seconds."
    ::= { ripConfig 10 }

ripCurCfgState OBJECT-TYPE
    SYNTAX  INTEGER {
	other(1),
        on(2),
        off(3)
        }
    ACCESS  read-only
    STATUS  mandatory
    DESCRIPTION
        "RIP global state."
    ::= { ripConfig 11 }

ripNewCfgState OBJECT-TYPE
    SYNTAX  INTEGER {
	other(1),
        on(2),
        off(3)
        }
    ACCESS  read-write
    STATUS  mandatory
    DESCRIPTION
        "Globally turn RIP on or off."
    ::= { ripConfig 12 }

ripCurCfgPoisonReverse OBJECT-TYPE
    SYNTAX  INTEGER {
	other(1),
        enabled(2),
        disabled(3)
	}
    ACCESS  read-only
    STATUS  mandatory
    DESCRIPTION
        "RIP poison reverse."
    ::= { ripConfig 13 }
 
ripNewCfgPoisonReverse OBJECT-TYPE
    SYNTAX  INTEGER {
	other(1),
        enabled(2),
        disabled(3)
	}
    ACCESS  read-write
    STATUS  mandatory
    DESCRIPTION
        "RIP poison reverse."
    ::= { ripConfig 14 }

-- Table to turn on/off forwarding per port

ipFwdCurCfgPortTable OBJECT-TYPE
    SYNTAX  SEQUENCE OF IpFwdCurCfgPortEntry
    ACCESS  not-accessible
    STATUS  mandatory
    DESCRIPTION
        "The table of ports and their forwarding states"
    ::= { ipForward 2 }

ipFwdCurCfgPortEntry OBJECT-TYPE
    SYNTAX  IpFwdCurCfgPortEntry
    ACCESS  not-accessible
    STATUS  mandatory
    DESCRIPTION
        "A row in the ipFwdCurCfgPortTable "
    INDEX   { ipFwdCurCfgPortIndex }
    ::= { ipFwdCurCfgPortTable 1 }

IpFwdCurCfgPortEntry ::= SEQUENCE {
    ipFwdCurCfgPortIndex	INTEGER,
    ipFwdCurCfgPortState	INTEGER
    }

ipFwdCurCfgPortIndex OBJECT-TYPE
    SYNTAX  INTEGER
    ACCESS  read-only
    STATUS  mandatory
    DESCRIPTION
        "The port number for which the forwarding state information pertains."
    ::= { ipFwdCurCfgPortEntry 1 }
 
ipFwdCurCfgPortState OBJECT-TYPE
    SYNTAX  INTEGER {
	other(1),
	enabled(2),
	disabled(3)
        }
    ACCESS  read-only
    STATUS  mandatory
    DESCRIPTION
        "The forwarding state of the port."
    ::= { ipFwdCurCfgPortEntry 2 }

ipFwdNewCfgPortTable OBJECT-TYPE
    SYNTAX  SEQUENCE OF IpFwdNewCfgPortEntry
    ACCESS  not-accessible
    STATUS  mandatory
    DESCRIPTION
        "The table of ports and their forwarding states"
    ::= { ipForward 3 }
 
ipFwdNewCfgPortEntry OBJECT-TYPE
    SYNTAX  IpFwdNewCfgPortEntry
    ACCESS  not-accessible
    STATUS  mandatory
    DESCRIPTION
        "A row in the ipFwdNewCfgPortTable "
    INDEX   { ipFwdNewCfgPortIndex }
    ::= { ipFwdNewCfgPortTable 1 }
 
IpFwdNewCfgPortEntry ::= SEQUENCE {
    ipFwdNewCfgPortIndex           INTEGER,
    ipFwdNewCfgPortState           INTEGER
    }
 
ipFwdNewCfgPortIndex OBJECT-TYPE
    SYNTAX  INTEGER
    ACCESS  read-only
    STATUS  mandatory
    DESCRIPTION
        "The port number for which the forwarding state information pertains."
    ::= { ipFwdNewCfgPortEntry 1 }
 
ipFwdNewCfgPortState OBJECT-TYPE
    SYNTAX  INTEGER {
	other(1),
        enabled(2),
        disabled(3)
        }
    ACCESS  read-write  
    STATUS  mandatory
    DESCRIPTION
        "The forwarding state of the port."
    ::= { ipFwdNewCfgPortEntry 2 }

--The following oid's are obsoleted and should not be used
--ipFwdCurCfgLocalSubnet  OBJECT IDENTIFIER ::= { ipForward 4 }   obsoleted
--ipFwdNewCfgLocalSubnet  OBJECT IDENTIFIER ::= { ipForward 5 }   obsoleted
--ipFwdCurCfgLocalMask    OBJECT IDENTIFIER ::= { ipForward 6 }   obsoleted
--ipFwdNewCfgLocalMask    OBJECT IDENTIFIER ::= { ipForward 7 }   obsoleted

ipFwdCurCfgLocalTable OBJECT-TYPE
    SYNTAX  SEQUENCE OF IpFwdCurCfgLocalEntry
    ACCESS  not-accessible
    STATUS  mandatory
    DESCRIPTION
        "The table of local network definition."
    ::= { ipForward 14 }

ipFwdCurCfgLocalEntry OBJECT-TYPE
    SYNTAX  IpFwdCurCfgLocalEntry
    ACCESS  not-accessible
    STATUS  mandatory
    DESCRIPTION
        "A row in the ipFwdCurCfgLocalTable "
    INDEX   { ipFwdCurCfgLocalIndex }
    ::= { ipFwdCurCfgLocalTable 1 }

IpFwdCurCfgLocalEntry ::= SEQUENCE {
    ipFwdCurCfgLocalIndex	INTEGER,
    ipFwdCurCfgLocalSubnet	IpAddress,
    ipFwdCurCfgLocalMask	IpAddress
    }

ipFwdCurCfgLocalIndex OBJECT-TYPE
    SYNTAX  INTEGER (1..5) 
    ACCESS  read-only
    STATUS  mandatory
    DESCRIPTION
        "The index of ipFwdCurCfgLocalTable."
    ::= { ipFwdCurCfgLocalEntry 1 }

ipFwdCurCfgLocalSubnet OBJECT-TYPE
    SYNTAX  IpAddress
    ACCESS  read-only
    STATUS  mandatory
    DESCRIPTION
        "The current local IP subnet."
    ::= { ipFwdCurCfgLocalEntry 2 }

ipFwdCurCfgLocalMask OBJECT-TYPE 
    SYNTAX  IpAddress 
    ACCESS  read-only 
    STATUS  mandatory
    DESCRIPTION 
        "The current local IP subnet mask." 
    ::= { ipFwdCurCfgLocalEntry 3 } 
 
ipFwdNewCfgLocalTable OBJECT-TYPE
    SYNTAX  SEQUENCE OF IpFwdNewCfgLocalEntry
    ACCESS  not-accessible
    STATUS  mandatory
    DESCRIPTION
        "The table of local network definition."
    ::= { ipForward 15 }

ipFwdNewCfgLocalEntry OBJECT-TYPE
    SYNTAX  IpFwdNewCfgLocalEntry
    ACCESS  not-accessible
    STATUS  mandatory
    DESCRIPTION
        "A row in the ipFwdNewCfgLocalTable "
    INDEX   { ipFwdNewCfgLocalIndex }
    ::= { ipFwdNewCfgLocalTable 1 }

IpFwdNewCfgLocalEntry ::= SEQUENCE {
    ipFwdNewCfgLocalIndex	INTEGER,
    ipFwdNewCfgLocalSubnet	IpAddress,
    ipFwdNewCfgLocalMask	IpAddress,
    ipFwdNewCfgLocalDelete      INTEGER
    }

ipFwdNewCfgLocalIndex OBJECT-TYPE
    SYNTAX  INTEGER (1..5) 
    ACCESS  read-only
    STATUS  mandatory
    DESCRIPTION
        "The index of ipFwdNewCfgLocalTable."
    ::= { ipFwdNewCfgLocalEntry 1 }

ipFwdNewCfgLocalSubnet OBJECT-TYPE 
    SYNTAX  IpAddress 
    ACCESS  read-write 
    STATUS  mandatory
    DESCRIPTION 
        "The new local IP subnet." 
    ::= { ipFwdNewCfgLocalEntry 2 }

ipFwdNewCfgLocalMask OBJECT-TYPE  
    SYNTAX  IpAddress  
    ACCESS  read-write  
    STATUS  mandatory
    DESCRIPTION  
        "The new local IP subnet mask."  
    ::= { ipFwdNewCfgLocalEntry 3 }

ipFwdNewCfgLocalDelete OBJECT-TYPE
    SYNTAX INTEGER { 
        other(1),
        delete(2)
	}
    ACCESS read-write
    STATUS mandatory
    DESCRIPTION
        "When set to the value of 2 (delete), the entire row is deleted. 
         When read, other(1) is returned. Setting the value to anything 
         other than 2(delete) has no effect on the state of the row."
    ::= { ipFwdNewCfgLocalEntry 4 }

ipFwdCurCfgState OBJECT-TYPE
    SYNTAX  INTEGER {
        other(1),
        on(2),
        off(3)
	}
    ACCESS  read-only
    STATUS  mandatory
    DESCRIPTION
        "IP forwarding global state."
    ::= { ipForward 8 }

ipFwdNewCfgState OBJECT-TYPE
    SYNTAX  INTEGER { 
	other(1), 
        on(2),
        off(3) 
	}
    ACCESS  read-write
    STATUS  mandatory  
    DESCRIPTION 
        "IP forwarding global state." 
    ::= { ipForward 9 }

ipFwdCurCfgDirectedBcast OBJECT-TYPE
    SYNTAX INTEGER {
        enabled(2),
        disabled(3)
	}
    ACCESS read-only
    STATUS mandatory
    DESCRIPTION
        "Enable or disable forwarding directed broadcasts."
    ::= { ipForward 10 }

ipFwdNewCfgDirectedBcast OBJECT-TYPE
    SYNTAX INTEGER {
        enabled(2),
        disabled(3)
	}
    ACCESS read-write
    STATUS mandatory
    DESCRIPTION
        "Enable or disable forwarding directed broadcasts."
    ::= { ipForward 11 }

ipFwdPortTableMaxSize OBJECT-TYPE
    SYNTAX INTEGER
    ACCESS read-only
    STATUS mandatory
    DESCRIPTION
        "The maximum number of rows in the IP Port table."
    ::= { ipForward 12 }

ipFwdLocalTableMaxSize OBJECT-TYPE
    SYNTAX INTEGER
    ACCESS read-only
    STATUS mandatory
    DESCRIPTION
        "The maximum number of rows in the Local table."
    ::= { ipForward 13 }

arpCurCfgReARPPeriod OBJECT-TYPE
    SYNTAX INTEGER (2..120)
    ACCESS read-only
    STATUS mandatory
    DESCRIPTION
        "Re-ARP Period in seconds."
    ::= { iprouting 10 }

arpNewCfgReARPPeriod OBJECT-TYPE 
    SYNTAX  INTEGER (2..120)
    ACCESS  read-write
    STATUS  mandatory 
    DESCRIPTION 
        "Re-ARP Period in seconds." 
    ::= { iprouting 11 }

ipCurCfgGwMetric OBJECT-TYPE
    SYNTAX  INTEGER {
        strict(1),
        roundrobin(2)
        }  
    ACCESS  read-only
    STATUS  mandatory
    DESCRIPTION
        "The default gateway metric."
    ::= { iprouting 12 }

ipNewCfgGwMetric OBJECT-TYPE
    SYNTAX  INTEGER {
        strict(1),
        roundrobin(2)
        }  
    ACCESS  read-write
    STATUS  mandatory
    DESCRIPTION
        "The default gateway metric."
    ::= { iprouting 13 }

ipCurCfgBootpAddr OBJECT-TYPE
    SYNTAX  IpAddress
    ACCESS  read-only
    STATUS  mandatory
    DESCRIPTION
        "The IP address of BOOTP server."
    ::= { iprouting 14 }

ipNewCfgBootpAddr OBJECT-TYPE
    SYNTAX  IpAddress
    ACCESS  read-write
    STATUS  mandatory
    DESCRIPTION
        "The IP address of BOOTP server."
    ::= { iprouting 15 }

ipCurCfgBootpAddr2 OBJECT-TYPE
    SYNTAX  IpAddress
    ACCESS  read-only
    STATUS  mandatory
    DESCRIPTION
        "The IP address of second BOOTP server."
    ::= { iprouting 16 }

ipNewCfgBootpAddr2 OBJECT-TYPE
    SYNTAX  IpAddress
    ACCESS  read-write
    STATUS  mandatory
    DESCRIPTION
        "The IP address of second BOOTP server."
    ::= { iprouting 17 }

ipCurCfgBootpState OBJECT-TYPE
    SYNTAX  INTEGER {
	other(1),
        enabled(2),
        disabled(3)
        }
    ACCESS  read-only
    STATUS  mandatory
    DESCRIPTION
        "The state of BOOTP relay."
    ::= { iprouting 18 }

ipNewCfgBootpState OBJECT-TYPE
    SYNTAX  INTEGER {
	other(1),
        enabled(2),
        disabled(3)
        }
    ACCESS  read-write  
    STATUS  mandatory
    DESCRIPTION
        "The state of BOOTP relay."
    ::= { iprouting 19 }

ipStaticRouteTableMaxSize OBJECT-TYPE
    SYNTAX  INTEGER
    ACCESS  read-only
    STATUS  mandatory
    DESCRIPTION
        "The maximum number of rows in the Static Route table."
    ::= { iprouting 20 }

-- VRRP (Virtual Router Redundantcy Protocol) Group

vrrpGeneral       OBJECT IDENTIFIER ::= { vrrp 1 }

vrrpCurCfgGenState OBJECT-TYPE
    SYNTAX  INTEGER {
        enabled(1),
        disabled(2)
        }
    ACCESS  read-only
    STATUS  mandatory
    DESCRIPTION
        "Enable or disable VRRP operation globally."
    ::= { vrrpGeneral 1 }

vrrpNewCfgGenState OBJECT-TYPE
    SYNTAX  INTEGER {
        enabled(1),
        disabled(2)
        }
    ACCESS  read-write
    STATUS  mandatory
    DESCRIPTION
        "Enable or disable VRRP operation globally."
    ::= { vrrpGeneral 2 }

vrrpCurCfgGenTckVirtRtrInc OBJECT-TYPE
    SYNTAX  INTEGER (0..254)
    ACCESS  read-only
    STATUS  mandatory
    DESCRIPTION
        "The increment of VRRP virtual router priority. The priority is 
         adjusted by tracking the state of other virtual routers."
    ::= { vrrpGeneral 3 }

vrrpNewCfgGenTckVirtRtrInc OBJECT-TYPE
    SYNTAX  INTEGER (0..254)
    ACCESS  read-write
    STATUS  mandatory
    DESCRIPTION
        "The increment of VRRP virtual router priority. The priority is 
         adjusted by tracking the state of other virtual routers."
    ::= { vrrpGeneral 4 }

vrrpCurCfgGenTckIpIntfInc OBJECT-TYPE
    SYNTAX  INTEGER (0..254)
    ACCESS  read-only
    STATUS  mandatory
    DESCRIPTION
        "The increment of VRRP virtual router priority. The priority is 
         adjusted by tracking the state of other router interfaces."
    ::= { vrrpGeneral 5 }

vrrpNewCfgGenTckIpIntfInc OBJECT-TYPE
    SYNTAX  INTEGER (0..254)
    ACCESS  read-write
    STATUS  mandatory
    DESCRIPTION
        "The increment of VRRP virtual router priority. The priority is 
         adjusted by tracking the state of other router interfaces."
    ::= { vrrpGeneral 6 }

vrrpCurCfgGenTckVlanPortInc OBJECT-TYPE
    SYNTAX  INTEGER (0..254)
    ACCESS  read-only
    STATUS  mandatory
    DESCRIPTION
        "The increment of VRRP virtual router priority. The priority is 
         adjusted by tracking the port state of ports that belongs to the 
         same virtual LAN as the virtual router."
    ::= { vrrpGeneral 7 }

vrrpNewCfgGenTckVlanPortInc OBJECT-TYPE
    SYNTAX  INTEGER (0..254)
    ACCESS  read-write
    STATUS  mandatory
    DESCRIPTION
        "The increment of VRRP virtual router priority. The priority is 
         adjusted by tracking the port state of ports that belongs to the 
         same virtual LAN as the virtual router."
    ::= { vrrpGeneral 8 }

vrrpCurCfgGenTckL4PortInc OBJECT-TYPE
    SYNTAX  INTEGER (0..254)
    ACCESS  read-only
    STATUS  mandatory
    DESCRIPTION
        "The increment of VRRP virtual router priority. The priority is 
         adjusted by tracking the Layer 4 port states. This is valid when 
         virtual server is configured as a VRRP virtual router."
    ::= { vrrpGeneral 9 }

vrrpNewCfgGenTckL4PortInc OBJECT-TYPE
    SYNTAX  INTEGER (0..254)
    ACCESS  read-write
    STATUS  mandatory
    DESCRIPTION
        "The increment of VRRP virtual router priority. The priority is 
         adjusted by tracking the Layer 4 port states. This is valid when 
         virtual server is configured as a VRRP virtual router."
    ::= { vrrpGeneral 10 }

vrrpCurCfgGenTckRServerInc OBJECT-TYPE
    SYNTAX  INTEGER (0..254)
    ACCESS  read-only
    STATUS  mandatory
    DESCRIPTION
        "The increment of VRRP virtual router priority. The priority is 
         adjusted by tracking the state of real servers under the virtual 
         server which is configured as a VRRP virtual router."
    ::= { vrrpGeneral 11 }

vrrpNewCfgGenTckRServerInc OBJECT-TYPE
    SYNTAX  INTEGER (0..254)
    ACCESS  read-write
    STATUS  mandatory
    DESCRIPTION
        "The increment of VRRP virtual router priority. The priority is 
         adjusted by tracking the state of real servers under the virtual 
         server which is configured as a VRRP virtual router."
    ::= { vrrpGeneral 12 }

vrrpCurCfgGenTckHsrpInc OBJECT-TYPE
    SYNTAX  INTEGER (0..254)
    ACCESS  read-only
    STATUS  mandatory
    DESCRIPTION
        "The increment of VRRP virtual router priority.  The
	 priority is adjusted by tracking the HSRP advertisements."
    ::= { vrrpGeneral 13 }

vrrpNewCfgGenTckHsrpInc OBJECT-TYPE
    SYNTAX  INTEGER (0..254)
    ACCESS  read-write
    STATUS  mandatory
    DESCRIPTION
        "The increment of VRRP virtual router priority.  The
         priority is adjusted by tracking the HSRP advertisements."
    ::= { vrrpGeneral 14 }

vrrpCurCfgGenHotstandby OBJECT-TYPE
    SYNTAX  INTEGER {
        enabled(1),
        disabled(2)
        }
    ACCESS  read-only
    STATUS  mandatory
    DESCRIPTION
        "Enable or disable hotstandby processing."
    ::= { vrrpGeneral 15 }

vrrpNewCfgGenHotstandby OBJECT-TYPE
    SYNTAX  INTEGER {
        enabled(1),
        disabled(2)
        }
    ACCESS  read-write
    STATUS  mandatory
    DESCRIPTION
        "Enable or disable hotstandby processing."
    ::= { vrrpGeneral 16 }

vrrpCurCfgGenTckHsrvInc OBJECT-TYPE
        SYNTAX  INTEGER (0..254)
        ACCESS  read-only
        STATUS  mandatory
        DESCRIPTION
                "The increment of VRRP virtual router priority.  The
                 priority is adjusted by tracking the HSRP advertisements
                 by VLAN."
        ::= { vrrpGeneral 17 }
 
vrrpNewCfgGenTckHsrvInc OBJECT-TYPE
        SYNTAX  INTEGER (0..254)
        ACCESS  read-write
        STATUS  mandatory
        DESCRIPTION
                "The increment of VRRP virtual router priority.  The
                 priority is adjusted by tracking the HSRP advertisements
                 by VLAN."
        ::= { vrrpGeneral 18 }

vrrpCurCfgVirtRtrTable OBJECT-TYPE
    SYNTAX  SEQUENCE OF VrrpCurCfgVirtRtrTableEntry
    ACCESS  not-accessible
    STATUS  mandatory
    DESCRIPTION
        "The table of VRRP virtual routers configuration in current_config."
    ::= { vrrp 2 }
 
vrrpCurCfgVirtRtrTableEntry OBJECT-TYPE
    SYNTAX  VrrpCurCfgVirtRtrTableEntry
    ACCESS  not-accessible
    STATUS  mandatory
    DESCRIPTION
        "Information about a VRRP virtual router."
    INDEX   { vrrpCurCfgVirtRtrIndx }
    ::= { vrrpCurCfgVirtRtrTable 1 }
 
VrrpCurCfgVirtRtrTableEntry ::= SEQUENCE {
    vrrpCurCfgVirtRtrIndx         INTEGER,
    vrrpCurCfgVirtRtrID           INTEGER,
    vrrpCurCfgVirtRtrAddr         IpAddress,
    vrrpCurCfgVirtRtrIfIndex      INTEGER,
    vrrpCurCfgVirtRtrInterval     INTEGER,
    vrrpCurCfgVirtRtrPriority     INTEGER,
    vrrpCurCfgVirtRtrPreempt      INTEGER,
    vrrpCurCfgVirtRtrState        INTEGER,
    vrrpCurCfgVirtRtrSharing      INTEGER,
    vrrpCurCfgVirtRtrTckVirtRtr   INTEGER,
    vrrpCurCfgVirtRtrTckIpIntf    INTEGER,
    vrrpCurCfgVirtRtrTckVlanPort  INTEGER,
    vrrpCurCfgVirtRtrTckL4Port    INTEGER,
    vrrpCurCfgVirtRtrTckRServer   INTEGER,
    vrrpCurCfgVirtRtrTckHsrp      INTEGER,
    vrrpCurCfgVirtRtrTckHsrv      INTEGER
    }

vrrpCurCfgVirtRtrIndx OBJECT-TYPE
    SYNTAX  INTEGER
    ACCESS  read-only
    STATUS  mandatory
    DESCRIPTION
        "The VRRP virtual router table index."
    ::= { vrrpCurCfgVirtRtrTableEntry 1 }

vrrpCurCfgVirtRtrID OBJECT-TYPE
    SYNTAX  INTEGER (1..255)
    ACCESS  read-only
    STATUS  mandatory
    DESCRIPTION
        "The VRRP virtual router identifier."
    ::= { vrrpCurCfgVirtRtrTableEntry 2 }

vrrpCurCfgVirtRtrAddr OBJECT-TYPE
    SYNTAX  IpAddress
    ACCESS  read-only
    STATUS  mandatory
    DESCRIPTION
        "The VRRP virtual router IP address."
    ::= { vrrpCurCfgVirtRtrTableEntry 3 }

vrrpCurCfgVirtRtrIfIndex OBJECT-TYPE
    SYNTAX  INTEGER
    ACCESS  read-only
    STATUS  mandatory
    DESCRIPTION
        "The IfIndex that the VRRP virtual router is representing."
    ::= { vrrpCurCfgVirtRtrTableEntry 4 }

vrrpCurCfgVirtRtrInterval OBJECT-TYPE
    SYNTAX  INTEGER (1..255)
    ACCESS  read-only
    STATUS  mandatory
    DESCRIPTION
        "The time interval between VRRP advertisements in seconds."
    ::= { vrrpCurCfgVirtRtrTableEntry 5 }

vrrpCurCfgVirtRtrPriority OBJECT-TYPE
    SYNTAX  INTEGER (1..254)
    ACCESS  read-only
    STATUS  mandatory
    DESCRIPTION
        "The priority value to be used by the specified VRRP virtual routers."
    ::= { vrrpCurCfgVirtRtrTableEntry 6 }

vrrpCurCfgVirtRtrPreempt OBJECT-TYPE
    SYNTAX  INTEGER {
        enabled(1),
        disabled(2)
        }
    ACCESS  read-only
    STATUS  mandatory
    DESCRIPTION
        "This is for controlling whether a higher priority Backup
          VRRP virtual router preempts a low priority Master.

          enabled(1)  - allow preemption
          disabled(2) - prohibit preemption"
    ::= { vrrpCurCfgVirtRtrTableEntry 7 }

vrrpCurCfgVirtRtrState OBJECT-TYPE
    SYNTAX  INTEGER {
        enabled(1),
        disabled(2)
        }
    ACCESS  read-only
    STATUS  mandatory
    DESCRIPTION
        "Enable or disable the VRRP virtual router."
    ::= { vrrpCurCfgVirtRtrTableEntry 8 }

vrrpCurCfgVirtRtrSharing OBJECT-TYPE
    SYNTAX  INTEGER {
        enabled(1),
        disabled(2)
        }
    ACCESS  read-only
    STATUS  mandatory
    DESCRIPTION
        "Enable or disable load sharing of non-master virtual router."
    ::= { vrrpCurCfgVirtRtrTableEntry 9 }

vrrpCurCfgVirtRtrTckVirtRtr OBJECT-TYPE
    SYNTAX  INTEGER {
        enabled(1),
        disabled(2)
        }
    ACCESS  read-only
    STATUS  mandatory
    DESCRIPTION
        "Enable or disable tracking other virtual routers for priority 
         adjustment. The priority increment is defined 
         in vrrpCurCfgGenTckVirtRtrInc."
    ::= { vrrpCurCfgVirtRtrTableEntry 10 }

vrrpCurCfgVirtRtrTckIpIntf OBJECT-TYPE
    SYNTAX  INTEGER {
        enabled(1),
        disabled(2)
        }
    ACCESS  read-only
    STATUS  mandatory
    DESCRIPTION
        "Enable or disable tracking other router interfaces for 
	 priority adjustment. The priority increment is defined 
	 in vrrpCurCfgGenTckIpIntfInc."
    ::= { vrrpCurCfgVirtRtrTableEntry 11 }

vrrpCurCfgVirtRtrTckVlanPort OBJECT-TYPE
    SYNTAX  INTEGER {
        enabled(1),
        disabled(2)
        }
    ACCESS  read-only
    STATUS  mandatory
    DESCRIPTION
        "Enable or disable tracking port state of VLAN ports 
	 for priority adjustment. The priority increment is 
	 defined in vrrpCurCfgGenTckVlanPortInc."
    ::= { vrrpCurCfgVirtRtrTableEntry 12 }

vrrpCurCfgVirtRtrTckL4Port OBJECT-TYPE
    SYNTAX  INTEGER {
        enabled(1),
        disabled(2)
        }
    ACCESS  read-only
    STATUS  mandatory
    DESCRIPTION
        "Enable or disable tracking Layer 4 port states for 
	 priority adjustment.  the priority increment is defined 
	 in vrrpCurCfgGenTckL4PortInc.  This is applied when 
	 virtual server is configured as a VRRP virtual router."
    ::= { vrrpCurCfgVirtRtrTableEntry 13 }

vrrpCurCfgVirtRtrTckRServer OBJECT-TYPE
    SYNTAX  INTEGER {
        enabled(1),
        disabled(2)
        }
    ACCESS  read-only
    STATUS  mandatory
    DESCRIPTION
        "Enable or disable tracking real server states for 
	 priority adjustment.  the priority increment is defined 
	 in vrrpCurCfgGenTckRServerInc.  This is applied when 
	 virtual server is configured as a VRRP virtual router."
    ::= { vrrpCurCfgVirtRtrTableEntry 14 }

vrrpCurCfgVirtRtrTckHsrp OBJECT-TYPE
    SYNTAX  INTEGER {
        enabled(1),
        disabled(2)
        }
    ACCESS  read-only
    STATUS  mandatory
    DESCRIPTION
        "Enable or disable tracking HSRP advertisements for 
	 priority adjustment.  the priority increment is defined 
	 in vrrpCurCfgGenTckHsrpInc.  This is applied when 
	 virtual server is configured as a VRRP virtual router."
    ::= { vrrpCurCfgVirtRtrTableEntry 15 }

vrrpCurCfgVirtRtrTckHsrv OBJECT-TYPE
        SYNTAX  INTEGER {
                enabled(1),
                disabled(2)
                }
        ACCESS  read-only
        STATUS  mandatory
        DESCRIPTION
                "Enable or disable tracking HSRP advertisements by VLAN for
                 priority adjustment.  The priority increment is defined
                 in vrrpCurCfgGenTckHsrvInc.  This is applied when
                 virtual server is configured as a VRRP virtual router."
        ::= { vrrpCurCfgVirtRtrTableEntry 16 }

vrrpNewCfgVirtRtrTable OBJECT-TYPE
    SYNTAX  SEQUENCE OF VrrpNewCfgVirtRtrTableEntry
    ACCESS  not-accessible
    STATUS  mandatory
    DESCRIPTION
        "The table of VRRP virtual routers configuration in current_config."
    ::= { vrrp 3 }

vrrpNewCfgVirtRtrTableEntry OBJECT-TYPE
    SYNTAX  VrrpNewCfgVirtRtrTableEntry
    ACCESS  not-accessible
    STATUS  mandatory
    DESCRIPTION
        "Information about a VRRP virtual router."
    INDEX   { vrrpNewCfgVirtRtrIndx }
    ::= { vrrpNewCfgVirtRtrTable 1 }

VrrpNewCfgVirtRtrTableEntry ::= SEQUENCE {
    vrrpNewCfgVirtRtrIndx         INTEGER,
    vrrpNewCfgVirtRtrID           INTEGER,
    vrrpNewCfgVirtRtrAddr         IpAddress,
    vrrpNewCfgVirtRtrIfIndex      INTEGER,
    vrrpNewCfgVirtRtrInterval     INTEGER,
    vrrpNewCfgVirtRtrPriority     INTEGER,
    vrrpNewCfgVirtRtrPreempt      INTEGER,
    vrrpNewCfgVirtRtrState        INTEGER,
    vrrpNewCfgVirtRtrDelete       INTEGER,
    vrrpNewCfgVirtRtrSharing      INTEGER,
    vrrpNewCfgVirtRtrTckVirtRtr   INTEGER,
    vrrpNewCfgVirtRtrTckIpIntf    INTEGER,
    vrrpNewCfgVirtRtrTckVlanPort  INTEGER,
    vrrpNewCfgVirtRtrTckL4Port    INTEGER,
    vrrpNewCfgVirtRtrTckRServer   INTEGER,
    vrrpNewCfgVirtRtrTckHsrp      INTEGER,
    vrrpNewCfgVirtRtrTckHsrv      INTEGER
    }

vrrpNewCfgVirtRtrIndx OBJECT-TYPE
    SYNTAX  INTEGER
    ACCESS  read-only
    STATUS  mandatory
    DESCRIPTION
        "The VRRP virtual router table index."
    ::= { vrrpNewCfgVirtRtrTableEntry 1 }

vrrpNewCfgVirtRtrID OBJECT-TYPE
    SYNTAX  INTEGER (1..255)
    ACCESS  read-write
    STATUS  mandatory
    DESCRIPTION
        "The VRRP virtual router identifier."
    ::= { vrrpNewCfgVirtRtrTableEntry 2 }

vrrpNewCfgVirtRtrAddr OBJECT-TYPE
    SYNTAX  IpAddress
    ACCESS  read-write
    STATUS  mandatory
    DESCRIPTION
        "The VRRP virtual router IP address."
    ::= { vrrpNewCfgVirtRtrTableEntry 3 }

vrrpNewCfgVirtRtrIfIndex OBJECT-TYPE
    SYNTAX  INTEGER
    ACCESS  read-write
    STATUS  mandatory
    DESCRIPTION
        "The IfIndex that the VRRP virtual router is representing."
   ::= { vrrpNewCfgVirtRtrTableEntry 4 }

vrrpNewCfgVirtRtrInterval OBJECT-TYPE
    SYNTAX  INTEGER (1..255)
    ACCESS  read-write
    STATUS  mandatory
    DESCRIPTION
        "The time interval between VRRP advertisements in seconds."
    ::= { vrrpNewCfgVirtRtrTableEntry 5 }

vrrpNewCfgVirtRtrPriority OBJECT-TYPE
    SYNTAX  INTEGER (1..254)
    ACCESS  read-write
    STATUS  mandatory
    DESCRIPTION
        "The priority value to be used by the specified VRRP virtual router."
    ::= { vrrpNewCfgVirtRtrTableEntry 6 }

vrrpNewCfgVirtRtrPreempt OBJECT-TYPE
    SYNTAX  INTEGER {
        enabled(1),
        disabled(2)
        }
    ACCESS  read-write
    STATUS  mandatory
    DESCRIPTION
        "This is for controlling whether a higher priority Backup
         VRRP virtual router preempts a low priority Master.

         enabled(1)  - allow preemption
         disabled(2) - prohibit preemption"
    ::= { vrrpNewCfgVirtRtrTableEntry 7 }

vrrpNewCfgVirtRtrState OBJECT-TYPE
    SYNTAX  INTEGER {
        enabled(1),
        disabled(2)
        }
    ACCESS  read-write
    STATUS  mandatory
    DESCRIPTION
        "Enable or disable the VRRP virtual router."
    ::= { vrrpNewCfgVirtRtrTableEntry 8 }

vrrpNewCfgVirtRtrDelete OBJECT-TYPE
    SYNTAX  INTEGER { 
	other(1),
        delete(2)
	}
    ACCESS  read-write
    STATUS  mandatory
    DESCRIPTION
        "When set to the value of 2 (delete), the entire row is deleted. 
         When read, other(1) is returned. Setting the value to anything 
         other than delete(2) has no effect on the state of the row."
    ::= { vrrpNewCfgVirtRtrTableEntry 9 }

vrrpNewCfgVirtRtrSharing OBJECT-TYPE
    SYNTAX  INTEGER {
        enabled(1),
        disabled(2)
        }
    ACCESS  read-write
    STATUS  mandatory
    DESCRIPTION
        "Enable or disable load sharing of non-master virtual router."
    ::= { vrrpNewCfgVirtRtrTableEntry 10 }

vrrpNewCfgVirtRtrTckVirtRtr OBJECT-TYPE
    SYNTAX  INTEGER {
        enabled(1),
        disabled(2)
        }
    ACCESS  read-write
    STATUS  mandatory
    DESCRIPTION
        "Enable or disable tracking other virtual routers for 
	 priority adjustment.  the priority increment is defined 
	 in vrrpNewCfgGenTckVirtRtrInc."
    ::= { vrrpNewCfgVirtRtrTableEntry 11 }

vrrpNewCfgVirtRtrTckIpIntf OBJECT-TYPE
    SYNTAX  INTEGER {
        enabled(1),
        disabled(2)
        }
     ACCESS  read-write
     STATUS  mandatory
     DESCRIPTION
         "Enable or disable tracking other router interfaces for 
	  priority adjustment.  the priority increment is defined 
	  in vrrpNewCfgGenTckIpIntfInc."
    ::= { vrrpNewCfgVirtRtrTableEntry 12 }

vrrpNewCfgVirtRtrTckVlanPort OBJECT-TYPE
    SYNTAX  INTEGER {
        enabled(1),
        disabled(2)
        }
    ACCESS  read-write
    STATUS  mandatory
    DESCRIPTION
        "Enable or disable tracking port state of VLAN ports 
	 for priority adjustment.  the priority increment is 
	 defined in vrrpNewCfgGenTckVlanPortInc."
    ::= { vrrpNewCfgVirtRtrTableEntry 13 }

vrrpNewCfgVirtRtrTckL4Port OBJECT-TYPE
    SYNTAX  INTEGER {
        enabled(1),
        disabled(2)
        }
     ACCESS  read-write
     STATUS  mandatory
     DESCRIPTION
         "Enable or disable tracking Layer 4 port states for 
	  priority adjustment.  the priority increment is defined 
	  in vrrpNewCfgGenTckL4PortInc.  This is applied when 
	  virtual server is configured as a VRRP virtual router."
    ::= { vrrpNewCfgVirtRtrTableEntry 14 }

vrrpNewCfgVirtRtrTckRServer OBJECT-TYPE
    SYNTAX  INTEGER {
        enabled(1),
        disabled(2)
        }
    ACCESS  read-write
    STATUS  mandatory
    DESCRIPTION
        "Enable or disable tracking real server states for 
	 priority adjustment.  the priority increment is defined 
	 in vrrpNewCfgGenTckRServerInc.  This is applied when 
	 virtual server is configured as a VRRP virtual router."
    ::= { vrrpNewCfgVirtRtrTableEntry 15 }

vrrpNewCfgVirtRtrTckHsrp OBJECT-TYPE
    SYNTAX  INTEGER {
        enabled(1),
        disabled(2)
        }
    ACCESS  read-write
    STATUS  mandatory
    DESCRIPTION
        "Enable or disable tracking HSRP advertisements for 
	 priority adjustment.  the priority increment is defined 
	 in vrrpNewCfgGenTckHsrpInc.  This is applied when 
	 virtual server is configured as a VRRP virtual router."
    ::= { vrrpNewCfgVirtRtrTableEntry 16 }

vrrpNewCfgVirtRtrTckHsrv OBJECT-TYPE
        SYNTAX  INTEGER {
                enabled(1),
                disabled(2)
                }
        ACCESS  read-write
        STATUS  mandatory
        DESCRIPTION
                "Enable or disable tracking HSRP by VLAN advertisements for
                 priority adjustment.  The priority increment is defined
                 in vrrpNewCfgGenTckHsrvInc.  This is applied when
                 virtual server is configured as a VRRP virtual router."
        ::= { vrrpNewCfgVirtRtrTableEntry 17 }

-- VRRP Interface Table

vrrpCurCfgIfTable OBJECT-TYPE
    SYNTAX  SEQUENCE OF VrrpCurCfgIfTableEntry
    ACCESS  not-accessible
    STATUS  mandatory
    DESCRIPTION
        "The table of VRRP interface configuration in current_config."
    ::= { vrrp 4 }
 
vrrpCurCfgIfTableEntry OBJECT-TYPE
    SYNTAX  VrrpCurCfgIfTableEntry
    ACCESS  not-accessible
    STATUS  mandatory
    DESCRIPTION
        "Information about a VRRP interface."
    INDEX   { vrrpCurCfgIfIndx }
    ::= { vrrpCurCfgIfTable 1 }
 
VrrpCurCfgIfTableEntry ::= SEQUENCE {
    vrrpCurCfgIfIndx         INTEGER,
    vrrpCurCfgIfAuthType     INTEGER,
    vrrpCurCfgIfPasswd       DisplayString
    }

vrrpCurCfgIfIndx OBJECT-TYPE
    SYNTAX  INTEGER
    ACCESS  read-only
    STATUS  mandatory
    DESCRIPTION
        "The VRRP interface index.  This is eqivalent to IfIndex."
    ::= { vrrpCurCfgIfTableEntry 1 }

vrrpCurCfgIfAuthType OBJECT-TYPE
    SYNTAX  INTEGER {
        none(1),
        simple-text-password(2)
        }
    ACCESS  read-only
    STATUS  mandatory
    DESCRIPTION
        "Type of authentication being used.
	 none(1) - no authentication
	 simple-text-password(2) - use password specified in 
         vrrpCurCfgIfPasswd for authentication."
    ::= { vrrpCurCfgIfTableEntry 2 }

vrrpCurCfgIfPasswd OBJECT-TYPE
    SYNTAX  DisplayString (SIZE(0..7))
    ACCESS  read-only
    STATUS  mandatory
    DESCRIPTION
        "The password for authentication."
    ::= { vrrpCurCfgIfTableEntry 3 }

vrrpNewCfgIfTable OBJECT-TYPE
    SYNTAX  SEQUENCE OF VrrpNewCfgIfTableEntry
    ACCESS  not-accessible
    STATUS  mandatory
    DESCRIPTION
        "The table of VRRP interface configuration in current_config."
    ::= { vrrp 5 }
 
vrrpNewCfgIfTableEntry OBJECT-TYPE
    SYNTAX  VrrpNewCfgIfTableEntry
    ACCESS  not-accessible
    STATUS  mandatory
    DESCRIPTION
        "Information about a VRRP interface."
    INDEX   { vrrpNewCfgIfIndx }
    ::= { vrrpNewCfgIfTable 1 }
 
VrrpNewCfgIfTableEntry ::= SEQUENCE {
    vrrpNewCfgIfIndx         INTEGER,
    vrrpNewCfgIfAuthType     INTEGER,
    vrrpNewCfgIfPasswd       DisplayString,
    vrrpNewCfgIfDelete       INTEGER
    }

vrrpNewCfgIfIndx OBJECT-TYPE
    SYNTAX  INTEGER
    ACCESS  read-only
    STATUS  mandatory
    DESCRIPTION
        "The VRRP interface index.  This is eqivalent to IfIndex."
    ::= { vrrpNewCfgIfTableEntry 1 }

vrrpNewCfgIfAuthType OBJECT-TYPE
    SYNTAX  INTEGER {
        none(1),
        simple-text-password(2)
        }
    ACCESS  read-write
    STATUS  mandatory
    DESCRIPTION
        "Type of authentication being used.
	 none(1) - no authentication
	 simple-text-password(2) - use password specified in 
         vrrpNewCfgIfPasswd for authentication."
    ::= { vrrpNewCfgIfTableEntry 2 }

vrrpNewCfgIfPasswd OBJECT-TYPE
    SYNTAX  DisplayString (SIZE(0..7))
    ACCESS  read-write
    STATUS  mandatory
    DESCRIPTION
        "The password for authentication."
    ::= { vrrpNewCfgIfTableEntry 3 }

vrrpNewCfgIfDelete OBJECT-TYPE
    SYNTAX  INTEGER {
        other(1),
        delete(2)
        }
    ACCESS  read-write
    STATUS  mandatory
    DESCRIPTION
        "When set to the value of 2 (delete), the entire row is deleted. 
         When read, other(1) is returned. Setting the value to anything 
         other than delete(2) has no effect on the state of the row."
    ::= { vrrpNewCfgIfTableEntry 4 }

-- Failover Virtual Router Groups

vrrpCurCfgVirtRtrGrpTable OBJECT-TYPE
    SYNTAX  SEQUENCE OF VrrpCurCfgVirtRtrGrpTableEntry
    ACCESS  not-accessible
    STATUS  mandatory
    DESCRIPTION
        "The table of VRRP virtual router group in current_config."
    ::= { vrrp 6 }

vrrpCurCfgVirtRtrGrpTableEntry OBJECT-TYPE
    SYNTAX  VrrpCurCfgVirtRtrGrpTableEntry
    ACCESS  not-accessible
    STATUS  mandatory
    DESCRIPTION
        "Information about a VRRP failover virtual router."
    INDEX   { vrrpCurCfgVirtRtrGrpIndx }
    ::= { vrrpCurCfgVirtRtrGrpTable 1 }

VrrpCurCfgVirtRtrGrpTableEntry ::= SEQUENCE {
    vrrpCurCfgVirtRtrGrpIndx         INTEGER,
    vrrpCurCfgVirtRtrGrpID           INTEGER,
    vrrpCurCfgVirtRtrGrpIfIndex      INTEGER,
    vrrpCurCfgVirtRtrGrpInterval     INTEGER,
    vrrpCurCfgVirtRtrGrpPriority     INTEGER,
    vrrpCurCfgVirtRtrGrpPreempt      INTEGER,
    vrrpCurCfgVirtRtrGrpState        INTEGER,
    vrrpCurCfgVirtRtrGrpSharing      INTEGER,
    vrrpCurCfgVirtRtrGrpTckVirtRtr   INTEGER,
    vrrpCurCfgVirtRtrGrpTckIpIntf    INTEGER,
    vrrpCurCfgVirtRtrGrpTckVlanPort  INTEGER,
    vrrpCurCfgVirtRtrGrpTckL4Port    INTEGER,
    vrrpCurCfgVirtRtrGrpTckRServer   INTEGER,
    vrrpCurCfgVirtRtrGrpTckHsrp      INTEGER,
    vrrpCurCfgVirtRtrGrpTckHsrv      INTEGER
    }
 
vrrpCurCfgVirtRtrGrpIndx OBJECT-TYPE
    SYNTAX  INTEGER
    ACCESS  read-only
    STATUS  mandatory
    DESCRIPTION
        "The VRRP virtual router table index."
    ::= { vrrpCurCfgVirtRtrGrpTableEntry 1 }
 
vrrpCurCfgVirtRtrGrpID OBJECT-TYPE
    SYNTAX  INTEGER (1..255)
    ACCESS  read-only
    STATUS  mandatory
    DESCRIPTION
        "The VRRP virtual router identifier."
    ::= { vrrpCurCfgVirtRtrGrpTableEntry 2 }
 
vrrpCurCfgVirtRtrGrpIfIndex OBJECT-TYPE
    SYNTAX  INTEGER
    ACCESS  read-only
    STATUS  mandatory
    DESCRIPTION
        "The IfIndex that the VRRP virtual router is representing."
    ::= { vrrpCurCfgVirtRtrGrpTableEntry 3 }

vrrpCurCfgVirtRtrGrpInterval OBJECT-TYPE
    SYNTAX  INTEGER (1..255)
    ACCESS  read-only
    STATUS  mandatory
    DESCRIPTION
        "The time interval between VRRP advertisements in seconds."
    ::= { vrrpCurCfgVirtRtrGrpTableEntry 4 }

vrrpCurCfgVirtRtrGrpPriority OBJECT-TYPE
    SYNTAX  INTEGER (1..254)
    ACCESS  read-only
    STATUS  mandatory
    DESCRIPTION
        "The priority value to be used by the specified VRRP virtual routers."
    ::= { vrrpCurCfgVirtRtrGrpTableEntry 5 }

vrrpCurCfgVirtRtrGrpPreempt OBJECT-TYPE
    SYNTAX  INTEGER {
        enabled(1),
        disabled(2)
        }
    ACCESS  read-only
    STATUS  mandatory
    DESCRIPTION
        "This is for controlling whether a higher priority Backup
         VRRP virtual router preempts a low priority Master.

         enabled(1)  - allow preemption
         disabled(2) - prohibit preemption"
   ::= { vrrpCurCfgVirtRtrGrpTableEntry 6 }

vrrpCurCfgVirtRtrGrpState OBJECT-TYPE
    SYNTAX  INTEGER {
        enabled(1),
        disabled(2)
        }
    ACCESS  read-only
    STATUS  mandatory
    DESCRIPTION
        "Enable or disable the VRRP virtual router."
    ::= { vrrpCurCfgVirtRtrGrpTableEntry 7 }

vrrpCurCfgVirtRtrGrpSharing OBJECT-TYPE
    SYNTAX  INTEGER {
        enabled(1),
        disabled(2)
        }
    ACCESS  read-only
    STATUS  mandatory
    DESCRIPTION
        "Enable or disable load sharing of non-master virtual router."
    ::= { vrrpCurCfgVirtRtrGrpTableEntry 8 }

vrrpCurCfgVirtRtrGrpTckVirtRtr OBJECT-TYPE
    SYNTAX  INTEGER {
        enabled(1),
        disabled(2)
        }
    ACCESS  read-only
    STATUS  mandatory
    DESCRIPTION
        "Enable or disable tracking other virtual routers for
         priority adjustment.  the priority increment is defined
         in vrrpCurCfgGenTckVirtRtrInc."
    ::= { vrrpCurCfgVirtRtrGrpTableEntry 9 }

vrrpCurCfgVirtRtrGrpTckIpIntf OBJECT-TYPE
    SYNTAX  INTEGER {
        enabled(1),
        disabled(2)
        }
    ACCESS  read-only
    STATUS  mandatory
    DESCRIPTION
        "Enable or disable tracking other router interfaces for
         priority adjustment.  the priority increment is defined
         in vrrpCurCfgGenTckIpIntfInc."
    ::= { vrrpCurCfgVirtRtrGrpTableEntry 10 }

vrrpCurCfgVirtRtrGrpTckVlanPort OBJECT-TYPE
    SYNTAX  INTEGER {
        enabled(1),
        disabled(2)
        }
    ACCESS  read-only
    STATUS  mandatory
    DESCRIPTION
        "Enable or disable tracking port state of VLAN ports
         for priority adjustment.  the priority increment is
         defined in vrrpCurCfgGenTckVlanPortInc."
    ::= { vrrpCurCfgVirtRtrGrpTableEntry 11 }

vrrpCurCfgVirtRtrGrpTckL4Port OBJECT-TYPE
    SYNTAX  INTEGER {
        enabled(1),
        disabled(2)
        }
    ACCESS  read-only
    STATUS  mandatory
    DESCRIPTION
        "Enable or disable tracking Layer 4 port states for
         priority adjustment.  the priority increment is defined
         in vrrpCurCfgGenTckL4PortInc.  This is applied when
         virtual server is configured as a VRRP virtual router."
    ::= { vrrpCurCfgVirtRtrGrpTableEntry 12 }

vrrpCurCfgVirtRtrGrpTckRServer OBJECT-TYPE
    SYNTAX  INTEGER {
        enabled(1),
        disabled(2)
        }
    ACCESS  read-only
    STATUS  mandatory
    DESCRIPTION
        "Enable or disable tracking real server states for
         priority adjustment.  the priority increment is defined
         in vrrpCurCfgGenTckRServerInc.  This is applied when
         virtual server is configured as a VRRP virtual router."
    ::= { vrrpCurCfgVirtRtrGrpTableEntry 13 }

vrrpCurCfgVirtRtrGrpTckHsrp OBJECT-TYPE
    SYNTAX  INTEGER {
        enabled(1),
        disabled(2)
        }
    ACCESS  read-only
    STATUS  mandatory
    DESCRIPTION
        "Enable or disable tracking HSRP advertisements for
         priority adjustment.  the priority increment is defined
         in vrrpCurCfgGenTckHsrpInc.  This is applied when
         virtual server is configured as a VRRP virtual router."
    ::= { vrrpCurCfgVirtRtrGrpTableEntry 14 }

vrrpCurCfgVirtRtrGrpTckHsrv OBJECT-TYPE
        SYNTAX  INTEGER {
                enabled(1),
                disabled(2)
                }
        ACCESS  read-only
        STATUS  mandatory
        DESCRIPTION
                "Enable or disable tracking HSRP by VLAN advertisements for
                 priority adjustment.  The priority increment is defined
                 in vrrpCurCfgGenTckHsrvInc.  This is applied when
                 virtual server is configured as a VRRP virtual router."
        ::= { vrrpCurCfgVirtRtrGrpTableEntry 15 }

vrrpNewCfgVirtRtrGrpTable OBJECT-TYPE
    SYNTAX  SEQUENCE OF VrrpNewCfgVirtRtrGrpTableEntry
    ACCESS  not-accessible
    STATUS  mandatory
    DESCRIPTION
        "The table of VRRP virtual router group configuration in new_config."
    ::= { vrrp 7 }

vrrpNewCfgVirtRtrGrpTableEntry OBJECT-TYPE
    SYNTAX  VrrpNewCfgVirtRtrGrpTableEntry
    ACCESS  not-accessible
    STATUS  mandatory
    DESCRIPTION
        "Information about a VRRP failover virtual router."
    INDEX   { vrrpNewCfgVirtRtrGrpIndx }
    ::= { vrrpNewCfgVirtRtrGrpTable 1 }
 
VrrpNewCfgVirtRtrGrpTableEntry ::= SEQUENCE {
    vrrpNewCfgVirtRtrGrpIndx         INTEGER,
    vrrpNewCfgVirtRtrGrpID           INTEGER,
    vrrpNewCfgVirtRtrGrpIfIndex      INTEGER,
    vrrpNewCfgVirtRtrGrpInterval     INTEGER,
    vrrpNewCfgVirtRtrGrpPriority     INTEGER,
    vrrpNewCfgVirtRtrGrpPreempt      INTEGER,
    vrrpNewCfgVirtRtrGrpState        INTEGER,
    vrrpNewCfgVirtRtrGrpDelete       INTEGER,
    vrrpNewCfgVirtRtrGrpSharing      INTEGER,
    vrrpNewCfgVirtRtrGrpTckVirtRtr   INTEGER,
    vrrpNewCfgVirtRtrGrpTckIpIntf    INTEGER,
    vrrpNewCfgVirtRtrGrpTckVlanPort  INTEGER,
    vrrpNewCfgVirtRtrGrpTckL4Port    INTEGER,
    vrrpNewCfgVirtRtrGrpTckRServer   INTEGER,
    vrrpNewCfgVirtRtrGrpTckHsrp      INTEGER,
    vrrpNewCfgVirtRtrGrpTckHsrv      INTEGER
    }
 
vrrpNewCfgVirtRtrGrpIndx OBJECT-TYPE
    SYNTAX  INTEGER
    ACCESS  read-only
    STATUS  mandatory
    DESCRIPTION
        "The VRRP virtual router table index."
    ::= { vrrpNewCfgVirtRtrGrpTableEntry 1 }
 
vrrpNewCfgVirtRtrGrpID OBJECT-TYPE
    SYNTAX  INTEGER (1..255)
    ACCESS  read-write
    STATUS  mandatory
    DESCRIPTION
        "The VRRP virtual router identifier."
    ::= { vrrpNewCfgVirtRtrGrpTableEntry 2 }
 
vrrpNewCfgVirtRtrGrpIfIndex OBJECT-TYPE
    SYNTAX  INTEGER
    ACCESS  read-write
    STATUS  mandatory
    DESCRIPTION
        "The IfIndex that the VRRP virtual router is representing."
    ::= { vrrpNewCfgVirtRtrGrpTableEntry 3 }

vrrpNewCfgVirtRtrGrpInterval OBJECT-TYPE
    SYNTAX  INTEGER (1..255)
    ACCESS  read-write
    STATUS  mandatory
    DESCRIPTION
        "The time interval between VRRP advertisements in seconds."
    ::= { vrrpNewCfgVirtRtrGrpTableEntry 4 }

vrrpNewCfgVirtRtrGrpPriority OBJECT-TYPE
    SYNTAX  INTEGER (1..254)
    ACCESS  read-write
    STATUS  mandatory
    DESCRIPTION
        "The priority value to be used by the specified VRRP virtual router."
    ::= { vrrpNewCfgVirtRtrGrpTableEntry 5 }

vrrpNewCfgVirtRtrGrpPreempt OBJECT-TYPE
    SYNTAX  INTEGER {
        enabled(1),
        disabled(2)
        }
    ACCESS  read-write
    STATUS  mandatory
    DESCRIPTION
        "This is for controlling whether a higher priority Backup
         VRRP virtual router preempts a low priority Master.

         enabled(1)  - allow preemption
         disabled(2) - prohibit preemption"
    ::= { vrrpNewCfgVirtRtrGrpTableEntry 6 }

vrrpNewCfgVirtRtrGrpState OBJECT-TYPE
    SYNTAX  INTEGER {
        enabled(1),
        disabled(2)
        }
    ACCESS  read-write
    STATUS  mandatory
    DESCRIPTION
        "Enable or disable the VRRP virtual router."
    ::= { vrrpNewCfgVirtRtrGrpTableEntry 7 }

vrrpNewCfgVirtRtrGrpDelete OBJECT-TYPE
    SYNTAX  INTEGER {
        other(1),
        delete(2)
        }
    ACCESS  read-write
    STATUS  mandatory
    DESCRIPTION
        "When set to the value of 2 (delete), the entire row is deleted. 
         When read, other(1) is returned. Setting the value to anything 
         other than delete(2) has no effect on the state of the row."
    ::= { vrrpNewCfgVirtRtrGrpTableEntry 8 }

vrrpNewCfgVirtRtrGrpSharing OBJECT-TYPE
    SYNTAX  INTEGER {
        enabled(1),
        disabled(2)
        }
    ACCESS  read-write
    STATUS  mandatory
    DESCRIPTION
        "Enable or disable load sharing of non-master virtual router."
    ::= { vrrpNewCfgVirtRtrGrpTableEntry 9 }

vrrpNewCfgVirtRtrGrpTckVirtRtr OBJECT-TYPE
    SYNTAX  INTEGER {
        enabled(1),
        disabled(2)
        }
    ACCESS  read-write
    STATUS  mandatory
    DESCRIPTION
        "Enable or disable tracking other virtual routers for
         priority adjustment.  the priority increment is defined
         in vrrpNewCfgGenTckVirtRtrInc."
    ::= { vrrpNewCfgVirtRtrGrpTableEntry 10 }

vrrpNewCfgVirtRtrGrpTckIpIntf OBJECT-TYPE
    SYNTAX  INTEGER {
        enabled(1),
        disabled(2)
        }
    ACCESS  read-write
    STATUS  mandatory
    DESCRIPTION
        "Enable or disable tracking other router interfaces for
         priority adjustment.  the priority increment is defined
         in vrrpNewCfgGenTckIpIntfInc."
    ::= { vrrpNewCfgVirtRtrGrpTableEntry 11 }

vrrpNewCfgVirtRtrGrpTckVlanPort OBJECT-TYPE
    SYNTAX  INTEGER {
        enabled(1),
        disabled(2)
        }
    ACCESS  read-write
    STATUS  mandatory
    DESCRIPTION
        "Enable or disable tracking port state of VLAN ports
         for priority adjustment.  the priority increment is
         defined in vrrpNewCfgGenTckVlanPortInc."
    ::= { vrrpNewCfgVirtRtrGrpTableEntry 12 }

vrrpNewCfgVirtRtrGrpTckL4Port OBJECT-TYPE
    SYNTAX  INTEGER {
        enabled(1),
        disabled(2)
        }
    ACCESS  read-write
    STATUS  mandatory
    DESCRIPTION
        "Enable or disable tracking Layer 4 port states for
         priority adjustment.  the priority increment is defined
         in vrrpNewCfgGenTckL4PortInc.  This is applied when
         virtual server is configured as a VRRP virtual router."
    ::= { vrrpNewCfgVirtRtrGrpTableEntry 13 }

vrrpNewCfgVirtRtrGrpTckRServer OBJECT-TYPE
    SYNTAX  INTEGER {
        enabled(1),
        disabled(2)
        }
    ACCESS  read-write
    STATUS  mandatory
    DESCRIPTION
        "Enable or disable tracking real server states for
         priority adjustment.  the priority increment is defined
         in vrrpNewCfgGenTckRServerInc.  This is applied when
         virtual server is configured as a VRRP virtual router."
    ::= { vrrpNewCfgVirtRtrGrpTableEntry 14 }

vrrpNewCfgVirtRtrGrpTckHsrp OBJECT-TYPE
    SYNTAX  INTEGER {
        enabled(1),
        disabled(2)
        }
    ACCESS  read-write
    STATUS  mandatory
    DESCRIPTION
        "Enable or disable tracking HSRP advertisements for
         priority adjustment.  the priority increment is defined
         in vrrpNewCfgGenTckHsrpInc.  This is applied when
         virtual server is configured as a VRRP virtual router."
    ::= { vrrpNewCfgVirtRtrGrpTableEntry 15 }

vrrpNewCfgVirtRtrGrpTckHsrv OBJECT-TYPE
        SYNTAX  INTEGER {
                enabled(1),
                disabled(2)
                }
        ACCESS  read-write
        STATUS  mandatory
        DESCRIPTION
                "Enable or disable tracking HSRP by VLAN advertisements for
                 priority adjustment.  The priority increment is defined
                 in vrrpNewCfgGenTckHsrvInc.  This is applied when
                 virtual server is configured as a VRRP virtual router."
        ::= { vrrpNewCfgVirtRtrGrpTableEntry 16 }

vrrpVirtRtrTableMaxSize OBJECT-TYPE
    SYNTAX INTEGER
    ACCESS read-only
    STATUS mandatory
    DESCRIPTION
        "The maximum number of entries in VRRP virtual router table."
    ::= { vrrp 8 }

vrrpIfTableMaxSize OBJECT-TYPE
    SYNTAX INTEGER
    ACCESS read-only
    STATUS mandatory
    DESCRIPTION
        "The maximum number of entries in VRRP interface table."
    ::= { vrrp 9 }

vrrpVirtRtrGrpTableMaxSize OBJECT-TYPE
    SYNTAX INTEGER
    ACCESS read-only
    STATUS mandatory
    DESCRIPTION
        "The maximum number of entries in VRRP Group table."
    ::= { vrrp 10 }

-- Statistics

-- RIP Statistics Group

ripStatInPkts OBJECT-TYPE
    SYNTAX  Counter
    ACCESS  read-only
    STATUS  mandatory
    DESCRIPTION
        "The total number of good RIP packets recieved."
    ::= { ripStats 1 }

ripStatOutPkts OBJECT-TYPE
    SYNTAX  Counter
    ACCESS  read-only
    STATUS  mandatory
    DESCRIPTION
        "The total number of RIP packets transmitted."
    ::= { ripStats 2 }

ripStatInErrorPkts OBJECT-TYPE
    SYNTAX  Counter
    ACCESS  read-only
    STATUS  mandatory
    DESCRIPTION
        "The total number of error RIP packets recieved."
    ::= { ripStats 3 }

ripStatRoutesAgedOut OBJECT-TYPE
    SYNTAX  Counter
    ACCESS  read-only
    STATUS  mandatory
    DESCRIPTION
        "The total number of RIP routes which have aged out."
    ::= { ripStats 4 }

-- ARP Statistics Group

arpStatEntries OBJECT-TYPE
    SYNTAX  Gauge 
    ACCESS  read-only
    STATUS  mandatory
    DESCRIPTION
        "The current number of ARP entries."
    ::= { arpStats 1 }

arpStatHighWater OBJECT-TYPE
    SYNTAX  Gauge 
    ACCESS  read-only
    STATUS  mandatory
    DESCRIPTION
        "The highest number of ARP entries."
    ::= { arpStats 2 }

arpStatMaxEntries OBJECT-TYPE
    SYNTAX  Gauge 
    ACCESS  read-only
    STATUS  mandatory
    DESCRIPTION
        "The maximum number of ARP entries."
    ::= { arpStats 3 }

-- ROUTE Statistics Group

routeStatEntries OBJECT-TYPE
    SYNTAX  Gauge 
    ACCESS  read-only
    STATUS  mandatory
    DESCRIPTION
        "The current number of IP routes."
    ::= { routeStats 1 }

routeStatHighWater OBJECT-TYPE
    SYNTAX  Gauge 
    ACCESS  read-only
    STATUS  mandatory
    DESCRIPTION
        "The highest number of IP routes."
    ::= { routeStats 2 }

routeStatMaxEntries OBJECT-TYPE
    SYNTAX  Gauge 
    ACCESS  read-only
    STATUS  mandatory
    DESCRIPTION
        "The maximum number of IP routes."
    ::= { routeStats 3 }

-- DNS Statistics

dnsStatInGoodDnsRequests OBJECT-TYPE 
    SYNTAX  Counter 
    ACCESS  read-only
    STATUS  mandatory 
    DESCRIPTION 
        "The number of good DNS requests which are received."
    ::= { dnsStats 1 }

dnsStatInBadDnsRequests OBJECT-TYPE 
    SYNTAX  Counter 
    ACCESS  read-only
    STATUS  mandatory 
    DESCRIPTION 
        "The number of bad DNS requests which are received."
    ::= { dnsStats 2 }

-- The VRRP Statistics

vrrpStatInAdvers OBJECT-TYPE 
    SYNTAX  Counter 
    ACCESS  read-only
    STATUS  mandatory 
    DESCRIPTION 
        "The number of good VRRP advertisements which are received."
    ::= { vrrpStats 1 }

vrrpStatOutAdvers OBJECT-TYPE 
    SYNTAX  Counter 
    ACCESS  read-only
    STATUS  mandatory 
    DESCRIPTION 
        "The number of good VRRP advertisements which are transmitted."
    ::= { vrrpStats 2 }

vrrpStatOutBadAdvers OBJECT-TYPE 
    SYNTAX  Counter 
    ACCESS  read-only
    STATUS  mandatory 
    DESCRIPTION 
        "The number of bad VRRP advertisements which are received."
    ::= { vrrpStats 3 }

-- Information - Run-time IP Route Table 

ipRouteInfoTable OBJECT-TYPE
    SYNTAX  SEQUENCE OF IpRouteInfoEntry
    ACCESS  not-accessible
    STATUS  mandatory
    DESCRIPTION
        "The table of run-time IP routes."
    ::= { ip-info 1 }

ipRouteInfoEntry OBJECT-TYPE
    SYNTAX  IpRouteInfoEntry
    ACCESS  not-accessible
    STATUS  mandatory
    DESCRIPTION
        "A row in the run-time IP route table"
    INDEX   { ipRouteInfoIndx }
    ::= { ipRouteInfoTable 1 }

IpRouteInfoEntry ::= SEQUENCE {
    ipRouteInfoIndx	        INTEGER,
    ipRouteInfoDestIp           IpAddress,
    ipRouteInfoMask             IpAddress,
    ipRouteInfoGateway          IpAddress,
    ipRouteInfoTag       	INTEGER,
    ipRouteInfoType       	INTEGER,
    ipRouteInfoInterface        INTEGER
    }

ipRouteInfoIndx OBJECT-TYPE
    SYNTAX  INTEGER
    ACCESS  read-only
    STATUS  mandatory
    DESCRIPTION
        "The index of this route table."
    ::= { ipRouteInfoEntry 1 }

ipRouteInfoDestIp OBJECT-TYPE
    SYNTAX  IpAddress
    ACCESS  read-only
    STATUS  mandatory
    DESCRIPTION
        "The destination IP address of this route."
    ::= { ipRouteInfoEntry 2 }

ipRouteInfoMask OBJECT-TYPE
    SYNTAX  IpAddress
    ACCESS  read-only
    STATUS  mandatory
    DESCRIPTION
        "The destination IP mask of this route."
    ::= { ipRouteInfoEntry 3 }
 
ipRouteInfoGateway OBJECT-TYPE
    SYNTAX  IpAddress
    ACCESS  read-only
    STATUS  mandatory
    DESCRIPTION
        "The next-hop router address for this route."
    ::= { ipRouteInfoEntry 4 }

ipRouteInfoTag OBJECT-TYPE
    SYNTAX  INTEGER {
	fixed(1),
  	icmp(2),
  	static(3),
	snmp(4),
	addr(5),
	rip(6),
	broadcast(7),
	martian(8),
	multicast(9),
        vip(10),
        bgp(11),
        none(12)
	}
    ACCESS  read-only
    STATUS  mandatory
    DESCRIPTION
        "The tag-type for this route."
    ::= { ipRouteInfoEntry 5 }

ipRouteInfoType OBJECT-TYPE 
    SYNTAX  INTEGER {
	indirect(1),
	direct(2),
	local(3),
	broadcast(4),
	martian(5),
	multicast(6),
	other(7)
	}
    ACCESS  read-only 
    STATUS  mandatory 
    DESCRIPTION 
        "The type of the route." 
    ::= { ipRouteInfoEntry 6 }

ipRouteInfoInterface OBJECT-TYPE 
    SYNTAX  INTEGER
    ACCESS  read-only 
    STATUS  mandatory 
    DESCRIPTION 
        "The interface number for which the destination	address is applicable."
    ::= { ipRouteInfoEntry 7 }

-- Run Time ARP Table

arpInfoTable OBJECT-TYPE
    SYNTAX  SEQUENCE OF AgArpInfoEntry
    ACCESS  not-accessible
    STATUS  mandatory
    DESCRIPTION
        "The table of ARP entries."
    ::= { ip-info 2 }

arpInfoEntry OBJECT-TYPE
    SYNTAX  AgArpInfoEntry
    ACCESS  not-accessible
    STATUS  mandatory
    DESCRIPTION
        "A row in the ARP table"
    INDEX   { arpInfoDestIp }
    ::= { arpInfoTable 1 }

AgArpInfoEntry ::= SEQUENCE {
    arpInfoDestIp         IpAddress,
    arpInfoMacAddr        PhysAddress,
    arpInfoVLAN        	  INTEGER,
    arpInfoSrcPort        INTEGER,
    arpInfoRefPorts       INTEGER,
    arpInfoFlag           INTEGER
    }

arpInfoDestIp OBJECT-TYPE
    SYNTAX  IpAddress
    ACCESS  read-only
    STATUS  mandatory
    DESCRIPTION
        "The destination IP address of the ARP entry."
    ::= { arpInfoEntry 1 }

arpInfoMacAddr OBJECT-TYPE
    SYNTAX  PhysAddress
    ACCESS  read-only
    STATUS  mandatory
    DESCRIPTION
        "The MAC address for the ARP entry."
    ::= { arpInfoEntry 2 }

arpInfoVLAN OBJECT-TYPE 
    SYNTAX  INTEGER 
    ACCESS  read-only 
    STATUS  mandatory 
    DESCRIPTION 
        "The VLAN identifier for the ARP entry." 
    ::= { arpInfoEntry 3 }

arpInfoSrcPort OBJECT-TYPE  
    SYNTAX  INTEGER 
    ACCESS  read-only  
    STATUS  mandatory  
    DESCRIPTION  
        "The  port number on which this entry's equivalence is effective."  
    ::= { arpInfoEntry 4 }

arpInfoRefPorts OBJECT-TYPE   
    SYNTAX  INTEGER  
    ACCESS  read-only   
    STATUS  mandatory   
    DESCRIPTION   
        "The rference ports associated with this ARP entry."   
    ::= { arpInfoEntry 5 }

arpInfoFlag OBJECT-TYPE   
    SYNTAX  INTEGER {
	clear(1),
	unresolved(2),
	permanent(3),
	indirect(4)
	}
    ACCESS  read-only   
    STATUS  mandatory   
    DESCRIPTION   
        "The flag associated with this ARP entry."   
    ::= { arpInfoEntry 6 }

-- VRRP Information

vrrpInfoVirtRtrTable OBJECT-TYPE
    SYNTAX  SEQUENCE OF VrrpInfoVirtRtrTableEntry
    ACCESS  not-accessible
    STATUS  mandatory
    DESCRIPTION
        "The table of VRRP virtual router run-time information."
    ::= { vrrp-info 1 }

vrrpInfoVirtRtrTableEntry OBJECT-TYPE
    SYNTAX  VrrpInfoVirtRtrTableEntry
    ACCESS  not-accessible
    STATUS  mandatory
    DESCRIPTION
        "The run-time information about a VRRP virtual router."
    INDEX   { vrrpInfoVirtRtrIndex }
    ::= { vrrpInfoVirtRtrTable 1 }
 
VrrpInfoVirtRtrTableEntry ::= SEQUENCE {
    vrrpInfoVirtRtrIndex      INTEGER,
    vrrpInfoVirtRtrState      INTEGER
    }

vrrpInfoVirtRtrIndex OBJECT-TYPE
    SYNTAX  INTEGER
    ACCESS  read-only
    STATUS  mandatory
    DESCRIPTION
        "The VRRP virtual router index." 
    ::= { vrrpInfoVirtRtrTableEntry 1 }

vrrpInfoVirtRtrState OBJECT-TYPE   
    SYNTAX  INTEGER {
	init(1),
	master(2),
	backup(3)
	}
    ACCESS  read-only   
    STATUS  mandatory   
    DESCRIPTION   
        "The VRRP virtual router state."   
    ::= { vrrpInfoVirtRtrTableEntry 2 }

END