-- MIB created 6/25/99 12:57:35, by
--   SMIC (the next generation) version 1.6.29, November 22, 1994.

CISCO-SIBU-FLASH-MIB DEFINITIONS ::= BEGIN

-- From file: "CISCO-SIBU-FLASH-MIB.my"

IMPORTS
    Integer32, IpAddress
            FROM SNMPv2-SMI-v1
    OBJECT-TYPE
            FROM RFC-1212
    DisplayString
            FROM SNMPv2-TC-v1
    ciscoExperiment
            FROM CISCO-SMI;

ciscoSibuFlashMIB OBJECT IDENTIFIER ::= { ciscoExperiment 45 }
-- MODULE-IDENTITY
--  LastUpdated
--    9810230000Z
--  OrgName
--    Cisco Systems Inc.
--  ContactInfo
--    Cisco Systems
--     Customer Service
--    
--     Postal: 170 W Tasman Drive
--     San Jose, CA  95134
--     USA
--    
--     Tel: +1 800 553-NETS
--     E-mail: cs-sibu@cisco.com
--  Descr
--    The MIB module that provides a simple mechanism
--     to support firmware upgrade on Cisco low end
--     devices.
--  RevDate
--    9810230000Z
--  RevDescr
--    Initial version of this MIB module.

ciscoSibuFlashMIBObjects OBJECT IDENTIFIER ::= { ciscoSibuFlashMIB 1 }
csfUpgrade      OBJECT IDENTIFIER ::= { ciscoSibuFlashMIBObjects 1 }
ciscoSibuFlashMIBNotificationsPrefix OBJECT IDENTIFIER ::= { ciscoSibuFlashMIB 2 }
ciscoSibuFlashMIBNotifications OBJECT IDENTIFIER ::= { ciscoSibuFlashMIBNotificationsPrefix 0 }
ciscoSibuFlashMIBComformance OBJECT IDENTIFIER ::= { ciscoSibuFlashMIB 3 }
ciscoSibuFlashMIBCompliances OBJECT IDENTIFIER ::= { ciscoSibuFlashMIBComformance 1 }
ciscoSibuFlashMIBGroups OBJECT IDENTIFIER ::= { ciscoSibuFlashMIBComformance 2 }

csfUpgradeFirmwareVersion OBJECT-TYPE
    SYNTAX DisplayString(SIZE(0..8))
--    Rsyntax OCTET STRING(SIZE(0..8))
    ACCESS read-only
    STATUS mandatory
    DESCRIPTION
        "Returns the version number of the device system
         firmware residing in flash. The string has a
         'V1.2.3' format."
    ::= { csfUpgrade 1 }

csfUpgradeFlashSize OBJECT-TYPE
    SYNTAX Integer32(0..2147483647)
--  Units
--    kbytes
    ACCESS read-only
    STATUS mandatory
    DESCRIPTION
        "The size of available FLASH memory in the system,
        in kilobytes.  For example: 128 equals 131072 bytes
        (128 bytes times 1024)."
    ::= { csfUpgrade 2 }

csfUpgradeTFTPServerAddress OBJECT-TYPE
    SYNTAX IpAddress
    ACCESS read-write
    STATUS mandatory
    DESCRIPTION
        "The IP address of a TFTP server from which a firmware
         image can be downloaded.  The download may be initiated
         by setting the upgradeTFTPInitiate to upgrade(1), or via
         an out-of-band management action."
--    DEFVAL { 0.0.0.0 }
    ::= { csfUpgrade 3 }

csfUpgradeTFTPLoadFilename OBJECT-TYPE
    SYNTAX DisplayString(SIZE(0..80))
--    Rsyntax OCTET STRING(SIZE(0..80))
    ACCESS read-write
    STATUS mandatory
    DESCRIPTION
        "The name of the file containing a firmware upgrade
         image on the host whose address is given by
         upgradeTFTPServerAddress.  The default value is
         an empty string, or no filename."
    DEFVAL { "" }
    ::= { csfUpgrade 4 }

csfUpgradeTFTPInitiate OBJECT-TYPE
    SYNTAX INTEGER {
        upgrade(1),
        noUpgrade(2)
        }
    ACCESS read-write
    STATUS mandatory
    DESCRIPTION
        "Setting this object to noUpgrade(2) results in no
         action. When set to upgrade(1), the switch will attempt
         to download a firmware upgrade image from the server
         whose address is given by upgradeTFTPServerAddress.
         The image is found in the file whose name is given by
         sibuFlashTFTPLoadFilename.  Both
         sibuFlashTFTPServerAddress and
         sibuFlashTFTPLoadFilename must be non-empty for the
         upgrade to proceed.
        
         This object always returns noUpgrade(2) when read."
    DEFVAL { noUpgrade }
    ::= { csfUpgrade 5 }

csfUpgradeFlashMode OBJECT-TYPE
    SYNTAX INTEGER {
        permanent(1),
        temporary(2)
        }
    ACCESS read-write
    STATUS mandatory
    DESCRIPTION
        "Indicates whether a newly upgraded firmware version
         should write to flash.  When this object is temporary(2),
         following a successful upgrade the system will switch to
         run the new firmware but will not upgrade the new
         firmware to flash.  That means after a power cycle,
         system will run the firmware residing the flash.
        
         When this object is permanent(1), following a successful
         firmware upgrade, the flash will be upgraded and the
         system will automatically switch to run the new firmware."
    DEFVAL { permanent }
    ::= { csfUpgrade 6 }

csfUpgradeFirmwareStatus OBJECT-TYPE
    SYNTAX INTEGER {
        none(1),
        inProgress(2),
        succeeded(3),
        failed(4)
        }
    ACCESS read-only
    STATUS mandatory
    DESCRIPTION
        "Status of last upgrade attempt via TFTP:
         none - no upgrade has ever been attempted since
                initialization.
         inProgress - an upgrade is in progress.
         succeeded - the previous attempt succeeded.
         failed - the previous attempt failed. "
    DEFVAL { none }
    ::= { csfUpgrade 7 }

ciscoSibuFlashMIBGroup OBJECT IDENTIFIER ::= { ciscoSibuFlashMIBGroups 1 }
-- OBJECT-GROUP
--  Status
--    mandatory
--  Descr
--    A collection of image upgrade objects for use with
--     the devices that supports simple upgrade mechanism.
--  objects
--    csfUpgradeFirmwareVersion, csfUpgradeFlashSize, 
--    csfUpgradeTFTPServerAddress, csfUpgradeTFTPLoadFilename, 
--    csfUpgradeTFTPInitiate, csfUpgradeFlashMode, 
--    csfUpgradeFirmwareStatus

ciscoSibuFlashCompliance OBJECT IDENTIFIER ::= { ciscoSibuFlashMIBCompliances 1 }
-- MODULE-COMPLIANCE
--  Status
--    mandatory
--  Descr
--    The compliance statement for the Cisco SIBU Flash MIB.
--  Module
--    >>current<<
--   MandGroup
--    ciscoSibuFlashMIBGroup


END