BFD-STD-MIB DEFINITIONS ::= BEGIN
   IMPORTS
      MODULE-IDENTITY, OBJECT-TYPE,
      Unsigned32, Counter32, Counter64,
      NOTIFICATION-TYPE
         FROM SNMPv2-SMI                        -- [RFC2578]

      MODULE-COMPLIANCE, OBJECT-GROUP,
      NOTIFICATION-GROUP
          FROM SNMPv2-CONF                      -- [RFC2580]

      TEXTUAL-CONVENTION, TruthValue,
      RowStatus, StorageType, TimeStamp
         FROM SNMPv2-TC                         -- [RFC2579]

      InetAddress, InetAddressType, InetPortNumber
         FROM INET-ADDRESS-MIB                  -- [RFC3291]

      -- Juniper specific                                       *** JNX ***
      jnxBfdExperiment                                       -- *** JNX ***
         FROM JUNIPER-EXPERIMENT-MIB                         -- *** JNX ***
   ;

   bfdMIB MODULE-IDENTITY
      LAST-UPDATED "200507221200Z"  -- 04 July 2005 12:00:00 EST
      ORGANIZATION "IETF"
      CONTACT-INFO
          "        Thomas D. Nadeau
                   Cisco Systems, Inc.
           Email:  tnadeau@cisco.com

                   Zafar Ali
                   Cisco Systems, Inc.
           Email:  zali@cisco.com
          "
      DESCRIPTION
          "Bidirectional Forwarding Management Information Base."

      -- Revision history.
      REVISION
          "200508221200Z"  -- 04 August 2005 12:00:00 EST
      DESCRIPTION
      "Initial version. Published as RFC xxxx." -- RFC-editor pls fill
                                                -- in xxxx
   ::= { jnxBfdExperiment 1 }

   -- Top level components of this MIB module.

   bfdNotifications OBJECT IDENTIFIER ::= { bfdMIB 0 }

   bfdObjects       OBJECT IDENTIFIER ::= { bfdMIB 1 }

   bfdConformance   OBJECT IDENTIFIER ::= { bfdMIB 3 }

   bfdScalarObjects OBJECT IDENTIFIER ::= { bfdObjects 1 }


   --  Textual Conventions

   BfdSessIndexTC ::= TEXTUAL-CONVENTION
      DISPLAY-HINT "d"
      STATUS        current
      DESCRIPTION
          "An index used to uniquely identify BFD sessions."
      SYNTAX Unsigned32 (1..4294967295)

   BfdInterval ::= TEXTUAL-CONVENTION
      STATUS        current
      DESCRIPTION
          "The BFD interval delay in microseconds."
      SYNTAX        Unsigned32 (1..4294967295)

   BfdDiag ::=      TEXTUAL-CONVENTION
      STATUS        current
      DESCRIPTION
          "A common BFD diagnostic code."

      SYNTAX INTEGER { noDiagnostic(1),
                       controlDetectionTimeExpired(2),
                       echoFunctionFailed(3),
                       neighborSignaledSessionDown(4),
                       forwardingPlaneReset(5),
                       pathDown(6),
                       concatenatedPathDown(7),
                       administrativelyDown(8),
                       reverseConcatenatedPathDown (9)
                     }

        --  BFD General Variables

        --  These parameters apply globally to the Router's
        --  BFD Process.

   bfdAdminStatus OBJECT-TYPE
      SYNTAX   INTEGER { enabled(1), disabled(2) }
--      MAX-ACCESS   read-write
      MAX-ACCESS   read-only
      STATUS   current
      DESCRIPTION
              "The global administrative status of BFD in this router.
               The value 'enabled' denotes that the BFD Process is
               active on at least one interface; 'disabled' disables
               it on all interfaces."
      DEFVAL { enabled }
      ::= { bfdScalarObjects 1 }

   bfdVersionNumber OBJECT-TYPE
      SYNTAX   Unsigned32
      MAX-ACCESS   read-only
      STATUS   current
      DESCRIPTION
              "The current version number of the BFD protocol."
      REFERENCE
              " BFD Version 0 (draft-katz-ward-bfd-02.txt)"
      DEFVAL { 0 }
      ::= { bfdScalarObjects 3 }


   --  BFD Session Table
   --  The BFD Session Table specifies BFD session specific
   --  information.

   bfdSessTable OBJECT-TYPE
      SYNTAX   SEQUENCE OF BfdSessEntry
      MAX-ACCESS   not-accessible
      STATUS   current
      DESCRIPTION
              "The BFD Session Table describes the BFD sessions."
      REFERENCE
              "BFD Version 0 (draft-katz-ward-bfd-02.txt)"
      ::= { bfdObjects 2 }

   bfdSessEntry OBJECT-TYPE
      SYNTAX      BfdSessEntry
      MAX-ACCESS  not-accessible
      STATUS      current
      DESCRIPTION
              "The BFD Session Entry describes BFD session."
      INDEX { bfdSessIndex }
      ::= { bfdSessTable 1 }

   BfdSessEntry ::= SEQUENCE {
      bfdSessIndex                    BfdSessIndexTC,
      bfdSessApplicationId            Unsigned32,
      bfdSessDiscriminator            Unsigned32,
      bfdSessRemoteDiscr              Unsigned32,
      bfdSessUdpPort                  InetPortNumber,
      bfdSessState                    INTEGER,
      bfdSessRemoteHeardFlag          TruthValue,
      bfdSessDiag                     Unsigned32,
      bfdSessOperMode                 INTEGER,
      bfdSessDemandModeDesiredFlag    TruthValue,
      bfdSessEchoFuncModeDesiredFlag  TruthValue,
      bfdSessControlPlanIndepFlag     TruthValue,
      bfdSessAddrType                 InetAddressType,
      bfdSessAddr                     InetAddress,
      bfdSessDesiredMinTxInterval     BfdInterval,
      bfdSessDesiredMinRxInterval     BfdInterval,
      bfdSessDesiredMinEchoRxInterval BfdInterval,
      bfdSessDetectMult               Unsigned32,
      bfdSessStorType                 StorageType,
      bfdSessRowStatus                RowStatus,
      bfdSessAuthPresFlag             TruthValue,
      bfdSessAuthenticationType       INTEGER
   }

   bfdSessIndex  OBJECT-TYPE
      SYNTAX        BfdSessIndexTC
      MAX-ACCESS    not-accessible
      STATUS        current
      DESCRIPTION
              "This object contains an index used to represent a
               unique BFD session on this device."
      ::= { bfdSessEntry 1 }

   bfdSessApplicationId  OBJECT-TYPE
      SYNTAX        Unsigned32
      MAX-ACCESS    read-only
      STATUS        current
      DESCRIPTION
              "This object contains an index used to indicate
               a local application which owns or maintains this
               BFD session. For instance, the MPLS VPN process may
               maintain a subset of the total number of BFD
               sessions.  This application ID provides a convenient
               way to segregate sessions by the applications which
               maintain them."
      ::= { bfdSessEntry 2 }

   bfdSessDiscriminator            OBJECT-TYPE
      SYNTAX        Unsigned32 (1..4294967295)
      MAX-ACCESS    read-only
      STATUS        current
      DESCRIPTION
              "This object specifies the local discriminator for this BFD
               session, used to uniquely identify it."
      ::= { bfdSessEntry 3 }

   bfdSessRemoteDiscr OBJECT-TYPE
      SYNTAX        Unsigned32 (1..4294967295)
      MAX-ACCESS    read-only
      STATUS        current
      DESCRIPTION
              "This object specifies the session discriminator chosen
               by the remote system for this BFD session."
      ::= { bfdSessEntry 4 }

   bfdSessUdpPort OBJECT-TYPE
      SYNTAX      InetPortNumber
--      MAX-ACCESS  read-create
      MAX-ACCESS  read-only
      STATUS      current
      DESCRIPTION
              "The UDP Port for BFD. The default value is the
               well-known value for this port."
      REFERENCE
              "draft-katz-ward-bfd-02.txt and
               draft-raggarwa-mpls-bfd-00.txt"
      DEFVAL { 0 }
      ::= { bfdSessEntry 5 }

   bfdSessState OBJECT-TYPE
      SYNTAX   INTEGER {
               adminDown(1),
               down(2),
               init(3),
               up(4)
      }
      MAX-ACCESS   read-only
      STATUS   current
      DESCRIPTION
              "The perceived state of the BFD session."
      ::= { bfdSessEntry 6 }

   bfdSessRemoteHeardFlag OBJECT-TYPE
      SYNTAX        TruthValue
      MAX-ACCESS    read-only
      STATUS        current
      DESCRIPTION
              "This object specifies status of BFD packet reception from
               the remote system. Specifically, it is set to true(1) if
               the local system is actively receiving BFD packets from the
               remote system, and is set to false(2) if the local system
               has not received BFD packets recently (within the detection
               time) or if the local system is attempting to tear down
               the BFD session."
      ::= { bfdSessEntry 7 }

   bfdSessDiag OBJECT-TYPE
      SYNTAX      Unsigned32
      MAX-ACCESS  accessible-for-notify
      STATUS      current
      DESCRIPTION
              "A diagnostic code specifying the local system's reason
               for the last transition of the session from up(1)
               to some other state."
      ::= { bfdSessEntry 8 }

   bfdSessOperMode OBJECT-TYPE
      SYNTAX   INTEGER { asyncModeWEchoFun(1),
                         asynchModeWOEchoFun(2),
                         demandModeWEchoFunction(3),
                         demandModeWOEchoFunction(4)
      }
      MAX-ACCESS   read-only
      STATUS   current
      DESCRIPTION
              "This object specifies current operating mode that BFD
               session is operating in.

               A value of AsyncModeWEchoFun(1) ...
               A value of AsynchModeWOEchoFun(2) ...
               A value of DemandModeWEchoFunction(3) ...
               A value of DemandModeWOEchoFunction(4) ...
              "
      ::= { bfdSessEntry 9 }

   bfdSessDemandModeDesiredFlag OBJECT-TYPE
      SYNTAX        TruthValue
--      MAX-ACCESS    read-create
      MAX-ACCESS    read-only
      STATUS        current
      DESCRIPTION
              "This object indicates that the local system's
               desire to use Demand mode. Specifically, it is set
               to true(1) if the local system wishes to use
               Demand mode or false(2) if not"
      DEFVAL { false }
      ::= { bfdSessEntry 10 }

   bfdSessEchoFuncModeDesiredFlag OBJECT-TYPE
      SYNTAX        TruthValue
--      MAX-ACCESS    read-create
      MAX-ACCESS    read-only
      STATUS        current
      DESCRIPTION
              "This object indicates that the local system's
               desire to use Echo mode. Specifically, it is set
               to true(1) if the local system wishes to use
               Echo mode or false(2) if not"
      DEFVAL { false }
      ::= { bfdSessEntry 11 }

   bfdSessControlPlanIndepFlag     OBJECT-TYPE
      SYNTAX        TruthValue
--      MAX-ACCESS    read-create
      MAX-ACCESS    read-only
      STATUS        current
      DESCRIPTION
              "This object indicates that the local system's
               ability to continue to function through a disruption of
               the control plane. Specifically, it is set
               to true(1) if the local system BFD implementation is
               independent of the control plane. Otherwise, the
               value is set to false(2)"
      DEFVAL { false }
      ::= { bfdSessEntry 12 }

   bfdSessAddrType  OBJECT-TYPE
      SYNTAX        InetAddressType
--      MAX-ACCESS    read-create
      MAX-ACCESS    read-only
      STATUS        current
      DESCRIPTION
           "This object specifies IP address of the interface
            associated with this BFD session.

            Only values unknown(0), ipv4(1) or ipv6(2)
            have to be supported.

            A value of unknown(0) is allowed only when
            the outgoing interface is of type point-to-point, or
            when the BFD session is not associated with a specific
            interface.

            If any other unsupported values are attempted in a set
            operation, the agent MUST return an inconsistentValue
            error.
      "
      ::= { bfdSessEntry 13 }

   bfdSessAddr OBJECT-TYPE
      SYNTAX        InetAddress
--      MAX-ACCESS    read-create
      MAX-ACCESS    read-only
      STATUS        current
      DESCRIPTION
           "This object specifies IP address of the interface
            associated with this BFD session.
            It can also be used to enabled BFD on a specific
            interface. The value is set to zero when BFD session is not
            associated with a specific interface. "
      ::= { bfdSessEntry 14 }

   bfdSessDesiredMinTxInterval OBJECT-TYPE
      SYNTAX    BfdInterval
--      MAX-ACCESS    read-create
      MAX-ACCESS    read-only
      STATUS    current
      DESCRIPTION
       "This object specifies the minimum interval, in
        microseconds, that the local system would like to use when
             transmitting BFD Control packets."
      ::= { bfdSessEntry 15 }

   bfdSessDesiredMinRxInterval OBJECT-TYPE
      SYNTAX        BfdInterval
--      MAX-ACCESS    read-create
      MAX-ACCESS    read-only
      STATUS        current
      DESCRIPTION
            "This object specifies the minimum interval, in
             microseconds, between received  BFD Control packets the
             local system is capable of supporting."
      ::= { bfdSessEntry 16 }

   bfdSessDesiredMinEchoRxInterval OBJECT-TYPE
      SYNTAX        BfdInterval
--      MAX-ACCESS    read-create
      MAX-ACCESS    read-only
      STATUS        current
      DESCRIPTION
            "This object specifies the minimum interval, in
             microseconds, between received BFD Echo packets that this
             system is capable of supporting."
      ::= { bfdSessEntry 17 }

   bfdSessDetectMult OBJECT-TYPE
      SYNTAX        Unsigned32
--      MAX-ACCESS    read-create
      MAX-ACCESS    read-only
      STATUS        current
      DESCRIPTION
            "This object specifies the Detect time multiplier."
      ::= { bfdSessEntry 18 }

   bfdSessStorType  OBJECT-TYPE
      SYNTAX        StorageType
--      MAX-ACCESS    read-create
      MAX-ACCESS    read-only
      STATUS        current
      DESCRIPTION
          "This variable indicates the storage type for this
           object. Conceptual rows having the value
           'permanent' need not allow write-access to any
           columnar objects in the row."
      ::= { bfdSessEntry 19 }

   bfdSessRowStatus OBJECT-TYPE
      SYNTAX        RowStatus
--      MAX-ACCESS    read-create
      MAX-ACCESS    read-only
      STATUS        current
      DESCRIPTION
            "This variable is used to create, modify, and/or
             delete a row in this table. When a row in this
             table has a row in the active(1) state, no
             objects in this row can be modified except the
             bfdSessRowStatus and bfdSessStorageType."
      ::= { bfdSessEntry 20 }

   bfdSessAuthPresFlag OBJECT-TYPE
      SYNTAX        TruthValue
--      MAX-ACCESS    read-create
      MAX-ACCESS    read-only
      STATUS        current
      DESCRIPTION
              "This object indicates that the local system's
               desire to use Authentication. Specifically, it is set
               to true(1) if the local system wishes the session
               to be authenticated or false(2) if not"
      DEFVAL { false }
      ::= { bfdSessEntry 21 }

   bfdSessAuthenticationType OBJECT-TYPE
      SYNTAX      INTEGER { simplePassword(1),
                            keyedMD5(2),
                            meticulousKeyedMD5(3),
                            keyedSHA1(4),
                            meticulousKeyedSHA1(5)
      }
--      MAX-ACCESS    read-create
      MAX-ACCESS    read-only
      STATUS      current
      DESCRIPTION
           "The Authentication Type used for this BFD session. This
            field is valid only when the Authentication Present bit is set"
      ::= { bfdSessEntry 22 }

   -- BFD Session Performance Table

   bfdSessPerfTable OBJECT-TYPE
      SYNTAX        SEQUENCE OF BfdSessPerfEntry
      MAX-ACCESS    not-accessible
      STATUS        current
      DESCRIPTION
          "This table specifies BFD Session performance counters."
      ::= { bfdObjects 3 }

   bfdSessPerfEntry OBJECT-TYPE
      SYNTAX        BfdSessPerfEntry
      MAX-ACCESS    not-accessible
      STATUS        current
      DESCRIPTION
          "An entry in this table is created by a BFD-enabled node for
           every BFD Session. bfdCounterDiscontinuityTime is used to
           indicate potential discontinuity for all counter objects
           in this table."
      AUGMENTS    { bfdSessEntry }
      ::= { bfdSessPerfTable 1 }

   BfdSessPerfEntry ::= SEQUENCE {
     bfdSessPerfPktIn               Counter32,
     bfdSessPerfPktOut              Counter32,
     bfdSessUpTime                  TimeStamp,
     bfdSessPerfLastSessDownTime    TimeStamp,
     bfdSessPerfLastCommLostDiag    BfdDiag,
     bfdSessPerfSessUpCount         Counter32,
     bfdSessPerfDiscTime            TimeStamp,

     -- High Capacity Counters
     bfdSessPerfPktInHC             Counter64,
     bfdSessPerfPktOutHC            Counter64
     }

   -- Ed Note: should we add per-diag code counts here,

   bfdSessPerfPktIn OBJECT-TYPE
      SYNTAX      Counter32
      MAX-ACCESS  read-only
      STATUS      current
      DESCRIPTION
           "The total number of BFD messages received for this BFD
   session."
      ::= { bfdSessPerfEntry 1 }

   bfdSessPerfPktOut OBJECT-TYPE
      SYNTAX      Counter32
      MAX-ACCESS  read-only
      STATUS      current
      DESCRIPTION
           "The total number of BFD messages sent for this BFD session."
      ::= { bfdSessPerfEntry 2 }

   bfdSessUpTime OBJECT-TYPE
      SYNTAX       TimeStamp
      MAX-ACCESS   read-only
      STATUS       current
      DESCRIPTION
           "The value of sysUpTime on the most recent occasion at which
            the session came up. If no such up event exists this object
            contains a zero value."
      ::= { bfdSessPerfEntry 3 }

   bfdSessPerfLastSessDownTime OBJECT-TYPE
      SYNTAX       TimeStamp
      MAX-ACCESS   read-only
      STATUS       current
      DESCRIPTION
           "The value of sysUpTime on the most recent occasion at which
            the last time communication was lost with the neighbor. If
            no such down event exist this object contains a zero value."
      ::= { bfdSessPerfEntry 4 }

   bfdSessPerfLastCommLostDiag  OBJECT-TYPE
      SYNTAX       BfdDiag
      MAX-ACCESS   read-only
      STATUS       current
      DESCRIPTION
           "The BFD diag code for the last time communication was lost
            with the neighbor. If no such down event exists this object
            contains a zero value."
      ::= { bfdSessPerfEntry 5 }

   bfdSessPerfSessUpCount OBJECT-TYPE
      SYNTAX       Counter32
      MAX-ACCESS   read-only
      STATUS       current
      DESCRIPTION
           "The number of times this session has gone into the Up
            state since the router last rebooted."
      ::= { bfdSessPerfEntry 6 }

   bfdSessPerfDiscTime OBJECT-TYPE
      SYNTAX       TimeStamp
      MAX-ACCESS   read-only
      STATUS       current
      DESCRIPTION
         "The value of sysUpTime on the most recent occasion at
          which any one or more of the session counters suffered
          a discontinuity.

          The relevant counters are the specific instances associated
          with this BFD session of any Counter32 object contained in
          the BfdSessPerfTable. If no such discontinuities have occurred
          since the last re-initialization of the local management
          subsystem, then this object contains a zero value."
      ::= { bfdSessPerfEntry 7 }

   bfdSessPerfPktInHC OBJECT-TYPE
      SYNTAX       Counter64
      MAX-ACCESS   read-only
      STATUS       current
      DESCRIPTION
           "This value represents the total number of BFD messages
            received for this BFD session. It MUST be equal to the
            least significant 32 bits of bfdSessPerfPktIn
            if bfdSessPerfPktInHC is supported according to
            the rules spelled out in RFC2863."
      ::= { bfdSessPerfEntry 8 }

   bfdSessPerfPktOutHC OBJECT-TYPE
      SYNTAX       Counter64
      MAX-ACCESS   read-only
      STATUS       current
      DESCRIPTION
           "This value represents the total number of
            total number of BFD messages transmitted for this
            BFD session. It MUST be equal to the
           least significant 32 bits of bfdSessPerfPktIn
           if bfdSessPerfPktOutHC is supported according to
           the rules spelled out in RFC2863."
      ::= { bfdSessPerfEntry 9 }


   -- BFD Session Mapping Table

   bfdSessMapTable OBJECT-TYPE
      SYNTAX   SEQUENCE OF BfdSessMapEntry
      MAX-ACCESS   not-accessible
      STATUS   current
      DESCRIPTION
              "The BFD Session Mapping Table maps the complex
               indexing of the BFD sessions to the flat
               BFDIndex used in the BfdSessionTable.

               Implementors need to be aware that if the value of
               the bfdSessAddr (an OID) has more
               that 111 sub-identifiers, then OIDs of column
               instances in this table will have more than 128
               sub-identifiers and cannot be accessed using SNMPv1,
               SNMPv2c, or SNMPv3.
              "
      REFERENCE
              "BFD Version 0 (draft-katz-ward-bfd-02.txt)"
      ::= { bfdObjects 4 }

   bfdSessMapEntry OBJECT-TYPE
      SYNTAX   BfdSessMapEntry
      MAX-ACCESS   not-accessible
      STATUS   current
      DESCRIPTION
              "The BFD Session Entry describes BFD session
               that is mapped to this index.

               Implementors need to be aware that if the value of
               the mplsInSegmentMapLabelPtrIndex (an OID) has more
               that 111 sub-identifiers, then OIDs of column
               instances in this table will have more than 128
               sub-identifiers and cannot be accessed using SNMPv1,
               SNMPv2c, or SNMPv3."
      INDEX { bfdSessApplicationId,
              bfdSessDiscriminator,
              bfdSessAddrType,
              bfdSessAddr
            }
      ::= { bfdSessMapTable 1 }

   BfdSessMapEntry ::= SEQUENCE {
      bfdSessMapBfdIndex            BfdSessIndexTC
   }

   bfdSessMapBfdIndex OBJECT-TYPE
      SYNTAX        BfdSessIndexTC
      MAX-ACCESS    read-only
      STATUS        current
      DESCRIPTION
          "This object specifies the BfdIndex referred to by
           the indexes of this row. In essence, a mapping is
           provided between these indexes and the BfdSessTable."
      ::= { bfdSessMapEntry 1 }

   -- Notification Configuration

   bfdSessNotificationsEnable OBJECT-TYPE
      SYNTAX        TruthValue
--      MAX-ACCESS   read-write
      MAX-ACCESS   read-only
      STATUS        current
      DESCRIPTION
          "If this object is set to true(1), then it enables
           the emission of bfdSessUp and bfdSessDown
           notifications; otherwise these notifications are not
           emitted."
      REFERENCE
          "See also RFC3413 for explanation that
           notifications are under the ultimate control of the
           MIB modules in this document."
      DEFVAL { false }
      ::= { bfdScalarObjects 4 }

   bfdSessUp NOTIFICATION-TYPE
      OBJECTS     { bfdSessDiag, -- low range value
                    bfdSessDiag  -- high range value
      }
      STATUS      current
      DESCRIPTION
          "This notification is generated when the
           bfdSessState object for one or more contiguous
           entries in bfdSessTable are about to enter the up(2)
           state from some other state. The included values of
           bfdSessDiag MUST both be set equal to this
           new state (i.e: up(1)).  The two instances of
           bfdSessDiag in this notification indicate the range
           of indexes that are affected.  Note that all the indexes
           of the two ends of the range can be derived from the
           instance identifiers of these two objects.  For the
           cases where a contiguous range of sessions
           have transitioned into the up(1) state at roughly
           the same time, the device SHOULD issue a single
           notification for each range of contiguous indexes in
           an effort to minimize the emission of a large number
           of notifications.  If a notification has to be
           issued for just a single bfdSessEntry, then
           the instance identifier (and values) of the two
           bfdSessDiag objects MUST be the identical."
      ::= { bfdNotifications 1 }

   bfdSessDown NOTIFICATION-TYPE
      OBJECTS     { bfdSessDiag, -- low range value
                    bfdSessDiag  -- high range value
      }
      STATUS      current
      DESCRIPTION
          "This notification is generated when the
           bfdSessState object for one or more contiguous
           entries in bfdSessTable are about to enter the down(4)
           or adminDown(5) states from some other state. The included
           values of bfdSessDiag MUST both be set equal to this
           new state (i.e: down(4) or adminDown(5)).  The two instances
           of bfdSessDiag in this notification indicate the range
           of indexes that are affected.  Note that all the indexes
           of the two ends of the range can be derived from the
           instance identifiers of these two objects.  For
           cases where a contiguous range of sessions
           have transitioned into the down(4) or adminDown(5) states
           at roughly the same time, the device SHOULD issue a single
           notification for each range of contiguous indexes in
           an effort to minimize the emission of a large number
           of notifications.  If a notification has to be
           issued for just a single bfdSessEntry, then
           the instance identifier (and values) of the two
           bfdSessDiag objects MUST be the identical."
      ::= { bfdNotifications 2 }

   -- Ed Note: We need to add notification for changes
   -- when the two ends automatically negotiate to a new detection time
   -- value or when detection multiplier changes.
   -- Similarly, changes in the operating mode (bfdSessOperMode)
   -- also need to be notified.

   -- Module compliance.

   bfdGroups
      OBJECT IDENTIFIER ::= { bfdConformance 1 }

   bfdCompliances
      OBJECT IDENTIFIER ::= { bfdConformance 2 }

   -- Compliance requirement for fully compliant implementations.

   bfdModuleFullCompliance MODULE-COMPLIANCE
      STATUS       current
      DESCRIPTION "Compliance statement for agents that provide full
                   support for BFD-MIB. Such devices can
                   then be monitored and also be configured using
                   this MIB module."

      MODULE -- This module.
      MANDATORY-GROUPS {
            bfdSessionGroup,
            bfdSessionPerfGroup,
            bfdSessionPerfHCGroup,
            bfdNotificationGroup
      }

--      GROUP        bfdSessionPerfHCGroup
--      DESCRIPTION "This group is mandatory for those bfdPerfTable
--                   entries for which any of the objects
--                   bfdSessPerfPktInHC or bfdSessPerfPktOutHC
--                   wraps around too quickly
--                   based on the criteria specified in RFC 2863 for
--                   high-capacity counters."
--
--      GROUP        bfdNotificationGroup
--      DESCRIPTION "This group is only mandatory for those
--                   implementations which can efficiently implement
--                   the notifications contained in this group."
--
      OBJECT       bfdSessAddrType
      SYNTAX       InetAddressType {
                                    unknown(0),
                                    ipv4(1),
                                    ipv6(2)
                                    }
      DESCRIPTION "Only unknown(0), ipv4(1) and ipv6(2) support
                   is required."

      OBJECT       bfdSessAddr
      SYNTAX       InetAddress (SIZE(0|4|16))
      DESCRIPTION "An implementation is only required to support
                   unknown(0), ipv4(1) and ipv6(2) sizes."

      ::= { bfdCompliances 1 }

   -- Read-Only Conformance TBD...


   -- Units of conformance.

   bfdSessionGroup OBJECT-GROUP
      OBJECTS {
                bfdSessNotificationsEnable,
                bfdAdminStatus,
                bfdVersionNumber,
                bfdSessApplicationId,
                bfdSessDiscriminator,
                bfdSessAddrType,
                bfdSessAddr,
                bfdSessRemoteDiscr,
                bfdSessUdpPort,
                bfdSessState,
                bfdSessRemoteHeardFlag,
                bfdSessDiag,
                bfdSessOperMode,
                bfdSessDemandModeDesiredFlag,
                bfdSessEchoFuncModeDesiredFlag,
                bfdSessControlPlanIndepFlag,
                bfdSessDesiredMinTxInterval,
                bfdSessDesiredMinRxInterval,
                bfdSessDesiredMinEchoRxInterval,
                bfdSessDetectMult,
                bfdSessStorType,
                bfdSessRowStatus,
                bfdSessMapBfdIndex,
                bfdSessAuthPresFlag,
                bfdSessAuthenticationType
      }
      STATUS  current
      DESCRIPTION
             "Collection of objects needed for BFD sessions."
      ::= { bfdGroups 1 }


   bfdSessionPerfGroup OBJECT-GROUP
      OBJECTS {
                bfdSessPerfPktIn,
                bfdSessPerfPktOut,
                bfdSessUpTime,
                bfdSessPerfLastSessDownTime,
                bfdSessPerfLastCommLostDiag,
                bfdSessPerfSessUpCount,
                bfdSessPerfDiscTime
      }
      STATUS  current
      DESCRIPTION
             "Collection of objects needed to monitor the
              performance of BFD sessions."
      ::= { bfdGroups 2 }

   bfdSessionPerfHCGroup OBJECT-GROUP
      OBJECTS {
               bfdSessPerfPktInHC,
               bfdSessPerfPktOutHC
      }
      STATUS  current
      DESCRIPTION
             "Collection of objects needed to monitor the
              performance of BFD sessions for which the
              values of bfdSessPerfPktIn, bfdSessPerfPktOut
              wrap around too quickly."
      ::= { bfdGroups 3 }

   bfdNotificationGroup NOTIFICATION-GROUP
      NOTIFICATIONS {
                bfdSessUp,
                bfdSessDown
      }
      STATUS  current
      DESCRIPTION
             "Set of notifications implemented in this
              module."

      ::= { bfdGroups 4 }

   END
