Reference record for OID 1.3.6.1.3.7.1.1.4


parent
1.3.6.1.3.7.1.1 (dot4Entry)
node code
4
node name
dot4Commands
dot oid
1.3.6.1.3.7.1.1.4
type
OBJECT-TYPE
asn1 oid
  • {iso(1) identified-organization(3) dod(6) internet(1) experimental(3) dot4(7) dot4Table(1) dot4Entry(1) dot4Commands(4)}
  • {iso(1) org(3) dod(6) internet(1) experimental(3) dot4(7) dot4Table(1) dot4Entry(1) dot4Commands(4)}
  • {iso(1) iso-identified-organization(3) dod(6) internet(1) experimental(3) dot4(7) dot4Table(1) dot4Entry(1) dot4Commands(4)}
    • iri oid
  • /iso/identified-organization/dod/internet/experimental/dot4/dot4Table/dot4Entry/dot4Commands
  • /iso/org/dod/internet/experimental/dot4/dot4Table/dot4Entry/dot4Commands
  • /iso/iso-identified-organization/dod/internet/experimental/dot4/dot4Table/dot4Entry/dot4Commands
    • iri by oid_info
    /ISO/Identified-Organization/6/1/3/7/1/1/4

    Description by oid_info

    dot4Commands OBJECT-TYPE
    SYNTAX INTEGER {
    no-op(1),
    enterRing(2),
    exitRing(3),
    reset(4),
    initialize(5)
    }
    ACCESS read-write
    STATUS mandatory
    DESCRIPTION
    "Setting this object causes the station
    to change the state of the interface as
    indicated by the specified value. An
    initialize(5) command causes the
    interfaceto load its operational
    parameters from its initialization
    parameters; the value of
    dot4InitInRingDesired determines
    whether the station tries to enter the
    logical ring immediately.
    Note that the 802.4 specification
    suggests a station remain Offline after a

    emote Network Management reset(4),
    until a local Network Management
    initialize(5) is performed.
    Setting this object to a value of
    no-op(1) has no effect. When read,
    this object always has the value no-op(1)."
    View at oid-info.com

    Description by mibdepot

    Setting this object causes the station
    to change the state of the interface as
    indicated by the specified value. An
    initialize(5) command causes the
    interfaceto load its operational
    parameters from its initialization
    parameters; the value of
    dot4InitInRingDesired determines
    whether the station tries to enter the
    logical ring immediately.
    Note that the 802.4 specification
    suggests a station remain Offline after a
    'remote Network Management' reset(4),
    until a 'local Network Management'
    initialize(5) is performed.
    Setting this object to a value of
    no-op(1) has no effect. When read,
    this object always has the value no-op(1).

    Parsed from file rfc1230-IEEE-802.4-Token-Bus.mib.txt
    Company: None
    Module: RFC1230-MIB

    Description by circitor

    Setting this object causes the station
    to change the state of the interface as
    indicated by the specified value. An
    initialize(5) command causes the
    interfaceto load its operational
    parameters from its initialization
    parameters; the value of
    dot4InitInRingDesired determines
    whether the station tries to enter the
    logical ring immediately.
    Note that the 802.4 specification
    suggests a station remain Offline after a
    'remote Network Management' reset(4),
    until a 'local Network Management'
    initialize(5) is performed.
    Setting this object to a value of
    no-op(1) has no effect. When read,
    this object always has the value no-op(1).

    Parsed from file RFC1230-MIB.mib
    Module: RFC1230-MIB

    Information by oid_info

    Automatically extracted from RFC1230

    Information by mibdepot

    dot4Commands OBJECT-TYPE
                     SYNTAX  INTEGER {
                                 no-op(1),
                                 enterRing(2),
                                 exitRing(3),
                                 reset(4),
                                 initialize(5)
                             }
                     ACCESS  read-write
                     STATUS  mandatory
                     DESCRIPTION
                             "Setting this object causes the station
                             to change the state of the interface as
                             indicated by the specified value.  An
                             initialize(5) command causes the
                             interfaceto load its operational
                             parameters from its initialization
                             parameters; the value of
                             dot4InitInRingDesired determines
                             whether the station tries to enter the
                             logical ring immediately.
                                 Note that the 802.4 specification
                             suggests a station remain Offline after a
                             'remote Network Management' reset(4),
                             until a 'local Network Management'
                             initialize(5) is performed.
                                 Setting this object to a value of
                             no-op(1) has no effect.  When read,
                             this object always has the value no-op(1)."
                     ::=  { dot4Entry 4 }

    Information by circitor

    dot4Commands OBJECT-TYPE
                     SYNTAX  INTEGER {
                                 no-op(1),
                                 enterRing(2),
                                 exitRing(3),
                                 reset(4),
                                 initialize(5)
                             }
                     ACCESS  read-write
                     STATUS  mandatory
                     DESCRIPTION
                             "Setting this object causes the station
                             to change the state of the interface as
                             indicated by the specified value.  An
                             initialize(5) command causes the
                             interfaceto load its operational
                             parameters from its initialization
                             parameters; the value of
                             dot4InitInRingDesired determines
                             whether the station tries to enter the
                             logical ring immediately.
                                 Note that the 802.4 specification
                             suggests a station remain Offline after a
                             'remote Network Management' reset(4),
                             until a 'local Network Management'
                             initialize(5) is performed.
                                 Setting this object to a value of
                             no-op(1) has no effect.  When read,
                             this object always has the value no-op(1)."
                     ::=  { dot4Entry 4 }

    First Registration Authority (recovered by parent 1.3.6)

    Defense Communication Agency

    Current Registration Authority (recovered by parent 1.3.6.1.3)

    Internet Assigned Numbers Authority

    Brothers (18)

    OIDNameSub childrenSub Nodes TotalDescription
    1.3.6.1.3.7.1.1.1 dot4IfIndex 0 0 The value of this object identifies the
    802.4 interface for which this entry
    contains management information. The
    value of this o…
    1.3.6.1.3.7.1.1.2 dot4Options 0 0 The optional parts of the 802.4
    specification which are in use by this
    station. The options of the 802.4
    specification are repres…
    1.3.6.1.3.7.1.1.3 dot4State 0 0 The current state of the 802.4
    interface. The value of other(1) is
    used if the state is unknown
    (e.g., due to an error condition).
    1.3.6.1.3.7.1.1.5 dot4MacAddrLen 0 0 This object indicates the size of MAC
    addresses interpreted by this station.
    1.3.6.1.3.7.1.1.6 dot4NextStation 0 0 The MAC address of this station's
    successor in the logical ring.
    1.3.6.1.3.7.1.1.7 dot4PreviousStation 0 0 The source MAC address of the last token
    addressed to this station.
    1.3.6.1.3.7.1.1.8 dot4SlotTime 0 0 The maximum time any station need wait
    for an immediate MAC-level response from
    another station.
    This value must the same in all s…
    1.3.6.1.3.7.1.1.9 dot4LastTokenRotTime 0 0 The observed token rotation time for the
    last token rotation, timed from token
    arrival to token arrival. A value of
    zero indicate…
    1.3.6.1.3.7.1.1.10 dot4HiPriTokenHoldTime 0 0 The maximum duration for which a station
    can hold the token to transmit frames of
    access class 6 (if the priority option is
    implem…
    1.3.6.1.3.7.1.1.11 dot4TargetRotTimeClass4 0 0 If the priority scheme is being used,
    this value specifies a limit on how long
    a station can transmit frames at access
    class 4. T…
    1.3.6.1.3.7.1.1.12 dot4TargetRotTimeClass2 0 0 If the priority scheme is being used,
    this value specifies a limit on how long
    a station can transmit frames at access
    class 2. T…
    1.3.6.1.3.7.1.1.13 dot4TargetRotTimeClass0 0 0 If the priority scheme is being used,
    this value specifies a limit on how long
    a station can transmit frames at access
    class 0. T…
    1.3.6.1.3.7.1.1.14 dot4TargetRotTimeRingMaint 0 0 A value used to limit the duration of a
    token rotation. If the duration of a
    token rotation exceeds this value, the
    station will …
    1.3.6.1.3.7.1.1.15 dot4RingMaintTimerInitValue 0 0 The value to which the
    dot4TargetRotTimeRingMaint is set, each
    time the station enters the ring.
    A large value will cause the stat…
    1.3.6.1.3.7.1.1.16 dot4MaxInterSolicitCount 0 0 The maximum number of consecutive token
    rotations without soliciting for a
    successor. If this count expires, the
    station opens th…
    1.3.6.1.3.7.1.1.17 dot4MaxRetries 0 0 The maximum number of retries of a
    Request-with-Response (RWR) frame. If
    the RWR option is not in use, this object
    has the value …
    1.3.6.1.3.7.1.1.18 dot4MinPostSilencePreambLen 0 0 The minimum number of octets of preamble
    on the first frame transmitted by this
    station after a period of 'transmitted'
    silence.
    1.3.6.1.3.7.1.1.19 dot4StandardRevision 0 0 The Revision number of the 802.4 standard
    implemented by this station.