Time limitation for an open session. A value of zero indicates that
the Clear timer is not used.
Parsed from file Rad0485.MIB.txt
Company: None
Module: RAD-MIB
Time limitation for an open session. A value of zero indicates that
the Clear timer is not used.
Parsed from file RAD-MIB.mib
Module: RAD-MIB
Vendor: Rad Data Communications
Module: RAD-MIB (rad-mib.mib)
Type: TABULAR
Access: read-write
Syntax: Integer32
(
0..255 )
Automatically extracted from www.mibdepot.com
pktSwchChannelClearTimerS OBJECT-TYPE SYNTAX Integer32 (0..255) MAX-ACCESS read-write STATUS current DESCRIPTION "Time limitation for an open session. A value of zero indicates that the Clear timer is not used." ::= { pktSwchChannelSEntry 15 }
pktSwchChannelClearTimerS OBJECT-TYPE SYNTAX Integer32 (0..255) MAX-ACCESS read-write STATUS current DESCRIPTION "Time limitation for an open session. A value of zero indicates that the Clear timer is not used." ::= { pktSwchChannelSEntry 15 }
OID | Name | Sub children | Sub Nodes Total | Description |
---|---|---|---|---|
1.3.6.1.4.1.164.8.2.2.1.1.1 | pktSwchChannelIfIndexS | 0 | 0 | This is used as the index for the channel table. |
1.3.6.1.4.1.164.8.2.2.1.1.2 | pktSwchChannelNumberS | 0 | 0 | The number by which a channel is identified. |
1.3.6.1.4.1.164.8.2.2.1.1.3 | pktSwchChannelProfileS | 0 | 0 | The profile that the channel uses for command mode operations. |
1.3.6.1.4.1.164.8.2.2.1.1.4 | pktSwchChannelOutCallProfileS | 0 | 0 | The number of the profile that will be used during an outgoing call on the channel. |
1.3.6.1.4.1.164.8.2.2.1.1.5 | pktSwchChannelInCallProfileS | 0 | 0 | The number of the profile that will be used during an incoming call on the channel. |
1.3.6.1.4.1.164.8.2.2.1.1.6 | pktSwchChannelRemoteProfileS | 0 | 0 | The number of the profile that will be downloaded to the remote PAD at the beginning of a new call. |
1.3.6.1.4.1.164.8.2.2.1.1.7 | pktSwchChannelAutocallIdS | 0 | 0 | Selects the mnemonic (call ID) to be used as the first alternative. A value of zero indicates that the autocall function is disa… |
1.3.6.1.4.1.164.8.2.2.1.1.8 | pktSwchChannelAlterAutocallIdS | 0 | 0 | Selects the alternate mnemonic for the autocall function. A value of zero indicates that the alternate destination is not used. |
1.3.6.1.4.1.164.8.2.2.1.1.9 | pktSwchChannelAutocallRetriesS | 0 | 0 | The number of autocall retries if the autocall setup request is rejected with a busy cause. |
1.3.6.1.4.1.164.8.2.2.1.1.10 | pktSwchChannelAutocallIntervalS | 0 | 0 | The interval in seconds between consecutive autocall retries. |
1.3.6.1.4.1.164.8.2.2.1.1.11 | pktSwchChannelCallAliasS | 0 | 0 | The alias to be sent after the call is set up. A value of zero indicates that alias sending is disabled. The aliases are config… |
1.3.6.1.4.1.164.8.2.2.1.1.12 | pktSwchChannelSubAddress1S | 0 | 0 | The first subaddress for the channel. |
1.3.6.1.4.1.164.8.2.2.1.1.13 | pktSwchChannelSubAddress2S | 0 | 0 | The second subaddress for the channel. |
1.3.6.1.4.1.164.8.2.2.1.1.14 | pktSwchChannelNUISEntry | 0 | 0 | The number corresponding to the NUI information to be sent. This number is the same as the pktSwchNuiGroupId. |
1.3.6.1.4.1.164.8.2.2.1.1.16 | pktSwchChannelOptionsS | 0 | 0 | This controls the use of gneral non-correlated channel options. The value is a sum of values (powers of two), where each value i… |
1.3.6.1.4.1.164.8.2.2.1.1.17 | pktSwchChannelClear | 0 | 0 | The Clearing Channel operation disconnects all sessions |
1.3.6.1.4.1.164.8.2.2.1.1.18 | pktSwchChannelCopyTo | 0 | 0 | The destination channel number, to which the Copy is performed. |
1.3.6.1.4.1.164.8.2.2.1.1.19 | pktSwchChannelCopyToWMask | 0 | 0 | The destination channel number, to which the Copy with Mask is performed. |
1.3.6.1.4.1.164.8.2.2.1.1.20 | pktSwchChannelCopyMask | 0 | 0 | The selected configuration parameters to be copied from the source channel to the target channels. The value is a sum of values (… |