This is the total maximum outgoing throughput that is
available for all frame mode calls on the port. If the
sum of the outgoing throughput requested by a call
and wfFrSwSigTotalOutCurrentThroughput is in excess of
this value, the call is rejected.
Parsed from file frsw.mib.txt
Company: None
Module: Wellfleet-FRSW-MIB
This is the total maximum outgoing throughput that is
available for all frame mode calls on the port. If the
sum of the outgoing throughput requested by a call
and wfFrSwSigTotalOutCurrentThroughput is in excess of
this value, the call is rejected.
Parsed from file Wellfleet-FRSW-MIB.mib
Module: Wellfleet-FRSW-MIB
Vendor: Wellfleet
Module: Wellfleet-FRSW-MIB
[Automatically extracted from oidview.com]
wfFrSwSigTotalOutNegotiableThroughput OBJECT-TYPE SYNTAX INTEGER (0..2147483647) ACCESS read-write STATUS mandatory DESCRIPTION " This is the total maximum outgoing throughput that is available for all frame mode calls on the port. If the sum of the outgoing throughput requested by a call and wfFrSwSigTotalOutCurrentThroughput is in excess of this value, the call is rejected. " DEFVAL { 2147483647 } ::= { wfFrSwSigEntry 16 }
wfFrSwSigTotalOutNegotiableThroughput OBJECT-TYPE SYNTAX INTEGER (0..2147483647) ACCESS read-write STATUS mandatory DESCRIPTION " This is the total maximum outgoing throughput that is available for all frame mode calls on the port. If the sum of the outgoing throughput requested by a call and wfFrSwSigTotalOutCurrentThroughput is in excess of this value, the call is rejected. " DEFVAL { 2147483647 } ::= { wfFrSwSigEntry 16 }
| OID | Name | Sub children | Sub Nodes Total | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.18.3.5.9.6.12.1.1 | wfFrSwSigDelete | 0 | 0 | Indication to delete this instance |
| 1.3.6.1.4.1.18.3.5.9.6.12.1.2 | wfFrSwSigCircuit | 0 | 0 | The circuit number for this frame relay access channel |
| 1.3.6.1.4.1.18.3.5.9.6.12.1.3 | wfFrSwSigSvcDlciLow | 0 | 0 | Lowest DLCI to be used for SVC, the default value is for 2 octet frame header |
| 1.3.6.1.4.1.18.3.5.9.6.12.1.4 | wfFrSwSigSvcDlciHigh | 0 | 0 | Highest DLCI to be used for SVC, the default value is for 2 octet frame header. |
| 1.3.6.1.4.1.18.3.5.9.6.12.1.5 | wfFrSwSigDlciAssign | 0 | 0 | Determines if DLCI's are assigned starting at wfFrSwSigSvcDlciHigh and working towards wfFrSwSigSvcDlciLow or vice versa. |
| 1.3.6.1.4.1.18.3.5.9.6.12.1.6 | wfFrSwSigMaxNumOfSvcs | 0 | 0 | Indicates the maximum number of simultaneous switched virtual circuits allowed on the logical line. |
| 1.3.6.1.4.1.18.3.5.9.6.12.1.7 | wfFrSwSigNumOfSvcsInUse | 0 | 0 | Indicates the number of switched virtual circuits in use on the logical line. |
| 1.3.6.1.4.1.18.3.5.9.6.12.1.8 | wfFrSwSigDefaultThroughput | 0 | 0 | This value is used by the network in the Link Layer Core Parameters IE incoming & outgoing throughput fields when they are not in… |
| 1.3.6.1.4.1.18.3.5.9.6.12.1.9 | wfFrSwSigDefaultMinAcceptThroughput | 0 | 0 | This value is used by the network in the Link Layer Core Parameters IE incoming & outgoing minimum acceptable throughput fields w… |
| 1.3.6.1.4.1.18.3.5.9.6.12.1.10 | wfFrSwSigDefaultBc | 0 | 0 | This value is used by the network in the Link Layer Core Parameters IE incoming & outgoing Bc fields when they are not included i… |
| 1.3.6.1.4.1.18.3.5.9.6.12.1.11 | wfFrSwSigDefaultBe | 0 | 0 | This value is used by the network in the Link Layer Core Parameters IE incoming & outgoing Be fields when they are not included i… |
| 1.3.6.1.4.1.18.3.5.9.6.12.1.12 | wfFrSwSigMaxInThroughputPerSvc | 0 | 0 | This is the maximum incoming throughput that any single SVC may negotiate for a call. Calls requesting in excess of this attribu… |
| 1.3.6.1.4.1.18.3.5.9.6.12.1.13 | wfFrSwSigMaxOutThroughputPerSvc | 0 | 0 | This is the maximum outgoing throughput that any single SVC may negotiate for a call. Calls requesting in excess of this attribu… |
| 1.3.6.1.4.1.18.3.5.9.6.12.1.14 | wfFrSwSigTotalInNegotiableThroughput | 0 | 0 | This is the total maximum incoming throughput that is available for all frame mode calls on the port. If the sum of the incoming… |
| 1.3.6.1.4.1.18.3.5.9.6.12.1.15 | wfFrSwSigTotalInCurrentThroughput | 0 | 0 | This is the total incoming throughput that has been negotiated for use by all SVC's on the port. |
| 1.3.6.1.4.1.18.3.5.9.6.12.1.17 | wfFrSwSigTotalOutCurrentThroughput | 0 | 0 | This is the total incoming throughput that has been negotiated for use by all SVC's on the port. |
| 1.3.6.1.4.1.18.3.5.9.6.12.1.18 | wfFrSwSigXNetClearingDisable | 0 | 0 | If cross-net polling (wfFrSwDlcmiCrossNetEnable) is enabled on this interface, and the error threshold (wfFrSwDlcmiCrossNetErrorT… |
| 1.3.6.1.4.1.18.3.5.9.6.12.1.19 | wfFrSwSigCallingPartyIEMandatory | 0 | 0 | Reject the call if the Calling Party IE is absent in the setup message or if the provided Calling Party IE fails address authenti… |
| 1.3.6.1.4.1.18.3.5.9.6.12.1.20 | wfFrSwSigT301 | 0 | 0 | Timer number: T301 default time-out: 3 min state of call: call initiated cause for start: incoming setup no… |
| 1.3.6.1.4.1.18.3.5.9.6.12.1.21 | wfFrSwSigT303 | 0 | 0 | Timer number: T303 default time-out: 4 s state of call: call present cause for start: outgoing setup normal… |
| 1.3.6.1.4.1.18.3.5.9.6.12.1.22 | wfFrSwSigT305 | 0 | 0 | Timer number: T305 default time-out: 30 s state of call: disconnect ind cause for start: outgoing disconne… |
| 1.3.6.1.4.1.18.3.5.9.6.12.1.23 | wfFrSwSigT308 | 0 | 0 | Timer number: T308 default time-out: 4 s state of call: release req cause for start: outgoing release norma… |
| 1.3.6.1.4.1.18.3.5.9.6.12.1.24 | wfFrSwSigT310 | 0 | 0 | Timer number: T310 default time-out: 10 s state of call: incoming call proceeding cause for start: incomin… |
| 1.3.6.1.4.1.18.3.5.9.6.12.1.25 | wfFrSwSigT322 | 0 | 0 | Timer number: T322 default time-out: 4 s state of call: any call state cause for start: outgoing status en… |
| 1.3.6.1.4.1.18.3.5.9.6.12.1.26 | wfFrSwSigInSetupPkts | 0 | 0 | number of incoming setup packets |
| 1.3.6.1.4.1.18.3.5.9.6.12.1.27 | wfFrSwSigInCallProceedingPkts | 0 | 0 | number of incoming call proceeding packets |
| 1.3.6.1.4.1.18.3.5.9.6.12.1.28 | wfFrSwSigInConnectPkts | 0 | 0 | number of incoming connect packets |
| 1.3.6.1.4.1.18.3.5.9.6.12.1.29 | wfFrSwSigInDisconnectPkts | 0 | 0 | number of incoming disconnect packets |
| 1.3.6.1.4.1.18.3.5.9.6.12.1.30 | wfFrSwSigInReleasePkts | 0 | 0 | number of incoming release packets |
| 1.3.6.1.4.1.18.3.5.9.6.12.1.31 | wfFrSwSigInReleaseCompletePkts | 0 | 0 | number of incoming release complete packets |
| 1.3.6.1.4.1.18.3.5.9.6.12.1.32 | wfFrSwSigInStatusEnquiryPkts | 0 | 0 | number of incoming status enquiry packets |
| 1.3.6.1.4.1.18.3.5.9.6.12.1.33 | wfFrSwSigInStatusPkts | 0 | 0 | number of incoming status packets |
| 1.3.6.1.4.1.18.3.5.9.6.12.1.34 | wfFrSwSigInUnknownPkts | 0 | 0 | number of incoming unknown packets |
| 1.3.6.1.4.1.18.3.5.9.6.12.1.35 | wfFrSwSigOutSetupPkts | 0 | 0 | number of outgoing setup packets |
| 1.3.6.1.4.1.18.3.5.9.6.12.1.36 | wfFrSwSigOutCallProceedingPkts | 0 | 0 | number of outgoing call proceeding packets |
| 1.3.6.1.4.1.18.3.5.9.6.12.1.37 | wfFrSwSigOutConnectPkts | 0 | 0 | number of outgoing connect packets |
| 1.3.6.1.4.1.18.3.5.9.6.12.1.38 | wfFrSwSigOutDisconnectPkts | 0 | 0 | number of outgoing disconnect packets |
| 1.3.6.1.4.1.18.3.5.9.6.12.1.39 | wfFrSwSigOutReleasePkts | 0 | 0 | number of outgoing release packets |
| 1.3.6.1.4.1.18.3.5.9.6.12.1.40 | wfFrSwSigOutReleaseCompletePkts | 0 | 0 | number of outgoing release packest |
| 1.3.6.1.4.1.18.3.5.9.6.12.1.41 | wfFrSwSigOutStatusEnquiryPkts | 0 | 0 | number of outgoing status enquiry packets |
| 1.3.6.1.4.1.18.3.5.9.6.12.1.42 | wfFrSwSigOutStatusPkts | 0 | 0 | number of outgoing status packets |
| 1.3.6.1.4.1.18.3.5.9.6.12.1.43 | wfFrSwSigRejectedConnRequests | 0 | 0 | number of connections rejected |
| 1.3.6.1.4.1.18.3.5.9.6.12.1.44 | wfFrSwSigNwrkAbortedConnections | 0 | 0 | number of connections aborted by network |
| 1.3.6.1.4.1.18.3.5.9.6.12.1.45 | wfFrSwSigL2Resets | 0 | 0 | number of L2 resets |
| 1.3.6.1.4.1.18.3.5.9.6.12.1.46 | wfFrSwSigDlciIEAllowed | 0 | 0 | Reject the call if the Dlci IE is present in the setup message and wfFrSwSigDlciIEAllowed is set to disabled. |
| 1.3.6.1.4.1.18.3.5.9.6.12.1.47 | wfFrSwSigX213PriorityIEAllowed | 0 | 0 | Reject the call if the X213 Priority IE is present in setup message and wfFrSwSigX213PriorityIEAllowed is set to disabled. |
| 1.3.6.1.4.1.18.3.5.9.6.12.1.48 | wfFrSwSigMaximumBe | 0 | 0 | This value is the maximum allowed Be for a SVC connection |