Vendor: Compaq
Module: NETWORTH-FASTPIPES-MIB (Compaq-Fpipes.mib)
Type: OBJ ID
Access:
Syntax:
Automatically extracted from www.mibdepot.com
nwFastPipes OBJECT IDENTIFIER ::= { networthInternetworking 2 }
| OID | Name | Sub children | Sub Nodes Total | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.215.1.2.2.1 | nwfpProductType | 1 | 1 | The switch product type based on whether the switch is modular or nonmodular, has one of four uplinks or none, and has routing o… |
| 1.3.6.1.4.1.215.1.2.2.2 | nwfpReset | 1 | 1 | Setting this object to reset(2) will cause the FastPipes to perform a hardware reset within approximately 5 seconds. Setting this… |
| 1.3.6.1.4.1.215.1.2.2.3 | nwfpCurrentSoftwareVersion | 1 | 1 | The version of software currently running on the switch. The version is specified in ASCII format |
| 1.3.6.1.4.1.215.1.2.2.4 | nwfpFutureSoftwareVersion | 1 | 1 | The version of software the switch will run after the next reset. If this variable is different than nwfpCurrentSoftwareVersion,… |
| 1.3.6.1.4.1.215.1.2.2.5 | nwfpTFTPServerIPAddress | 1 | 1 | The IP address of the TFTP Server to which the FastPipes will send its next TFTP request. |
| 1.3.6.1.4.1.215.1.2.2.6 | nwfpCurrentUplinkSoftwareVers | 1 | 1 | The version of software currently running on the switch's Uplink Card. The version is an ASCI string of the form. |
| 1.3.6.1.4.1.215.1.2.2.7 | nwfpFutureUplinkSoftwareVers | 1 | 1 | The version of software the switch's Uplink Card will run after the next reset. If this variable is different than nwfpCurrentUpl… |
| 1.3.6.1.4.1.215.1.2.2.8 | nwfpLastFailureReason | 1 | 1 | The last error that caused a switch failure. A value of zero (0) indicates that there has not been a switch failure since the n… |
| 1.3.6.1.4.1.215.1.2.2.9 | nwfpEEPROMVersion | 1 | 1 | The hardware EEPROM version. The string 'unknown' is returned if the value is not known. |
| 1.3.6.1.4.1.215.1.2.2.10 | nwfpManufactureDate | 1 | 1 | The hardware manufacture date. The string 'unknown' is returned if the value is not known. |
| 1.3.6.1.4.1.215.1.2.2.11 | nwfpAuthErrIPaddress | 1 | 1 | The IP address of the device that sent the SNMP packet that caused an authentication error trap to be issued by the switch. |
| 1.3.6.1.4.1.215.1.2.2.12 | nwfpRAMsize | 1 | 1 | The size of RAM. |
| 1.3.6.1.4.1.215.1.2.2.13 | nwfpEthernetTable | 1 | 3 | A table of ethernet-port-specific information for the FastPipes. This table augments the Ethernet RFC1398 MIB. |
| 1.3.6.1.4.1.215.1.2.2.18 | nwfpBOOTPServerIPAddress | 1 | 1 | The IP address of the BOOTP Server that responded to the FastPipes's BOOTP request. |
| 1.3.6.1.4.1.215.1.2.2.19 | nwfpBOOTPEthernetIF | 1 | 1 | The Ethernet interface number that successfully completed the BOOTP interaction. |
| 1.3.6.1.4.1.215.1.2.2.20 | nwfpUplinkSoftwarePath | 1 | 1 | The path to the switch software file. Following this path will reveal the actual version of the file. |
| 1.3.6.1.4.1.215.1.2.2.21 | nwfpSerialNumber | 1 | 1 | The hardware serial number. |
| 1.3.6.1.4.1.215.1.2.2.22 | nwfpConfiguration | 1 | 1 | This object returns the type of base module that is being queried. |
| 1.3.6.1.4.1.215.1.2.2.23 | nwfpUpLinkEEPROMVersion | 1 | 1 | The uplink EEPROM version. The string 'unknown' is returned if the value is not known. |
| 1.3.6.1.4.1.215.1.2.2.24 | nwfpUpLinkManufactureDate | 1 | 1 | The uplink manufacture date. The string 'unknown' is returned if the value is not known. |
| 1.3.6.1.4.1.215.1.2.2.25 | nwfpUpLinkSerialNumber | 1 | 1 | The uplink serial number. |
| 1.3.6.1.4.1.215.1.2.2.26 | nwfpUpLinkConfiguration | 1 | 1 | This object returns the type of HSSP (Uplink) module that is in the base unit. |
| 1.3.6.1.4.1.215.1.2.2.27 | nwfpSoftwarePath | 1 | 1 | The path to the switch software file. Following this path will reveal the actual version of the file. |
| 1.3.6.1.4.1.215.1.2.2.28 | nwfpCurrentBooterSoftwareVersion | 1 | 1 | The version of Booter software currently running on the switch. The version is an ASCII string. |
| 1.3.6.1.4.1.215.1.2.2.29 | nwfpFutureBooterSoftwareVersion | 1 | 1 | The version of Booter software the switch will run after the next reset. If this variable is different than nwfpCurrentSoftwareV… |
| 1.3.6.1.4.1.215.1.2.2.30 | nwfpBooterSoftwarePath | 1 | 1 | The path to the Booter software file. Following this path will reveal the actual version of the file. |
| 1.3.6.1.4.1.215.1.2.2.31 | nwfpSaveConfig | 1 | 1 | This object allows the user to permanently save configuration parameters into the NVRAM of a managed device. It can only be writ… |
| 1.3.6.1.4.1.215.1.2.2.32 | nwfpFddiIPFrag | 1 | 1 | When on(2), the FastPipes FDDI Uplink will perform IP fragmentation. When off(1), IP fragmentation is not done and FDDI frames c… |
| 1.3.6.1.4.1.215.1.2.2.33 | nwfpFddiToEthIPTrans | 1 | 1 | This attribute defines how FDDI frames containing IP packets get translated into Ethernet frames. When automatic(3) mode is sele… |
| 1.3.6.1.4.1.215.1.2.2.34 | nwfpFddiSNAPToEthIPXTrans | 1 | 1 | This attribute defines how incoming FDDI SNAP frames containing IPX information are translated into ethernet frames. When ethern… |
| 1.3.6.1.4.1.215.1.2.2.35 | nwfpFddi8022ToEthIPXTrans | 1 | 1 | This attribute defines how incoming FDDI 802.2 frames containing IPX information are translated into ethernet frames. When the 8… |
| 1.3.6.1.4.1.215.1.2.2.36 | nwfpFddiLocTrafFiltering | 1 | 1 | Defines whether or not traffic local to the FDDI network the FastPipes is connected to is filtered or not (i.e not forwarded to … |
| 1.3.6.1.4.1.215.1.2.2.37 | nwfpSpanningTreeEnable | 1 | 1 | When set to enable(1), the FastPipes will run the Spanning Tree Protocol (STP). When set to disable(2), the FastPipes will not r… |
| 1.3.6.1.4.1.215.1.2.2.38 | nwfpTpFdbMaxSize | 1 | 1 | Gives the maximum number of entries that the forwarding data base may have |
| 1.3.6.1.4.1.215.1.2.2.39 | nwfpTpFdbNbEntriesUsed | 1 | 1 | Gives the number of entries currently existing in the forwarding data base. |
| 1.3.6.1.4.1.215.1.2.2.40 | nwfpEthIPX8023ToFddiTrans | 1 | 1 | When set to ieee8022(2), an LLC header is added to the FDDI frame, between the MAC header and the IPX header. When set to ethern… |
| 1.3.6.1.4.1.215.1.2.2.41 | nwfpPowerSupplyNumber | 1 | 1 | The number of system power supplies installed (regardless of their current state) in the FastPipe product. |
| 1.3.6.1.4.1.215.1.2.2.42 | nwfpPowerSupplyTable | 1 | 3 | A table of system power supply specific information for the FastPipes. |
| 1.3.6.1.4.1.215.1.2.2.43 | nwfpFanNumber | 1 | 1 | The number of system fans installed (regardless of their current state) in the FastPipe product. |
| 1.3.6.1.4.1.215.1.2.2.44 | nwfpFanTable | 1 | 3 | A table of system fan specific information for the FastPipes. |
| 1.3.6.1.4.1.215.1.2.2.45 | nwfpMonitorPort | 1 | 1 | The index value of a port which will receive all traffic from the ports specified in the nwfpMonitorSource bitmask. Acceptable va… |
| 1.3.6.1.4.1.215.1.2.2.46 | nwfpMonitorSource | 1 | 1 | A bitmask of the port numbers to monitor. This bitmask (which must not include the port number used for nwfpMonitorPort) specifi… |
| 1.3.6.1.4.1.215.1.2.2.47 | nwfpMonitorPortStatus | 1 | 1 | Status value of RMON monitoring. When set to disabled the port specified in nwfpMonitorPort will not receive monitored data. Whe… |