Controls the degree to which frames are copied and
parsed. Under high network loads this control can be
used to prevent agent overload.
Parsed from file startek.mib.txt
Company: None
Module: STARTEK-PRIVATE-MIB
Controls the degree to which frames are copied and
parsed. Under high network loads this control can be
used to prevent agent overload.
Parsed from file STARTEK-PRIVATE-MIB.mib
Module: STARTEK-PRIVATE-MIB
Child arc 0 is used to translate between SNMPv1 and SNMPv2 notification parameters as explained in IETF RFC 2576, section 3.
configParseControl OBJECT-TYPE SYNTAX INTEGER { parseAll(1), parseMost(2), parseLess(3), parseNone(4) } ACCESS read-write STATUS mandatory DESCRIPTION "Controls the degree to which frames are copied and parsed. Under high network loads this control can be used to prevent agent overload." ::= { configuration 11 }
configParseControl OBJECT-TYPE SYNTAX INTEGER { parseAll(1), parseMost(2), parseLess(3), parseNone(4) } ACCESS read-write STATUS mandatory DESCRIPTION "Controls the degree to which frames are copied and parsed. Under high network loads this control can be used to prevent agent overload." ::= { configuration 11 }
| OID | Name | Sub children | Sub Nodes Total | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.260.2.3.11.0 | configParseControl | 0 | 0 | None |
| OID | Name | Sub children | Sub Nodes Total | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.260.2.3.1 | configEPROMSize | 1 | 1 | The Quantity of EPROM installed (number of bytes). |
| 1.3.6.1.4.1.260.2.3.2 | configFLASHSize | 1 | 1 | The Quantity of FLASH installed (number of bytes). |
| 1.3.6.1.4.1.260.2.3.3 | configFLASHCount | 1 | 1 | The Quantity of FLASH installed (number of ICs). |
| 1.3.6.1.4.1.260.2.3.4 | configDRAMSize | 1 | 1 | The Quantity of DRAM installed (number of bytes). |
| 1.3.6.1.4.1.260.2.3.5 | configDRAMCount | 1 | 1 | The Quantity of DRAM installed (number of SIMMs). |
| 1.3.6.1.4.1.260.2.3.6 | configRS232Number | 1 | 1 | The Number of RS-232 ports in the RS-232 port table. |
| 1.3.6.1.4.1.260.2.3.7 | configRS232PortTable | 1 | 10 | A list of port entries. The number of entries is given by the value of configRS232Number. |
| 1.3.6.1.4.1.260.2.3.8 | configMonitorMode | 1 | 1 | The mode of operation of the monitor port. The monitor port is COM2 (if present, COM1 if not). |
| 1.3.6.1.4.1.260.2.3.9 | configMonitorInput | 1 | 1 | Controls whether the monitor function will accept input. |
| 1.3.6.1.4.1.260.2.3.10 | configMonitorDiags | 1 | 1 | Controls whether the monitor function will produce diagnostic output. |
| 1.3.6.1.4.1.260.2.3.12 | configBootSource | 1 | 1 | Describes where the agent is executing code from. |
| 1.3.6.1.4.1.260.2.3.13 | configIPXBroadcastState | 1 | 1 | Controls the transmitting of IPX broadcasts. |
| 1.3.6.1.4.1.260.2.3.14 | configBOOTPControlState | 1 | 1 | Controls whether the agent uses BOOTP to obtain the IP address for the TR IP interface. |
| 1.3.6.1.4.1.260.2.3.15 | configUseDefaultCommunityStringsState | 1 | 1 | Controls whether the default community strings of 'StarTek' (read-write) and 'public' (read-only) are valid (enabled) when perfor… |