Vendor: BinTec Communications GmbH
Module: BIANCA-BRICK-IPSEC-MIB
[Automatically extracted from oidview.com]
ipsecGlobContDefaultRule OBJECT-TYPE SYNTAX INTEGER { drop(1), pass(2) } ACCESS read-write STATUS mandatory DESCRIPTION "This object specifies how to treat packets which do not match any entry in the traffic lists of the active peers or the pre-and post IPSec rules. Possible values: drop(1), pass(2) ::= { ipsecGlobalsContinued 2 }
ipsecGlobContDefaultRule OBJECT-TYPE SYNTAX INTEGER { drop(1), pass(2) } ACCESS read-write STATUS mandatory DESCRIPTION "This object specifies how to treat packets which do not match any entry in the traffic lists of the active peers. Possible values: drop(1), pass(2) ::= { ipsecGlobalsContinued 2 }
| OID | Name | Sub children | Sub Nodes Total | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.272.4.26.11.2.0 | ipsecGlobContDefaultRule | 0 | 0 | None |
| OID | Name | Sub children | Sub Nodes Total | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.272.4.26.11.1 | ipsecGlobContPreIpsecRules | 1 | 1 | This object specifies an index in the IPsec traffic table containing a list of traffic definitions which has to be considered pri… |
| 1.3.6.1.4.1.272.4.26.11.4 | ipsecGlobContUse32BitCpi | 1 | 1 | None |
| 1.3.6.1.4.1.272.4.26.11.5 | ipsecGlobContNoWellKnownCpis | 1 | 1 | None |
| 1.3.6.1.4.1.272.4.26.11.7 | ipsecGlobContNoPmtuDiscovery | 1 | 1 | None |
| 1.3.6.1.4.1.272.4.26.11.8 | ipsecGlobContDefaultPmtuTtl | 1 | 1 | This object specifies the time-to-live (in minutes) of a PMTU value derived from an ICMP PMTU message received for an IPSec packe… |
| 1.3.6.1.4.1.272.4.26.11.9 | ipsecGlobContPrivateInterface | 1 | 1 | This object specifies the index of the systems' private interface. If the private interface is set (i.e. non-negative), certain a… |
| 1.3.6.1.4.1.272.4.26.11.10 | ipsecGlobContSaSyncInterface | 1 | 1 | None |
| 1.3.6.1.4.1.272.4.26.11.11 | ipsecGlobContPostIpsecRules | 1 | 1 | This object specifies an index in the IPsec traffic table containing a list of traffic definitions which has to be considered aft… |
| 1.3.6.1.4.1.272.4.26.11.12 | ipsecGlobContDefaultPfsIdentity | 1 | 1 | None |
| 1.3.6.1.4.1.272.4.26.11.13 | ipsecGlobContIkeLoggingLevel | 1 | 1 | This object specifies the IKE logging level. IKE log messages are output as syslog messages on level debug. Note that the global … |
| 1.3.6.1.4.1.272.4.26.11.14 | ipsecGlobContDialBlockTime | 1 | 1 | Amount of time in minutes how long an ipsecDial entry remains in state blocked-for-outgoing after a cost producing trigger call w… |
| 1.3.6.1.4.1.272.4.26.11.15 | ipsecGlobContPfsIdentityDelay | 1 | 1 | This object specifies the number of seconds to wait before deleting the underlying phase 1 SA after a Phase 2 SA has been establi… |
| 1.3.6.1.4.1.272.4.26.11.16 | ipsecGlobContHeartbeatDefault | 1 | 1 | None |
| 1.3.6.1.4.1.272.4.26.11.17 | ipsecGlobContHeartbeatInterval | 1 | 1 | This object specifies the time interval in seconds between heartbeats. At this rate heartbeats are sent and/or expected if config… |
| 1.3.6.1.4.1.272.4.26.11.18 | ipsecGlobContHeartbeatTolerance | 1 | 1 | This object specifies the maximum number of missing heartbeats allowed before an SA is discarded. |
| 1.3.6.1.4.1.272.4.26.11.64 | ipsecGlobContMinFcChangeDelay | 1 | 1 | The time (in milliseconds) the update of the filter code is delayed. If more changes to the filter code occur during this time, t… |
| 1.3.6.1.4.1.272.4.26.11.65 | ipsecGlobContMaxFcChangeDelay | 1 | 1 | The maximum time (in milliseconds) the update of the filter code is delayed if multiple phase 2 SA negotiations occur within ipse… |
| 1.3.6.1.4.1.272.4.26.11.66 | ipsecGlobContObsoleteFeatureMask | 1 | 1 | Some obsolete features are represented by a bit in this mask and could be re-enabled for testing or compatibility purpose. A mask… |
| 1.3.6.1.4.1.272.4.26.11.67 | ipsecGlobContUniqueIds | 1 | 1 | This flag decides how an INITIAL CONTACT notification from a remote peer is handled: if set to true, all SAs negotiated with peer… |
| 1.3.6.1.4.1.272.4.26.11.68 | ipsecGlobContAntiSpoofing | 1 | 1 | This object allows to enable the IPSec anti spoofing feature: It makes IPSec drop incoming clear text packets which are configure… |