Description of last diagnostic failure.
Parsed from file cascade.mib.txt
Company: None
Module: CASCADE-MIB
Description of last diagnostic failure.
Parsed from file CASCADE-MIB.mib
Module: CASCADE-MIB
Vendor: Cascade Communications Corp.
Module: CASCADE-MIB
[Automatically extracted from oidview.com]
pportDiagResultStr OBJECT-TYPE SYNTAX DisplayString ACCESS read-only STATUS mandatory DESCRIPTION "Description of last diagnostic failure." ::= { pportEntry 28 }
pportDiagResultStr OBJECT-TYPE SYNTAX DisplayString ACCESS read-only STATUS mandatory DESCRIPTION "Description of last diagnostic failure." ::= { pportEntry 28 }
To many brothers! Only 100 nearest brothers are shown.
| OID | Name | Sub children | Sub Nodes Total | Description |
|---|---|---|---|---|
| ... | ||||
| 1.3.6.1.4.1.277.1.4.2.1.1 | pportSlotId | 0 | 0 | The slot number of the corresponding physical port. |
| 1.3.6.1.4.1.277.1.4.2.1.2 | pportId | 0 | 0 | The port number of the corresponding physical port on the board. |
| 1.3.6.1.4.1.277.1.4.2.1.3 | pportAdminType | 0 | 0 | The defined type of the board which the physical port is on. |
| 1.3.6.1.4.1.277.1.4.2.1.4 | pportNumLport | 0 | 0 | The number of logical ports on the physical port. |
| 1.3.6.1.4.1.277.1.4.2.1.5 | pportDataRate | 0 | 0 | An estimate of the physical port's data rate in bits per second. The data rate can't be an arbitrary value. The legal values are … |
| 1.3.6.1.4.1.277.1.4.2.1.6 | pportType | 0 | 0 | The actual type of the physical port. |
| 1.3.6.1.4.1.277.1.4.2.1.7 | pportRecvClock | 0 | 0 | The receive clock source. This object works in cooperation with pportXmitClock. The following are the various values for differen… |
| 1.3.6.1.4.1.277.1.4.2.1.8 | pportXmitClock | 0 | 0 | The transmit clock source. This object works in cooperation with pportXmitClock. The following are the various values for differe… |
| 1.3.6.1.4.1.277.1.4.2.1.9 | pportAdminStatus | 0 | 0 | The desired state of the physical port. |
| 1.3.6.1.4.1.277.1.4.2.1.10 | pportOperStatus | 0 | 0 | The current state of the physical port. |
| 1.3.6.1.4.1.277.1.4.2.1.11 | pportDs1LineType | 0 | 0 | The line type of the T1 or FT1-24B port. ANSI ESF is equivalent to Bellcore ESF. |
| 1.3.6.1.4.1.277.1.4.2.1.12 | pportDs1ZeroCoding | 0 | 0 | The variety of zero code suppression used on the T1 or FT1-24B link. Jammed bit is equivalent to dsx1JBZS where the DS0s will ru… |
| 1.3.6.1.4.1.277.1.4.2.1.13 | pportDs1LineBuildout | 0 | 0 | The line build out or line length specification for the DS1 or DSX-1 transmitter. These values are card specific: 10 port DSX-1 ca… |
| 1.3.6.1.4.1.277.1.4.2.1.14 | pportDiagTestId | 0 | 0 | Identification for the diagnostics tests to be run. |
| 1.3.6.1.4.1.277.1.4.2.1.15 | pportDiagTestRuns | 0 | 0 | The number of passes of the diagnostics tests to be run. The default value is 1. |
| 1.3.6.1.4.1.277.1.4.2.1.16 | pportInOctets | 0 | 0 | The total number of octets received on the physical port, including framing characters. |
| 1.3.6.1.4.1.277.1.4.2.1.17 | pportInFrames | 0 | 0 | The total number of frames received on the physical port. |
| 1.3.6.1.4.1.277.1.4.2.1.18 | pportInDiscards | 0 | 0 | The total number of inbound frames discarded. |
| 1.3.6.1.4.1.277.1.4.2.1.19 | pportInErrors | 0 | 0 | The total number of inbound frames that contained erroneous headers (e.g., illegal or unknown DLCIs). |
| 1.3.6.1.4.1.277.1.4.2.1.20 | pportOutOctets | 0 | 0 | The total number of octets transmitted out of the physical port, including framing characters. |
| 1.3.6.1.4.1.277.1.4.2.1.21 | pportOutFrames | 0 | 0 | The total number of frames transmitted out of the physical port. |
| 1.3.6.1.4.1.277.1.4.2.1.22 | pportOutDiscards | 0 | 0 | The total number of outbound frames discarded due to severe congestion. |
| 1.3.6.1.4.1.277.1.4.2.1.23 | pportOutErrors | 0 | 0 | The total number of outbound frames that causes xmit errors. |
| 1.3.6.1.4.1.277.1.4.2.1.24 | pportDiagState | 0 | 0 | The current state of the diagnostic on this physical port. |
| 1.3.6.1.4.1.277.1.4.2.1.25 | pportDiagOptionStr | 0 | 0 | Optional parameters to the diagnostic. |
| 1.3.6.1.4.1.277.1.4.2.1.26 | pportDiagPassCount | 0 | 0 | Number of successful diagnostic passes. |
| 1.3.6.1.4.1.277.1.4.2.1.27 | pportDiagFailCount | 0 | 0 | Number of failed diagnostic passes. |
| 1.3.6.1.4.1.277.1.4.2.1.29 | pportLinkDownReason | 0 | 0 | Reason why the link is down. The blue-alarm is equivalent to the Alarm Indication Signal (AIS) failure. |
| 1.3.6.1.4.1.277.1.4.2.1.30 | pportInterface | 0 | 0 | Actual interface connected to Multi-Interface Port or ATM-IWU. |
| 1.3.6.1.4.1.277.1.4.2.1.31 | pportAdminInterface | 0 | 0 | Configured interface connected to Multi-Interface Port or ATM-IWU. |
| 1.3.6.1.4.1.277.1.4.2.1.32 | pportCellScramble | 0 | 0 | Configured ATM cell payload scrambling. |
| 1.3.6.1.4.1.277.1.4.2.1.33 | pportCbitParity | 0 | 0 | Configured ATM DS3 C-bit Parity. |
| 1.3.6.1.4.1.277.1.4.2.1.34 | pportMaxBufferSize | 0 | 0 | Maximum receive/transmit buffer size for the ATM UNI DS3 IOP |
| 1.3.6.1.4.1.277.1.4.2.1.35 | pportPeakCellRate0 | 0 | 0 | Peak Cell Rate (cell/sec.) for rate queue #0. rate queues 0 - 3 are high priority |
| 1.3.6.1.4.1.277.1.4.2.1.36 | pportPeakCellRate1 | 0 | 0 | Peak Cell Rate (cell/sec.) for rate queue #1. rate queues 0 - 3 are high priority |
| 1.3.6.1.4.1.277.1.4.2.1.37 | pportPeakCellRate2 | 0 | 0 | Peak Cell Rate (cell/sec.) for rate queue #2. rate queues 0 - 3 are high priority |
| 1.3.6.1.4.1.277.1.4.2.1.38 | pportPeakCellRate3 | 0 | 0 | Peak Cell Rate (cell/sec.) for rate queue #3. rate queues 0 - 3 are high priority |
| 1.3.6.1.4.1.277.1.4.2.1.39 | pportPeakCellRate4 | 0 | 0 | Peak Cell Rate (cell/sec.) for rate queue #4. rate queues 4 - 7 are low priority |
| 1.3.6.1.4.1.277.1.4.2.1.40 | pportPeakCellRate5 | 0 | 0 | Peak Cell Rate (cell/sec.) for rate queue #5. rate queues 4 - 7 are low priority |
| 1.3.6.1.4.1.277.1.4.2.1.41 | pportPeakCellRate6 | 0 | 0 | Peak Cell Rate (cell/sec.) for rate queue #6. rate queues 4 - 7 are low priority |
| 1.3.6.1.4.1.277.1.4.2.1.42 | pportPeakCellRate7 | 0 | 0 | Peak Cell Rate (cell/sec.) for rate queue #7. rate queues 4 - 7 are low priority |
| 1.3.6.1.4.1.277.1.4.2.1.43 | pportInCells | 0 | 0 | The total number of cells received |
| 1.3.6.1.4.1.277.1.4.2.1.44 | pportInErrorCells | 0 | 0 | The total number of cells received with error |
| 1.3.6.1.4.1.277.1.4.2.1.45 | pportOutCells | 0 | 0 | The total number of cells transmitted |
| 1.3.6.1.4.1.277.1.4.2.1.46 | pportDs3LineBuildout | 0 | 0 | The line build out or line length specification for the DS3 transmitter. 1-port ATM-UNI DS3 card The accepted values are: 1 - 0 to… |
| 1.3.6.1.4.1.277.1.4.2.1.47 | pportSetDS0LoopUp | 0 | 0 | Bit map used to set one or more DS0's into loopback. Low bit corresponds to DS0 1. If a bit is set that DS0 is put into loopback. |
| 1.3.6.1.4.1.277.1.4.2.1.48 | pportSetDS0LoopDown | 0 | 0 | Bit map used to set one or more DS0's out of loopback. Low bit corresponds to DS0 1. If a bit is set that DS0 is put out of loop… |
| 1.3.6.1.4.1.277.1.4.2.1.49 | pportDS0LoopUpStatus | 0 | 0 | Bit map reporting which DS0's have gone into loopback since the last time this variable was read |
| 1.3.6.1.4.1.277.1.4.2.1.50 | pportDS0LoopDownStatus | 0 | 0 | Bit map reporting which DS0's have gone out of loopback since the last time this variable was read |
| 1.3.6.1.4.1.277.1.4.2.1.51 | pportDS0LoopStatus | 0 | 0 | Bit map reporting which DS0's are currently in loopback. Low bit corresponds to DS0 1 |
| 1.3.6.1.4.1.277.1.4.2.1.52 | pportISDN | 0 | 0 | Specifies whether ISDN PRI is enabled for this physical port |
| 1.3.6.1.4.1.277.1.4.2.1.53 | pportdsx3LoopbackConfig | 0 | 0 | Integer used to set the loopback state of the DS3 or E3 |
| 1.3.6.1.4.1.277.1.4.2.1.54 | pportdsx3SendCode | 0 | 0 | Integer used to send loopback code to far-end DS3 |
| 1.3.6.1.4.1.277.1.4.2.1.55 | pportdsx3LoopStatus | 0 | 0 | Integer indicating the current loopback status of the DS3 or E3 |
| 1.3.6.1.4.1.277.1.4.2.1.56 | pportdsx3FEACStatus | 0 | 0 | Integer indicating the current DS3 FAEC status: DS3 Equipment Failure (1), DS3 LOS (2), DS3 Out of Frame (4), DS3 AIS receive… |
| 1.3.6.1.4.1.277.1.4.2.1.57 | pportds1LoopbackConfig | 0 | 0 | Integer used to set the loopback state of the DS1 |
| 1.3.6.1.4.1.277.1.4.2.1.58 | pportds1SendCode | 0 | 0 | Integer used to send loopback code to far-end DS1 |
| 1.3.6.1.4.1.277.1.4.2.1.59 | pportds1LoopStatus | 0 | 0 | Integer indicating the current loopback status of the DS1 |
| 1.3.6.1.4.1.277.1.4.2.1.60 | pportSetClkBkup | 0 | 0 | The desired clock source backup if the card is set in external clock source mode |
| 1.3.6.1.4.1.277.1.4.2.1.61 | pportAtmIdleWord | 0 | 0 | The word used to stuff the payload of the ATM idle cell |
| 1.3.6.1.4.1.277.1.4.2.1.62 | pportAtmDisCardMode | 0 | 0 | The desired clock source backup if the card is set in external clock source mode |
| 1.3.6.1.4.1.277.1.4.2.1.63 | pportAtmLastUnconfiguredVpi | 0 | 0 | This entry holds the Vpi read from the last Unconfigured atm cell received. This entry applies to ATM pports only. |
| 1.3.6.1.4.1.277.1.4.2.1.64 | pportAtmLastUnconfiguredVci | 0 | 0 | This entry holds the Vci read from the last Unconfigured atm cell received. This entry applies to ATM pports only. |
| 1.3.6.1.4.1.277.1.4.2.1.65 | pportAtmUnconfiguredCells | 0 | 0 | This entry holds a count of the number of Unconfigured ATM cells received. This entry applies to ATM pports only. |
| 1.3.6.1.4.1.277.1.4.2.1.66 | pportAtmNumBitsVCI | 0 | 0 | This entry holds a count of the VCI bits supported by this ATM card. |
| 1.3.6.1.4.1.277.1.4.2.1.67 | pportAtmNumBitsVPI | 0 | 0 | This entry holds a count of the VPI bits supported by this ATM card. |
| 1.3.6.1.4.1.277.1.4.2.1.68 | pportAtmInterfaceType | 0 | 0 | Integer used to set ATM UNI or NNI type |
| 1.3.6.1.4.1.277.1.4.2.1.69 | pportSonetSDHLoopbackConfig | 0 | 0 | Integer used to set the loopback state of the Sonet/SDH port |
| 1.3.6.1.4.1.277.1.4.2.1.70 | pportSonetSDHLoopStatus | 0 | 0 | Integer indicating the current loopback status of the Sonet/SDH port |
| 1.3.6.1.4.1.277.1.4.2.1.71 | pportOutDiscardsCell | 0 | 0 | The total number of outbound cell discarded due to congestion. |
| 1.3.6.1.4.1.277.1.4.2.1.72 | pportAtmPlcp | 0 | 0 | The PLCP maintains the state of the ATM Physical Layer Convergence Protocol. When the protocol is disabled atm direct mapping is … |
| 1.3.6.1.4.1.277.1.4.2.1.73 | pportCbrTargetClockMode | 0 | 0 | The clocking method to be used by the CBR card. 4-port CBR card 1 - synchronous (external) clocking 2 - SRTS clocking 3 - adaptive… |
| 1.3.6.1.4.1.277.1.4.2.1.74 | pportCbrCurrentClockMode | 0 | 0 | The clocking method currently used by the CBR card. 4-port CBR card 1 - synchronous (external) clocking 2 - SRTS clocking 3 - adap… |
| 1.3.6.1.4.1.277.1.4.2.1.75 | pportClockMasterChannel | 0 | 0 | The number of the channel (lport) on this pport that is used as ACM/SRTS master for this line interface: 4-port CBR E1/DS1 card (… |
| 1.3.6.1.4.1.277.1.4.2.1.76 | pportFibreType, pportFiberType | 0 | 0 | The type of fibre connected to the ATM-IWU. Its type determines the maximum transmission distance. 1-port ATM-IWU STM-1/STS-3c ca… |
| 1.3.6.1.4.1.277.1.4.2.1.77 | pportLaserStatus | 0 | 0 | The configured state of the laser: 1-port ATM-IWU STM-1/STS-3c card & Topaz 4-port OC3 & STM-1 card 1 - off 2 - on |
| 1.3.6.1.4.1.277.1.4.2.1.78 | pportMaxActiveVpiBits | 0 | 0 | The maximum number of active VPI bits configured for use at the ATM interface. At the ATM UNI, the maximum number of active VPI … |
| ... | ||||