This object specifies whether changes to certain fundamental
configuration parameters (as specified for the corresponding
MIB variables) shall cause the device to restart automatically.
The auto restart functionality is always enabled after
restarting the bridge.
NOTICE:
In general, disabling this functionality is not recommended,
since some changes may cause the device to behave erratically
(which may be the reason why the device has to restart).
However, for the initial configuration of the device (i.e.
before it is operational, it is usually safe to postpone
restarting the device until all configuration changes
have been made.
Parsed from file Olicom-MIB.mib
Module: Olicom-MIB
controlAutoRestart OBJECT-TYPE SYNTAX INTEGER { enabled(1), disabled(2) } ACCESS read-write STATUS optional DESCRIPTION "This object specifies whether changes to certain fundamental configuration parameters (as specified for the corresponding MIB variables) shall cause the device to restart automatically. The auto restart functionality is always enabled after restarting the bridge. NOTICE: In general, disabling this functionality is not recommended, since some changes may cause the device to behave erratically (which may be the reason why the device has to restart). However, for the initial configuration of the device (i.e. before it is operational, it is usually safe to postpone restarting the device until all configuration changes have been made." ::= { control 12 }
| OID | Name | Sub children | Sub Nodes Total | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.285.5.1 | controlRestart | 0 | 0 | Writing any value other than zero to this variable causes the device program to restart. |
| 1.3.6.1.4.1.285.5.2 | controlConfigChangeCounter | 0 | 0 | This variable contains the number of times, any part of the configuration has been changed by any of the management systems contr… |
| 1.3.6.1.4.1.285.5.3 | controlTrapTable | 1 | 6 | This table contains an entry for each enterprise-specific TRAP this device is capable of sending. The only writable field in the … |
| 1.3.6.1.4.1.285.5.4 | controlLoadProtocol | 0 | 0 | This variable defines which protocol should be used for downloading configuration and program code. Notice that a specific Olicom… |
| 1.3.6.1.4.1.285.5.5 | controlLoadFilename | 0 | 0 | In the Load protocols where it is relevant this variable contains the name of the file to be downloaded. |
| 1.3.6.1.4.1.285.5.6 | controlLoadServerMACAddress | 0 | 0 | This object specifies the MAC address of the Load server used for download. Only used if the Load protocol defined by the control… |
| 1.3.6.1.4.1.285.5.7 | controlLoadServerIPAddress | 0 | 0 | This object specifies the IP address of the Load server used for download. Only used if the Load protocol defined by the controlL… |
| 1.3.6.1.4.1.285.5.8 | controlLoadServerIPXAddress | 0 | 0 | This object specifies the IPX address of the Load server used for download. Only used if the Load protocol defined by the control… |
| 1.3.6.1.4.1.285.5.9 | controlLoadStart | 0 | 0 | Writing any value other than zero to this variable causes a download to start. While reading, it returns the current status of tr… |
| 1.3.6.1.4.1.285.5.10 | controlTime | 0 | 0 | The internal clock in the device. This is measured in seconds since 00:00:00 on 1 January 1970 (i.e. UNIX standard time). |
| 1.3.6.1.4.1.285.5.11 | controlEnableRmon | 0 | 0 | This object specifies whether RMON probe is enabled or disabled. If the device does not support RMON only disabled is allowed. Se… |
| 1.3.6.1.4.1.285.5.13 | controlSwAdminStatus | 0 | 0 | This object controls the state of the SW images in systems where more than one image is present. In the OC-9100 the state of each… |
| 1.3.6.1.4.1.285.5.15 | controlFlashConfigSize | 0 | 0 | The total number of bytes in the configuration FLASH, or rather, in one of the two alternating sections. |
| 1.3.6.1.4.1.285.5.16 | controlFlashConfigFree | 0 | 0 | The number of free bytes in the configuration FLASH. |
| 1.3.6.1.4.1.285.5.17 | controlFlashConfigState | 0 | 0 | Controls the state of the FLASH configuration. The states are as follows: normal default - The DEFAULT button has been activated. c… |
| 1.3.6.1.4.1.285.5.18 | controlDelayedRestart | 0 | 0 | Writing value n to this variable will cause device to restart after n seconds. Writing zero cancels the reboot. Writing new value … |
| 1.3.6.1.4.1.285.5.19 | controlLoadProggress | 0 | 0 | Number of bytes transmitted so far. 0 if no transmission is currently in progress. |
| 1.3.6.1.4.1.285.5.20 | controlLoadFileSize | 0 | 0 | Length of the file being transmitted. 0 if no transmission is currently in progress or if the size is unknown. |
| 1.3.6.1.4.1.285.5.21 | controlTftpClient | 3 | 13 | None |
| 1.3.6.1.4.1.285.5.22 | controlRestartType | 0 | 0 | The type of restart that will be performed after next reboot request. After any kind of reboot the value of this object should be… |