Sets the binary communications protocol (BCP) for
communicating over a parallel interface to a PostScript
printer.
Choices
Normal: Enables standard, ASCII (7-bit) hex protocol.
Data is sent and received in ASCII format. This mode is
recommended if you do not print binary data. It was
designed for data in the printable ASCII range. Print
jobs can change this setting through PostScript
operators.
Normal Fixed: Enables standard, ASCII (7-bit) hex
protocol. Print jobs cannot change this setting through
PostScript operators.
Binary: Enables quoted binary communications
protocol (BCP). Print jobs can change this setting
through PostScript operators. Data in the printable
ASCII range also prints.
Binary Fixed: Enables binary communications protocol
(BCP). Print jobs cannot alter change this setting
through PostScript operators. Data in the printable
ASCII range also prints.
Default
Normal
Parsed from file QMS-MIB.mib
Module: QMS-MIB
Vendor: QMS, Inc.
Module: QMS-MIB
[Automatically extracted from oidview.com]
qmsParPSProtocol OBJECT-TYPE SYNTAX INTEGER { normal(1), normalfixed(2), binary(3), binaryfixed(4) } ACCESS read-write STATUS mandatory DESCRIPTION "Sets the binary communications protocol (BCP) for communicating over a parallel interface to a PostScript printer. Choices Normal: Enables standard, ASCII (7-bit) hex protocol. Data is sent and received in ASCII format. This mode is recommended if you do not print binary data. It was designed for data in the printable ASCII range. Print jobs can change this setting through PostScript operators. Normal Fixed: Enables standard, ASCII (7-bit) hex protocol. Print jobs cannot change this setting through PostScript operators. Binary: Enables quoted binary communications protocol (BCP). Print jobs can change this setting through PostScript operators. Data in the printable ASCII range also prints. Binary Fixed: Enables binary communications protocol (BCP). Print jobs cannot alter change this setting through PostScript operators. Data in the printable ASCII range also prints. Default Normal" ::= { qmsParallel 100 }
OID | Name | Sub children | Sub Nodes Total | Description |
---|---|---|---|---|
1.3.6.1.4.1.480.1.161.101 | qmsParMode | 0 | 0 | The parallel interface supports Centronics parallel communication as well as IEEE 1284 bidirectional parallel communication. Choic… |
1.3.6.1.4.1.480.1.161.102 | qmsParEmulation | 0 | 0 | Sets the parallel interface emulation. Choices PostScript, HPGL, HPPCL, HEXDUMP, LN03, QUIC2 CCITT, Line Printer, TIFF, CALS, CGM,… |
1.3.6.1.4.1.480.1.161.103 | qmsParPriority | 0 | 0 | Allows you to specify which jobs are printed first, according to the interface through which they are received, when jobs are rec… |
1.3.6.1.4.1.480.1.161.104 | qmsParBufferSize | 0 | 0 | Sets the minimum number of kilobytes of system memory allocated to the parallel interface. Default 15 Notes This value must be less … |
1.3.6.1.4.1.480.1.161.111 | qmsParSpoolTimeout | 0 | 0 | Sets the number of seconds the interface waits for data from the host before terminating a spooled print job. Choices 0-99999 Defau… |
1.3.6.1.4.1.480.1.161.112 | qmsParEndDocumentMode | 0 | 0 | Enables (and identifies an end-of-job sequence) or disables data stream sensing for the end-of-document (EOD) command. Choices Non… |
1.3.6.1.4.1.480.1.161.113 | qmsParDataBits | 0 | 0 | Sets the number of data bits transmitted per character. Choices 7 Bits, 8 Bits Default 8 Bits |