This attribute is migrated to the AtmTmProv group.
This attribute is a vector of four traffic parameters whose meanings
are defined by the rxTrafficDescType attribute. The values of peak
cell rate (PCR) and sustained cell rate (SCR) are expressed in
cell/s. Maximum burst size (MBS) is expressed in cells. The value
of CDVT is expressed in microseconds. The values of PCR, SCR,
MBS and CDVT are used for usage parameter control (UPC).
When rxTrafficDescType is 1 or 2, all of the parameters must be set
to zero (unused).
When rxTrafficDescType is 3, parameter 1 represents the PCR for
CLP equal to 0 and 1 traffic. Parameter 1 must be non-zero.
Parameters 2 and 3 must be set to zero (unused).
When rxTrafficDescType is 4, parameter 1 represents the PCR for
CLP equal to 0 and 1 traffic; parameter 2 represents the PCR for
CLP equal to 0 traffic with cell discard. Parameters 1 and 2 must be
non-zero. Parameter 3 must be set to zero (unused). Parameter 1
must be greater than or equal to parameter 2.
When rxTrafficDescType is 5, parameter 1 represents the PCR for
CLP equal to 0 and 1 traffic; parameter 2 represents the PCR for
CLP equal to 0 traffic with cell tagging. Parameters 1 and 2 must be
non-zero. Parameter 3 must be set to zero (unused). Parameter 1
must be greater than or equal to parameter 2.
When rxTrafficDescType is a 6, parameter 1 represents the PCR for
CLP equal to 0 and 1 traffic; parameter 2 represents the SCR for
CLP equal to 0 and 1 traffic; parameter 3 represents the MBS for
CLP equal to 0 and 1 traffic. Parameters 1, 2 and 3 must be non-
zero. Parameter 1 must be greater than or equal to Parameter 2.
When rxTrafficDescType is 7, parameter 1 represents the PCR for
CLP equal to 0 and 1 traffic; parameter 2 represents the SCR for
CLP equal to 0 traffic with cell discard; parameter 3 represents the
MBS for CLP equal to 0 traffic. Parameters 1, 2 and 3 must be non-
zero. Parameter 1 must be greater than or equal to parameter 2.
When rxTrafficDescType is 8, parameter 1 represents the PCR for
CLP equal to 0 and 1 traffic; parameter 2 represents the SCR for
CLP equal to 0 traffic with cell tagging; parameter 3 represents the
MBS for CLP equal to 0 traffic. Parameter 1, 2 and 3 must be non-
zero. Parameter 1 must be greater than or equal to parameter 2.
When rxTrafficDescType is any value from 3 through 8, parameter
4 represents the CDVT. If this value is zero, the CDVT is taken
from the ConnectionAdministrator defaults for the particular
atmServiceCategory of this connection.
When rxTrafficDescriptorType is 3 through 8, there are certain
extreme combinations of rxTrafficDescParm which are outside the
capabilities of the UPC hardware. The check prov command detects
such cases and generates an error message. If this happens, adjust
the parameters until they fall within the supported limits.
To calculate the limits, use the following formulae:
I1 = 1 000 000 000 / PCR
L1 = CDVT * 1000
I2 = 1 000 000 000 / SCR
L2 = CDVT + (MBS - 1) * (I2 - I1)
I1 and I2 must be less than or equal to 335 523 840. I1 + L1 must
be less than or equal to 1 342 156 800. I2 + L2 must be less than or
equal to 1 342 156 800. Note that I2 and L2 only apply when the
rxTrafficDescriptorType is 6 through 8.
If the values of I1, L1, I2 or L2 are closer to the limits described
above, a further restriction applies. Specifically, if either:
I1 > 41 940 480 or
I2 > 41 940 480 or
I1 + L1 > 167 769 600 or
I2 + L2 > 167 769 600
then both I1 and I2 must be greater than 20 480.
Parameter 5 of the rxTrafficDescParm is always unused.
If the rxTrafficDescType is sameAsTx, the values in this attribute
are taken from the txTrafficDescParm.
Parsed from file nortelPP-atmCoreV1_BG00S4C.mib.txt
Company: None
Module: Nortel-Magellan-Passport-AtmCoreMIB
This attribute is migrated to the AtmTmProv group.
This attribute is a vector of four traffic parameters whose meanings
are defined by the rxTrafficDescType attribute. The values of peak
cell rate (PCR) and sustained cell rate (SCR) are expressed in
cell/s. Maximum burst size (MBS) is expressed in cells. The value
of CDVT is expressed in microseconds. The values of PCR, SCR,
MBS and CDVT are used for usage parameter control (UPC).
When rxTrafficDescType is 1 or 2, all of the parameters must be set
to zero (unused).
When rxTrafficDescType is 3, parameter 1 represents the PCR for
CLP equal to 0 and 1 traffic. Parameter 1 must be non-zero.
Parameters 2 and 3 must be set to zero (unused).
When rxTrafficDescType is 4, parameter 1 represents the PCR for
CLP equal to 0 and 1 traffic; parameter 2 represents the PCR for
CLP equal to 0 traffic with cell discard. Parameters 1 and 2 must be
non-zero. Parameter 3 must be set to zero (unused). Parameter 1
must be greater than or equal to parameter 2.
When rxTrafficDescType is 5, parameter 1 represents the PCR for
CLP equal to 0 and 1 traffic; parameter 2 represents the PCR for
CLP equal to 0 traffic with cell tagging. Parameters 1 and 2 must be
non-zero. Parameter 3 must be set to zero (unused). Parameter 1
must be greater than or equal to parameter 2.
When rxTrafficDescType is a 6, parameter 1 represents the PCR for
CLP equal to 0 and 1 traffic; parameter 2 represents the SCR for
CLP equal to 0 and 1 traffic; parameter 3 represents the MBS for
CLP equal to 0 and 1 traffic. Parameters 1, 2 and 3 must be non-
zero. Parameter 1 must be greater than or equal to Parameter 2.
When rxTrafficDescType is 7, parameter 1 represents the PCR for
CLP equal to 0 and 1 traffic; parameter 2 represents the SCR for
CLP equal to 0 traffic with cell discard; parameter 3 represents the
MBS for CLP equal to 0 traffic. Parameters 1, 2 and 3 must be non-
zero. Parameter 1 must be greater than or equal to parameter 2.
When rxTrafficDescType is 8, parameter 1 represents the PCR for
CLP equal to 0 and 1 traffic; parameter 2 represents the SCR for
CLP equal to 0 traffic with cell tagging; parameter 3 represents the
MBS for CLP equal to 0 traffic. Parameter 1, 2 and 3 must be non-
zero. Parameter 1 must be greater than or equal to parameter 2.
When rxTrafficDescType is any value from 3 through 8, parameter
4 represents the CDVT. If this value is zero, the CDVT is taken
from the ConnectionAdministrator defaults for the particular
atmServiceCategory of this connection.
When rxTrafficDescriptorType is 3 through 8, there are certain
extreme combinations of rxTrafficDescParm which are outside the
capabilities of the UPC hardware. The check prov command detects
such cases and generates an error message. If this happens, adjust
the parameters until they fall within the supported limits.
To calculate the limits, use the following formulae:
I1 = 1 000 000 000 / PCR
L1 = CDVT * 1000
I2 = 1 000 000 000 / SCR
L2 = CDVT + (MBS - 1) * (I2 - I1)
I1 and I2 must be less than or equal to 335 523 840. I1 + L1 must
be less than or equal to 1 342 156 800. I2 + L2 must be less than or
equal to 1 342 156 800. Note that I2 and L2 only apply when the
rxTrafficDescriptorType is 6 through 8.
If the values of I1, L1, I2 or L2 are closer to the limits described
above, a further restriction applies. Specifically, if either:
I1 > 41 940 480 or
I2 > 41 940 480 or
I1 + L1 > 167 769 600 or
I2 + L2 > 167 769 600
then both I1 and I2 must be greater than 20 480.
Parameter 5 of the rxTrafficDescParm is always unused.
If the rxTrafficDescType is sameAsTx, the values in this attribute
are taken from the txTrafficDescParm.
Parsed from file Nortel-Magellan-Passport-AtmCoreMIB.mib
Module: Nortel-Magellan-Passport-AtmCoreMIB
Vendor: Northern Telecom, Ltd.
Module: Nortel-Magellan-Passport-AtmCoreMIB
[Automatically extracted from oidview.com]
atmIfVptVccVcdRxTdpTable OBJECT-TYPE SYNTAX SEQUENCE OF AtmIfVptVccVcdRxTdpEntry ACCESS not-accessible STATUS obsolete DESCRIPTION "This attribute is migrated to the AtmTmProv group. This attribute is a vector of four traffic parameters whose meanings are defined by the rxTrafficDescType attribute. The values of peak cell rate (PCR) and sustained cell rate (SCR) are expressed in cell/s. Maximum burst size (MBS) is expressed in cells. The value of CDVT is expressed in microseconds. The values of PCR, SCR, MBS and CDVT are used for usage parameter control (UPC). When rxTrafficDescType is 1 or 2, all of the parameters must be set to zero (unused). When rxTrafficDescType is 3, parameter 1 represents the PCR for CLP equal to 0 and 1 traffic. Parameter 1 must be non-zero. Parameters 2 and 3 must be set to zero (unused). When rxTrafficDescType is 4, parameter 1 represents the PCR for CLP equal to 0 and 1 traffic; parameter 2 represents the PCR for CLP equal to 0 traffic with cell discard. Parameters 1 and 2 must be non-zero. Parameter 3 must be set to zero (unused). Parameter 1 must be greater than or equal to parameter 2. When rxTrafficDescType is 5, parameter 1 represents the PCR for CLP equal to 0 and 1 traffic; parameter 2 represents the PCR for CLP equal to 0 traffic with cell tagging. Parameters 1 and 2 must be non-zero. Parameter 3 must be set to zero (unused). Parameter 1 must be greater than or equal to parameter 2. When rxTrafficDescType is a 6, parameter 1 represents the PCR for CLP equal to 0 and 1 traffic; parameter 2 represents the SCR for CLP equal to 0 and 1 traffic; parameter 3 represents the MBS for CLP equal to 0 and 1 traffic. Parameters 1, 2 and 3 must be non- zero. Parameter 1 must be greater than or equal to Parameter 2. When rxTrafficDescType is 7, parameter 1 represents the PCR for CLP equal to 0 and 1 traffic; parameter 2 represents the SCR for CLP equal to 0 traffic with cell discard; parameter 3 represents the MBS for CLP equal to 0 traffic. Parameters 1, 2 and 3 must be non- zero. Parameter 1 must be greater than or equal to parameter 2. When rxTrafficDescType is 8, parameter 1 represents the PCR for CLP equal to 0 and 1 traffic; parameter 2 represents the SCR for CLP equal to 0 traffic with cell tagging; parameter 3 represents the MBS for CLP equal to 0 traffic. Parameter 1, 2 and 3 must be non- zero. Parameter 1 must be greater than or equal to parameter 2. When rxTrafficDescType is any value from 3 through 8, parameter 4 represents the CDVT. If this value is zero, the CDVT is taken from the ConnectionAdministrator defaults for the particular atmServiceCategory of this connection. When rxTrafficDescriptorType is 3 through 8, there are certain extreme combinations of rxTrafficDescParm which are outside the capabilities of the UPC hardware. The check prov command detects such cases and generates an error message. If this happens, adjust the parameters until they fall within the supported limits. To calculate the limits, use the following formulae: I1 = 1 000 000 000 / PCR L1 = CDVT * 1000 I2 = 1 000 000 000 / SCR L2 = CDVT + (MBS - 1) * (I2 - I1) I1 and I2 must be less than or equal to 335 523 840. I1 + L1 must be less than or equal to 1 342 156 800. I2 + L2 must be less than or equal to 1 342 156 800. Note that I2 and L2 only apply when the rxTrafficDescriptorType is 6 through 8. If the values of I1, L1, I2 or L2 are closer to the limits described above, a further restriction applies. Specifically, if either: I1 > 41 940 480 or I2 > 41 940 480 or I1 + L1 > 167 769 600 or I2 + L2 > 167 769 600 then both I1 and I2 must be greater than 20 480. Parameter 5 of the rxTrafficDescParm is always unused. If the rxTrafficDescType is sameAsTx, the values in this attribute are taken from the txTrafficDescParm." ::= { atmIfVptVccVcd 298 }
atmIfVptVccVcdRxTdpTable OBJECT-TYPE SYNTAX SEQUENCE OF AtmIfVptVccVcdRxTdpEntry ACCESS not-accessible STATUS obsolete DESCRIPTION "This attribute is migrated to the AtmTmProv group. This attribute is a vector of four traffic parameters whose meanings are defined by the rxTrafficDescType attribute. The values of peak cell rate (PCR) and sustained cell rate (SCR) are expressed in cell/s. Maximum burst size (MBS) is expressed in cells. The value of CDVT is expressed in microseconds. The values of PCR, SCR, MBS and CDVT are used for usage parameter control (UPC). When rxTrafficDescType is 1 or 2, all of the parameters must be set to zero (unused). When rxTrafficDescType is 3, parameter 1 represents the PCR for CLP equal to 0 and 1 traffic. Parameter 1 must be non-zero. Parameters 2 and 3 must be set to zero (unused). When rxTrafficDescType is 4, parameter 1 represents the PCR for CLP equal to 0 and 1 traffic; parameter 2 represents the PCR for CLP equal to 0 traffic with cell discard. Parameters 1 and 2 must be non-zero. Parameter 3 must be set to zero (unused). Parameter 1 must be greater than or equal to parameter 2. When rxTrafficDescType is 5, parameter 1 represents the PCR for CLP equal to 0 and 1 traffic; parameter 2 represents the PCR for CLP equal to 0 traffic with cell tagging. Parameters 1 and 2 must be non-zero. Parameter 3 must be set to zero (unused). Parameter 1 must be greater than or equal to parameter 2. When rxTrafficDescType is a 6, parameter 1 represents the PCR for CLP equal to 0 and 1 traffic; parameter 2 represents the SCR for CLP equal to 0 and 1 traffic; parameter 3 represents the MBS for CLP equal to 0 and 1 traffic. Parameters 1, 2 and 3 must be non- zero. Parameter 1 must be greater than or equal to Parameter 2. When rxTrafficDescType is 7, parameter 1 represents the PCR for CLP equal to 0 and 1 traffic; parameter 2 represents the SCR for CLP equal to 0 traffic with cell discard; parameter 3 represents the MBS for CLP equal to 0 traffic. Parameters 1, 2 and 3 must be non- zero. Parameter 1 must be greater than or equal to parameter 2. When rxTrafficDescType is 8, parameter 1 represents the PCR for CLP equal to 0 and 1 traffic; parameter 2 represents the SCR for CLP equal to 0 traffic with cell tagging; parameter 3 represents the MBS for CLP equal to 0 traffic. Parameter 1, 2 and 3 must be non- zero. Parameter 1 must be greater than or equal to parameter 2. When rxTrafficDescType is any value from 3 through 8, parameter 4 represents the CDVT. If this value is zero, the CDVT is taken from the ConnectionAdministrator defaults for the particular atmServiceCategory of this connection. When rxTrafficDescriptorType is 3 through 8, there are certain extreme combinations of rxTrafficDescParm which are outside the capabilities of the UPC hardware. The check prov command detects such cases and generates an error message. If this happens, adjust the parameters until they fall within the supported limits. To calculate the limits, use the following formulae: I1 = 1 000 000 000 / PCR L1 = CDVT * 1000 I2 = 1 000 000 000 / SCR L2 = CDVT + (MBS - 1) * (I2 - I1) I1 and I2 must be less than or equal to 335 523 840. I1 + L1 must be less than or equal to 1 342 156 800. I2 + L2 must be less than or equal to 1 342 156 800. Note that I2 and L2 only apply when the rxTrafficDescriptorType is 6 through 8. If the values of I1, L1, I2 or L2 are closer to the limits described above, a further restriction applies. Specifically, if either: I1 > 41 940 480 or I2 > 41 940 480 or I1 + L1 > 167 769 600 or I2 + L2 > 167 769 600 then both I1 and I2 must be greater than 20 480. Parameter 5 of the rxTrafficDescParm is always unused. If the rxTrafficDescType is sameAsTx, the values in this attribute are taken from the txTrafficDescParm." ::= { atmIfVptVccVcd 298 }
OID | Name | Sub children | Sub Nodes Total | Description |
---|---|---|---|---|
1.3.6.1.4.1.562.2.4.1.114.9.20.2.298.1 | atmIfVptVccVcdRxTdpEntry | 2 | 2 | An entry in the atmIfVptVccVcdRxTdpTable. |
OID | Name | Sub children | Sub Nodes Total | Description |
---|---|---|---|---|
1.3.6.1.4.1.562.2.4.1.114.9.20.2.1 | atmIfVptVccVcdRowStatusTable | 1 | 5 | This entry controls the addition and deletion of atmIfVptVccVcd components. |
1.3.6.1.4.1.562.2.4.1.114.9.20.2.2 | atmIfVptVccVcdTm | 7 | 67 | None |
1.3.6.1.4.1.562.2.4.1.114.9.20.2.100 | atmIfVptVccVcdLbkTable | 1 | 5 | This group contains the provisionable loopback attributes for a Vcc, Vpc, or Vpt component. Note that certain loopback requests … |
1.3.6.1.4.1.562.2.4.1.114.9.20.2.110 | atmIfVptVccVcdTrafficTable | 1 | 18 | This group contains traffic related provisionable attributes for the Vcc and Vpc components. The attributes' operational values … |
1.3.6.1.4.1.562.2.4.1.114.9.20.2.111 | atmIfVptVccVcdAcctTable | 1 | 2 | This group contains the provisionable ATM accounting attributes for a Vcc, Vpc, or Vpt component. |
1.3.6.1.4.1.562.2.4.1.114.9.20.2.297 | atmIfVptVccVcdTxTdpTable | 1 | 3 | This attribute is migrated to the AtmTmProv group. This attribute is a vector of five traffic parameters whose meanings are defi… |
1.3.6.1.4.1.562.2.4.1.114.9.20.2.359 | atmIfVptVccVcdFqpTable | 1 | 3 | This attribute is migrated to the AtmTmProv group. This attribute is a vector of three elements that specify the quality of serv… |
1.3.6.1.4.1.562.2.4.1.114.9.20.2.360 | atmIfVptVccVcdBqpTable | 1 | 3 | This attribute is migrated to the AtmTmProv group. This attribute is a vector of three elements that specify the quality of serv… |