This attribute specifies the expected savings (percent reduction) in
required bandwidth if silence suppression is used. If silence
suppression is used, the bandwidth required for the connection will
be lower than if silence suppression is not used. However, the
routing system will not be aware of the unused bandwidth unless
that bandwidth is specified by this attribute.
If the value specified for the expected savings is too low, then some
bandwidth made available by the use of silence suppression will be
wasted. If the value specified for the expected savings is too high,
then some connections may fail to set up because the routing system
will over-calculate the amount of bandwidth available.
The effectiveness of silence suppression can be influenced by
language related speech patterns.
Parsed from file nortelPP-dcmeV1_BG00S4C.mib.txt
Company: None
Module: Nortel-Magellan-Passport-DcmeMIB
This attribute specifies the expected savings (percent reduction) in
required bandwidth if silence suppression is used. If silence
suppression is used, the bandwidth required for the connection will
be lower than if silence suppression is not used. However, the
routing system will not be aware of the unused bandwidth unless
that bandwidth is specified by this attribute.
If the value specified for the expected savings is too low, then some
bandwidth made available by the use of silence suppression will be
wasted. If the value specified for the expected savings is too high,
then some connections may fail to set up because the routing system
will over-calculate the amount of bandwidth available.
The effectiveness of silence suppression can be influenced by
language related speech patterns.
Parsed from file Nortel-Magellan-Passport-DcmeMIB.mib
Module: Nortel-Magellan-Passport-DcmeMIB
Vendor: Northern Telecom, Ltd.
Module: Nortel-Magellan-Passport-DcmeMIB
[Automatically extracted from oidview.com]
dcmeProfileSilenceSuppressionFactor OBJECT-TYPE SYNTAX Unsigned32 (0..60) ACCESS read-write STATUS mandatory DESCRIPTION "This attribute specifies the expected savings (percent reduction) in required bandwidth if silence suppression is used. If silence suppression is used, the bandwidth required for the connection will be lower than if silence suppression is not used. However, the routing system will not be aware of the unused bandwidth unless that bandwidth is specified by this attribute. If the value specified for the expected savings is too low, then some bandwidth made available by the use of silence suppression will be wasted. If the value specified for the expected savings is too high, then some connections may fail to set up because the routing system will over-calculate the amount of bandwidth available. The effectiveness of silence suppression can be influenced by language related speech patterns." DEFVAL { 40 } ::= { dcmeProfileFrOpsEntry 6 }
dcmeProfileSilenceSuppressionFactor OBJECT-TYPE SYNTAX Unsigned32 (0..60) ACCESS read-write STATUS mandatory DESCRIPTION "This attribute specifies the expected savings (percent reduction) in required bandwidth if silence suppression is used. If silence suppression is used, the bandwidth required for the connection will be lower than if silence suppression is not used. However, the routing system will not be aware of the unused bandwidth unless that bandwidth is specified by this attribute. If the value specified for the expected savings is too low, then some bandwidth made available by the use of silence suppression will be wasted. If the value specified for the expected savings is too high, then some connections may fail to set up because the routing system will over-calculate the amount of bandwidth available. The effectiveness of silence suppression can be influenced by language related speech patterns." DEFVAL { 40 } ::= { dcmeProfileFrOpsEntry 6 }
| OID | Name | Sub children | Sub Nodes Total | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.562.2.4.1.129.2.11.1.1 | dcmeProfileVoiceEncoding | 0 | 0 | This attribute specifies the encoding of voice traffic. A voiceEncoding setting of g711G726 specifies that either pulse code mod… |
| 1.3.6.1.4.1.562.2.4.1.129.2.11.1.2 | dcmeProfileMaxVoiceBitRate | 0 | 0 | This attribute specifies the maximum possible bit rate (minimum possible compression rate) during a voice call on this channel w… |
| 1.3.6.1.4.1.562.2.4.1.129.2.11.1.3 | dcmeProfileMinVoiceBitRate | 0 | 0 | This attribute specifies the minimum possible bit rate (maximum possible compression rate) during a voice call on this channel w… |
| 1.3.6.1.4.1.562.2.4.1.129.2.11.1.4 | dcmeProfileVoiceTrafficOptimization | 0 | 0 | This attribute specifies how to optimize voice traffic. If voiceTrafficOptimization is bandwidth, voice traffic is optimized to p… |
| 1.3.6.1.4.1.562.2.4.1.129.2.11.1.5 | dcmeProfileSilenceSuppression | 0 | 0 | This attribute specifies when silence suppression is performed. It applies to both voice and modem calls. If silenceSuppression i… |
| 1.3.6.1.4.1.562.2.4.1.129.2.11.1.7 | dcmeProfileEchoCancellation | 0 | 0 | This attribute specifies whether echo cancellation is performed on calls using this profile as specified by ITU-T G.165. It appl… |
| 1.3.6.1.4.1.562.2.4.1.129.2.11.1.9 | dcmeProfileModemFaxEncoding | 0 | 0 | This attribute specifies how modem and fax traffic is encoded. Modem and fax traffic are identified by an inband 2100 Hz tone. Pr… |
| 1.3.6.1.4.1.562.2.4.1.129.2.11.1.10 | dcmeProfileMaxModemFaxG711G726Rate | 0 | 0 | This attribute specifies the maximum possible bit rate (minimum possible compression rate) during a modem call on this channel. … |
| 1.3.6.1.4.1.562.2.4.1.129.2.11.1.11 | dcmeProfileMinModemFaxG711G726Rate | 0 | 0 | This attribute specifies the minimum possible bit rate (maximum possible compression rate) during a modem call on this channel. … |
| 1.3.6.1.4.1.562.2.4.1.129.2.11.1.12 | dcmeProfileFaxIdleSuppressionG711G726 | 0 | 0 | This attribute specifies whether fax idle suppression is performed on fax traffic on calls using this profile. It only applies t… |
| 1.3.6.1.4.1.562.2.4.1.129.2.11.1.13 | dcmeProfileInsertedOutputDelay | 0 | 0 | This attribute specifies the amount of added output delay used to compensate for cross network delay variations. It applies to v… |
| 1.3.6.1.4.1.562.2.4.1.129.2.11.1.14 | dcmeProfileIngressAudioGain | 0 | 0 | This attribute specifies the gain in dB that is applied to data coming from outside the network before it is transferred across … |
| 1.3.6.1.4.1.562.2.4.1.129.2.11.1.15 | dcmeProfileEgressAudioGain | 0 | 0 | This attribute specifies the gain in dB that is applied to data leaving the network on this route. It applies to voice, modem an… |
| 1.3.6.1.4.1.562.2.4.1.129.2.11.1.16 | dcmeProfileSpeechHangoverTime | 0 | 0 | This attribute specifies the time after the end of speech before silence suppression starts. It applies only to voice traffic. H… |
| 1.3.6.1.4.1.562.2.4.1.129.2.11.1.17 | dcmeProfileComfortNoiseCap | 0 | 0 | This attribute specifies the maximum level at which comfort noise is generated. The comfort noise is limited by comfortNoiseCap … |
| 1.3.6.1.4.1.562.2.4.1.129.2.11.1.18 | dcmeProfileModemFaxSpeechDiscrim | 0 | 0 | This attribute specifies whether this Dcme differentiates between modemFax traffic and speech. If modemFaxSpeechDiscrim is on and… |
| 1.3.6.1.4.1.562.2.4.1.129.2.11.1.19 | dcmeProfileV17EncodedAsG711G726 | 0 | 0 | This attribute specifies how services using this Profile negotiate with V.17 fax machines. This attribute is not used unless the… |
| 1.3.6.1.4.1.562.2.4.1.129.2.11.1.20 | dcmeProfileDtmfRegeneration | 0 | 0 | This attribute specifies the DTMF regeneration parameter used during negotiation with the remote end across the subnet. If dtmfR… |
| 1.3.6.1.4.1.562.2.4.1.129.2.11.1.21 | dcmeProfileMaxFaxRelayRate | 0 | 0 | This attribute specifies the maximum desired fax relay rate. This attribute only applies if modemFaxEncoding is faxRelayOnly or f… |