This attribute indicates the failure cause on this link. Possible values
are:
noFailure: there is no failure on this link.
interfaceDown: the physical port used by the link is down.
lif: the link is in loss of IMA frame (LIF) state.
lods: the link is in loss of delay synchronization (LODS) state; that
is, it has exhibited a differential delay which is greater than the
maximum differential delay tolerated by the IMA group. It must be
noted that hysteresis is used for the LODS condition.
protocolError: the link is down because of a time-out or because
bad values are being received in IMA Control Protocol (ICP) cells.
remoteFailure: the far end link is down.
misconnected: the link is down because the IMA group has
declared, after using its transmit test pattern procedure, that this link
is not properly connected. This value can occur only if the protocol
for the IMA group is atmForum10.
unsupportedFrameLength: the link is down because it is receiving
from the far end a frame length which is not supported by the local
IMA group. This value can occur only if the protocol for the IMA
group is atmForum10.
unsupportedSymmetry: the link is down because it is receiving
from the far end a group symmetry which is not supported by the
local IMA group. This value can occur only if the protocol for the
IMA group is atmForum10.
noIcp: the link is down because it is not receiving IMA Control
Protocol (ICP) cells. This value can occur only if the protocol for
the IMA group is atmForum10.
Parsed from file nortelPC-imaV1.mib.txt
Company: None
Module: Nortel-MsCarrier-MscPassport-ImaMIB
This attribute indicates the failure cause on this link. Possible values
are:
noFailure: there is no failure on this link.
interfaceDown: the physical port used by the link is down.
lif: the link is in loss of IMA frame (LIF) state.
lods: the link is in loss of delay synchronization (LODS) state; that
is, it has exhibited a differential delay which is greater than the
maximum differential delay tolerated by the IMA group. It must be
noted that hysteresis is used for the LODS condition.
protocolError: the link is down because of a time-out or because
bad values are being received in IMA Control Protocol (ICP) cells.
remoteFailure: the far end link is down.
misconnected: the link is down because the IMA group has
declared, after using its transmit test pattern procedure, that this link
is not properly connected. This value can occur only if the protocol
for the IMA group is atmForum10.
unsupportedFrameLength: the link is down because it is receiving
from the far end a frame length which is not supported by the local
IMA group. This value can occur only if the protocol for the IMA
group is atmForum10.
unsupportedSymmetry: the link is down because it is receiving
from the far end a group symmetry which is not supported by the
local IMA group. This value can occur only if the protocol for the
IMA group is atmForum10.
noIcp: the link is down because it is not receiving IMA Control
Protocol (ICP) cells. This value can occur only if the protocol for
the IMA group is atmForum10.
Parsed from file Nortel-MsCarrier-MscPassport-ImaMIB.mib
Module: Nortel-MsCarrier-MscPassport-ImaMIB
Vendor: Northern Telecom, Ltd.
Module: Nortel-MsCarrier-MscPassport-ImaMIB
[Automatically extracted from oidview.com]
mscLpDS3ImaLkFailureCause OBJECT-TYPE SYNTAX INTEGER { noFailure(0), interfaceDown(1), lif(2), lods(3), protocolError(4), remoteFailure(5), misconnected(6), unsupportedFrameLength(7), unsupportedSymmetry(8), noIcp(9) } ACCESS read-only STATUS mandatory DESCRIPTION "This attribute indicates the failure cause on this link. Possible values are: noFailure: there is no failure on this link. interfaceDown: the physical port used by the link is down. lif: the link is in loss of IMA frame (LIF) state. lods: the link is in loss of delay synchronization (LODS) state; that is, it has exhibited a differential delay which is greater than the maximum differential delay tolerated by the IMA group. It must be noted that hysteresis is used for the LODS condition. protocolError: the link is down because of a time-out or because bad values are being received in IMA Control Protocol (ICP) cells. remoteFailure: the far end link is down. misconnected: the link is down because the IMA group has declared, after using its transmit test pattern procedure, that this link is not properly connected. This value can occur only if the protocol for the IMA group is atmForum10. unsupportedFrameLength: the link is down because it is receiving from the far end a frame length which is not supported by the local IMA group. This value can occur only if the protocol for the IMA group is atmForum10. unsupportedSymmetry: the link is down because it is receiving from the far end a group symmetry which is not supported by the local IMA group. This value can occur only if the protocol for the IMA group is atmForum10. noIcp: the link is down because it is not receiving IMA Control Protocol (ICP) cells. This value can occur only if the protocol for the IMA group is atmForum10." ::= { mscLpDS3ImaLkOperEntry 1 }
mscLpDS3ImaLkFailureCause OBJECT-TYPE SYNTAX INTEGER { noFailure(0), interfaceDown(1), lif(2), lods(3), protocolError(4), remoteFailure(5), misconnected(6), unsupportedFrameLength(7), unsupportedSymmetry(8), noIcp(9) } ACCESS read-only STATUS mandatory DESCRIPTION "This attribute indicates the failure cause on this link. Possible values are: noFailure: there is no failure on this link. interfaceDown: the physical port used by the link is down. lif: the link is in loss of IMA frame (LIF) state. lods: the link is in loss of delay synchronization (LODS) state; that is, it has exhibited a differential delay which is greater than the maximum differential delay tolerated by the IMA group. It must be noted that hysteresis is used for the LODS condition. protocolError: the link is down because of a time-out or because bad values are being received in IMA Control Protocol (ICP) cells. remoteFailure: the far end link is down. misconnected: the link is down because the IMA group has declared, after using its transmit test pattern procedure, that this link is not properly connected. This value can occur only if the protocol for the IMA group is atmForum10. unsupportedFrameLength: the link is down because it is receiving from the far end a frame length which is not supported by the local IMA group. This value can occur only if the protocol for the IMA group is atmForum10. unsupportedSymmetry: the link is down because it is receiving from the far end a group symmetry which is not supported by the local IMA group. This value can occur only if the protocol for the IMA group is atmForum10. noIcp: the link is down because it is not receiving IMA Control Protocol (ICP) cells. This value can occur only if the protocol for the IMA group is atmForum10." ::= { mscLpDS3ImaLkOperEntry 1 }
| OID | Name | Sub children | Sub Nodes Total | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.562.36.2.1.12.5.7.3.11.1.2 | mscLpDS3ImaLkRemoteDefect | 0 | 0 | This attribute indicates the IMA remote defect indicator (RDI) currently being received on this link. Possible values are: noDefe… |
| 1.3.6.1.4.1.562.36.2.1.12.5.7.3.11.1.3 | mscLpDS3ImaLkRemoteLid | 0 | 0 | This attribute indicates the link identifier (LID) used by the remote IMA group on the physical link. A value of 0 will be displ… |
| 1.3.6.1.4.1.562.36.2.1.12.5.7.3.11.1.4 | mscLpDS3ImaLkRelativeDelay | 0 | 0 | This attribute indicates the latest measured differential delay (rounded up in milliseconds) between this link and the link, in … |
| 1.3.6.1.4.1.562.36.2.1.12.5.7.3.11.1.5 | mscLpDS3ImaLkLastOifCause | 0 | 0 | This attribute indicates the cause of the last out of IMA frame (OIF) anomaly on the link. It will always have a value of noOif … |