This attribute indicates whether the LMI is in an error condition or
whether the LMI procedures are behaving normally. When
operating with no LMI protocol, this attribute is always set to
normalCondition. When operating with LMI procedures, this
attribute is set to errorCondition after n392 of the last n393 events
are in error. The consequence of an errorCondition is that all
DLCIs on this interface will become inactive in both directions. The
errorCondition is cleared and a normalCondition is indicated when
a sufficient number of events have occurred without error. In ANSI,
this occurs when n393 consecutive good events take place.
If the procedures attribute is set to autoConfigure, this attribute is
set to configuring while adaptive LMI determines which LMI
procedures are running on the link. A single LMI error event during
auto configuration causes the attribute value to change to
errorCondition. If during configuring no LMI message is received,
an LMI errorCondition is raised after n392 x t392 seconds.
Parsed from file nortelPC-frameRelayUniV1.mib.txt
Company: None
Module: Nortel-MsCarrier-MscPassport-FrameRelayUniMIB
This attribute indicates whether the LMI is in an error condition or
whether the LMI procedures are behaving normally. When
operating with no LMI protocol, this attribute is always set to
normalCondition. When operating with LMI procedures, this
attribute is set to errorCondition after n392 of the last n393 events
are in error. The consequence of an errorCondition is that all
DLCIs on this interface will become inactive in both directions. The
errorCondition is cleared and a normalCondition is indicated when
a sufficient number of events have occurred without error. In ANSI,
this occurs when n393 consecutive good events take place.
If the procedures attribute is set to autoConfigure, this attribute is
set to configuring while adaptive LMI determines which LMI
procedures are running on the link. A single LMI error event during
auto configuration causes the attribute value to change to
errorCondition. If during configuring no LMI message is received,
an LMI errorCondition is raised after n392 x t392 seconds.
Parsed from file Nortel-MsCarrier-MscPassport-FrameRelayUniMIB.mib
Module: Nortel-MsCarrier-MscPassport-FrameRelayUniMIB
Vendor: Northern Telecom, Ltd.
Module: Nortel-MsCarrier-MscPassport-FrameRelayUniMIB
[Automatically extracted from oidview.com]
mscFrUniLmiProtocolStatus OBJECT-TYPE SYNTAX INTEGER { errorCondition(0), normalCondition(1), configuring(2) } ACCESS read-only STATUS mandatory DESCRIPTION "This attribute indicates whether the LMI is in an error condition or whether the LMI procedures are behaving normally. When operating with no LMI protocol, this attribute is always set to normalCondition. When operating with LMI procedures, this attribute is set to errorCondition after n392 of the last n393 events are in error. The consequence of an errorCondition is that all DLCIs on this interface will become inactive in both directions. The errorCondition is cleared and a normalCondition is indicated when a sufficient number of events have occurred without error. In ANSI, this occurs when n393 consecutive good events take place. If the procedures attribute is set to autoConfigure, this attribute is set to configuring while adaptive LMI determines which LMI procedures are running on the link. A single LMI error event during auto configuration causes the attribute value to change to errorCondition. If during configuring no LMI message is received, an LMI errorCondition is raised after n392 x t392 seconds." ::= { mscFrUniLmiPsiEntry 1 }
mscFrUniLmiProtocolStatus OBJECT-TYPE SYNTAX INTEGER { errorCondition(0), normalCondition(1), configuring(2) } ACCESS read-only STATUS mandatory DESCRIPTION "This attribute indicates whether the LMI is in an error condition or whether the LMI procedures are behaving normally. When operating with no LMI protocol, this attribute is always set to normalCondition. When operating with LMI procedures, this attribute is set to errorCondition after n392 of the last n393 events are in error. The consequence of an errorCondition is that all DLCIs on this interface will become inactive in both directions. The errorCondition is cleared and a normalCondition is indicated when a sufficient number of events have occurred without error. In ANSI, this occurs when n393 consecutive good events take place. If the procedures attribute is set to autoConfigure, this attribute is set to configuring while adaptive LMI determines which LMI procedures are running on the link. A single LMI error event during auto configuration causes the attribute value to change to errorCondition. If during configuring no LMI message is received, an LMI errorCondition is raised after n392 x t392 seconds." ::= { mscFrUniLmiPsiEntry 1 }
| OID | Name | Sub children | Sub Nodes Total | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.562.36.2.1.71.4.12.1.2 | mscFrUniLmiOpProcedures | 0 | 0 | The opProcedures attribute indicates the procedures being used for the Local Management Interface. This attribute should be igno… |