Vendor: Telco Systems NAC
Module: EDGELINK-MIB
[Automatically extracted from oidview.com]
elCM OBJECT IDENTIFIER ::= { elM13v1 2 }
elCM OBJECT IDENTIFIER ::= { elM13v1 2 }
| OID | Name | Sub children | Sub Nodes Total | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.564.101.1.2.1 | elCMSystemStatus | 1 | 1 | This DisplayString gives the summary information about the Current EdgeLink100 System Status. The Description includes ... 1) chas… |
| 1.3.6.1.4.1.564.101.1.2.2 | elCMDS3ParityMode | 1 | 1 | Select C-bit or P-bit parity mode for DS3 interface. This Object can't be set when ServiceMode is IN-Service |
| 1.3.6.1.4.1.564.101.1.2.3 | elCMDS3LineBuildout | 1 | 1 | Select line build-out for DS3 Line, 0 to 100 ft, 100 to 200 ft, or 200-450.This MIB Object can't be set when ServiceMode is IN-Se… |
| 1.3.6.1.4.1.564.101.1.2.4 | elCMDS3TxTiming | 1 | 1 | Select mode for DS3 transmit timing. This MIB Object can't be set when ServiceMode is IN-Service |
| 1.3.6.1.4.1.564.101.1.2.5 | elCMProtectionMode | 1 | 1 | In unprotected mode, switching is prohibited. While in protected mode, a standing minor alarm will occur if the off-line card is … |
| 1.3.6.1.4.1.564.101.1.2.6 | elCMCardSelect | 1 | 1 | Read or select choice of on-line card. This operation will force a switch to occur if the off-line card is selected. |
| 1.3.6.1.4.1.564.101.1.2.7 | elCMClearTooManySwitches | 1 | 1 | Clear switching-disabled state which occurs as a result of too many switches between the cards in a protected system in a 10 minu… |
| 1.3.6.1.4.1.564.101.1.2.8 | elCMDS3LoopbackMode | 1 | 1 | Set the DS3 loopback mode to line, terminal, remote, or none. The System can't be set to ds3LpbkRemoteFacility when it is in M13 … |
| 1.3.6.1.4.1.564.101.1.2.9 | elCMDS3ServiceMode | 1 | 1 | Set the DS3 service mode to in-service or out-of-service. Certain service effecting operations can not be initiated unless the DS… |
| 1.3.6.1.4.1.564.101.1.2.10 | elCMCurTimeDate | 1 | 1 | Read or set the system real time clock. The string is in the form MM/DD/YYYY HH:MM:SS. |
| 1.3.6.1.4.1.564.101.1.2.11 | elCMBerThreshold | 1 | 1 | Set the BER Threshold value for the system to 10-6, 10-7, 10-8 or 10-9. BerThershold can't changed when the ServiceMode is IN-Ser… |
| 1.3.6.1.4.1.564.101.1.2.12 | elCMSystemInfo | 1 | 1 | Gets information about the MPU type, board revision, card revision level, software revision, CLEI code, MAC address, and Date of … |
| 1.3.6.1.4.1.564.101.1.2.13 | elCMPPPPortBaudRate | 1 | 1 | Specifies the baud rate on the craft/PPP port when that port is running PPP (i.e. when carrier detect is asserted). |
| OID | Name | Sub children | Sub Nodes Total | Description |
|---|---|---|---|---|
| 1.3.6.1.4.1.564.101.1.1 | elDS1CM | 6 | 22 | None |
| 1.3.6.1.4.1.564.101.1.3 | elCMIfc | 5 | 18 | None |
| 1.3.6.1.4.1.564.101.1.4 | elPM | 2 | 4 | None |
| 1.3.6.1.4.1.564.101.1.5 | elDS1PM | 2 | 4 | None |
| 1.3.6.1.4.1.564.101.1.6 | elDS1PMCur | 1 | 5 | None |
| 1.3.6.1.4.1.564.101.1.7 | elDS1PMIvl | 1 | 6 | None |
| 1.3.6.1.4.1.564.101.1.8 | elDS1PMTot | 1 | 5 | None |
| 1.3.6.1.4.1.564.101.1.9 | elFM | 4 | 8 | None |
| 1.3.6.1.4.1.564.101.1.10 | elFMAlmLog | 1 | 8 | None |
| 1.3.6.1.4.1.564.101.1.11 | elFMCurAlm | 1 | 5 | None |
| 1.3.6.1.4.1.564.101.1.12 | elFMTrapFields | 5 | 10 | None |